Use the appropriate SPDX license identifiers and drop the license text.
This patch is only cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: f9358e12a0 ("net: mvpp2: split ingress traffic into multiple flows")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows setting the RSS hash generation parameters from
ethtool. When setting parameters for a given flow type from ethtool
(e.g. tcp4), all the corresponding flows in the flow table are updated,
according to the supported hash parameters.
For example, when configuring TCP over IPv4 hash parameters to be
src/dst IP + src/dst port ("ethtool -N eth0 rx-flow-hash tcp4 sdfn"),
we only set the "src/dst port" hash parameters on the non-fragmented TCP
over IPv4 flows.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the classification action that can be performed is to compute a
hash of the packet header based on some header fields, and lookup a RSS
table based on this hash to determine the final RxQ.
This is done by adding one lookup entry per flow per port, so that we
can configure the hash generation parameters for each flow and each
port.
There are 2 possible engines that can be used for RSS hash generation :
- C3HA, that generates a hash based on up to 4 header-extracted fields
- C3HB, that does the same as c3HA, but also includes L4 info in the hash
There are a lot of fields that can be extracted from the header. For now,
we only use the ones that we can configure using ethtool :
- DST MAC address
- L3 info
- Source IP
- Destination IP
- Source port
- Destination port
The C3HB engine is selected when we use L4 fields (src/dst port).
Header parser Dec table
Ingress pkt +-------------+ flow id +----------------------------+
------------->| TCAM + SRAM |-------->|TCP IPv4 w/ VLAN, not frag |
+-------------+ |TCP IPv4 w/o VLAN, not frag |
|TCP IPv4 w/ VLAN, frag |--+
|etc. | |
+----------------------------+ |
|
Flow table |
+---------+ +------------+ +--------------------------+ |
| RSS tbl |<--| Classifier |<--------| flow 0: C2 lookup | |
+---------+ +------------+ | C3 lookup port 0 | |
| | | C3 lookup port 1 | |
+-----------+ +-------------+ | ... | |
| C2 engine | | C3H engines | | flow 1: C2 lookup |<--+
+-----------+ +-------------+ | C3 lookup port 0 |
| ... |
| ... |
| flow 51 : C2 lookup |
| ... |
+--------------------------+
The C2 engine also gains the role of enabling and disabling the RSS
table lookup for this packet.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 classifier allows to perform classification operations on each
ingress packet, based on the flow the packet is assigned to.
The current code uses only 1 flow per port, and the only classification
action consists of assigning the rx queue to the packet, depending on the
port.
In preparation for adding RSS support, we have to split all incoming
traffic into different flows. Since RSS assigns a rx queue depending on
the hash of some header fields, we have to make sure that the hash is
generated in a consistent way for all packets in the same flow.
What we call a "flow" is actually a set of attributes attached to a
packet that depends on various L2/L3/L4 info.
This patch introduces 52 flows, wich are a combination of various L2, L3
and L4 attributes :
- Whether or not the packet has a VLAN tag
- Whether the packet is IPv4, IPv6 or something else
- Whether the packet is TCP, UDP or something else
- Whether or not the packet is fragmented at L3 level.
The flow is associated to a packet by the Header Parser. Each flow
corresponds to an entry in the decoding table. This entry then points to
the sequence of classification lookups to be performed by the
classifier, represented in the flow table.
For now, the only lookup we perform is a C2 lookup to set the default
rx queue.
Header parser Dec table
Ingress pkt +-------------+ flow id +----------------------------+
------------->| TCAM + SRAM |-------->|TCP IPv4 w/ VLAN, not frag |
+-------------+ |TCP IPv4 w/o VLAN, not frag |
|TCP IPv4 w/ VLAN, frag |--+
|etc. | |
+----------------------------+ |
|
Flow table |
+------------+ +---------------------+ |
To RxQ <---| Classifier |<-------| flow 0: C2 lookup |<--------+
+------------+ | flow 1: C2 lookup |
| | ... |
+------------+ | flow 51 : C2 lookup |
| C2 engine | +---------------------+
+------------+
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 Controller has a classifier, that can perform multiple lookup
operations for each packet, using different engines.
One of these engines is the C2 engine, which performs TCAM based lookups
on data extracted from the packet header. When a packet matches an
entry, the engine sets various attributes, used to perform
classification operations.
One of these attributes is the rx queue in which the packet should be sent.
The current code uses the lookup_id table (also called decoding table)
to assign the rx queue. However, this only works if we use one entry per
port in the decoding table, which won't be the case once we add RSS
lookups.
This patch uses the C2 engine to assign the rx queue to each packet.
The C2 engine is used through the flow table, which dictates what
classification operations are done for a given flow.
Right now, we have one flow per port, which contains every ingress
packet for this port.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp22_init_rss function configures the RSS parameters for each port, so
rename it accordingly. Since this function relies on classifier
configuration, move its call right after the classifier config.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling the RSS table, we have to make sure that the rx queue is
attached to an online CPU.
This patch is not a full support for cpu_hotplug, but rather a way to
make sure that we don't break network on system booted with the maxcpus
parameter.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an extra indirection when setting the indirection table
into the RSS hardware table to improve the packets distribution across
CPUs. For example, if 2 queues are used on a multi-core system this new
indirection will choose two queues on two different CPUs instead of the
two first queues which are on the same first CPU.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the RSS indirection table support, allowing to use the
ethtool -x and -X options to dump and set this table.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
[Maxime: Small warning fixes, use one table per port]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2 Controller has 8 RSS Tables, of 32 entries each. A lookup in the
RXQ2RSS_TABLE is performed for each incoming packet, and the RSS Table
to be used is chosen according to the default rx queue that would be
used for the packet.
This default rx queue is set in the Lookup_id Table (also called
Decoding Table), and is equal to the port->first_rxq.
Since the Classifier itself isn't active at any time for the moment,
this doesn't have a direct effect, the default rx queue at the moment is
the one where all packets end-up into.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no RSS_TABLE register in PPv2 Controller. The register 0x1510
which was specified is actually named "RSS_HASH_SEL", but isn't used by
this driver at all.
Based on how this register was used, it should have been the
RXQ2RSS_TABLE register, which allows to select the RSS table that will
be used for the incoming packet.
The RSS_TABLE_POINTER is actually a field of this RXQ2RSS_TABLE
register.
Since RSS tables are actually not used by the driver for now, this
commit does not fix a runtime bug.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch fixing a typo in one of the RSS comments.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the mvpp2 driver is growing, move this driver to a dedicated
directory and split it into several files.
Since this driver has a lot of register defines and structure
definitions, it can benefit from having all of this into a dedicated
header file, named mvpp2.h.
A good chunk of the mvpp2 code is dedicated to Header Parser handling, so
we introduce mvpp2_prs.h where all Header Parser definitions are located,
and mvpp2_prs.c containing the related code.
In the same way, mvpp2_cls.h and mvpp2_cls.c are created to contain
Classifier and RSS related code.
The former 'mvpp2.c' file is renamed 'mvpp2_main.c' so that we can keep
the driver binary named 'mvpp2'.
This commit is only about spliting the driver into multiple files and
doesn't introduce any new function, feature or fix besides removing
'static' keywords when needed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart