Add ACPI entry and use device_property_read to get fw value
which is common to both dtsi and acpi.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Distinguish between the case where dma information is not provided
within the DT and the case of an error during the dma init.
Exit the probe with error in case of an error during dma init.
Fixes: bb8822cbbc ("i2c: i2c-stm32: Add generic DMA API")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_new_{probed|scanned}_device will update the address after scanning.
No need to preset it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Max Staudt <max@enpas.org>
Tested-by: Max Staudt <max@enpas.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix the below warning by adding the description of clock and dev.
drivers/i2c/busses/i2c-xiic.c:57: info: Scanning doc for struct xiic_i2c
drivers/i2c/busses/i2c-xiic.c:84: warning: Function parameter or member
'dev' not described in 'xiic_i2c'
drivers/i2c/busses/i2c-xiic.c:84: warning: Function parameter or member
'clk' not described in 'xiic_i2c'
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing dma channels free calls in case of error during probe
and reorder the remove function so that dma channels are freed after
the i2c adapter is deleted.
Overall, reorder the remove function so that probe error handling order
and remove function order are same.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The IP can handle two slave addresses. One address can either be
7 bits or 10 bits while the other can only be 7 bits.
In order to ensure that a 10 bits address can always be allocated
(assuming there is only one 7 bits address already allocated),
pick up the 7-bits only address slot in priority when performing a 7-bits
address allocation.
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the following warning:
drivers/i2c/busses/i2c-stm32f7.c:315:
warning: cannot understand function prototype:
'struct stm32f7_i2c_spec i2c_specs[] =
Replace a comment starting with /** by simply /* to avoid having
it interpreted as a kernel-doc comment.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When in slave mode, an arbitration loss (ARLO) may be detected before the
slave had a chance to detect the stop condition (STOPF in ISR).
This is seen when two master + slave adapters switch their roles. It
provokes the i2c bus to be stuck, busy as SCL line is stretched.
- the I2C_SLAVE_STOP event is never generated due to STOPF flag is set but
don't generate an irq (race with ARLO irq, STOPIE is masked). STOPF flag
remains set until next master xfer (e.g. when STOPIE irq get unmasked).
In this case, completion is generated too early: immediately upon new
transfer request (then it doesn't send all data).
- Some data get stuck in TXDR register. As a consequence, the controller
stretches the SCL line: the bus gets busy until a future master transfer
triggers the bus busy / recovery mechanism (this can take time... and
may never happen at all)
So choice is to let the STOPF being detected by the slave isr handler,
to properly handle this stop condition. E.g. don't mask IRQs in error
handler, when the slave is running.
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The slave-interface documentation [1] states "the bus driver should
transmit the first byte" upon I2C_SLAVE_READ_REQUESTED slave event:
- 'val': backend returns first byte to be sent
The driver currently ignores the 1st byte to send on this event.
[1] https://www.kernel.org/doc/Documentation/i2c/slave-interface
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit abf4923e97 ("i2c: mediatek: disable zero-length transfers
for mt8183"), there is a NULL pointer dereference for all the SoCs
that don't have any quirk. mtk_i2c_functionality is not checking that
the quirks pointer is not NULL before starting to use it.
This commit add a call to i2c_check_quirks which will check whether
the quirks pointer is set, and if so will check if the IP has the
NO_ZERO_LEN quirk.
Fixes: abf4923e97 ("i2c: mediatek: disable zero-length transfers for mt8183")
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Cengiz Can <cengiz@kernel.wtf>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Ulrich Hecht <uli@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for another Intel Comet Lake variant.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for SMBus controller on Intel Jasper Lake PCH-N.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for analog filtering for i2c lines.
The sama5d2 and sam9x60 support this feature.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add new platform data support for advanced digital filtering for i2c.
The sama5d2 and sam9x60 support this feature.
This digital filter allows the user to configure the maximum
width of the spikes that can be filtered.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add new platform data support for digital filtering for i2c.
The sama5d4, sama5d2 and sam9x60 support this feature.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add new platform data support for the sam9x60 SoC
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver default behavior works with the AST2600. We need a new
compatible though to make sure the driver doesn't enable AST2400 or
AST2500 behavior.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of master pending state, it should not trigger a master
command, otherwise data could be corrupted because this H/W shares
the same data buffer for slave and master operations. It also means
that H/W command queue handling is unreliable because of the buffer
sharing issue. To fix this issue, it clears command queue if a
master command is queued in pending state to use S/W solution
instead of H/W command queue handling. Also, it refines restarting
mechanism of the pending master command.
Fixes: 2e57b7cebb ("i2c: aspeed: Add multi-master use case support")
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <taoren@fb.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit b84398d6d7 ("i2c: i801: Use iTCO version 6 in Cannon Lake PCH
and beyond") looks like to drop by accident Block Write-Block Read Process
Call support for Intel Sunrisepoint, Lewisburg, Denverton and Kaby Lake.
That support was added for above and newer platforms by the commit
315cd67c94 ("i2c: i801: Add Block Write-Block Read Process Call
support") so bring it back for above platforms.
Fixes: b84398d6d7 ("i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The NACKF flag should be cleared in INTRIICNAKI interrupt processing as
description in HW manual.
This issue shows up quickly when PREEMPT_RT is applied and a device is
probed that is not plugged in (like a touchscreen controller). The result
is endless interrupts that halt system boot.
Fixes: 310c18a414 ("i2c: riic: add driver")
Cc: stable@vger.kernel.org
Reported-by: Chien Nguyen <chien.nguyen.eb@rvc.renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We have a production-level laptop (Lenovo Yoga C630) which is exhibiting
a rather horrific bug. When I2C HID devices are being scanned for at
boot-time the QCom Geni based I2C (Serial Engine) attempts to use DMA.
When it does, the laptop reboots and the user never sees the OS.
Attempts are being made to debug the reason for the spontaneous reboot.
No luck so far, hence the requirement for this hot-fix. This workaround
will be removed once we have a viable fix.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- new driver for ICY, an Amiga Zorro card :)
- axxia driver gained slave mode support, NXP driver gained ACPI
- the slave EEPROM backend gained 16 bit address support
- and lots of regular driver updates and reworks
* 'i2c/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: tegra: Move suspend handling to NOIRQ phase
i2c: imx: ACPI support for NXP i2c controller
i2c: uniphier(-f): remove all dev_dbg()
i2c: uniphier(-f): use devm_platform_ioremap_resource()
i2c: slave-eeprom: Add comment about address handling
i2c: exynos5: Remove IRQF_ONESHOT
i2c: stm32f7: Make structure stm32f7_i2c_algo constant
i2c: cht-wc: drop check because i2c_unregister_device() is NULL safe
i2c-eeprom_slave: Add support for more eeprom models
i2c: fsi: Add of_put_node() before break
i2c: synquacer: Make synquacer_i2c_ops constant
i2c: hix5hd2: Remove IRQF_ONESHOT
i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond
watchdog: iTCO: Add support for Cannon Lake PCH iTCO
i2c: iproc: Make bcm_iproc_i2c_quirks constant
i2c: iproc: Add full name of devicetree node to adapter name
i2c: piix4: Add ACPI support
i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h
i2c: ocores: use request_any_context_irq() to register IRQ handler
i2c: designware: Fix optional reset error handling
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware support
that was removed in 2004; one doesn't want to rush these things.
- The usual assortment of fixes, typo corrections, etc.
You'll still find a handful of annoying conflicts against other trees,
mostly tied to the last RST conversions; resolutions are straightforward
and the linux-next ones are good.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl1/J4IACgkQF0NaE2wM
flhYogf9EgYozCe8RocSq+JjJpZOSFjIGDQv+GwTjOBIdqgO9tSIaY/p0wSkYKil
jYXyMDF+Xwr8podsUep2F7akBM7j9XJ+XBGJcfOna0ypC9xoejMgWt9fU3YvaWge
dQJxIQ/iwkDlKNx6uOYgKysLUWFS0EP/nzPhqBo4bZZzhugvrR46D/nQqFNmGihd
l9yLalJtP5mC0XRUv3hpdAFFFKxdC0R3BGOel2V+slSClp0LEgpdMAuMaKydEDI3
Ch9ZpIp8fB8kqONCs9/X6083WRsDOMe28KgeGrGHo4Jla6u51QBLQjSVKttFv7xk
051yNJwDWMxgl+A4gyNLDPXM7Gd7HQ==
=v4dp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.4' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It's a somewhat calmer cycle for docs this time, as the churn of the
mass RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware
support that was removed in 2004; one doesn't want to rush these
things.
- The usual assortment of fixes, typo corrections, etc"
* tag 'docs-5.4' of git://git.lwn.net/linux: (67 commits)
Documentation: kbuild: Add document about reproducible builds
docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
Documentation: Add "earlycon=sbi" to the admin guide
doc🔒 remove reference to clever use of read-write lock
devices.txt: improve entry for comedi (char major 98)
docs: mtd: Update spi nor reference driver
doc: arm64: fix grammar dtb placed in no attributes region
Documentation: sysrq: don't recommend 'S' 'U' before 'B'
mailmap: Update email address for Quentin Perret
docs: ftrace: clarify when tracing is disabled by the trace file
docs: process: fix broken link
Documentation/arm/samsung-s3c24xx: Remove stray U+FEFF character to fix title
Documentation/arm/sa1100/assabet: Fix 'make assabet_defconfig' command
Documentation/arm/sa1100: Remove some obsolete documentation
docs/zh_CN: update Chinese howto.rst for latexdocs making
Documentation: virt: Fix broken reference to virt tree's index
docs: Fix typo on pull requests guide
kernel-doc: Allow anonymous enum
Documentation: sphinx: Don't parse socket() as identifier reference
Documentation: sphinx: Add missing comma to list of strings
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
Commit acc8abcb2a ("i2c: tegra: Add suspend-resume support") added
suspend support for the Tegra I2C driver and following this change on
Tegra30 the following WARNING is seen on entering suspend ...
WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c
i2c i2c-4: Transfer while suspended
Modules linked in: brcmfmac brcmutil
CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14)
[<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8)
[<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8)
[<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c)
[<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c)
[<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4)
[<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70)
[<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30)
[<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868)
[<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec)
[<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74)
[<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54)
[<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268)
[<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c)
[<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64)
[<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4)
[<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8)
[<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4)
[<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4)
[<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8)
[<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c)
[<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48)
[<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00)
[<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c)
[<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8)
[<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4)
[<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4)
[<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184)
[<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc)
[<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xe9f21fa8 to 0xe9f21ff0)
1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000
1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228
1fe0: 00000004 be9809b8 b6f0bc0b b6e96206
The problem is that the Tegra PCIe driver indirectly uses I2C for
controlling some regulators and the I2C driver is now being suspended
before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe
driver is suspended during the NOIRQ phase and this cannot be changed
due to other dependencies. Therefore, we also need to move the suspend
handling for the Tegra I2C driver to the NOIRQ phase as well.
In order to move the I2C suspend handling to the NOIRQ phase we also
need to avoid calling pm_runtime_get/put() because per commit
1e2ef05bb8 ("PM: Limit race conditions between runtime PM and system
sleep (v2)") these cannot be called early in resume. The function
tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and
so move these calls outside of tegra_i2c_init(), so this function can
be used during the NOIRQ resume phase.
Fixes: acc8abcb2a ("i2c: tegra: Add suspend-resume support")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I have fixed various bugs, and these drivers are (I hope) pretty
stable now. Remove all dev_dbg() for code clean-up.
If I end up with debugging the drivers again, I will locally revert
this commit. I no longer need the debug code in upstream.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace the chain of platform_get_resource() and devm_ioremap_resource()
with devm_platform_ioremap_resource().
This allows to remove the local variable for (struct resource *), and
have one function call less.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The drivers sets IRQF_ONESHOT and passes only a primary handler. The IRQ
is masked while the primary is handler is invoked independently of
IRQF_ONESHOT.
With IRQF_ONESHOT the core code will not force-thread the interrupt and
this is probably not intended. I *assume* that the original author copied
the IRQ registration from another driver which passed a primary and
secondary handler and removed the secondary handler but keeping the
ONESHOT flag.
Remove IRQF_ONESHOT.
Reported-by: Benjamin Rouxel <benjamin.rouxel@uva.nl>
Tested-by: Benjamin Rouxel <benjamin.rouxel@uva.nl>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Static structure stm32f7_i2c_algo, of type i2c_algorithm, is used only
when it is assigned to constant field algo of a variable having type
i2c_adapter. As stm32f7_i2c_algo is therefore never modified, make it
const as well to protect it from unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Each iteration of for_each_available_childe_of_node puts the previous
node, but in the case of a break from the middle of the loop, there
is no put, thus causing a memory leak. Add an of_node_put before the
break.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Static structure synquacer_i2c_ops, of type i2c_adapter, is only used
when it is copied into a field of another structure. It is not itself
modified. Hence make it const to protect it from unintended
modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The drivers sets IRQF_ONESHOT and passes only a primary handler. The IRQ
is masked while the primary is handler is invoked independently of
IRQF_ONESHOT.
With IRQF_ONESHOT the core code will not force-thread the interrupt and
this is probably not intended. I *assume* that the original author copied
the IRQ registration from another driver which passed a primary and
secondary handler and removed the secondary handler but keeping the
ONESHOT flag.
Remove IRQF_ONESHOT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Cannon Lake PCH moved the NO_REBOOT bit to reside as part of the
TCO registers instead so update the i2c-i801 driver so that for Cannon
Lake and beyond register platform device for iTCO using version 6. The
affected PCHs are Cannon Lake, Cedar Fork, Comet Lake, Elkhart Lake and
Ice Lake.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Quoting from mt8183 datasheet, the number of transfers to be
transferred in one transaction should be set to bigger than 1,
so we should forbid zero-length transfer and update functionality.
Reported-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
[wsa: shortened commit message a little]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Static structure bcm_iproc_i2c_quirks, of type i2c_adapter_quirks, is
only used when being assigned to constant field quirks of a variable
having type i2c_adapter. Hence make bcm_iproc_i2c_quirks constant as
well to prevent it from unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add the full name of the devicetree node to the adapter name.
Without this change, all adapters have the same name making it difficult
to distinguish between multiple instances.
The most obvious way to see this is to use the utility i2c_detect.
e.g. "i2c-detect -l"
Before
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter
After
i2c-1 i2c Broadcom iProc (i2c@e0000) I2C adapter
i2c-0 i2c Broadcom iProc (i2c@b0000) I2C adapter
Now it is easy to figure out which adapter maps to a which DT node.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver does not support the SMBUS Quick command so remove the
flag that indicates that level of support.
By default the i2c_detect tool uses the quick command to try and
detect devices at some bus addresses. If the quick command is used
then we will not detect the device, even though it is present.
Fixes: e6e5dd3566 (i2c: iproc: Add Broadcom iProc I2C Driver)
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the i2c-piix4 SMBus controller driver to enumerate I2C slave
devices using ACPI. It builds on the related I2C mux device work
in commit 8eb5c87a92 ("i2c: add ACPI support for I2C mux ports")
In the i2c-piix4 driver the adapters are enumerated as:
Main SMBus adapter Port 0, Port 2, ..., aux port (i.e., ASF adapter)
However, in the AMD BKDG documentation[1], the implied order of ports is:
Main SMBus adapter Port 0, ASF adapter, Port 2, Port 3, ...
This ordering difference is unfortunate. We assume that ACPI
developers will use the AMD documentation ordering, so we have to
pass an extra parameter to piix4_add_adapter().
[1] 52740 BIOS and Kernel Developer's Guide (BKDG) for AMD Family 16h
Models 30h-3Fh Processors
Based on earlier work by Andrew Cooks.
Reported-by: Andrew Cooks <andrew.cooks@opengear.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Prevent bus timeouts and resets on Family 16h Model 30h by not probing
reserved Ports 3 and 4.
According to the AMD BIOS and Kernel Developer's Guides (BKDG), Port 3
and Port 4 are reserved on the following devices:
- Family 15h Model 60h-6Fh
- Family 15h Model 70h-7Fh
- Family 16h Model 30h-3Fh
Based on earlier work by Andrew Cooks.
Reported-by: Andrew Cooks <andrew.cooks@opengear.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Family 16h Model 30h SMBus controller needs the same port selection fix
as described and fixed in commit 0fe16195f8 ("i2c: piix4: Fix SMBus port
selection for AMD Family 17h chips")
commit 6befa3fde6 ("i2c: piix4: Support alternative port selection
register") also fixed the port selection for Hudson2, but unfortunately
this is not the exact same device and the AMD naming and PCI Device IDs
aren't particularly helpful here.
The SMBus port selection register is common to the following Families
and models, as documented in AMD's publicly available BIOS and Kernel
Developer Guides:
50742 - Family 15h Model 60h-6Fh (PCI_DEVICE_ID_AMD_KERNCZ_SMBUS)
55072 - Family 15h Model 70h-7Fh (PCI_DEVICE_ID_AMD_KERNCZ_SMBUS)
52740 - Family 16h Model 30h-3Fh (PCI_DEVICE_ID_AMD_HUDSON2_SMBUS)
The Hudson2 PCI Device ID (PCI_DEVICE_ID_AMD_HUDSON2_SMBUS) is shared
between Bolton FCH and Family 16h Model 30h, but the location of the
SmBus0Sel port selection bits are different:
51192 - Bolton Register Reference Guide
We distinguish between Bolton and Family 16h Model 30h using the PCI
Revision ID:
Bolton is device 0x780b, revision 0x15
Family 16h Model 30h is device 0x780b, revision 0x1F
Family 15h Model 60h and 70h are both device 0x790b, revision 0x4A.
The following additional public AMD BKDG documents were checked and do
not share the same port selection register:
42301 - Family 15h Model 00h-0Fh doesn't mention any
42300 - Family 15h Model 10h-1Fh doesn't mention any
49125 - Family 15h Model 30h-3Fh doesn't mention any
48751 - Family 16h Model 00h-0Fh uses the previously supported
index register SB800_PIIX4_PORT_IDX_ALT at 0x2e
Signed-off-by: Andrew Cooks <andrew.cooks@opengear.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org [v4.6+]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-ocores device is an HDL component that get instantiated in FPGA.
The software stack used to drive an FPGA can be very different, and the
i2c-ocore ip-core must work in different context. With respect to this
patch the IRQ controller behind this device, and its driver, can have
different implementations (nested threads). For this reason, it is safer
to use `request_any_context_irq()` to avoid errors at probe time.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit bb475230b8 ("reset: make optional functions really optional")
brought a missed part of the support for an optional reset handlers.
Since that we don't need to have special error handling in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit c62ebb3d5f ("i2c: designware: Add support for an interface clock")
introduced an optional clock while missed correct error handling.
assert reset line back if error happen at ->probe().
Fixes: c62ebb3d5f ("i2c: designware: Add support for an interface clock")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Static structure tsl2550_info, of type i2c_board_info, is referenced
only twice: the first time in arguments to dev_info() (which does not
modify it) and the second time as the last argument to function
i2c_new_device() (where the corresponding parameter is declared as
const). As tsl2550_info is therefore never modified, make it const to
protect it from unintended modifications.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for Intel(R) Programmable Services Engine (Intel(R) PSE) I2C
controller in Intel Elkhart Lake when interface is assigned to the host
processor.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some devices support MSI interrupts. Let's at least try to use them in
platforms that provide MSI capability.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This device contains both master and slave controllers which can be
enabled simultaneously. Both controllers share the same SDA/SCL lines
and interrupt source but has separate control and status registers.
Controllers also works in loopback mode - slave device can communicate
with its own master controller internally. The controller can handle up
to two addresses, both of which may be 10 bit. Most of the logic
(sending (N)ACK, handling repeated start or switching between
write/read) is handled automatically which makes working with this
controller quite easy.
For simplicity, this patch adds basic support, limiting to only one
slave address. Support for the 2nd device may be added in the future.
Note that synchronize_irq() is used to ensure any running slave interrupt
is finished to make sure slave i2c_client structure can be safely used
by i2c_slave_event.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since the 2019 a1k.org community re-print of these PCBs sports an
LTC2990 hwmon chip as an example use case, let this driver autoprobe
for that as well. If it is present, modprobing ltc2990 is sufficient.
The property_entry enables the three additional inputs available on
this particular board:
in1 will be the voltage of the 5V rail, divided by 2.
in2 will be the voltage of the 12V rail, divided by 4.
temp3 will be measured using a PCB loop next the chip.
Signed-off-by: Max Staudt <max@enpas.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is the i2c-icy driver for the ICY board for Amiga computers.
It connects a PCF8584 I2C controller to the Zorro bus, providing I2C
connectivity. The original documentation can be found on Aminet:
https://aminet.net/package/docs/hard/icy
IRQ support is currently not implemented, as i2c-algo-pcf is built for
the ISA bus and a straight implementation of the same stack locks up a
Zorro machine.
Signed-off-by: Max Staudt <max@enpas.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
[wsa: added a missing newline reported by checkpatch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Inspired by Lori Hikichi's patch for iproc, this adds the full name of
the devicetree node to the adapter name. With the introduction of
BCM2711 it's very difficult to distinguish between the multiple instances.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C block on the BCM2711 isn't affected by the clk stretching bug.
So there is no need to apply the corresponding quirk.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure interrupt handler i2c_dw_irq_handler_slave() has finished
before clearing the the dev->slave pointer in i2c_dw_unreg_slave().
There is possibility for a race if i2c_dw_irq_handler_slave() is running
on another CPU while clearing the dev->slave pointer.
Reported-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
check_acpi_smo88xx_device() utilizes acpi_get_object_info() which in its turn
allocates a buffer. User is responsible to clean allocated resources. The last
has been missed in the original code. Fix it here.
While here, replace !ACPI_SUCCESS() with ACPI_FAILURE().
Fixes: 19b07cb4a1 ("i2c: i801: Register optional lis3lv02d I2C device on Dell machines")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are three families of IOP machines we support in Linux: iop32x
(which includes EP80219), iop33x and iop13xx (aka IOP34x aka WP8134x).
All products we support in the kernel are based on the first of these,
iop32x, the other families only ever supported the Intel reference
boards but no actual machine anyone could ever buy.
While one could clearly make them all three work in a single kernel
with some work, this takes the easy way out, removing the later two
platforms entirely, under the assumption that there are no remaining
users.
Earlier versions of OpenWRT and Debian both had support for iop32x
but not the others, and they both dropped iop32x as well in their 2015
releases.
Link: https://lore.kernel.org/r/20190809163334.489360-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C parts
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When the kernel is build with lockdep support and the i2c-cht-wc driver is
used, the following warning is shown:
[ 66.674334] ======================================================
[ 66.674337] WARNING: possible circular locking dependency detected
[ 66.674340] 5.3.0-rc4+ #83 Not tainted
[ 66.674342] ------------------------------------------------------
[ 66.674345] systemd-udevd/1232 is trying to acquire lock:
[ 66.674349] 00000000a74dab07 (intel_soc_pmic_chtwc:167:(&cht_wc_regmap_cfg)->lock){+.+.}, at: regmap_write+0x31/0x70
[ 66.674360]
but task is already holding lock:
[ 66.674362] 00000000d44a85b7 (i2c_register_adapter){+.+.}, at: i2c_smbus_xfer+0x49/0xf0
[ 66.674370]
which lock already depends on the new lock.
[ 66.674371]
the existing dependency chain (in reverse order) is:
[ 66.674374]
-> #1 (i2c_register_adapter){+.+.}:
[ 66.674381] rt_mutex_lock_nested+0x46/0x60
[ 66.674384] i2c_smbus_xfer+0x49/0xf0
[ 66.674387] i2c_smbus_read_byte_data+0x45/0x70
[ 66.674391] cht_wc_byte_reg_read+0x35/0x50
[ 66.674394] _regmap_read+0x63/0x1a0
[ 66.674396] _regmap_update_bits+0xa8/0xe0
[ 66.674399] regmap_update_bits_base+0x63/0xa0
[ 66.674403] regmap_irq_update_bits.isra.0+0x3b/0x50
[ 66.674406] regmap_add_irq_chip+0x592/0x7a0
[ 66.674409] devm_regmap_add_irq_chip+0x89/0xed
[ 66.674412] cht_wc_probe+0x102/0x158
[ 66.674415] i2c_device_probe+0x95/0x250
[ 66.674419] really_probe+0xf3/0x380
[ 66.674422] driver_probe_device+0x59/0xd0
[ 66.674425] device_driver_attach+0x53/0x60
[ 66.674428] __driver_attach+0x92/0x150
[ 66.674431] bus_for_each_dev+0x7d/0xc0
[ 66.674434] bus_add_driver+0x14d/0x1f0
[ 66.674437] driver_register+0x6d/0xb0
[ 66.674440] i2c_register_driver+0x45/0x80
[ 66.674445] do_one_initcall+0x60/0x2f4
[ 66.674450] kernel_init_freeable+0x20d/0x2b4
[ 66.674453] kernel_init+0xa/0x10c
[ 66.674457] ret_from_fork+0x3a/0x50
[ 66.674459]
-> #0 (intel_soc_pmic_chtwc:167:(&cht_wc_regmap_cfg)->lock){+.+.}:
[ 66.674465] __lock_acquire+0xe07/0x1930
[ 66.674468] lock_acquire+0x9d/0x1a0
[ 66.674472] __mutex_lock+0xa8/0x9a0
[ 66.674474] regmap_write+0x31/0x70
[ 66.674480] cht_wc_i2c_adap_smbus_xfer+0x72/0x240 [i2c_cht_wc]
[ 66.674483] __i2c_smbus_xfer+0x1a3/0x640
[ 66.674486] i2c_smbus_xfer+0x67/0xf0
[ 66.674489] i2c_smbus_read_byte_data+0x45/0x70
[ 66.674494] bq24190_probe+0x26b/0x410 [bq24190_charger]
[ 66.674497] i2c_device_probe+0x189/0x250
[ 66.674500] really_probe+0xf3/0x380
[ 66.674503] driver_probe_device+0x59/0xd0
[ 66.674506] device_driver_attach+0x53/0x60
[ 66.674509] __driver_attach+0x92/0x150
[ 66.674512] bus_for_each_dev+0x7d/0xc0
[ 66.674515] bus_add_driver+0x14d/0x1f0
[ 66.674518] driver_register+0x6d/0xb0
[ 66.674521] i2c_register_driver+0x45/0x80
[ 66.674524] do_one_initcall+0x60/0x2f4
[ 66.674528] do_init_module+0x5c/0x230
[ 66.674531] load_module+0x2707/0x2a20
[ 66.674534] __do_sys_init_module+0x188/0x1b0
[ 66.674537] do_syscall_64+0x5c/0xb0
[ 66.674541] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 66.674543]
other info that might help us debug this:
[ 66.674545] Possible unsafe locking scenario:
[ 66.674547] CPU0 CPU1
[ 66.674548] ---- ----
[ 66.674550] lock(i2c_register_adapter);
[ 66.674553] lock(intel_soc_pmic_chtwc:167:(&cht_wc_regmap_cfg)->lock);
[ 66.674556] lock(i2c_register_adapter);
[ 66.674559] lock(intel_soc_pmic_chtwc:167:(&cht_wc_regmap_cfg)->lock);
[ 66.674561]
*** DEADLOCK ***
The problem is that the CHT Whiskey Cove PMIC's builtin i2c-adapter is
itself a part of an i2c-client (the PMIC). This means that transfers done
through it take adapter->bus_lock twice, once for the parent i2c-adapter
and once for its own bus_lock. Lockdep does not like this nested locking.
To make lockdep happy in the case of busses with muxes, the i2c-core's
i2c_adapter_lock_bus function calls:
rt_mutex_lock_nested(&adapter->bus_lock, i2c_adapter_depth(adapter));
But i2c_adapter_depth only works when the direct parent of the adapter is
another adapter, as it is only meant for muxes. In this case there is an
i2c-client and MFD instantiated platform_device in the parent->child chain
between the 2 devices.
This commit overrides the default i2c_lock_operations, passing a hardcoded
depth of 1 to rt_mutex_lock_nested, making lockdep happy.
Note that if there were to be a mux attached to the i2c-wc-cht adapter,
this would break things again since the i2c-mux code expects the
root-adapter to have a locking depth of 0. But the i2c-wc-cht adapter
always has only 1 client directly attached in the form of the charger IC
paired with the CHT Whiskey Cove PMIC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch corrects the SPDX License Identifier style
in header file related to STM32 Driver for I2C hardware
bus support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After we disabled interrupts, there might still be an active one
running. Sync before clearing the pointer to the slave device.
Fixes: c31d0a0002 ("i2c: emev2: add slave support")
Reported-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After we disabled interrupts, there might still be an active one
running. Sync before clearing the pointer to the slave device.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Reported-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit e1ab9a468e ("i2c: imx: improve the error handling in
i2c_imx_dma_request()") when booting with the DMA driver as module (such
as CONFIG_FSL_EDMA=m) the following endless clk warnings are seen:
[ 153.077831] ------------[ cut here ]------------
[ 153.082528] WARNING: CPU: 0 PID: 15 at drivers/clk/clk.c:924 clk_core_disable_lock+0x18/0x24
[ 153.093077] i2c0 already disabled
[ 153.096416] Modules linked in:
[ 153.099521] CPU: 0 PID: 15 Comm: kworker/0:1 Tainted: G W 5.2.0+ #321
[ 153.107290] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[ 153.113772] Workqueue: events deferred_probe_work_func
[ 153.118979] [<c0019560>] (unwind_backtrace) from [<c0014734>] (show_stack+0x10/0x14)
[ 153.126778] [<c0014734>] (show_stack) from [<c083f8dc>] (dump_stack+0x9c/0xd4)
[ 153.134051] [<c083f8dc>] (dump_stack) from [<c0031154>] (__warn+0xf8/0x124)
[ 153.141056] [<c0031154>] (__warn) from [<c0031248>] (warn_slowpath_fmt+0x38/0x48)
[ 153.148580] [<c0031248>] (warn_slowpath_fmt) from [<c040fde0>] (clk_core_disable_lock+0x18/0x24)
[ 153.157413] [<c040fde0>] (clk_core_disable_lock) from [<c058f520>] (i2c_imx_probe+0x554/0x6ec)
[ 153.166076] [<c058f520>] (i2c_imx_probe) from [<c04b9178>] (platform_drv_probe+0x48/0x98)
[ 153.174297] [<c04b9178>] (platform_drv_probe) from [<c04b7298>] (really_probe+0x1d8/0x2c0)
[ 153.182605] [<c04b7298>] (really_probe) from [<c04b7554>] (driver_probe_device+0x5c/0x174)
[ 153.190909] [<c04b7554>] (driver_probe_device) from [<c04b58c8>] (bus_for_each_drv+0x44/0x8c)
[ 153.199480] [<c04b58c8>] (bus_for_each_drv) from [<c04b746c>] (__device_attach+0xa0/0x108)
[ 153.207782] [<c04b746c>] (__device_attach) from [<c04b65a4>] (bus_probe_device+0x88/0x90)
[ 153.215999] [<c04b65a4>] (bus_probe_device) from [<c04b6a04>] (deferred_probe_work_func+0x60/0x90)
[ 153.225003] [<c04b6a04>] (deferred_probe_work_func) from [<c004f190>] (process_one_work+0x204/0x634)
[ 153.234178] [<c004f190>] (process_one_work) from [<c004f618>] (worker_thread+0x20/0x484)
[ 153.242315] [<c004f618>] (worker_thread) from [<c0055c2c>] (kthread+0x118/0x150)
[ 153.249758] [<c0055c2c>] (kthread) from [<c00090b4>] (ret_from_fork+0x14/0x20)
[ 153.257006] Exception stack(0xdde43fb0 to 0xdde43ff8)
[ 153.262095] 3fa0: 00000000 00000000 00000000 00000000
[ 153.270306] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 153.278520] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 153.285159] irq event stamp: 3323022
[ 153.288787] hardirqs last enabled at (3323021): [<c0861c4c>] _raw_spin_unlock_irq+0x24/0x2c
[ 153.297261] hardirqs last disabled at (3323022): [<c040d7a0>] clk_enable_lock+0x10/0x124
[ 153.305392] softirqs last enabled at (3322092): [<c000a504>] __do_softirq+0x344/0x540
[ 153.313352] softirqs last disabled at (3322081): [<c00385c0>] irq_exit+0x10c/0x128
[ 153.320946] ---[ end trace a506731ccd9bd703 ]---
This endless clk warnings behaviour is well explained by Andrey Smirnov:
"Allocating DMA after registering I2C adapter can lead to infinite
probing loop, for example, consider the following scenario:
1. i2c_imx_probe() is called and successfully registers an I2C
adapter via i2c_add_numbered_adapter()
2. As a part of i2c_add_numbered_adapter() new I2C slave devices
are added from DT which results in a call to
driver_deferred_probe_trigger()
3. i2c_imx_probe() continues and calls i2c_imx_dma_request() which
due to lack of proper DMA driver returns -EPROBE_DEFER
4. i2c_imx_probe() fails, removes I2C adapter and returns
-EPROBE_DEFER, which places it into deferred probe list
5. Deferred probe work triggered in #2 above kicks in and calls
i2c_imx_probe() again thus bringing us to step #1"
So revert commit e1ab9a468e ("i2c: imx: improve the error handling in
i2c_imx_dma_request()") and restore the old behaviour, in order to
avoid regressions on existing setups.
Cc: <stable@vger.kernel.org>
Reported-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: e1ab9a468e ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The 'enable' clock of I2C master is required, we should return an error
if failed to get the 'enable' clock, to make sure the I2C driver can be
defer probe if the clock resource is not ready.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now there is no need to keep our I2C driver to be initialized so early,
thus changing to module level and let it can be built as a module,
meanwhile adding some module information.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
drivers/i2c/busses/i2c-designware-master.c: In function ‘i2c_dw_init_recovery_info’:
drivers/i2c/busses/i2c-designware-master.c:658:6: warning: unused variable ‘r’ [-Wunused-variable]
int r;
^
Fixes: 33eb09a02e ("i2c: designware: make use of devm_gpiod_get_optional")
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/i2c/busses/i2c-s3c2410.c: In function 'i2c_s3c_irq_nextbyte':
drivers/i2c/busses/i2c-s3c2410.c:431:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (i2c->state == STATE_READ)
^
drivers/i2c/busses/i2c-s3c2410.c:439:2: note: here
case STATE_WRITE:
^~~~
Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In SAMA5D2 datasheet, TWIHS_CWGR register rescription mentions clock
offset of 3 cycles (compared to 4 in eg. SAMA5D3).
Cc: stable@vger.kernel.org # 5.2.x
[needs applying to i2c-at91.c instead for earlier kernels]
Fixes: 0ef6f3213d ("i2c: at91: add support for new alternative command mode")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver was not disabling TXRDY interrupt after last TX byte.
This caused interrupt storm until transfer timeouts for slow
or broken device on the bus. The patch fixes the interrupt storm
on my SAMA5D2-based board.
Cc: stable@vger.kernel.org # 5.2.x
[v5.2 introduced file split; the patch should apply to i2c-at91.c before the split]
Fixes: fac368a040 ("i2c: at91: add new driver")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tested-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a semantical change: if devm_gpiod_get_optional returns -ENOSYS
this is passed as error to the caller. This effectively reverts commit
d1fa74520d ("i2c: designware: Consider SCL GPIO optional") which
shouldn't be necessary any more since gpiod_get_optional doesn't return
-ENOSYS any more with GPIOLIB=n.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In commit 518a2f1925 ("dma-mapping: zero memory returned from
dma_alloc_*"), dma_alloc_coherent has already zeroed the memory. So
memset is not needed.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C driver fails to probe if CONFIG_PM_SLEEP=n because runtime PM
doesn't depend on the PM sleep and in this case the runtime PM ops are
not included in the driver, resulting in I2C clock not being enabled.
It's much cleaner to simply allow compiler to remove the dead code
instead of messing with the #ifdefs.
This patch fixes such errors when CONFIG_PM_SLEEP=n:
tegra-i2c 7000c400.i2c: timeout waiting for fifo flush
tegra-i2c 7000c400.i2c: Failed to initialize i2c controller
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use SMBUS_MASTER_DATA_READ.MASTER_RD_STATUS bit to check for RX
FIFO empty condition because SMBUS_MASTER_FIFO_CONTROL.MASTER_RX_PKT_COUNT
is not updated for read >= 64 bytes. This fixes the issue when trying to
read from the I2C slave more than 63 bytes.
Fixes: c24b8d574b ("i2c: iproc: Extend I2C read up to 255 bytes")
Cc: stable@kernel.org
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Convert each file at I2C subsystem, renaming them to .rst and
adding to the driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a generic helper to match any/all devices. Using this
introduce new wrappers {bus/driver/class}_find_next_device().
Cc: Elie Morisse <syniurge@gmail.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI
Link: https://lore.kernel.org/r/20190723221838.12024-7-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some files got renamed but probably due to some merge conflicts,
a few references still point to the old locations.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pull i2c updates from Wolfram Sang:
"New stuff from the I2C world:
- in the core, getting irqs from ACPI is now similar to OF
- new driver for MediaTek MT7621/7628/7688 SoCs
- bcm2835, i801, and tegra drivers got some more attention
- GPIO API cleanups
- cleanups in the core headers
- lots of usual driver updates"
* 'i2c/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (74 commits)
i2c: mt7621: Fix platform_no_drv_owner.cocci warnings
i2c: cpm: remove casting dma_alloc
dt-bindings: i2c: sun6i-p2wi: Fix the binding example
dt-bindings: i2c: mv64xxx: Fix the example compatible
i2c: i801: Documentation update
i2c: i801: Add support for Intel Tiger Lake
i2c: i801: Fix PCI ID sorting
dt-bindings: i2c-stm32: document optional dmas
i2c: i2c-stm32f7: Add I2C_SMBUS_I2C_BLOCK_DATA support
i2c: core: Tidy up handling of init_irq
i2c: core: Move ACPI gpio IRQ handling into i2c_acpi_get_irq
i2c: core: Move ACPI IRQ handling to probe time
i2c: acpi: Factor out getting the IRQ from ACPI
i2c: acpi: Use available IRQ helper functions
i2c: core: Allow whole core to use i2c_dev_irq_from_resources
eeprom: at24: modify a comment referring to platform data
dt-bindings: i2c: omap: Add new compatible for J721E SoCs
dt-bindings: i2c: mv64xxx: Add YAML schemas
dt-bindings: i2c: sun6i-p2wi: Add YAML schemas
i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver
...
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add SMBUS PCI ID for Intel Tiger Lake -LP.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I managed to break sorting in PCI ID defines in my last two patches:
commit 5cd1c56c42 ("i2c: i801: Add support for Intel Comet Lake")
commit 9be1485acc ("i2c: i801: Add support for Intel Elkhart Lake")
Fix them up.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the support of I2C_SMBUS_I2C_BLOCK_DATA transaction type
for the stm32f7 SMBUS Controller.
Use emulated I2C_SMBUS_I2C_BLOCK_DATA transactions as there is no specific
hardware in STM32 I2C to manage this (e.g. like no need for PEC here).
Emulated transfer will fall back calling i2c transfer method where there's
already support for DMAs for example.
So, use the I2C_FUNC_SMBUS_I2C_BLOCK in stm32f7_i2c_func(), and rely on
emulated transfer by returning -EOPNOTSUPP in the smbus_xfer() routine
for such a case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I realize that there are changes in drivers/i2c/busses/i2c-i801.c that strictly
speaking don't belong here, but I hope you don't mind. These changes are all
about the interaction with the i2c-mux-gpio code, and I did a test-merge a few
days ago w/o conflicts.
Anyway, the GPIO-work from Linus Walleij (with help from Serge Semin) in the
i2c-mux-gpio and i2c-arb-gpio-challenge drivers is the main feature.
This patch adds a driver for the I2C controller found on the MediaTek
MT7621/7628/7688 SoC's. The base version of this driver was done by
Steven Liu (according to the copyright and MODULE_AUTHOR lines). It
can be found in the OpenWRT repositories (v4.14 at the time I looked).
The base driver had many issues, which are disccussed here:
https://en.forum.labs.mediatek.com/t/openwrt-15-05-loads-non-working-i2c-kernel-module-for-mt7688/1286/3
>From this link an enhanced driver version (complete rewrite, mayor
changes: support clock stretching, repeated start, ACK handling and
unlimited message length) from Jan Breuer can be found here:
https://gist.github.com/j123b567/9b555b635c2b4069d716b24198546954
This patch now adds this enhanced I2C driver to mainline.
Changes by Stefan Roese for upstreaming:
- Add devicetree bindings
- checkpatch clean
- Use module_platform_driver()
- Minor cosmetic enhancements
- Removed IO warpped functions
- Use readl_relaxed_poll_timeout() and drop poll_down_timeout()
- Removed superfluous barrier() in mtk_i2c_reset()
- Use i2c_8bit_addr_from_msg()
- Added I2C_FUNC_PROTOCOL_MANGLING
- Removed adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Probe function fails to recognize that upstream clock actually
doesn't yet exist because clock driver has not been initialized.
Actually try to go get the clock and test for its existence
before trying to set up a downstream clock based upon it.
This fixes a bug that causes the i2c driver not to work with
monolithic kernels.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If any of the clock code in the probe fails and returns, the IRQ
will not be freed. Moving the IRQ request to last allows it to
be freed on any errors further up in the probe function. devm_
calls can apparently not be used because there are some potential
race conditions that will arise.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver_find_device() accepts a match function pointer to
filter the devices for lookup, similar to bus/class_find_device().
However, there is a minor difference in the prototype for the
match parameter for driver_find_device() with the now unified
version accepted by {bus/class}_find_device(), where it doesn't
accept a "const" qualifier for the data argument. This prevents
us from reusing the generic match functions for driver_find_device().
For this reason, change the prototype of the driver_find_device() to
make the "match" parameter in line with {bus/class}_find_device()
and adjust its callers to use the const qualifier. Also, we could
now promote the "data" parameter to const as we pass it down
as a const parameter to the match functions.
Cc: Corey Minyard <minyard@acm.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This switches the i801 GPIO mux to use GPIO descriptors for
handling the GPIO lines. The previous hack which was reaching
inside the GPIO chips etc cannot live on. We pass descriptors
along with the GPIO mux device at creation instead.
The GPIO mux was only used by way of platform data with a
platform device from one place in the kernel: the i801 i2c bus
driver. Let's just associate the GPIO descriptor table with
the actual device like everyone else and dynamically create
a descriptor table passed along with the GPIO i2c mux.
This enables simplification of the GPIO i2c mux driver to
use only the descriptor API and the OF probe path gets
simplified in the process.
The i801 driver was registering the GPIO i2c mux with
PLATFORM_DEVID_AUTO which would make it hard to predict the
device name and assign the descriptor table properly, but
this seems to be a mistake to begin with: all of the
GPIO mux devices are hardcoded to look up GPIO lines from
the "gpio_ich" GPIO chip. If there are more than one mux,
there is certainly more than one gpio chip as well, and
then we have more serious problems. Switch to
PLATFORM_DEVID_NONE instead. There can be only one.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Jean Delvare <jdelvare@suse.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[Removed a newline, suggested by Andy. /Peter]
Signed-off-by: Peter Rosin <peda@axentia.se>
The usage of BUG() macro is generally discouraged in kernel, unless
it's a problem that results in a physical damage or loss of data.
This patch removes unnecessary BUG() macros and replaces the rest
with warning.
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add PCI ID for Intel Elkhart Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During probe, return the "get_irq" error value instead of -EINVAL which
allows the driver to be deferred probed if needed.
Fix also the case where of_irq_get() returns a negative value.
Note :
On failure of_irq_get() returns 0 or a negative value while
platform_get_irq() returns a negative value.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license gpl v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081202.146070292@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 53 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.904365654@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 6 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.720704315@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a match table to allow automatic probing of ACPI device
QCOM0220. Ignore clock attainment errors. Set default clock
frequency value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Qualcomm Geni I2C driver currently probes silently which can be
confusing when debugging potential issues. Add a low level (INFO)
print when each I2C controller is successfully initially set-up.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Post suspend I2C registers have power on reset values. Before any
transfer initialize I2C registers to prevent I2C transfer timeout
and implement suspend and resume callbacks needed. Fix below errors
post suspend:
1) Tegra I2C transfer timeout during jetson tx2 resume:
[ 27.520613] pca953x 1-0074: calling pca953x_resume+0x0/0x1b0 @ 2939, parent: i2c-1
[ 27.633623] tegra-i2c 3160000.i2c: i2c transfer timed out
[ 27.639162] pca953x 1-0074: Unable to sync registers 0x3-0x5. -110
[ 27.645336] pca953x 1-0074: Failed to sync GPIO dir registers: -110
[ 27.651596] PM: dpm_run_callback(): pca953x_resume+0x0/0x1b0 returns -110
[ 27.658375] pca953x 1-0074: pca953x_resume+0x0/0x1b0 returned -110 after 127152 usecs
[ 27.666194] PM: Device 1-0074 failed to resume: error -110
2) Tegra I2C transfer timeout error on jetson Xavier post resume.
Remove i2c bus lock-unlock calls in resume callback as i2c_mark_adapter_*
(suspended-resumed) help ensure i2c core calls from client are not
executed before i2c-tegra resume.
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-ocore driver already has a polling mode interface.But it needs
a workaround for FU540 Chipset on HiFive unleashed board (RevA00).
There is an erratum in FU540 chip that prevents interrupt driven i2c
transfers from working, and also the I2C controller's interrupt bit
cannot be cleared if set, due to this the existing i2c polling mode
interface added in mainline earlier doesn't work, and CPU stall's
infinitely, when-ever i2c transfer is initiated.
Ref:
commit dd7dbf0eb0 ("i2c: ocores: refactor setup for polling")
The workaround / fix under OCORES_FLAG_BROKEN_IRQ is particularly for
FU540-COOO SoC.
The polling function identifies a SiFive device based on the device node
and enables the workaround.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update device id table for Opencore's I2C master based re-implementation
used in FU540-c000 chipset on HiFive Unleashed platform.
Device ID's include Sifive, soc-specific device for chip specific tweaks
and sifive IP block specific device for generic programming model.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver defers probe because of a missing clock, avoid outputting
an error message. The clock will show up eventually.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit
19b07cb4a1 ("i2c: i801: Register optional lis3lv02d I2C device on Dell machines")
introduced a new check in order to enumerate some slave devices on Dell
machines. Though, it brings a regression on machines where DMI vendor is not set.
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 8 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc4-next-20190613+ #317
RIP: 0010:strcmp+0xc/0x20
To fix this crash, check if vendor field is present before accessing to it.
Fixes: 19b07cb4a1 ("i2c: i801: Register optional lis3lv02d I2C device on Dell machines")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The IOP3xx has some elaborate code to directly slam the
GPIO lines multiplexed with I2C down low before enablement,
apparently a workaround for a hardware bug found in the
early chips.
After consulting the developer documentation for IOP80321
and IOP80331 I can clearly see that this may be useful for
IOP80321 family (mach-iop32x) but it is highly dubious for
any 80331 series or later chip: in these chips the lines
are not multiplexed for UARTs.
We convert the code to pass optional GPIO descriptors
and register these only on the 80321-based boards where
it makes sense, optionally obtain them in the driver and
use the gpiod_set_raw_value() to ascertain the line gets
driven low when needed.
The GPIO driver does not give the GPIO chip a reasonable
label so the patch also adds that so that these machine
descriptor tables can be used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The S3C2410 does some funny dance around its pins:
- First try to call back to the platform to get and control
some GPIO pins
- If this doesn't work, it tries to get a pin control handle
- If this doesn't work, it retrieves two GPIOs from the device
tree node and does nothing with them
If we're gonna retrieve two GPIOs and do nothing with them, we
might as well do it using the GPIO descriptor API. When we use
the resource management API, the code gets smaller.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The devm_gpiod_request_gpiod() call will add "-gpios" to
any passed connection ID before looking it up.
I do not think the reset GPIO on this platform is named
"reset-gpios-gpios" but rather "reset-gpios" in the device
tree, so fix this up so that we get a proper reset GPIO
handle.
Also drop the inclusion of the legacy GPIO header.
Fixes: 0e8ce93bdc ("i2c: pca-platform: add devicetree awareness")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Model the I2C bus clock divider as a part of the Core Clock Framework.
Primarily this removes the clk_get_rate() call from each transfer.
This call causes problems for slave drivers that themselves have
internal clock components that are controlled by an I2C interface.
When the slave's internal clock component is prepared, the prepare
lock is obtained, and it makes calls to the I2C subsystem to
command the hardware to activate the clock. In order to perform
the I2C transfer, this driver sets the divider, which requires
it to get the parent clock rate, which it does with clk_get_rate().
Unfortunately, this function will try to take the clock prepare
lock, which is already held by the slave's internal clock calls
creating a deadlock.
Modeling the divider in the CCF natively removes this dependency
and the divider value is only set upon changing the bus clock
frequency or changes in the parent clock that cascade down to this
divisor. This obviates the need to set the divider with every
transfer and avoids the deadlock described above. It also should
provide better clock debugging and save a few cycles on each
transfer due to not having to recalcuate the divider value.
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix checkpatch.pl WARNING for delay of approximately 1msec
in flush i2c FIFO polling loop by using usleep_range(1000, 2000):
WARNING: msleep < 20ms can sleep for up to 20ms; see ...
Documentation/timers/timers-howto.txt
+ msleep(1);
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix checkpatch.pl alignment and blank line check(s) in i2c-tegra.c
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove variable initializations in functions that
are followed by assignments before use
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Acorn i2c driver (for RiscPC) triggers the "i2c adapter has no name"
warning in the I2C core driver, resulting in the RTC being inaccessible.
Fix this.
Fixes: 2236baa75f ("i2c: Sanity checks on adapter registration")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuGTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykBvQCg2SG+HmDH+tlwKLT/q7jZcLMPQigAoMpt9Uuy
sxVEiFZo8ZU9v1IoRb1I
=qU++
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
This driver does not support reading more than 255 bytes at once because
the register for storing the number of bytes to read is only 8 bits. Add
a max_read_len quirk to enforce this.
This was found when using this driver with the SFP driver, which was
previously reading all 256 bytes in the SFP EEPROM in one transaction.
This caused a bunch of hard-to-debug errors in the xiic driver since the
driver/logic was treating the number of bytes to read as zero.
Rejecting transactions that aren't supported at least allows the problem
to be diagnosed more easily.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Currently we only create an I2C bus for the ports listed in the
device-tree for that master. There's no real reason for this since
we can discover the number of ports the master supports by looking
at the port_max field of the status register.
This patch re-works the bus add logic so that we always create buses
for each port, unless the bus is marked as unavailable in the DT. This
is useful since it ensures that all the buses provided by the CFAM I2C
master are accessible to debug tools.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Dell platform team told us that some (DMI whitelisted) Dell Latitude
machines have ST microelectronics accelerometer at I2C address 0x29.
Presence of that ST microelectronics accelerometer is verified by existence
of SMO88xx ACPI device which represent that accelerometer. Unfortunately
ACPI device does not specify I2C address.
This patch registers lis3lv02d device for selected Dell Latitude machines
at I2C address 0x29 after detection. And for Dell Vostro V131 machine at
I2C address 0x1d which was manually detected.
Finally commit a7ae81952c ("i2c: i801: Allow ACPI SystemIO OpRegion to
conflict with PCI BAR") allowed to use i2c-i801 driver on Dell machines so
lis3lv02d correctly initialize accelerometer.
Tested on Dell Latitude E6440.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cypress USB Type-C CCGx controller firmware version 3.1.10
(which is being used in many NVIDIA GPU cards) has known issue of
not triggering interrupt when a USB device is hot plugged to runtime
resume the controller. If any GPU card gets latest kernel with runtime
pm support but does not get latest fixed firmware then also it should
continue to work and therefore a workaround is required to check for
any connector change event
The workaround is to request runtime resume of i2c client
which is UCSI Cypress CCGx driver. CCG driver will call the ISR
for any connector change event only if NVIDIA GPU has old
CCG firmware with the known issue.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable runtime pm support with autosuspend delay of three second.
This is to make sure I2C client device Cypress CCGx has completed
all transaction.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added a local variable "send_stop" to simplify "goto" statements.
The "send_stop" handles below two case
1) When first i2c start fails and so i2c stop is not sent before
exiting
2) When i2c stop failed after all transfers and we do not need to
send another stop before exiting.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Based on 1 normalized pattern(s):
this file is released under the gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 68 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.292346262@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.435762997@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license 2 as published
by the free software foundation this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation this program is distributed in the hope
that it [would] be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.804956444@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 this program is distributed
in the hope that it will be useful but without any warranty without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 97 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.025053186@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull i2c fixes from Wolfram Sang:
"A memleak fix for the core, two driver bugfixes, as well as fixing
missing file patterns to MAINTAINERS"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add I2C DT bindings to ARM platforms
MAINTAINERS: add DT bindings to i2c drivers
i2c: synquacer: fix synquacer_i2c_doxfer() return value
i2c: mlxcpld: Fix wrong initialization order in probe
i2c: dev: fix potential memory leak in i2cdev_ioctl_rdwr
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100844.561472061@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on MACH_JZ4780 prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
master_xfer should return the number of messages successfully
processed.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Okamoto Satoru <okamoto.satoru@socionext.com>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ARCH_BRCMSTB platforms have the BCM2835 I2C controllers, allow
selecting the i2c-bcm2835 driver on such platforms.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use __maybe_unused for runtime PM related functions instead
of #if CONFIG_PM to simply the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix wrong order in probing routine initialization - field `base_addr'
is used before it's initialized. Move assignment of 'priv->base_addr`
to the beginning, prior the call to mlxcpld_i2c_read_comm().
Wrong order caused the first read of capability register to be executed
at wrong offset 0x0 instead of 0x2000. By chance it was a "good
garbage" at 0x0 offset.
Fixes: 313ce648b5 ("i2c: mlxcpld: Add support for extended transaction length for i2c-mlxcpld")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091650.663497195@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
derived from gplv2+ licensed source [copyright] [c] [2008]
[wondermedia] [technologies] [inc] this program is free software you
can redistribute it and or modify it under the terms of the gnu
general public license version 2 or at your option any later version
as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071900.028616342@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.961286471@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull i2c updates from Wolfram Sang:
- API for late atomic transfers (e.g. to shut down via PMIC). We have a
seperate callback now which is called under clearly defined
conditions. In-kernel users are converted, too.
- new driver for the AMD PCIe MP2 I2C controller
- large refactoring for at91 and bcm-iproc (both gain slave support due
to this)
- and a good share of various driver improvements anf fixes
* 'i2c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (57 commits)
dt-bindings: i2c: riic: document r7s9210 support
i2c: imx-lpi2c: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
i2c-piix4: Add Hygon Dhyana SMBus support
i2c: core: apply 'is_suspended' check for SMBus, too
i2c: core: ratelimit 'transfer when suspended' errors
i2c: iproc: Change driver to use 'BIT' macro
i2c: riic: Add Runtime PM support
i2c: mux: demux-pinctrl: use struct_size() in devm_kzalloc()
i2c: mux: pca954x: allow management of device idle state via sysfs
i2c: mux: pca9541: remove support for unused platform data
i2c: mux: pca954x: remove support for unused platform data
dt-bindings: i2c: i2c-mtk: add support for MT8516
i2c: axxia: use auto cmd for last message
i2c: gpio: flag atomic capability if possible
i2c: algo: bit: add flag to whitelist atomic transfers
i2c: stu300: use xfer_atomic callback to bail out early
i2c: ocores: enable atomic xfers
i2c: ocores: refactor setup for polling
i2c: tegra-bpmp: convert to use new atomic callbacks
i2c: omap: Add the master_xfer_atomic hook
...
Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here last
Friday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKuwg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymRUgCfa8Ri7KrCaBR5NHQcLhbdrX90ToQAmgNw7vpo
fqt0XpNM0CSa9O/gOr79
=8HFh
-----END PGP SIGNATURE-----
Merge tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here
last Friday"
* tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits)
USB: serial: f81232: implement break control
USB: serial: f81232: add high baud rate support
USB: serial: f81232: clear overrun flag
USB: serial: f81232: fix interrupt worker not stop
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
...
We need this to make the usb-gadget branch merge cleaner. And for
testing to keep from hitting the same issues already fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use __maybe_unused for power management related functions
instead of #if CONFIG_PM_SLEEP to simply the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Hygon Dhyana CPU has the SMBus device with PCI device ID 0x790b,
which is the same as AMD CZ SMBus device. So add Hygon Dhyana support
to the i2c-piix4 driver by using the code path of AMD.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mainly some pca954x work, i.e. removal of unused platform data support
and added support for sysfs interface for manipulating/examining the
idle state. And then a mechanical cocci-style patch.
The I2C host driver for SynQuacer fails to populate the of_node and
ACPI companion fields of the struct i2c_adapter it instantiates,
resulting in enumeration of the subordinate I2C bus to fail.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are two problems with dev_err() here. One: It is not ratelimited.
Two: We don't see which driver tried to transfer something with a
suspended adapter. Switch to dev_WARN_ONCE to fix both issues. Drawback
is that we don't see if multiple drivers are trying to transfer while
suspended. They need to be discovered one after the other now. This is
better than a high CPU load because a really broken driver might try to
resend endlessly.
Link: https://bugs.archlinux.org/task/62391
Fixes: 2751541555 ("i2c: designware: Do not allow i2c_dw_xfer() calls while suspended")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reported-by: skidnik <skidnik@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: skidnik <skidnik@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adding device property "ccgx,firmware-build" for the CCGx
device, so the CCGx driver knows which firmware binary to
use for a specific vendor.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the iProc I2C driver to use the 'BIT' macro from all '1 << XXX'
bit operations to get rid of compiler warning and improve readability of
the code
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some recent commits to this driver were trying to make sure the TSS
interrupt is not generated on busy system due to 25ms timer expiring
between commands. It can still happen, however if STOP command is not
issued on time at the end of the transmission. If wait_for_completion in
axxia_i2c_xfer_msg() would not return after 25ms of getting an
interrupt, TSS will be generated and idev->err_msg will be set to
-ETIMEDOUT which will be returned from the axxia_i2c_xfer_msg(), even
though the transfer did actually succeed (STOP is automatically issued
when TSS triggers).
Fortunately, apart from already used manual and sequence commands, the
controller also has so called auto command. It works just like manual
mode but it but an automatic STOP is issued when either transfer length
is met or NAK is received from slave device.
This patch changes the axxia_i2c_xfer_msg() function so that auto
command is used for last message in transaction letting hardware manage
issuing STOP. TSS is disabled just after command transferring last
message finishes. Auto command, just like sequence, ends with SS
interrupt instead of SNS so handling of both had to be unified.
The axxia_i2c_stop() is no longer needed as the transfer can only end
with following conditions:
- fully successful - then last message was send by AUTO command and STOP
was issued automatically
- NAK received - STOP is issued automatically by controller
- arbitration lost - STOP should not be issued as we don't control the
bus
- IP interrupt received - this is sent when transfer length is set to 0
for auto/sequence command. The check for that is done before START is
send so no STOP is required
- TSS received between commands - STOP is issued by the controller
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If switching GPIOs does not sleep, then we can support atomic transfers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the new callback to reject atomic transfers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver already has the routine in place, tie it to the new callback.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
By properly setting up the algorithm at probe time, we can skip the
check at every transfer. This allows us to get rid of the flags
completely.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver did handle this internally, convert it to use the new
callbacks.
Reviewed-by: Timo Alho <talho@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add the master_xfer_atomic hook to enable i2c transactions in irq
disabled contexts like the poweroff case.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
[wsa: simplified code a little: 'timeout = !ret']
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No further occurences in the driver.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c compatible for MT8183. Compare to MT2712 i2c controller,
MT8183 has different register offsets. Ltiming_reg is added to
adjust low width of SCL. Arb clock and dma_sync are needed.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When i2c and apdma use different source clocks, we should enable
synchronization between them.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When two i2c controllers are internally connected to the same
GPIO pins, the arb clock is needed to ensure that the waveforms
do not interfere with each other. And we also need to enable
the interrupt to find arb lost, old i2c controllers also have
the bit.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
New i2c registers would have different offsets, so we use different
offsets array to distinguish different i2c registers version.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure to free the i2c adapter on the error exit path.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: e1ab9a468e ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 54fb4a05af ("i2c: Check for ACPI resource conflicts") included
<linux/acpi.h> so we could use acpi_check_region(). Commit fd46a0064a
("i2c: convert i2c-isch to platform_device") removed the use of
acpi_check_region() but not the include.
Remove the now-unnecessary include of <linux/acpi.h>. No functional change
intended.
Fixes: fd46a0064a ("i2c: convert i2c-isch to platform_device")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"res" can't be NULL because it's a pointer to somewhere in the middle of
the "adev" struct. Also probe() succeeded so there is no need to check
here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add NIC I2C support to the iProc I2C driver. Access to the NIC I2C base
registers requires going through the IDM wrapper to map into the NIC's
address space
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the following wrapper for read/write access of iProc i2c registers:
u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
u32 offset)
void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c, u32 offset,
u32 val)
This preps the driver for support of indirect register access required
by certain SoCs with this iProc I2C block integrated
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add polling support to the iProc I2C driver. Polling mode is
activated when the driver fails to obtain an interrupt ID from device
tree
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for more master error status including FIFO underrun and RX
FIFO full
Signed-off-by: Michael Cheng <ccheng@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add slave mode support to the iProc I2C driver.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Michael Cheng <ccheng@broadcom.com>
Signed-off-by: Shreesha Rajashekar <shreesha.rajashekar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support to allow I2C master read transfer up to 255 bytes.
Signed-off-by: Shreesha Rajashekar <shreesha@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
MP2 controllers have two separate busses, so may accommodate up to two I2C
adapters. Those adapters are listed in the ACPI namespace with the
"AMDI0011" HID, and probed by a platform driver.
Communication with the MP2 takes place through MMIO registers, or through
DMA for more than 32 bytes transfers.
This is major rework of the patch submitted by Nehal-bakulchandra Shah from
AMD (https://patchwork.kernel.org/patch/10597369/).
Most of the event handling of v3 was rewritten to make it work with more
than one bus (e.g on Ryzen-based Lenovo Yoga 530), and this version
contains many other improvements.
Signed-off-by: Elie Morisse <syniurge@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Slave mode driver is based on the concept of i2c-designware driver.
Signed-off-by: Juergen Fitschen <me@jue.yt>
[ludovic.desroches@microchip.com: rework Kconfig and replace IS_ENABLED
by defined]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The single file i2c-at91.c has been split into core code (i2c-at91-core.c)
and master mode specific code (i2c-at91-master.c). This should enhance
maintainability and reduce ifdeffery for slave mode related code.
The code itself hasn't been touched. Shared functions only had to be made
non-static. Furthermore, includes have been cleaned up.
Signed-off-by: Juergen Fitschen <me@jue.yt>
[ludovic.desroches@microchip.com: fix checkpatch errors and use SPDX]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In order to implement slave mode support for the at91 hardware we have to
segregate all master mode specific function parts from the general parts.
The upcoming slave mode patch will call its sepcific probe resp. init
function instead of the master mode functions after the shared general
code has been executed.
This concept has been influenced by the i2c-designware driver.
Signed-off-by: Juergen Fitschen <me@jue.yt>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When sending with DMA, the driver transfers the first byte with PIO (as
documented). However, it started DMA right after the first byte was
written. This worked, but was not according to the datasheet which
suggests to wait until data register was empty again. Implement this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We will need to know if enabling DMA was successful in a later patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a macro for the hardcoded value and apply a build check. If it is
not met, the driver logic will not work anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This avoids useless loops inside the I2C timing algorithm.
Actually, we support only one possible solution per prescaler value.
So after finding a solution with a prescaler, the algorithm can
switch directly to the next prescaler value.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Synopsys I2C Controller has an interface clock, but most SoCs hide
this away. However, on some SoCs you need to explicitly enable the
interface clock in order to access the registers. Therefore, add
support for an optional interface clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add PCI ID for Intel Comet Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Before this commit the i2c-designware-platdrv assumes that if the pdev
has an apci-companion it should use a dynamic adapter-nr and it sets
adapter->nr to -1, otherwise it will use pdev->id as adapter->nr.
There are 3 ways how platform_device-s to which i2c-designware-platdrv
will bind can be instantiated:
1) Through of / devicetree
2) Through ACPI enumeration
3) Explicitly instantiated through platform_device_create + add
1) In case of devicetree-instantiation the drivers/of code always sets
pdev->id to PLATFORM_DEVID_NONE, which is -1 so in this case both paths
to set adapter->nr end up doing the same thing.
2) In case of ACPI instantiation the device will always have an
ACPI-companion, so we are already using dynamic adapter-nrs.
3) There are 2 places manually instantiating a designware_i2c platform_dev:
drivers/mfd/intel_quark_i2c_gpio.c
drivers/mfd/intel-lpss.c
In the intel_quark_i2c_gpio.c case pdev->id is always 0, so switching to
dynamic adapter-nrs here could lead to the bus-number no longer being
stable, but the quark X1000 only has 1 i2c-controller, which will also
be assigned bus-number 0 when using dynamic adapter-nrs.
In the intel-lpss.c case intel_lpss_probe() is called from either
intel-lpss-acpi.c in which case there always is an ACPI-companion, or
from intel-lpss-pci.c. In most cases devices handled by intel-lpss-pci.c
also have an ACPI-companion, so we use a dynamic adapter-nr. But in some
cases the ACPI-companion is missing and we would use pdev->id (allocated
from intel_lpss_devid_ida). Devices which use the intel-lpss-pci.c code
typically have many i2c busses, so using pdev->id in this case may lead
to a bus-number conflict, triggering a WARN(id < 0, "couldn't get idr")
in i2c-core-base.c causing an oops an the adapter registration to fail.
So in this case using non dynamic adapter-nrs is actually undesirable.
One machine on which this oops was triggering is the Apollo Lake based
Acer TravelMate Spin B118.
TL;DR: Switching to always using dynamic adapter-numbers does not make
any difference in most cases and in the one case where it does make a
difference the behavior change is desirable because the old behavior
caused an oops.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1687065
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c-designware-platdrv assumes that if the pdev has an apci-companion
it should use a dynamic adapter-nr and otherwise it will use pdev->id
as adapter-nr.
Before this commit the setting of the adapter.nr was somewhat convoluted,
in the acpi_companion case it was set from dw_i2c_acpi_configure, in the
non acpi_companion case it was set from dw_i2c_set_fifo_size based on
tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was
not executed.
This cleans this up, directly setting the adapter-nr from
dw_i2c_plat_probe for both cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
To make sure people can understand the lockless design of this driver
without the need to dive into git history, add a comment giving an
overview of the situation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes the problem that an interrupt may set up a new I2C
message and the DMA callback overwrites this setup.
By disabling the DMA Enable Register(ICDMAER), rcar_i2c_dma_unmap()
enables interrupts for register settings (such as Master Control
Register(ICMCR)) and advances the I2C transfer sequence.
If an interrupt occurs immediately after ICDMAER is disabled, the
callback handler later continues and overwrites the previous settings
from the interrupt. So, disable ICDMAER at the end of the callback to
ensure other interrupts are masked until then.
Note that this driver needs to work lock-free because there are IP cores
with a HW race condition which prevent us from using a spinlock in the
interrupt handler.
Reproduction test:
1. Add a delay after disabling ICDMAER. (It is expected to generate an
interrupt of rcar_i2c_irq())
void rcar_i2c_dma_unmap(struct rcar_i2c_priv *priv)
{
...
rcar_i2c_write(priv, ICDMAER, 0);
usleep_range(500, 800)
...
priv->dma_direction = DMA_NONE;
}
2. Execute DMA transfers
$ i2ctransfer -y 4 w9@0x6a 1 1+ r16
3. A log message of BUG_ON() will be displayed.
Fixes: 73e8b05283 ("i2c: rcar: add DMA support")
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: updated test case to be more reliable, added note to comment]
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When compiling with -Wformat, clang warns:
drivers/i2c/busses/i2c-sis630.c:482:4: warning: format specifies type
'unsigned short' but the argument has type 'int' [-Wformat]
smbus_base + SMB_STS,
^~~~~~~~~~~~~~~~~~~~
drivers/i2c/busses/i2c-sis630.c:483:4: warning: format specifies type
'unsigned short' but the argument has type 'int' [-Wformat]
smbus_base + SMB_STS + SIS630_SMB_IOREGION - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/i2c/busses/i2c-sis630.c:531:37: warning: format specifies type
'unsigned short' but the argument has type 'int' [-Wformat]
"SMBus SIS630 adapter at %04hx", smbus_base + SMB_STS);
~~~~~ ^~~~~~~~~~~~~~~~~~~~
This patch fixes the format strings to use the format type for int.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Louis Taylor <louis@kragniz.eu>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA with zero-length transfers doesn't make sense and this HW doesn't
support them at all, so increase the threshold.
Fixes: fc66b39fe3 ("i2c: mediatek: Use DMA safe buffers for i2c transactions")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAlyCpL0UHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vzoHw//ZyFbwekF0mV3RZwcV35LkScIOw0d
O1DgjJo8UbuV51+/foQeUZ8IzjHlybQhoFdJupPuw+LyaDUkwqjAmdtY8J/FjWSm
AJeVzu6gMF0Z9kwwGO4NyqX2EWluTD0xNLgf8g+fe3p1MtEuH6VCrqe+hk3wma0K
CrSIKWY/sO408SpAaWiLTEZmVT+hXiP9hJw1qTrbqKLtyWa4oCjErdoyUDsA01+5
gPndKC/3pu6q6q9Dd94582HuQaE2dKHWQXx6Fzd/tdCyYffpbOUAUNP3aRXaTKrS
MwKxOF3y7yUnz5RbxRgopwNVf5WyXhCnnPZRLaSxqnTSZCY6FCUi3l6RpVyWu2Ha
iztBbkTP/x6WV3VWg810qgQKQ9wl8oALMkoOfR6lWCR7MTuJnMXJtbrz0jWpEC2O
ZPwK9fAxFj2/3e13hx88O7Ek8kfajTPM8T15K79pvpljfqa0BD9SrhPyQ5ssmxj4
idz4yIFCATULKszPXA1QbfC1/xCDveQOEPSerL3eACXsLN17vfpOwOT9vWJm6bpr
6u5ggM2dEA07eI1ANnY6twn5g0kSYU9qISNQO98tA86IvaCnME0Z+k+SCwUNIM9U
ep9k0NdAGDNsYOfdVEEY0fYGT9k+9f9w8AfZLNvh0N3s7mGQQ35jf0Z75jj/jsor
cbMcPAN2jOCyFVs=
=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
Pull i2c updates from Wolfram Sang:
- the I2C core gained helpers to assist drivers in handling their
suspended state, and drivers were converted to use it
- two new fault-injectors for stress-testing
- bigger refactoring and feature improvements for the ocores,
sh_mobile, and tegra drivers
- platform_data removal for the at24 EEPROM driver
- ... and various improvements and bugfixes all over the subsystem
* 'i2c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (69 commits)
i2c: Allow recovery of the initial IRQ by an I2C client device.
i2c: ocores: turn incomplete kdoc into a comment
i2c: designware: Do not allow i2c_dw_xfer() calls while suspended
i2c: tegra: Only display error messages if DMA setup fails
i2c: gpio: fault-injector: add 'inject_panic' injector
i2c: gpio: fault-injector: add 'lose_arbitration' injector
i2c: tegra: remove multi-master support
i2c: tegra: remove master fifo support on tegra186
i2c: tegra: change phrasing, "fallbacking" to "falling back"
i2c: expand minor range when registering chrdev region
i2c: aspeed: Add multi-master use case support
i2c: core-smbus: don't trace smbus_reply data on errors
i2c: ocores: Add support for bus clock via platform data
i2c: ocores: Add support for IO mapper registers.
i2c: ocores: checkpatch fixes
i2c: ocores: add SPDX tag
i2c: ocores: add polling interface
i2c: ocores: do not handle IRQ if IF is not set
i2c: ocores: stop transfer on timeout
i2c: tegra: add i2c interface timing support
...
gcc complains, rightfully so, I think:
drivers/i2c/busses/i2c-ocores.c:32: warning: Cannot understand * @process_lock: protect I2C transfer process.
on line 32 - I thought it was a doc line
Make it a simple comment.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On most Intel Bay- and Cherry-Trail systems the PMIC is connected over I2C
and the PMIC is accessed through various means by the _PS0 and _PS3 ACPI
methods (power on / off methods) of various devices.
This leads to suspend/resume ordering problems where a device may be
resumed and get its _PS0 method executed before the I2C controller is
resumed. On Cherry Trail this leads to errors like these:
i2c_designware 808622C1:06: controller timed out
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
video LNXVIDEO:00: Failed to change power state to D0
But on Bay Trail this caused I2C reads to seem to succeed, but they end
up returning wrong data, which ends up getting written back by the typical
read-modify-write cycle done to turn on various power-resources.
Debugging the problems caused by this silent data corruption is quite
nasty. This commit adds a check which disallows i2c_dw_xfer() calls to
happen until the controller's resume method has completed.
Which turns the silent data corruption into getting these errors in
dmesg instead:
i2c_designware 80860F41:04: Error i2c_dw_xfer call while suspended
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.PCI0.GFX0._PS0, AE_ERROR
Which is much better.
Note the above errors are an example of issues which this patch will
help to debug, the actual fix requires fixing the suspend order and
this has been fixed by a different commit.
Note the setting / clearing of the suspended flag in the suspend / resume
methods is NOT protected by i2c_lock_bus(). This is intentional as these
methods get called from i2c_dw_xfer() (through pm_runtime_get/put) a nd
i2c_dw_xfer() is called with the i2c_bus_lock held, so otherwise we would
deadlock. This means that there is a theoretical race between a non runtime
suspend and the suspended check in i2c_dw_xfer(), this is not a problem
since normally we should not hit the race and this check is primarily a
debugging tool so hitting the check if there are suspend/resume ordering
problems does not need to be 100% reliable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 86c92b9965 ("i2c: tegra: Add DMA support") added DMA support
to the Tegra I2C driver for Tegra devices that support the APB DMA
controller. One side-effect of this change is that even for Tegra
devices that do not have an APB DMA controller and hence, cannot
support DMA tranfers for I2C transactions, the following error messages
are still displayed ...
ERR KERN tegra-i2c 31c0000.i2c: cannot use DMA: -19
ERR KERN tegra-i2c 31c0000.i2c: falling back to PIO
There is no point displaying the above messages for devices that do not
have an APB DMA controller and so fix this by returning from the
tegra_i2c_init_dma() function if 'has_apb_dma' is not true.
Furthermore, if CONFIG_TEGRA20_APB_DMA is not set, then rather than
printing an error message, print an debug message as for whatever reason
this could be intentional.
Fixes: 86c92b9965 ("i2c: tegra: Add DMA support")
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a fault injector simulating a Kernel panic happening after starting
a transfer. Read the docs for its usage.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a fault injector simulating 'arbitration lost' from multi-master
setups. Read the docs for its usage.
A helper function for future fault injectors using SCL interrupts is
created to achieve this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Multi-master support is defeatured on Tegra210 and Tegra186 due to
known bugs.
This patch removes multi-master support for Tegra210 and Tegra186
I2C HW feature.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra186 does not have master FIFO control register and instead
uses FIFO control register like prior Tegra chipset.
This patch fixes this and prevents crashing during boot when
accessing FIFO control registers.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The phrasing in two dev_err messages is using fallbacking which
os less understandable than "falling back", so fix this up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In multi-master environment, this driver's master cannot know
exactly when a peer master sends data to this driver's slave so
cases can be happened that this master tries sending data through
the master_xfer function but slave data from a peer master is still
being processed or slave xfer is started by a peer immediately
after it queues a master command. To support multi-master use cases
properly, this H/W provides arbitration in physical level and it
provides priority based command handling too to avoid conflicts in
multi-master environment, means that if a master and a slave events
happen at the same time, H/W will handle a higher priority event
first and a pending event will be handled when bus comes back to
the idle state.
To support this H/W feature properly, this patch adds the 'pending'
state of master and its handling code so that the pending master
xfer can be continued after slave operation properly.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver's interrupt handler checks whether a message is currently
being handled with the curr_msg pointer. When it is NULL, the interrupt
is considered to be unexpected. Similarly, the i2c_start_transfer
routine checks for the remaining number of messages to handle in
num_msgs.
However, these values are never cleared and always keep the message and
number relevant to the latest transfer (which might be done already and
the underlying message memory might have been freed).
When an unexpected interrupt hits with the DONE bit set, the isr will
then try to access the flags field of the curr_msg structure, leading
to a fatal page fault.
The msg_buf and msg_buf_remaining fields are also never cleared at the
end of the transfer, which can lead to similar pitfalls.
Fix these issues by introducing a cleanup function and always calling
it after a transfer is finished.
Fixes: e247454103 ("i2c: bcm2835: Fix hang for writing messages larger than 16 bytes")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case the hold bit is not needed we are carrying the old values.
Fix the same by resetting the bit when not needed.
Fixes the sporadic i2c bus lockups on National Instruments
Zynq-based devices.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Reported-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add the I2C bus clock speed to the platform data structure.
If not set, default to 100KHz as before.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some implementations of the OCORES i2c bus master use IO mapped
registers. Add support for getting the IO registers from the platform
data, and register accessor functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Miscellaneous style fixes from checkpatch
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It adds the SPDX tag and it removes the old text about the GPLv2.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver assumes that an interrupt line is always available for
the I2C master. This is not always the case and this patch adds support
for a polling version.
Report from Andrew Lunn:
I did some timing tests for this. On my box, we request a udelay of
80uS. The kernel actually delays for about 79uS. We then spin in
ocores_wait() for an additional 10-11uS, which is 3 to 4 iterations.
There are actually 9 bits on the wire, not 8, since there is an
ACK/NACK bit after the actual data transfer. So i changed the delay to
(9 * 1000) / i2c->bus_clock_khz. That resulted in ocores_wait() mostly
not looping at all. But for reading an 4K AT24 EEPROM, it increased
the read time by 10ms, from 424ms to 434ms. So we should probably keep
with 8.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the Interrupt Flag (IF) is not set, we should not handle the IRQ:
- the line can be shared with other devices
- it can be a spurious interrupt
To avoid reading twice the status register, the ocores_process() function
expects it to be read by the caller.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Detecting a timeout is ok, but we also need to assert a STOP command on
the bus in order to prevent it from generating interrupts when there are
no on going transfers.
Example: very long transmission.
1. ocores_xfer: START a transfer
2. ocores_isr : handle byte by byte the transfer
3. ocores_xfer: goes in timeout [[bugfix here]]
4. ocores_xfer: return to I2C subsystem and to the I2C driver
5. I2C driver : it may clean up the i2c_msg memory
6. ocores_isr : receives another interrupt (pending bytes to be
transferred) but the i2c_msg memory is invalid now
So, since the transfer was too long, we have to detect the timeout and
STOP the transfer.
Another point is that we have a critical region here. When handling the
timeout condition we may have a running IRQ handler. For this reason I
introduce a spinlock.
In order to make easier to understan locking I have:
- added a new function to handle timeout
- modified the current ocores_process() function in order to be protected
by the new spinlock
Like this it is obvious at first sight that this locking serializes
the execution of ocores_process() and ocores_process_timeout()
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds I2C interface timing registers support for
proper bus rate configuration along with meeting the I2C spec
setup and hold times based on the tuning performed on Tegra210,
Tegra186 and Tegra194 platforms.
I2C_INTERFACE_TIMING_0 register contains TLOW and THIGH field
and Tegra I2C controller design uses them as a part of internal
clock divisor.
I2C_INTERFACE_TIMING_1 register contains the setup and hold times
for start and stop conditions.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra194 allows max of 64K bytes and Tegra186 and prior allows
max of 4K bytes of transfer per packet.
one sec timeout is not enough for transfers more than 10K bytes
at STD bus rate.
This patch updates I2C transfer timeout based on the transfer size
and I2C bus rate to allow enough time during max transfer size at
lower bus speed.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds DMA support for Tegra I2C.
Tegra I2C TX and RX FIFO depth is 8 words. PIO mode is used for
transfer size of the max FIFO depth and DMA mode is used for
transfer size higher than max FIFO depth to save CPU overhead.
PIO mode needs full intervention of CPU to fill or empty FIFO's
and also need to service multiple data requests interrupt for the
same transaction. This adds delay between data bytes of the same
transfer when CPU is fully loaded and some slave devices has
internal timeout for no bus activity and stops transaction to
avoid bus hang. DMA mode is helpful in such cases.
DMA mode is also helpful for Large transfers during downloading or
uploading FW over I2C to some external devices.
Tegra210 and prior Tegra chips use APBDMA driver which is replaced
with GPCDMA on Tegra186 and Tegra194.
This patch uses has_apb_dma flag in hw_feature to differentiate
DMA driver change between Tegra chipset.
APBDMA driver is registered from module-init level and this patch
also has a change to register I2C driver at module-init level
rather than subsys-init to avoid deferring I2C probe till APBDMA
driver is registered.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra194 supports maximum 64K bytes per packet including 12 bytes of
packet header irrespective of PIO or DMA mode transfer.
This patch updates Tegra194 max write length to account for packet
header size for transfers.
Cc: stable@vger.kernel.org # 4.20+
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra186 and prior supports maximum 4K bytes per packet transfer
including 12 bytes of packet header.
This patch fixes max write length limit to account packet header
size for transfers.
Cc: stable@vger.kernel.org # 4.4+
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Bus clear feature of Tegra I2C controller helps to recover from
bus hang when I2C master loses the bus arbitration due to the
slave device holding SDA LOW continuously for some unknown reasons.
Per I2C specification, the device that held the bus LOW should
release it within 9 clock pulses.
During bus clear operation, Tegra I2C controller sends 9 clock
pulses and terminates the transaction with STOP condition.
Upon successful bus clear operation, bus goes to idle state and
driver retries the transaction.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch sorts all the include headers alphabetically for the
I2C Tegra driver.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The latest documentation made it clear that we need to initialize the
TCYC value independently of DMA. The old code used TCYC06 (wrongly) for
non-DMA transfers. The new code sets TCYC up independently from DMA.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I think it is clear enough if we have the explanation once and make it
clear it is applicable for both SCL and SDA. Reword it a little with
the help of Simon's native language skills :)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We measured the clock on a Lager and an Ebisu board. The new formula
gives better results for both. So after Gen3, switch to this formula for
all Gen2 SoCs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We could finally measure the clock on an Ebisu board. The new formula
gives way better results, i.e. 100kHz instead of 106kHz and 400kHz
instead of 387kHz. Switch to these formulas for all Gen3 SoCs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Makes it easier to add new ones.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This augments the CBUS GPIO I2C driver to use GPIO
descriptors for clock, sel and data. We drop the platform
data that was only used for carrying GPIO numbers and
use machine descriptor tables instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update copyright years and remove a comment which grew incorrect and
useless over time.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no value in chronological sorting. Make it easier to follow for
humans.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Completion_done() is useless when we don't use its return value,
so we remove it.
Signed-off-by: qii wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Different speeds have been defined by macros,
so we use macros definitions.
Signed-off-by: qii wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Less risk for duplications when adding new ones.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds device tree probing support for the IOP3xx
I2C master.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We currently get the following error with pixcir_ts driver during a
suspend resume cycle:
omap_i2c 4802a000.i2c: controller timed out
pixcir_ts 1-005c: pixcir_int_enable: can't read reg 0x34 : -110
pixcir_ts 1-005c: Failed to disable interrupt generation: -110
pixcir_ts 1-005c: Failed to stop
dpm_run_callback(): pixcir_i2c_ts_resume+0x0/0x98
[pixcir_i2c_ts] returns -110
PM: Device 1-005c failed to resume: error -110
And at least am437x based devices with pixcir_ts will fail to resume
to a touchscreen that is configured as the wakeup-source in device
tree for these devices.
This is because pixcir_ts tries to reconfigure it's registers for
noirq suspend which fails. This also leaves i2c-omap in enabled state
for suspend.
Let's fix the pixcir_ts issue and make sure i2c-omap is suspended by
adding SET_NOIRQ_SYSTEM_SLEEP_PM_OPS.
Let's also get rid of some ifdefs while at it and replace them with
__maybe_unused as SET_RUNTIME_PM_OPS and SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
already deal with the various PM Kconfig options.
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This commit removes hard-coded bus timeout value setting so that
it can be set by i2c-core-base.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update copyright years and add Renesas to it. Add/update comments to
make driver easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the do_while loop which was just there to have an easy exit with
"break;" and replace it with if-else-blocks which should make the state
machine clearer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation to remove the do-while-loop.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All state machines deal with pd->pos values. This helper function is an
exception and makes it only more confusing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Akshu Agrawal