Hdmi driver may not receive intrinsic event from gfx side when
it's in runtime suspend mode. There's no ELD info when exit from
runtime suspend. This patch avoid missing ELD info.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Intel Haswell HDMI codecs, the pins choose converter 0 by default.
This would cause conflict when playing audio on unused pins,the pin with
physical device connected would get audio data too.
i.e. Pin 0/1/2 default choose converter 0, pin 1 has HDMI monitor connected.
when play audio on Pin 0 or pin 2, pin 1 could get audio data too.
This patch configure unused pins to choose different converter.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a selection to a converter MUX is changed in hdmi_pcm_open(), it
should be cached so that the given connection can be restored properly
at PM resume. We need just to replace the corresponding
snd_hda_codec_write() call with snd_hda_codec_write_cache().
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell converters maybe in wrong power state before usage.
i.e. only converter 0 is in D0, converter 1/2 are in D3.
When pin choose converter 1/2, there's no audio output, this
cause dependency when playing differnt stream on pins.
AUD_PWRST ConvertorA_Widget_Power_State_Current D0
AUD_PWRST ConvertorA_Widget_Power_State_Requsted D0
AUD_PWRST ConvertorB_Widget_Power_State_Current D3
AUD_PWRST ConvertorB_Widget_Power_State_Requested D3
AUD_PWRST ConvC_Widget_PwrSt_Curr D3
AUD_PWRST ConvC_Widget_PwrSt_Req D3
This patch check converter's power state and set D0 if it's in D3 mode.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a revised patch based on Mengdong Lin's fix patch, which is a
supplement to a previous patch [1611a9c9: ALSA: hda - Add fixup for
Haswell to enable all pin and convertor widgets].
Some Haswell BIOS will disable the 2nd and 3rd pin/covertor widgets
when the HD-A controller changes state from D3 to D0. So when the
controller resumes after a system or runtime suspend, these widgets
are disabled and programming these widgets to D0 will cause H/W error
and codec will not respond.
In addition, we found out that some BIOS disables the pins at S3
although it shows up at boot. This confuses the driver utterly, and
the hardware falls into the fatal communication error like the above.
So in this patch, we apply intel_haswell_enable_all_pins() not only as
a fixup to a certain device (with 8086:2010) but to all Haswell
machines. The codec driver basically assumes that all pins are
exposed, so it's anyway better to see them from the beginning. Even
if all pins and converters are shown by this call, there should be no
regression in practice: the pin default configurations are still kept,
thus the disabled pins are handled as disabled by the driver
properly.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When graphics initializes the HDMI chip, sometimes this leads to
pins going into D3 and right channel being muted. If the audio driver
finishes initialization before the graphic driver does, this situation
becomes permanent.
This is a workaround that checks for this situation and corrects it on
playback prepare. It has been verified working on at least one machine.
BugLink: https://bugs.launchpad.net/bugs/1167270
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch let ELD debug message show 'pin_eld->monitor_present' which reflects
the real pin response to verb GET_PIN_SENSE.
'eld->monitor_present' should not be used here because 'eld' is a temp
structure now and so its "monitor_present" is not set.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the dynamic array allocations for pins, converters and PCM arrays
instead of the fixed size arrays. The modern HDMI codecs get more and
more pins, and we don't know the sensitive limit.
Most of the patch are spent for the straight conversions from the
fixed array access to snd_array helpers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ELD validity can change during the lifetime of a presence detect,
so we need to be able to listen for changes on the ELD control.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because the eld buffer can be simultaneously accessed from both
workqueue context (updating) and process context (kcontrol read),
we need to protect it with a mutex to guarantee consistency.
To avoid holding the mutex while reading the ELD info from the
codec, we introduce a temporary eld buffer.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For better readability, the information that is parsed out of the
ELD data is now put into a separate parsed_hdmi_eld struct.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously, it was possible to read the eld data of the previous
monitor connected. This should not be allowed.
Also refactor the function slightly.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, eld_valid is never set to false, except at kernel module
load time. This patch makes sure that eld is no longer valid when
the cable is (hot-)unplugged.
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A Haswell test machine showed that the invalid connection list, but
this time it has only a single pin on the codec, thus the former fixup
code doesn't work as it assumes the three pins blindly.
This patch splits the former fixup code to two parts:
- Enable eDP 1.2 for Haswell codec
- Fix the connection list of pins on Haswell codec;
the converter list is recorded dynamically in hdmi_add_cvt(), and
applied in hdmi_add_pin()
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Haswell machines support more than one display outputs (HDMI or DP),
but its BIOS may not enable the codec's 2nd and 3rd pin and output cvt widgets.
This patch implements a board-specific fixup for Intel Haswell Machines:
If the hidden pins are not enabled by BIOS, the driver will enable them
and call common code to update the codec tree.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently we set the max number of connections to be 32, but there
seems codec that gives longer connection lists like AD1988, and we see
errors in proc output and else. (Though, in the case of AD1988, it's
a list of all codecs connected to a single vendor widget, so this must
be something fishy, but it's still valid from the h/w design POV.)
This patch tries to remove this restriction. For efficiency, we still
use the fixed size array in the parser, but takes a dynamic array when
the size is reported to be greater than that.
Now the fixed array size is found only in patch_hdmi.c, but it should
be fine, as the codec itself can't support so many pins.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit d45e6889ee ("ALSA: hda - Provide
the proper channel mapping for generic HDMI driver") added support for
custom channel maps in the HDA HDMI driver. Due to a mistake in an
'if' condition the custom map is always used even when no such map has
been set. This causes incorrect channel mapping for multichannel audio
by default.
Pass per_pin->chmap_set to hdmi_setup_channel_mapping() as a parameter
so that it can use it for detecting if a custom map has been set instead
of checking if map is NULL (which is never the case).
Reported-by: Staffan Lindberg <pike@xbmc.org>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the driver detects and invalid ELD, it gives an open error.
But it forgot to release the assigned pin, converter and spdif ctls
before returning.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When "alsactl restore" is performed on HDMI codecs, it tries to
restore the channel map value since the channel map controls are
writable. But hdmi_chmap_ctl_put() returns -EBADFD when no PCM stream
is assigned yet, and this results in an error message from alsactl.
Although the error is harmless, it's certainly ugly and can be
regarded as a regression.
As a workaround, this patch changes the return code in such a case to
be zero for making others happy. (A slight excuse is: when the chmap
is changed through the proper alsa-lib API, the PCM status is checked
there anyway, so we don't have to be too strict in the kernel side.)
Cc: <stable@vger.kernel.org> [v3.7+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell HDMI codec pins may report invalid connection list entries, which
will cause failure to play audio via HDMI or Display Port.
So this patch adds fixup for Haswell to workaround this hardware issue:
enable DP1.2 mode and override the pins' connection list entries with proper
value.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Xingchao Wang <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've seen the broken HDMI *video* output on some machines with GM965,
and the debugging session pointed that the culprit is the disabled
audio output pins. Toggling these pins dynamically on demand caused
flickering of HDMI TV.
This patch changes the behavior to keep the pin ON constantly.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=51421
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some of the PantherPoint HDMI machines we currently enable, we're seeing
trouble with unsol events, i e detecting monitor presence, especially when
on battery and after suspend/resume.
BugLink: https://bugs.launchpad.net/bugs/1075882
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When both an SPDIF and an HDMI device are created on the same card
instance, multiple IEC958 controls are created with indices=0, 1, ...
But the alsa-lib configuration can't know which index corresponds
actually to which PCM device, and both the SPDIF and the HDMI
configurations point to the first IEC958 control wrongly.
This patch introduces a (hackish and ugly) workaround: the IEC958
controls for the SPDIF device are re-labeled with device=1 when HDMI
coexists. The device=1 corresponds to the actual PCM device for
SPDIF, so it's anyway a better representation. In future, HDMI
controls should be moved with the corresponding PCM device number,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... instead of the standard fixed channel maps.
The generic HDMI is based on the audio infoframe, and its configuration
can be selected via CA bits. Thus we need a translation between the
CA index and the verbose channel map list.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently the check for non-PCM stream state was added to the generic
HDMI driver code. But this check should be done rather to each pin
instead of each converter. Otherwise when a different converter is
assigned at the next open, the audio infoframe can be inconsistent
with the setup using the previous converter.
For fixing this issue, this patch moves the state of the current
non-PCM status from per_cvt to per_pin. (In addition an unused
argument cvt_nid is stripped from hdmi_setup_channel_mapping())
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For HBR stream test, use straight channel mapping way.
when switched back to "speaker-test -c8", even the audio
infoframe is up-to-date, there should be correct channel mapping setup.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDMI channel remapping apparently effects HBR packets on Intel's chips.
For compressed non-PCM audio, use "straight-through" channel mapping.
For uncompressed multi-channel pcm audio, use normal channel mapping.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The array channel_allocations[] is an ordered list, add function to get
correct order by ca_index.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_SND_HDA_POWER_SAVE is no longer an experimental feature and its
behavior can be well controlled via the default value and module
parameter. Let's just replace it with the standard CONFIG_PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling the jack sync in the init callback of each codec,
call it generically at initialization and resume. By calling it at
the last of resume sequence, a possible race between the jack sync and
the unsol event enablement in the current code will be closed, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit c4bfe94a causes a regression on some codecs at probing.
Since this was just a workaround to shut up a kernel warning, it'd be
better to revert and fix properly. So we ended up with re-adding the
cleanup callback.
Tested-and-reported-by: Matt Horan <matt@matthoran.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix to converter detaching timing in patch_hdmi.c
leads to a kernel WARNING due to a sanity check when the debug
option is set. Add a workaround by setting a dummy hinfo->nid.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The generic HDMI code detaches the converter from the stream when
unused, but it must be done rather in the close callback instead of
the cleanup callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Turn on the pin widget's PIN_OUT bit from playback prepare. The pin is
enabled in open, but is disabled in hdmi_init_pin which is called during
system resume. This causes a system suspend/resume during playback to
mute HDMI/DP. Enabling the pin in prepare instead of open allows calling
snd_pcm_prepare after a system resume to restore audio.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0051 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Acked-by: Andy Ritger <aritger@nvidia.com>
Reviewed-by: Daniel Dadap <ddadap@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the recent code, the value shown there is a tag number, and it's no
longer same as the pin nid. Correct the message to avoid confusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VIA codecs seem not returning the event tag in the unsolicited events,
thus the current code relying on the tag value doesn't work.
Since simple_hdmi stuff has only a single pin, we can use simply
snd_hda_jack_set_dirty_all() to activate the pin-detection
independently from the tag value.
Tested-by: Annie Liu <AnnieLiu@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The simple_hdmi stuff is designed only for a single pin and a single
converter (thus a single PCM stream), and no need for loops.
Let's flatten the code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The codes to initialize work struct or create a proc interface should
be called only once and never although it's called many times through
the init callback. Move that stuff into patch_generic_hdmi() so that
it's called only once.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes the regression introduced by the commit d0b1252d for
refactoring simple_hdmi*(). The pin NID wasn't assigned correctly.
Reported-by: Annie Liu <annieliu@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Wang Xingchao