Make sure and rate limit all the error messages that might occur. If a problem
occurs then a few messages are enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Small optimization, if dma addresses are 32 bits, then high
bits are always zero.
Signed-off-by: Stephen Hemminger <shemminger@osdl.or>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to zero out the status ring entries after processing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Be more careful about memory barriers. The only place we really
need them is before and after updating the chip's ring interface.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix problems with Yukon FE rev 2 chipset. Don't cut and paste bugs in from
sk98lin driver. Change how the ram buffer is divided up, and make the math
clearer. Also, set the thresholds where rx takes precedence. The threshold
values are just guesses at this point, it might be worth tuning them later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Need to call pci_set_consistent_dma_mask in the case of 64 bit
DMA.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Need to make sure that sky2 receive buffers are 64 bit
aligned. Also, don't need to start off with GFP_ATOMIC
on initial setup.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: e100 whitespace fixes
These are whitespace only fixes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: Handle the return values from pci_* functions
This is to resolve warnings during compile time.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: Fix TX hang and RMCP Ping issue (due to a microcode loading issue)
Set the end of list bit to cause the hardware's transmit state machine to
work correctly and not prevent management (BMC) traffic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sbusfb_compat_ioctl() needs to return int, not long, as that
is what the fb_ops->fb_compat_ioctl method prototype wants.
Need to git rid of the "struct file *file" first argument to
fbiogetputcmap() and fbiogscursor() to match calls done in
sbusfb_compat_ioctl().
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/cassini.c:1930: warning: long unsigned int format, different type arg (arg 4)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk level and remove unnecessary CONFIG_SMP|CONFIG_PREEMPT tests
as this is taken care through the spinlock macros anyway.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I misread the spec when doing the original. I've tested the corrected
version with pre UDMA drives and it now picks the right modes. This is a
specific bug fix rather than an update or new feature item.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds the Intel ICH8 DID's to the ahci.c file for AHCI mode
SATA support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Improves small packet performance with large amounts of reassembly being done in the stack.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This was to fix compilation warnings. Also added log messages when pci_enable_* functions return with an error.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is two patches, the first is adding additional bus information for the 8257{1|2|3} controllers. The second patch was orginally a community patch to print bus type/speed/width, and enhanced by us.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The EEPROM image version is reported as a firmware version for these controllers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added 82571 fiber to WOL fix for dual port adapters.
Added support for 82546GB (Quad Copper).
Added PCIe typedef for x2, igp cable length 115, and extended TX CTRL registers.
Added parity error detection and PCIe CTRL registers.
Added EEPROM config registers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed an issue netpoll would error out during communication, generating the following error:
--netdump[14973]: Got toomany timeouts in handshaking, ...
Even after a kernel panic, netpoll requires two way communication to successfully transfer the crash log to the remote server.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Simplified the logic used to assign the frame_size.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed VLAN support by switching control over to the firmware.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed by moving code to correct location (for 82572 and 82571 controllers).
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the collision distance for 82543 controllers and newer.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Removed duplicate code, TXDCTL and TXDCTL_COUNT_DESC are the same bit and there is no need to set it twice.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These were two separate community submitted patches.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the TX timeout logic to use "end of packet" rather than "next to clean". Updated message log.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch contains two fixes. The first fix is to the tx and rx descriptor rings clean up process. The second fix is to jumbo frames, which cleans up the code logic and removes most of the fifo related limitations on jumbo frames. This is because the driver code now supports splitting a packet across multiple descriptors.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
10/100 speeds seem to have some problems reporting false tx timeouts especially at half duplex. Fixed by using a timeout factor to attempt to mitigate the false timeouts.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed flow control water marks based on PBA size.
Store flow control state in original_fc in addition to fc.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed read_eeprom logic to test use_eerd instead of testing for 82573 controllers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the loopback logic to work for the PCI express adapters.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed stats when using multiple queues.
When multiple queues are enabled, log a message in syslog.
Fixed memory allocation for multiple queues.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix adapter structure to handle multiple queues and prepping the driver for full multiple queue support, some changes are ifdef'd our unless you define CONFIG_E1000_MQ.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Updated the e1000_stats structure and removed mpx for rx_errors and rx_dropped.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added a delay to allow PHY configuration to complete before accessing NVM.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The 82573 controller required different logic than 82571|2 controllers. Corrected the reset logic for 8257{1|2|3} controllers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix so that if a SoL/IDER session is active, do not allow operations which require a PHY reset and instead log a message.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These fixes update the TX and RX ring structures. Prepare driver for up-coming fixes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the TSO workaround for 82571/2 controllers.
Fixed TSO issue where a non-tso packet in a linear SKB which followed a TSO packet would get written back prematurely.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Partition PBA for Jumbo frames based on MTU size.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is now required to avoid
drivers/net/spider_net.c:844: error: 'IPPROTO_TCP' undeclared
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Performance optimizations, changes in these areas:
- RX and TX checksum offload
- correct maximum MTU
- don't use TX interrupts anymore, use a timer instead
- remove some superfluous barriers
- improve RX RAM full handling
From: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Jens Osterkamp <jens.osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The driver incorrectly used dma_addr_t to describe
HW structures and consequently broke when that type
was changed in 2.6.15-rc.
This changed spidernet to use u32 for 32 bit HW defined
structure elements.
From: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
request_firmware() is sometimes problematic, especially
in initramfs, reading the firmware from Open Firmware
is much preferrable.
We still try to get the firmware from the file system
first, in order to support old SLOF releases and to allow
updates of the spidernet firmware without reflashing
the system.
From: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Uploading the device firmware may fail if wrong input data
was provided by the user. This checks for the condition.
From: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
All interrupts controlled by the extended mask register are also
masked by a bit in the main mask register, so there is no need to
directly manipulate the extended mask register.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
mv643xx_eth.c | 81 ++++++++++++++++++----------------------------------------
1 file changed, 26 insertions(+), 55 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Move code from helper functions mv643xx_eth_real_open and mv643xx_eth_real_stop
as they are no longer needed.
Signed-off-by Dale Farnsworth <dale@farnsworth.org>
mv643xx_eth.c | 109 +++++++++++++++++++++++-----------------------------------
1 file changed, 45 insertions(+), 64 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch removes the NETIF_F_HW_CSUM flag to be able to use other protocols
than IPv4. Hardware checksums for IPv4 should continue to work because
NETIF_F_IP_CSUM is still set. The sanity-check has been enhanced to check
the used protocol and to not access skb->iph for non-ipv4-packets.
Signed-off-by: Wolfram Joost <pegasos@frokaschwei.de>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
mv643xx_eth.c | 19 +++++++++++--------
1 file changed, 11 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This driver has historically held a spin_lock during the entire open
and stop functions and while receiving multiple packets. This is
unecessarily long and holds locks during calls that may sleep.
This patch reduces the size of windows where locks are held.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
mv643xx_eth.c | 172 ++++++++++++++++++++++++++++++----------------------------
1 file changed, 91 insertions(+), 81 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Marvell mv643xx ethernet hardware requires that DMA buffers be
aligned to 8-byte boundaries. This patch satisfies this requirement.
Buffers allocated by dev_alloc_skb() only have 4-byte alignment when
slab debugging is enabled.
Also, document that the 2-byte offset to align the IP packets on
receive is a hardware feature and is not tied to NET_IP_ALIGN.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
mv643xx_eth.c | 12 +++++++++---
1 file changed, 9 insertions(+), 3 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This code is adapted from code in a ppc-specific version of the driver.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
mv643xx_eth.c | 201 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++--
1 file changed, 197 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix a NULL pointer dereference.
Fill in the buf_ptr and byte_cnt fields of pkt_info in
eth_tx_return_desc().
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
mv643xx_eth.c | 51 +++++++++++++++++++++------------------------------
1 file changed, 21 insertions(+), 30 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If you do a dma_map_single you must do dma_unmap_single and if you do
a dma_map_page you must do a dma_unmap_page.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
mv643xx_eth.c | 51 +++++++++++++++++++++------------------------------
1 file changed, 21 insertions(+), 30 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add nvram lock count so that calls to tg3_nvram_lock()/unlock() can
be nested. Add error checking to all callers of tg3_nvram_lock()
where appropriate. To prevent nvram lock failures after halting the
firmware, it is also necessary to release firmware's nvram lock in
tg3_halt_cpu().
Update version to 3.48.
Based on David Miller's initial patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'level' of an md array can be set as either a number of a string. When
one is set, the other must be marked 'undefined'. This wasn't being done
in one place: where new arrays are created.
Result: if md1 is a raid1, it is stopped and a raid5 is created there, it
might still appear to be a raid1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of the reasons for keeping these separate before was due to hp690
discontig, and since we have a workaround for that now (abusing some shadow
space so everything is magically contiguous), there's no reason to keep the
targets separate.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After ages my fb ioctl prototype cleanup finally got in. Unfortunately the
patch are so old that the sbus compat_ioctl helper didn't exist back then,
so it's not covered. This patch should fix that issue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's incorrect spinlock usage in espserial_init(): autoconfig() uses
info->lock before it's initialized. The fix is to initialize the spinlock
earlier.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Build kernel/intermodule.c only when required.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the wrong dependency of MTD_OBSOLETE_CHIPS on BROKEN and
marks the non-compiling MTD_AMDSTD and MTD_JEDEC drivers as BROKEN.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains an attempt to properly build hostap.o without
#include'ing C files.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WIRELESS_EXT < 18 will never be true in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ESSIDs can technically include NULL characters. Drivers should not be
adjusting the length of the ESSID before reporting it in their
SIOCGIWESSID handlers. Breaks stuff like wpa_supplicant. Note that ipw
drivers, which seem to currently be the "most correct", don't have this
problem.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Host AP driver has code to support writing firmware to non-volatile
memory, a.k.a. flash. This code has been extensively tested when Host
AP was a standalone driver.
Add a configuration option to the kernel to allow enabling this
functionality. Improve the description of the RAM download option.
Mention cards that require it. Remove obsolete scary comment.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers should not sleep for very long inside an ioctl -
so return EAGAIN and let wpa_supplicant handle the problem.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dev_kfree_skb should not be used with interrupts disabled. Change to
use dev_kfree_skb_irq instead.
Signed-off-by: Graham Gower <graham.gower@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Added remote control support for pinnacle pctv
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Moved MSP_SET_MATRIX to v4l2-common.h
- Fix typos and integer overflows in tea5767.c
- Split old freq field into a tv_freq and a radio_freq. Prevents
that a radio tuner is initialized with a tv frequency or vice versa.
- When switching to radio mode initialize the tuner with the last
used radio frequency (this was already done for the TV mode).
As a result of these changes the tuner module now remembers the
last set radio and TV frequencies, which is what you would expect
to happen.
- Move out of range frequencies to the closest valid frequency as per
v4l2 API spec.
- Fix incorrect initial radio frequency (multiplier is 16000, not 16)
- Add boundary check for out of range frequencies.
- Use new flag to check if the order of the CB and freq. depends on
the last set frequency. That is needed for some tuners or you can
get static as a result. The flag is added for those tuners where I know
that the datasheet indicates that this is necessary.
- For this new check use the last set div value, not the last frequency
as radio frequencies are always much higher due to the 16000 multiplier.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following makes drivers/char/watchdog/sa1100_wdt.c sparse clean.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the following warning which was introduced in 2.6.15-git8 by
commit 7408187d223f63d46a13b6a35b8f96b032c2f623:
CC [M] drivers/media/video/zoran_card.o
drivers/media/video/zoran_card.c: In function `zr36057_init':
drivers/media/video/zoran_card.c:1053: warning: assignment makes integer from pointer without a cast
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Not sure what went wrong here, but SND_PCI_PM_CALLBACKS got deleted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- BOOT_SIZE name is also used at alpha and were breaking
compiling with allyesconfig.
- All BOOT_* renamed to AV7110_BOOT* to fix and keep names
with the same style.
Thanks to Andrew Morton for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Workaround to fix a known regression at cx88-tvaudio.c
- provide a module parameter workaround to always enable
analog output.
Signed-off-by: Panagiotis Christeas <p_christ@hol.gr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- This patch makes some needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Enabled audio PLL. This is mandatory for NICAM sound
- modify FM IF frequency to 5.5MHz for SAA7133/35 if tuner is tda8290
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This makes it possible to build kernels for PReP and/or CHRP
with ARCH=ppc by removing the (non-building) powermac support.
It's now also possible to select PReP and CHRP independently.
Powermac users should now build with ARCH=powerpc instead of
ARCH=ppc. (This does mean that it is no longer possible to
build a 32-bit kernel for a G5.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Un-inline two functions in the pktcdvd driver. This makes the compiled code
172 bytes smaller on my system.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No need for a file argument. If we'd really need it it's in vma->vm_file
already. gbefb and sgivwfb used to set vma->vm_file to the file argument, but
the kernel alrady did that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ioctl and file arguments to ->fb_mmap are totally unused and there's not
reason a driver should need them.
Also update the ->fb_compat_ioctl prototype to be the same as ->fb_mmap.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Seems that the CS5530A chip used in Geode GX1 systems has some crazy feature
that causes SMI traps when accessing the PCI configuration space of the video
device. Various GX1 BIOSes seem to use this 'feature' to hide the real BARs
of the device. This patch disables these traps (in an early PCI fixup) so
that Linux sees the real, physical BARs and not the virtual ones provided by
the BIOS.
This should allow the GX1 framebuffer driver to work on more systems that have
different BIOSes as the driver no longer guesses at what the virtual BARs
mean.
I'm not entirely sure it the correct solution as I can neither test regular
VGA console nor the X's 'cyrix' video driver so there might be some breakage
there -- probably best to get some more testers before applying it.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On a Dell Latitude CPi-A I noticed a strangeness wrt. the handling of an
external monitor by the neomagic framebuffer driver, namely when the laptop is
docked in a C/Dock II with the lid shut.
A cold boot would result in the BIOS configuring the video chip to use the
"external monitor only" mode, yet neofb would default to "internal LCD only".
An attempt for a quick fix by using the Fn-F8 keystroke to toggle the display
combination modes resulted in a reproductible hard lock, powering down being
the only solution.
The attached patch makes neofb probe the register for the current display
mode, using that value as a default if nothing was specified as kernel/module
parameter.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the Intel IXDP2351 to the CS89x0 driver.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cs89x0 inconsistently used 'int' and 'u32' for device register data.
As the cs89x0 is a 16-bit chip, change the I/O accessors over to 'u16'.
(Spotted by Deepak Saxena.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stephen Hemminger