cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----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=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
The UFS_RESET pin is the magical pin #150 now, not 153 per the
sdm845_groups array declared in this file. Fix the order of pins so that
UFS_RESET is 150 and the SDC pins follow after.
Fixes: 53a5372ce3 ("pinctrl: qcom: sdm845: Expose ufs_reset as gpio")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190830060227.12792-1-swboyd@chromium.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After we switched the two drivers that have .need_valid_mask
set to use the callback for setting up the .valid_mask,
we can just use the presence of the .init_valid_mask()
callback (or the OF reserved ranges, nota bene) to determine
whether to allocate the mask or not and we can drop the
.need_valid_mask field altogether.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819093058.10863-1-linus.walleij@linaro.org
It is more helpful for drivers to have the affected fields
directly available when we use the callback to set up the
valid mask. Change this and switch over the only user
(MSM) to use the passed parameters. If we do this we can
also move the mask out of publicly visible struct fields.
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819084904.30027-1-linus.walleij@linaro.or
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the GPIO core has support for hierarchical IRQ chips, convert
Qualcomm's spmi-gpio over to use these new helpers to reduce duplicated
code across drivers.
This change was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190808123242.5359-3-linus.walleij@linaro.org
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-34-swboyd@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When fall-through warnings was enabled by default the following warnings
was starting to show up:
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c: In function ‘pmic_gpio_populate’:
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:815:20: warning: this statement may fall
through [-Wimplicit-fallthrough=]
pad->have_buffer = true;
~~~~~~~~~~~~~~~~~^~~~~~
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:816:2: note: here
case PMIC_GPIO_SUBTYPE_GPIOC_4CH:
^~~~
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:820:20: warning: this statement may fall
through [-Wimplicit-fallthrough=]
pad->have_buffer = true;
~~~~~~~~~~~~~~~~~^~~~~~
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:821:2: note: here
case PMIC_GPIO_SUBTYPE_GPIOC_8CH:
^~~~
Rework so that the compiler doesn't warn about fall-through.
Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20190726112816.19723-1-anders.roxell@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TSIF is the Transport Stream Interface.
First, rename tsif1 to tsif0, and tsif2 to tsif1.
Then squash all 5 tsif0 pins into a single function.
Same for tsif1.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Link: https://lore.kernel.org/r/503b2ae8-ead6-70cd-7b21-ce5f5166a23a@free.fr
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Lina Iyer <ilina@codeaurora.org>
Link: https://lore.kernel.org/r/20190724083828.7496-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Add initial pinctrl driver to support pin configuration with
pinctrl framework for SM8150
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org>
[vkoul: modify to use upstream tile support
use upstream code style
order the functions and squash functions]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190702105045.27646-4-vkoul@kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce the irq_enable callback which will be same as irq_unmask
except that it will also clear the status bit before unmask.
This will help in clearing any erroneous interrupts that would
have got latched when the interrupt is not in use.
There may be devices like UART which can use the same gpio line
for data rx as well as a wakeup gpio when in suspend. The data that
was flowing on the line may latch the interrupt and when we enable
the interrupt before going to suspend, this would trigger the
unexpected interrupt. This change helps clearing the interrupt
so that these unexpected interrupts gets cleared.
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Link: https://lore.kernel.org/r/1561472086-23360-1-git-send-email-neeraju@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns when CONFIG_ACPI is unset:
drivers/pinctrl/qcom/pinctrl-sdm845.c:1320:5: warning: 'CONFIG_ACPI' is
not defined, evaluates to 0 [-Wundef]
#if CONFIG_ACPI
^
1 warning generated.
Use ifdef instead of if to resolve this.
Fixes: a229105d7a ("pinctrl: qcom: sdm845: Provide ACPI support")
Link: https://github.com/ClangBuiltLinux/linux/issues/569
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides basic support for booting with ACPI instead
of the currently supported Device Tree. When doing so there are a
couple of differences which we need to taken into consideration.
Firstly, the SDM850 ACPI tables omit information pertaining to the
4 reserved GPIOs on the platform. If Linux attempts to touch/
initialise any of these lines, the firmware will restart the
platform.
Secondly, when booting with ACPI, it is expected that the firmware
will set-up things like; Regulators, Clocks, Pin Functions, etc in
their ideal configuration. Thus, the possible Pin Functions
available to this platform are not advertised when providing the
higher GPIOD/Pinctrl APIs with pin information.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When booting MSM based platforms with Device Tree or some ACPI
implementations, it is possible to provide a list of reserved pins
via the 'gpio-reserved-ranges' and 'gpios' properties respectively.
However some ACPI tables are not populated with this information,
thus it has to come from a knowledgable device driver instead.
Here we provide the MSM common driver with additional support to
parse this informtion and correctly populate the widely used
'valid_mask'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ufs_reset pin is expected to be wired to the reset pin of the
primary UFS memory but is pretty much just a general purpose output pinr
Reorder the pins and expose it as gpio 150, so that the UFS driver can
toggle it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements.
-----BEGIN PGP SIGNATURE-----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=EfXK
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is a calm cycle, not much happened this time around: not even
much incremental development. Some three new drivers, that is all.
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements"
* tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits)
pinctrl: imx: fix scu link errors
dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding
pinctrl: qcom: spmi-gpio: Reorder debug print
pinctrl: nomadik: fix possible object reference leak
pinctrl: stm32: return error upon hwspinlock failure
pinctrl: stm32: fix memory leak issue
pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
pinctrl: sh-pfc: Validate fixed-size field widths at build time
pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups
pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
pinctrl: sh-pfc: emev2: Add missing pinmux functions
pinctrl: sunxi: Support I/O bias voltage setting on A80
pinctrl: ingenic: Add LCD pins for the JZ4725B SoC
pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask
pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl
pinctrl: bcm2835: declare pin config as generic
pinctrl: qcom: qcs404: Drop unused UFS_RESET macro
dt-bindings: add documentation for slew rate
...
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----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=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
It's reasonable to expect that people turn to the "gpio" debugfs file to
first and foremost learn about the direction and value of a gpio, and
second to that about it's pinconf. So reorder the value so each line
reads:
gpioN: direction value ...
This also makes it consistent with the TLMM pinctrl driver's output in
the same dump.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SSBI GPIOs are numbered 1..ngpio, so the boundary check in
pm8xxx_domain_translate() is off by one. This patch corrects that check.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ssbi-gpio did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should
be usable from the start without the consumer having to make an
additional call to get the proper IRQ on the parent. This patch adds
hierarchical IRQ chip support to the ssbi-gpio code to correct this
issue.
The constant PM8XXX_GPIO_PHYSICAL_OFFSET is introduced to replace the
hardcoded '1' that previously existed in two places in this driver to
improve code readability.
This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process. This change will also
allow for the removal of the interrupts property later in this
patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,ssbi-gpio OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs on the SPMI PMIC are numbered 1..ngpio, so the boundary check in
pmic_gpio_domain_translate() is off by one, correct this.
Fixes: ca69e2d165 ("qcom: spmi-gpio: add support for hierarchical IRQ chip")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SDC controls live in the south tile, not the north one. Correct this
so that we program the right registers.
Cc: stable@vger.kernel.org
Fixes: 22eb8301db ("pinctrl: qcom: Add qcs404 pinctrl driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The UFS_RESET macro serves no purpose on QCS404, remove it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Select IRQ_DOMAIN_HIERARCHY for spmi-gpio in Kconfig since this driver
is now setup as a hierarchical IRQ chip.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
spmi-gpio did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should
be usable from the start without the consumer having to make an
additional call to get the proper IRQ on the parent. This patch adds
hierarchical IRQ chip support to the spmi-gpio code to correct this
issue.
Driver was tested using the volume buttons (via gpio-keys) on the LG
Nexus 5 (hammerhead) phone with the following two configurations.
volume-up {
interrupts-extended = <&pm8941_gpios 2 IRQ_TYPE_EDGE_BOTH>;
...
};
volume-up {
gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
...
};
Both configurations now show that spmi-gpio is the IRQ domain and that
the IRQ is setup in a hierarchy.
$ grep volume_up /proc/interrupts
72: 6 0 spmi-gpio 1 Edge volume_up
$ cat /sys/kernel/debug/irq/irqs/72
handler: handle_edge_irq
device: (null)
status: 0x00000403
_IRQ_NOPROBE
istate: 0x00000000
ddepth: 0
wdepth: 0
dstate: 0x02400203
IRQ_TYPE_EDGE_RISING
IRQ_TYPE_EDGE_FALLING
IRQD_ACTIVATED
IRQD_IRQ_STARTED
node: 0
affinity: 0-3
effectiv:
domain: :soc:spmi@fc4cf000:pm8941@0:gpios@c000
hwirq: 0x1
chip: spmi-gpio
flags: 0x4
IRQCHIP_MASK_ON_SUSPEND
parent:
domain: :soc:spmi@fc4cf000
hwirq: 0xc100057
chip: pmic_arb
flags: 0x4
IRQCHIP_MASK_ON_SUSPEND
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process. This change will also
allow for the removal of the interrupts property later in this
patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,spmi-gpio OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
The pm8941 code was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for qcom,pm8005-gpio, qcom,pm8998-gpio, and
qcom,pmi8998-gpio. These three variants are already in use in some
arm64 dtsi files. Those boards work since the generic binding
qcom,spmi-gpio is also specified.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time.
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins
with another CPU using a hardware spinlock.
-----BEGIN PGP SIGNATURE-----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=cm6m
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"We have no core changes but lots of incremental development in drivers
all over the place: Renesas, NXP, Mediatek and Actions Semiconductor
keep churning out new SoCs.
I have some subtree maintainers for Renesas and Intel helping out to
keep down the load, it's been working smoothly (Samsung also have a
subtree but it was not used this cycle.)
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins with
another CPU using a hardware spinlock"
* tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits)
dt-bindings: arm: fsl-scu: add imx8qm pinctrl support
pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ
pinctrl: imx-scu: Depend on IMX_SCU
pinctrl: ocelot: Add dependency on HAS_IOMEM
pinctrl: ocelot: add MSCC Jaguar2 support
pinctrl: bcm: ns: support updated DT binding as syscon subnode
dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon
MAINTAINERS: merge at91 pinctrl entries
pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP
pinctrl: uniphier: constify uniphier_pinctrl_socdata
pinctrl: mediatek: improve Kconfig dependencies
pinctrl: msm: mark PM functions as __maybe_unused
dt-bindings: pinctrl: sunxi: Add supply properties
pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins
pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins
pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length
...
Without CONFIG_PM_SLEEP, we get annoying warnings about unused functions:
drivers/pinctrl/qcom/pinctrl-msm.c:1082:12: error: 'msm_pinctrl_resume' defined but not used [-Werror=unused-function]
static int msm_pinctrl_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~
drivers/pinctrl/qcom/pinctrl-msm.c:1075:12: error: 'msm_pinctrl_suspend' defined but not used [-Werror=unused-function]
static int msm_pinctrl_suspend(struct device *dev)
Mark them as __maybe_unused to shut up the warning and silently drop
the functions without having to add ugly #ifdefs.
Fixes: 977d057ad3 ("pinctrl: msm: Add sleep pinctrl state transitions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This was missed when tiles support was added in a revison and
causes the driver to fail to load.
Fixes: 9cf0c526bc ("pinctrl: qcom: Add sdm660 pinctrl driver")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add PM suspend callbacks to the msm core driver that select the
sleep and default pinctrl states. Then wire those callbacks up
in the sdm845 driver, for those boards that may have GPIO hogs
that need to change state during suspend.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When attempting to setup up a gpio hog, device probing will repeatedly
fail with -EPROBE_DEFERED errors. It is caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.
See Christian Lamparter's commit a86caa9ba5 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.
I did not test this change against any hardware supported by this
particular driver, however I was able to validate this same fix works
for pinctrl-spmi-gpio.c using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When attempting to setup up a gpio hog, device probing would repeatedly
fail with -EPROBE_DEFERED errors. It was caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.
See Christian Lamparter's commit a86caa9ba5 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
The current code produces XPU violation if get_direction is called just
after the initialization.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'tiles' array is initialized to a constant pointers to constant
strings, but the declaration is only half as constant:
drivers/pinctrl/qcom/pinctrl-qcs404.c:1660:11: error: initialization discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
drivers/pinctrl/qcom/pinctrl-sdm660.c:1417:11: error: initialization discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
Let's make it more constant.
Fixes: 22eb8301db ("pinctrl: qcom: Add qcs404 pinctrl driver")
Fixes: a46d5e9819 ("pinctrl: qcom: Support dispersed tiles")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This code needs to select function #0, which is the first int in the
array of functions, not the number 0 which may or may not be the
function for "GPIO mode" per the enum mapping. We were getting lucky on
SDM845, where this was tested, because the function 0 matched the enum
value for "GPIO mode". On other platforms, e.g. MSM8996, the gpio enum
value is the last one in the list so this code doesn't work and we see a
warning at boot. Fix it by grabbing the first element out of the array
of functions.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Fixes: 1de7ddb3a1 ("pinctrl: msm: Mux out gpio function with gpio_request()")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds