This enables module_alloc() to allocate huge page for 2MB+ requests.
To check the difference of this change, we need enable config
CONFIG_PTDUMP_DEBUGFS, and call module_alloc(2MB). Before the change,
/sys/kernel/debug/page_tables/kernel shows pte for this map. With the
change, /sys/kernel/debug/page_tables/ show pmd for thie map.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220204185742.271030-2-song@kernel.org
On changing the RX ring parameters igb uses a hack to avoid a warning
when calling xdp_rxq_info_reg via igb_setup_rx_resources. It just
clears the struct xdp_rxq_info content.
Instead, change this to unregister if we're already registered. Align
code to the igc code.
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mauricio Vásquez <mauricio@kinvolk.io> says:
====================
This series fixes a bad calculation of strict mode in two places. It
also updates libbpf to make it easier for the users to disable a
specific LIBBPF_STRICT_* flag.
v1 -> v2:
- remove check in libbpf_set_strict_mode()
- split in different commits
v1: https://lore.kernel.org/bpf/20220204220435.301896-1-mauricio@kinvolk.io/
====================
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
"(__LIBBPF_STRICT_LAST - 1) & ~LIBBPF_STRICT_MAP_DEFINITIONS" is wrong
as it is equal to 0 (LIBBPF_STRICT_NONE). Let's use
"LIBBPF_STRICT_ALL & ~LIBBPF_STRICT_MAP_DEFINITIONS" now that the
previous commit makes it possible in libbpf.
Fixes: 93b8952d22 ("libbpf: deprecate legacy BPF map definitions")
Signed-off-by: Mauricio Vásquez <mauricio@kinvolk.io>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220207145052.124421-4-mauricio@kinvolk.io
"(__LIBBPF_STRICT_LAST - 1) & ~LIBBPF_STRICT_MAP_DEFINITIONS" is wrong
as it is equal to 0 (LIBBPF_STRICT_NONE). Let's use
"LIBBPF_STRICT_ALL & ~LIBBPF_STRICT_MAP_DEFINITIONS" now that the
previous commit makes it possible in libbpf.
Fixes: 93b8952d22 ("libbpf: deprecate legacy BPF map definitions")
Signed-off-by: Mauricio Vásquez <mauricio@kinvolk.io>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220207145052.124421-3-mauricio@kinvolk.io
libbpf_set_strict_mode() checks that the passed mode doesn't contain
extra bits for LIBBPF_STRICT_* flags that don't exist yet.
It makes it difficult for applications to disable some strict flags as
something like "LIBBPF_STRICT_ALL & ~LIBBPF_STRICT_MAP_DEFINITIONS"
is rejected by this check and they have to use a rather complicated
formula to calculate it.[0]
One possibility is to change LIBBPF_STRICT_ALL to only contain the bits
of all existing LIBBPF_STRICT_* flags instead of 0xffffffff. However
it's not possible because the idea is that applications compiled against
older libbpf_legacy.h would still be opting into latest
LIBBPF_STRICT_ALL features.[1]
The other possibility is to remove that check so something like
"LIBBPF_STRICT_ALL & ~LIBBPF_STRICT_MAP_DEFINITIONS" is allowed. It's
what this commit does.
[0]: https://lore.kernel.org/bpf/20220204220435.301896-1-mauricio@kinvolk.io/
[1]: https://lore.kernel.org/bpf/CAEf4BzaTWa9fELJLh+bxnOb0P1EMQmaRbJVG0L+nXZdy0b8G3Q@mail.gmail.com/
Fixes: 93b8952d22 ("libbpf: deprecate legacy BPF map definitions")
Signed-off-by: Mauricio Vásquez <mauricio@kinvolk.io>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220207145052.124421-2-mauricio@kinvolk.io
Some of the tests are using x86_64 ABI-specific syscall entry points
(such as __x64_sys_nanosleep and __x64_sys_getpgid). Update them to use
architecture-dependent syscall entry names.
Also update fexit_sleep test to not use BPF_PROG() so that it is clear
that the syscall parameters aren't being accessed in the bpf prog.
Note that none of the bpf progs in these tests are actually accessing
any of the syscall parameters. The only exception is perfbuf_bench, which
passes on the bpf prog context into bpf_perf_event_output() as a pointer
to pt_regs, but that looks to be mostly ignored.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/e35f7051f03e269b623a68b139d8ed131325f7b7.1643973917.git.naveen.n.rao@linux.vnet.ibm.com
On architectures that don't use a syscall wrapper, sys_* function names
are set as an alias of __se_sys_* functions. Due to this, there is no
BTF associated with sys_* function names. This results in some of the
test progs failing to load. Set the SYS_PREFIX to "__se_" to fix this
issue.
Fixes: 38261f369f ("selftests/bpf: Fix probe_user test failure with clang build kernel")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/013d632aacd3e41290445c0025db6a7055ec6e18.1643973917.git.naveen.n.rao@linux.vnet.ibm.com
Call mv88e6xxx_reg_unlock(chip) before returning on this error path.
Fixes: 7af4a361a6 ("net: dsa: mv88e6xxx: Improve isolation of standalone ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The <= ARRAY_SIZE() needs to be < ARRAY_SIZE() to prevent an out of
bounds error.
Fixes: d4ebf12bce ("net: dsa: mv88e6xxx: populate supported_interfaces and mac_capabilities")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the device that supports the TX push capability, the BD can
be directly copied to the device memory. However, due to hardware
restrictions, the push mode can be used only when there are no
more than two BDs, otherwise, the doorbell mode based on device
memory is used.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot once again hit uninit value in asix driver. The problem still the
same -- asix_read_cmd() reads less bytes, than was requested by caller.
Since all read requests are performed via asix_read_cmd() let's catch
usb related error there and add __must_check notation to be sure all
callers actually check return value.
So, this patch adds sanity check inside asix_read_cmd(), that simply
checks if bytes read are not less, than was requested and adds missing
error handling of asix_read_cmd() all across the driver code.
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Reported-and-tested-by: syzbot+6ca9f7867b77c2d316ac@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8168d_2_hw_phy_config() shares quite some functionality with
rtl8168d_1_hw_phy_config(), so let's factor out the common part to a
new function rtl8168d_1_common(). In addition improve the code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Add SIP and DIP mangling support
Danielle says:
On Spectrum-2 onwards, it is possible to overwrite SIP and DIP address
of an IPv4 or IPv6 packet in the ACL engine. That corresponds to pedit
munges of, respectively, ip src and ip dst fields, and likewise for ip6.
Offload these munges on the systems where they are supported.
Patchset overview:
Patch #1: introduces SIP_DIP_ACTION and its fields.
Patch #2-#3: adds the new pedit fields, and dispatches on them on
Spectrum-2 and above.
Patch #4 adds a selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks that pedit adjusts source and destination
addresses of IPv4 and IPv6 packets.
Output example:
$ ./pedit_ip.sh
TEST: ping [ OK ]
TEST: ping6 [ OK ]
TEST: dev swp2 ingress pedit ip src set 198.51.100.1 [ OK ]
TEST: dev swp3 egress pedit ip src set 198.51.100.1 [ OK ]
TEST: dev swp2 ingress pedit ip dst set 198.51.100.1 [ OK ]
TEST: dev swp3 egress pedit ip dst set 198.51.100.1 [ OK ]
TEST: dev swp2 ingress pedit ip6 src set 2001:db8:2::1 [ OK ]
TEST: dev swp3 egress pedit ip6 src set 2001:db8:2::1 [ OK ]
TEST: dev swp2 ingress pedit ip6 dst set 2001:db8:2::1 [ OK ]
TEST: dev swp3 egress pedit ip6 dst set 2001:db8:2::1 [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 supports an ACL action SIP_DIP, which allows IPv4 and IPv6
source and destination addresses change. Offload suitable mangles to
the IPv6 address change action.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 supports an ACL action SIP_DIP, which allows IPv4 and IPv6
source and destination addresses change. Offload suitable mangles to
the IPv4 address change action.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fields related to SIP_DIP_ACTION, which is used for changing of SIP
and DIP addresses.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Menglong Dong says:
====================
net: use kfree_skb_reason() for ip/udp packet receive
In this series patches, kfree_skb() is replaced with kfree_skb_reason()
during ipv4 and udp4 packet receiving path, and following drop reasons
are introduced:
SKB_DROP_REASON_SOCKET_FILTER
SKB_DROP_REASON_NETFILTER_DROP
SKB_DROP_REASON_OTHERHOST
SKB_DROP_REASON_IP_CSUM
SKB_DROP_REASON_IP_INHDR
SKB_DROP_REASON_IP_RPFILTER
SKB_DROP_REASON_UNICAST_IN_L2_MULTICAST
SKB_DROP_REASON_XFRM_POLICY
SKB_DROP_REASON_IP_NOPROTO
SKB_DROP_REASON_SOCKET_RCVBUFF
SKB_DROP_REASON_PROTO_MEM
TCP is more complex, so I left it in the next series.
I just figure out how __print_symbolic() works. It doesn't base on the
array index, but searching for symbols by loop. So I'm a little afraid
it's performance.
Changes since v3:
- fix some small problems in the third patch (net: ipv4: use
kfree_skb_reason() in ip_rcv_core()), as David Ahern said
Changes since v2:
- use SKB_DROP_REASON_PKT_TOO_SMALL for a path in ip_rcv_core()
Changes since v1:
- add document for all drop reasons, as David advised
- remove unreleated cleanup
- remove EARLY_DEMUX and IP_ROUTE_INPUT drop reason
- replace {UDP, TCP}_FILTER with SOCKET_FILTER
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in __udp_queue_rcv_skb().
Following new drop reasons are introduced:
SKB_DROP_REASON_SOCKET_RCVBUFF
SKB_DROP_REASON_PROTO_MEM
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in udp_queue_rcv_one_skb().
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in ip_protocol_deliver_rcu().
Following new drop reasons are introduced:
SKB_DROP_REASON_XFRM_POLICY
SKB_DROP_REASON_IP_NOPROTO
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in ip_rcv_finish_core(),
following drop reasons are introduced:
SKB_DROP_REASON_IP_RPFILTER
SKB_DROP_REASON_UNICAST_IN_L2_MULTICAST
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in ip_rcv_core(). Three new
drop reasons are introduced:
SKB_DROP_REASON_OTHERHOST
SKB_DROP_REASON_IP_CSUM
SKB_DROP_REASON_IP_INHDR
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in nf_hook_slow() when
skb is dropped by reason of NF_DROP. Following new drop reasons
are introduced:
SKB_DROP_REASON_NETFILTER_DROP
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add document for following existing drop reasons:
SKB_DROP_REASON_NOT_SPECIFIED
SKB_DROP_REASON_NO_SOCKET
SKB_DROP_REASON_PKT_TOO_SMALL
SKB_DROP_REASON_TCP_CSUM
SKB_DROP_REASON_SOCKET_FILTER
SKB_DROP_REASON_UDP_CSUM
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit e940066089 ("lib/stackdepot: always do filter_irq_stacks()
in stack_depot_save()") it became unnecessary to filter the stack
before calling stack_depot_save().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing a patch that will follow later
("net: add netns refcount tracker to struct nsproxy")
I found that devtmpfs_init() was called before init_net
was initialized.
This is a bug, because devtmpfs_setup() calls
ksys_unshare(CLONE_NEWNS);
This has the effect of increasing init_net refcount,
which will be later overwritten to 1, as part of setup_net(&init_net)
We had too many prior patches [1] trying to work around the root cause.
Really, make sure init_net is in BSS section, and that net_ns_init()
is called earlier at boot time.
Note that another patch ("vfs: add netns refcount tracker
to struct fs_context") also will need net_ns_init() being called
before vfs_caches_init()
As a bonus, this patch saves around 4KB in .data section.
[1]
f8c46cb390 ("netns: do not call pernet ops for not yet set up init_net namespace")
b5082df801 ("net: Initialise init_net.count to 1")
734b65417b ("net: Statically initialize init_net.dev_base_head")
v2: fixed a build error reported by kernel build bots (CONFIG_NET=n)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, HSR manages mac addresses of known HSR nodes by using list_head.
It takes a lot of time when there are a lot of registered nodes due to
finding specific mac address nodes by using linear search. We can be
reducing the time by using hlist. Thus, this patch moves list_head to
hlist_head for mac addresses and this allows for further improvement of
network performance.
Condition: registered 10,000 known HSR nodes
Before:
# iperf3 -c 192.168.10.1 -i 1 -t 10
Connecting to host 192.168.10.1, port 5201
[ 5] local 192.168.10.2 port 59442 connected to 192.168.10.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.49 sec 3.75 MBytes 21.1 Mbits/sec 0 158 KBytes
[ 5] 1.49-2.05 sec 1.25 MBytes 18.7 Mbits/sec 0 166 KBytes
[ 5] 2.05-3.06 sec 2.44 MBytes 20.3 Mbits/sec 56 16.9 KBytes
[ 5] 3.06-4.08 sec 1.43 MBytes 11.7 Mbits/sec 11 38.0 KBytes
[ 5] 4.08-5.00 sec 951 KBytes 8.49 Mbits/sec 0 56.3 KBytes
After:
# iperf3 -c 192.168.10.1 -i 1 -t 10
Connecting to host 192.168.10.1, port 5201
[ 5] local 192.168.10.2 port 36460 connected to 192.168.10.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 7.39 MBytes 62.0 Mbits/sec 3 130 KBytes
[ 5] 1.00-2.00 sec 5.06 MBytes 42.4 Mbits/sec 16 113 KBytes
[ 5] 2.00-3.00 sec 8.58 MBytes 72.0 Mbits/sec 42 94.3 KBytes
[ 5] 3.00-4.00 sec 7.44 MBytes 62.4 Mbits/sec 2 131 KBytes
[ 5] 4.00-5.07 sec 8.13 MBytes 63.5 Mbits/sec 38 92.9 KBytes
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have plans for increasing MAX_SKB_FRAGS, but sk_msg_sg::copy
is currently an unsigned long, limiting MAX_SKB_FRAGS to 30 on 32bit arches.
Convert it to a bitmap, as Jakub suggested.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of disabling TSO at compile time if MAX_SKB_FRAGS > 32,
implement ndo_features_check() method for this driver for
a more dynamic handling.
If skb has more than 32 frags and is a GSO packet, force
software segmentation.
Most locally generated packets will use a small number
of fragments anyway.
For forwarding workloads, we can limit gro_max_size at ingress,
we might also implement gro_max_segs if needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems this one-element array is not actually being used as an
array of variable size, so we can just replace it with just a
non-array object of type struct desc_frag and refactor a bit the
rest of the code.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang says:
====================
net: mana: Add handling of CQE_RX_TRUNCATED and a cleanup
Add handling of CQE_RX_TRUNCATED and a cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch statement already ensures cqe_type == CQE_RX_OKAY at that
point.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The proper way to drop this kind of CQE is advancing rxq tail
without indicating the packet to the upper network layer.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: device tracking improvements
Main goal of this series is to be able to detect the following case
which apparently is still haunting us.
dev_hold_track(dev, tracker_1, GFP_ATOMIC);
dev_hold(dev);
dev_put(dev);
dev_put(dev); // Should complain loudly here.
dev_put_track(dev, tracker_1); // instead of here (as before this series)
v2: third patch:
I replaced the dev_put() in linkwatch_do_dev() with __dev_put().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We are still chasing some syzbot reports where we think a rogue dev_put()
is called with no corresponding prior dev_hold().
Unfortunately it eats a reference on dev->dev_refcnt taken by innocent
dev_hold_track(), meaning that the refcount saturation splat comes
too late to be useful.
Make sure that 'not tracked' dev_put() and dev_hold() better use
CONFIG_NET_DEV_REFCNT_TRACKER=y debug infrastructure:
Prior patch in the series allowed ref_tracker_alloc() and ref_tracker_free()
to be called with a NULL @trackerp parameter, and to use a separate refcount
only to detect too many put() even in the following case:
dev_hold_track(dev, tracker_1, GFP_ATOMIC);
dev_hold(dev);
dev_put(dev);
dev_put(dev); // Should complain loudly here.
dev_put_track(dev, tracker_1); // instead of here
Add clarification about netdev_tracker_alloc() role.
v2: I replaced the dev_put() in linkwatch_do_dev()
with __dev_put() because callers called netdev_tracker_free().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are still chasing a netdev refcount imbalance, and we suspect
we have one rogue dev_put() that is consuming a reference taken
from a dev_hold_track()
To detect this case, allow ref_tracker_alloc() and ref_tracker_free()
to be called with a NULL @trackerp parameter, and use a dedicated
refcount_t just for them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever ref_tracker_dir_init() is called, mark the struct ref_tracker_dir
as dead.
Test the dead status from ref_tracker_alloc() and ref_tracker_free()
This should detect buggy dev_put()/dev_hold() happening too late
in netdevice dismantle process.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
ipv6: mc_forwarding changes
First patch removes minor data-races, as mc_forwarding can
be locklessly read in fast path.
Second patch adds a short cut in ip6mr_sk_done()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In many cases, ip6mr_sk_done() is called while no ipmr socket
has been registered.
This removes 4 rtnl acquisitions per netns dismantle,
with following callers:
igmp6_net_exit(), tcpv6_net_exit(), ndisc_net_exit()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes minor data-races in ip6_mc_input() and
batadv_mcast_mla_rtr_flags_softif_get_ipv6()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We generally default the vendor to y and the drivers itself
to n. NET_DSA_REALTEK, however, selects a whole bunch of things,
so it's not a pure "vendor selection" knob. Let's default it all
to n.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink will use PCS polling whenever phylink_config.pcs_poll or the
phylink_pcs poll member is set. As this driver sets both, remove the
former.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_set_10g_modes() is no longer used with the conversion of
drivers to phylink_generic_validate(), so we can remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Song Liu