Upon a failure we never call ath9k_ps_restore() on ath_radio_enable(),
this will throw off the sc->ps_usecount. When the sc->ps_usecount
is > 0 we never put the chip to full sleep. This drains battery,
and will also make the chip fail upon resume with:
ath: Starting driver with initial channel: 5745 MHz
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
This would make the chip useless upon resume.
I cannot prove this can happen but in theory it is so best to
avoid this race completely and not have users complain about
a broken device after resume.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On suspend, there might be usb wireless drivers which wrongly trigger
the warning in ieee80211_work_work. If an usb driver doesn't have a
suspend hook, the usb stack will disconnect the device. On disconnect,
a mac80211 driver calls ieee80211_unregister_hw, which calls dev_close,
which calls ieee80211_stop, and in the end calls ieee80211_work_purge->
ieee80211_work_work.
The problem is that this call to ieee80211_work_purge comes after
mac80211 is suspended, triggering the warning even when we don't have
work queued in work_list (the expected case when already suspended),
because it always calls ieee80211_work_work.
So, just call ieee80211_work_work in ieee80211_work_purge if we really
have to abort work. This addresses the warning reported at
https://bugzilla.kernel.org/show_bug.cgi?id=24402
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dev_open will eventually call ieee80211_ibss_join which sets up the
skb used for beacons/probe-responses however it is possible to
receive beacons that attempt to merge before this occurs causing
a null pointer dereference. Check ssid_len as that is the last
thing set in ieee80211_ibss_join.
This occurs quite easily in the presence of adhoc nodes with hidden SSID's
revised previous patch to check further up based on irc feedback
Signed-off-by: Tim Harvey <harvey.tim@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code wants to check if there's a channel and it is not disabled,
but it used to check if channel is not NULL and accessed the channel
struct if this check failed.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From: Johannes Berg <johannes.berg@intel.com>
The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.
However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Description by Hauke:
"If CONFIG_ATH_DEBUG=y is set ATH_DBG_WARN_ON_ONCE uses WARN_ON_ONCE and
returns something, but if CONFIG_ATH_DEBUG is not set it does not return
anything. Now ATH_DBG_WARN_ON_ONCE is used in the boolean expression in
an if case and is not returning anything and causes a compile error.
CC [M] /drivers/net/wireless/ath/ath9k/main.o
/drivers/net/wireless/ath/ath9k/main.c: In function ‘ath_isr’:
/drivers/net/wireless/ath/ath9k/main.c:769: error: expected expression
before ‘do’
make[5]: *** [/drivers/net/wireless/ath/ath9k/main.o] Error 1
make[4]: *** [/drivers/net/wireless/ath/ath9k] Error 2"
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AHB bus support patchset moved the table "Known PCI ids" from base.c
to pci.c - unfortunately, MODULE_DEVICE_TABLE() was not transferred.
With this fix 'modinfo ath5k' lists the alias -> pci-id lines, again.
The issue was introduced by:
commit e5b046d86f
"ath5k: Move PCI bus functions to separate file."
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Suspend requires the device to be in fullsleep otherwise upon
resume the device becomes unresponsive. We need to ensure
that when we want the device to go to sleep it yields to
the request, otherwise we'll have a useless devices upon
resume. Warn when changing the power fails as we need
to look into these issues.
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not be idle when we get the ATH9K_INT_TIM_TIMER,
otherwise its a sign of something broken in our design with
our idle state machine and mac80211. Skip these and WARN once
just in case this is triggerable.
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This let us avoid double addressing while still having reg check.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Order was changed in specs. For writing arrays we have designed bulk function
which makes use of auto increment and do not write table address over and over.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It can be NULL according to docs, and logging showed it
to be NULL in practice.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new BSS attribute to allow hostapd to set the current HT opmode.
Otherwise drivers won't be able to set up protection for HT rates in
AP mode.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.
This bug causes the response of the system to certain attacks to be
ineffective.
It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.
wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.
The log tends to look like:
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... and interface up.
In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.
Clear the setting so that the reporting matches what the driver has
done..
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be set to FULLSLEEP mode during suspend,
when no interface has been brought up. Not doing this would
break resume, as the chip won't be powered up at all.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This results in an erroneus num_adhoc_vifs count, as the this counter
was incremented but not decremented for mesh interfaces.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt handler takes a lock - but since commit bcad6e80f3 this
lock goes through an indirection specified in the hermes_t structure.
We must therefore initialise the structure before setting up the
interrupt handler.
Fix orinoco_cs and spectrum_cs
<https://bugzilla.kernel.org/show_bug.cgi?id=23932>
Bisected by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we fail to find a hci device pointer in hci_uart, don't try
to deref the NULL one we do have.
Signed-off-by: Jun Nie <njun@marvell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In order to send data to management control sockets the function should:
- skip checks intended for raw HCI data and stack internal events
- make sure RAW HCI data or stack internal events don't go to
management control sockets
In order to accomplish this the patch adds a new member to the bluetooth
skb private data to flag skb's that are destined for management control
sockets.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add initial definitions for the new Bluetooth Management interface to
the bluetooth headers.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Wrap mesh sections inside CONFIG_MAC80211_MESH to fix compilation
problems reported by Stephen Rothwell, Larry Finger and Bruno Randolf.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The structure struct ieee80211_rx_status *rxs is no longer needed to be
passed to ath_rx_send_to_mac80211 function
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the current save power save implementation we assume a dtim period
of 1.This value is assigned based on a sanity check in the driver
eventhough we had not parsed it from mac80211.This patch obtains the actual
DTIM period from AP by parsing it from mac80211.Yet for handling
multicast traffic we may still have it as fixed rather than parsing it
from mac80211 .This does not breaks power save or anything as the sleep
duration is currently fixed in the driver.This patch may serve to improve
power save in the future by using dtim period for sleep duration and using
correct dtim period adhoc mode.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AUTOSLEEP feature is enabled only for AR9271 and AR9003 version
chipsets.So unlikely macro should be used only to check whether
auto-sleep feature is enabled
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath.ko is a common module shared between ath5k, ar9170usb, ath9k and ath9k_htc.
Adding driver specific data to the shared structure would impact all the
drivers. Handling USB device recognition for devices specific to ath9k_htc
can be handled within the driver itself.
Also, AR7010 refers to the processor used in both AR9280/AR9287 based
devices. Rename the device enumerations accordingly.
While at it, check properly for the bus type when choosing the EEPROM
base address for UB95.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/mlme.c: In function 'ieee80211_sta_work':
net/mac80211/mlme.c:1981: warning: too many arguments for format
Introduced by commit 04ac3c0ee2
("mac80211: speed up AP probing using nullfunc frames").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One thing I missed in my WME series: Older hardware does not have enough
hardware queues to support WME. In this case we just set up one data queue. Use
the capability information to decide how many queues to set up.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This decreases spammage in the log. A single line message
will still be printed, so users can be aware that problem
exists.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez