There are many, many xfs header files which are included but
unneeded (or included twice) in the xfs code, so remove them.
nb: xfs_linux.h includes about 9 headers for everyone, so those
explicit includes get removed by this. I'm not sure what the
preference is, but if we wanted explicit includes everywhere,
a followup patch could remove those xfs_*.h includes from
xfs_linux.h and move them into the files that need them.
Or it could be left as-is.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
During testing of xfs/141 on a V4 filesystem, I observed some
inconsistent behavior with regards to resources that are held (i.e.
remain locked) across a defer roll. The transaction roll always gives
the defer roll function a new transaction, even if committing the old
transaction fails. However, the defer roll function only rejoins the
held resources if the transaction commit succeedied. This means that
callers of defer roll have to figure out whether the held resources are
attached to the transaction being passed back.
Worse yet, if the defer roll was part of a defer finish call, we have a
third possibility: the defer finish could pass back a dirty transaction
with dirty held resources and an error code.
The only sane way to handle all of these scenarios is to require that
the code that held the resource either cancel the transaction before
unlocking and releasing the resources, or use functions that detach
resources from a transaction properly (e.g. xfs_trans_brelse) if they
need to drop the reference before committing or cancelling the
transaction.
In order to make this so, change the defer roll code to join held
resources to the new transaction unconditionally and fix all the bhold
callers to release the held buffers correctly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Colin Ian King reports that commit 82ff27bc52 ("xfs: automatic dfops
buffer relogging") leaves around some dead error handling code in
xfs_dquot_disk_alloc(). This was discovered via Coverity scan.
Since the associated commit eliminates the act of joining a buffer
to a dfops, this intermediate error state is no longer possible and
the error handling code can be removed. Since the caller cancels the
transaction on error, which cancels the dfops, eliminate the
unnecessary xfs_defer_cancel() call and error handling labels.
Fixes: 82ff27bc52 ("xfs: automatic dfops buffer relogging")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The current semantics of xfs_defer_finish() require the caller to
call xfs_defer_cancel() on error. This is slightly inconsistent with
transaction commit error handling where a failed commit cleans up
the transaction before returning.
More significantly, the only requirement for exposure of
->dop_pending outside of xfs_defer_finish() is so that
xfs_defer_cancel() can drain it on error. Since the only recourse of
xfs_defer_finish() errors is cancellation, mirror the transaction
logic and cancel remaining dfops before returning from
xfs_defer_finish() with an error.
Beside simplifying xfs_defer_finish() semantics, this ensures that
xfs_defer_finish() always returns with an empty ->dop_pending and
thus facilitates removal of the list from xfs_defer_ops.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Buffers that are held across deferred operations are explicitly
joined to the dfops structure to ensure appropriate relogging.
While buffers are currently joined explicitly, we can detect the
conditions that require relogging at dfops finish time by inspecting
the transaction item list for held buffers.
Replace the xfs_defer_bjoin() infrastructure with such detection and
automatic relogging of held buffers. This eliminates the need for
the per-dfops buffer list, replaced by an on-stack variant in
xfs_defer_trans_roll().
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Every caller of xfs_defer_finish() now passes the transaction and
its associated ->t_dfops. The xfs_defer_ops parameter is therefore
no longer necessary and can be removed.
Since most xfs_defer_finish() callers also have to consider
xfs_defer_cancel() on error, update the latter to also receive the
transaction for consistency. The log recovery code contains an
outlier case that cancels a dfops directly without an available
transaction. Retain an internal wrapper to support this outlier case
for the time being.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
At this point, the transaction subsystem completely manages deferred
items internally such that the common and boilerplate
xfs_trans_alloc() -> xfs_defer_init() -> xfs_defer_finish() ->
xfs_trans_commit() sequence can be replaced with a simple
transaction allocation and commit.
Remove all such boilerplate deferred ops code. In doing so, we
change each case over to use the dfops in the transaction and
specifically eliminate:
- The on-stack dfops and associated xfs_defer_init() call, as the
internal dfops is initialized on transaction allocation.
- xfs_bmap_finish() calls that precede a final xfs_trans_commit() of
a transaction.
- xfs_defer_cancel() calls in error handlers that precede a
transaction cancel.
The only deferred ops calls that remain are those that are
non-deterministic with respect to the final commit of the associated
transaction or are open-coded due to special handling.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
All but one caller of xfs_defer_init() passes in the ->t_firstblock
of the associated transaction. The one outlier is
xlog_recover_process_intents(), which simply passes a dummy value
because a valid pointer is required. This firstblock variable can
simply be removed.
At this point we could remove the xfs_defer_init() firstblock
parameter and initialize ->t_firstblock directly. Even that is not
necessary, however, because ->t_firstblock is automatically
reinitialized in the new transaction on a transaction roll. Since
xfs_defer_init() should never occur more than once on a particular
transaction (since the corresponding finish will roll it), replace
the reinit from xfs_defer_init() with an assert that verifies the
transaction has a NULLFSBLOCK firstblock.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
All callers pass ->t_firstblock from the current transaction.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Convert all xfs_bmapi_write() users to ->t_firstblock.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Most callers of xfs_defer_init() immediately attach the dfops
structure to a transaction. Add a transaction parameter to eliminate
much of this boilerplate code. This also helps self-document the
fact that many codepaths now expect a dfops pointer implicitly via
xfs_trans->t_dfops.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Now that all callers use ->t_dfops, the xfs_bmapi_write() dfops
parameter is no longer necessary. Remove it and access ->t_dfops
directly. This patch does not change behavior.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_dquot_disk_alloc() receives a transaction from the caller and
passes a local dfops along to xfs_bmapi_write(). If we attach this
dfops to the transaction, we have to make sure to clear it before
returning to avoid invalid access of stack memory.
Since xfs_qm_dqread_alloc() is the only caller, pull dfops into the
caller and attach it to the transaction to eliminate this pattern
entirely.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Remove the verbose license text from XFS files and replace them
with SPDX tags. This does not change the license of any of the code,
merely refers to the common, up-to-date license files in LICENSES/
This change was mostly scripted. fs/xfs/Makefile and
fs/xfs/libxfs/xfs_fs.h were modified by hand, the rest were detected
and modified by the following command:
for f in `git grep -l "GNU General" fs/xfs/` ; do
echo $f
cat $f | awk -f hdr.awk > $f.new
mv -f $f.new $f
done
And the hdr.awk script that did the modification (including
detecting the difference between GPL-2.0 and GPL-2.0+ licenses)
is as follows:
$ cat hdr.awk
BEGIN {
hdr = 1.0
tag = "GPL-2.0"
str = ""
}
/^ \* This program is free software/ {
hdr = 2.0;
next
}
/any later version./ {
tag = "GPL-2.0+"
next
}
/^ \*\// {
if (hdr > 0.0) {
print "// SPDX-License-Identifier: " tag
print str
print $0
str=""
hdr = 0.0
next
}
print $0
next
}
/^ \* / {
if (hdr > 1.0)
next
if (hdr > 0.0) {
if (str != "")
str = str "\n"
str = str $0
next
}
print $0
next
}
/^ \*/ {
if (hdr > 0.0)
next
print $0
next
}
// {
if (hdr > 0.0) {
if (str != "")
str = str "\n"
str = str $0
next
}
print $0
}
END { }
$
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Create a helper function to iterate all the dquots of a given type in
the system, and refactor the dquot scrub to use it. This will get more
use in the quota repair code.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
DQALLOC is only ever used with xfs_qm_dqget*, and the only flag that the
_dqget family of functions cares about is DQALLOC. Therefore, change
it to a boolean 'can alloc?' flag for the dqget interfaces where that
makes sense.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
The quota initialization code needs an "uncached" variant of _dqget to
read in default quota limits and timers before the dquot cache is fully
set up. We've already split up _dqget into its component pieces so
create a fourth variant to address this need, and make dqread internal
to xfs_dquot.c again.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Separate the disk dquot read and allocation functionality into
two helper functions, then refactor dqread to call them directly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Create two incore dquot initialization functions that will help us to
disentangle dqget and dqread.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
There are two uses of dqget here -- one is to return the dquot for a
given type and id, and the other is to return the dquot for a given type
and inode. Those are two separate things, so split them into two
smaller functions.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the dqget input checks to a separate function in preparation for
splitting up the dqget functionality.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Delegate the dquot cache handling (radix tree lookup and insertion) to
separate helper functions so that we can continue to simplify the body
of dqget.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
There's only one caller of DQNEXT and its semantics can be moved into a
separate function, so create the function and get rid of the flag.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In commit efa092f3d4 "[XFS] Fixes a bug in the quota code when
allocating a new dquot record", we allocate a new dquot block, grab a
buffer to initialize it, and return the locked initialized dquot buffer
to the caller for further in-core dquot initialization. Unfortunately,
if the _bmap_finish errored out, _qm_dqalloc would also error out
without bothering to free the (locked) buffer. Leaking a locked buffer
caused hangs in generic/388 when quotas are enabled.
Furthermore, the _bmap_finish -> _defer_finish conversion in
310a75a3c6 ("xfs: change xfs_bmap_{finish,cancel,init,free} ->
xfs_defer_*") failed to observe that the buffer was held going into
_defer_finish and therefore failed to notice that the buffer lock is
/not/ maintained afterwards. Now that we can bjoin a buffer to a
defer_ops, use this mechanism to ensure that the buffer stays locked
across the _defer_finish. Release the holds and locks on the buffer as
appropriate if we have to error out.
There is a subtlety here for the caller in that the buffer emerges
locked and held to the transaction, so if the _trans_commit fails we
have to release the buffer explicitly. This fixes the unmount hang
in generic/388 when quotas are enabled.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
The log item flags contain a field that is protected by the AIL
lock - the XFS_LI_IN_AIL flag. We use non-atomic RMW operations to
set and clear these flags, but most of the updates and checks are
not done with the AIL lock held and so are susceptible to update
races.
Fix this by changing the log item flags to use atomic bitops rather
than be reliant on the AIL lock for update serialisation.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Add an xfs_dqblk verifier so that it can check the uuid on V5 filesystems;
it calls the existing xfs_dquot_verify verifier to validate the
xfs_disk_dquot_t contained inside it. This lets us move the uuid
verification out of the crc verifier, which makes little sense.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Long ago the flags argument was used to determine whether to issue warnings
about corruptions, but that's done elsewhere now and the flag is unused
here, so remove it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This is a simple rename, except that xa_ail becomes ail_head.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
In xfs_qm_dqalloc, we join the locked quota inode to the transaction we
use to allocate blocks. If the allocation or mapping fails, we're not
allowed to unlock the inode because the transaction code is in charge of
unlocking it for us. Therefore, remove the iunlock call to avoid
blowing asserts about unbalanced locking + mount hang.
Found by corrupting the AGF and allocating space in the filesystem
(quotacheck) immediately after mount. The upcoming agfl wrapping fixup
test will trigger this scenario.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Rename xfs_dqcheck to xfs_dquot_verify and make it return an
xfs_failaddr_t like every other structure verifier function.
This enables us to check on-disk quotas in the same way that we check
everything else. Callers are now responsible for logging errors, as
XFS_QMOPT_DOWARN goes away.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Move the dquot repair code into a separate function and remove
XFS_QMOPT_DQREPAIR in favor of calling the helper directly. Remove
other dead code because quotacheck is the only caller of DQREPAIR.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Once the inode item writeback errors is already fixed, it's time to fix the same
problem in dquot code.
Although there were no reports of users hitting this bug in dquot code (at least
none I've seen), the bug is there and I was already planning to fix it when the
correct approach to fix the inodes part was decided.
This patch aims to fix the same problem in dquot code, regarding failed buffers
being unable to be resubmitted once they are flush locked.
Tested with the recently test-case sent to fstests list by Hou Tao.
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Add a new xfs_iext_cursor structure to hide the direct extent map
index manipulations. In addition to the existing lookup/get/insert/
remove and update routines new primitives to get the first and last
extent cursor, as well as moving up and down by one extent are
provided. Also new are convenience to increment/decrement the
cursor and retreive the new extent, as well as to peek into the
previous/next extent without updating the cursor and last but not
least a macro to iterate over all extents in a fork.
[darrick: rename for_each_iext to for_each_xfs_iext]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
And instead require callers to explicitly join the inode using
xfs_defer_ijoin. Also consolidate the defer error handling in
a few places using a goto label.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This reverts commit 50e0bdbe9f.
The new XFS_QMOPT_NOLOCK isn't used at all, and conditional locking based
on a flag is always the wrong thing to do - we should be having helpers
that can be called without the lock instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The patch below updated xfs_dq_get_next_id() to use the XFS iext
lookup helpers to locate the next quota id rather than to seek for
data in the quota file. The updated code fails to correctly handle
the case where the quota inode might have contiguous chunks part of
the same extent. In this case, the start block offset is calculated
based on the next expected id but the extent lookup returns the same
start offset as for the previous chunk. This causes the returned id
to go backwards and livelocks the quota iteration. This problem is
reproduced intermittently by generic/232.
To handle this case, check whether the startoff from the extent
lookup is behind the startoff calculated from the next quota id. If
so, bump up got.br_startoff to the specific file offset that is
expected to hold the next dquot chunk.
Fixes: bda250dbaf ("xfs: rewrite xfs_dq_get_next_id using xfs_iext_lookup_extent")
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This goes straight to a single lookup in the extent list and avoids a
roundtrip through two layers that don't add any value for the simple
quoata file that just has data or holes and no page cache, delayed
allocation, unwritten extent or COW fork (which btw, doesn't seem to
be handled by the existing SEEK HOLE/DATA code).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Add a new dqget flag that grabs the dquot without taking the ilock.
This will be used by the scrubber (which will have already grabbed
the ilock) to perform basic sanity checking of the quota data.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
This is a purely mechanical patch that removes the private
__{u,}int{8,16,32,64}_t typedefs in favor of using the system
{u,}int{8,16,32,64}_t typedefs. This is the sed script used to perform
the transformation and fix the resulting whitespace and indentation
errors:
s/typedef\t__uint8_t/typedef __uint8_t\t/g
s/typedef\t__uint/typedef __uint/g
s/typedef\t__int\([0-9]*\)_t/typedef int\1_t\t/g
s/__uint8_t\t/__uint8_t\t\t/g
s/__uint/uint/g
s/__int\([0-9]*\)_t\t/__int\1_t\t\t/g
s/__int/int/g
/^typedef.*int[0-9]*_t;$/d
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The GETNEXTQOTA ioctl takes whatever ID is sent in,
and looks for the next active quota for an user
equal or higher to that ID.
But if we are at the maximum ID and then ask for the "next"
one, we may wrap back to zero. In this case, userspace
may loop forever, because it will start querying again
at zero.
We'll fix this in userspace as well, but for the kernel,
return -ENOENT if we ask for the next quota ID
past UINT_MAX so the caller knows to stop.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Mechanical change of flist/free_list to dfops, since they're now
deferred ops, not just a freeing list.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Drop the compatibility shims that we were using to integrate the new
deferred operation mechanism into the existing code. No new code.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Restructure everything that used xfs_bmap_free to use xfs_defer_ops
instead. For now we'll just remove the old symbols and play some
cpp magic to make it work; in the next patch we'll actually rename
everything.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
One of the problems we currently have with delayed logging is that
under serious memory pressure we can deadlock memory reclaim. THis
occurs when memory reclaim (such as run by kswapd) is reclaiming XFS
inodes and issues a log force to unpin inodes that are dirty in the
CIL.
The CIL is pushed, but this will only occur once it gets the CIL
context lock to ensure that all committing transactions are complete
and no new transactions start being committed to the CIL while the
push switches to a new context.
The deadlock occurs when the CIL context lock is held by a
committing process that is doing memory allocation for log vector
buffers, and that allocation is then blocked on memory reclaim
making progress. Memory reclaim, however, is blocked waiting for
a log force to make progress, and so we effectively deadlock at this
point.
To solve this problem, we have to move the CIL log vector buffer
allocation outside of the context lock so that memory reclaim can
always make progress when it needs to force the log. The problem
with doing this is that a CIL push can take place while we are
determining if we need to allocate a new log vector buffer for
an item and hence the current log vector may go away without
warning. That means we canot rely on the existing log vector being
present when we finally grab the context lock and so we must have a
replacement buffer ready to go at all times.
To ensure this, introduce a "shadow log vector" buffer that is
always guaranteed to be present when we gain the CIL context lock
and format the item. This shadow buffer may or may not be used
during the formatting, but if the log item does not have an existing
log vector buffer or that buffer is too small for the new
modifications, we swap it for the new shadow buffer and format
the modifications into that new log vector buffer.
The result of this is that for any object we modify more than once
in a given CIL checkpoint, we double the memory required
to track dirty regions in the log. For single modifications then
we consume the shadow log vectorwe allocate on commit, and that gets
consumed by the checkpoint. However, if we make multiple
modifications, then the second transaction commit will allocate a
shadow log vector and hence we will end up with double the memory
usage as only one of the log vectors is consumed by the CIL
checkpoint. The remaining shadow vector will be freed when th elog
item is freed.
This can probably be optimised in future - access to the shadow log
vector is serialised by the object lock (as opposited to the active
log vector, which is controlled by the CIL context lock) and so we
can probably free shadow log vector from some objects when the log
item is marked clean on removal from the AIL.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
These three warnings are fixed:
fs/xfs/xfs_inode.c:1033:44: warning: Using plain integer as NULL pointer
fs/xfs/xfs_inode_item.c:525:20: warning: context imbalance in 'xfs_inode_item_push' - unexpected unlock
fs/xfs/xfs_dquot.c:696:1: warning: symbol 'xfs_dq_get_next_id' was not declared. Should it be static?
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Merge xfs_trans_reserve and xfs_trans_alloc into a single function call
that returns a transaction with all the required log and block reservations,
and which allows passing transaction flags directly to avoid the cumbersome
_xfs_trans_alloc interface.
While we're at it we also get rid of the transaction type argument that has
been superflous since we stopped supporting the non-CIL logging mode. The
guts of it will be removed in another patch.
[dchinner: fixed transaction leak in error path in xfs_setattr_nonsize]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Default quotas are globally set due historical reasons. IRIX only
supported user and project quotas, and default quota was only
applied to user quotas.
In Linux, when a default quota is set, all different quota types
inherits the same default value.
An user with a quota limit larger than the default quota value, will
still be limited to the default value because the group quotas also
inherits the default quotas. Unless the group which the user belongs
to have a custom quota limit set.
This patch aims to split the default quota value by quota type.
Allowing each quota type having different default values.
Default time limits are still set globally. XFS does not set a
per-user/group timer, but a single global timer. For changing this
behavior, some changes should be made in user-space tools another
bugs being fixed.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Add code to allow the Q_XGETNEXTQUOTA quotactl to quickly find
all active quotas by examining the quota inode, and skipping
over unallocated or uninitialized regions.
Userspace can then use this interface rather than i.e. a
getpwent() loop when asked to report all active quotas.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Allow us to get the appropriate quota inode from any
mp & quota flags, not necessarily associated with a
particular dqp. Needed for when we are searching for
the next active ID with quotas and we want to examine
the quota inode.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Quota IDs are unsigned, and so we can pass in values up
to 2^32-1. But if we try to initialize a block containing
values over MAX_INT, curid will overflow and assert.
curid holds a quota ID, so give it the proper
xfs_dqid_t type (and remove the now-impossible ASSERT).
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Calls to xfs_bmap_finish() and xfs_trans_ijoin(), and the
associated comments were replicated several times across
the attribute code, all dealing with what to do if the
transaction was or wasn't committed.
And in that replicated code, an ASSERT() test of an
uninitialized variable occurs in several locations:
error = xfs_attr_thing(&args);
if (!error) {
error = xfs_bmap_finish(&args.trans, args.flist,
&committed);
}
if (error) {
ASSERT(committed);
If the first xfs_attr_thing() failed, we'd skip the xfs_bmap_finish,
never set "committed", and then test it in the ASSERT.
Fix this up by moving the committed state internal to xfs_bmap_finish,
and add a new inode argument. If an inode is passed in, it is passed
through to __xfs_trans_roll() and joined to the transaction there if
the transaction was committed.
xfs_qm_dqalloc() was a little unique in that it called bjoin rather
than ijoin, but as Dave points out we can detect the committed state
but checking whether (*tpp != tp).
Addresses-Coverity-Id: 102360
Addresses-Coverity-Id: 102361
Addresses-Coverity-Id: 102363
Addresses-Coverity-Id: 102364
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This patch modifies the stats counting macros and the callers
to those macros to properly increment, decrement, and add-to
the xfs stats counts. The counts for global and per-fs stats
are correctly advanced, and cleared by writing a "1" to the
corresponding clear file.
global counts: /sys/fs/xfs/stats/stats
per-fs counts: /sys/fs/xfs/sda*/stats/stats
global clear: /sys/fs/xfs/stats/stats_clear
per-fs clear: /sys/fs/xfs/sda*/stats/stats_clear
[dchinner: cleaned up macro variables, removed CONFIG_FS_PROC around
stats structures and macros. ]
Signed-off-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Once the sb_uuid is changed, the wrong uuid is stamped into new
dquots on disk. Found by inspection, verified by generic/219.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Several areas of code duplicate a pattern where we take the AIL lock,
check whether an item is in the AIL and remove it if so. Create a new
helper for this pattern and use it where appropriate.
Signed-off-by: Brian Foster <bfoster@redhat.com>
The flags argument to xfs_trans_commit is not useful for most callers, as
a commit of a transaction without a permanent log reservation must pass
0 here, and all callers for a transaction with a permanent log reservation
except for xfs_trans_roll must pass XFS_TRANS_RELEASE_LOG_RES. So remove
the flags argument from the public xfs_trans_commit interfaces, and
introduce low-level __xfs_trans_commit variant just for xfs_trans_roll
that regrants a log reservation instead of releasing it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
xfs_trans_cancel takes two flags arguments: XFS_TRANS_RELEASE_LOG_RES and
XFS_TRANS_ABORT. Both of them are a direct product of the transaction
state, and can be deducted:
- any dirty transaction needs XFS_TRANS_ABORT to be properly canceled,
and XFS_TRANS_ABORT is a noop for a transaction that is not dirty.
- any transaction with a permanent log reservation needs
XFS_TRANS_RELEASE_LOG_RES to be properly canceled, and passing
XFS_TRANS_RELEASE_LOG_RES for a transaction without a permanent
log reservation is invalid.
So just remove the flags argument and do the right thing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
More on-disk format consolidation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
More on-disk format consolidation. A few declarations that weren't on-disk
format related move into better suitable spots.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
When running xfs/305, I noticed that quotacheck was flushing dquot
buffers that did not have the xfs_dquot_buf_ops verifiers attached:
XFS (vdb): _xfs_buf_ioapply: no ops on block 0x1dc8/0x1dc8
ffff880052489000: 44 51 01 04 00 00 65 b8 00 00 00 00 00 00 00 00 DQ....e.........
ffff880052489010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
ffff880052489020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
ffff880052489030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
CPU: 1 PID: 2376 Comm: mount Not tainted 3.16.0-rc2-dgc+ #306
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffff88006fe38000 ffff88004a0ffae8 ffffffff81cf1cca 0000000000000001
ffff88004a0ffb88 ffffffff814d50ca 000010004a0ffc70 0000000000000000
ffff88006be56dc4 0000000000000021 0000000000001dc8 ffff88007c773d80
Call Trace:
[<ffffffff81cf1cca>] dump_stack+0x45/0x56
[<ffffffff814d50ca>] _xfs_buf_ioapply+0x3ca/0x3d0
[<ffffffff810db520>] ? wake_up_state+0x20/0x20
[<ffffffff814d51f5>] ? xfs_bdstrat_cb+0x55/0xb0
[<ffffffff814d513b>] xfs_buf_iorequest+0x6b/0xd0
[<ffffffff814d51f5>] xfs_bdstrat_cb+0x55/0xb0
[<ffffffff814d53ab>] __xfs_buf_delwri_submit+0x15b/0x220
[<ffffffff814d6040>] ? xfs_buf_delwri_submit+0x30/0x90
[<ffffffff814d6040>] xfs_buf_delwri_submit+0x30/0x90
[<ffffffff8150f89d>] xfs_qm_quotacheck+0x17d/0x3c0
[<ffffffff81510591>] xfs_qm_mount_quotas+0x151/0x1e0
[<ffffffff814ed01c>] xfs_mountfs+0x56c/0x7d0
[<ffffffff814f0f12>] xfs_fs_fill_super+0x2c2/0x340
[<ffffffff811c9fe4>] mount_bdev+0x194/0x1d0
[<ffffffff814f0c50>] ? xfs_finish_flags+0x170/0x170
[<ffffffff814ef0f5>] xfs_fs_mount+0x15/0x20
[<ffffffff811ca8c9>] mount_fs+0x39/0x1b0
[<ffffffff811e4d67>] vfs_kern_mount+0x67/0x120
[<ffffffff811e757e>] do_mount+0x23e/0xad0
[<ffffffff8117abde>] ? __get_free_pages+0xe/0x50
[<ffffffff811e71e6>] ? copy_mount_options+0x36/0x150
[<ffffffff811e8103>] SyS_mount+0x83/0xc0
[<ffffffff81cfd40b>] tracesys+0xdd/0xe2
This was caused by dquot buffer readahead not attaching a verifier
structure to the buffer when readahead was issued, resulting in the
followup read of the buffer finding a valid buffer and so not
attaching new verifiers to the buffer as part of the read.
Also, when a verifier failure occurs, we then read the buffer
without verifiers. Attach the verifiers manually after this read so
that if the buffer is then written it will be verified that the
corruption has been repaired.
Further, when flushing a dquot we don't ask for a verifier when
reading in the dquot buffer the dquot belongs to. Most of the time
this isn't an issue because the buffer is still cached, but when it
is not cached it will result in writing the dquot buffer without
having the verfier attached.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Convert all the errors the core XFs code to negative error signs
like the rest of the kernel and remove all the sign conversion we
do in the interface layers.
Errors for conversion (and comparison) found via searches like:
$ git grep " E" fs/xfs
$ git grep "return E" fs/xfs
$ git grep " E[A-Z].*;$" fs/xfs
Negation points found via searches like:
$ git grep "= -[a-z,A-Z]" fs/xfs
$ git grep "return -[a-z,A-D,F-Z]" fs/xfs
$ git grep " -[a-z].*;" fs/xfs
[ with some bits I missed from Brian Foster ]
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
XFS_ERROR was designed long ago to trap return values, but it's not
runtime configurable, it's not consistently used, and we can do
similar error trapping with ftrace scripts and triggers from
userspace.
Just nuke XFS_ERROR and associated bits.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
return is not a function. "return(EIO);" is silly;
"return (EIO);" moreso. return is not a function.
Nuke the pointless parens.
[dchinner: catch a couple of extra cases in xfs_attr_list.c,
xfs_acl.c and xfs_linux.h.]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Most of the callers are just calling ASSERT(!xfs_buf_geterror())
which means they are checking for bp->b_error == 0. If bp is null in
this case, we will assert fail, and hence it's no different in
result to oopsing because of a null bp. In some cases, errors have
already been checked for or the function returning the buffer can't
return a buffer with an error, so it's just a redundant assert.
Either way, the assert can either be removed.
The other two non-assert callers can just test for a buffer and
error properly.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
group and project quota hints are currently stored on the user
dquot. If we are attaching quotas to the inode, then the group and
project dquots are stored as hints on the user dquot to save having
to look them up again later.
The thing is, the hints are not used for that inode for the rest of
the life of the inode - the dquots are attached directly to the
inode itself - so the only time the hints are used is when an inode
first has dquots attached.
When the hints on the user dquot don't match the dquots being
attache dto the inode, they are then removed and replaced with the
new hints. If a user is concurrently modifying files in different
group and/or project contexts, then this leads to thrashing of the
hints attached to user dquot.
If user quotas are not enabled, then hints are never even used.
So, if the hints are used to avoid the cost of the lookup, is the
cost of the lookup significant enough to justify the hint
infrstructure? Maybe it was once, when there was a global quota
manager shared between all XFS filesystems and was hash table based.
However, lookups are now much simpler, requiring only a single lock and
radix tree lookup local to the filesystem and no hash or LRU
manipulations to be made. Hence the cost of lookup is much lower
than when hints were implemented. Turns out that benchmarks show
that, too, with thir being no differnce in performance when doing
file creation workloads as a single user with user, group and
project quotas enabled - the hints do not make the code go any
faster. In fact, removing the hints shows a 2-3% reduction in the
time it takes to create 50 million inodes....
So, let's just get rid of the hints and the complexity around them.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The dquot allocation path in xfs_qm_dqread() currently uses the
attribute set log reservation, which appears to be incorrect. We
have reports of transaction reservation overruns with the current
code. E.g., a repeated run of xfstests test generic/270 on a 512b
block size fs occassionally produces the following in dmesg:
XFS (sdN): xlog_write: reservation summary:
trans type = QM_DQALLOC (30)
unit res = 7080 bytes
current res = -632 bytes
total reg = 0 bytes (o/flow = 0 bytes)
ophdrs = 0 (ophdr space = 0 bytes)
ophdr + reg = 0 bytes
num regions = 0
XFS (sdN): xlog_write: reservation ran out. Need to up reservation
The dquot allocation case should consist of a write reservation
(i.e., we are allocating a range of the internal quota file) plus
the size of the actual dquots. We already have a log reservation
definition for this operation (tr_qm_dqalloc). Use it in
xfs_qm_dqread() and update the log reservation calculation function
to use the write res. calculation function rather than reading the
assumed to be pre-calculated value directly.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We might not have read in the extent list at this point, so make sure we
take the ilock exclusively if we have to do so.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Currently the xfs_inode.h header has a dependency on the definition
of the BMAP btree records as the inode fork includes an array of
xfs_bmbt_rec_host_t objects in it's definition.
Move all the btree format definitions from xfs_btree.h,
xfs_bmap_btree.h, xfs_alloc_btree.h and xfs_ialloc_btree.h to
xfs_format.h to continue the process of centralising the on-disk
format definitions. With this done, the xfs inode definitions are no
longer dependent on btree header files.
The enables a massive culling of unnecessary includes, with close to
200 #include directives removed from the XFS kernel code base.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
xfs_trans.h has a dependency on xfs_log.h for a couple of
structures. Most code that does transactions doesn't need to know
anything about the log, but this dependency means that they have to
include xfs_log.h. Decouple the xfs_trans.h and xfs_log.h header
files and clean up the includes to be in dependency order.
In doing this, remove the direct include of xfs_trans_reserve.h from
xfs_trans.h so that we remove the dependency between xfs_trans.h and
xfs_mount.h. Hence the xfs_trans.h include can be moved to the
indicate the actual dependencies other header files have on it.
Note that these are kernel only header files, so this does not
translate to any userspace changes at all.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Parts of userspace want to be able to read and modify dquot buffers
(e.g. xfs_db) so we need to split out the reading and writing of
these buffers so it is easy to shared code with libxfs in userspace.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
All of the buffer operations structures are needed to be exported
for xfs_db, so move them all to a common location rather than
spreading them all over the place. They are verifying the on-disk
format, so while xfs_format.h might be a good place, it is not part
of the on disk format.
Hence we need to create a new header file that we centralise these
related definitions. Start by moving the bffer operations
structures, and then also move all the other definitions that have
crept into xfs_log_format.h and xfs_format.h as there was no other
shared header file to put them in.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
Michael Semon reported that xfs/299 generated this lockdep warning:
=============================================
[ INFO: possible recursive locking detected ]
3.12.0-rc2+ #2 Not tainted
---------------------------------------------
touch/21072 is trying to acquire lock:
(&xfs_dquot_other_class){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64
but task is already holding lock:
(&xfs_dquot_other_class){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&xfs_dquot_other_class);
lock(&xfs_dquot_other_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by touch/21072:
#0: (sb_writers#10){++++.+}, at: [<c11185b6>] mnt_want_write+0x1e/0x3e
#1: (&type->i_mutex_dir_key#4){+.+.+.}, at: [<c11078ee>] do_last+0x245/0xe40
#2: (sb_internal#2){++++.+}, at: [<c122c9e0>] xfs_trans_alloc+0x1f/0x35
#3: (&(&ip->i_lock)->mr_lock/1){+.+...}, at: [<c126cd1b>] xfs_ilock+0x100/0x1f1
#4: (&(&ip->i_lock)->mr_lock){++++-.}, at: [<c126cf52>] xfs_ilock_nowait+0x105/0x22f
#5: (&dqp->q_qlock){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64
#6: (&xfs_dquot_other_class){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64
The lockdep annotation for dquot lock nesting only understands
locking for user and "other" dquots, not user, group and quota
dquots. Fix the annotations to match the locking heirarchy we now
have.
Reported-by: Michael L. Semon <mlsemon35@gmail.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Convert the XFS dquot lru to use the list_lru construct and convert the
shrinker to being node aware.
[glommer@openvz.org: edited for conflicts + warning fixes]
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Glauber Costa <glommer@openvz.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Carlos Maiolino <cmaiolino@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Rientjes <rientjes@google.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: J. Bruce Fields <bfields@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
With the new xfs_trans_res structure has been introduced, the log
reservation size, log count as well as log flags are pre-initialized
at mount time. So it's time to refine xfs_trans_reserve() interface
to be more neat.
Also, introduce a new helper M_RES() to return a pointer to the
mp->m_resv structure to simplify the input.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
There is a bunch of code in xfs_bmap.c that is kernel specific and
not shared with userspace. To minimise the difference between the
kernel and userspace code, shift this unshared code to
xfs_bmap_util.c, and the declarations to xfs_bmap_util.h.
The biggest issue here is xfs_bmap_finish() - userspace has it's own
definition of this function, and so we need to move it out of
xfs_bmap.[ch]. This means several other files need to include
xfs_bmap_util.h as well.
It also introduces and interesting dance for the stack switching
code in xfs_bmapi_allocate(). The stack switching/workqueue code is
actually moved to xfs_bmap_util.c, so that userspace can simply use
a #define in a header file to connect the dots without needing to
know about the stack switch code at all.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The on disk format definitions of the on-disk dquot, log formats and
quota off log formats are all intertwined with other definitions for
quotas. Separate them out into their own header file so they can
easily be shared with userspace.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Add project quota changes to all the places where group quota field
is used:
* add separate project quota members into various structures
* split project quota and group quotas so that instead of overriding
the group quota members incore, the new project quota members are
used instead
* get rid of usage of the OQUOTA flag incore, in favor of separate
group and project quota flags.
* add a project dquot argument to various functions.
Not using the pquotino field from superblock yet.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
In preparation for combined pquota/gquota support, for the sake
of readability, do some code cleanup surrounding the affected
code.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
In preparation for combined pquota/gquota support, for the sake
of readability, change the macro to an inline function.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
In preparation for combined pquota/gquota support, for the sake
of readability, change the macro to an inline function.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Calculating dquot CRCs when the backing buffer is written back just
doesn't work reliably. There are several places which manipulate
dquots directly in the buffers, and they don't calculate CRCs
appropriately, nor do they always set the buffer up to calculate
CRCs appropriately.
Firstly, if we log a dquot buffer (e.g. during allocation) it gets
logged without valid CRC, and so on recovery we end up with a dquot
that is not valid.
Secondly, if we recover/repair a dquot, we don't have a verifier
attached to the buffer and hence CRCs are not calculated on the way
down to disk.
Thirdly, calculating the CRC after we've changed the contents means
that if we re-read the dquot from the buffer, we cannot verify the
contents of the dquot are valid, as the CRC is invalid.
So, to avoid all the dquot CRC errors that are being detected by the
read verifier, change to using the same model as for inodes. That
is, dquot CRCs are calculated and written to the backing buffer at
the time the dquot is flushed to the backing buffer. If we modify
the dquot directly in the backing buffer, calculate the CRC
immediately after the modification is complete. Hence the dquot in
the on-disk buffer should always have a valid CRC.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Use the reserved space in struct xfs_dqblk to store a UUID and a crc
for the quota blocks.
[dchinner@redhat.com] Add a LSN field and update for current verifier
infrastructure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Enable tracking of high and low watermarks for preallocation
throttling of files under quota restrictions. These values are
calculated when the quota limit is read from disk or modified and
cached for later use by the throttling algorithm.
The high watermark specifies when preallocation is disabled, the
low watermark specifies when throttling is enabled and the low free
space data structure contains precalculated low free space limits
to serve as input to determine the level of throttling required.
Note that the low free space data structure is based on the
existing global low free space data structure with the exception of
using three stages (5%, 3% and 1%) rather than five to reduce the
impact of xfs_dquot memory overhead.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Modify xfs_qm_adjust_dqlimits() to take the xfs_dquot as a
parameter instead of just the xfs_disk_dquot_t so we can update
in-memory fields if necessary.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The disk quota allocation log space reservation is calcuated at runtime,
this patch does it at mount time.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
CC: Dave Chinner <david@fromorbit.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
To separate the verifiers from iodone functions and associate read
and write verifiers at the same time, introduce a buffer verifier
operations structure to the xfs_buf.
This avoids the need for assigning the write verifier, clearing the
iodone function and re-running ioend processing in the read
verifier, and gets rid of the nasty "b_pre_io" name for the write
verifier function pointer. If we ever need to, it will also be
easier to add further content specific callbacks to a buffer with an
ops structure in place.
We also avoid needing to export verifier functions, instead we
can simply export the ops structures for those that are needed
outside the function they are defined in.
This patch also fixes a directory block readahead verifier issue
it exposed.
This patch also adds ops callbacks to the inode/alloc btree blocks
initialised by growfs. These will need more work before they will
work with CRCs.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Phil White <pwhite@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Metadata buffers that are read from disk have write verifiers
already attached to them, but newly allocated buffers do not. Add
appropriate write verifiers to all new metadata buffers.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
These verifiers are essentially the same code as the read verifiers,
but do not require ioend processing. Hence factor the read verifier
functions and add a new write verifier wrapper that is used as the
callback.
This is done as one large patch for all verifiers rather than one
patch per verifier as the change is largely mechanical. This
includes hooking up the write verifier via the read verifier
function.
Hooking up the write verifier for buffers obtained via
xfs_trans_get_buf() will be done in a separate patch as that touches
code in many different places rather than just the verifier
functions.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Add a dquot buffer verify callback function and pass it into the
buffer read functions. This checks all the dquots in a buffer, but
cannot completely verify the dquot ids are correct. Also, errors
cannot be repaired, so an additional function is added to repair bad
dquots in the buffer if such an error is detected in a context where
repair is allowed.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Phil White <pwhite@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Add a verifier function callback capability to the buffer read
interfaces. This will be used by the callers to supply a function
that verifies the contents of the buffer when it is read from disk.
This patch does not provide callback functions, but simply modifies
the interfaces to allow them to be called.
The reason for adding this to the read interfaces is that it is very
difficult to tell fom the outside is a buffer was just read from
disk or whether we just pulled it out of cache. Supplying a callbck
allows the buffer cache to use it's internal knowledge of the buffer
to execute it only when the buffer is read from disk.
It is intended that the verifier functions will mark the buffer with
an EFSCORRUPTED error when verification fails. This allows the
reading context to distinguish a verification error from an IO
error, and potentially take further actions on the buffer (e.g.
attempt repair) based on the error reported.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Phil White <pwhite@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Untangle the header file includes a bit by moving the definition of
xfs_agino_t to xfs_types.h. This removes the dependency that xfs_ag.h has on
xfs_inum.h, meaning we don't need to include xfs_inum.h everywhere we include
xfs_ag.h.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
xfs_trans_ail_delete_bulk() can be called from different contexts so
if the item is not in the AIL we need different shutdown for each
context. Pass in the shutdown method needed so the correct action
can be taken.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Queue delwri buffers on a local on-stack list instead of a per-buftarg one,
and write back the buffers per-process instead of by waking up xfsbufd.
This is now easily doable given that we have very few places left that write
delwri buffers:
- log recovery:
Only done at mount time, and already forcing out the buffers
synchronously using xfs_flush_buftarg
- quotacheck:
Same story.
- dquot reclaim:
Writes out dirty dquots on the LRU under memory pressure. We might
want to look into doing more of this via xfsaild, but it's already
more optimal than the synchronous inode reclaim that writes each
buffer synchronously.
- xfsaild:
This is the main beneficiary of the change. By keeping a local list
of buffers to write we reduce latency of writing out buffers, and
more importably we can remove all the delwri list promotions which
were hitting the buffer cache hard under sustained metadata loads.
The implementation is very straight forward - xfs_buf_delwri_queue now gets
a new list_head pointer that it adds the delwri buffers to, and all callers
need to eventually submit the list using xfs_buf_delwi_submit or
xfs_buf_delwi_submit_nowait. Buffers that already are on a delwri list are
skipped in xfs_buf_delwri_queue, assuming they already are on another delwri
list. The biggest change to pass down the buffer list was done to the AIL
pushing. Now that we operate on buffers the trylock, push and pushbuf log
item methods are merged into a single push routine, which tries to lock the
item, and if possible add the buffer that needs writeback to the buffer list.
This leads to much simpler code than the previous split but requires the
individual IOP_PUSH instances to unlock and reacquire the AIL around calls
to blocking routines.
Given that xfsailds now also handle writing out buffers, the conditions for
log forcing and the sleep times needed some small changes. The most
important one is that we consider an AIL busy as long we still have buffers
to push, and the other one is that we do increment the pushed LSN for
buffers that are under flushing at this moment, but still count them towards
the stuck items for restart purposes. Without this we could hammer on stuck
items without ever forcing the log and not make progress under heavy random
delete workloads on fast flash storage devices.
[ Dave Chinner:
- rebase on previous patches.
- improved comments for XBF_DELWRI_Q handling
- fix XBF_ASYNC handling in queue submission (test 106 failure)
- rename delwri submit function buffer list parameters for clarity
- xfs_efd_item_push() should return XFS_ITEM_PINNED ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Instead of writing the buffer directly from inside xfs_qm_dqflush return it
to the caller and let the caller decide what to do with the buffer. Also
remove the pincount check in xfs_qm_dqflush that all non-blocking callers
already implement and the now unused flags parameter and the XFS_DQ_IS_DIRTY
check that all callers already perform.
[ Dave Chinner: fixed build error cause by missing '{'. ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
If a filesystem has been forced shutdown we are never going to write inodes
to disk, which means the inode items will stay in the AIL until we free
the inode. Currently that is not a problem, but a pending change requires us
to empty the AIL before shutting down the filesystem. In that case leaving
the inode in the AIL is lethal. Make sure to remove the log item from the AIL
to allow emptying the AIL on shutdown filesystems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
If a filesystem has been forced shutdown we are never going to write dquots
to disk, which means the dquot items will stay in the AIL forever.
Currently that is not a problem, but a pending chance requires us to
empty the AIL before shutting down the filesystem, in which case this
behaviour is lethal. Make sure to remove the log item from the AIL
to allow emptying the AIL on shutdown filesystems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Eric Sandeen