Current HSPI driver is using msleep(20) on hspi_status_check_timeout(),
but it was too long delay for SPI device.
Bock-W board SPI access was too slow without this patch.
This patch uses udelay(10) for it.
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to its documentation, clk_get() returns a "valid IS_ERR() condition
containing errno", so we should call IS_ERR() rather than a NULL check.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The current HSPI driver used automatic CS control, leading to CS
active for each byte transmitted. This patch changes the driver
to manual CS control, and ensures CS is active thoughout a whole
message. Additionally, it uses the cs_change field to determine
if CS is disabled between transfers in the message.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
devm free functions should not have to be explicitly used.
A semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
(
* devm_kfree(...);
|
* devm_free_irq(...);
|
* devm_iounmap(...);
|
* devm_release_region(...);
|
* devm_release_mem_region(...);
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current sh-hspi had wrong write/read method which was not linux standard.
If spi_transfer requests tx[2], rx[2] len=2,
then, driver should run tx[0], rx[0], tx[1], rx[1].
But current sh-hspi runs tx[0], tx[1], rx[0], rx[1].
This patch fixes it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Current sh-hspi had used platform-specific speed.
This patch remove it, and use spi_transfer specific speed.
It removes unnecessary flags from struct sh_hspi_info,
but struct sh_hspi_info is still exist, since sh-hspi needs
platform info in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds SuperH HSPI driver.
It is still prototype driver, but has enough function at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Kuninori Morimoto