It doesn't make sense to set the RTC to a default value at probe time. Let
the core handle invalid date and time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
And stop trying to get a reference on the submodule, procfs code deals
with release after an unloaded module and thus removed proc entry.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
RTC driver should not be aware of the PWR registers offset and bits
position. Furthermore, we can imagine that DBP relative register and bit
mask could change depending on the SoC.
So this patch introduces 2 parameters, dbp_reg and dbp_mask, allowing to
get PWR_CR and PWR_CR_DBP from device tree. And it prepares next RTC
version, backup domain write protection is disabled only if needed.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
RTC alarm interrupt is active high and already configured by device tree.
So remove IRQF_TRIGGER_RISING from driver.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The tps6586x use a 64-bit 'epoch_start' value, but then computes that
value using an 'mktime()', which has a smaller range and overflows
in 2106 at the latest. As both the hardware and the subsystem interface
support wider than 32-bit ranges for rtc times here, let's change all
the operations on 'seconds' to time64_t.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The loongson1 platform is 32-bit, so storing a time value in 32 bits
suffers from limited range. In this case it is likely to be correct
until 2106, but it's better to avoid the limitation and just use
the time64_t based mktime64() and rtc_time64_to_tm() interfaces.
The hardware uses a 32-bit year number, and time64_t can cover that
entire range.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This driver uses mktime() and rtc_time_to_tm() to convert between time
values. This works fine on 64-bit kernels over the whole supported
range, and the vr41xx chip is a 64-bit MIPS implementation, but it is
inconsistent because it doesn't do the same thing on 32-bit kernels that
overflow in 2106 or 2038.
Changing it to use mktime64/rtc_time64_to_tm() should have no visible
impact on vr41xx but gets us closer to removing the 32-bit interfaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The SC27xx RTC can support dates from 1970-01-01 00:00:00 to 2149-06-06
23:59:59.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This is a preparation patch, changing to use devm_rtc_allocate_device()
that can allow driver to set 'range_max' and 'range_min' for the RTC
device.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com> (for zynqmp)
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The OPAL RTC driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, up to 50 seconds have been observed here when RTC stops
responding (BMC reboot can do it).
Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.
Fixes: 628daa8d5a ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use ACPI for RTC Alarm only for Intel platforms
1. with Low Power S0 support
2. with HPET RTC emulation enabled
3. no earlier than 2015
Note that, during the test, it is found that this patch
1. works in 4.15-rc kernel
2. hangs the platform after suspend-to-idle for 2 or 3 times, in 4.15.0
3. works again in 4.16-rc3 kernel.
4. works in the latest 4.15.12 stable kernel.
Thus although this patch breaks 4.15.0 kernel for some unknown reason,
still, it is safe for both upstream and backport.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Previously, the RTC alarm is acknowledged either by the cmos rtc irq
handler, or by the hpet rtc irq handler.
When using ACPI RTC Fixed event as the RTC alarm, the RTC alarm is
acknowledged by the ACPI RTC event handler, as addressed in the previous
patch.
But, when resume from suspend-to-ram (ACPI S3), the ACPI SCI is cleared
right after resume, thus the ACPI RTC event handler is not invoked at all,
results in the RTC Alarm unacknowledged.
Handle this by comparing the current time and the RTC Alarm time in the
rtc_cmos driver .resume() callback
1. Assume the wakeup event has already been fired if the RTC Alarm time
is earlier than/equal to the current time, and ACK the RTC Alarm.
2. Assume the wakeup event has not been fired if the RTC Alarm time
is later than current time, and re-arm it if needed.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It's found that the HPET timer prevents the platform from entering
Low Power S0 on some new Intel platforms.
This means that
1. users can still use RTC wake Alarm for suspend-to-idle, but the system
never enters Low Power S0, which is a waste of power.
or
2. if users want to put the system into Low Power S0, they can not use
RTC as the wakeup source.
To fix this, we need to stop using the HPET timer for wake alarm.
But disabling CONFIG_HPET_EMULATE_RTC is not an option because HPET
emulates PIT at the same time, and this is needed on some of these
platforms.
Thus, introduce a new mode (use_acpi_alarm) to the rtc_cmos driver,
so that, even with CONFIG_HPET_EMULATE_RTC enabled, it's still possible to
use ACPI SCI for RTC Alarm, including UIE/AIE/wkalrm, instead of HPET.
Only necessary changes are made for the new "use_acpi_alarm" mode, including
1. drop all the calls to HPET emulation code, including the HPET irq
handler for rtc interrupt.
2. enabling/disabling ACPI RTC Fixed event upon RTC UIE/AIE request.
3. acknowledge the RTC Alarm in ACPI RTC Fixed event handler.
There is no functional change made in this patch if the new mode is not
enabled.
Note: this "use_acpi_alarm" mode is made based on the assumption that
ACPI RTC Fixed event is reliable both at runtime and during system wakeup.
And this has been verified on a couple of platforms I have, including
a MS Surface Pro 4 (SKL), a Lenovo Yoga 900 (SKL), and a HP 9360 (KBL).
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The core driver should create and manage irq mappings instead of
leaf drivers. This patch change to pass irq domain to
devm_mfd_add_devices() and it will create mapping for irq resources
automatically. And remove irq mapping in rtc driver since this has
been done in core driver.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Subsystem:
- Add tracepoints
- Rework of the RTC/nvmem API to allow drivers to discard struct nvmem_config
after registration
- New range API, drivers can now expose the useful range of the RTC
- New offset API the core is now able to add an offset to the RTC time,
modifying the supported range.
- Multiple rtc_time64_to_tm fixes
- Handle time_t overflow on 32 bit platforms in the core instead of letting
drivers do crazy things.
- remove rtc_control API
New driver:
- Intersil ISL12026
Drivers:
- Drivers exposing the RTC non volatile memory have been converted to use nvmem
- Removed useless time and date validation
- Removed an indirection pattern that was a cargo cult from ancient drivers
- Removed VLA usage
- Fixed a possible race condition in probe functions
- AB8540 support is dropped from ab8500
- pcf85363 now has alarm support
-----BEGIN PGP SIGNATURE-----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=l9i8
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"This contains a few series that have been in preparation for a while
and that will help systems with RTCs that will fail in 2038, 2069 or
2100.
Subsystem:
- Add tracepoints
- Rework of the RTC/nvmem API to allow drivers to discard struct
nvmem_config after registration
- New range API, drivers can now expose the useful range of the RTC
- New offset API the core is now able to add an offset to the RTC
time, modifying the supported range.
- Multiple rtc_time64_to_tm fixes
- Handle time_t overflow on 32 bit platforms in the core instead of
letting drivers do crazy things.
- remove rtc_control API
New driver:
- Intersil ISL12026
Drivers:
- Drivers exposing the RTC non volatile memory have been converted to
use nvmem
- Removed useless time and date validation
- Removed an indirection pattern that was a cargo cult from ancient
drivers
- Removed VLA usage
- Fixed a possible race condition in probe functions
- AB8540 support is dropped from ab8500
- pcf85363 now has alarm support"
* tag 'rtc-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (128 commits)
rtc: snvs: Fix usage of snvs_rtc_enable
rtc: mt7622: fix module autoloading for OF platform drivers
rtc: isl12022: use true and false for boolean values
rtc: ab8500: Drop AB8540 support
rtc: remove a warning during scripts/kernel-doc step
rtc: 88pm860x: remove artificial limitation
rtc: 88pm80x: remove artificial limitation
rtc: st-lpc: remove artificial limitation
rtc: mrst: remove artificial limitation
rtc: mv: remove artificial limitation
rtc: hctosys: Ensure system time doesn't overflow time_t
parisc: time: stop validating rtc_time in .read_time
rtc: pcf85063: fix clearing bits in pcf85063_start_clock
rtc: at91sam9: Set name of regmap_config
rtc: s5m: Remove VLA usage
rtc: s5m: Move enum from rtc.h to rtc-s5m.c
rtc: remove VLA usage
rtc: Add useful timestamp definitions
rtc: Add one offset seconds to expand RTC range
rtc: Factor out the RTC range validation into rtc_valid_range()
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
commit 179a502f8c ("rtc: snvs: add Freescale rtc-snvs driver") introduces
the SNVS RTC driver with a function snvs_rtc_enable().
snvs_rtc_enable() can return an error on the enable path however this
driver does not currently trap that failure on the probe() path and
consequently if enabling the RTC fails we encounter a later error spinning
forever in rtc_write_sync_lp().
[ 36.093481] [<c010d630>] (__irq_svc) from [<c0c2e9ec>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[ 36.102122] [<c0c2e9ec>] (_raw_spin_unlock_irqrestore) from [<c072e32c>] (regmap_read+0x4c/0x5c)
[ 36.110938] [<c072e32c>] (regmap_read) from [<c085d0f4>] (rtc_write_sync_lp+0x6c/0x98)
[ 36.118881] [<c085d0f4>] (rtc_write_sync_lp) from [<c085d160>] (snvs_rtc_alarm_irq_enable+0x40/0x4c)
[ 36.128041] [<c085d160>] (snvs_rtc_alarm_irq_enable) from [<c08567b4>] (rtc_timer_do_work+0xd8/0x1a8)
[ 36.137291] [<c08567b4>] (rtc_timer_do_work) from [<c01441b8>] (process_one_work+0x28c/0x76c)
[ 36.145840] [<c01441b8>] (process_one_work) from [<c01446cc>] (worker_thread+0x34/0x58c)
[ 36.153961] [<c01446cc>] (worker_thread) from [<c014aee4>] (kthread+0x138/0x150)
[ 36.161388] [<c014aee4>] (kthread) from [<c0107e14>] (ret_from_fork+0x14/0x20)
[ 36.168635] rcu_sched kthread starved for 2602 jiffies! g496 c495 f0x2 RCU_GP_WAIT_FQS(3) ->state=0x0 ->cpu=0
[ 36.178564] rcu_sched R running task 0 8 2 0x00000000
[ 36.185664] [<c0c288b0>] (__schedule) from [<c0c29134>] (schedule+0x3c/0xa0)
[ 36.192739] [<c0c29134>] (schedule) from [<c0c2db80>] (schedule_timeout+0x78/0x4e0)
[ 36.200422] [<c0c2db80>] (schedule_timeout) from [<c01a7ab0>] (rcu_gp_kthread+0x648/0x1864)
[ 36.208800] [<c01a7ab0>] (rcu_gp_kthread) from [<c014aee4>] (kthread+0x138/0x150)
[ 36.216309] [<c014aee4>] (kthread) from [<c0107e14>] (ret_from_fork+0x14/0x20)
This patch fixes by parsing the result of rtc_write_sync_lp() and
propagating both in the probe and elsewhere. If the RTC doesn't start we
don't proceed loading the driver and don't get into this loop mess later
on.
Fixes: 179a502f8c ("rtc: snvs: add Freescale rtc-snvs driver")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It's required to create a modules.alias via MODULE_DEVICE_TABLE helper
for the OF platform driver. Otherwise, module autoloading cannot work.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
During compilation using W=1 one would get:
drivers/rtc/systohc.c:11: info: Scanning doc for rtc_set_ntp_time
drivers/rtc/systohc.c:23: warning: bad line: (
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 88pm860x supports time up to 2106 (it is a 32 bit counter). Also, the
year will never be before 1970 as the RTC core forbids that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 88pm80x supports time up to 2106 (it is a 32 bit counter). Also, the
year will never be before 1970 as the RTC core forbids that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The LPC RTC supports dates way beyond 2038, don't limit it artificially as
the kernel handles dates after 2038 properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Dates after 2038 actually fit on 32 bits. The counter will overflow in
2106. Also, it is bad practice to reset the RTC to a default value.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On 32bit platforms, time_t is still a signed 32bit long. If it is
overflowed, userspace and the kernel cant agree on the current system time.
This causes multiple issues, in particular with systemd:
https://github.com/systemd/systemd/issues/1143
A good workaround is to simply avoid using hctosys which is something I
greatly encourage as the time is better set by userspace.
However, many distribution enable it and use systemd which is rendering the
system unusable in case the RTC holds a date after 2038 (and more so after
2106). Many drivers have workaround for this case and they should be
eliminated so there is only one place left to fix when userspace is able to
cope with dates after the 31bit overflow.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The blackfin architecture is getting removed, so this one is
now obsolete.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The tile architecture is getting removed, so this driver is
no longer needed.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some functions definitions have either the initial open brace and/or
the closing brace outside of column 1.
Move those braces to column 1.
This allows various function analyzers like gnu complexity to work
properly for these modified functions.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bit clear operation was missing ~
Signed-off-by: Michael McCormick <michael.mccormick@enatel.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We are now allowing to register debugfs without a valid device, and not
having a valid name will end up using "dummy*" to create debugfs dir.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In preparation to enabling -Wvla, remove VLAs and replace them
with fixed-length arrays instead.
>From a security viewpoint, the use of Variable Length Arrays can be
a vector for stack overflow attacks. Also, in general, as the code
evolves it is easy to lose track of how big a VLA can get. Thus, we
can end up having segfaults that are hard to debug.
Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move this enum to rtc-s5m.c once it is meaningless to others drivers [1].
[1] https://marc.info/?l=linux-rtc&m=152060068925948&w=2
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In preparation to enabling -Wvla, remove VLA and replace it
with a fixed-length array instead.
>From a security viewpoint, the use of Variable Length Arrays can be
a vector for stack overflow attacks. Also, in general, as the code
evolves it is easy to lose track of how big a VLA can get. Thus, we
can end up having segfaults that are hard to debug.
Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
From our investigation for all RTC drivers, 1 driver will be expired before
year 2017, 7 drivers will be expired before year 2038, 23 drivers will be
expired before year 2069, 72 drivers will be expired before 2100 and 104
drivers will be expired before 2106. Especially for these early expired
drivers, we need to expand the RTC range to make the RTC can still work
after the expired year.
So we can expand the RTC range by adding one offset to the time when reading
from hardware, and subtracting it when writing back. For example, if you have
an RTC that can do 100 years, and currently is configured to be based in
Jan 1 1970, so it can represents times from 1970 to 2069. Then if you change
the start year from 1970 to 2000, which means it can represents times from
2000 to 2099. By adding or subtracting the offset produced by moving the wrap
point, all times between 1970 and 1999 from RTC hardware could get interpreted
as times from 2070 to 2099, but the interpretation of dates between 2000 and
2069 would not change.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC range validation code can be factored into rtc_valid_range()
function to avoid duplicate code.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add a way for drivers to inform the core of the supported date/time range.
The core can then check whether the date/time or alarm is in the range
before calling ->set_time, ->set_mmss or ->set_alarm. It returns -ERANGE
when the time is out of range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix possible race condition.
It is not allowed to return with an error code after RTC is registered.
Suggested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Denis Osterland <Denis.Osterland@diehl.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The interrupt handler got enabled very early. If the interrupt cause is
triggering immediately before the context is fully prepared. This can
lead to undefined behaviour. Therefor we move the interrupt enable code
to the end of the probe function.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Denis Osterland <Denis.Osterland@diehl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since accessing a Chrome OS EC based rtc is a slow operation, there is a
race window where if the alarm is set for the next second and the second
ticks over right before calculating the alarm offset.
In this case the current driver is setting a 0-second alarm, which would
be considered as disabling alarms by the EC(EC_RTC_ALARM_CLEAR).
This breaks, e.g., hwclock which relies on RTC_UIE_ON ->
rtc_update_irq_enable(), which sets a 1-second alarm and expects it to
fire an interrupt.
So return -ETIME when the alarm is in the past, follow __rtc_set_alarm().
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In order to set time in rtc, need to disable
rtc hw before writing into rtc registers.
Also fixes disabling of alarm while setting
rtc time.
Signed-off-by: Mohit Aggarwal <maggarwa@codeaurora.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This config select's MFD_SYSCON, but does not depend on HAS_IOMEM.
Compile testing on architecture without HAS_IOMEM causes "unmet
direct dependencies" in Kconfig phase.
Detected by "make ARCH=score allyesconfig".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The probe function must not fail after rtc_register_device. Also, rename
the nvmem device so it is easily identifiable in /sys/bus/nvmem.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ISL12026 is a combination RTC and EEPROM device with I2C
interface. The standard RTC driver interface is provided. The EEPROM
is accessed via the NVMEM interface.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The HW default is one tick per second, however instead of assuming this,
lets make sure the waketimer is actually one tick per second before
arming the alarm.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The current correction for leap years will fail in 3477. 3476-12-31 being
3477-01-00 because this is 366 leap years after 1970 and 3477 isn't a leap
year.
Fix that by looping over until days is positive or zero.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch fixes a bug, that prevents the Allwinner A83T and the A80
from a successful boot.
The bug is there since v4.16-rc1 and appeared after the clk branch was
merged.
You can find the shortend trace below:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
pgd = (ptrval)
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 49 Comm: kworker/0:1 Not tainted 4.15.0-10190-gb89e32ccd1be #2
Hardware name: Allwinner sun8i Family
Workqueue: events deferred_probe_work_func
PC is at clk_hw_get_rate+0x0/0x34
LR is at ac100_clkout_determine_rate+0x48/0x19c
[ ... ]
(clk_hw_get_rate) from (ac100_clkout_determine_rate+0x48/0x19c)
(ac100_clkout_determine_rate) from (clk_core_set_rate_nolock+0x3c/0x1a0)
(clk_core_set_rate_nolock) from (clk_set_rate+0x30/0x88)
(clk_set_rate) from (of_clk_set_defaults+0x200/0x364)
(of_clk_set_defaults) from (platform_drv_probe+0x18/0xb0)
To fix that bug, we first check if the return of the
clk_hw_get_parent_by_index is non zero. If it is zero we skip that
clock parent.
The BUG report could be found here: https://lkml.org/lkml/2018/2/10/198
Fixes: 04940631b8 ("rtc: ac100: Add clk output support")
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As per 8.2.6 Setting and reading the time in RTC mode, first stop the clok,
then reset it before setting the date and time registers. Finally, start
the clock.
This uses register address wrap around from 0x2f to 0x00 for efficiency.
This allows to set the clock with a millisecond accuracy (drift is not
corrected in this example):
RTC System
1325388767 1325388767.000029180
1325388768 1325388768.000018362
1325388769 1325388769.000006544
1325388770 1325388769.999992725
1325388771 1325388770.999974544
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
m41t80_get_datetime and m41t80_set_datetime are only used after casting dev
to an i2c_client. Remove that useless indirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Without CONFIG_RTC_DRV_M41T80_WDT the compiler complains:
|drivers/rtc/rtc-m41t80.c:76 ‘m41t80_rtc_mutex’ defined but not used [-Wunused-variable]
Move the variable to the block where it is used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
pcf85063_get_datetime and pcf85063_set_datetime are only used after casting
dev to an i2c_client. Remove that useless indirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
max6900_i2c_read_time and max6900_i2c_set_time are only used after casting
dev to an i2c_client. Remove that useless indirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
rs5c372_get_datetime and rs5c372_set_datetime are only used after casting
dev to an i2c_client. Remove that useless indirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not necessary to print a message when the time is invalid as
userspace will already get an error (and an optional dev_dbg message).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
s35390a_set_datetime, s35390a_get_datetime, s35390a_set_alarm and
s35390a_read_alarm are only used after casting dev to an i2c_client. Remove
that useless indirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not necessary to print a message when the time is invalid as
userspace will already get an error (and an optional dev_dbg message).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The probe function is not allowed to fail after registering the RTC because
the following may happen:
CPU0: CPU1:
sys_load_module()
do_init_module()
do_one_initcall()
cmos_do_probe()
rtc_device_register()
__register_chrdev()
cdev->owner = struct module*
open("/dev/rtc0")
rtc_device_unregister()
module_put()
free_module()
module_free(mod->module_core)
/* struct module *module is now
freed */
chrdev_open()
spin_lock(cdev_lock)
cdev_get()
try_module_get()
module_is_live()
/* dereferences already
freed struct module* */
Switch to devm_rtc_allocate_device/rtc_register_device to register the rtc
as late as possible.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
At probe time, printing a message when the time is invalid doesn't have
much value. Also, as the comment suggest, this is a leftover from
development wherhe this was used to set the RTc to a default time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not necessary to print a message when the time is invalid as
userspace will already get an error (and an optional dev_dbg message).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not necessary to print a message when the time is invalid as
userspace will already get an error (and an optional dev_dbg message).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not necessary to print a message when the time is invalid as
userspace will already get an error (and an optional dev_dbg message).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not necessary to print a message when the time is invalid as
userspace will already get an error (and an optional dev_dbg message).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always validating the rtc_time struct before calling
.set_time. It is not necessary to do it again in .set_time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always validating the rtc_time struct before calling
.set_time or .set_alarm. It is not necessary to do it again.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always validating the rtc_time struct before calling
.set_time or .set_alarm. It is not necessary to do it again.
Also, rtc_time_to_tm never generates an invalid rtc_tm (it can be out of
range though).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
isl12022_get_datetime and isl12022_set_datetime are only used after casting
dev to an i2c_client. Remove that useless indirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
rtc_time64_to_tm never generates an invalid tm. It is not necessary to
validate it. Also, the RTC core is always calling rtc_valid_tm after the
read_time callback.
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it before returning from the callback.
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Returning a valid time when the time is invalid is a bad practice, because
then userspace is not able to react on the information. Also, it doesn't
make sense to return epoch because it is already the default time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Returning a valid time when the time is invalid is a bad practice, because
then userspace is not able to react on the information. Also, it doesn't
make sense to return epoch because it is already the default time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Setting the rtc to a valid time when the time is invalid is a bad practice,
because then userspace doesn't know it shouldn't trust the RTC.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Returning a valid time when the time is invalid is a bad practice, because
then userspace is not able to react on the information. Also, it doesn't
make sense to return epoch because it is already the default time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Returning a valid time when the time is invalid is a bad practice, because
then userspace is not able to react on the information. Also, it doesn't
make sense to return epoch because it is already the default time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The shifting of buf[5] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. If
the top bit of buf[5] is set then all then all the upper bits sec
end up as also being set because of the sign-extension. Fix this by
casting buf[5] to an unsigned long before the shift.
Detected by CoverityScan, CID#1465292 ("Unintended sign extension")
Fixes: 0e1492330c ("rtc: add rtc-tx4939 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After successful
sr = isl1208_i2c_set_regs(client, 0, regs, ISL1208_RTC_SECTION_LEN);
sr will be 0.
As a result
sr = i2c_smbus_write_byte_data(client, ISL1208_REG_SR,
sr & ~ISL1208_REG_SR_WRTC);
is equal to
sr = i2c_smbus_write_byte_data(client, ISL1208_REG_SR, 0);
which clears all flags in SR.
Add an additional read of SR, to have value of SR in sr again.
Signed-off-by: Denis Osterland <Denis.Osterland@diehl.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of adding a binary sysfs attribute from the driver, use the core to
register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The probe function is not allowed to fail after registering the RTC. Call
rtc_register_device() at the end.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The rtc-tx4939 driver now compiles correctly on other architectures, add
COMPILE_TEST to improve code coverage.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Copy RTC definitions from arch/mips/include/asm/txx9/tx4939.h to the RTC
driver so it doesn't depend on arch/mips anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of adding a binary sysfs attribute from the driver, use the core to
register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The probe function is not allowed to fail after registering the RTC. Call
rtc_register_device() at the end.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Currently, the IRQs are disabled when the rtc driver is removed (e.g. when
shutting down the platform).
This means that the RTC will be unable to wakeup the platform.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of adding a binary sysfs attribute from the driver, use the core to
register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The probe function is not allowed to fail after registering the RTC because
the following may happen:
CPU0: CPU1:
sys_load_module()
do_init_module()
do_one_initcall()
cmos_do_probe()
rtc_device_register()
__register_chrdev()
cdev->owner = struct module*
open("/dev/rtc0")
rtc_device_unregister()
module_put()
free_module()
module_free(mod->module_core)
/* struct module *module is now
freed */
chrdev_open()
spin_lock(cdev_lock)
cdev_get()
try_module_get()
module_is_live()
/* dereferences already
freed struct module* */
Switch to devm_rtc_allocate_device/rtc_register_device to register the rtc
as late as possible.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of adding a binary sysfs attribute from the driver (which suffers
from a race condition as the attribute appears after the device), use the
core to register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of adding a binary sysfs attribute from the driver, use the
core to register an nvmem device. This allows to use the in-kernel
interface to access the nvram.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The probe function is not allowed to fail after registering the RTC because
the following may happen:
CPU0: CPU1:
sys_load_module()
do_init_module()
do_one_initcall()
cmos_do_probe()
rtc_device_register()
__register_chrdev()
cdev->owner = struct module*
open("/dev/rtc0")
rtc_device_unregister()
module_put()
free_module()
module_free(mod->module_core)
/* struct module *module is now
freed */
chrdev_open()
spin_lock(cdev_lock)
cdev_get()
try_module_get()
module_is_live()
/* dereferences already
freed struct module* */
Switch to devm_rtc_allocate_device/rtc_register_device to register the rtc
as late as possible.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Currently, the IRQs are disabled when the rtc driver is removed (e.g. when
shutting down the platform).
This means that the RTC will be unable to wakeup the platform.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of adding a binary sysfs attribute from the driver (which suffers
from a race condition as the attribute appears after the device), use the
core to register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of adding a binary sysfs attribute from the driver (which suffers
from a race condition as the attribute appears after the device), use the
core to register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of adding a binary sysfs attribute from the driver (which suffers
from a race condition as the attribute appears after the device), use the
core to register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
A documented ABI already exists to get information about the alarm. It is
the only one that is used.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Because nvmem_config is only used and copied at nvmem registration, remove
it from struct rtc_device.
All the rtc drivers using nvmem are now calling rtc_nvmem_register
directly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The probe function is not allowed to fail after registering the RTC. Call
rtc_register_device() at the end.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call rtc_nvmem_register instead of letting the core do it and stop using
the nvmem_config member of struct rtc_device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call rtc_nvmem_register instead of letting the core do it and stop using
the nvmem_config member of struct rtc_device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call rtc_nvmem_register instead of letting the core do it and stop using
the nvmem_config member of struct rtc_device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move m48t86_nvmem_cfg to the stack of m48t86_rtc_probe. This results in a
very small code size reduction and make it safer on systems with two
similar RTCs:
text data bss dec hex filename
1733 164 0 1897 769 drivers/rtc/rtc-m48t86.o.before
1793 100 0 1893 765 drivers/rtc/rtc-m48t86.o.after
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call rtc_nvmem_register instead of letting the core do it and stop using
the nvmem_config member of struct rtc_device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move ds1511_nvmem_cfg to the stack of ds1511_rtc_probe. This results in a
very small code size reduction and make it safer on systems with two
similar RTCs:
text data bss dec hex filename
2128 164 4 2296 8f8 drivers/rtc/rtc-ds1511.o.before
2175 100 4 2279 8e7 drivers/rtc/rtc-ds1511.o.after
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call rtc_nvmem_register instead of letting the core do it and stop using
the nvmem_config member of struct rtc_device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Avoid allocating memory for struct nvmem_config as it is only necessary at
the nvmem registration.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call rtc_nvmem_register instead of letting the core do it and stop using
the nvmem_config member of struct rtc_device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call rtc_nvmem_register instead of letting the core do it and stop using
the nvmem_config member of struct rtc_device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Export rtc_nvmem_register() so it can be called from drivers instead of
only the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Switch the parent of the nvmem device to the parent of the rtc device so it
can be registered before the RTC.
This is a small change in the ABI as the nvmem moves out of the
/sys/class/rtc/rtcX folder to be under the parent device folder (that is
where the previous nvram files where registered).
However, it is still available under its correct location,
/sys/bus/nvmem/devices which is the one that should be used by userspace
applications.
The other benefit is that the nvmem device can stay registered even if the
rtc registration fails. Or it is possible to not register the rtc if the
nvmem registration failed.
Finally, it makes a lot of sense for devices that actually have different
i2c or spi addresses for the RTC and the EEPROM. That is basically how it
would end up when using MFD or even completely separate devices.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Make rtc_nvmem_register return -EBUSY when an nvmem is already registered
for that RTC.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In case of error, make rtc_nvmem_register() able to return an error value
to its caller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
To be able to remove nvmem_config from struct rtc_device, pass it as a
parameter to rtc_nvmem_register.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pointe bp is being initialized and this value is never read, it
is being updated to the same value later just before it is going to
be used. Remove the initialization as it is never read and keep
the setting of bp closer to the use of bp.
Cleans up clang warnings:
drivers/rtc/rtc-ds1302.c:115:7: warning: Value stored to 'bp' during
its initialization is never read
drivers/rtc/rtc-ds1302.c:46:7: warning: Value stored to 'bp' during
its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix the following warning in MIPS allmodconfig by adding a
MODULE_LICENSE() at the end of rtc-goldfish.c, based on the file header
comment which says GNU General Public License version 2:
WARNING: modpost: missing MODULE_LICENSE() in drivers/rtc/rtc-goldfish.o
Fixes: f22d9cdcb5 ("rtc: goldfish: Add RTC driver for Android emulator")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Miodrag Dinic <miodrag.dinic@mips.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: linux-rtc@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
If we convert one large time values to rtc_time, in the original formula
'days * 86400' can be overflowed in 'unsigned int' type to make the formula
get one incorrect remain seconds value. Thus we can use div_s64_rem()
function to avoid this situation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It will be more helpful to add some tracepoints to track RTC actions when
debugging RTC driver. Below sample is that we set/read the RTC time, then
set 2 alarms, so we can see the trace logs:
set/read RTC time:
kworker/0:1-67 [000] 21.814245: rtc_set_time: UTC (1510301580) (0)
kworker/0:1-67 [000] 21.814312: rtc_read_time: UTC (1510301580) (0)
set the first alarm timer:
kworker/0:1-67 [000] 21.829238: rtc_timer_enqueue: RTC timer:(ffffffc15eb49bc8) expires:1510301700000000000 period:0
kworker/0:1-67 [000] 22.018279: rtc_set_alarm: UTC (1510301700) (0)
set the second alarm timer:
kworker/0:1-67 [000] 22.230284: rtc_timer_enqueue: RTC timer:(ffffff80088e6430) expires:1510301820000000000 period:0
the first alarm timer was expired:
kworker/0:1-67 [000] 145.155584: rtc_timer_dequeue: RTC timer:(ffffffc15eb49bc8) expires:1510301700000000000 period:0
kworker/0:1-67 [000] 145.155593: rtc_timer_fired: RTC timer:(ffffffc15eb49bc8) expires:1510301700000000000 period:0
kworker/0:1-67 [000] 145.172504: rtc_set_alarm: UTC (1510301820) (0)
the second alarm timer was expired:
kworker/0:1-67 [000] 269.102353: rtc_timer_dequeue: RTC timer:(ffffff80088e6430) expires:1510301820000000000 period:0
kworker/0:1-67 [000] 269.102360: rtc_timer_fired: RTC timer:(ffffff80088e6430) expires:1510301820000000000 period:0
disable alarm irq:
kworker/0:1-67 [000] 269.102469: rtc_alarm_irq_enable: disable RTC alarm IRQ (0)
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Belloni