It is not clear from documenting comments, specifications, or code
usage what value the gss_krb5_enctype.blocksize field is supposed
to store. The "encryption blocksize" depends only on the cipher
being used, so that value can be derived where it's needed instead
of stored as a constant.
RFC 3961 Section 5.2 says:
> cipher block size, c
> This is the block size of the block cipher underlying the
> encryption and decryption functions indicated above, used for key
> derivation and for the size of the message confounder and initial
> vector. (If a block cipher is not in use, some comparable
> parameter should be determined.) It must be at least 5 octets.
>
> This is not actually an independent parameter; rather, it is a
> property of the functions E and D. It is listed here to clarify
> the distinction between it and the message block size, m.
In the Linux kernel's implemenation of the SunRPC RPCSEC GSS
Kerberos 5 mechanism, the cipher block size, which is dependent on
the encryption and decryption transforms, is used only in
krb5_derive_key(), so it is straightforward to replace it.
Tested-by: Scott Mayhew <smayhew@redhat.com>
Reviewed-by: Simo Sorce <simo@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Eliminate the use of bus-locked operations in svc_xprt_enqueue(),
which is a hot path. Replace them with per-cpu variables to reduce
cross-CPU memory bus traffic.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Now that svcauth_gss_prepare_to_wrap() no longer computes the
location of RPC header fields in the response buffer,
svcauth_gss_accept() can save the location of the databody
rather than the location of the verifier.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
To navigate around the space that svcauth_gss_accept() reserves
for the RPC payload body length and sequence number fields,
svcauth_gss_release() does a little dance with the reply's
accept_stat, moving the accept_stat value in the response buffer
down by two words.
Instead, let's have the ->accept() methods each set the proper
final location of the accept_stat to avoid having to move
things.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Currently, svcauth_gss_accept() pre-reserves response buffer space
for the RPC payload length and GSS sequence number before returning
to the dispatcher, which then adds the header's accept_stat field.
The problem is the accept_stat field is supposed to go before the
length and seq_num fields. So svcauth_gss_release() has to relocate
the accept_stat value (see svcauth_gss_prepare_to_wrap()).
To enable these fields to be added to the response buffer in the
correct (final) order, the pointer to the accept_stat has to be made
available to svcauth_gss_accept() so that it can set it before
reserving space for the length and seq_num fields.
As a first step, move the pointer to the location of the accept_stat
field into struct svc_rqst.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
The main part of RPC header encoding and the formation of error
responses are now done using the xdr_stream helpers. Bounds checking
before each XDR data item is encoded makes the server's encoding
path safer against accidental buffer overflows.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Now that each ->accept method has been converted, the
svcxdr_init_encode() calls can be hoisted back up into the generic
RPC server code.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header encoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
This code constructs replies to the decorated NULL procedure calls
that establish GSS contexts. Convert this code path to use struct
xdr_stream to encode such responses.
Done as part of hardening the server-side RPC header encoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
We're now moving svcxdr_init_encode() to /before/ the flavor's
->accept method has set rq_auth_slack. Add a helper that can
set rq_auth_slack /after/ svcxdr_init_encode() has been called.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header encoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header encoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header encoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Refactor: So that the overhaul of each ->accept method can be done
in separate smaller patches, temporarily move the
svcxdr_init_encode() call into those methods.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Now that all vs_dispatch functions invoke svcxdr_init_encode(), it
is common code and can be pushed down into the generic RPC server.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
RFC 5531 defines an MSG_ACCEPTED Reply message like this:
struct accepted_reply {
opaque_auth verf;
union switch (accept_stat stat) {
case SUCCESS:
...
In the current server code, struct opaque_auth encoding is open-
coded. Introduce a helper that encodes an opaque_auth data item
within the context of a xdr_stream.
Done as part of hardening the server-side RPC header decoding and
encoding paths.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
There's no RPC header field called rpc_stat; more precisely, the
variable appears to be recording an accept_stat value. But it looks
like we don't need to preserve this value at all, actually, so
simply remove the variable.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Commit 5b304bc5bf ("[PATCH] knfsd: svcrpc: gss: fix failure on
SVC_DENIED in integrity case") added a check to prevent wrapping an
RPC response if reply_stat == MSG_DENIED, assuming that the only way
to get to svcauth_gss_release() with that reply_stat value was if
the reject_stat was AUTH_ERROR (reject_stat == MISMATCH is handled
earlier in svc_process_common()).
The code there is somewhat confusing. For one thing, rpc_success is
an accept_stat value, not a reply_stat value. The correct reply_stat
value to look for is RPC_MSG_DENIED. It happens to be the same value
as rpc_success, so it all works out, but it's not terribly readable.
Since commit 438623a06b ("SUNRPC: Add svc_rqst::rq_auth_stat"),
the actual auth_stat value is stored in the svc_rqst, so that value
is now available to svcauth_gss_prepare_to_wrap() to make its
decision to wrap, based on direct information about the
authentication status of the RPC caller.
No behavior change is intended, this simply replaces some old code
with something that should be more self-documenting.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Actually xdr_stream does not add value here because of how
gss_wrap() works. This is just a clean-up patch.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Simplify the references to the head and tail iovecs for readability.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Match the error reporting in the other unwrap and wrap functions.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up variable names to match the other unwrap and wrap
functions.
Additionally, the explicit type cast on @gsd in unnecessary; and
@resbuf is renamed to match the variable naming in the unwrap
functions.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header decoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Replace finicky logic: Instead of trying to find scratch space in
the response buffer, use the scratch buffer from struct
gss_svc_data.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
An error computing the checksum here is an exceptional event.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up: To help orient readers, name the stack variables to match
the XDR field names.
Additionally, the explicit type cast on @gsd is unnecessary; and
@resbuf is renamed to match the variable naming in the unwrap
functions.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Now that upper layers use an xdr_stream to track the construction
of each RPC Reply message, resbuf->len is kept up-to-date
automatically. There's no need to recompute it in svc_gss_release().
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Now the entire RPC Call header parsing path is handled via struct
xdr_stream-based decoders.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up: With xdr_stream decoding, the @argv parameter is no longer
used.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header decoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up: Saving the RPC program number in two places is
unnecessary.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Now that each ->accept method has been converted to use xdr_stream,
the svcxdr_init_decode() calls can be hoisted back up into the
generic RPC server code.
The dprintk in svc_authenticate() is removed, since
trace_svc_authenticate() reports the same information.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header decoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Micro-optimizations:
1. The value of rqstp->rq_auth_stat is replaced no matter which
arm of the switch is taken, so the initial assignment can be
safely removed.
2. Avoid checking the value of gc->gc_proc twice in the I/O
(RPC_GSS_PROC_DATA) path.
The cost is a little extra code redundancy.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header decoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header decoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up: To help orient readers, name the stack variables to match
the XDR field names.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header decoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up: To help orient readers, name the stack variables to match
the XDR field names.
For readability, I'm also going to rename the unwrap and wrap
functions in a consistent manner, starting with unwrap_integ_data().
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up / code de-duplication - this functionality is already
available in the generic XDR layer.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
The entire RPC_GSS_PROC_INIT path is converted over to xdr_stream
for decoding the Call credential and verifier.
Done as part of hardening the server-side RPC header decoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
gss_read_verf() is already short. Fold it into its only caller.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
gss_read_common_verf() is now just a wrapper for dup_netobj(), thus
it can be replaced with direct calls to dup_netobj().
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Since upcalls are infrequent, ensure the compiler places the upcall
mechanism out-of-line from the I/O path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header decoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header decoding path.
Since the server-side of the Linux kernel SunRPC implementation
ignores the contents of the Call's machinename field, there's no
need for its RPC_AUTH_UNIX authenticator to reject names that are
larger than UNX_MAXNODENAME.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Done as part of hardening the server-side RPC header decoding path.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
RFC 5531 defines the body of an RPC Call message like this:
struct call_body {
unsigned int rpcvers;
unsigned int prog;
unsigned int vers;
unsigned int proc;
opaque_auth cred;
opaque_auth verf;
/* procedure-specific parameters start here */
};
In the current server code, decoding a struct opaque_auth type is
open-coded in several places, and is thus difficult to harden
everywhere.
Introduce a helper for decoding an opaque_auth within the context
of a xdr_stream. This helper can be shared with all authentication
flavor implemenations, even on the client-side.
Done as part of hardening the server-side RPC header decoding paths.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Refactor: So that the overhaul of each ->accept method can be done
in separate smaller patches, temporarily move the
svcxdr_init_decode() call into those methods.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Now that all vs_dispatch functions invoke svcxdr_init_decode(), it
is common code and can be pushed down into the generic RPC server.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
This is a followup of commit 2558b8039d ("net: use a bounce
buffer for copying skb->mark")
x86 and powerpc define user_access_begin, meaning
that they are not able to perform user copy checks
when using user_write_access_begin() / unsafe_copy_to_user()
and friends [1]
Instead of waiting bugs to trigger on other arches,
add a check_object_size() in put_cmsg() to make sure
that new code tested on x86 with CONFIG_HARDENED_USERCOPY=y
will perform more security checks.
[1] We can not generically call check_object_size() from
unsafe_copy_to_user() because UACCESS is enabled at this point.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent merge from net left-over some unused code in
leftover.c - nomen omen.
Just drop the unused bits.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That really was meant to be a per netns attribute from the beginning.
The idea is that once proper isolation is in place in the main
namespace, additional demux in the child namespaces will be redundant.
Let's make child netns default rps mask empty by default.
To avoid bloating the netns with a possibly large cpumask, allocate
it on-demand during the first write operation.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Add safeguard to check for NULL tupe in objects updates via
NFT_MSG_NEWOBJ, this should not ever happen. From Alok Tiwari.
2) Incorrect pointer check in the new destroy rule command,
from Yang Yingliang.
3) Incorrect status bitcheck in nf_conntrack_udp_packet(),
from Florian Westphal.
4) Simplify seq_print_acct(), from Ilia Gavrilov.
5) Use 2-arg optimal variant of kfree_rcu() in IPVS,
from Julian Anastasov.
6) TCP connection enters CLOSE state in conntrack for locally
originated TCP reset packet from the reject target,
from Florian Westphal.
The fixes#2 and #3 in this series address issues from the previous pull
nf-next request in this net-next cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change icmpv6_echo_reply() to return a drop reason.
For the moment, return NOT_SPECIFIED or SKB_CONSUMED.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hosts can often receive neighbour discovery messages
that are not for them.
Use a dedicated drop reason to make clear the packet is dropped
for this normal case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a generic drop reason for any error detected
in ndisc_parse_options().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ndisc_redirect_rcv() to return a drop reason.
For the moment, return PKT_TOO_SMALL, NOT_SPECIFIED
and values from icmpv6_notify().
More reasons are added later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ndisc_router_discovery() to return a drop reason.
For the moment, return PKT_TOO_SMALL, NOT_SPECIFIED
and SKB_CONSUMED.
More reasons are added later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ndisc_recv_rs() to return a drop reason.
For the moment, return PKT_TOO_SMALL, NOT_SPECIFIED
or SKB_CONSUMED. More reasons are added later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ndisc_recv_na() to return a drop reason.
For the moment, return PKT_TOO_SMALL, NOT_SPECIFIED
or SKB_CONSUMED. More reasons are added later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ndisc_recv_ns() to return a drop reason.
For the moment, return PKT_TOO_SMALL, NOT_SPECIFIED
or SKB_CONSUMED.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we try to start AF_XDP on some machines with long running time, due
to the machine's memory fragmentation problem, there is no sufficient
contiguous physical memory that will cause the start failure.
If the size of the queue is 8 * 1024, then the size of the desc[] is
8 * 1024 * 8 = 16 * PAGE, but we also add struct xdp_ring size, so it is
16page+. This is necessary to apply for a 4-order memory. If there are a
lot of queues, it is difficult to these machine with long running time.
Here, that we actually waste 15 pages. 4-Order memory is 32 pages, but
we only use 17 pages.
This patch replaces __get_free_pages() by vmalloc() to allocate memory
to solve these problems.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a certain probability that following
exceptions will occur in the wrk benchmark test:
Running 10s test @ http://11.213.45.6:80
8 threads and 64 connections
Thread Stats Avg Stdev Max +/- Stdev
Latency 3.72ms 13.94ms 245.33ms 94.17%
Req/Sec 1.96k 713.67 5.41k 75.16%
155262 requests in 10.10s, 23.10MB read
Non-2xx or 3xx responses: 3
We will find that the error is HTTP 400 error, which is a serious
exception in our test, which means the application data was
corrupted.
Consider the following scenarios:
CPU0 CPU1
buf_desc->used = 0;
cmpxchg(buf_desc->used, 0, 1)
deal_with(buf_desc)
memset(buf_desc->cpu_addr,0);
This will cause the data received by a victim connection to be cleared,
thus triggering an HTTP 400 error in the server.
This patch exchange the order between clear used and memset, add
barrier to ensure memory consistency.
Fixes: 1c5526968e ("net/smc: Clear memory when release and reuse buffer")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a certain chance to trigger the following panic:
PID: 5900 TASK: ffff88c1c8af4100 CPU: 1 COMMAND: "kworker/1:48"
#0 [ffff9456c1cc79a0] machine_kexec at ffffffff870665b7
#1 [ffff9456c1cc79f0] __crash_kexec at ffffffff871b4c7a
#2 [ffff9456c1cc7ab0] crash_kexec at ffffffff871b5b60
#3 [ffff9456c1cc7ac0] oops_end at ffffffff87026ce7
#4 [ffff9456c1cc7ae0] page_fault_oops at ffffffff87075715
#5 [ffff9456c1cc7b58] exc_page_fault at ffffffff87ad0654
#6 [ffff9456c1cc7b80] asm_exc_page_fault at ffffffff87c00b62
[exception RIP: ib_alloc_mr+19]
RIP: ffffffffc0c9cce3 RSP: ffff9456c1cc7c38 RFLAGS: 00010202
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000004
RDX: 0000000000000010 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88c1ea281d00 R8: 000000020a34ffff R9: ffff88c1350bbb20
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
R13: 0000000000000010 R14: ffff88c1ab040a50 R15: ffff88c1ea281d00
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff9456c1cc7c60] smc_ib_get_memory_region at ffffffffc0aff6df [smc]
#8 [ffff9456c1cc7c88] smcr_buf_map_link at ffffffffc0b0278c [smc]
#9 [ffff9456c1cc7ce0] __smc_buf_create at ffffffffc0b03586 [smc]
The reason here is that when the server tries to create a second link,
smc_llc_srv_add_link() has no protection and may add a new link to
link group. This breaks the security environment protected by
llc_conf_mutex.
Fixes: 2d2209f201 ("net/smc: first part of add link processing as SMC server")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes no sense to keep randomly large max_sdu values, especially if
larger than the device's max_mtu. These are visible in "tc qdisc show".
Such a max_sdu is practically unlimited and will cause no packets for
that traffic class to be dropped on enqueue.
Just set max_sdu_dynamic to U32_MAX, which in the logic below causes
taprio to save a max_frm_len of U32_MAX and a max_sdu presented to user
space of 0 (unlimited).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The overhead specified in the size table comes from the user. With small
time intervals (or gates always closed), the overhead can be larger than
the max interval for that traffic class, and their difference is
negative.
What we want to happen is for max_sdu_dynamic to have the smallest
non-zero value possible (1) which means that all packets on that traffic
class are dropped on enqueue. However, since max_sdu_dynamic is u32, a
negative is represented as a large value and oversized dropping never
happens.
Use max_t with int to force a truncation of max_frm_len to no smaller
than dev->hard_header_len + 1, which in turn makes max_sdu_dynamic no
smaller than 1.
Fixes: fed87cc671 ("net/sched: taprio: automatically calculate queueMaxSDU based on TC gate durations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
taprio_calculate_gate_durations() depends on netdev_get_num_tc() and
this returns 0. So it calculates the maximum gate durations for no
traffic class.
I had tested the blamed commit only with another patch in my tree, one
which in the end I decided isn't valuable enough to submit ("net/sched:
taprio: mask off bits in gate mask that exceed number of TCs").
The problem is that having this patch threw off my testing. By moving
the netdev_set_num_tc() call earlier, we implicitly gave to
taprio_calculate_gate_durations() the information it needed.
Extract only the portion from the unsubmitted change which applies the
mqprio configuration to the netdev earlier.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20230130173145.475943-15-vladimir.oltean@nxp.com/
Fixes: a306a90c8f ("net/sched: taprio: calculate tc gate durations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix three cases of overproduction of wakeups:
(1) rxrpc_input_split_jumbo() conditionally notifies the app that there's
data for recvmsg() to collect if it queues some data - and then its
only caller, rxrpc_input_data(), goes and wakes up recvmsg() anyway.
Fix the rxrpc_input_data() to only do the wakeup in failure cases.
(2) If a DATA packet is received for a call by the I/O thread whilst
recvmsg() is busy draining the call's rx queue in the app thread, the
call will left on the recvmsg() queue for recvmsg() to pick up, even
though there isn't any data on it.
This can cause an unexpected recvmsg() with a 0 return and no MSG_EOR
set after the reply has been posted to a service call.
Fix this by discarding pending calls from the recvmsg() queue that
don't need servicing yet.
(3) Not-yet-completed calls get requeued after having data read from them,
even if they have no data to read.
Fix this by only requeuing them if they have data waiting on them; if
they don't, the I/O thread will requeue them when data arrives or they
fail.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/3386149.1676497685@warthog.procyon.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In order to prevent a device from disappearing when a background job was
started, dev_hold() and dev_put() calls were made. During the
stabilization phase of the scan/beacon features, it was later decided
that removing the device while a background job was ongoing was a valid use
case, and we should instead stop the background job and then remove the
device, rather than prevent the device from being removed. This is what
is currently done, which means manually reference counting the device
during background jobs is no longer needed.
Fixes: ed3557c947 ("ieee802154: Add support for user scanning requests")
Fixes: 9bc114504b ("ieee802154: Add support for user beaconing requests")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230214135035.1202471-7-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
At this stage we simply do not care about the delayed work value,
because active scan is not yet supported, so we can blindly queue
another work once a beacon has been sent.
It fixes a smatch warning:
mac802154_beacon_worker() warn: always true condition
'(local->beacon_interval >= 0) => (0-u32max >= 0)'
Fixes: 3accf47627 ("mac802154: Handle basic beaconing")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230214135035.1202471-6-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Using ieee802154_subif_start_xmit() to bypass the net queue when
sending beacons is broken because it does not acquire the
HARD_TX_LOCK(), hence not preventing datagram buffers to be smashed by
beacons upon contention situation. Using the mlme_tx helper is not the
best fit either but at least it is not buggy and has little-to-no
performance hit. More details are given in the comment explaining this
choice in the code.
Fixes: 3accf47627 ("mac802154: Handle basic beaconing")
Reported-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230214135035.1202471-5-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Returning EPERM gives the impression that "right now" it is not
possible, but "later" it could be, while what we want to express is the
fact that this is not currently supported at all (might change in the
future). So let's return EOPNOTSUPP instead.
Fixes: ed3557c947 ("ieee802154: Add support for user scanning requests")
Suggested-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230214135035.1202471-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Instead of printing error messages in the kernel log, let's use extack.
When there is a netlink error returned that could be further specified
with a string, use extack as well.
Apply this logic to the very recent scan/beacon infrastructure.
Fixes: ed3557c947 ("ieee802154: Add support for user scanning requests")
Fixes: 9bc114504b ("ieee802154: Add support for user beaconing requests")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230214135035.1202471-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Instead of open-coding scan parameters (page, channels, duration, etc),
let's use the existing NLA_POLICY* macros. This help greatly reducing
the error handling and clarifying the overall logic.
Fixes: ed3557c947 ("ieee802154: Add support for user scanning requests")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230214135035.1202471-2-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
The bpf_fib_lookup() also looks up the neigh table.
This was done before bpf_redirect_neigh() was added.
In the use case that does not manage the neigh table
and requires bpf_fib_lookup() to lookup a fib to
decide if it needs to redirect or not, the bpf prog can
depend only on using bpf_redirect_neigh() to lookup the
neigh. It also keeps the neigh entries fresh and connected.
This patch adds a bpf_fib_lookup flag, SKIP_NEIGH, to avoid
the double neigh lookup when the bpf prog always call
bpf_redirect_neigh() to do the neigh lookup. The params->smac
output is skipped together when SKIP_NEIGH is set because
bpf_redirect_neigh() will figure out the smac also.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230217205515.3583372-1-martin.lau@linux.dev
The bpf_fib_lookup() helper does not only look up the fib (ie. route)
but it also looks up the neigh. Before returning the neigh, the helper
does not check for NUD_VALID. When a neigh state (neigh->nud_state)
is in NUD_FAILED, its dmac (neigh->ha) could be all zeros. The helper
still returns SUCCESS instead of NO_NEIGH in this case. Because of the
SUCCESS return value, the bpf prog directly uses the returned dmac
and ends up filling all zero in the eth header.
This patch checks for NUD_VALID and returns NO_NEIGH if the neigh is
not valid.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230217004150.2980689-3-martin.lau@linux.dev
Some of the bpf helpers require bh disabled. eg. The bpf_fib_lookup
helper that will be used in a latter selftest. In particular, it
calls ___neigh_lookup_noref that expects the bh disabled.
This patch disables bh before calling bpf_prog_run[_xdp], so
the testing prog can also use those helpers.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230217004150.2980689-2-martin.lau@linux.dev
iptables/nftables support responding to tcp packets with tcp resets.
The generated tcp reset packet passes through both output and postrouting
netfilter hooks, but conntrack will never see them because the generated
skb has its ->nfct pointer copied over from the packet that triggered the
reset rule.
If the reset rule is used for established connections, this
may result in the conntrack entry to be around for a very long
time (default timeout is 5 days).
One way to avoid this would be to not copy the nf_conn pointer
so that the rest packet passes through conntrack too.
Problem is that output rules might not have the same conntrack
zone setup as the prerouting ones, so its possible that the
reset skb won't find the correct entry. Generating a template
entry for the skb seems error prone as well.
Add an explicit "closing" function that switches a confirmed
conntrack entry to closed state and wire this up for tcp.
If the entry isn't confirmed, no action is needed because
the conntrack entry will never be committed to the table.
Reported-by: Russel King <linux@armlinux.org.uk>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* EHT channel puncturing support (client & AP)
* some support for AP MLD without mac80211
* fixes for A-MSDU on mesh connections
Major driver changes:
iwlwifi
* EHT rate reporting
* Bump FW API to 74 for AX devices
* STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware
mt76
* switch to using page pool allocator
* mt7996 EHT (Wi-Fi 7) support
* Wireless Ethernet Dispatch (WED) reset support
libertas
* WPS enrollee support
brcmfmac
* Rename Cypress 89459 to BCM4355
* BCM4355 and BCM4377 support
mwifiex
* SD8978 chipset support
rtl8xxxu
* LED support
ath12k
* new driver for Qualcomm Wi-Fi 7 devices
ath11k
* IPQ5018 support
* Fine Timing Measurement (FTM) responder role support
* channel 177 support
ath10k
* store WLAN firmware version in SMEM image table
-----BEGIN PGP SIGNATURE-----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=p6+A
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-03-16' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Major stack changes:
* EHT channel puncturing support (client & AP)
* some support for AP MLD without mac80211
* fixes for A-MSDU on mesh connections
Major driver changes:
iwlwifi
* EHT rate reporting
* Bump FW API to 74 for AX devices
* STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware
mt76
* switch to using page pool allocator
* mt7996 EHT (Wi-Fi 7) support
* Wireless Ethernet Dispatch (WED) reset support
libertas
* WPS enrollee support
brcmfmac
* Rename Cypress 89459 to BCM4355
* BCM4355 and BCM4377 support
mwifiex
* SD8978 chipset support
rtl8xxxu
* LED support
ath12k
* new driver for Qualcomm Wi-Fi 7 devices
ath11k
* IPQ5018 support
* Fine Timing Measurement (FTM) responder role support
* channel 177 support
ath10k
* store WLAN firmware version in SMEM image table
* tag 'wireless-next-2023-03-16' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (207 commits)
wifi: brcmfmac: p2p: Introduce generic flexible array frame member
wifi: mac80211: add documentation for amsdu_mesh_control
wifi: cfg80211: remove gfp parameter from cfg80211_obss_color_collision_notify description
wifi: mac80211: always initialize link_sta with sta
wifi: mac80211: pass 'sta' to ieee80211_rx_data_set_sta()
wifi: cfg80211: Set SSID if it is not already set
wifi: rtw89: move H2C of del_pkt_offload before polling FW status ready
wifi: rtw89: use readable return 0 in rtw89_mac_cfg_ppdu_status()
wifi: rtw88: usb: drop now unnecessary URB size check
wifi: rtw88: usb: send Zero length packets if necessary
wifi: rtw88: usb: Set qsel correctly
wifi: mac80211: fix off-by-one link setting
wifi: mac80211: Fix for Rx fragmented action frames
wifi: mac80211: avoid u32_encode_bits() warning
wifi: mac80211: Don't translate MLD addresses for multicast
wifi: cfg80211: call reg_notifier for self managed wiphy from driver hint
wifi: cfg80211: get rid of gfp in cfg80211_bss_color_notify
wifi: nl80211: Allow authentication frames and set keys on NAN interface
wifi: mac80211: fix non-MLO station association
wifi: mac80211: Allow NSS change only up to capability
...
====================
Link: https://lore.kernel.org/r/20230216105406.208416-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "flavors" framework defined in RFC8986 [1] represents additional
operations that can modify or extend a subset of existing behaviors such as
SRv6 End, End.X and End.T. We report these flavors hereafter:
- Penultimate Segment Pop (PSP);
- Ultimate Segment Pop (USP);
- Ultimate Segment Decapsulation (USD).
Depending on how the Segment Routing Header (SRH) has to be handled, an
SRv6 End* behavior can support these flavors either individually or in
combinations.
In this patch, we only consider the PSP flavor for the SRv6 End behavior.
A PSP enabled SRv6 End behavior is used by the Source/Ingress SR node
(i.e., the one applying the SRv6 Policy) when it needs to instruct the
penultimate SR Endpoint node listed in the SID List (carried by the SRH) to
remove the SRH from the IPv6 header.
Specifically, a PSP enabled SRv6 End behavior processes the SRH by:
i) decreasing the Segment Left (SL) from 1 to 0;
ii) copying the Last Segment IDentifier (SID) into the IPv6 Destination
Address (DA);
iii) removing (i.e., popping) the outer SRH from the extension headers
following the IPv6 header.
It is important to note that PSP operation (steps i, ii, iii) takes place
only at a penultimate SR Segment Endpoint node (i.e., when the SL=1) and
does not happen at non-penultimate Endpoint nodes. Indeed, when a SID of
PSP flavor is processed at a non-penultimate SR Segment Endpoint node, the
PSP operation is not performed because it would not be possible to decrease
the SL from 1 to 0.
SL=2 SL=1 SL=0
| | |
For example, given the SRv6 policy (SID List := < X, Y, Z >):
- a PSP enabled SRv6 End behavior bound to SID "Y" will apply the PSP
operation as Segment Left (SL) is 1, corresponding to the Penultimate
Segment of the SID List;
- a PSP enabled SRv6 End behavior bound to SID "X" will *NOT* apply the
PSP operation as the Segment Left is 2. This behavior instance will
apply the "standard" End packet processing, ignoring the configured PSP
flavor at all.
[1] - RFC8986: https://datatracker.ietf.org/doc/html/rfc8986
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The End nexthop lookup/input operations are moved into a new helper
function named input_action_end_finish(). This avoids duplicating the
code needed to compute the nexthop in the different flavors of the End
behavior.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cited commit changed devlink to register its netdev notifier block on
the global netdev notifier chain instead of on the per network namespace
one.
However, when changing the network namespace of the devlink instance,
devlink still tries to unregister its notifier block from the chain of
the old namespace and register it on the chain of the new namespace.
This results in corruption of the notifier chains, as the same notifier
block is registered on two different chains: The global one and the per
network namespace one. In turn, this causes other problems such as the
inability to dismantle namespaces due to netdev reference count issues.
Fix by preventing devlink from moving its notifier block between
namespaces.
Reproducer:
# echo "10 1" > /sys/bus/netdevsim/new_device
# ip netns add test123
# devlink dev reload netdevsim/netdevsim10 netns test123
# ip netns del test123
[ 71.935619] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 71.938348] leaked reference.
Fixes: 565b4824c3 ("devlink: change port event netdev notifier from per-net to global")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20230215073139.1360108-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since act_pedit now has access to percpu counters, use the
tcf_action_inc_overlimit_qstats wrapper that will use the percpu
counter whenever they are available.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tc action act_gate was using shared stats, move it to percpu stats.
tdc results:
1..12
ok 1 5153 - Add gate action with priority and sched-entry
ok 2 7189 - Add gate action with base-time
ok 3 a721 - Add gate action with cycle-time
ok 4 c029 - Add gate action with cycle-time-ext
ok 5 3719 - Replace gate base-time action
ok 6 d821 - Delete gate action with valid index
ok 7 3128 - Delete gate action with invalid index
ok 8 7837 - List gate actions
ok 9 9273 - Flush gate actions
ok 10 c829 - Add gate action with duplicate index
ok 11 3043 - Add gate action with invalid index
ok 12 2930 - Add gate action with cookie
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tc action act_connmark was using shared stats and taking the per
action lock in the datapath. Improve it by using percpu stats and rcu.
perf before:
- 13.55% tcf_connmark_act
- 81.18% _raw_spin_lock
80.46% native_queued_spin_lock_slowpath
perf after:
- 2.85% tcf_connmark_act
tdc results:
1..15
ok 1 2002 - Add valid connmark action with defaults
ok 2 56a5 - Add valid connmark action with control pass
ok 3 7c66 - Add valid connmark action with control drop
ok 4 a913 - Add valid connmark action with control pipe
ok 5 bdd8 - Add valid connmark action with control reclassify
ok 6 b8be - Add valid connmark action with control continue
ok 7 d8a6 - Add valid connmark action with control jump
ok 8 aae8 - Add valid connmark action with zone argument
ok 9 2f0b - Add valid connmark action with invalid zone argument
ok 10 9305 - Add connmark action with unsupported argument
ok 11 71ca - Add valid connmark action and replace it
ok 12 5f8f - Add valid connmark action with cookie
ok 13 c506 - Replace connmark with invalid goto chain control
ok 14 6571 - Delete connmark action with valid index
ok 15 3426 - Delete connmark action with invalid index
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tc action act_nat was using shared stats and taking the per action
lock in the datapath. Improve it by using percpu stats and rcu.
perf before:
- 10.48% tcf_nat_act
- 81.83% _raw_spin_lock
81.08% native_queued_spin_lock_slowpath
perf after:
- 0.48% tcf_nat_act
tdc results:
1..27
ok 1 7565 - Add nat action on ingress with default control action
ok 2 fd79 - Add nat action on ingress with pipe control action
ok 3 eab9 - Add nat action on ingress with continue control action
ok 4 c53a - Add nat action on ingress with reclassify control action
ok 5 76c9 - Add nat action on ingress with jump control action
ok 6 24c6 - Add nat action on ingress with drop control action
ok 7 2120 - Add nat action on ingress with maximum index value
ok 8 3e9d - Add nat action on ingress with invalid index value
ok 9 f6c9 - Add nat action on ingress with invalid IP address
ok 10 be25 - Add nat action on ingress with invalid argument
ok 11 a7bd - Add nat action on ingress with DEFAULT IP address
ok 12 ee1e - Add nat action on ingress with ANY IP address
ok 13 1de8 - Add nat action on ingress with ALL IP address
ok 14 8dba - Add nat action on egress with default control action
ok 15 19a7 - Add nat action on egress with pipe control action
ok 16 f1d9 - Add nat action on egress with continue control action
ok 17 6d4a - Add nat action on egress with reclassify control action
ok 18 b313 - Add nat action on egress with jump control action
ok 19 d9fc - Add nat action on egress with drop control action
ok 20 a895 - Add nat action on egress with DEFAULT IP address
ok 21 2572 - Add nat action on egress with ANY IP address
ok 22 37f3 - Add nat action on egress with ALL IP address
ok 23 6054 - Add nat action on egress with cookie
ok 24 79d6 - Add nat action on ingress with cookie
ok 25 4b12 - Replace nat action with invalid goto chain control
ok 26 b811 - Delete nat action with valid index
ok 27 a521 - Delete nat action with invalid index
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The kernel stack can be more consistent by printing the IFF_PROMISC
aka promiscuous enable/disable messages with the standard netdev_info
message which can include bus and driver info as well as the device.
typical command usage from user space looks like:
ip link set eth0 promisc <on|off>
But lots of utilities such as bridge, tcpdump, etc put the interface into
promiscuous mode.
old message:
[ 406.034418] device eth0 entered promiscuous mode
[ 408.424703] device eth0 left promiscuous mode
new message:
[ 406.034431] ice 0000:17:00.0 eth0: entered promiscuous mode
[ 408.424715] ice 0000:17:00.0 eth0: left promiscuous mode
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the user sets or clears the IFF_ALLMULTI flag in the netdev, there are
no log messages printed to the kernel log to indicate anything happened.
This is inexplicably different from most other dev->flags changes, and
could suprise the user.
Typically this occurs from user-space when a user:
ip link set eth0 allmulticast <on|off>
However, other devices like bridge set allmulticast as well, and many
other flows might trigger entry into allmulticast as well.
The new message uses the standard netdev_info print and looks like:
[ 413.246110] ixgbe 0000:17:00.0 eth0: entered allmulticast mode
[ 415.977184] ixgbe 0000:17:00.0 eth0: left allmulticast mode
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The rsvp classifier has served us well for about a quarter of a century but has
has not been getting much maintenance attention due to lack of known users.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tcindex classifier has served us well for about a quarter of a century
but has not been getting much TLC due to lack of known users. Most recently
it has become easy prey to syzkaller. For this reason, we are retiring it.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The dsmark qdisc has served us well over the years for diffserv but has not
been getting much attention due to other more popular approaches to do diffserv
services. Most recently it has become a shooting target for syzkaller. For this
reason, we are retiring it.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ATM qdisc has served us well over the years but has not been getting much
TLC due to lack of known users. Most recently it has become a shooting target
for syzkaller. For this reason, we are retiring it.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
While this amazing qdisc has served us well over the years it has not been
getting any tender love and care and has bitrotted over time.
It has become mostly a shooting target for syzkaller lately.
For this reason, we are retiring it. Goodbye CBQ - we loved you.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
MSG_ZEROCOPY ensures that pinned user pages do not exceed the limit.
If no limit is set, skip this accounting as otherwise expensive
atomic_long operations are called for no reason.
This accounting is already skipped for privileged (CAP_IPC_LOCK)
users. Rely on the same mechanism: if no mmp->user is set,
mm_unaccount_pinned_pages does not decrement either.
Tested by running tools/testing/selftests/net/msg_zerocopy.sh with
an unprivileged user for the TXMODE binary:
ip netns exec "${NS1}" sudo -u "{$USER}" "${BIN}" "-${IP}" ...
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230214155740.3448763-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all devlink health callbacks and related code are in file
health.c move common health functions and devlink_health_reporter struct
to be local in health.c file.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move devlink health report test callback from leftover.c to health.c. No
functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move devlink health report dump callbacks and related code from
leftover.c to health.c. No functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Devlink fmsg (formatted message) is used by devlink health diagnose,
dump and drivers which support these devlink health callbacks.
Therefore, move devlink fmsg helpers and related code to file health.c.
Move devlink health diagnose to file health.c. No functional change in
this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move devlink health report helper and recover callback and related code
from leftover.c to health.c. No functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move devlink health get and set callbacks and related code from
leftover.c to health.c. No functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
devlink_nl_health_reporter_fill() error flow calls nla_nest_end(). Fix
it to call nla_nest_cancel() instead.
Note the bug is harmless as genlmsg_cancel() cancel the entire message,
so no fixes tag added.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move devlink health reporter create/destroy and related dev code to new
file health.c. This file shall include all callbacks and functionality
that are related to devlink health.
In addition, fix kdoc indentation and make reporter create/destroy kdoc
more clear. No functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
&xdp_buff and &xdp_frame are bound in a way that
xdp_buff->data_hard_start == xdp_frame
It's always the case and e.g. xdp_convert_buff_to_frame() relies on
this.
IOW, the following:
for (u32 i = 0; i < 0xdead; i++) {
xdpf = xdp_convert_buff_to_frame(&xdp);
xdp_convert_frame_to_buff(xdpf, &xdp);
}
shouldn't ever modify @xdpf's contents or the pointer itself.
However, "live packet" code wrongly treats &xdp_frame as part of its
context placed *before* the data_hard_start. With such flow,
data_hard_start is sizeof(*xdpf) off to the right and no longer points
to the XDP frame.
Instead of replacing `sizeof(ctx)` with `offsetof(ctx, xdpf)` in several
places and praying that there are no more miscalcs left somewhere in the
code, unionize ::frm with ::data in a flex array, so that both starts
pointing to the actual data_hard_start and the XDP frame actually starts
being a part of it, i.e. a part of the headroom, not the context.
A nice side effect is that the maximum frame size for this mode gets
increased by 40 bytes, as xdp_buff::frame_sz includes everything from
data_hard_start (-> includes xdpf already) to the end of XDP/skb shared
info.
Also update %MAX_PKT_SIZE accordingly in the selftests code. Leave it
hardcoded for 64 bit && 4k pages, it can be made more flexible later on.
Minor: align `&head->data` with how `head->frm` is assigned for
consistency.
Minor #2: rename 'frm' to 'frame' in &xdp_page_head while at it for
clarity.
(was found while testing XDP traffic generator on ice, which calls
xdp_convert_frame_to_buff() for each XDP frame)
Fixes: b530e9e106 ("bpf: Add "live packet" mode for XDP in BPF_PROG_RUN")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20230215185440.4126672-1-aleksander.lobakin@intel.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This documentation wasn't added in the original patch,
add it now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 6e4c0d0460 ("wifi: mac80211: add a workaround for receiving non-standard mesh A-MSDU")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we have multiple interfaces receiving the same frame,
such as a multicast frame, one interface might have a sta
and the other not. In this case, link_sta would be set but
not cleared again.
Always set link_sta, so we keep an invariant that link_sta
and sta are either both set or both not set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's at least one case in ieee80211_rx_for_interface()
where we might pass &((struct sta_info *)NULL)->sta to it
only to then do container_of(), and then checking the
result for NULL, but checking the result of container_of()
for NULL looks really odd.
Fix this by just passing the struct sta_info * instead.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a connection was established without going through
NL80211_CMD_CONNECT, the ssid was never set in the wireless_dev struct.
Now we set it in __cfg80211_connect_result() when it is not already set.
When using a userspace configuration that does not call
cfg80211_connect() (can be checked with breakpoints in the kernel),
this patch should allow `networkctl status device_name` to output the
SSID instead of null.
Cc: stable@vger.kernel.org
Reported-by: Yohan Prod'homme <kernel@zoddo.fr>
Fixes: 7b0a0e3c3a (wifi: cfg80211: do some rework towards MLO link APIs)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216711
Signed-off-by: Marc Bornand <dev.mbornand@systemb.ch>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When swap is activated to a file on an NFSv4 mount we arrange that the
state manager thread is always present as starting a new thread requires
memory allocations that might block waiting for swap.
Unfortunately the code for allowing the state manager thread to exit when
swap is disabled was not tested properly and does not work.
This can be seen by examining /proc/fs/nfsfs/servers after disabling swap
and unmounting the filesystem. The servers file will still list one
entry. Also a "ps" listing will show the state manager thread is still
present.
There are two problems.
1/ rpc_clnt_swap_deactivate() doesn't walk up the ->cl_parent list to
find the primary client on which the state manager runs.
2/ The thread is not woken up properly and it immediately goes back to
sleep without checking whether it is really needed. Using
nfs4_schedule_state_manager() ensures a proper wake-up.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes: 4dc73c6791 ("NFSv4: keep state manager thread active if swap is enabled")
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
lianhui reports that when MPLS fails to register the sysctl table
under new location (during device rename) the old pointers won't
get overwritten and may be freed again (double free).
Handle this gracefully. The best option would be unregistering
the MPLS from the device completely on failure, but unfortunately
mpls_ifdown() can fail. So failing fully is also unreliable.
Another option is to register the new table first then only
remove old one if the new one succeeds. That requires more
code, changes order of notifications and two tables may be
visible at the same time.
sysctl point is not used in the rest of the code - set to NULL
on failures and skip unregister if already NULL.
Reported-by: lianhui tang <bluetlh@gmail.com>
Fixes: 0fae3bf018 ("mpls: handle device renames for per-device sysctls")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e48c414ee6 ("[INET]: Generalise the TCP sock ID lookup routines")
commented out the definition of SOCK_REFCNT_DEBUG in 2005 and later another
commit 463c84b97f ("[NET]: Introduce inet_connection_sock") removed it.
Since we could track all of them through bpf and kprobe related tools
and the feature could print loads of information which might not be
that helpful even under a little bit pressure, the whole feature which
has been inactive for many years is no longer supported.
Link: https://lore.kernel.org/lkml/20230211065153.54116-1-kerneljasonxing@gmail.com/
Suggested-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definitions to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definition to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When sending a SYN message, this kernel stack trace is observed:
...
[ 13.396352] RIP: 0010:_copy_from_iter+0xb4/0x550
...
[ 13.398494] Call Trace:
[ 13.398630] <TASK>
[ 13.398630] ? __alloc_skb+0xed/0x1a0
[ 13.398630] tipc_msg_build+0x12c/0x670 [tipc]
[ 13.398630] ? shmem_add_to_page_cache.isra.71+0x151/0x290
[ 13.398630] __tipc_sendmsg+0x2d1/0x710 [tipc]
[ 13.398630] ? tipc_connect+0x1d9/0x230 [tipc]
[ 13.398630] ? __local_bh_enable_ip+0x37/0x80
[ 13.398630] tipc_connect+0x1d9/0x230 [tipc]
[ 13.398630] ? __sys_connect+0x9f/0xd0
[ 13.398630] __sys_connect+0x9f/0xd0
[ 13.398630] ? preempt_count_add+0x4d/0xa0
[ 13.398630] ? fpregs_assert_state_consistent+0x22/0x50
[ 13.398630] __x64_sys_connect+0x16/0x20
[ 13.398630] do_syscall_64+0x42/0x90
[ 13.398630] entry_SYSCALL_64_after_hwframe+0x63/0xcd
It is because commit a41dad905e ("iov_iter: saner checks for attempt
to copy to/from iterator") has introduced sanity check for copying
from/to iov iterator. Lacking of copy direction from the iterator
viewpoint would lead to kernel stack trace like above.
This commit fixes this issue by initializing the iov iterator with
the correct copy direction when sending SYN or ACK without data.
Fixes: f25dcc7687 ("tipc: tipc ->sendmsg() conversion")
Reported-by: syzbot+d43608d061e8847ec9f3@syzkaller.appspotmail.com
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Link: https://lore.kernel.org/r/20230214012606.5804-1-tung.q.nguyen@dektech.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definitions to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The convention for find_first_bit() is 0-based, while ffs()
is 1-based, so this is now off-by-one. I cannot reproduce the
gcc-9 problem, but since the -1 is now removed, I'm hoping it
will still avoid the original issue.
Reported-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Fixes: 1d8d4af434 ("wifi: mac80211: avoid u32_encode_bits() warning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_accept_frame() function performs a number of early checks
to decide whether or not further processing needs to be done on a frame.
One of those checks is the ieee80211_is_robust_mgmt_frame() function.
It requires to peek into the frame payload, but because defragmentation
does not occur until later on in the receive path, this peek is invalid
for any fragment other than the first one. Also, in this scenario there
is no STA and so the fragmented frame will be dropped later on in the
process and will not reach the upper stack. This can happen with large
action frames at low rates, for example, we see issues with DPP on S1G.
This change will only check if the frame is robust if it's the first
fragment. Invalid fragmented packets will be discarded later after
defragmentation is completed.
Signed-off-by: Gilad Itzkovitch <gilad.itzkovitch@morsemicro.com>
Link: https://lore.kernel.org/r/20221124005336.1618411-1-gilad.itzkovitch@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
gcc-9 triggers a false-postive warning in ieee80211_mlo_multicast_tx()
for u32_encode_bits(ffs(links) - 1, ...), since ffs() can return zero
on an empty bitmask, and the negative argument to u32_encode_bits()
is then out of range:
In file included from include/linux/ieee80211.h:21,
from include/net/cfg80211.h:23,
from net/mac80211/tx.c:23:
In function 'u32_encode_bits',
inlined from 'ieee80211_mlo_multicast_tx' at net/mac80211/tx.c:4437:17,
inlined from 'ieee80211_subif_start_xmit' at net/mac80211/tx.c:4485:3:
include/linux/bitfield.h:177:3: error: call to '__field_overflow' declared with attribute error: value doesn't fit into mask
177 | __field_overflow(); \
| ^~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:197:2: note: in expansion of macro '____MAKE_OP'
197 | ____MAKE_OP(u##size,u##size,,)
| ^~~~~~~~~~~
include/linux/bitfield.h:200:1: note: in expansion of macro '__MAKE_OP'
200 | __MAKE_OP(32)
| ^~~~~~~~~
Newer compiler versions do not cause problems with the zero argument
because they do not consider this a __builtin_constant_p().
It's also harmless since the hweight16() check already guarantees
that this cannot be 0.
Replace the ffs() with an equivalent find_first_bit() check that
matches the later for_each_set_bit() style and avoids the warning.
Fixes: 963d0e8d08 ("wifi: mac80211: optionally implement MLO multicast TX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230214132025.1532147-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change on network namespace only makes sense during re-init reload
action. For FW activation it is not applicable. So check if user passed
an ATTR indicating network namespace change request and forbid it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20230213115836.3404039-1-jiri@resnulli.us
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
MLD address translation should be done only for individually addressed
frames. Otherwise, AAD calculation would be wrong and the decryption
would fail.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Link: https://lore.kernel.org/r/20230214101048.792414-1-andrei.otcheretianski@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the regulatory driver does not call the regulatory callback
reg_notifier for self managed wiphys. Sometimes driver needs cfg80211
to calculate the info of ieee80211_channel such as flags and power,
and driver needs to get the info of ieee80211_channel after hint of
driver, but driver does not know when calculation of the info of
ieee80211_channel become finished, so add notify to driver in
reg_process_self_managed_hint() from cfg80211 is a good way, then
driver could get the correct info in callback of reg_notifier.
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230201065313.27203-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wi-Fi Aware R4 specification defines NAN Pairing which uses PASN handshake
to authenticate the peer and generate keys. Hence allow to register and transmit
the PASN authentication frames on NAN interface and set the keys to driver or
underlying modules on NAN interface.
The driver needs to configure the feature flag NL80211_EXT_FEATURE_SECURE_NAN,
which also helps userspace modules to know if the driver supports secure NAN.
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
Link: https://lore.kernel.org/r/1675519179-24174-1-git-send-email-quic_vganneva@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Non-MLO station frames are dropped in Rx path due to the condition
check in ieee80211_rx_is_valid_sta_link_id(). In multi-link AP scenario,
non-MLO stations try to connect in any of the valid links in the ML AP,
where the station valid_links and link_id params are valid in the
ieee80211_sta object. But ieee80211_rx_is_valid_sta_link_id() always
return false for the non-MLO stations by the assumption taken is
valid_links and link_id are not valid in non-MLO stations object
(ieee80211_sta), this assumption is wrong. Due to this assumption,
non-MLO station frames are dropped which leads to failure in association.
Fix it by removing the condition check and allow the link validation
check for the non-MLO stations.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://lore.kernel.org/r/20230206160330.1613-1-quic_periyasa@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stations can update bandwidth/NSS change in
VHT action frame with action type Operating Mode Notification.
(IEEE Std 802.11-2020 - 9.4.1.53 Operating Mode field)
For Operating Mode Notification, an RX NSS change to a value
greater than AP's maximum NSS should not be allowed.
During fuzz testing, by forcefully sending VHT Op. mode notif.
frames from STA with random rx_nss values, it is found that AP
accepts rx_nss values greater that APs maximum NSS instead of
discarding such NSS change.
Hence allow NSS change only up to maximum NSS that is negotiated
and capped to AP's capability during association.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/20230207114146.10567-1-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least ath10k and ath11k supported hardware (maybe more) does not implement
mesh A-MSDU aggregation in a standard compliant way.
802.11-2020 9.3.2.2.2 declares that the Mesh Control field is part of the
A-MSDU header (and little-endian).
As such, its length must not be included in the subframe length field.
Hardware affected by this bug treats the mesh control field as part of the
MSDU data and sets the length accordingly.
In order to avoid packet loss, keep track of which stations are affected
by this and take it into account when converting A-MSDU to 802.3 + mesh control
packets.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current mac80211 mesh A-MSDU receive path fails to parse A-MSDU packets
on mesh interfaces, because it assumes that the Mesh Control field is always
directly after the 802.11 header.
802.11-2020 9.3.2.2.2 Figure 9-70 shows that the Mesh Control field is
actually part of the A-MSDU subframe header.
This makes more sense, since it allows packets for multiple different
destinations to be included in the same A-MSDU, as long as RA and TID are
still the same.
Another issue is the fact that the A-MSDU subframe length field was apparently
accidentally defined as little-endian in the standard.
In order to fix this, the mesh forwarding path needs happen at a different
point in the receive path.
ieee80211_data_to_8023_exthdr is changed to ignore the mesh control field
and leave it in after the ethernet header. This also affects the source/dest
MAC address fields, which now in the case of mesh point to the mesh SA/DA.
ieee80211_amsdu_to_8023s is changed to deal with the endian difference and
to add the Mesh Control length to the subframe length, since it's not covered
by the MSDU length field.
With these changes, the mac80211 will get the same packet structure for
converted regular data packets and unpacked A-MSDU subframes.
The mesh forwarding checks are now only performed after the A-MSDU decap.
For locally received packets, the Mesh Control header is stripped away.
For forwarded packets, a new 802.11 header gets added.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-4-nbd@nbd.name
[fix fortify build error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that all drivers use iTXQ, it does not make sense to check to drop
tx forwarding packets when the driver has stopped the queues.
fq_codel will take care of dropping packets when the queues fill up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing the outer A-MSDU header, don't check for inner bridge tunnel
or RFC1042 headers. This is handled by ieee80211_amsdu_to_8023s already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The value of last_rate in ieee80211_sta_rx_stats is degraded from u32 to
u16 after being assigned to rate variable, which causes information loss
in STA_STATS_FIELD_TYPE and later bitfields.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://lore.kernel.org/r/20230209110659.25447-1-shayne.chen@mediatek.com
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230206081641.3193-1-liubo03@inspur.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently action frames TX only with ML address as A3(BSSID) are
allowed in an ML AP, but TX for a non-ML Station can happen in any
link of an ML BSS with link BSS address as A3.
In case of an MLD, if User-space has provided a valid link_id in
action frame TX request, allow transmission of the frame in that link.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/20230201061602.3918-1-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Configure the bitmap in link_conf and notify the driver.
- Modify 'change' in ieee80211_start_ap() from u32 to u64 to support
BSS_CHANGED_EHT_PUNCTURING.
- Propagate the bitmap in channel switch events to userspace.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Link: https://lore.kernel.org/r/20230131001227.25014-5-quic_alokad@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- New feature flag, NL80211_EXT_FEATURE_PUNCT, to advertise
driver support for preamble puncturing in AP mode.
- New attribute, NL80211_ATTR_PUNCT_BITMAP, to receive a puncturing
bitmap from the userspace during AP bring up (NL80211_CMD_START_AP)
and channel switch (NL80211_CMD_CHANNEL_SWITCH) operations. Each bit
corresponds to a 20 MHz channel in the operating bandwidth, lowest
bit for the lowest channel. Bit set to 1 indicates that the channel
is punctured. Higher 16 bits are reserved.
- New members added to structures cfg80211_ap_settings and
cfg80211_csa_settings to propagate the bitmap to the driver after
validation.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Link: https://lore.kernel.org/r/20230131001227.25014-3-quic_alokad@quicinc.com
[move validation against 0xffff into policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Move ieee80211_valid_disable_subchannel_bitmap() from mlme.c to
chan.c, rename it as cfg80211_valid_disable_subchannel_bitmap()
and export it.
- Modify the prototype to include struct cfg80211_chan_def instead
of only bandwidth to support a check which returns false if the
primary channel is punctured.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://lore.kernel.org/r/20230131001227.25014-2-quic_alokad@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an error message to the missing frequency case to have all
-EINVAL in nl80211_parse_chandef() return a better error.
Signed-off-by: Jaewan Kim <jaewan@google.com>
Link: https://lore.kernel.org/r/20230130074514.1560021-1-jaewan@google.com
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211_send_ap_stopped() can be called multiple times on the same
netdev for each link when using Multi-Link Operation. Add the
MLO_LINK_ID attribute to the event to allow userspace to distinguish
which link the event is for.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://lore.kernel.org/r/20230128125844.2407135-2-alvin@pqrs.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace processes such as network daemons may wish to be informed when
any AP interface is brought up on the system, for example to initiate a
(re)configuration of IP settings or to start a DHCP server.
Currently nl80211 does not broadcast any such event on its multicast
groups, leaving userspace only two options:
1. the process must be the one that actually issued the
NL80211_CMD_START_AP request, so that it can react on the response to
that request;
2. the process must react to RTM_NEWLINK events indicating a change in
carrier state, and may query for further information about the AP and
react accordingly.
Option (1) is robust, but it does not cover all scenarios. It is easy to
imagine a situation where this is not the case (e.g. hostapd +
systemd-networkd).
Option (2) is not robust, because RTM_NEWLINK events may be silently
discarded by the linkwatch logic (cf. linkwatch_fire_event()).
Concretely, consider a scenario in which the carrier state flip-flops in
the following way:
^ carrier state (high/low = carrier/no carrier)
|
| _______ _______ ...
| | | |
| ______| "foo" |____| "bar" (SSID in "quotes")
|
+-------A-------B----C---------> time
If the time interval between (A) and (C) is less than 1 second, then
linkwatch may emit only a single RTM_NEWLINK event indicating carrier
gain.
This is problematic because it is possible that the network
configuration that should be applied is a function of the AP's
properties such as SSID (cf. SSID= in systemd.network(5)). As
illustrated in the above diagram, it may be that the AP with SSID "bar"
ends up being configured as though it had SSID "foo".
Address the above issue by having nl80211 emit an NL80211_CMD_START_AP
message on the MLME nl80211 multicast group. This allows for arbitrary
processes to be reliably informed.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://lore.kernel.org/r/20230128125844.2407135-1-alvin@pqrs.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Handle the Puncturing info received from the AP in the
EHT Operation element in beacons.
If the info is invalid:
- during association: disable EHT connection for the AP
- after association: disconnect
This commit includes many (internal) bugfixes and spec
updates various people.
Co-developed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/r/20230127123930.4fbc74582331.I3547481d49f958389f59dfeba3fcc75e72b0aa6e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to offload OWE processing to user space for MLD AP when
driver's SME in use.
Add new parameters in struct cfg80211_update_owe_info to provide below
information in cfg80211_update_owe_info_event() call:
- MLO link ID of the AP, with which station requested (re)association.
This is applicable for both MLO and non-MLO station connections when
the AP affiliated with an MLD.
- Station's MLD address if the connection is MLO capable.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20230126143256.960563-3-quic_vjakkam@quicinc.com
[reformat the trace event macro]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for drivers to indicate STA connection(MLO/non-MLO) when
user space SME (e.g., hostapd) is not used for MLD AP.
Add new parameters in struct station_info to provide below information
in cfg80211_new_sta() call:
- MLO link ID of the AP, with which station completed (re)association.
This is applicable for both MLO and non-MLO station connections when
the AP affiliated with an MLD.
- Station's MLD address if the connection is MLO capable.
- (Re)Association Response IEs sent to the station. User space needs
this to determine rejected and accepted affiliated links information
of the connected station if the connection is MLO capable.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20230126143256.960563-2-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move color collision report in a dedicated delayed work and do not run
it in interrupt context in order to rate-limit the number of events
reported to userspace. Moreover grab wdev mutex in
ieee80211_color_collision_detection_work routine since it is required
by cfg80211_obss_color_collision_notify().
Tested-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Fixes: 5f9404abdf ("mac80211: add support for BSS color change")
Link: https://lore.kernel.org/r/3f6cf60c892ad40c1cca4a55d62b1224ef1c6ce9.1674644379.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Key information in wext.connect is not reset on (re)connect and can hold
data from a previous connection.
Reset key data to avoid that drivers or mac80211 incorrectly detect a
WEP connection request and access the freed or already reused memory.
Additionally optimize cfg80211_sme_connect() and avoid an useless
schedule of conn_work.
Fixes: fffd0934b9 ("cfg80211: rework key operation")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230124141856.356646-1-alexander@wetzel-home.de
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently authentication request event interface doesn't have support to
indicate the user space whether it should enable MLO or not during the
authentication with the specified AP. But driver needs such capability
since the connection is MLO or not decided by the driver in case of SME
offload to the driver.
Add support for driver to indicate MLD address of the AP in
authentication offload request to inform user space to enable MLO during
authentication process. Driver shall look at NL80211_ATTR_MLO_SUPPORT
flag capability in NL80211_CMD_CONNECT to know whether the user space
supports enabling MLO during the authentication offload.
User space should enable MLO during the authentication only when it
receives the AP MLD address in authentication offload request. User
space shouldn't enable MLO if the authentication offload request doesn't
indicate the AP MLD address even if the AP is MLO capable.
When MLO is enabled, user space should use the MAC address of the
interface (on which driver sent request) as self MLD address. User space
and driver to use MLD addresses in RA, TA and BSSID fields of the frames
between them, and driver translates the MLD addresses to/from link
addresses based on the link chosen for the authentication.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20230116125058.1604843-1-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are currently two mechanisms for populating hardware stats:
1. Using flow_offload api to query the flow's statistics.
The api assumes that the same stats values apply to all
the flow's actions.
This assumption breaks when action drops or jumps over following
actions.
2. Using hw_action api to query specific action stats via a driver
callback method. This api assures the correct action stats for
the offloaded action, however, it does not apply to the rest of the
actions in the flow's actions array.
Extend the flow_offload stats callback to indicate that a per action
stats update is required.
Use the existing flow_offload_action api to query the action's hw stats.
In addition, currently the tc action stats utility only updates hw actions.
Reuse the existing action stats cb infrastructure to query any action
stats.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently a hardware action is uniquely identified by the <id, hw_index>
tuple. However, the id is set by the flow_act_setup callback and tc core
cannot enforce this, and it is possible that a future change could break
this. In addition, <id, hw_index> are not unique across network namespaces.
Uniquely identify the action by setting an action cookie by the tc core.
Use the unique action cookie to query the action's hardware stats.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of passing 6 stats related args, pass the flow_stats.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A single tc pedit action may be translated to multiple flow_offload
actions.
Offload only actions that translate to a single pedit command value.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently the hw action stats update is called from tcf_exts_hw_stats_update,
when a tc filter is dumped, and from tcf_action_copy_stats, when a hw
action is dumped.
However, the tcf_action_copy_stats is also called from tcf_action_dump.
As such, the hw action stats update cb is called 3 times for every
tc flower filter dump.
Move the tc action hw stats update from tcf_action_copy_stats to
tcf_dump_walker to update the hw action stats when tc action is dumped.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tc action act_ctinfo was using shared stats, fix it to use percpu stats
since bstats_update() must be called with locks or with a percpu pointer argument.
tdc results:
1..12
ok 1 c826 - Add ctinfo action with default setting
ok 2 0286 - Add ctinfo action with dscp
ok 3 4938 - Add ctinfo action with valid cpmark and zone
ok 4 7593 - Add ctinfo action with drop control
ok 5 2961 - Replace ctinfo action zone and action control
ok 6 e567 - Delete ctinfo action with valid index
ok 7 6a91 - Delete ctinfo action with invalid index
ok 8 5232 - List ctinfo actions
ok 9 7702 - Flush ctinfo actions
ok 10 3201 - Add ctinfo action with duplicate index
ok 11 8295 - Add ctinfo action with invalid index
ok 12 3964 - Replace ctinfo action with invalid goto_chain control
Fixes: 24ec483cec ("net: sched: Introduce act_ctinfo action")
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20230210200824.444856-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Creates three new drop reasons:
SKB_DROP_REASON_IPV6_NDISC_FRAG: invalid frag (suppress_frag_ndisc).
SKB_DROP_REASON_IPV6_NDISC_HOP_LIMIT: invalid hop limit.
SKB_DROP_REASON_IPV6_NDISC_BAD_CODE: invalid NDISC icmp6 code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Accurately reports what happened in icmpv6_notify() when handling
a packet.
This makes use of the new IPV6_BAD_EXTHDR drop reason.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to what was done for TX_PUSH, add an RX_PUSH concept
to the ethtool interfaces.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tls_encrypt_done only uses aead_req to get ahold of
the tls_rec object. So we could pass that in instead of aead_req
to simplify the code.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto_async_request passed to the completion is not guaranteed
to be the original request object. Only the data field can be relied
upon.
Fix this by storing the socket pointer with the AEAD request.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds temporary scaffolding so that the Crypto API
completion function can take a void * instead of crypto_async_request.
Once affected users have been converted this can be removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds temporary scaffolding so that the Crypto API
completion function can take a void * instead of crypto_async_request.
Once affected users have been converted this can be removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds temporary scaffolding so that the Crypto API
completion function can take a void * instead of crypto_async_request.
Once affected users have been converted this can be removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When converting net_device_stats to rtnl_link_stats64 sign extension
is triggered on ILP32 machines as 6c1c509778 changed the previous
"ulong -> u64" conversion to "long -> u64" by accessing the
net_device_stats fields through a (signed) atomic_long_t.
This causes for example the received bytes counter to jump to 16EiB after
having received 2^31 bytes. Casting the atomic value to "unsigned long"
beforehand converting it into u64 avoids this.
Fixes: 6c1c509778 ("net: add atomic_long_t to net_device_stats fields")
Signed-off-by: Felix Riemann <felix.riemann@sma.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TCA_STAB attribute is malformed, qdisc_get_stab() returns
an error, and we end up calling ops->destroy() while ops->init()
has not been called yet.
While we are at it, call qdisc_put_stab() after ops->destroy().
Fixes: 1f62879e36 ("net/sched: make stab available before ops->init() call")
Reported-by: syzbot+d44d88f1d11e6ca8576b@syzkaller.appspotmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver calling devl_param_driverinit_value_set() has to hold devlink
instance lock while doing that. Put an assertion there.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver maintains following basic sane behavior, the
devl_param_driverinit_value_get() function could be called without
holding instance lock:
1) Driver ensures a call to devl_param_driverinit_value_get() cannot
race with registering/unregistering the parameter with
the same parameter ID.
2) Driver ensures a call to devl_param_driverinit_value_get() cannot
race with devl_param_driverinit_value_set() call with
the same parameter ID.
3) Driver ensures a call to devl_param_driverinit_value_get() cannot
race with reload operation.
By the nature of params usage, these requirements should be
trivially achievable. If the driver for some off reason
is not able to comply, it has to take the devlink->lock while
calling devl_param_driverinit_value_get().
Remove the lock assertion and add comment describing
the locking requirements.
This fixes a splat in mlx5 driver introduced by the commit
referenced in the "Fixes" tag.
Lore: https://lore.kernel.org/netdev/719de4f0-76ac-e8b9-38a9-167ae239efc7@amd.com/
Reported-by: Kim Phillips <kim.phillips@amd.com>
Fixes: 075935f0ae ("devlink: protect devlink param list by instance lock")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loose the linked list for params and use xarray instead.
Note that this is required to be eventually possible to call
devl_param_driverinit_value_get() without holding instance lock.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As xarray has an iterator helper that allows to start from specified
index, use this directly and avoid repeated iteration from 0.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probably due to copy-paste error, the name of the arg is "init_val"
which is misleading, as the pointer is used to point to struct where to
store the current value. Rename it to "val" and change the arg comment
a bit on the way.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driverinit param purpose is to serve the driver during init/reload
time to provide a value, either default or set by user.
Make sure that driver does not read value updated by user before the
reload is performed. Hold the new value in a separate struct and switch
it during reload.
Note that this is required to be eventually possible to call
devl_param_driverinit_value_get() without holding instance lock.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to treat string params any different comparing to other types.
Rely on the struct assign to copy the whole struct, including the
string.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
old_meter needs to be free after it is detached regardless of whether
the new meter is successfully attached.
Fixes: c7c4c44c9a ("net: openvswitch: expand the meters supported number")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NL_SET_ERR_MSG_MOD inserts the KBUILD_MODNAME and a ':' before the actual
extended error message. The devlink feature hasn't been able to be compiled
as a module since commit f4b6bcc700 ("net: devlink: turn devlink into a
built-in").
Stop using NL_SET_ERR_MSG_MOD, and just use the base NL_SET_ERR_MSG. This
aligns the extended error messages better with the NL_SET_ERR_MSG_ATTR
messages as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rds_rm_zerocopy_callback() uses list_add_tail() with swapped
arguments. This links the list head with the new entry, losing
the references to the remaining part of the list.
Fixes: 9426bbc6de ("rds: use list structure to track information for zerocopy completion notification")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since x->encap of pfkey_msg2xfrm_state() is not
initialized to 0, kernel heap data can be leaked.
Fix with kzalloc() to prevent this.
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet pointed out [0] that when we call skb_set_owner_r()
for ipv6_pinfo.pktoptions, sk_rmem_schedule() has not been called,
resulting in a negative sk_forward_alloc.
We add a new helper which clones a skb and sets its owner only
when sk_rmem_schedule() succeeds.
Note that we move skb_set_owner_r() forward in (dccp|tcp)_v6_do_rcv()
because tcp_send_synack() can make sk_forward_alloc negative before
ipv6_opt_accepted() in the crossed SYN-ACK or self-connect() cases.
[0]: https://lore.kernel.org/netdev/CANn89iK9oc20Jdi_41jb9URdF210r7d1Y-+uypbMSbOfY6jqrg@mail.gmail.com/
Fixes: 323fbd0edf ("net: dccp: Add handling of IPV6_PKTOPTIONS to dccp_v6_do_rcv()")
Fixes: 3df80d9320 ("[DCCP]: Introduce DCCPv6")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The imperfect hash area can be updated while packets are traversing,
which will cause a use-after-free when 'tcf_exts_exec()' is called
with the destroyed tcf_ext.
CPU 0: CPU 1:
tcindex_set_parms tcindex_classify
tcindex_lookup
tcindex_lookup
tcf_exts_change
tcf_exts_exec [UAF]
Stop operating on the shared area directly, by using a local copy,
and update the filter with 'rcu_replace_pointer()'. Delete the old
filter version only after a rcu grace period elapsed.
Fixes: 9b0d4446b5 ("net: sched: avoid atomic swap in tcf_exts_change")
Reported-by: valis <sec@valis.email>
Suggested-by: valis <sec@valis.email>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Link: https://lore.kernel.org/r/20230209143739.279867-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use list_is_first() to check whether tsp->asoc matches the first
element of ep->asocs, as the list is not guaranteed to have an entry.
Fixes: 8f840e47f1 ("sctp: add the sctp_diag.c file")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20230208-sctp-filter-v2-1-6e1f4017f326@diag.uniroma1.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Future patches are going to move parts of the bridge MDB code to the
common rtnetlink code in preparation for VXLAN MDB support. To
facilitate code sharing between both drivers, move the validation of the
top level attributes in RTM_{NEW,DEL}MDB messages to a policy that will
eventually be moved to the rtnetlink code.
Use 'NLA_NESTED' for 'MDBA_SET_ENTRY_ATTRS' instead of
NLA_POLICY_NESTED() as this attribute is going to be validated using
different policies in the underlying drivers.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The purpose of the sequence generation counter in the netlink callback
is to identify if a multipart dump is consistent or not by calling
nl_dump_check_consistent() whenever a message is generated.
The function is not invoked by the MDB code, rendering the sequence
generation counter assignment pointless. Remove it.
Note that even if the function was invoked, we still could not
accurately determine if the dump is consistent or not, as there is no
sequence generation counter for MDB entries, unlike nexthop objects, for
example.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'MDB_PG_FLAGS_PERMANENT' and 'MDB_PERMANENT' happen to have the same
value, but the latter is uAPI and cannot change, so use it when dumping
an MDB entry.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Add new PID/VID 0489:e0f2 for MT7921
- Add VID:PID 13d3:3529 for Realtek RTL8821CE
- Add CIS feature bits to controller information
- Set Per Platform Antenna Gain(PPAG) for Intel controllers
-----BEGIN PGP SIGNATURE-----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=lKcZ
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2023-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
pull-request: bluetooth-next
- Add new PID/VID 0489:e0f2 for MT7921
- Add VID:PID 13d3:3529 for Realtek RTL8821CE
- Add CIS feature bits to controller information
- Set Per Platform Antenna Gain(PPAG) for Intel controllers
* tag 'for-net-next-2023-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next:
Bluetooth: btintel: Set Per Platform Antenna Gain(PPAG)
Bluetooth: Make sure LE create conn cancel is sent when timeout
Bluetooth: Free potentially unfreed SCO connection
Bluetooth: hci_qca: get wakeup status from serdev device handle
Bluetooth: L2CAP: Fix potential user-after-free
Bluetooth: MGMT: add CIS feature bits to controller information
Bluetooth: hci_conn: Refactor hci_bind_bis() since it always succeeds
Bluetooth: HCI: Replace zero-length arrays with flexible-array members
Bluetooth: qca: Fix sparse warnings
Bluetooth: btusb: Add VID:PID 13d3:3529 for Realtek RTL8821CE
Bluetooth: btusb: Add new PID/VID 0489:e0f2 for MT7921
Bluetooth: Fix issue with Actions Semi ATS2851 based devices
====================
Link: https://lore.kernel.org/r/20230209234922.3756173-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCY+bZrwAKCRDbK58LschI
gzi4AP4+TYo0jnSwwkrOoN9l4f5VO9X8osmj3CXfHBv7BGWVxAD/WnvA3TDZyaUd
agIZTkRs6BHF9He8oROypARZxTeMLwM=
=nO1C
-----END PGP SIGNATURE-----
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now handle_fragments() in OVS and TC have the similar code, and
this patch removes the duplicate code by moving the function
to nf_conntrack_ovs.
Note that skb_clear_hash(skb) or skb->ignore_df = 1 should be
done only when defrag returns 0, as it does in other places
in kernel.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch has no functional changes and just moves frag check and
tc_skb_cb update out of handle_fragments, to make it easier to move
the duplicate code from handle_fragments() into nf_conntrack_ovs later.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch has no functional changes and just moves key and ovs_cb update
out of handle_fragments, and skb_clear_hash() and skb->ignore_df change
into handle_fragments(), to make it easier to move the duplicate code
from handle_fragments() into nf_conntrack_ovs later.
Note that it changes to pass info->family to handle_fragments() instead
of key for the packet type check, as info->family is set according to
key->eth.type in ovs_ct_copy_action() when creating the action.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are almost the same code in ovs_skb_network_trim() and
tcf_ct_skb_network_trim(), this patch extracts them into a function
nf_ct_skb_network_trim() and moves the function to nf_conntrack_ovs.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to nf_nat_ovs created by Commit ebddb14049 ("net: move the
nat function to nf_nat_ovs for ovs and tc"), this patch is to create
nf_conntrack_ovs to get these functions shared by OVS and TC only.
There are nf_ct_helper() and nf_ct_add_helper() from nf_conntrak_helper
in this patch, and will be more in the following patches.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
skbuff_head_cache is misnamed (perhaps for historical reasons?)
because it does not hold heads. Head is the buffer which skb->data
points to, and also where shinfo lives. struct sk_buff is a metadata
structure, not the head.
Eric recently added skb_small_head_cache (which allocates actual
head buffers), let that serve as an excuse to finally clean this up :)
Leave the user-space visible name intact, it could possibly be uAPI.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=1nmF
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-next-20230208' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc development
Here are some miscellaneous changes for rxrpc:
(1) Use consume_skb() rather than kfree_skb_reason().
(2) Fix unnecessary waking when poking and already-poked call.
(3) Add ack.rwind to the rxrpc_tx_ack tracepoint as this indicates how
many incoming DATA packets we're telling the peer that we are
currently willing to accept on this call.
(4) Reduce duplicate ACK transmission. We send ACKs to let the peer know
that we're increasing the receive window (ack.rwind) as we consume
packets locally. Normal ACK transmission is triggered in three places
and that leads to duplicates being sent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot was able to trigger a warning [1] from net_free()
calling ref_tracker_dir_exit(&net->notrefcnt_tracker)
while the corresponding ref_tracker_dir_init() has not been
done yet.
copy_net_ns() can indeed bypass the call to setup_net()
in some error conditions.
Note:
We might factorize/move more code in preinit_net() in the future.
[1]
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 0 PID: 5817 Comm: syz-executor.3 Not tainted 6.2.0-rc7-next-20230208-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/12/2023
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd9/0x150 lib/dump_stack.c:106
assign_lock_key kernel/locking/lockdep.c:982 [inline]
register_lock_class+0xdb6/0x1120 kernel/locking/lockdep.c:1295
__lock_acquire+0x10a/0x5df0 kernel/locking/lockdep.c:4951
lock_acquire.part.0+0x11c/0x370 kernel/locking/lockdep.c:5691
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x3d/0x60 kernel/locking/spinlock.c:162
ref_tracker_dir_exit+0x52/0x600 lib/ref_tracker.c:24
net_free net/core/net_namespace.c:442 [inline]
net_free+0x98/0xd0 net/core/net_namespace.c:436
copy_net_ns+0x4f3/0x6b0 net/core/net_namespace.c:493
create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110
unshare_nsproxy_namespaces+0xc1/0x1f0 kernel/nsproxy.c:228
ksys_unshare+0x449/0x920 kernel/fork.c:3205
__do_sys_unshare kernel/fork.c:3276 [inline]
__se_sys_unshare kernel/fork.c:3274 [inline]
__x64_sys_unshare+0x31/0x40 kernel/fork.c:3274
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
Fixes: 0cafd77dcd ("net: add a refcount tracker for kernel sockets")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230208182123.3821604-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Take into account the IPV6_TCLASS socket option (DSCP) in
tcp_v6_connect(). Otherwise fib6_rule_match() can't properly
match the DSCP value, resulting in invalid route lookup.
For example:
ip route add unreachable table main 2001:db8::10/124
ip route add table 100 2001:db8::10/124 dev eth0
ip -6 rule add dsfield 0x04 table 100
echo test | socat - TCP6:[2001:db8::11]:54321,ipv6-tclass=0x04
Without this patch, socat fails at connect() time ("No route to host")
because the fib-rule doesn't jump to table 100 and the lookup ends up
being done in the main table.
Fixes: 2cc67cc731 ("[IPV6] ROUTE: Routing by Traffic Class.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Take into account the IPV6_TCLASS socket option (DSCP) in
ip6_datagram_flow_key_init(). Otherwise fib6_rule_match() can't
properly match the DSCP value, resulting in invalid route lookup.
For example:
ip route add unreachable table main 2001:db8::10/124
ip route add table 100 2001:db8::10/124 dev eth0
ip -6 rule add dsfield 0x04 table 100
echo test | socat - UDP6:[2001:db8::11]:54321,ipv6-tclass=0x04
Without this patch, socat fails at connect() time ("No route to host")
because the fib-rule doesn't jump to table 100 and the lookup ends up
being done in the main table.
Fixes: 2cc67cc731 ("[IPV6] ROUTE: Routing by Traffic Class.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use string_is_terminated() helper instead of cpecific memchr() call.
This shows better the intention of the call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230208133153.22528-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use string_is_terminated() helper instead of cpecific memchr() call.
This shows better the intention of the call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230208133153.22528-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move string_is_valid() to the header for wider use.
While at it, rename to string_is_terminated() to be
precise about its semantics.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230208133153.22528-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If RPS is enabled, this allows configuring a default rps
mask, which is effective since receive queue creation time.
A default RPS mask allows the system admin to ensure proper
isolation, avoiding races at network namespace or device
creation time.
The default RPS mask is initially empty, and can be
modified via a newly added sysctl entry.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Will simplify the following patch. No functional change
intended.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Will be used by the following patch to avoid code
duplication. No functional changes intended.
The only difference is that now flow_limit_cpu_sysctl() will
always compute the flow limit mask on each read operation,
even when read() will not return any byte to user-space.
Note that the new helper is placed under a new #ifdef at
the file start to better fit the usage in the later patch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace direct modifications to vma->vm_flags with calls to modifier
functions to be able to track flag changes and to keep vma locking
correctness.
[akpm@linux-foundation.org: fix drivers/misc/open-dice.c, per Hyeonggon Yoo]
Link: https://lkml.kernel.org/r/20230126193752.297968-5-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Minchan Kim <minchan@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Peter Oskolkov <posk@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Punit Agrawal <punit.agrawal@bytedance.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When sending LE create conn command, we set a timer with a duration of
HCI_LE_CONN_TIMEOUT before timing out and calling
create_le_conn_complete. Additionally, when receiving the command
complete, we also set a timer with the same duration to call
le_conn_timeout.
Usually the latter will be triggered first, which then sends a LE
create conn cancel command. However, due to the nature of racing, it
is possible for the former to be called first, thereby calling the
chain hci_conn_failed -> hci_conn_del -> cancel_delayed_work, thereby
preventing LE create conn cancel to be sent. In this situation, the
controller will be stuck in trying the LE connection.
This patch flushes le_conn_timeout on create_le_conn_complete to make
sure we always send LE create connection cancel, if necessary.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is possible to initiate a SCO connection while deleting the
corresponding ACL connection, e.g. in below scenario:
(1) < hci setup sync connect command
(2) > hci disconn complete event (for the acl connection)
(3) > hci command complete event (for(1), failure)
When it happens, hci_cs_setup_sync_conn won't be able to obtain the
reference to the SCO connection, so it will be stuck and potentially
hinder subsequent connections to the same device.
This patch prevents that by also deleting the SCO connection if it is
still not established when the corresponding ACL connection is deleted.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes all instances of which requires to allocate a buffer calling
alloc_skb which may release the chan lock and reacquire later which
makes it possible that the chan is disconnected in the meantime.
Fixes: a6a5568c03 ("Bluetooth: Lock the L2CAP channel when sending")
Reported-by: Alexander Coffin <alex.coffin@matician.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Userspace needs to know whether the adapter has feature support for
Connected Isochronous Stream - Central/Peripheral, so it can set up
LE Audio features accordingly.
Expose these feature bits as settings in MGMT controller info.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The compiler thinks "conn" might be NULL after a call to hci_bind_bis(),
which cannot happen. Avoid any confusion by just making it not return a
value since it cannot fail. Fixes the warnings seen with GCC 13:
In function 'arch_atomic_dec_and_test',
inlined from 'atomic_dec_and_test' at ../include/linux/atomic/atomic-instrumented.h:576:9,
inlined from 'hci_conn_drop' at ../include/net/bluetooth/hci_core.h:1391:6,
inlined from 'hci_connect_bis' at ../net/bluetooth/hci_conn.c:2124:3:
../arch/x86/include/asm/rmwcc.h:37:9: warning: array subscript 0 is outside array bounds of 'atomic_t[0]' [-Warray-bounds=]
37 | asm volatile (fullop CC_SET(cc) \
| ^~~
...
In function 'hci_connect_bis':
cc1: note: source object is likely at address zero
Fixes: eca0ae4aea ("Bluetooth: Add initial implementation of BIS connections")
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
NFT_MSG_GETSETELEM returns -EPERM when fetching set elements that belong
to table that has an owner. This results in empty set/map listing from
userspace.
Fixes: 6001a930ce ("netfilter: nftables: introduce table ownership")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
rds_rm_zerocopy_callback() uses list_entry() on the head of a list
causing a type confusion.
Use list_first_entry() to actually access the first element of the
rs_zcookie_queue list.
Fixes: 9426bbc6de ("rds: use list structure to track information for zerocopy completion notification")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Link: https://lore.kernel.org/r/20230202-rds-zerocopy-v3-1-83b0df974f9a@diag.uniroma1.it
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=Bkiy
-----END PGP SIGNATURE-----
Merge tag 'ipsec-2023-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
ipsec 2023-02-08
1) Fix policy checks for nested IPsec tunnels when using
xfrm interfaces. From Benedict Wong.
2) Fix netlink message expression on 32=>64-bit
messages translators. From Anastasia Belova.
3) Prevent potential spectre v1 gadget in xfrm_xlate32_attr.
From Eric Dumazet.
4) Always consistently use time64_t in xfrm_timer_handler.
From Eric Dumazet.
5) Fix KCSAN reported bug: Multiple cpus can update use_time
at the same time. From Eric Dumazet.
6) Fix SCP copy from IPv4 to IPv6 on interfamily tunnel.
From Christian Hopps.
* tag 'ipsec-2023-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: fix bug with DSCP copy to v6 from v4 tunnel
xfrm: annotate data-race around use_time
xfrm: consistently use time64_t in xfrm_timer_handler()
xfrm/compat: prevent potential spectre v1 gadget in xfrm_xlate32_attr()
xfrm: compat: change expression for switch in xfrm_xlate64
Fix XFRM-I support for nested ESP tunnels
====================
Link: https://lore.kernel.org/r/20230208114322.266510-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce a temporary variable to check for an invalid configuration
attempt from user space. Before this patch the value was copied to
the real config variable and rolled back in the case of an error.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230203090807.97100-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Improve commit 497cc00224 ("taprio: Handle short intervals and large
packets") to only perform segmentation when skb->len exceeds what
taprio_dequeue() expects.
In practice, this will make the biggest difference when a traffic class
gate is always open in the schedule. This is because the max_frm_len
will be U32_MAX, and such large skb->len values as Kurt reported will be
sent just fine unsegmented.
What I don't seem to know how to handle is how to make sure that the
segmented skbs themselves are smaller than the maximum frame size given
by the current queueMaxSDU[tc]. Nonetheless, we still need to drop
those, otherwise the Qdisc will hang.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The majority of the taprio_enqueue()'s function is spent doing TCP
segmentation, which doesn't look right to me. Compilers shouldn't have a
problem in inlining code no matter how we write it, so move the
segmentation logic to a separate function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
taprio today has a huge problem with small TC gate durations, because it
might accept packets in taprio_enqueue() which will never be sent by
taprio_dequeue().
Since not much infrastructure was available, a kludge was added in
commit 497cc00224 ("taprio: Handle short intervals and large
packets"), which segmented large TCP segments, but the fact of the
matter is that the issue isn't specific to large TCP segments (and even
worse, the performance penalty in segmenting those is absolutely huge).
In commit a54fc09e4c ("net/sched: taprio: allow user input of per-tc
max SDU"), taprio gained support for queueMaxSDU, which is precisely the
mechanism through which packets should be dropped at qdisc_enqueue() if
they cannot be sent.
After that patch, it was necessary for the user to manually limit the
maximum MTU per TC. This change adds the necessary logic for taprio to
further limit the values specified (or not specified) by the user to
some minimum values which never allow oversized packets to be sent.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have one practical reason for doing this and one concerning correctness.
The practical reason has to do with a follow-up patch, which aims to mix
2 sources of max_sdu (one coming from the user and the other automatically
calculated based on TC gate durations @current link speed). Among those
2 sources of input, we must always select the smaller max_sdu value, but
this can change at various link speeds. So the max_sdu coming from the
user must be kept separated from the value that is operationally used
(the minimum of the 2), because otherwise we overwrite it and forget
what the user asked us to do.
To solve that, this patch proposes that struct sched_gate_list contains
the operationally active max_frm_len, and q->max_sdu contains just what
was requested by the user.
The reason having to do with correctness is based on the following
observation: the admin sched_gate_list becomes operational at a given
base_time in the future. Until then, it is inactive and applies no
shaping, all gates are open, etc. So the queueMaxSDU dropping shouldn't
apply either (this is a mechanism to ensure that packets smaller than
the largest gate duration for that TC don't hang the port; clearly it
makes little sense if the gates are always open).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vinicius intended taprio to take the L1 overhead into account when
estimating packet transmission time through user input, specifically
through the qdisc size table (man tc-stab).
Something like this:
tc qdisc replace dev $eth root stab overhead 24 taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 \
sched-entry S 0x7e 9000000 \
sched-entry S 0x82 1000000 \
max-sdu 0 0 0 0 0 0 0 200 \
flags 0x0 clockid CLOCK_TAI
Without the overhead being specified, transmission times will be
underestimated and will cause late transmissions. For an offloading
driver, it might even cause TX hangs if there is no open gate large
enough to send the maximum sized packets for that TC (including L1
overhead). Properly knowing the L1 overhead will ensure that we are able
to auto-calculate the queueMaxSDU per traffic class just right, and
avoid these hangs due to head-of-line blocking.
We can't make the stab mandatory due to existing setups, but we can warn
the user that it's important with a warning netlink extack.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220505160357.298794-1-vladimir.oltean@nxp.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some qdiscs like taprio turn out to be actually pretty reliant on a well
configured stab, to not underestimate the skb transmission time (by
properly accounting for L1 overhead).
In a future change, taprio will need the stab, if configured by the
user, to be available at ops->init() time. It will become even more
important in upcoming work, when the overhead will be used for the
queueMaxSDU calculation that is passed to an offloading driver.
However, rcu_assign_pointer(sch->stab, stab) is called right after
ops->init(), making it unavailable, and I don't really see a good reason
for that.
Move it earlier, which nicely seems to simplify the error handling path
as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
taprio_dequeue_from_txq() looks at the entry->end_time to determine
whether the skb will overrun its traffic class gate, as if at the end of
the schedule entry there surely is a "gate close" event for it. Hint:
maybe there isn't.
For each schedule entry, introduce an array of kernel times which
actually tracks when in the future will there be an *actual* gate close
event for that traffic class, and use that in the guard band overrun
calculation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently taprio assumes that the budget for a traffic class expires at
the end of the current interval as if the next interval contains a "gate
close" event for this traffic class.
This is, however, an unfounded assumption. Allow schedule entry
intervals to be fused together for a particular traffic class by
calculating the budget until the gate *actually* closes.
This means we need to keep budgets per traffic class, and we also need
to update the budget consumption procedure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a confusion in terms in taprio which makes what is called
"close_time" to be actually used for 2 things:
1. determining when an entry "closes" such that transmitted skbs are
never allowed to overrun that time (?!)
2. an aid for determining when to advance and/or restart the schedule
using the hrtimer
It makes more sense to call this so-called "close_time" "end_time",
because it's not clear at all to me what "closes". Future patches will
hopefully make better use of the term "to close".
This is an absolutely mechanical change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current taprio code operates on a very simplistic (and incorrect)
assumption: that egress scheduling for a traffic class can only take
place for the duration of the current interval, or i.o.w., it assumes
that at the end of each schedule entry, there is a "gate close" event
for all traffic classes.
As an example, traffic sent with the schedule below will be jumpy, even
though all 8 TC gates are open, so there is absolutely no "gate close"
event (effectively a transition from BIT(tc)==1 to BIT(tc)==0 in
consecutive schedule entries):
tc qdisc replace dev veth0 parent root taprio \
num_tc 2 \
map 0 1 \
queues 1@0 1@1 \
base-time 0 \
sched-entry S 0xff 4000000000 \
clockid CLOCK_TAI \
flags 0x0
This qdisc simply does not have what it takes in terms of logic to
*actually* compute the durations of traffic classes. Also, it does not
recognize the need to use this information on a per-traffic-class basis:
it always looks at entry->interval and entry->close_time.
This change proposes that each schedule entry has an array called
tc_gate_duration[tc]. This holds the information: "for how long will
this traffic class gate remain open, starting from *this* schedule
entry". If the traffic class gate is always open, that value is equal to
the cycle time of the schedule.
We'll also need to keep track, for the purpose of queueMaxSDU[tc]
calculation, what is the maximum time duration for a traffic class
having an open gate. This gives us directly what is the maximum sized
packet that this traffic class will have to accept. For everything else
it has to qdisc_drop() it in qdisc_enqueue().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current taprio software implementation is haunted by the shadow of the
igb/igc hardware model. It iterates over child qdiscs in increasing
order of TXQ index, therefore giving higher xmit priority to TXQ 0 and
lower to TXQ N. According to discussions with Vinicius, that is the
default (perhaps even unchangeable) prioritization scheme used for the
NICs that taprio was first written for (igb, igc), and we have a case of
two bugs canceling out, resulting in a functional setup on igb/igc, but
a less sane one on other NICs.
To the best of my understanding, taprio should prioritize based on the
traffic class, so it should really dequeue starting with the highest
traffic class and going down from there. We get to the TXQ using the
tc_to_txq[] netdev property.
TXQs within the same TC have the same (strict) priority, so we should
pick from them as fairly as we can. We can achieve that by implementing
something very similar to q->curband from multiq_dequeue().
Since igb/igc really do have TXQ 0 of higher hardware priority than
TXQ 1 etc, we need to preserve the behavior for them as well. We really
have no choice, because in txtime-assist mode, taprio is essentially a
software scheduler towards offloaded child tc-etf qdiscs, so the TXQ
selection really does matter (not all igb TXQs support ETF/SO_TXTIME,
says Kurt Kanzenbach).
To preserve the behavior, we need a capability bit so that taprio can
determine if it's running on igb/igc, or on something else. Because igb
doesn't offload taprio at all, we can't piggyback on the
qdisc_offload_query_caps() call from taprio_enable_offload(), but
instead we need a separate call which is also made for software
scheduling.
Introduce two static keys to minimize the performance penalty on systems
which only have igb/igc NICs, and on systems which only have other NICs.
For mixed systems, taprio will have to dynamically check whether to
dequeue using one prioritization algorithm or using the other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify taprio_dequeue_from_txq() by noticing that we can goto one call
earlier than the previous skb_found label. This is possible because
we've unified the treatment of the child->ops->dequeue(child) return
call, we always try other TXQs now, instead of abandoning the root
dequeue completely if we failed in the peek() case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future changes will refactor the TXQ selection procedure, and a lot of
stuff will become messy, the indentation of the bulk of the dequeue
procedure would increase, etc.
Break out the bulk of the function into a new one, which knows the TXQ
(child qdisc) we should perform a dequeue from.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the handling of an unlikely condition to not stop dequeuing
if taprio failed to dequeue the peeked skb in taprio_dequeue().
I've no idea when this can happen, but the only side effect seems to be
that the atomic_sub_return() call right above will have consumed some
budget. This isn't a big deal, since either that made us remain without
any budget (and therefore, we'd exit on the next peeked skb anyway), or
we could send some packets from other TXQs.
I'm making this change because in a future patch I'll be refactoring the
dequeue procedure to simplify it, and this corner case will have to go
away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't any code in the network stack which calls taprio_peek().
We only see qdisc->ops->peek() being called on child qdiscs of other
classful qdiscs, never from the generic qdisc code. Whereas taprio is
never a child qdisc, it is always root.
This snippet of a comment from qdisc_peek_dequeued() seems to confirm:
/* we can reuse ->gso_skb because peek isn't called for root qdiscs */
Since I've been known to be wrong many times though, I'm not completely
removing it, but leaving a stub function in place which emits a warning.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the subflow error report callback unconditionally
propagates the fallback subflow status to the owning msk.
If the msk is already orphaned, the above prevents the code
from correctly tracking the msk moving to the TCP_CLOSE state
and doing the appropriate cleanup.
All the above causes increasing memory usage over time and
sporadic self-tests failures.
There is a great deal of infrastructure trying to propagate
correctly the fallback subflow status to the owning mptcp socket,
e.g. via mptcp_subflow_eof() and subflow_sched_work_if_closed():
in the error propagation path we need only to cope with unorphaned
sockets.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/339
Fixes: 15cc104533 ("mptcp: deliver ssk errors to msk")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, in mptcp_pm_nl_create_listen_socket(), we need to
call the __mptcp_nmpc_socket() under the msk socket lock.
Note that as a side effect, mptcp_subflow_create_socket() needs a
'nested' lockdep annotation, as it will acquire the subflow (kernel)
socket lock under the in-kernel listener msk socket lock.
The current lack of locking is almost harmless, because the relevant
socket is not exposed to the user space, but in future we will add
more complexity to the mentioned helper, let's play safe.
Fixes: 1729cf186d ("mptcp: create the listening socket for new port")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to call the __mptcp_nmpc_socket(), and later subflow socket
access under the msk socket lock, or e.g. a racing connect() could
change the socket status under the hood, with unexpected results.
Fixes: 54635bd047 ("mptcp: add TCP_FASTOPEN_CONNECT socket option")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the peer closes all the existing subflows for a given
mptcp socket and later the application closes it, the current
implementation let it survive until the timewait timeout expires.
While the above is allowed by the protocol specification it
consumes resources for almost no reason and additionally
causes sporadic self-tests failures.
Let's move the mptcp socket to the TCP_CLOSE state when there are
no alive subflows at close time, so that the allocated resources
will be freed immediately.
Fixes: e16163b6e2 ("mptcp: refactor shutdown and close")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code fix a bug that sk->sk_txrehash gets its default enable
value from sysctl_txrehash only when the socket is a TCP listener.
We should have sysctl_txrehash to set the default sk->sk_txrehash,
no matter TCP, nor listerner/connector.
Tested by following packetdrill:
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 socket(..., SOCK_DGRAM, IPPROTO_UDP) = 4
// SO_TXREHASH == 74, default to sysctl_txrehash == 1
+0 getsockopt(3, SOL_SOCKET, 74, [1], [4]) = 0
+0 getsockopt(4, SOL_SOCKET, 74, [1], [4]) = 0
Fixes: 26859240e4 ("txhash: Add socket option to control TX hash rethink behavior")
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The > needs be >= to prevent an out of bounds access.
Fixes: de5ca4c385 ("net: sched: sch: Bounds check priority")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/Y+D+KN18FQI2DKLq@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEDs2BvajyNKlf9TJQvlAcSiqKBOgFAmPiWbYTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRC+UBxKKooE6HT3CACcKiUxmkFfS3I2MUCLt+spz2/4q3cG
+MX8m03fzSU8efdKN1ckUOmQfsPp2RNP7NSeI/Anu83oka40zFuejC/Dfg9V1SBF
EKD39VIWQTuPcYJP4GlxqKTkDHSVsA5iN/4vxzCFpp7C6LR3h2f0bTwj6SA44IvD
eatH6Vzr/Y1rG6Yj27hZzFpC8HXqHzaIcC1UJpODqNTmhrux/hskem0XqH68VQXK
FRi8K7xHgIs4MonamWGJj/oz1NkbEje3xvT4nZRkaMLgZY0prTQfJetSDaGwkBci
WJmqJ15PpBRedDpdTIeXkZK8U95BWt/gZEp28XwgkohP6A8DsilJFS7F
=Tcyi
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-6.2-20230207' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
can 2023-02-07
The patch is from Devid Antonio Filoni and fixes an address claiming
problem in the J1939 CAN protocol.
* tag 'linux-can-fixes-for-6.2-20230207' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: do not wait 250 ms if the same addr was already claimed
====================
Link: https://lore.kernel.org/r/20230207140514.2885065-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The callback devlink_nl_cmd_health_reporter_diagnose_doit() miss
devlink_fmsg_free(), which leads to memory leak.
Fix it by adding devlink_fmsg_free().
Fixes: e994a75fb7 ("devlink: remove reporter reference counting")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/1675698976-45993-1-git-send-email-moshe@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Chuck Lever