When adding a new vlan, if the underlying interface has no carrier,
then the newly added vlan interface should also have no carrier.
At present, this is not true - the newly added vlan is added with
carrier up. Fix by checking state of real device.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea: Fix synchronization between HW and SW send queue
When memory is added to / removed from a partition via the Memory DLPAR
mechanism, the eHEA driver has to do a couple of things to reflect the
memory change in its own IO address translation tables. This involves
stopping and restarting the HW queues.
During this operation, it is possible that HW and SW pointer into these
queues get out of sync. This results in a situation where packets that
are attached to a send queue are not transmitted immediately, but
delayed until further X packets have been put on the queue.
This patch detects such loss of synchronization, and resets the ehea
port when needed.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version to 1.52.53-4
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY locking is required between two ports for some external PHYs. Since
initialization was done in the common init function (called only on the
first port initialization) rather than in the port init function, there
was in fact no PHY locking between the ports.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct rds_rdma_notify contains a 32 bits hole on 64bit arches,
make sure it is zeroed before copying it to user.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since
commit 1dacc76d00
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Wed Jul 1 11:26:02 2009 +0000
net/compat/wext: send different messages to compat tasks
we had a race condition when setting and then
restoring frag_list. Eric attempted to fix it,
but the fix created even worse problems.
However, the original motivation I had when I
added the code that turned out to be racy is
no longer clear to me, since we only copy up
to skb->len to userspace, which doesn't include
the frag_list length. As a result, not doing
any frag_list clearing and restoring avoids
the race condition, while not introducing any
other problems.
Additionally, while preparing this patch I found
that since none of the remaining netlink code is
really aware of the frag_list, we need to use the
original skb's information for packet information
and credentials. This fixes, for example, the
group information received by compat tasks.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@kernel.org [2.6.31+, for 2.6.35 revert 1235f504aa]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"make headers_check" issued the following warning:
CHECK include/linux/netfilter (64 files)
usr/include/linux/netfilter/xt_ipvs.h:19: found __[us]{8,16,32,64} type without #include <linux/types.h>
Fix this by as suggested including linux/types.h.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: https://bugs.launchpad.net/bugs/619439
This ThinkPad model needs External Amplifier muted for audible playback,
so set the inv_eapd quirk for it.
Reported-and-tested-by: Dennis Bell <dennis.bell@parkerg.co.uk>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just added new codec ids. These are almost compatible with existing ones.
Signed-off-by: Charles Chin <Charles.Chin@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As noticed by Mikulas Patocka, the backoff macros don't
completely nop out for UP builds, we still get a
branch always and a delay slot nop.
Fix this by making the branch to the backoff spin loop
selective, then we can nop out the spin loop completely.
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple microoptimizations for sparc64 atomic functions:
Save one instruction by using a delay slot.
Use %g1 instead of %g7, because %g1 is written earlier.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix an Oops in the NFSv4 atomic open code
NFS: Fix the selection of security flavours in Kconfig
NFS: fix the return value of nfs_file_fsync()
rpcrdma: Fix SQ size calculation when memreg is FRMR
xprtrdma: Do not truncate iova_start values in frmr registrations.
nfs: Remove redundant NULL check upon kfree()
nfs: Add "lookupcache" to displayed mount options
NFS: allow close-to-open cache semantics to apply to root of NFS filesystem
SUNRPC: fix NFS client over TCP hangs due to packet loss (Bug 16494)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
USB HID: Add ID for eGalax Multitouch used in JooJoo tablet
HID: hiddev: fix memory corruption due to invalid intfdata
HID: hiddev: protect against disconnect/NULL-dereference race
HID: picolcd: correct ordering of framebuffer freeing
HID: picolcd: testing the wrong variable
For 5000 series of devices, use long monitor timer to check
stuck tx queues.
This modification apply to all the 5000 series including 5300 and others.
Cc: stable@kernel.org [2.6.35]
Reported-by: drago01 <drago01@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c96c31e499
"(drivers/net/wireless: Use wiphy_<level>)"
inadvertently changed some upper case words to
lower case. Restore the original case.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to make sure the eDP PLL is enabled before the pipes or planes,
so do it as part of the DP prepare mode set function.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We need to use I/O port instructions to access VGA registers on
Ironlake+, and it doesn't hurt on other platforms, so switch the VGA
plane disable function over to using them. Move it to init time as well
while we're at it, no need to repeatedly disable the VGA plane with
every mode set and DPMS event.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We should disable the panel first when shutting down an eDP link. And
when turning one on, the panel needs to be enabled before link training
or eDP I/O won't be enabled.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ironlake requires that we clear the reset panel bit during power
sequences and restore it afterwards. Uncondtionally add code to do that
since it should be harmless on SNB+.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix dummy inline stubs for trampoline-related functions when no
trampolines exist (until we get rid of the no-trampoline case
entirely.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <4C6C294D.3030404@zytor.com>
Fix the declaration of sys_execve() in asm-generic/syscalls.h to have
various consts applied to its pointers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cifs_find_smb_ses assumes that the vol->password field is a valid
pointer, but that's only the case if a password was passed in via
the options string. It's possible that one won't be if there is
no mount helper on the box.
Reported-by: diabel <gacek-2004@wp.pl>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
arch/ia64/kernel/process.c:636: error: conflicting types for ‘sys_execve’
commit d7627467b7
Make do_execve() take a const filename pointer
Missed the declaration of sys_execve in the ia64 asm/unistd.h (perhaps
because there is no reason for it to be there ... it might be a left over
from the COMPAT code?). Just delete the conflicting version.
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: brlock vfsmount_lock
fs: scale files_lock
lglock: introduce special lglock and brlock spin locks
tty: fix fu_list abuse
fs: cleanup files_lock locking
fs: remove extra lookup in __lookup_hash
fs: fs_struct rwlock to spinlock
apparmor: use task path helpers
fs: dentry allocation consolidation
fs: fix do_lookup false negative
mbcache: Limit the maximum number of cache entries
hostfs ->follow_link() braino
hostfs: dumb (and usually harmless) tpyo - strncpy instead of strlcpy
remove SWRITE* I/O types
kill BH_Ordered flag
vfs: update ctime when changing the file's permission by setfacl
cramfs: only unlock new inodes
fix reiserfs_evict_inode end_writeback second call
This fixes a build breakage introduced by commit 4c2ef25fe0 ("mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume")
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-mmc@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Parts of the build process were generating files outside the specified
O= directory, causing the build to fail on systems where the sources are
in a read only file system.
Fix it by using $(OUTPUT) on these locations.
Also check that $(OUTPUT) actually exists, just like the top level
kernel Makefile does. Otherwise the failure message emitted is
completely misleading.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20100817140841.0859362C03A@msa106.auone-net.jp>
Signed-off-by: Kusanagi Kouichi <slash@ac.auone-net.jp>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix build on POSIX shells
latencytop: Fix kconfig dependency warnings
perf annotate tui: Fix exit and RIGHT keys handling
tracing: Sanitize value returned from write(trace_marker, "...", len)
tracing/events: Convert format output to seq_file
tracing: Extend recordmcount to better support Blackfin mcount
tracing: Fix ring_buffer_read_page reading out of page boundary
tracing: Fix an unallocated memory access in function_graph
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: include sched.h in ColdFire/SPI driver
m68knommu: formatting of pointers in printk()
m68knommu: arch/m68k/include/asm/ide.h fix for nommu
* 'for-linus' of git://neil.brown.name/md:
md raid-1/10 Fix bio_rw bit manipulations again
md: provide appropriate return value for spare_active functions.
md: Notify sysfs when RAID1/5/10 disk is In_sync.
Update recovery_offset even when external metadata is used.
* 'merge-devicetree' of git://git.secretlab.ca/git/linux-2.6:
spi.h: missing kernel-doc notation, please fix
of: fix missing headers for of_address_to_resource() in MTD and SysACE drivers
of: Fix missing includes
ata: update for of_device to platform_device replacement
microblaze: Fix of: eliminate of_device->node and dev_archdata->{of,prom}_node
microblaze: Fix of/address: Merge all of the bus translation code
booting-without-of: Remove nonexistent chapters from TOC, fix numbering
This patch fixes machine crashes which occur when heavily exercising the
CPU hotplug codepaths on a 32-bit kernel. These crashes are caused by
AMD Erratum 383 and result in a fatal machine check exception. Here's
the scenario:
1. On 32-bit, the swapper_pg_dir page table is used as the initial page
table for booting a secondary CPU.
2. To make this work, swapper_pg_dir needs a direct mapping of physical
memory in it (the low mappings). By adding those low, large page (2M)
mappings (PAE kernel), we create the necessary conditions for Erratum
383 to occur.
3. Other CPUs which do not participate in the off- and onlining game may
use swapper_pg_dir while the low mappings are present (when leave_mm is
called). For all steps below, the CPU referred to is a CPU that is using
swapper_pg_dir, and not the CPU which is being onlined.
4. The presence of the low mappings in swapper_pg_dir can result
in TLB entries for addresses below __PAGE_OFFSET to be established
speculatively. These TLB entries are marked global and large.
5. When the CPU with such TLB entry switches to another page table, this
TLB entry remains because it is global.
6. The process then generates an access to an address covered by the
above TLB entry but there is a permission mismatch - the TLB entry
covers a large global page not accessible to userspace.
7. Due to this permission mismatch a new 4kb, user TLB entry gets
established. Further, Erratum 383 provides for a small window of time
where both TLB entries are present. This results in an uncorrectable
machine check exception signalling a TLB multimatch which panics the
machine.
There are two ways to fix this issue:
1. Always do a global TLB flush when a new cr3 is loaded and the
old page table was swapper_pg_dir. I consider this a hack hard
to understand and with performance implications
2. Do not use swapper_pg_dir to boot secondary CPUs like 64-bit
does.
This patch implements solution 2. It introduces a trampoline_pg_dir
which has the same layout as swapper_pg_dir with low_mappings. This page
table is used as the initial page table of the booting CPU. Later in the
bringup process, it switches to swapper_pg_dir and does a global TLB
flush. This fixes the crashes in our test cases.
-v2: switch to swapper_pg_dir right after entering start_secondary() so
that we are able to access percpu data which might not be mapped in the
trampoline page table.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <20100816123833.GB28147@aftab>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
A bug in the family-model-stepping matching code caused the presence of
errata to go undetected when OSVW was not used. This causes hangs on
some K8 systems because the E400 workaround is not enabled.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
LKML-Reference: <1282141190-930137-1-git-send-email-hans.rosenfeld@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
nilfs_discard_segment() doesn't wait for completion of discard
requests. This specifies BLKDEV_IFL_WAIT flag when calling
blkdev_issue_discard() in order to fix the sync failure.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Christoph Hellwig <hch@lst.de>
With some hardware combinations, the PCM interrupts are acknowledged
before the period boundary from the emu10k1 chip. The midlevel PCM code
gets confused and the playback stream is interrupted.
It seems that the interrupt processing shift by 2 samples is enough
to fix this issue. This default value does not harm other,
non-affected hardware.
More information: Kernel bugzilla bug#16300
[A copmile warning fixed by tiwai]
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fs: brlock vfsmount_lock
Use a brlock for the vfsmount lock. It must be taken for write whenever
modifying the mount hash or associated fields, and may be taken for read when
performing mount hash lookups.
A new lock is added for the mnt-id allocator, so it doesn't need to take
the heavy vfsmount write-lock.
The number of atomics should remain the same for fastpath rlock cases, though
code would be slightly slower due to per-cpu access. Scalability is not not be
much improved in common cases yet, due to other locks (ie. dcache_lock) getting
in the way. However path lookups crossing mountpoints should be one case where
scalability is improved (currently requiring the global lock).
The slowpath is slower due to use of brlock. On a 64 core, 64 socket, 32 node
Altix system (high latency to remote nodes), a simple umount microbenchmark
(mount --bind mnt mnt2 ; umount mnt2 loop 1000 times), before this patch it
took 6.8s, afterwards took 7.1s, about 5% slower.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fs: scale files_lock
Improve scalability of files_lock by adding per-cpu, per-sb files lists,
protected with an lglock. The lglock provides fast access to the per-cpu lists
to add and remove files. It also provides a snapshot of all the per-cpu lists
(although this is very slow).
One difficulty with this approach is that a file can be removed from the list
by another CPU. We must track which per-cpu list the file is on with a new
variale in the file struct (packed into a hole on 64-bit archs). Scalability
could suffer if files are frequently removed from different cpu's list.
However loads with frequent removal of files imply short interval between
adding and removing the files, and the scheduler attempts to avoid moving
processes too far away. Also, even in the case of cross-CPU removal, the
hardware has much more opportunity to parallelise cacheline transfers with N
cachelines than with 1.
A worst-case test of 1 CPU allocating files subsequently being freed by N CPUs
degenerates to contending on a single lock, which is no worse than before. When
more than one CPU are allocating files, even if they are always freed by
different CPUs, there will be more parallelism than the single-lock case.
Testing results:
On a 2 socket, 8 core opteron, I measure the number of times the lock is taken
to remove the file, the number of times it is removed by the same CPU that
added it, and the number of times it is removed by the same node that added it.
Booting: locks= 25049 cpu-hits= 23174 (92.5%) node-hits= 23945 (95.6%)
kbuild -j16 locks=2281913 cpu-hits=2208126 (96.8%) node-hits=2252674 (98.7%)
dbench 64 locks=4306582 cpu-hits=4287247 (99.6%) node-hits=4299527 (99.8%)
So a file is removed from the same CPU it was added by over 90% of the time.
It remains within the same node 95% of the time.
Tim Chen ran some numbers for a 64 thread Nehalem system performing a compile.
throughput
2.6.34-rc2 24.5
+patch 24.9
us sys idle IO wait (in %)
2.6.34-rc2 51.25 28.25 17.25 3.25
+patch 53.75 18.5 19 8.75
So significantly less CPU time spent in kernel code, higher idle time and
slightly higher throughput.
Single threaded performance difference was within the noise of microbenchmarks.
That is not to say penalty does not exist, the code is larger and more memory
accesses required so it will be slightly slower.
Cc: linux-kernel@vger.kernel.org
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
lglock: introduce special lglock and brlock spin locks
This patch introduces "local-global" locks (lglocks). These can be used to:
- Provide fast exclusive access to per-CPU data, with exclusive access to
another CPU's data allowed but possibly subject to contention, and to provide
very slow exclusive access to all per-CPU data.
- Or to provide very fast and scalable read serialisation, and to provide
very slow exclusive serialisation of data (not necessarily per-CPU data).
Brlocks are also implemented as a short-hand notation for the latter use
case.
Thanks to Paul for local/global naming convention.
Cc: linux-kernel@vger.kernel.org
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
tty: fix fu_list abuse
tty code abuses fu_list, which causes a bug in remount,ro handling.
If a tty device node is opened on a filesystem, then the last link to the inode
removed, the filesystem will be allowed to be remounted readonly. This is
because fs_may_remount_ro does not find the 0 link tty inode on the file sb
list (because the tty code incorrectly removed it to use for its own purpose).
This can result in a filesystem with errors after it is marked "clean".
Taking idea from Christoph's initial patch, allocate a tty private struct
at file->private_data and put our required list fields in there, linking
file and tty. This makes tty nodes behave the same way as other device nodes
and avoid meddling with the vfs, and avoids this bug.
The error handling is not trivial in the tty code, so for this bugfix, I take
the simple approach of using __GFP_NOFAIL and don't worry about memory errors.
This is not a problem because our allocator doesn't fail small allocs as a rule
anyway. So proper error handling is left as an exercise for tty hackers.
[ Arguably filesystem's device inode would ideally be divorced from the
driver's pseudo inode when it is opened, but in practice it's not clear whether
that will ever be worth implementing. ]
Cc: linux-kernel@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fs: cleanup files_lock locking
Lock tty_files with a new spinlock, tty_files_lock; provide helpers to
manipulate the per-sb files list; unexport the files_lock spinlock.
Cc: linux-kernel@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fs: remove extra lookup in __lookup_hash
Optimize lookup for create operations, where no dentry should often be
common-case. In cases where it is not, such as unlink, the added overhead
is much smaller than the removed.
Also, move comments about __d_lookup racyness to the __d_lookup call site.
d_lookup is intuitive; __d_lookup is what needs commenting. So in that same
vein, add kerneldoc comments to __d_lookup and clean up some of the comments:
- We are interested in how the RCU lookup works here, particularly with
renames. Make that explicit, and point to the document where it is explained
in more detail.
- RCU is pretty standard now, and macros make implementations pretty mindless.
If we want to know about RCU barrier details, we look in RCU code.
- Delete some boring legacy comments because we don't care much about how the
code used to work, more about the interesting parts of how it works now. So
comments about lazy LRU may be interesting, but would better be done in the
LRU or refcount management code.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fs: fs_struct rwlock to spinlock
struct fs_struct.lock is an rwlock with the read-side used to protect root and
pwd members while taking references to them. Taking a reference to a path
typically requires just 2 atomic ops, so the critical section is very small.
Parallel read-side operations would have cacheline contention on the lock, the
dentry, and the vfsmount cachelines, so the rwlock is unlikely to ever give a
real parallelism increase.
Replace it with a spinlock to avoid one or two atomic operations in typical
path lookup fastpath.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Phil Oester