Pull x86 vdso updates from Ingo Molnar:
"Further simplifications and improvements to the VDSO code, by Andy
Lutomirski"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64/vsyscall: Fix warn_bad_vsyscall log output
x86/vdso: Set VM_MAYREAD for the vvar vma
x86, vdso: Get rid of the fake section mechanism
x86, vdso: Move the vvar area before the vdso text
Pull x86 UV TLB update from Ingo Molnar:
"UV TLB shootdown logic updates for version of the UV architecture"
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/uv: Update the UV3 TLB shootdown logic
Pull RAS updates from Ingo Molnar:
"The main changes in this cycle are:
- RAS tracing/events infrastructure, by Gong Chen.
- Various generalizations of the APEI code to make it available to
non-x86 architectures, by Tomasz Nowicki"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ras: Fix build warnings in <linux/aer.h>
acpi, apei, ghes: Factor out ioremap virtual memory for IRQ and NMI context.
acpi, apei, ghes: Make NMI error notification to be GHES architecture extension.
apei, mce: Factor out APEI architecture specific MCE calls.
RAS, extlog: Adjust init flow
trace, eMCA: Add a knob to adjust where to save event log
trace, RAS: Add eMCA trace event interface
RAS, debugfs: Add debugfs interface for RAS subsystem
CPER: Adjust code flow of some functions
x86, MCE: Robustify mcheck_init_device
trace, AER: Move trace into unified interface
trace, RAS: Add basic RAS trace event
x86, MCE: Kill CPU_POST_DEAD
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle are:
- Intel SOC driver updates, by Aubrey Li.
- TS5500 platform updates, by Vivien Didelot"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pmc_atom: Silence shift wrapping warnings in pmc_sleep_tmr_show()
x86/pmc_atom: Expose PMC device state and platform sleep state
x86/pmc_atom: Eisable a few S0ix wake up events for S0ix residency
x86/platform: New Intel Atom SOC power management controller driver
x86/platform/ts5500: Add support for TS-5400 boards
x86/platform/ts5500: Add a 'name' sysfs attribute
x86/platform/ts5500: Use the DEVICE_ATTR_RO() macro
Pull x86 mm changes from Ingo Molnar:
"The main change in this cycle is the rework of the TLB range flushing
code, to simplify, fix and consolidate the code. By Dave Hansen"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Set TLB flush tunable to sane value (33)
x86/mm: New tunable for single vs full TLB flush
x86/mm: Add tracepoints for TLB flushes
x86/mm: Unify remote INVLPG code
x86/mm: Fix missed global TLB flush stat
x86/mm: Rip out complicated, out-of-date, buggy TLB flushing
x86/mm: Clean up the TLB flushing code
x86/smep: Be more informative when signalling an SMEP fault
Pull EFI changes from Ingo Molnar:
"Main changes in this cycle are:
- arm64 efi stub fixes, preservation of FP/SIMD registers across
firmware calls, and conversion of the EFI stub code into a static
library - Ard Biesheuvel
- Xen EFI support - Daniel Kiper
- Support for autoloading the efivars driver - Lee, Chun-Yi
- Use the PE/COFF headers in the x86 EFI boot stub to request that
the stub be loaded with CONFIG_PHYSICAL_ALIGN alignment - Michael
Brown
- Consolidate all the x86 EFI quirks into one file - Saurabh Tangri
- Additional error logging in x86 EFI boot stub - Ulf Winkelvos
- Support loading initrd above 4G in EFI boot stub - Yinghai Lu
- EFI reboot patches for ACPI hardware reduced platforms"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
efi/arm64: Handle missing virtual mapping for UEFI System Table
arch/x86/xen: Silence compiler warnings
xen: Silence compiler warnings
x86/efi: Request desired alignment via the PE/COFF headers
x86/efi: Add better error logging to EFI boot stub
efi: Autoload efivars
efi: Update stale locking comment for struct efivars
arch/x86: Remove efi_set_rtc_mmss()
arch/x86: Replace plain strings with constants
xen: Put EFI machinery in place
xen: Define EFI related stuff
arch/x86: Remove redundant set_bit(EFI_MEMMAP) call
arch/x86: Remove redundant set_bit(EFI_SYSTEM_TABLES) call
efi: Introduce EFI_PARAVIRT flag
arch/x86: Do not access EFI memory map if it is not available
efi: Use early_mem*() instead of early_io*()
arch/ia64: Define early_memunmap()
x86/reboot: Add EFI reboot quirk for ACPI Hardware Reduced flag
efi/reboot: Allow powering off machines using EFI
efi/reboot: Add generic wrapper around EfiResetSystem()
...
Pull x86 cpufeature updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued cleanups of CPU bugs mis-marked as 'missing features', by
Borislav Petkov.
- Detect the xsaves/xrstors feature and releated cleanup, by Fenghua
Yu"
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpu: Kill cpu_has_mp
x86, amd: Cleanup init_amd
x86/cpufeature: Add bug flags to /proc/cpuinfo
x86, cpufeature: Convert more "features" to bugs
x86/xsaves: Detect xsaves/xrstors feature
x86/cpufeature.h: Reformat x86 feature macros
Pull x86 build/cleanup/debug updates from Ingo Molnar:
"Robustify the build process with a quirk to avoid GCC reordering
related bugs.
Two code cleanups.
Simplify entry_64.S CFI annotations, by Jan Beulich"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, build: Change code16gcc.h from a C header to an assembly header
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Simplify __HAVE_ARCH_CMPXCHG tests
x86/tsc: Get rid of custom DIV_ROUND() macro
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/debug: Drop several unnecessary CFI annotations
The assumption was that update_mmu_cache() (and the equivalent for PMDs) would
only be called when the PTE being installed will be accessible by the user.
This is not true for code paths originating from remove_migration_pte().
There are dire consequences for placing a non-valid PTE into the TSB. The TLB
miss frramework assumes thatwhen a TSB entry matches we can just load it into
the TLB and return from the TLB miss trap.
So if a non-valid PTE is in there, we will deadlock taking the TLB miss over
and over, never satisfying the miss.
Just exit early from update_mmu_cache() and friends in this situation.
Based upon a report and patch from Christopher Alexander Tobias Schulze.
Signed-off-by: David S. Miller <davem@davemloft.net>
Building a 32-bit kernel with CONFIG_X86_USE_3DNOW and CONFIG_EFI_STUB
leads to the following build error,
drivers/firmware/efi/libstub/lib.a(efi-stub-helper.o): In function `efi_relocate_kernel':
efi-stub-helper.c:(.text+0xda5): undefined reference to `_mmx_memcpy'
This is due to the fact that the EFI boot stub pulls in the 3DNow
optimized versions of the memcpy() prototype from
arch/x86/include/asm/string_32.h, even though the _mmx_memcpy()
implementation isn't available in the EFI stub.
For now, predicate CONFIG_EFI_STUB on !CONFIG_X86_USE_3DNOW. This is
most definitely a temporary fix. A complete solution will involve
selectively including kernel headers/symbols into the early-boot
execution environment of the EFI boot stub, i.e. something analogous to
the way that the _SETUP symbol is used.
Previous attempts have been made to fix this kind of problem, though
none seem to have ever been merged,
http://lkml.kernel.org/r/20120329104822.GA17233@x1.osrc.amd.com
Clearly, this problem has been around for a long time.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1407193939-27813-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull perf changes from Ingo Molnar:
"Kernel side changes:
- Consolidate the PMU interrupt-disabled code amongst architectures
(Vince Weaver)
- misc fixes
Tooling changes (new features, user visible changes):
- Add support for pagefault tracing in 'trace', please see multiple
examples in the changeset messages (Stanislav Fomichev).
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add header for columns in 'top' and 'report' TUI browsers (Jiri
Olsa)
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add IO mode into timechart command (Stanislav Fomichev)
- Fallback to syscalls:* when raw_syscalls:* is not available in the
perl and python perf scripts. (Daniel Bristot de Oliveira)
- Add --repeat global option to 'perf bench' to be used in benchmarks
such as the existing 'futex' one, that was modified to use it
instead of a local option. (Davidlohr Bueso)
- Fix fd -> pathname resolution in 'trace', be it using /proc or a
vfs_getname probe point. (Arnaldo Carvalho de Melo)
- Add suggestion of how to set perf_event_paranoid sysctl, to help
non-root users trying tools like 'trace' to get a working
environment. (Arnaldo Carvalho de Melo)
- Updates from trace-cmd for traceevent plugin_kvm plus args cleanup
(Steven Rostedt, Jan Kiszka)
- Support S/390 in 'perf kvm stat' (Alexander Yarygin)
Tooling infrastructure changes:
- Allow reserving a row for header purposes in the hists browser
(Arnaldo Carvalho de Melo)
- Various fixes and prep work related to supporting Intel PT (Adrian
Hunter)
- Introduce multiple debug variables control (Jiri Olsa)
- Add callchain and additional sample information for python scripts
(Joseph Schuchart)
- More prep work to support Intel PT: (Adrian Hunter)
- Polishing 'script' BTS output
- 'inject' can specify --kallsym
- VDSO is per machine, not a global var
- Expose data addr lookup functions previously private to 'script'
- Large mmap fixes in events processing
- Include standard stringify macros in power pc code (Sukadev
Bhattiprolu)
Tooling cleanups:
- Convert open coded equivalents to asprintf() (Andy Shevchenko)
- Remove needless reassignments in 'trace' (Arnaldo Carvalho de Melo)
- Cache the is_exit syscall test in 'trace) (Arnaldo Carvalho de
Melo)
- No need to reimplement err() in 'perf bench sched-messaging', drop
barf(). (Davidlohr Bueso).
- Remove ev_name argument from perf_evsel__hists_browse, can be
obtained from the other parameters. (Jiri Olsa)
Tooling fixes:
- Fix memory leak in the 'sched-messaging' perf bench test.
(Davidlohr Bueso)
- The -o and -n 'perf bench mem' options are mutually exclusive, emit
error when both are specified. (Davidlohr Bueso)
- Fix scrollbar refresh row index in the ui browser, problem exposed
now that headers will be added and will be allowed to be switched
on/off. (Jiri Olsa)
- Handle the num array type in python properly (Sebastian Andrzej
Siewior)
- Fix wrong condition for allocation failure (Jiri Olsa)
- Adjust callchain based on DWARF debug info on powerpc (Sukadev
Bhattiprolu)
- Fix a risk for doing free on uninitialized pointer in traceevent
lib (Rickard Strandqvist)
- Update attr test with PERF_FLAG_FD_CLOEXEC flag (Jiri Olsa)
- Enable close-on-exec flag on perf file descriptor (Yann Droneaud)
- Fix build on gcc 4.4.7 (Arnaldo Carvalho de Melo)
- Event ordering fixes (Jiri Olsa)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (123 commits)
Revert "perf tools: Fix jump label always changing during tracing"
perf tools: Fix perf usage string leftover
perf: Check permission only for parent tracepoint event
perf record: Store PERF_RECORD_FINISHED_ROUND only for nonempty rounds
perf record: Always force PERF_RECORD_FINISHED_ROUND event
perf inject: Add --kallsyms parameter
perf tools: Expose 'addr' functions so they can be reused
perf session: Fix accounting of ordered samples queue
perf powerpc: Include util/util.h and remove stringify macros
perf tools: Fix build on gcc 4.4.7
perf tools: Add thread parameter to vdso__dso_findnew()
perf tools: Add dso__type()
perf tools: Separate the VDSO map name from the VDSO dso name
perf tools: Add vdso__new()
perf machine: Fix the lifetime of the VDSO temporary file
perf tools: Group VDSO global variables into a structure
perf session: Add ability to skip 4GiB or more
perf session: Add ability to 'skip' a non-piped event stream
perf tools: Pass machine to vdso__dso_findnew()
perf tools: Add dso__data_size()
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- big rtmutex and futex cleanup and robustification from Thomas
Gleixner
- mutex optimizations and refinements from Jason Low
- arch_mutex_cpu_relax() removal and related cleanups
- smaller lockdep tweaks"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
arch, locking: Ciao arch_mutex_cpu_relax()
locking/lockdep: Only ask for /proc/lock_stat output when available
locking/mutexes: Optimize mutex trylock slowpath
locking/mutexes: Try to acquire mutex only if it is unlocked
locking/mutexes: Delete the MUTEX_SHOW_NO_WAITER macro
locking/mutexes: Correct documentation on mutex optimistic spinning
rtmutex: Make the rtmutex tester depend on BROKEN
futex: Simplify futex_lock_pi_atomic() and make it more robust
futex: Split out the first waiter attachment from lookup_pi_state()
futex: Split out the waiter check from lookup_pi_state()
futex: Use futex_top_waiter() in lookup_pi_state()
futex: Make unlock_pi more robust
rtmutex: Avoid pointless requeueing in the deadlock detection chain walk
rtmutex: Cleanup deadlock detector debug logic
rtmutex: Confine deadlock logic to futex
rtmutex: Simplify remove_waiter()
rtmutex: Document pi chain walk
rtmutex: Clarify the boost/deboost part
rtmutex: No need to keep task ref for lock owner check
rtmutex: Simplify and document try_to_take_rtmutex()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hP9S
-----END PGP SIGNATURE-----
Merge tag 'please-pull-misc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 cleanups from Tony Luck:
"Miscellaneous ia64 specific cleanup"
* tag 'please-pull-misc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] sn: Do not needlessly convert between pointers and integers
[IA64] sn: Fix zeroing of PDAs
Changes include:
- Context tracking support (NO_HZ_FULL) which narrowly missed 3.16
- vDSO layout rework following Andy's work on x86
- TEXT_OFFSET fuzzing for bootloader testing
- /proc/cpuinfo tidy-up
- Preliminary work to support 48-bit virtual addresses, but this is
currently disabled until KVM has been ported to use it (the patches
do, however, bring some nice clean-up)
- Boot-time CPU sanity checks (especially useful on heterogenous
systems)
- Support for syscall auditing
- Support for CC_STACKPROTECTOR
- defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6XMc
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Once again, Catalin's off on holiday and I'm looking after the arm64
tree. Please can you pull the following arm64 updates for 3.17?
Note that this branch also includes the new GICv3 driver (merged via a
stable tag from Jason's irqchip tree), since there is a fix for older
binutils on top.
Changes include:
- context tracking support (NO_HZ_FULL) which narrowly missed 3.16
- vDSO layout rework following Andy's work on x86
- TEXT_OFFSET fuzzing for bootloader testing
- /proc/cpuinfo tidy-up
- preliminary work to support 48-bit virtual addresses, but this is
currently disabled until KVM has been ported to use it (the patches
do, however, bring some nice clean-up)
- boot-time CPU sanity checks (especially useful on heterogenous
systems)
- support for syscall auditing
- support for CC_STACKPROTECTOR
- defconfig updates"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (55 commits)
arm64: add newline to I-cache policy string
Revert "arm64: dmi: Add SMBIOS/DMI support"
arm64: fpsimd: fix a typo in fpsimd_save_partial_state ENDPROC
arm64: don't call break hooks for BRK exceptions from EL0
arm64: defconfig: enable devtmpfs mount option
arm64: vdso: fix build error when switching from LE to BE
arm64: defconfig: add virtio support for running as a kvm guest
arm64: gicv3: Allow GICv3 compilation with older binutils
arm64: fix soft lockup due to large tlb flush range
arm64/crypto: fix makefile rule for aes-glue-%.o
arm64: Do not invoke audit_syscall_* functions if !CONFIG_AUDIT_SYSCALL
arm64: Fix barriers used for page table modifications
arm64: Add support for 48-bit VA space with 64KB page configuration
arm64: asm/pgtable.h pmd/pud definitions clean-up
arm64: Determine the vmalloc/vmemmap space at build time based on VA_BITS
arm64: Clean up the initial page table creation in head.S
arm64: Remove asm/pgtable-*level-types.h files
arm64: Remove asm/pgtable-*level-hwdef.h files
arm64: Convert bool ARM64_x_LEVELS to int ARM64_PGTABLE_LEVELS
arm64: mm: Implement 4 levels of translation tables
...
few days.
MIPS and s390 have little going on this release; just bugfixes, some
small, some larger.
The highlights for x86 are nested VMX improvements (Jan Kiszka), optimizations
for old processor (up to Nehalem, by me and Bandan Das), and a lot of x86
emulator bugfixes (Nadav Amit).
Stephen Rothwell reported a trivial conflict with the tracing branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=UXxV
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM changes from Paolo Bonzini:
"These are the x86, MIPS and s390 changes; PPC and ARM will come in a
few days.
MIPS and s390 have little going on this release; just bugfixes, some
small, some larger.
The highlights for x86 are nested VMX improvements (Jan Kiszka),
optimizations for old processor (up to Nehalem, by me and Bandan Das),
and a lot of x86 emulator bugfixes (Nadav Amit).
Stephen Rothwell reported a trivial conflict with the tracing branch"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (104 commits)
x86/kvm: Resolve shadow warnings in macro expansion
KVM: s390: rework broken SIGP STOP interrupt handling
KVM: x86: always exit on EOIs for interrupts listed in the IOAPIC redir table
KVM: vmx: remove duplicate vmx_mpx_supported() prototype
KVM: s390: Fix memory leak on busy SIGP stop
x86/kvm: Resolve shadow warning from min macro
kvm: Resolve missing-field-initializers warnings
Replace NR_VMX_MSR with its definition
KVM: x86: Assertions to check no overrun in MSR lists
KVM: x86: set rflags.rf during fault injection
KVM: x86: Setting rflags.rf during rep-string emulation
KVM: x86: DR6/7.RTM cannot be written
KVM: nVMX: clean up nested_release_vmcs12 and code around it
KVM: nVMX: fix lifetime issues for vmcs02
KVM: x86: Defining missing x86 vectors
KVM: x86: emulator injects #DB when RFLAGS.RF is set
KVM: x86: Cleanup of rflags.rf cleaning
KVM: x86: Clear rflags.rf on emulated instructions
KVM: x86: popf emulation should not change RF
KVM: x86: Clearing rflags.rf upon skipped emulated instruction
...
to the ftrace function callback infrastructure. It's introducing a
way to allow different functions to call directly different trampolines
instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which always
had a different trampoline, but the function tracer trampoline was called
and did basically nothing, and then the function graph tracer trampoline
was called. The difference now, is that the function graph tracer
trampoline can be called directly if a function is only being traced by
the function graph trampoline. If function tracing is also happening on
the same function, the old way is still done.
The accounting for this takes up more memory when function graph tracing
is activated, as it needs to keep track of which functions it uses.
I have a new way that wont take as much memory, but it's not ready yet
for this merge window, and will have to wait for the next one.
Another big change was the removal of the ftrace_start/stop() calls that
were used by the suspend/resume code that stopped function tracing when
entering into suspend and resume paths. The stop of ftrace was done
because there was some function that would crash the system if one called
smp_processor_id()! The stop/start was a big hammer to solve the issue
at the time, which was when ftrace was first introduced into Linux.
Now ftrace has better infrastructure to debug such issues, and I found
the problem function and labeled it with "notrace" and function tracing
can now safely be activated all the way down into the guts of suspend
and resume.
Other changes include clean ups of uprobe code.
Clean up of the trace_seq() code.
And other various small fixes and clean ups to ftrace and tracing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT35zXAAoJEKQekfcNnQGuOz0H/38zqM0nLFhrgvz3EPk2UOjn
xqpX8qyb2V7TJZL+IqeXU2a5cQZl5ba0D4WtBGpxbTae3CJYiuQ87iKUNFoH0om5
FDpn80igb368k8V3qRdRsziKVCCf0XBd/NkHJXc0ZkfXGyzB2Ga4bBxALxp2gj9y
bnO+vKo6+tWYKG4hyQb4P3LRXUrK8/LWEsPr39cH2QH1Rdj69Lx9CgrCdUVJmwcb
Bj8hEiLXL/RYCFNn79A3wNTUvW0rG/AOIf4SLqXtasSRZ0ToaU0ZyDnrNv+0Ol47
rX8tSk+LfXchL9hpIvjCf1vlAYq3pO02favteR/jip3lx/dTjEDE4RJ9qtJzZ4Q=
=fwQY
-----END PGP SIGNATURE-----
Merge tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This pull request has a lot of work done. The main thing is the
changes to the ftrace function callback infrastructure. It's
introducing a way to allow different functions to call directly
different trampolines instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which
always had a different trampoline, but the function tracer trampoline
was called and did basically nothing, and then the function graph
tracer trampoline was called. The difference now, is that the
function graph tracer trampoline can be called directly if a function
is only being traced by the function graph trampoline. If function
tracing is also happening on the same function, the old way is still
done.
The accounting for this takes up more memory when function graph
tracing is activated, as it needs to keep track of which functions it
uses. I have a new way that wont take as much memory, but it's not
ready yet for this merge window, and will have to wait for the next
one.
Another big change was the removal of the ftrace_start/stop() calls
that were used by the suspend/resume code that stopped function
tracing when entering into suspend and resume paths. The stop of
ftrace was done because there was some function that would crash the
system if one called smp_processor_id()! The stop/start was a big
hammer to solve the issue at the time, which was when ftrace was first
introduced into Linux. Now ftrace has better infrastructure to debug
such issues, and I found the problem function and labeled it with
"notrace" and function tracing can now safely be activated all the way
down into the guts of suspend and resume
Other changes include clean ups of uprobe code, clean up of the
trace_seq() code, and other various small fixes and clean ups to
ftrace and tracing"
* tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
ftrace: Add warning if tramp hash does not match nr_trampolines
ftrace: Fix trampoline hash update check on rec->flags
ring-buffer: Use rb_page_size() instead of open coded head_page size
ftrace: Rename ftrace_ops field from trampolines to nr_trampolines
tracing: Convert local function_graph functions to static
ftrace: Do not copy old hash when resetting
tracing: let user specify tracing_thresh after selecting function_graph
ring-buffer: Always run per-cpu ring buffer resize with schedule_work_on()
tracing: Remove function_trace_stop and HAVE_FUNCTION_TRACE_MCOUNT_TEST
s390/ftrace: remove check of obsolete variable function_trace_stop
arm64, ftrace: Remove check of obsolete variable function_trace_stop
Blackfin: ftrace: Remove check of obsolete variable function_trace_stop
metag: ftrace: Remove check of obsolete variable function_trace_stop
microblaze: ftrace: Remove check of obsolete variable function_trace_stop
MIPS: ftrace: Remove check of obsolete variable function_trace_stop
parisc: ftrace: Remove check of obsolete variable function_trace_stop
sh: ftrace: Remove check of obsolete variable function_trace_stop
sparc64,ftrace: Remove check of obsolete variable function_trace_stop
tile: ftrace: Remove check of obsolete variable function_trace_stop
ftrace: x86: Remove check of obsolete variable function_trace_stop
...
drivers and fixes/enhancements to existing clock drivers. There are also
some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
* improvements to printks on errors
* flattening the previously hierarchal structure of per-clock entries
in debugfs
* allow per-clock debugfs entries that are specific to a particular
clock driver
* configure initial clock parent and/or initial clock rate from Device
Tree
* several feature enhancements to the composite clock type
* misc fixes
New clock drivers added include:
* TI Palmas PMIC
* Allwinner A23 SoC
* Qualcomm APQ8084 and IPQ8064 SoCs
* Rockchip rk3188, rk3066 and rk3288 SoCs
* STMicroelectronics STiH407 SoC
* Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK down"
power saving feature for their Exynos4 & Exynos5 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=48y9
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.17 are mostly additions of new clock
drivers and fixes/enhancements to existing clock drivers. There are
also some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
- improvements to printks on errors
- flattening the previously hierarchal structure of per-clock entries
in debugfs
- allow per-clock debugfs entries that are specific to a particular
clock driver
- configure initial clock parent and/or initial clock rate from
Device Tree
- several feature enhancements to the composite clock type
- misc fixes
New clock drivers added include:
- TI Palmas PMIC
- Allwinner A23 SoC
- Qualcomm APQ8084 and IPQ8064 SoCs
- Rockchip rk3188, rk3066 and rk3288 SoCs
- STMicroelectronics STiH407 SoC
- Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK
down" power saving feature for their Exynos4 & Exynos5 SoCs"
* tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: Add missing of_clk_set_defaults export
clk: checking wrong variable in __set_clk_parents()
clk: Propagate any error return from debug_init()
clk: clps711x: Add DT bindings documentation
clk: Add CLPS711X clk driver
clk: st: Use round to closest divider flag
clk: st: Update frequency tables for fs660c32 and fs432c65
clk: st: STiH407: Support for clockgenA9
clk: st: STiH407: Support for clockgenD0/D2/D3
clk: st: STiH407: Support for clockgenC0
clk: st: Add quadfs reset handling
clk: st: Add polarity bit indication
clk: st: STiH407: Support for clockgenA0
clk: st: STiH407: Support for A9 MUX Clocks
clk: st: STiH407: Support for Flexgen Clocks
clk: st: Adds Flexgen clock binding
clk: st: Remove uncessary (void *) cast
clk: st: use static const for clkgen_pll_data tables
clk: st: use static const for stm_fs tables
clk: st: Update ST clock binding documentation
...
Pull percpu updates from Tejun Heo:
- Major reorganization of percpu header files which I think makes
things a lot more readable and logical than before.
- percpu-refcount is updated so that it requires explicit destruction
and can be reinitialized if necessary. This was pulled into the
block tree to replace the custom percpu refcnting implemented in
blk-mq.
- In the process, percpu and percpu-refcount got cleaned up a bit
* 'for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (21 commits)
percpu-refcount: implement percpu_ref_reinit() and percpu_ref_is_zero()
percpu-refcount: require percpu_ref to be exited explicitly
percpu-refcount: use unsigned long for pcpu_count pointer
percpu-refcount: add helpers for ->percpu_count accesses
percpu-refcount: one bit is enough for REF_STATUS
percpu-refcount, aio: use percpu_ref_cancel_init() in ioctx_alloc()
workqueue: stronger test in process_one_work()
workqueue: clear POOL_DISASSOCIATED in rebind_workers()
percpu: Use ALIGN macro instead of hand coding alignment calculation
percpu: invoke __verify_pcpu_ptr() from the generic part of accessors and operations
percpu: preffity percpu header files
percpu: use raw_cpu_*() to define __this_cpu_*()
percpu: reorder macros in percpu header files
percpu: move {raw|this}_cpu_*() definitions to include/linux/percpu-defs.h
percpu: move generic {raw|this}_cpu_*_N() definitions to include/asm-generic/percpu.h
percpu: only allow sized arch overrides for {raw|this}_cpu_*() ops
percpu: reorganize include/linux/percpu-defs.h
percpu: move accessors from include/linux/percpu.h to percpu-defs.h
percpu: include/asm-generic/percpu.h should contain only arch-overridable parts
percpu: introduce arch_raw_cpu_ptr()
...
Pull crypto update from Herbert Xu:
- CTR(AES) optimisation on x86_64 using "by8" AVX.
- arm64 support to ccp
- Intel QAT crypto driver
- Qualcomm crypto engine driver
- x86-64 assembly optimisation for 3DES
- CTR(3DES) speed test
- move FIPS panic from module.c so that it only triggers on crypto
modules
- SP800-90A Deterministic Random Bit Generator (drbg).
- more test vectors for ghash.
- tweak self tests to catch partial block bugs.
- misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (94 commits)
crypto: drbg - fix failure of generating multiple of 2**16 bytes
crypto: ccp - Do not sign extend input data to CCP
crypto: testmgr - add missing spaces to drbg error strings
crypto: atmel-tdes - Switch to managed version of kzalloc
crypto: atmel-sha - Switch to managed version of kzalloc
crypto: testmgr - use chunks smaller than algo block size in chunk tests
crypto: qat - Fixed SKU1 dev issue
crypto: qat - Use hweight for bit counting
crypto: qat - Updated print outputs
crypto: qat - change ae_num to ae_id
crypto: qat - change slice->regions to slice->region
crypto: qat - use min_t macro
crypto: qat - remove unnecessary parentheses
crypto: qat - remove unneeded header
crypto: qat - checkpatch blank lines
crypto: qat - remove unnecessary return codes
crypto: Resolve shadow warnings
crypto: ccp - Remove "select OF" from Kconfig
crypto: caam - fix DECO RSR polling
crypto: qce - Let 'DEV_QCE' depend on both HAS_DMA and HAS_IOMEM
...
This patch adds common part of dsi node.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This driver is needed by SATA, PCIe and USB modules on TI SoCs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
I don't know if we really need 64 bits here but these variables are
declared as u64 and it can't hurt to cast this so we prevent any shift
wrapping.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Aubrey Li <aubrey.li@linux.intel.com>
Link: http://lkml.kernel.org/r/20140801082715.GE28869@mwanda
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to indicate that this function is converting classic BPF into eBPF
and not related to sockets
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM fixes from Russell King:
"A few fixes for ARM. Some of these are correctness issues:
- TLBs must be flushed after the old mappings are removed by the DMA
mapping code, but before the new mappings are established.
- An off-by-one entry error in the Keystone LPAE setup code.
Fixes include:
- ensuring that the identity mapping for LPAE does not remove the
kernel image from the identity map.
- preventing userspace from trapping into kgdb.
- fixing a preemption issue in the Intel iwmmxt code.
- fixing a build error with nommu.
Other changes include:
- Adding a note about which areas of memory are expected to be
accessible while the identity mapping tables are in place"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8124/1: don't enter kgdb when userspace executes a kgdb break instruction
ARM: idmap: add identity mapping usage note
ARM: 8115/1: LPAE: reduce damage caused by idmap to virtual memory layout
ARM: fix alignment of keystone page table fixup
ARM: 8112/1: only select ARM_PATCH_PHYS_VIRT if MMU is enabled
ARM: 8100/1: Fix preemption disable in iwmmxt_task_enable()
ARM: DMA: ensure that old section mappings are flushed from the TLB
The kgdb breakpoint hooks (kgdb_brk_fn and kgdb_compiled_brk_fn)
should only be entered when a kgdb break instruction is executed
from the kernel. Otherwise, if kgdb is enabled, a userspace program
can cause the kernel to drop into the debugger by executing either
KGDB_BREAKINST or KGDB_COMPILED_BREAK.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a note about the usage of the identity mapping; we do not support
accesses outside of the identity map region and kernel image while a
CPU is using the identity map. This is because the identity mapping
may overwrite vmalloc space, IO mappings, the vectors pages, etc.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add further comments to the early page table remap code to explain what
the code is doing, why it is doing it, but more importantly to explain
that the code is not architecturally compliant and is squarely in
"UNPREDICTABLE" behaviour territory.
Add a warning and tainting of the kernel too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With SCU standby enabled, SCU CLK will be turned off when all processors
are in WFI mode. And the clock will be turned on when any processor
leaves WFI mode.
This behavior should be preferable in terms of power efficiency of
system idle. So let's set the SCU standby bit to enable the support in
function scu_enable().
Cortex-A9 earlier than r2p0 has no standby bit in SCU, so we need to
skip setting the bit for those.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use macro instead of magic number for SCU enable bit.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Common SHA-1 structures are defined in <crypto/sha.h> for code sharing.
This patch changes SHA-1/ARM glue code to use these structures.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull x86 fix from Peter Anvin:
"A single fix to not invoke the espfix code on Xen PV, as it turns out
to oops the guest when invoked after all. This patch leaves some
amount of dead code, in particular unnecessary initialization of the
espfix stacks when they won't be used, but in the interest of keeping
the patch minimal that cleanup can wait for the next cycle"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64/entry/xen: Do not invoke espfix64 on Xen
The bus devices created to be parents for other peripherals
were using platform_bus as a parent, not being platform
devices themselves. Remove the references, making them
virtual devices instead.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since checkin
411cf9ee29 x86, vsmp: Remove is_vsmp_box() from apic_is_clustered_box()
... is_vsmp_box() is only used in vsmp_64.c and does not have any
header file declaring it, so make it explicitly static.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Shai Fultheim <shai@scalemp.com>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1404036068-11674-1-git-send-email-oren@scalemp.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch implements the stack protector code in MIPS compressed boot
phase based on the same code added to arm in commit
8779657d29 "stackprotector: Introduce
CONFIG_CC_STACKPROTECTOR_STRONG" by Kees Cook <keescook@chromium.org>
Signed-off-by: Ben Chan <benchan@chromium.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Olof Johansson <olofj@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7175/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS_CONF4_FTLBSETS_SHIFT define is cut and pasted twice so we can
remove the second define.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-janitors@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7063/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initialise the MAARs such that speculation is enabled for all physical
addresses outside of the I/O region.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add initialisation for Memory Accessibility Attribute Registers. Generic
code cannot know the platform-specific requirements with regards to
speculative accesses, so it simply calls a platform_maar_init function
which platforms with MAARs are expected to implement by calling the
provided write_maar_pair function & returning the number of MAAR pairs
used. A weak default implementation will simply use no MAAR pairs. Any
present but unused MAAR pairs are then marked invalid, effectively
disabling them.
The end result of this patch is that MAARs are all marked invalid, until
platforms implement the platform_maar_init function.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7331/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect the presence of MAAR using the MRP bit in Config5, and record
that presence using a CPU option bit. A cpu_has_maar macro will then
allow code to conditionalise upon the presence of MAARs.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7330/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add accessor macros for the Memory Accessibility Attribute Registers
(MAARs), the bits contained within the MAARs & the Config5.MRP bit
indicating their presence. The only current use of the MAARs is to
enable speculative accesses to regions of memory. Besides the potential
performance benefits of speculative accesses, they are a requirement
for the P5600 core to handle non-128b-aligned MSA vector loads & stores
rather than generating an address error.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7329/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In light of the commit 16f77de82f (Revert "MIPS: Save/restore MSA
context around signals") the MSA support in the kernel is incomplete.
Until the replacement for the former sigcontext changes is agreed upon
and in tree, mark MSA experimental & disable it by default.
MSA is only implemented by one CPU supported by the kernel, the P5600.
The P5600 is a 32 bit core, and thus MSA can only be used when the
experimental CONFIG_MIPS_O32_FP64_SUPPORT option is enabled. Therefore
MSA is only being used in experimental settings anyway and this change
doesn't actually make any difference beyond clarifying the state of
MSA support.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7311/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MSA requires that Status.FR == 1, so for MIPS32 tasks MSA can only be
used if CONFIG_MIPS_O32_FP64_SUPPORT is enabled. If it is not & the
kernel is 32bit, there's no point including support for MSA.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7310/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The TIF_MSA_CTX_LIVE flag (indicating that a task has MSA context which
needs to be preserved) was being cleared in start_thread, but the
TIF_USEDMSA flag (indicating that a task has used MSA in this timeslice)
was not. In copy_thread neither flag was cleared, but both need to be.
Without clearing these flags the kernel will proceed to attempt to save
MSA context when the task is context switched out, and if the task had
not used MSA in the meantime then it will fail because MSA or the FPU
are disabled. The end result is typically:
do_cpu invoked from kernel context![#1]:
CPU: 0 PID: 99 Comm: sh Not tainted 3.16.0-rc4-00025-g6dc9476-dirty #88
task: 8f23dc60 ti: 8f1d8000 task.ti: 8f1d8000
...
Call Trace:
[<8010edbc>] resume+0x5c/0x280
[<80481e0c>] __schedule+0x370/0x800
[<80104838>] work_resched+0x8/0x2c
Fix by consistently clearing both flags in both functions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7309/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MSA specification upon first read appears to suggest that it is safe
to perform vector loads & stores with arbitrary alignment. However it
leaves provision for "address-dependent exceptions"... Align the vector
context to a 16 byte boundary to ensure that the kernel cannot cause any
such exceptions.
Note that the fpu field of struct thread_struct was already at a 16 byte
boundary within the struct, the introduction of FPU_ALIGN simply makes
the requirement explicit. The only part of this impacting the generated
kernel binary is ARCH_MIN_TASKALIGN.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7308/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Preemption must be disabled throughout the process of enabling the FPU,
enabling MSA & initialising the vector registers. Without doing so it
is possible to lose the FPU or MSA whilst initialising them causing
that initialisation to fail.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7307/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel relies upon MSA being disabled when a task begins running,
so that it can initialise or restore context in response to the
resulting MSA disabled exception. Previously the state of MSA following
boot was left as it was before the kernel ran, where MSA could
potentially have been enabled. Explicitly disable it during boot to
prevent any problems.
As a nice side effect the code reads a little better too.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7306/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit d96cc3d1ec "MIPS: Add microMIPS MSA support." attempted to use
the value of a macro within an inline asm statement but instead emitted
a comment leading to the cfcmsa & ctcmsa instructions being omitted. Fix
that by passing CFC_MSA_INSN & CTC_MSA_INSN as arguments to the asm
statements.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7305/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a task does not execute scalar FP instructions prior to using MSA
then the flags indicating that the task has live MSA context were not
being set. The upper 64b of each vector register would then be lost
upon the tasks first context switch after using MSA.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7500/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When a task first makes use of MSA we need to ensure that the upper
64b of the vector registers are set to some value such that no
information can be leaked to it from the previous task to use MSA
context on the CPU. The architecture formerly specified that these
bits would be cleared to 0 when a scalar FP instructions wrote to the
aliased FP registers, which would have implicitly handled this as the
kernel restored scalar FP context. However more recent versions of the
specification now state that the value of the bits in such cases is
unpredictable. Initialise them explictly to be sure, and set all the
bits to 1 rather than 0 for consistency with the least significant
64b.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7497/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel depends upon MSA never being enabled when the FPU is not, a
condition which is currently violated in a few places (whilst saving
sigcontext, following mips_cpu_save). Catch all the problem cases by
disabling MSA in lose_fpu, after saving context if necessary.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7302/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Switching the vector context implicitly saves & restores the state of
the aliased scalar FP data registers, however the scalar FP control
& status register is distinct from the MSA control & status register.
In order to allow scalar FP to function correctly in programs using
MSA, the scalar CSR needs to be saved & restored along with the MSA
vector context.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7301/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I added a field for the MSACSR register in struct mips_fpu_struct, but
never actually made use of it... This is a clear bug. Save and restore
the MSACSR register along with the vector registers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7300/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Just #ifdef away the C functions when included from an assembly file,
as will be done in a following commit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7299/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a definition for D-Link DSR-1000N router. The bootloader on this board
supplies 20006 in the bootinfo; the enum CVMX_BOARD_TYPE_CUST_DSR1000N
comes from the GPL sources of the board.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: David Daney <ddaney.cavm@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Disable HOTPLUG_CPU functionality if the bootloader version is incorrect.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7200/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If nosmp kernel option given, we can assume HOTPLUG_CPU is disabled.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7202/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The same check is already done earlier in octeon_smp_hotplug_setup().
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Patchwork: https://patchwork.linux-mips.org/patch/7199/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GICBIS macro could update the GIC registers incorrectly, depending
on the data value passed in:
* Bits were only OR'd into the register data, so register fields could
not be cleared.
* Bits were OR'd into the register data without masking the data to the
correct field width, corrupting adjacent bits.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7378/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Malta malta_ipi_irqdispatch() routine now checks only IPI interrupts
when handling IPIs. It could previously call do_IRQ() for non-IPIs, and
also call do_IRQ() with an invalid IRQ number if there were no pending
GIC interrupts when gic_get_int() was called.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7377/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move most of the functionality of gic_get_int() into a new function
gic_get_int_mask() which takes a bitmask of interrupts in which the
caller is interested, and returns the subset which are pending for the
current CPU.
This allows CP0 IRQ dispatch routines to check only the GIC interrupts
which are routed to a particular CPU interrupt input.
gic_get_int() is reimplemented using gic_get_int_mask() and is retained
for use by any platforms for which gic_get_int() is sufficient.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7376/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A GIC interrupt which is declared as having a GIC_MAP_TO_NMI_MSK
mapping causes the cpu parameter to gic_setup_intr() to be increased
to 32, causing memory corruption when pcpu_masks[] is written to again
later in the function.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7375/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
irq-gic.c:gic_get_int() masks out interrupts from the pending set which
aren’t in the pcpu_mask. Only interrupts marked with GIC_FLAG_IPI were
set in pcpu_mask, meaning that peripheral interrupts also had to be
marked as IPIs. Remove the use of GIC_FLAG_IPI and allow the flags
member of struct gic_intr_map to be zero.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7374/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The value of GIC_NUM_INTRS is platform-specific. Using a default value
from gic.h will result in incorrect behaviour on some systems, so
require a suitable definition to be present in the platform's irq.h.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7373/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several bitmaps are declared in arch/mips/include/asm/gic.h, but the
scope of their use is limited to arch/mips/kernel/irq-gic.c. Move the
declarations from the header file to the C file.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7372/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect if the core supports unique exception codes for the
Read-Inhibit and Execute-Inhibit exceptions and set the
option accordingly. The RI/XI exception support is detected
by setting the 27th bit (IEC) of the PageGrain C0 register
and reading back the value of that register to verify the
bit is enabled.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7340/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the regular tlb_do_page_fault_0 (no write) handler to handle
the RI and XI exceptions. Also skip the RI/XI validation check
on TLB load handler since it's redundant when the CPU has
unique RI/XI exceptions.
Singed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7339/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPSr5 added support for unique exception codes for the Read-Inhibit
and Execute-Inhibit exceptions.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Hardware Page Table Walker aims to speed up TLB refill exceptions
by handling them in the hardware level instead of having a software
TLB refill handler. However, a TLB refill exception can still be
thrown in certain cases such as, synchronus exceptions, or address
translation or memory errors during the HTW operation. As a result of
which, HTW must not be considered a complete replacement for the TLB
refill software handler, but rather a fast-path for it.
For HTW to work, the PWBase register must contain the task's page
global directory address so the HTW will kick in on TLB refill
exceptions.
Due to HTW being a separate engine embedded deep in the CPU pipeline,
we need to restart the HTW everytime a PTE changes to avoid HTW
fetching a old entry from the page tables. It's also necessary to
restart the HTW on context switches to prevent it from fetching a
page from the previous process. Finally, since HTW is using the
entryhi register to write the translations to the TLB, it's necessary
to stop the HTW whenever the entryhi changes (eg for tlb probe
perations) and enable it back afterwards.
== Performance ==
The following trivial test was used to measure the performance of the
HTW. Using the same root filesystem, the following command was used
to measure the number of tlb refill handler executions with and
without (using 'nohtw' kernel parameter) HTW support. The kernel was
modified to use a scratch register as a counter for the TLB refill
exceptions.
find /usr -type f -exec ls -lh {} \;
HTW Enabled:
TLB refill exceptions: 12306
HTW Disabled:
TLB refill exceptions: 17805
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/7336/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect if the core implements the HTW and set the option accordingly.
Also, add a new kernel parameter called 'nohtw' allowing
the user to disable the htw support and fallback to the software
refill handler.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7335/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Moreover, report hardware page table walker support as 'htw' in the ASE
list of /proc/cpuinfo, if the core implements this feature.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Long integers which are 4 bytes in MIPS32 can't hold new CPU
options anymore, so the type of the 'options' variable is changed
to unsigned long long which allows 32 more cpu options to be defined
for MIPS32
Also, re-arrange the 'options' struct member to avoid potential 4-byte
alignment gap in the middle of the struct.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7324/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add cases in perf_event_mipsxx.c for CPU_P5600. All the event numbers
listed for proAptiv also apply to P5600, so we use mipsxxcore_event_map2
and mipsxxcore_cache_map2 too, but the P5600 has 8-bit event numbers so
bit 8 (256) of the user ABI config is used for the parity bit (to
specify odd/even counter events).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7242/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In mipsxx_pmu_map_raw_event(), set event_id to base_id after the cpu
type conditional code to allow that code to override the base_id to use
more bits from the config and a higher bit for parity.
This will allow cores with up to 512 events between all even/odd
counters (an 8-bit event id) such as P5600 to use bit 8 for parity.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7243/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This header defines an exported interface (the register layout used in
core dumps and the GP regset accessible with PTRACE_{GET,SET}REGSET),
therefore belongs in uapi.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7458/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The struct user definition in this file is not used anywhere (the ELF
core dumper does not use that format). Therefore, remove the header and
instead enable the asm-generic user.h which is an empty header to
satisfy a few generic headers which still try to include user.h.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7459/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the core dumper now uses regsets, the old core dump functions are
now unused. Remove them.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7456/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In uapi/asm/ptrace.h, a user version of pt_regs is defined wrapped in
ifndef __KERNEL__. This structure definition does not match anything
used by any kernel API, in particular it does not match the format used
by PTRACE_{GET,SET}REGS.
Therefore, replace the structure definition with one matching what is
used by PTRACE_{GET,SET}REGS. The format used by these is the same for
both 32-bit and 64-bit.
Also, change the implementation of PTRACE_{GET,SET}REGS to use this new
structure definition. The structure is renamed to user_pt_regs when
__KERNEL__ is defined to avoid conflicts with the kernel's own pt_regs.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7457/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A comment in the O32/32-bit system call code is incorrect since commit
46e12c07b3 ("MIPS: O32 / 32-bit: Always copy 4 stack arguments.").
Remove it.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7455/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On 32-bit/O32, pt_regs has a padding area at the beginning into which the
syscall arguments passed via the user stack are copied. 4 arguments
totalling 16 bytes are copied to offset 16 bytes into this area, however
the area is only 24 bytes long. This means the last 2 arguments overwrite
pt_regs->regs[{0,1}].
If a syscall function returns an error, handle_sys stores the original
syscall number in pt_regs->regs[0] for syscall restart. signal.c checks
whether regs[0] is non-zero, if it is it will check whether the syscall
return value is one of the ERESTART* codes to see if it must be
restarted.
Should a syscall be made that results in a non-zero value being copied
off the user stack into regs[0], and then returns a positive (non-error)
value that matches one of the ERESTART* error codes, this can be mistaken
for requiring a syscall restart.
While the possibility for this to occur has always existed, it is made
much more likely to occur by commit 46e12c07b3 ("MIPS: O32 / 32-bit:
Always copy 4 stack arguments."), since now every syscall will copy 4
arguments and overwrite regs[0], rather than just those with 7 or 8
arguments.
Since that commit, booting Debian under a 32-bit MIPS kernel almost
always results in a hang early in boot, due to a wait4 syscall returning
a PID that matches one of the ERESTART* codes, which then causes an
incorrect restart of the syscall.
The problem is fixed by increasing the size of the padding area so that
arguments copied off the stack will not overwrite pt_regs->regs[{0,1}].
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7454/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A DT bugfix for Nomadik that had an ambigouos double-inversion of a gpio
line, and one MAINTAINER URL update that might as well go in now.
We could hold off until the merge window, but then we'll just have to mark
the DT fix for stable and it just seems like in total causing more work.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=sz9W
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM straggler SoC fix from Olof Johansson:
"A DT bugfix for Nomadik that had an ambigouos double-inversion of a
gpio line, and one MAINTAINER URL update that might as well go in now.
We could hold off until the merge window, but then we'll just have to
mark the DT fix for stable and it just seems like in total causing
more work"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Update Tegra Git URL
ARM: nomadik: fix up double inversion in DT
not boot since 3.6-rc1. The problem is that user_addr_max returned the biggest
available RAM address which makes some copy_from_user variants fail to read
from XIP memory.
Even in the presence of one of the two fixes the other still makes sense, so
both patches are included here.
This problem was the last one preventing efm32 boot to a prompt with mainline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlOyfhsACgkQ6suMTIUe0hZWggCePaoe/S+aDki9B2ASCY0zVkRq
XE8AoM5G4yRgnL3zitI2ftvvlp4xx1mS
=4Vjn
-----END PGP SIGNATURE-----
Merge tag 'nommu-for-rmk' of git://git.pengutronix.de/git/ukl/linux into devel-stable
Two different fixes for the same problem making some ARM nommu configurations
not boot since 3.6-rc1. The problem is that user_addr_max returned the biggest
available RAM address which makes some copy_from_user variants fail to read
from XIP memory.
Even in the presence of one of the two fixes the other still makes sense, so
both patches are included here.
This problem was the last one preventing efm32 boot to a prompt with mainline.
Commit
Commit 1d40cfcd34
Author: Ralf Baechle <ralf@linux-mips.org>
Date: Fri Jul 15 15:23:23 2005 +0000
Avoid SMP cacheflushes. This is a minor optimization of startup but
will also avoid smp_call_function from doing stupid things when called
from a CPU that is not yet marked online.
missed an appropriate cache flush of TLB refill handler because that time it was
at fixed location CAC_BASE. After years the refill handler in EBASE vector
is not at that location and can be allocated in some another memory and needs
I-cache sync as other TLB exception vectors.
Besides that, the new function - local_flash_icache_range() was introduced
to avoid SMP cacheflushes.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: paul.gortmaker@windriver.com
Cc: jchandra@broadcom.com
Cc: linux-kernel@vger.kernel.org
Cc: david.daney@cavium.com
Patchwork: https://patchwork.linux-mips.org/patch/7312/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rename usb_nop_xceiv to usb_phy_generic in platform data to match the
name change of the nop transceiver driver in commit 4525bee (usb: phy:
rename usb_nop_xceiv to usb_phy_generic).
The name change induced a kernel panic due to an unhandled kernel
unaligned access while trying to dereference musb->xceiv->io_ops in
musb_init_controller().
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: John Crispin <blogic@openwrt.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7263/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit d6d3c9afaa (MIPS: MT: proc: Add support for printing VPE and TC
ids) causes a link error when CONFIG_PROC_FS=n:
arch/mips/built-in.o: In function `proc_cpuinfo_notifier_init':
smp-mt.c: undefined reference to `register_proc_cpuinfo_notifier'
This is fixed by adding an ifdef around the procfs handling code
in smp-mt.c.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reported-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # >= 3.15
Patchwork: https://patchwork.linux-mips.org/patch/7244/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The IP_PKTOPTIONS sockopt puts control messages in option_values, these
need to be handled differently in the compat case. This is already done
through the MSG_CMSG_COMPAT flag, we just need to use
compat_sys_getsockopt which sets that flag.
Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7115/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a call to device_create() fails for a channel during the initialize
loop, we need to clean the devices entries already created before
leaving.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Qais Yousef <Qais.Yousef@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Patchwork: https://patchwork.linux-mips.org/patch/7111/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Due to a missing newline in the I-cache policy detection log output,
it's possible to get some ratehr unfortunate output at boot time:
CPU1: Booted secondary processor
Detected VIPT I-cache on CPU1CPU2: Booted secondary processor
Detected VIPT I-cache on CPU2CPU3: Booted secondary processor
Detected VIPT I-cache on CPU3CPU4: Booted secondary processor
Detected PIPT I-cache on CPU4CPU5: Booted secondary processor
Detected PIPT I-cache on CPU5Brought up 6 CPUs
SMP: Total of 6 processors activated.
This patch adds the missing newline to the format string, cleaning up
the output.
Fixes: 59ccc0d41b ("arm64: cachetype: report weakest cache policy")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The large segment table entry format has block of bits for the
ACC/F values for the large page. These bits are valid only if
another bit (AV bit 0x10000) of the segment table entry is set.
The ACC/F bits do not have a meaning if the AV bit is off.
This allows to put the THP splitting bit, the segment young bit
and the new segment dirty bit into the ACC/F bits as long as
the AV bit stays off. The dirty and young information is only
available if the pmd is large.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit f0a3eaff71 (ARM64: KVM: fix big endian issue in
access_vm_reg for 32bit guest) changed the way we handle CP15
VM accesses, so that all 64bit accesses are done via vcpu_sys_reg.
This looks like a good idea as it solves indianness issues in an
elegant way, except for one small detail: the register index is
doesn't refer to the same array! We end up corrupting some random
data structure instead.
Fix this by reverting to the original code, except for the introduction
of a vcpu_cp15_64_high macro that deals with the endianness thing.
Tested on Juno with 32bit SMP guests.
Cc: Victor Kamensky <victor.kamensky@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
commit ec66ad66a0 (s390/mm: enable
split page table lock for PMD level) activated the split pmd lock
for s390. Turns out that we missed one place: We also have to take
the pmd lock instead of the page table lock when we reallocate the
page tables (==> changing entries in the PMD) during sie enablement.
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix coding style problems in arch/arm/mach-omap2/control.c.
Signed-off-by: Jeremy Vial <jvial@adeneo-embedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the comment “restore_es3: applies to 34xx >= ES3.0" in
"arch/arm/mach-omap2/sleep34xx.S”, omap3_restore_es3 should be used
if the revision of an OMAP34xx is ES3.1.2.
Signed-off-by: Jeremy Vial <jvial@adeneo-embedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is based on tags/exynos-power because this DT changes
are depending PMU cleanup.
Fixes boot for exynos5260 and exynos5410,
- Since exynos cannot boot without obtaining PMU address via
DT from now on, add PMU node for exynos5260 and exynos5410
For preparing exynos5250-spring,
- move max77686 and cypress,cyapa trackpad from exynos5250-
cros-common to exynos5250-snow DT file
(Note exynos5250-spring is not included in this branch yet)
For exynos3250,
- add TMU node and remove duplicated interrupt-parent
- add missing pinctrl property for uart0 and uart1
For exynos5250-smdk5250 board
- add max77686 pmic interrupt property which is connected to
gpx3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aXEe
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT 2nd updates for v3.17" from Kukjin Kim:
This is based on tags/exynos-power because this DT changes
are depending PMU cleanup.
Fixes boot for exynos5260 and exynos5410,
- Since exynos cannot boot without obtaining PMU address via
DT from now on, add PMU node for exynos5260 and exynos5410
For preparing exynos5250-spring,
- move max77686 and cypress,cyapa trackpad from exynos5250-
cros-common to exynos5250-snow DT file
(Note exynos5250-spring is not included in this branch yet)
For exynos3250,
- add TMU node and remove duplicated interrupt-parent
- add missing pinctrl property for uart0 and uart1
For exynos5250-smdk5250 board
- add max77686 pmic interrupt property which is connected to
gpx3
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (28 commits)
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
ARM: dts: Document exynos5410 PMU
ARM: EXYNOS: Move cpufreq and cpuidle device registration to init_machine
ARM: EXYNOS: Refactored code for using PMU address via DT
ARM: EXYNOS: Support cluster power off on exynos5420/5800
ARM: EXYNOS: populate suspend and powered_up callbacks for mcpm
ARM: EXYNOS: do not allow cpuidle registration for exynos5420
cpuidle: big.LITTLE: init driver for exynos5420
cpuidle: big.LITTLE: Add ARCH_EXYNOS entry in config
ARM: EXYNOS: add generic function to calculate cpu number
cpuidle: big.LITTLE: add of_device_id structure
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds socfpga Ethernet filter attributes for multicast
and unicast filters per Synopsys Ethernet IP configuration chosen
by Altera for the Cyclone 5 and Arria SOC FPGAs.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing a debug message for setting the identity map since it becomes
rather noisy after rework of the identity map code.
Signed-off-by: Matthew Rushton <mrushton@amazon.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
This has been run through Intel's LKP tests across a wide range
of modern sytems and workloads and it wasn't shown to make a
measurable performance difference positive or negative.
Now that we have some shiny new tracepoints, we can actually
figure out what the heck is going on.
During a kernel compile, 60% of the flush_tlb_mm_range() calls
are for a single page. It breaks down like this:
size percent percent<=
V V V
GLOBAL: 2.20% 2.20% avg cycles: 2283
1: 56.92% 59.12% avg cycles: 1276
2: 13.78% 72.90% avg cycles: 1505
3: 8.26% 81.16% avg cycles: 1880
4: 7.41% 88.58% avg cycles: 2447
5: 1.73% 90.31% avg cycles: 2358
6: 1.32% 91.63% avg cycles: 2563
7: 1.14% 92.77% avg cycles: 2862
8: 0.62% 93.39% avg cycles: 3542
9: 0.08% 93.47% avg cycles: 3289
10: 0.43% 93.90% avg cycles: 3570
11: 0.20% 94.10% avg cycles: 3767
12: 0.08% 94.18% avg cycles: 3996
13: 0.03% 94.20% avg cycles: 4077
14: 0.02% 94.23% avg cycles: 4836
15: 0.04% 94.26% avg cycles: 5699
16: 0.06% 94.32% avg cycles: 5041
17: 0.57% 94.89% avg cycles: 5473
18: 0.02% 94.91% avg cycles: 5396
19: 0.03% 94.95% avg cycles: 5296
20: 0.02% 94.96% avg cycles: 6749
21: 0.18% 95.14% avg cycles: 6225
22: 0.01% 95.15% avg cycles: 6393
23: 0.01% 95.16% avg cycles: 6861
24: 0.12% 95.28% avg cycles: 6912
25: 0.05% 95.32% avg cycles: 7190
26: 0.01% 95.33% avg cycles: 7793
27: 0.01% 95.34% avg cycles: 7833
28: 0.01% 95.35% avg cycles: 8253
29: 0.08% 95.42% avg cycles: 8024
30: 0.03% 95.45% avg cycles: 9670
31: 0.01% 95.46% avg cycles: 8949
32: 0.01% 95.46% avg cycles: 9350
33: 3.11% 98.57% avg cycles: 8534
34: 0.02% 98.60% avg cycles: 10977
35: 0.02% 98.62% avg cycles: 11400
We get in to dimishing returns pretty quickly. On pre-IvyBridge
CPUs, we used to set the limit at 8 pages, and it was set at 128
on IvyBrige. That 128 number looks pretty silly considering that
less than 0.5% of the flushes are that large.
The previous code tried to size this number based on the size of
the TLB. Good idea, but it's error-prone, needs maintenance
(which it didn't get up to now), and probably would not matter in
practice much.
Settting it to 33 means that we cover the mallopt
M_TRIM_THRESHOLD, which is the most universally common size to do
flushes.
That's the short version. Here's the long one for why I chose 33:
1. These numbers have a constant bias in the timestamps from the
tracing. Probably counts for a couple hundred cycles in each of
these tests, but it should be fairly _even_ across all of them.
The smallest delta between the tracepoints I have ever seen is
335 cycles. This is one reason the cycles/page cost goes down in
general as the flushes get larger. The true cost is nearer to
100 cycles.
2. A full flush is more expensive than a single invlpg, but not
by much (single percentages).
3. A dtlb miss is 17.1ns (~45 cycles) and a itlb miss is 13.0ns
(~34 cycles). At those rates, refilling the 512-entry dTLB takes
22,000 cycles.
4. 22,000 cycles is approximately the equivalent of doing 85
invlpg operations. But, the odds are that the TLB can
actually be filled up faster than that because TLB misses that
are close in time also tend to leverage the same caches.
6. ~98% of flushes are <=33 pages. There are a lot of flushes of
33 pages, probably because libc's M_TRIM_THRESHOLD is set to
128k (32 pages)
7. I've found no consistent data to support changing the IvyBridge
vs. SandyBridge tunable by a factor of 16
I used the performance counters on this hardware (IvyBridge i5-3320M)
to figure out the tlb miss costs:
ocperf.py stat -e dtlb_load_misses.walk_duration,dtlb_load_misses.walk_completed,dtlb_store_misses.walk_duration,dtlb_store_misses.walk_completed,itlb_misses.walk_duration,itlb_misses.walk_completed,itlb.itlb_flush
7,720,030,970 dtlb_load_misses_walk_duration [57.13%]
169,856,353 dtlb_load_misses_walk_completed [57.15%]
708,832,859 dtlb_store_misses_walk_duration [57.17%]
19,346,823 dtlb_store_misses_walk_completed [57.17%]
2,779,687,402 itlb_misses_walk_duration [57.15%]
82,241,148 itlb_misses_walk_completed [57.13%]
770,717 itlb_itlb_flush [57.11%]
Show that a dtlb miss is 17.1ns (~45 cycles) and a itlb miss is 13.0ns
(~34 cycles). At those rates, refilling the 512-entry dTLB takes
22,000 cycles. On a SandyBridge system with more cores and larger
caches, those are dtlb=13.4ns and itlb=9.5ns.
cat perf.stat.txt | perl -pe 's/,//g'
| awk '/itlb_misses_walk_duration/ { icyc+=$1 }
/itlb_misses_walk_completed/ { imiss+=$1 }
/dtlb_.*_walk_duration/ { dcyc+=$1 }
/dtlb_.*.*completed/ { dmiss+=$1 }
END {print "itlb cyc/miss: ", icyc/imiss, " dtlb cyc/miss: ", dcyc/dmiss, " ----- ", icyc,imiss, dcyc,dmiss }
On Westmere CPUs, the counters to use are: itlb_flush,itlb_misses.walk_cycles,itlb_misses.any,dtlb_misses.walk_cycles,dtlb_misses.any
The assumptions that this code went in under:
https://lkml.org/lkml/2012/6/12/119 say that a flush and a refill are
about 100ns. Being generous, that is over by a factor of 6 on the
refill side, although it is fairly close on the cost of an invlpg.
An increase of a single invlpg operation seems to lengthen the flush
range operation by about 200 cycles. Here is one example of the data
collected for flushing 10 and 11 pages (full data are below):
10: 0.43% 93.90% avg cycles: 3570 cycles/page: 357 samples: 4714
11: 0.20% 94.10% avg cycles: 3767 cycles/page: 342 samples: 2145
How to generate this table:
echo 10000 > /sys/kernel/debug/tracing/buffer_size_kb
echo x86-tsc > /sys/kernel/debug/tracing/trace_clock
echo 'reason != 0' > /sys/kernel/debug/tracing/events/tlb/tlb_flush/filter
echo 1 > /sys/kernel/debug/tracing/events/tlb/tlb_flush/enable
Pipe the trace output in to this script:
http://sr71.net/~dave/intel/201402-tlb/trace-time-diff-process.pl.txt
Note that these data were gathered with the invlpg threshold set to
150 pages. Only data points with >=50 of samples were printed:
Flush % of %<=
in flush this
pages es size
------------------------------------------------------------------------------
-1: 2.20% 2.20% avg cycles: 2283 cycles/page: xxxx samples: 23960
1: 56.92% 59.12% avg cycles: 1276 cycles/page: 1276 samples: 620895
2: 13.78% 72.90% avg cycles: 1505 cycles/page: 752 samples: 150335
3: 8.26% 81.16% avg cycles: 1880 cycles/page: 626 samples: 90131
4: 7.41% 88.58% avg cycles: 2447 cycles/page: 611 samples: 80877
5: 1.73% 90.31% avg cycles: 2358 cycles/page: 471 samples: 18885
6: 1.32% 91.63% avg cycles: 2563 cycles/page: 427 samples: 14397
7: 1.14% 92.77% avg cycles: 2862 cycles/page: 408 samples: 12441
8: 0.62% 93.39% avg cycles: 3542 cycles/page: 442 samples: 6721
9: 0.08% 93.47% avg cycles: 3289 cycles/page: 365 samples: 917
10: 0.43% 93.90% avg cycles: 3570 cycles/page: 357 samples: 4714
11: 0.20% 94.10% avg cycles: 3767 cycles/page: 342 samples: 2145
12: 0.08% 94.18% avg cycles: 3996 cycles/page: 333 samples: 864
13: 0.03% 94.20% avg cycles: 4077 cycles/page: 313 samples: 289
14: 0.02% 94.23% avg cycles: 4836 cycles/page: 345 samples: 236
15: 0.04% 94.26% avg cycles: 5699 cycles/page: 379 samples: 390
16: 0.06% 94.32% avg cycles: 5041 cycles/page: 315 samples: 643
17: 0.57% 94.89% avg cycles: 5473 cycles/page: 321 samples: 6229
18: 0.02% 94.91% avg cycles: 5396 cycles/page: 299 samples: 224
19: 0.03% 94.95% avg cycles: 5296 cycles/page: 278 samples: 367
20: 0.02% 94.96% avg cycles: 6749 cycles/page: 337 samples: 185
21: 0.18% 95.14% avg cycles: 6225 cycles/page: 296 samples: 1964
22: 0.01% 95.15% avg cycles: 6393 cycles/page: 290 samples: 83
23: 0.01% 95.16% avg cycles: 6861 cycles/page: 298 samples: 61
24: 0.12% 95.28% avg cycles: 6912 cycles/page: 288 samples: 1307
25: 0.05% 95.32% avg cycles: 7190 cycles/page: 287 samples: 533
26: 0.01% 95.33% avg cycles: 7793 cycles/page: 299 samples: 94
27: 0.01% 95.34% avg cycles: 7833 cycles/page: 290 samples: 66
28: 0.01% 95.35% avg cycles: 8253 cycles/page: 294 samples: 73
29: 0.08% 95.42% avg cycles: 8024 cycles/page: 276 samples: 846
30: 0.03% 95.45% avg cycles: 9670 cycles/page: 322 samples: 296
31: 0.01% 95.46% avg cycles: 8949 cycles/page: 288 samples: 79
32: 0.01% 95.46% avg cycles: 9350 cycles/page: 292 samples: 60
33: 3.11% 98.57% avg cycles: 8534 cycles/page: 258 samples: 33936
34: 0.02% 98.60% avg cycles: 10977 cycles/page: 322 samples: 268
35: 0.02% 98.62% avg cycles: 11400 cycles/page: 325 samples: 177
36: 0.01% 98.63% avg cycles: 11504 cycles/page: 319 samples: 161
37: 0.02% 98.65% avg cycles: 11596 cycles/page: 313 samples: 182
38: 0.02% 98.66% avg cycles: 11850 cycles/page: 311 samples: 195
39: 0.01% 98.68% avg cycles: 12158 cycles/page: 311 samples: 128
40: 0.01% 98.68% avg cycles: 11626 cycles/page: 290 samples: 78
41: 0.04% 98.73% avg cycles: 11435 cycles/page: 278 samples: 477
42: 0.01% 98.73% avg cycles: 12571 cycles/page: 299 samples: 74
43: 0.01% 98.74% avg cycles: 12562 cycles/page: 292 samples: 78
44: 0.01% 98.75% avg cycles: 12991 cycles/page: 295 samples: 108
45: 0.01% 98.76% avg cycles: 13169 cycles/page: 292 samples: 78
46: 0.02% 98.78% avg cycles: 12891 cycles/page: 280 samples: 261
47: 0.01% 98.79% avg cycles: 13099 cycles/page: 278 samples: 67
48: 0.01% 98.80% avg cycles: 13851 cycles/page: 288 samples: 77
49: 0.01% 98.80% avg cycles: 13749 cycles/page: 280 samples: 66
50: 0.01% 98.81% avg cycles: 13949 cycles/page: 278 samples: 73
52: 0.00% 98.82% avg cycles: 14243 cycles/page: 273 samples: 52
54: 0.01% 98.83% avg cycles: 15312 cycles/page: 283 samples: 87
55: 0.01% 98.84% avg cycles: 15197 cycles/page: 276 samples: 109
56: 0.02% 98.86% avg cycles: 15234 cycles/page: 272 samples: 208
57: 0.00% 98.86% avg cycles: 14888 cycles/page: 261 samples: 53
58: 0.01% 98.87% avg cycles: 15037 cycles/page: 259 samples: 59
59: 0.01% 98.87% avg cycles: 15752 cycles/page: 266 samples: 63
62: 0.00% 98.89% avg cycles: 16222 cycles/page: 261 samples: 54
64: 0.02% 98.91% avg cycles: 17179 cycles/page: 268 samples: 248
65: 0.12% 99.03% avg cycles: 18762 cycles/page: 288 samples: 1324
85: 0.00% 99.10% avg cycles: 21649 cycles/page: 254 samples: 50
127: 0.01% 99.18% avg cycles: 32397 cycles/page: 255 samples: 75
128: 0.13% 99.31% avg cycles: 31711 cycles/page: 247 samples: 1466
129: 0.18% 99.49% avg cycles: 33017 cycles/page: 255 samples: 1927
181: 0.33% 99.84% avg cycles: 2489 cycles/page: 13 samples: 3547
256: 0.05% 99.91% avg cycles: 2305 cycles/page: 9 samples: 550
512: 0.03% 99.95% avg cycles: 2133 cycles/page: 4 samples: 304
1512: 0.01% 99.99% avg cycles: 3038 cycles/page: 2 samples: 65
Here are the tlb counters during a 10-second slice of a kernel compile
for a SandyBridge system. It's better than IvyBridge, but probably
due to the larger caches since this was one of the 'X' extreme parts.
10,873,007,282 dtlb_load_misses_walk_duration
250,711,333 dtlb_load_misses_walk_completed
1,212,395,865 dtlb_store_misses_walk_duration
31,615,772 dtlb_store_misses_walk_completed
5,091,010,274 itlb_misses_walk_duration
163,193,511 itlb_misses_walk_completed
1,321,980 itlb_itlb_flush
10.008045158 seconds time elapsed
# cat perf.stat.1392743721.txt | perl -pe 's/,//g' | awk '/itlb_misses_walk_duration/ { icyc+=$1 } /itlb_misses_walk_completed/ { imiss+=$1 } /dtlb_.*_walk_duration/ { dcyc+=$1 } /dtlb_.*.*completed/ { dmiss+=$1 } END {print "itlb cyc/miss: ", icyc/imiss/3.3, " dtlb cyc/miss: ", dcyc/dmiss/3.3, " ----- ", icyc,imiss, dcyc,dmiss }'
itlb ns/miss: 9.45338 dtlb ns/miss: 12.9716
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154103.10C1115E@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Most of the logic here is in the documentation file. Please take
a look at it.
I know we've come full-circle here back to a tunable, but this
new one is *WAY* simpler. I challenge anyone to describe in one
sentence how the old one worked. Here's the way the new one
works:
If we are flushing more pages than the ceiling, we use
the full flush, otherwise we use per-page flushes.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154101.12B52CAF@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We don't have any good way to figure out what kinds of flushes
are being attempted. Right now, we can try to use the vm
counters, but those only tell us what we actually did with the
hardware (one-by-one vs full) and don't tell us what was actually
_requested_.
This allows us to select out "interesting" TLB flushes that we
might want to optimize (like the ranged ones) and ignore the ones
that we have very little control over (the ones at context
switch).
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154059.4C96CBA5@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There are currently three paths through the remote flush code:
1. full invalidation
2. single page invalidation using invlpg
3. ranged invalidation using invlpg
This takes 2 and 3 and combines them in to a single path by
making the single-page one just be the start and end be start
plus a single page. This makes placement of our tracepoint easier.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154058.E0F90408@viggo.jf.intel.com
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If we take the
if (end == TLB_FLUSH_ALL || vmflag & VM_HUGETLB) {
local_flush_tlb();
goto out;
}
path out of flush_tlb_mm_range(), we will have flushed the tlb,
but not incremented NR_TLB_LOCAL_FLUSH_ALL. This unifies the
way out of the function so that we always take a single path when
doing a full tlb flush.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154056.FF763B76@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
I think the flush_tlb_mm_range() code that tries to tune the
flush sizes based on the CPU needs to get ripped out for
several reasons:
1. It is obviously buggy. It uses mm->total_vm to judge the
task's footprint in the TLB. It should certainly be using
some measure of RSS, *NOT* ->total_vm since only resident
memory can populate the TLB.
2. Haswell, and several other CPUs are missing from the
intel_tlb_flushall_shift_set() function. Thus, it has been
demonstrated to bitrot quickly in practice.
3. It is plain wrong in my vm:
[ 0.037444] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.037444] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.037444] tlb_flushall_shift: 6
Which leads to it to never use invlpg.
4. The assumptions about TLB refill costs are wrong:
http://lkml.kernel.org/r/1337782555-8088-3-git-send-email-alex.shi@intel.com
(more on this in later patches)
5. I can not reproduce the original data: https://lkml.org/lkml/2012/5/17/59
I believe the sample times were too short. Running the
benchmark in a loop yields times that vary quite a bit.
Note that this leaves us with a static ceiling of 1 page. This
is a conservative, dumb setting, and will be revised in a later
patch.
This also removes the code which attempts to predict whether we
are flushing data or instructions. We expect instruction flushes
to be relatively rare and not worth tuning for explicitly.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154055.ABC88E89@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The
if (cpumask_any_but(mm_cpumask(mm), smp_processor_id()) < nr_cpu_ids)
line of code is not exactly the easiest to audit, especially when
it ends up at two different indentation levels. This eliminates
one of the the copy-n-paste versions. It also gives us a unified
exit point for each path through this function. We need this in
a minute for our tracepoint.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154054.44F1CDDC@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Since commit b5660ba76b ("x86, platforms: Remove NUMAQ") removed NUMAQ,
the mps_oem_check() apic callback has been obsolete. Remove it.
This allows generic_mps_oem_check() to be removed as well.
Signed-off-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1407302349390.17503@chino.kir.corp.google.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The trampoline_phys_{high,low} members of struct apic are always
initialized to DEFAULT_TRAMPOLINE_PHYS_HIGH and TRAMPOLINE_PHYS_LOW,
respectively. Hardwire the constants and remove the unneeded members.
Signed-off-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1407302348330.17503@chino.kir.corp.google.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Resolve shadow warnings that appear in W=2 builds. Instead of
using ret to hold the return pointer, save the length in a new
variable saved_len and compute the pointer on exit. This also
resolves a very technical error, in that ret was declared as
a const char *, when it really was a char * const.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- a memory leak on busy SIGP
- pontentially lost SIGP stop in rare situations (shutdown loops)
The first issue is not part of a released kernel. The 2nd issue is
present in all KVM versions, but did not trigger before commit
7dfc63cf97 (KVM: s390: allow only one SIGP STOP
(AND STORE STATUS) at a time) with Linux as a guest.
So no need for cc stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=+xZE
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-20140730' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-next
Two fixes for recently introduced regressions
- a memory leak on busy SIGP
- pontentially lost SIGP stop in rare situations (shutdown loops)
The first issue is not part of a released kernel. The 2nd issue is
present in all KVM versions, but did not trigger before commit
7dfc63cf97 (KVM: s390: allow only one SIGP STOP
(AND STORE STATUS) at a time) with Linux as a guest.
So no need for cc stable
Commit 72c5839515 (arm64: gicv3: Allow GICv3 compilation with
older binutils) changed the way we express the GICv3 system registers,
but couldn't change the occurences used by KVM as the code wasn't
merged yet.
Just fix the accessors.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This reverts commit a28e3f4b90.
Ard and Yi Li report that this patch is broken by design, so revert it
and let them sort it out for 3.18 instead.
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A GIC interrupt which is declared as having a GIC_MAP_TO_NMI_MSK
mapping causes the cpu parameter to gic_setup_intr() to be increased
to 32, causing memory corruption when pcpu_masks[] is written to again
later in the function.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7375/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 190f1ca85d ("arm64: add support for kernel mode NEON in interrupt
context") introduced a typing error in fpsimd_save_partial_state ENDPROC.
This patch fixes the typing error.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: byungchul.park <byungchul.park@lge.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Our break hooks are used to handle brk exceptions from kgdb (and potentially
kprobes if that code ever resurfaces), so don't bother calling them if
the BRK exception comes from userspace.
This prevents userspace from trapping to a kdb shell on systems where
kgdb is enabled and active.
Cc: <stable@vger.kernel.org>
Reported-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We handle FSCR feature bits (well, TAR only really today) lazily when the guest
starts using them. So when a guest activates the bit and later uses that feature
we enable it for real in hardware.
However, when the guest stops using that bit we don't stop setting it in
hardware. That means we can potentially lose a trap that the guest expects to
happen because it thinks a feature is not active.
This patch adds support to drop TAR when then guest turns it off in FSCR. While
at it it also restricts FSCR access to 64bit systems - 32bit ones don't have it.
Signed-off-by: Alexander Graf <agraf@suse.de>
A VCPU might never stop if it intercepts (for whatever reason) between
"fake interrupt delivery" and execution of the stop function.
Heart of the problem is that SIGP STOP is an interrupt that has to be
processed on every SIE entry until the VCPU finally executes the stop
function.
This problem was made apparent by commit 7dfc63cf97
(KVM: s390: allow only one SIGP STOP (AND STORE STATUS) at a time).
With the old code, the guest could (incorrectly) inject SIGP STOPs
multiple times. The bug of losing a sigp stop exists in KVM before
7dfc63cf97, but it was hidden by Linux guests doing a sigp stop loop.
The new code (rightfully) returns CC=2 and does not queue a new
interrupt.
This patch is a simple fix of the problem. Longterm we are going to
rework that code - e.g. get rid of the action bits and so on.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[some additional patch description]
Since both ARCH_HI3xxx and ARCH_HIX5HD2 are based on Cortex A9 & they're
using similiar kernel features, make them share the hi3xxx_config.
And add it into multi_v7_defconfig too.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
[olof: also turn on ARCH_HISI in multi_v7]
Signed-off-by: Olof Johansson <olof@lixom.net>
Use CPU_METHOD_OF_DECLARE() instead. And declare smp method in dts file.
Changelog:
v6:
* Use hisilicon,hi3620-smp as enable-method property in Hi3620 dts.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rename Hisilicon HI3716 to HIX5HD2 and add dependency on ARCH_HIX5HD2.
HiX5HD2 is a SoC with dual Cortex A9 cores for STB market, and original
Hi3xxx SoC is for mobile market.
To avoid confusing the two types of SoCs and also because of different
implementation (SMP, IPs integrated and earlycon config), rename Hi3716
to HIX5HD2 and add ARCH_HIX5HD2.
Signed-off-by: Haifeng Yan <yanhaifeng@gmail.com>
Signed-off-by: Jiancheng Xue <jchxue@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
[olof: fixed description typos]
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable support for the Hisilicon HiX5HD2 SoC. This HiX5HD2 SoC series
support both single and dual Cortex-A9 cores.
Add ARCH_HIX5HD2 to distinguish HiX5HD2 from Hi3xxx.
They are different in implementation such as SMP, IPs integarted and
earlycon configure.
Signed-off-by: Haifeng Yan <yanhaifeng@gmail.com>
Signed-off-by: Jiancheng Xue <jchxue@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since multiple ARCH configuration will be appended into mach-hisi
directory, add ARCH_HISI as common configuration for different platforms
in mach-hisi.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJT2crRAAoJEPOmecmc0R2B8cAIAIke/dswgq4Kmk/G6spgdict
UXusTcy3mgnzz9X93fl+naGOopCJBSZFkTJFvNNo9nw7V+Knt1R7OW5uXMuOnwZ2
MNMEp9bmZNNKrUNqtrvZeda+Y71TCY8OKLOAnnyfnCToVQ+OCYhW4qkq/G5B3KfI
8YXK8jjhVERUG94+N6AIOxNq0qlmyoc+ZCErjUu6y3BlP/Z7OCLkEhfMmHiwMT7m
CwowMIjE0WhTt4GlVaFhHx5FvBMWI4cQWC61kCJash+U84UY1uGZ/ejPbOcIW0XP
76PCG4wt63sbpeUDjJR52e7HIzP/UGtVdVZACT82YJLpotqB3C5Mc7k/PQw46YM=
=5B5W
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rockchip-rk3288-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Basic rk3288 usb support" from Heiko Stübner:
Add support for rk3288 ehci controllers.
* tag 'v3.17-rockchip-rk3288-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
Signed-off-by: Olof Johansson <olof@lixom.net>
This is the top USB port on the evb (the one closest to the Ethernet
connector).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rk3288 has two kind of usb controller; this adds the ehci variant for
host0 and hsic.
At the moment we don't add any phys for these controllers, but the
default settings seem to work OK.
There is a hardware problem in ohci controller which make it
unavailable and host0 controller can only support high-speed devices.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There is no phy driver that works on the Rockchip board for either USB
host port yet. For now just hardcode the vbus signal to be on all the
time which makes both the dwc2 host and the EHCI port work.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Commit 6a9c001b7e ("MIPS: Switch ELF core dumper to use regsets.")
switched the core dumper to use regsets, however the GP regset code
simply makes a direct copy of the kernel's pt_regs, which does not
match the original core dump register layout as defined in asm/reg.h.
Furthermore, the definition of pt_regs can vary with certain Kconfig
variables, therefore the GP regset can never be relied upon to return
registers in the same layout.
Therefore, this patch changes the GP regset to match the original core
dump layout. The layout differs for 32- and 64-bit processes, so
separate implementations of the get/set functions are added for the
32- and 64-bit regsets.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7452/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Get rid of the WANT_COMPAT_REG_H test and instead define both the 32-
and 64-bit register offset definitions at the same time with
MIPS{32,64}_ prefixes, then define the existing EF_* names to the
correct definitions for the kernel's bitness.
This patch is a prerequisite of the following bug fix patch.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7451/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
task_user_regset_view() should test for TIF_32BIT_REGS in the flags of
the specified task, not of the current task.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7450/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Whenever ptrace attempts to retrieve the FPU implementation register it
accesses it through current_cpu_data, which calls smp_processor_id().
Since the code may execute with preemption enabled, this can trigger
a warning. Fix this by using boot_cpu_data to get the IR instead.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7449/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So far BCM47XX can only detect amount of HIGHMEM. It still requires
adding (registering) and well-testing before enabling by default.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7396/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit d7a887a73d.
Function add_temporary_entry is needed by bcm47xx to support highmem. We
need to add a temporary entry to check for amount of RAM.
The only change made in this revert was replacing (ENTER|EXIT)_CRITICAL.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7395/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It seems that bcm47xx can handle only 128 MiB of RAM directly. There
are few devices with 256 MiB, but Broadcom's SDK uses highmem to handle
anything above 128 MiB.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7101/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Catalin reported that GPIOs used by bcm47xx don't match layout of his
WRT54GS V1.0 board. It seems we need to distinguish these 54G* devices.
Reported-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Working on sound support I noticed the Apalis T30 Evaluation board
device tree missing the more generic Apalis T30 compatible string.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Indentation of the clock property used a hodgepodge of tabs and spaces.
Make them more consistent (tabs for indentation followed by spaces for
alignment).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since this CONFIG option will be used for both Loongson-3A/3B machines,
and not all Loongson-3 machines are produced by Lemote, we rename
CONFIG_LEMOTE_MACH3A to CONFIG_LOONGSON_MACH3X.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7190/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GPIO pin connected to card detect was inverted twice: once by
the argument to the GPIO line itself where it was magically marked
as active low by the flag GPIO_ACTIVE_LOW (0x01) in the third cell,
and also marked active low AGAIN by explicitly stating
"cd-inverted" (a deprecated method).
After commit 78f87df2b4
"mmc: mmci: Use the common mmc DT parser" this results in the
line being inverted twice so it was effectively uninverted, while
the old code would not have this effect, instead disregarding the
flag on the GPIO line altogether, which is a bug. I admit the
semantics may be unclear but inverting twice is as good a
definition as any on how this should work.
So fix up the buggy device tree. Use proper #includes so the DTS
is clear and readable.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Loongson-3 has some specific instructions (MMI/SIMD) in coprocessor 2.
COP2 isn't independent because it share COP1 (FPU)'s registers. This
patch enable the COP2 usage so user-space programs can use the MMI/SIMD
instructions. When COP2 exception happens, we enable both COP1 (FPU)
and COP2, only in this way the fp context can be saved and restored
correctly.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7189/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3B is a 8-cores processor. In general it looks like there are
two Loongson-3A integrated in one chip: 8 cores are separated into two
groups (two NUMA node), each node has its own local memory.
Of course there are some differences between one Loongson-3B and two
Loongson-3A. E.g., the base addresses of IPI registers of each node are
not the same; Loongson-3A use ChipConfig register to enable/disable
clock, but Loongson-3B use FreqControl register instead.
There are two revision of Loongson-3B, the first revision is called as
Loongson-3B1000, whose frequency is 1GHz and has a PRid 0x6306, the
second revision is called as Loongson-3B1500, whose frequency is 1.5GHz
and has a PRid 0x6307. Both revisions has a bug that clock cannot be
disabled at runtime, but this will be fixed in future.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7188/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable sys_mbind()/sys_get_mempolicy()/sys_set_mempolicy() for O32, N32,
and N64 ABIs. By the way, O32/N32 should use the compat version of
sys_migrate_pages()/sys_move_pages(), so fix that.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7186/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Multiple Loongson-3A chips can be interconnected with HT0-bus. This is
a CC-NUMA system that every chip (node) has its own local memory and
cache coherency is maintained by hardware. The 64-bit physical memory
address format is as follows:
0x-0000-YZZZ-ZZZZ-ZZZZ
The high 16 bits should be 0, which means the real physical address
supported by Loongson-3 is 48-bit. The "Y" bits is the base address of
each node, which can be also considered as the node-id. The "Z" bits is
the address offset within a node, which means every node has a 44 bits
address space.
Macros XPHYSADDR and MAX_PHYSMEM_BITS are modified unconditionally,
because many other MIPS CPUs have also extended their address spaces.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7187/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch is prepared for Multi-chip interconnection. Since each chip
has a ChipConfig register, LOONGSON_CHIPCFG should be an array.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7185/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch is prepared for Loongson's NUMA support, it offer meaningful
sysfs files such as physical_package_id, core_id, core_siblings and
thread_siblings in /sys/devices/system/cpu/cpu?/topology.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7184/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On MIPS currently, only the soft limit of cpu count (maxcpus) has its
effect, this patch enable the hard limit (nr_cpus) as well. Processor
cores which greater than maxcpus and less than nr_cpus can be taken up
via cpu hotplug. The code is borrowed from X86.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7183/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Add legacy clocks for SCI for SoCs that do not yet have CCF support.
This is to allow timer devices to be enabled using DT and
will be removed after CCF support is added for each SoC.
This is in keeping with the approach taken for enabling
SCI (serial) devices using DT on these SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8vte
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Third Round of Renesas ARM Based SoC Clock Updates for v3.17" from Simon
Horman:
Third Round of Renesas ARM Based SoC Clock Updates for v3.17
* Add legacy clocks for SCI for SoCs that do not yet have CCF support.
This is to allow timer devices to be enabled using DT and
will be removed after CCF support is added for each SoC.
This is in keeping with the approach taken for enabling
SCI (serial) devices using DT on these SoCs.
* tag 'renesas-clock3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0: add CMT1 clock support for DT
ARM: shmobile: r8a7740: add CMT1 clock support for DT
ARM: shmobile: r8a73a4: add CMT1 clock support for DT
ARM: shmobile: r8a7740: add TMU clock support for DT
ARM: shmobile: r8a7778: add TMU clock support for DT
Signed-off-by: Olof Johansson <olof@lixom.net>
In do_ade(), is_fpu_owner() isn't preempt-safe. For example, when an
unaligned ldc1 is executed, do_cpu() is called and then FPU will be
enabled (and TIF_USEDFPU will be set for the current process). Then,
do_ade() is called because the access is unaligned. If the current
process is preempted at this time, TIF_USEDFPU will be cleard. So when
the process is scheduled again, BUG_ON(!is_fpu_owner()) is triggered.
This small program can trigger this BUG in a preemptible kernel:
int main (int argc, char *argv[])
{
double u64[2];
while (1) {
asm volatile (
".set push \n\t"
".set noreorder \n\t"
"ldc1 $f3, 4(%0) \n\t"
".set pop \n\t"
::"r"(u64):
);
}
return 0;
}
V2: Remove the BUG_ON() unconditionally due to Paul's suggestion.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Jie Chen <chenj@lemote.com>
Signed-off-by: Rui Wang <wangr@lemote.com>
Cc: <stable@vger.kernel.org>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We check that the struct vm_area_struct pointer vma is NULL and then
dereference it a few lines below. The intent was to make sure vma is
not NULL but this is not necessary since the bug pre-dates GIT history
and seem to never have caused a problem. The tlb-4k and tlb-8k versions
of local_flush_tlb_page() don't bother checking if vma is NULL, also
vma is dereferenced before being passed to local_flush_tlb_page(),
thus it is safe to remove this NULL check.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reviewed-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-janitors@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7264/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The dma_cache_wback_inv function performs exactly as is required here,
unless the system has coherent I/O in which case it's a no-op. Call the
underlying cache writeback functions directly, which is arguably clearer
anyway given that the code doesn't actually have anything to do with
DMA in a strict sense.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7282/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When determining the VPE ID of a CPU, make use of the cpu_vpe_id macro
which will return 0 in a non-MT kernel build. Most code is already doing
so but a couple of places weren't. Fixing this prevents a build failure
for non-MT kernels where struct cpuinfo_mips does not contain the vpe_id
field:
arch/mips/kernel/pm-cps.c: In function 'cps_pm_enter_state':
arch/mips/kernel/pm-cps.c:153:51: error: 'struct cpuinfo_mips' has no
member named 'vpe_id'
vpe_cfg = &core_cfg->vpe_config[current_cpu_data.vpe_id];
arch/mips/kernel/smp-cps.c: In function 'wait_for_sibling_halt':
arch/mips/kernel/smp-cps.c:363:33: error: 'struct cpuinfo_mips' has no
member named 'vpe_id'
unsigned vpe_id = cpu_data[cpu].vpe_id;
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When used in a non-MT kernel, the cpu_vpe_id macro never made use of
its cpuinfo argument. It doesn't actually need to since it is returning
a constant 0. However not using the argument can lead to build failures
if the compiler then notices that a variable used as part of the
argument is unused. Prevent that problem by "using" the argument as far
as the compiler is concerned, whilst still returning 0 as before.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7280/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The pm-cps code can run without a CPC, although will be limited to using
only the 2 wait idle states. However the code does check for CPC
presence, and in order to work optimally the CPC support is needed. So
select it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7279/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These symbols will not be defined when CONFIG_MIPS_CPS=n, but although
the CPS_PM_POWER_GATED state will never be used in that case the
compiler doesn't have enough information to figure that out. Add checks
which evaluate to a constant false for CONFIG_MIPS_CPS=n cases in order
to help the compiler out & eliminate the symbol references.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7278/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dynamic tracing of kernel modules is broken on 32-bit MIPS. When modules
are loaded, the kernel crashes when dynamic tracing is enabled with:
cd /sys/kernel/debug/tracing
echo > set_ftrace_filter
echo function > current_tracer
1) arch/mips/kernel/ftrace.c
When the kernel boots, or when a module is initialized, ftrace_make_nop()
modifies every _mcount call site to eliminate the ftrace overhead.
However, when ftrace is later enabled for a call site, ftrace_make_call()
does not currently restore the _mcount call correctly for module call sites.
Added ftrace_modify_code_2r() and modified ftrace_make_call() to fix this.
2) arch/mips/kernel/mcount.S
_mcount assembly routine is supposed to have the caller's _mcount call site
address in register a0. However, a0 is currently not calculated correctly for
module call sites. a0 should be (ra - 20) or (ra - 24), depending on whether
the kernel was built with KBUILD_MCOUNT_RA_ADDRESS or not.
This fix has been tested on Broadcom BMIPS5000 processor. Dynamic tracing
now works for both built-in functions and module functions.
Signed-off-by: Petri Gynther <pgynther@google.com>
Cc: linux-mips@linux-mips.org
Cc: rostedt@goodmis.org
Cc: alcooperx@gmail.com
Cc: cminyard@mvista.com
Patchwork: https://patchwork.linux-mips.org/patch/7476/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The primary dependency is that GHES uses the x86 NMI for hardware
error notification and MCE for memory error handling. These patches
remove that dependency.
Other APEI features such as error reporting via external IRQ, error
serialization, or error injection, do not require changes to use them
on non-x86 architectures.
The following patch set eliminates the APEI Kconfig x86 dependency
by making these changes:
- treat NMI notification as GHES architecture - HAVE_ACPI_APEI_NMI
- group and wrap around #ifdef CONFIG_HAVE_ACPI_APEI_NMI code which
is used only for NMI path
- identify architectural boxes and abstract it accordingly (tlb flush and MCE)
- rework ioremap for both IRQ and NMI context
NMI code is kept in ghes.c file since NMI and IRQ context are tightly coupled.
Note, these patches introduce no functional changes for x86. The NMI notification
feature is hard selected for x86. Architectures that want to use this
feature should also provide NMI code infrastructure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nYdd
-----END PGP SIGNATURE-----
Merge tag 'please-pull-apei' into x86/ras
APEI is currently implemented so that it depends on x86 hardware.
The primary dependency is that GHES uses the x86 NMI for hardware
error notification and MCE for memory error handling. These patches
remove that dependency.
Other APEI features such as error reporting via external IRQ, error
serialization, or error injection, do not require changes to use them
on non-x86 architectures.
The following patch set eliminates the APEI Kconfig x86 dependency
by making these changes:
- treat NMI notification as GHES architecture - HAVE_ACPI_APEI_NMI
- group and wrap around #ifdef CONFIG_HAVE_ACPI_APEI_NMI code which
is used only for NMI path
- identify architectural boxes and abstract it accordingly (tlb flush and MCE)
- rework ioremap for both IRQ and NMI context
NMI code is kept in ghes.c file since NMI and IRQ context are tightly coupled.
Note, these patches introduce no functional changes for x86. The NMI notification
feature is hard selected for x86. Architectures that want to use this
feature should also provide NMI code infrastructure.
If one or more matching FCSR cause & enable bits are set in saved thread
context then when that context is restored the kernel will take an FP
exception. This is of course undesirable and considered an oops, leading
to the kernel writing a backtrace to the console and potentially
rebooting depending upon the configuration. Thus the kernel avoids this
situation by clearing the cause bits of the FCSR register when handling
FP exceptions and after emulating FP instructions.
However the kernel does not prevent userland from setting arbitrary FCSR
cause & enable bits via ptrace, using either the PTRACE_POKEUSR or
PTRACE_SETFPREGS requests. This means userland can trivially cause the
kernel to oops on any system with an FPU. Prevent this from happening
by clearing the cause bits when writing to the saved FCSR context via
ptrace.
This problem appears to exist at least back to the beginning of the git
era in the PTRACE_POKEUSR case.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7438/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used all
devices from the same series are sharing the same mac address. To
prevent mac address collisions we replace them with a mac address based
on the base address. To generate such addresses we take the main mac
address from et0macaddr and increase it by two for the first wifi
device and by 3 for the second one. This matches the printed mac
address on the device. The main mac address increased by one is used as
wan address by the vendor code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7489/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The reboot on the BCM47XX SoCs is done, by setting the watchdog counter
to 1 and let it trigger a reboot, when it reaches 0. Some devices with
a BCM4705/BCM4785 SoC do not reboot when the counter is set to 1 and
decreased to 0 by the hardware. It looks like it works more reliable
when we set it to 3. As far as I understand the hardware, this should
not make any difference, but I do not have access to any documentation
for this SoC.
It is still not 100% reliable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7488/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Exynos has buggy firmware that puts bad data into the memory node. Commit
1c2f87c2 (ARM: Get rid of meminfo) exposed the bug by dropping the artificial
upper bound on the number of memory banks that can be added. Exynos fails to
boot after that commit. This branch fixes it by splitting the early DT parse
function and inserting a fixup hook. Exynos uses the hook to correct the DT
before parsing memory regions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lmyQ
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull Exynos platform DT fix from Grant Likely:
"Device tree Exynos bug fix for v3.16-rc7
This bug fix has been brewing for a while. I hate sending it to you
so late, but I only got confirmation that it solves the problem this
past weekend. The diff looks big for a bug fix, but the majority of
it is only executed in the Exynos quirk case. Unfortunately it
required splitting early_init_dt_scan() in two and adding quirk
handling in the middle of it on ARM.
Exynos has buggy firmware that puts bad data into the memory node.
Commit 1c2f87c225 ("ARM: Get rid of meminfo") exposed the bug by
dropping the artificial upper bound on the number of memory banks that
can be added. Exynos fails to boot after that commit. This branch
fixes it by splitting the early DT parse function and inserting a
fixup hook. Exynos uses the hook to correct the DT before parsing
memory regions"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
arm: Add devicetree fixup machine function
of: Add memory limiting function for flattened devicetrees
of: Split early_init_dt_scan into two parts
often during boot with Ubuntu 14.04 PV guests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJT2PhgAAoJEFxbo/MsZsTRlzIH/1HjbkGZmRlOj5wcrYlWCUJ/
DGLBHc76so52xd9oP8COT5tuSVP6/usPPLFaOmVZ7fMiOpoyz9d3lc0g56otw3gJ
tTUFTyW0EoFtvmIl50OMC726p9azETjA3P2XJkV/D3GhBGGqgrP5uR+mRvisvq3y
eGZEx1UIHv1jov47TBFR1NcckXBWw+6J9m34y9h6an9VNDCuuGwYZ8dfGAFsLrVb
lGLTmgQQmyk4SexVINfOwL40KkVDVEq+X74HcPviyNHEIy66xLzMtKpL+Sf4xeuv
VG3JhqAUGuRGGK48rrbpxhBbpxGp35O9RV68YrGssxfuTejSYduw5zTzzt30QIA=
=cr8X
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.16-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fix from David Vrabel:
"Fix BUG when trying to expand the grant table. This seems to occur
often during boot with Ubuntu 14.04 PV guests"
* tag 'stable/for-linus-3.16-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: safely map and unmap grant frames when in atomic context
Matching x86 and making it more convenient to run the arm64 default
kernel as distros like Ubuntu need this option.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Remove a prototype which was added by both 93c4adc7af and 36be0b9deb.
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Building a kernel with CPU_BIG_ENDIAN fails if there are stale objects
from a !CPU_BIG_ENDIAN build. Due to a missing FORCE prerequisite on an
if_changed rule in the VDSO Makefile, we attempt to link a stale LE
object into the new BE kernel.
According to Documentation/kbuild/makefiles.txt, FORCE is required for
if_changed rules and forgetting it is a common mistake, so fix it by
'Forcing' the build of vdso. This patch fixes build errors like these:
arch/arm64/kernel/vdso/note.o: compiled for a little endian system and target is big endian
failed to merge target specific data of file arch/arm64/kernel/vdso/note.o
arch/arm64/kernel/vdso/sigreturn.o: compiled for a little endian system and target is big endian
failed to merge target specific data of file arch/arm64/kernel/vdso/sigreturn.o
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This pci fixup routine calls __init functions.
In general pci fixup routine must not call __init functions,
but this pci/isa bridge device is not hotpluggable anyway.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7215/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes a regression caused by commit
bb6c0bd3fd [MIPS: SB1: Fix excessive kernel
warnings.], that makes `-march=r5000' selected for compilation flags
rather than supposed `-march=sb1' with compilers that do not support the
ASE selection flags introduced with that change.
For example GCC 4.1.2 supports `-mips3d'/`-mno-mips3d' (and obviously
`-march=sb1'), however it does not support `-mdmx'/`-mno-mdmx'. As a
result the whole selection of flags fails and compilation resorts to using
`-march=r5000', meant for really old compilers indeed only.
It is always best to pick the flags individually unless we are absolutely
sure a set of flags was introduced to the toolchain together (`-march=sb1'
and `-mtune=sb1' would be a good example), and this change makes it happen
for CONFIG_CPU_SB1. Consequently the flags ultimately selected with GCC
4.1.2 are `-march=sb1 -Wa,--trap -mno-mips3d'
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Richard Sandiford <rdsandiford@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7223/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes:
{standard input}: Assembler messages:
{standard input}:145: Error: opcode not supported on this processor: vr5000 (mips4) `clz $2,$2'
{standard input}:920: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$9'
{standard input}:1797: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:1851: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:2831: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:4209: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:4329: Error: opcode not supported on this processor: vr5000 (mips4) `clz $2,$2'
make[2]: *** [arch/mips/mm/tlbex.o] Error 1
which triggered due to a regression causing the file to be built with
`-march=r5000' rather than `-march=sb1', fixed separately. Nevertheless
the error should not happen, the other uses of CLZ are appropriately
guarded. This change copies the arrangement from one of those other
places.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Code in a switch statement in probe_pcache checks the CPU type twice
unnecessarily for processor implementations that have the alias removal
feature reported by the CP0 Config7.AR and Config7.IAR bits. This change
rewrites the affected fragment avoiding the extraneous check and improving
readability.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7221/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Wire up the set_affinity call for the internal PIC if booting on
a cpu supporting it.
Affinity is kept to boot cpu as default.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for applying affinity, use the irq descriptor as the
argument for (un)mask.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7317/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 7dfc63cf97
(KVM: s390: allow only one SIGP STOP (AND STORE STATUS) at a time)
introduced a memory leak if a sigp stop is already pending. Free
the allocated inti structure.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Since we will have the chance of accessing the registers concurrently,
protect any accesses through a spinlock.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Set it to zero if there is no second set.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SMP capable irq controllers have two interrupt output pins which are
controlled through separate registers, so make the variables arrays.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7318/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic version uses a variable length of u32 registers instead of u32/u64.
This allows easier support for "wider" registers without having to rewrite
everything.
This "generic" version is as fast as the old version in the best case
(i == next set bit), and twice as fast in the worst case in 64 bits.
Using a macro was chosen over a (forced) inline version because gcc generated
more compact code with the macro.
The change from (signed) int to unsigned int for i and to_call was intentional
as the value can be only between 0 and (width - 1) anyway, and allowed gcc to
optimise the code a bit further.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7316/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allows up to drop the prototypes from the top.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7315/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make it follow the same naming convention as the other functions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7314/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that we have properly split load/store instruction emulation and generic
instruction emulation, we can move the generic one from kvm.ko to kvm-pr.ko
on book3s_64.
This reduces the attack surface and amount of code loaded on HV KVM kernels.
Signed-off-by: Alexander Graf <agraf@suse.de>
Use the same pattern as with get_*_cpu_type() to allow the compiler
to remove code for non enabled SoC types.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7273/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All three SoCs have in common they have a BMIPS32/BMIPS3300 CPU, so
we can replace this as no SoC with BMIPS4350 support enabled.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7272/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch_gnttab_map_frames() and arch_gnttab_unmap_frames() are called in
atomic context but were calling alloc_vm_area() which might sleep.
Also, if a driver attempts to allocate a grant ref from an interrupt
and the table needs expanding, then the CPU may already by in lazy MMU
mode and apply_to_page_range() will BUG when it tries to re-enable
lazy MMU mode.
These two functions are only used in PV guests.
Introduce arch_gnttab_init() to allocates the virtual address space in
advance.
Avoid the use of apply_to_page_range() by using saving and using the
array of PTE addresses from the alloc_vm_area() call (which ensures
that the required page tables are pre-allocated).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We are using the mips counters as the clock source, so we need to ensure
they are synced, else e.g. gettimeofday will return different values
depending on which core it was run.
Observed difference was about 8 seconds, causing ~8 seconds ping or time
running backwards for some programs.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7265/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In commit 2c8c53e28f (MIPS: Optimize TLB handlers for Octeon CPUs)
build_r4000_tlb_refill_handler() is modified. But it doesn't compatible
with the original code in HUGETLB case. Because there is a copy & paste
error and one line of code is missing. It is very easy to produce a bug
with LTP's hugemmap05 test.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Binbin Zhou <zhoubb@lemote.com>
Cc: <stable@vger.kernel.org>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7496/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the clock framework in place, remove unused functions and bits,
and drop the CLK_IGNORE_UNUSED flag, which is now unneeded.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7473/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the clock framework to en/disable the clock to the au1100
framebuffer device.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7474/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the clk framework to set up and enable all PSC clocks.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7469/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the clock framework to get at the PCI clock source and enable
it on driver initialization.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7471/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add use of the common clock framework to set and enable the 48MHz
clock source for the onchip OHCI and UDC blocks.
Tested on a DB1500. (Au1200 and Au1300 use an external 48MHz crystal).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7467/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the clock framework to get the rate of the peripheral clock.
Remove the now obsolete get_uart_baud_base function.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7468/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces common clock framework integration for all
configurable on-chip clocks on Alchemy chips:
- 2 or 3 PLLs which generate integer multiples of the root rate 12MHz,
- 6 dividers which take one of the 3 PLLs as input and divide their
rate by either multiples of 2 or 1 (Au1300).
- another bank of up to 6 muxes which take either one of the 6
above dividers or one of the PLLs directly and divide their rate
further by 1, 2, 3 or 4.
- a few other sources which are used by onchip peripherals and are
informational.
This implementation will take the clock tree as it was set up
by boot firmware: all in-kernel boards should continue to work
without having to set up the clock tree in board code.
CLK_IGNORE_DISABLED will be removed once all drivers have been
converted.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7466/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes the static memory controller registers to offsets
from base, prefixes them with AU1000_ to avoid silent failures due to
changed addresses and introduces helpers to access them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7463/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes all absolute SYS_XY registers to offsets from the
SYS block base, prefixes them with AU1000 to avoid silent failures due
to changed addresses, and introduces helper functions to read/write
them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7464/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the C-code after all macros: A follow-on patch which
introduces helpers to access the SYS_* registers needs this to build.
Just code shuffling, no functional changes.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the register offsets and bit descriptions from the au1000.h header
to their only user, the au1000_eth.c driver.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: netdev@vger.kernel.org
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Runtime tested on Mikrotik RB532 board.
Thanks goes to Geert Uytterhoeven for the explanation of the problem.
"I'm afraid this is not gonna help. When the port is unregistered,
its type will be reset to PORT_UNKNOWN.
So before registering it again, its type must be set again the actual
serial driver, cfr. the change to of_serial.c."
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Cc: geert@linux-m68k.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7241/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is required so that we give up the last reference to the device.
Also, create a gio_bus_release() that calls kfree on the device argument to
properly kfree() the memory allocated for the device.
[ralf@linux-mips.org: Reformat to Linux coding style and make
gio_bus_release static.]
Signed-off-by: Levente Kurusa <levex@linux.com>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is required so that we give up the last reference to the device.
Also, add a new tx_7segled_release function which will be called after the
put_device to ensure that device is kfree'd.
[ralf@linux-mips.org: Reformat to Linux coding style and make
tx_7segled_release static.]
Signed-off-by: Levente Kurusa <levex@linux.com>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6260/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is required so that we give up the last reference to the device.
Also, rework error path so that it is easier to read.
[ralf@linux-mips.org: Reformat to Linux coding style and make
txx9_device_release static; folded in build fix by Levente for the
original patch.]
Signed-off-by: Levente Kurusa <levex@linux.com>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6259/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This are not specific to e500hv but applicable for bookehv
(As per comment from Scott Wood on my patch
"kvm: ppc: bookehv: Added wrapper macros for shadow registers")
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
In commit 4a0e637738 ("clocksource: Get rid of cycle_last"),
currently in the -tip tree, there was a small typo where cycles_t
was used intstead of cycle_t. This broke ppc64 builds.
Fix this by using the proper cycle_t type for this usage, in
both the definition and the ia64 implementation.
Now, having both cycle_t and cycles_t types seems like a very
bad idea just asking for these sorts of issues. But that
will be a cleanup for another day.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1406349439-11785-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 1c2f87c225
(ARM: 8025/1: Get rid of meminfo) dropped the upper bound on
the number of memory banks that can be added as there was no
technical need in the kernel. It turns out though, some bootloaders
(specifically the arndale-octa exynos boards) may pass invalid memory
information and rely on the kernel to not parse this data. This is a
bug in the bootloader but we still need to work around this.
Work around this by introducing a dt_fixup function. This function
gets called before the flattened devicetree is scanned for memory
and the like. In this fixup function for exynos, limit the maximum
number of memory regions in the devicetree.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Andreas Färber <afaerber@suse.de>
[glikely: Added a comment and fixed up function name]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
In commit ae91d60ba8, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
mpic_msgrs has type struct mpic_msgr **, not struct mpic_msgr *, so the
elements of the array should have pointer type, not structure type.
The advantage of kcalloc is, that will prevent integer overflows which
could result from the multiplication of number of elements and size and
it is also a bit nicer to read.
The Coccinelle semantic patch that makes the first change is as follows:
// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@
x =
<+...sizeof(
- T
+ *x
)...+>
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The CoreNet Coherency Fabric is part of the memory subsystem on
some Freescale QorIQ chips. It can report coherency violations (e.g.
due to misusing memory that is mapped noncoherent) as well as
transactions that do not hit any local access window, or which hit a
local access window with an invalid target ID.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Erratum A-008139 can cause duplicate TLB entries if an indirect
entry is overwritten using tlbwe while the other thread is using it to
do a lookup. Work around this by using tlbilx to invalidate prior
to overwriting.
To avoid the need to save another register to hold MAS1 during the
workaround code, TID clearing has been moved from tlb_miss_kernel_e6500
until after the SMT section.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The general idea is that each core will release all of its
threads into the secondary thread startup code, which will
eventually wait in the secondary core holding area, for the
appropriate bit in the PACA to be set. The kick_cpu function
pointer will set that bit in the PACA, and thus "release"
the core/thread to boot. We also need to do a few things that
U-Boot normally does for CPUs (like enable branch prediction).
Signed-off-by: Andy Fleming <afleming@freescale.com>
[scottwood@freescale.com: various changes, including only enabling
threads if Linux wants to kick them]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This ensures that all MSR definitions are consistently unsigned long,
and that MSR_CM does not become 0xffffffff80000000 (this is usually
harmless because MSR is 32-bit on booke and is mainly noticeable when
debugging, but still I'd rather avoid it).
Signed-off-by: Scott Wood <scottwood@freescale.com>
The nasid_to_try variable is an array of integers, so plain integers can
be used when assigning values to the elements rather than casting a NULL
pointer to an integer, which results in the following warning from GCC:
arch/ia64/sn/kernel/bte.c:117:22: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
nasid_to_try[1] = (int)NULL;
^
arch/ia64/sn/kernel/bte.c:125:22: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
nasid_to_try[1] = (int)NULL;
^
Replace (int)NULL with a simple 0 to silence these warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The code uses a the following to zero out a PDA:
memset(pda, 0, sizeof(pda));
But sizeof(pda) will return the size of a pointer rather than the size
of the structure pointed to. This triggers the following warning from
GCC:
arch/ia64/sn/kernel/setup.c:582:23: warning: argument to 'sizeof' in 'memset' call is the same pointer type 'struct pda_s *' as the destination; expected 'struct pda_s' or an explicit length [-Wsizeof-pointer-memaccess]
memset(pda, 0, sizeof(pda));
^
Fix this by passing in the size of the structure using sizeof(*pda)
instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch add missing pinctrl for uart0/1 for Exynos3250. The gpio pin (
uart0_data, uart0_fctl, uart1_data) is only used for UART IP.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes duplicat 'interrupt-parent' property for Exynos3250
because exynos3250.dtsi already defined 'interrupt-parent' property
as following:
In arch/arm/boot/dts/exynos3250.dtsi:
compatible = "samsung,exynos3250";
interrupt-parent = <&gic>;
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add TMU (Thermal Management Unit) dt node to monitor the high
temperature for Exynos3250.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The IRQB interrupt pin of MAX77686 PMIC is connected to GPX3[2] pin of
Exynos5250 on the Exynos5250 SMDK board. Specify this connection using
interrupts property for the max77686 pmic node.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an Atmel maXTouch instead.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an s5m8767 instead.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The platforms selecting NEED_MACH_MEMORY_H defined the start address of
their physical memory in the respective <mach/memory.h>. With
ARM_PATCH_PHYS_VIRT=y (which is quite common today) this is useless
though because the definition isn't used but determined dynamically.
So remove the definitions from all <mach/memory.h> and provide the
Kconfig symbol PHYS_OFFSET with the respective defaults in case
ARM_PATCH_PHYS_VIRT isn't enabled.
This allows to drop the dependency of PHYS_OFFSET on !NEED_MACH_MEMORY_H
which prevents compiling an integrator nommu-kernel.
(CONFIG_PAGE_OFFSET which has "default PHYS_OFFSET if !MMU" expanded to
"0x" because CONFIG_PHYS_OFFSET doesn't exist as INTEGRATOR selects
NEED_MACH_MEMORY_H.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A nice small set of bug fixes for arm-soc:
- two incorrect register addresses in DT files on shmobile and hisilicon
- one revert for a regression on omap
- one bug fix for a newly introduced pin controller binding
- one regression fix for the memory controller on omap
- one patch to avoid a harmless WARN_ON
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Ny58
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A nice small set of bug fixes for arm-soc:
- two incorrect register addresses in DT files on shmobile and hisilicon
- one revert for a regression on omap
- one bug fix for a newly introduced pin controller binding
- one regression fix for the memory controller on omap
- one patch to avoid a harmless WARN_ON"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: Revert enabling of twl configuration for n900
ARM: dts: fix L2 address in Hi3620
ARM: OMAP2+: gpmc: fix gpmc_hwecc_bch_capable()
pinctrl: dra: dt-bindings: Fix pull enable/disable
ARM: shmobile: r8a7791: Fix SD2CKCR register address
ARM: OMAP2+: l2c: squelch warning dump on power control setting
broken legacy code for omap1 and move things towards
device tree.
These patches were posted a while back, but I did not
realize I was supposed to merge the driver related
parts too. So apologies for a late pull request on
these changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZyPG
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.17/mailbox-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Merge "late omap mailbox clean-up, driver parts" from Tony Lindgren:
Driver specific omap mailbox cleanup. Mostly to remove
broken legacy code for omap1 and move things towards
device tree.
These patches were posted a while back, but I did not
realize I was supposed to merge the driver related
parts too. So apologies for a late pull request on
these changes.
* tag 'omap-for-v3.17/mailbox-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When running as a kvm guest on a para-virtualised platform, it is useful
to have virtio implementations of console, 9pfs and network.
This adds these options to the arm64 defconfig, so we can easily run a
defconfig kernel build as both host and as a kvm guest.
Signed-off-by: Will Deacon <will.deacon@arm.com>
On LPAE, each level 1 (pgd) page table entry maps 1GiB, and the level 2
(pmd) entries map 2MiB.
When the identity mapping is created on LPAE, the pgd pointers are copied
from the swapper_pg_dir. If we find that we need to modify the contents
of a pmd, we allocate a new empty pmd table and insert it into the
appropriate 1GB slot, before then filling it with the identity mapping.
However, if the 1GB slot covers the kernel lowmem mappings, we obliterate
those mappings.
When replacing a PMD, first copy the old PMD contents to the new PMD, so
that we preserve the existing mappings, particularly the mappings of the
kernel itself.
[rewrote commit message and added code comment -- rmk]
Fixes: ae2de10173 ("ARM: LPAE: Add identity mapping support for the 3-level page table format")
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5XAH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap n900 regression fix for v3.16 rc series" from Tony Lindgren:
Minimal regression fix for n900 display that got broken with
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
* tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert enabling of twl configuration for n900
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
or the next one below it. This is intended to resolve some DSS problems.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/clock-b-v3.17/20140725061121/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fXvM
-----END PGP SIGNATURE-----
Merge tag 'for-v3.17/omap-clock-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.17/soc
Modify OMAP PLL rate rounding function to round to the exact rate requested
or the next one below it. This is intended to resolve some DSS problems.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/clock-b-v3.17/20140725061121/
If init_mm.brk is not section aligned, the LPAE fixup code will miss
updating the final PMD. Fix this by aligning map_end.
Fixes: a77e0c7b27 ("ARM: mm: Recreate kernel mappings in early_paging_init()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The fields are not used by the driver and will be removed from platform
data. Don't set them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There are no existing users for OMAP1 mailbox driver
in kernel. Commit ab6f775 "Removing dead OMAP_DSP"
has cleaned up all the dead code related to the only
possible user, including the creation of the mailbox
platform device.
Remove this stale driver so that the OMAP mailbox
driver can be simplified and streamlined better for
converting to mailbox framework.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration
for selected omaps) allowed n900 to cut off core voltages during
off-idle. This however caused a regression where twl regulator
vaux1 was not getting enabled for the LCD panel as we are not
requesting it for the panel.
Turns out quite a few devices on n900 are using vaux1, and we need
to either stop idling it, or add proper regulator_get calls for all
users. But until we have a proper solution implemented and tested,
let's just disable the twl off-idle configuration for now for n900.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration for selected omaps)
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DMA engine is enabled for all DTs that derive from zynq-7000.dtsi.
There is no need to override the 'status' property in board DTs.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This moves the espfix64 logic into native_iret. To make this work,
it gets rid of the native patch for INTERRUPT_RETURN:
INTERRUPT_RETURN on native kernels is now 'jmp native_iret'.
This changes the 16-bit SS behavior on Xen from OOPSing to leaking
some bits of the Xen hypervisor's RSP (I think).
[ hpa: this is a nonzero cost on native, but probably not enough to
measure. Xen needs to fix this in their own code, probably doing
something equivalent to espfix64. ]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/7b8f1d8ef6597cb16ae004a43c56980a7de3cf94.1406129132.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
Exynos initialisation code now relies on obtaining the PMU address via
DT, so add the exynos5260 PMU compatible string to DT match table.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos initialization code now relies on obtaining the PMU address,
so add the new 5410 value to the list of compatible string matches.
This unbreaks booting on 5410 based boards.
Fixes: fce9e5bb25 ("ARM: EXYNOS: Add support for mapping PMU base
address via DT")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos initialization code now relies on obtaining the PMU address,
so prepare a PMU node for Exynos5410.
Fixes: fce9e5bb25 ("ARM: EXYNOS: Add support for mapping PMU base
address via DT")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull ARM AES crypto fixes from Herbert Xu:
"This push fixes a regression on ARM where odd-sized blocks supplied to
AES may cause crashes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm-aes - fix encryption of unaligned data
crypto: arm64-aes - fix encryption of unaligned data
Pull powerpc fixes from Ben Herrenschmidt:
"Here are 3 more small powerpc fixes that should still go into .16.
One is a recent regression (MMCR2 business), the other is a trivial
endian fix without which FW updates won't work on LE in IBM machines,
and the 3rd one turns a BUG_ON into a WARN_ON which is definitely a
LOT more friendly especially when the whole thing is about retrieving
error logs ..."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix endianness of flash_block_list in rtas_flash
powerpc/powernv: Change BUG_ON to WARN_ON in elog code
powerpc/perf: Fix MMCR2 handling for EBB
DCR handling was only needed for 440 KVM. Since we removed it, we can also
remove handling of DCR accesses.
Signed-off-by: Alexander Graf <agraf@suse.de>
Update the bindings for touchscreen size.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Update the bindings for touchscreen size.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We're going to implement guest code interpretation in KVM for some rare
corner cases. This code needs to be able to inject data and instruction
faults into the guest when it encounters them.
Expose generic APIs to do this in a reasonably subarch agnostic fashion.
Signed-off-by: Alexander Graf <agraf@suse.de>
Today the instruction emulator can get called via 2 separate code paths. It
can either be called by MMIO emulation detection code or by privileged
instruction traps.
This is bad, as both code paths prepare the environment differently. For MMIO
emulation we already know the virtual address we faulted on, so instructions
there don't have to actually fetch that information.
Split out the two separate use cases into separate files.
Signed-off-by: Alexander Graf <agraf@suse.de>
- BCM Mobile SMP support
- BRCM STB platform support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lUq9
-----END PGP SIGNATURE-----
Merge tag 'for-3.17/bcm-soc' of git://github.com/broadcom/mach-bcm into next/soc
Merge "ARM: mach-bcm: soc updates for 3.17" from Matt Porter:
- BCM Mobile SMP support
- BRCM STB platform support
* tag 'for-3.17/bcm-soc' of git://github.com/broadcom/mach-bcm:
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- BCM Mobile SMP support
- BRCM STB platform support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZOoN
-----END PGP SIGNATURE-----
Merge tag 'for-3.17/bcm-dt' of git://github.com/broadcom/mach-bcm into next/dt
Merge "ARM: mach-bcm: dt updatees for 3.17" from Matt Porter:
- BCM Mobile SMP support
- BRCM STB platform support
* tag 'for-3.17/bcm-dt' of git://github.com/broadcom/mach-bcm:
ARM: brcmstb: dts: add a reference DTS for Broadcom 7445
ARM: brcmstb: gic: add compatible string for Broadcom Brahma15
ARM: brcmstb: add misc. DT bindings for brcmstb
ARM: brcmstb: add CPU binding for Broadcom Brahma15
ARM: dts: enable SMP support for bcm21664
ARM: dts: enable SMP support for bcm28155
devicetree: bindings: document Broadcom CPU enable method
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTzJFGAAoJEHm+PkMAQRiGNzQH/087gQch5K+A2HKvPzjUXq57
G82DJHLONMMq8+NY3Vqhp8g2V8zRbXGJEvMJMsyuscO37Vo7ADcrYo8lqY9w5bIl
h+Zarhkqz0rqRs2SfMMIVzdd2W7MzL+lqj3GplGPxHztw0+qk7PRKILx6eRppGaH
JaD4NfkD5+1vfve/2d1ze9D5pCiw6PFNzjesKZxScQhNhIyLdRamfSTY4r9XeURo
CxpwjphEYfvAcgc39mwzEHPHyKSqULu0By6R8FXQpJ9QjVtzcGEiF+cPqGncpZOR
5ZSyU5e1CpBl9w8o6Lm9ewXmaCSnBU/VFrOwWvZrXfokZedXBOz7KdShU93XFjU=
=0VJM
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc6' into next/dt
Update to Linux 3.16-rc6 as a dependency for the broadcom changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Armada XP
- New board, Lenovo ix4-300d NAS
- Add Lenovo to vendor-prefixes
- Dove
- Add LCD controllers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ixkt
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.17-4' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu DT changes for v3.17 (round 4)" from Jason Cooper"
- Armada XP
- New board, Lenovo ix4-300d NAS
- Add Lenovo to vendor-prefixes
- Dove
- Add LCD controllers
* tag 'mvebu-dt-3.17-4' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Add dts definition for Lenovo Iomega ix4-300d NAS
of: Add Lenovo Group Ltd. to the vendor-prefixes list.
ARM: dts: dove: add DT LCD controllers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We use kvmppc_ld and kvmppc_st to emulate load/store instructions that may as
well access the magic page. Special case it out so that we can properly access
it.
Signed-off-by: Alexander Graf <agraf@suse.de>
We have a nice and handy helper to read from guest physical address space,
so we should make use of it in kvmppc_ld as we already do for its counterpart
in kvmppc_st.
Signed-off-by: Alexander Graf <agraf@suse.de>
We have enough common infrastructure now to resolve GVA->GPA mappings at
runtime. With this we can move our book3s specific helpers to load / store
in guest virtual address space to common code as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
We have a nice API to find the translated GPAs of a GVA including protection
flags. So far we only use it on Book3S, but there's no reason the same shouldn't
be used on BookE as well.
Implement a kvmppc_xlate() version for BookE and clean it up to make it more
readable in general.
Signed-off-by: Alexander Graf <agraf@suse.de>
Linus Torvalds