The Apple SMC uses a systematic labeling scheme for the hardware
temperature sensors. This scheme is currently hidden from
userland. Since the sensor set, and consequently the numbering,
differs between models, an extensive database of configurations is
required for an application such as fan control. This patch adds the
SMC labels to the hwmon sysfs interface, allowing applications to use
the sensors more intelligibly.
[rydberg@euromail.se: fixed error handling]
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds generic support for the MacBook Pro 7 family
based on the 7,1 model.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds generic support for the MacBook Pro 6 family
based on the 6,2 model.
[rydberg@euromail.se: patch cleanup]
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The MacBookPro 5,3 model has two fans, whereas the 5,4 model has
only one. This patch adds explicit support for the 5,3 and 5,4 models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Replace octal representation of file permissions by the corresponding
constants.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on earlier work by Ira W. Snyder.
The adm1031 chip is capable of using a runtime configurable sampling rate,
using the fan filter register. Add support for reading and setting the
update rate via sysfs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
The lm90 driver programs the sensor chip to update its readings at 2 Hz
(500 ms between readings). However, the driver only does reads from the
chip at intervals of 2 * HZ (2000 ms between readings). Change the driver
update rate to the programmed update rate.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acquire the I/O region for the Super I/O chip while we're working on it.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some code cleanup: properly use previously defined functions, rather
than duplicating their code.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use the strict_strol and strict_stroul functions instead of simple_strol
and simple_stroul respectively in sysfs functions.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fixed several coding style issues.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM64 appears to be an LM63 with added GPIO lines. Add support for the
hwmon functionality - GPIO can be added at some later stage if someone
has a need for them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When the user passes the kernel parameter acpi_enforce_resources=lax,
the ACPI resources are no longer protected, so a native driver can
make use of them. In that case, we do not want the asus_atk0110 to be
loaded. Unfortunately, this driver loads automatically due to its
MODULE_DEVICE_TABLE, so the user ends up with two drivers loaded for
the same device - this is bad.
So I suggest that we prevent the asus_atk0110 driver from loading if
acpi_enforce_resources=lax.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Len Brown <lenb@kernel.org>
The MSR IA32_TEMPERATURE_TARGET contains the TjMax value in the newer
Intel processors.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The thermal sensors of Intel(R) CPUs can be detected by CPUID instruction,
indicated by CPUID.06H.EAX[0].
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Content for the 8bit device threaded interrupt handlers. Depending on the
interrupt line and chip configuration, either click or wakeup / freefall
handler is called. In case of click, BTN_ event is sent via input device.
In case of wakeup or freefall, input device ABS_ events are updated
immediatelly.
It is still possible to configure interrupt line 1 for fast freefall
detection and use the second line either for click or threshold based
interrupts. Or both lines can be used for click / threshold interrupts.
Polled input device can be set to stopped state and still get coordinate
updates via input device using interrupt based method. Polled mode and
interrupt mode can also be used parallel.
BTN_ events are remapped based on existing axis remapping information.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original lis3 driver didn't provide interrupt handler(s) for click or
threshold event handling. This patch adds threaded handlers for one or
two interrupt lines for 8 bit device. Actual content for interrupt
handling is provided in the separate patch.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 bit device has two wakeup / free fall units. It was not possible to
configure the second unit. This patch introduces configuration entry to
the platform data and also corresponding changes to the 8 bit setup
function.
High pass filters were enabled by default. Patch introduces configuration
option for high pass filter cut off frequency and also possibility to
disable or enable the filter via platform data. Since the control is a
new one and default state was filter enabled, new option is used to
disable the filter. This way old platform data is still compatible with
the change.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Separate configuration function for 8 bit version of the chip. This way
generic part of the init function stays little bit more readable.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Definitions for click were missing.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'bkl/ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing:
uml: Pushdown the bkl from harddog_kern ioctl
sunrpc: Pushdown the bkl from sunrpc cache ioctl
sunrpc: Pushdown the bkl from ioctl
autofs4: Pushdown the bkl from ioctl
uml: Convert to unlocked_ioctls to remove implicit BKL
ncpfs: BKL ioctl pushdown
coda: Clean-up whitespace problems in pioctl.c
coda: BKL ioctl pushdown
drivers: Push down BKL into various drivers
isdn: Push down BKL into ioctl functions
scsi: Push down BKL into ioctl functions
dvb: Push down BKL into ioctl functions
smbfs: Push down BKL into ioctl function
coda/psdev: Remove BKL from ioctl function
um/mmapper: Remove BKL usage
sn_hwperf: Kill BKL usage
hfsplus: Push down BKL into ioctl function
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
These are the last remaining device drivers using
the ->ioctl file operation in the drivers directory
(except from v4l drivers).
[fweisbec: drop i8k pushdown as it has been done from
procfs pushdown branch already]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
The work queue has to be flushed after the device has been made
inaccessible. The patch closes a window during which a work queue might
remain active after the device is removed and would then lead to ACPI
calls with undefined behavior.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Herrmann <morpheus.ibis@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code will not remove the sysfs files for fan numbers three
and up. Also, upon exit, fans one and two are removed regardless of
their existence. This patch cleans up the sysfs error handling for
the fans.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* Allow fan minimum RPM to be set to zero without triggering alarms.
* Fix voltage scaling arithmetic and correct scale factors.
* Correct fan1-fan4 alarm bit shifts.
* Correct register address for temp3_smoothing_enable.
* Read the alarm registers with high priority.
Signed-off-by: Ken Milmore <ken.milmore@googlemail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Correct axis-mappings for new HP ProBook laptops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Annotate dynamic sysfs attribute in atk_create_files(). This gets
rid of the following lockdep warning:
BUG: key ffff8800379ca670 not in .data!
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2696 lockdep_init_map+0xd2/0x108()
Hardware name: P5K PRO
Modules linked in: asus_atk0110(+) pata_acpi firewire_ohci ata_generic
dm_multipath firewire_core crc_itu_t pata_marvell floppy
Pid: 599, comm: modprobe Not tainted 2.6.34-rc4 #27
Call Trace:
[<ffffffff8104cdb0>] warn_slowpath_common+0x7c/0x94
[<ffffffff8104cddc>] warn_slowpath_null+0x14/0x16
[<ffffffff81077c4d>] lockdep_init_map+0xd2/0x108
[<ffffffff81165873>] sysfs_add_file_mode+0x66/0xa2
[<ffffffff811658c0>] sysfs_add_file+0x11/0x13
[<ffffffff8116594b>] sysfs_create_file+0x2a/0x2c
[<ffffffff812c1f9c>] device_create_file+0x19/0x1b
[<ffffffffa005b4fd>] atk_add+0x58b/0x72e [asus_atk0110]
[<ffffffff812572a1>] acpi_device_probe+0x50/0x122
[<ffffffff812c46af>] driver_probe_device+0xa2/0x127
[<ffffffff812c4783>] __driver_attach+0x4f/0x6b
[<ffffffff812c4734>] ? __driver_attach+0x0/0x6b
[<ffffffff812c3c94>] bus_for_each_dev+0x59/0x8e
[<ffffffff812c4519>] driver_attach+0x1e/0x20
[<ffffffff812c4152>] bus_add_driver+0xb9/0x207
[<ffffffff812c4a5f>] driver_register+0x9d/0x10e
[<ffffffffa005f000>] ? atk0110_init+0x0/0x31 [asus_atk0110]
[<ffffffff81257c7c>] acpi_bus_register_driver+0x43/0x45
[<ffffffffa005f015>] atk0110_init+0x15/0x31 [asus_atk0110]
[<ffffffffa005f000>] ? atk0110_init+0x0/0x31 [asus_atk0110]
[<ffffffff81002069>] do_one_initcall+0x5e/0x15e
[<ffffffff81085075>] sys_init_module+0xd8/0x239
[<ffffffff81009cf2>] system_call_fastpath+0x16/0x1b
---[ end trace 4d0c84007055efb9 ]---
BUG: key ffff8800379ca638 not in .data!
BUG: key ffff8800379ca6a8 not in .data!
BUG: key ffff8800379ca6e0 not in .data!
BUG: key ffff880036f73670 not in .data!
BUG: key ffff880036f73638 not in .data!
BUG: key ffff880036f736a8 not in .data!
BUG: key ffff880036f736e0 not in .data!
BUG: key ffff880036f76c70 not in .data!
BUG: key ffff880036f76c38 not in .data!
BUG: key ffff880036f76ca8 not in .data!
BUG: key ffff880036f76ce0 not in .data!
BUG: key ffff8800368e7670 not in .data!
BUG: key ffff8800368e7638 not in .data!
BUG: key ffff8800368e76a8 not in .data!
BUG: key ffff8800368e76e0 not in .data!
BUG: key ffff880036ef7670 not in .data!
BUG: key ffff880036ef7638 not in .data!
BUG: key ffff880036ef76a8 not in .data!
BUG: key ffff880036ef76e0 not in .data!
BUG: key ffff8800373ccc70 not in .data!
BUG: key ffff8800373ccc38 not in .data!
BUG: key ffff8800373ccca8 not in .data!
BUG: key ffff8800373ccce0 not in .data!
BUG: key ffff880037a60870 not in .data!
BUG: key ffff880037a60838 not in .data!
BUG: key ffff880037a608a8 not in .data!
BUG: key ffff880037a608e0 not in .data!
BUG: key ffff880037355070 not in .data!
BUG: key ffff880037355038 not in .data!
BUG: key ffff8800373550a8 not in .data!
BUG: key ffff8800373550e0 not in .data!
BUG: key ffff8800378c2670 not in .data!
BUG: key ffff8800378c2638 not in .data!
BUG: key ffff8800378c26a8 not in .data!
BUG: key ffff8800378c26e0 not in .data!
BUG: key ffff880036ef7e70 not in .data!
BUG: key ffff880036ef7e38 not in .data!
BUG: key ffff880036ef7ea8 not in .data!
BUG: key ffff880036ef7ee0 not in .data!
Cc: Eric W. Biederman <ebiederm@xmission.com>
Reported-by: Dhaval Giani <dhaval.giani@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Dhaval Giani <dhaval.giani@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the iMac9,1 and the MacBookPro2,2 temperature sensors to hwmon
driver applesmc to fix kernel bug #14429:
https://bugzilla.kernel.org/show_bug.cgi?id=14429
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When any temperature sensor type is changed, the corresponding
temperature value needs to be updated. The register caching mechanism
may delay this update, so we want to invalidate the cache to force an
immediate update.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently, if someone tries to set the thermal sensor type to an
unsupported value, subsequent accesses to the chip may temporarily
show the sensor in question as disabled. Use a temporary variable
and only update the cached value on success, to prevent such
confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Temperature channels can be used in 2 different modes (thermistor and
thermal diode) and we don't know which one, if any, is correct for
every given board. So don't arbitrarily choose one. Instead, leave the
temperature channels untouched. They can be configured from user-space
if needed anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When CONFIG_REGULATOR isn't set, regulator_get_voltage() returns 0.
Properly handle this case by not trusting the value.
Reported-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
I discovered two issues.
First the previous sht15_calc_temp() loop did not iterate through the
temppoints array since the (data->supply_uV > temppoints[i - 1].vdd)
test is always true in this direction.
Also the two-points linear interpolation function was returning biased
values due to a stray division by 1000 which shouldn't be there.
[JD: Also change the default value for d1 from 0 to something saner.]
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Intel X58 have asc7621a chip. So added X58 entry in Kconfig for asc7621.
Also arranged existing models in ascending order.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
"ret" is used to store the return value for watchdog_trigger() and it
should be signed for the error handling to work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add missing newline to dev_warn() message string. This is more of an issue
with older kernels that don't automatically add a newline if it was missing
from the end of the previous line.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Avoid hex and decimal confusion when printing out the cpu model.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (23 commits)
hwmon: Remove the deprecated adt7473 driver
hwmon: Fix off-by-one kind values
hwmon: (tmp421) Fix temperature conversions
hwmon: (tmp421) Restore missing inputs
hwmon: Driver for Andigilog aSC7621 family monitoring chips
hwmon: (adt7411) Improve locking
hwmon: Add driver for ADT7411 voltage and temperature sensor
hwmon: (w83793) Add watchdog functionality
hwmon: (g760a) Make rpm_from_cnt static
hwmon: (it87) Validate auto pwm settings
hwmon: (it87) Add support for old automatic fan speed control
hwmon: (it87) Drop dead web links in documentation
hwmon: (it87) Add an entry in MAINTAINERS
hwmon: (it87) Use strict_strtol instead of simple_strtol
hwmon: (it87) Fix many checkpatch errors and warnings
hwmon: (it87) Add support for beep on alarm
hwmon: (it87) Create vid attributes by group
hwmon: (it87) Refactor attributes creation and removal
hwmon: (it87) Expose the PWM/temperature mappings
hwmon: (it87) Display fan outputs in automatic mode as such
...
While testing an ADC121S021 in an embedded board with a S3C2142 SoC (ARM
core), I have found that the 'adcxx' driver does not handle correctly
single channel ADCs from this chip family. For single channel chips you
must only issue one read transfer for correct measurement.
Signed-off-by: Jose Miguel Goncalves <jose.goncalves@inov.pt>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
String constants that are continued on subsequent lines with \ will cause
spurious whitespace in the resulting output.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
adt7473 driver is obsoleted by adt7475 driver. And it is scheduled
to be removed in Feb 2010.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Recent changes on the I2C front have left off-by-one array indexes in
3 hwmon drivers. Fix them.
Faulty commit:
e5e9f44c2 i2c: Drop I2C_CLIENT_INSMOD_2 to 8
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
The low bits of temperature registers are status bits, they must be
masked out before converting the register values to temperatures.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
An off-by-one error caused some inputs to not be created by the driver
when they should. TMP421 gets only one input instead of two, TMP422
gets two instead of three, etc. Fix the bug by listing explicitly the
number of inputs each device has.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
Hwmon driver for Andigilog aSC7621 family monitoring chips.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add proper locking for the cached variables. Also get rid of
ref_is_vdd, which became obsolete.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add basic support for the ADT7411. Reads out all conversion results (via I2C,
SPI yet missing) and allows some on-the-fly configuration. Tested with a
custom board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add watchdog functionality to the Winbond W83793 driver.
Signed-off-by: Sven Anders <anders@anduras.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Function rpm_from_cnt is only used internally so it can be made
static. Make it inline while we're here, for performance reasons
(although hopefully gcc would figure out by itself...)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Before switching to automatic fan control mode, make sure that all the
trip points make sense. Otherwise, the control loop could lead to
weird fan behavior.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the automatic fan speed control interface as
implemented by IT8705F chips up to revision F and IT8712F chips up to
revision G. This implementation fits very well in our standard sysfs
interface.
I implemented the old and not the new interface because the only chip
I have at hand is an old one, and the new interface is more difficult
to map to the standard sysfs interface. Adding support later should be
possible though, if someone with a supported chip is interested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix 20 errors and 11 warnings reported by the checkpatch script. The
remainining errors would require more work. The remaining warnings
will be addressed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The IT87xxF chips support beeping on alarm, if properly wired and
configured. There is one control bit for each input type (temperature,
fan, voltage.) Let the user see and change them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only VID-related attributes are left in it87_attributes_opt, so we
might as well rename it to it87_attributes_vid and use this group to
create all attributes at once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a lot of code redundancy in the creation of the fan and
pwm attributes. Move these attributes to arrays so that the code can
be simplified.
This in turns makes the attributes removal code larger, so move it to
a separate function that can be called in both the standard removal
case and the error path during probing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the user read the PWM-to-temperature mappings. Until the trip
points are also exposed, this is essentially a way to know how the
BIOS has set things up. The ability to change the settings will be
added later, together with the trip points.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't yet support automatic fan control. Let it at
least tell the user when a fan output is in automatic mode. Also let
the user switch from automatic mode (possibly set by the BIOS) to
manual mode and back without losing the settings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested successfully with an ADM1032 chip on its evaluation board. It
should work fine with all other chips as well.
At this point this is more of a proof-of-concept, we don't do anything
terribly useful on SMBus alert: we simply log the event. But this could
later evolve into libsensors signaling so that user-space applications
can take an appropriate action.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
Restore the chip configuration when unloading the driver. This ensures
we don't leave the chip running if it was initially stopped.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This chips is found on several Zotac Ion ITX boards, amongst others.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: MC Matti <mcmatti17@googlemail.com>
Cc: Manuel Lamotte-Schubert <mls@pronego.com>
Different motherboards have different PNP declarations for
W83781D/W83782D chips. Some declare the whole range of I/O ports (8
ports), some declare only the useful ports (2 ports at offset 5) and
some declare fancy ranges, for example 4 ports at offset 4. To
properly handle all cases, request all ports individually for probing.
After we have determined that we really have a W83781D or W83782D
chip, the useful port range will be requested again, as a single
block.
I did not see a board which needs this yet, but I know of one for lm78
driver and I'd like to keep the logic of these two drivers in sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Different motherboards have different PNP declarations for LM78/LM79
chips. Some declare the whole range of I/O ports (8 ports), some
declare only the useful ports (2 ports at offset 5) and some declare
fancy ranges, for example 4 ports at offset 4. To properly handle all
cases, request all ports individually for probing. After we have
determined that we really have an LM78 or LM79 chip, the useful port
range will be requested again, as a single block.
This fixes the driver on the Olivetti M3000 DT 540, at least.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
The #define ADT7462_VOLT_COUNT is wrong, it should be 13 not 12. All the
for loops that use this as a limit count are of the typical form, "for
(n = 0; n < ADT7462_VOLT_COUNT; n++)", so to loop through all voltages
w/o missing the last one it is necessary for the count to be one greater
than it is. (Specifically, you will miss the +1.5V 3GPIO input with count
= 12 vs. 13.)
Signed-off-by: Ray Copeland <ray.copeland@aprius.com>
Acked-by: "Darrick J. Wong" <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Some code that is in ams_exit() (the module exit code) should instead
be called when the device (not module) is removed. It probably doesn't
make much of a difference in the PMU case, but in the I2C case it does
matter.
I make no guarantee that my fix isn't racy, I'm not familiar enough
with the ams driver code to tell for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When /dev/watchdog gets opened a second time we return -EBUSY, but
we already have got a kref then, so we end up leaking our data struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
MBIF (motherboard identification) is only used to print the name of
the board, it's not essential for the driver; do not fail if it's
missing. Based on Juan's patch.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Juan RP <xtraeme@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
smsc47m1_restore is called from sm_smsc47m1_exit, which is an __exit
function, so it can't be __init.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make pci_device_id also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The max junction temperature of Atom N450/D410/D510 CPUs is 100 degrees
Celsius. Since these CPUs are always coupled with Intel NM10 chipset in
one package, the best way to verify whether an Atom CPU is N450/D410/D510
is to check the host bridge device.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The latest version of the Revision Guide for AMD Family 10h Processors
lists two more processor revisions which may be affected by erratum 319.
Change the blacklisting code to correctly detect those processors, by
implementing AMD's recommended algorithm.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Expose the raw GGRP/GITM interface via debugfs. The hwmon interface is
reverse engineered and the driver tends to break on newer boards...
Using this interface it's possible to poke directly at the ACPI methods
without the need to recompile, reducing the guesswork and the round trips
needed to support a new revision of the interface.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The behaviour is unmodified, this makes easier to override the heuristic (which
is probably needed for some boards).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The ADT7462_PIN28_VOLT value is a 4-bit field, so the corresponding
shift must be 4.
Signed-off-by: Roger Blofeld <blofeldus@yahoo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83627hf) Fix for "No such device"
hwmon: (sht15) Off-by-one error in array index + incorrect constants
hwmon: Add driver for VIA CPU core temperature
hwmon: (smsc47m1) Enable device if needed
hwmon: (smsc47m1) Fail module loading on error
hwmon: (smsc47m1) Only request I/O ports we really use
hwmon: New driver for AMD Family 10h/11h CPUs
The commit b72656dbc4 introduced
a bug leading to the w83627hf_find function no longer finding
any chips.
Signed-off-by: Christian Schulte <cs@schulte.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix an off-by-one error in array index + incorrect constants.
Signed-off-by: Christoph Walser <walser@tik.ee.ethz.ch>
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a driver for the on-die digital temperature sensor of
VIA's recent CPU models.
[JD: Misc clean-ups.]
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Adam Nielsen <a.nielsen@shikadi.net>
If the address is set but the device isn't enabled, attempt to enable
it. If it won't work for any reason (resource conflict, no function
enabled) the initial state is restored. The initial state is also
restored on module unloading.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sean Fidler <fidlersean@gmail.com>
If an error occurs during probing, there's no point in keeping the
module in memory. Better fail the module loading early to make the
problem more visible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sean Fidler <fidlersean@gmail.com>
The I/O area of the SMSC LPC47M1xx chips which we use, gives access to
a lot of registers, some of which are related to fan speed monitoring
and control, but many are not. At the moment, the smsc47m1 driver
requests the whole I/O port range. This could easily result in
resource conflicts with either ACPI or other drivers.
Request only the I/O ports we really use, to prevent such conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sean Fidler <fidlersean@gmail.com>
This adds a driver for the internal temperature sensor of AMD Family 10h
and 11h CPUs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Report output values as 1/1000 of earth gravity.
Output values from lis3 can be read from sysfs position entry and from
input device. Input device can be accessed as event device and as
joystick device. Joystick device can be in two modes. Meaning of the
output values varies from case to case depending on the chip type and
configuration (scale). Only joystick interface in JS_CORR_BROKEN mode
returned somehow similar output values in different configurations.
Joystick device is in that state by default in case of lis3.
Position sysfs entry, input event device and raw joystick device have been
little bit broken since meaning of the output values has been varied
between 12 and 8 bit devices. Applications which relayed on those methods
failed if the chip is different than the expected one.
This patch converts output values to mean similar thing in different
configurations. Both 8 and 12 bit devices reports now same acceleration
values. If somebody implements full scale support to the driver, output
values will still mean the same. Scaling factor and input device range
must be updated in that case.
Joystick interface in JS_CORR_BROKEN mode is not touched by this patch.
All other interfaces have different scale after this change. For 12 bit
device scaling factor is 0.977 which keeps scaled and unscaled values are
quite close to each others. For 8 bit device, scaled values are 18 times
bigger than unscaled values.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible to read position information at the chip measurement rate
via sysfs. This patch adds possibility to configure chip measurement
rate.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chip is calibrated by the manufacturer. There is no need to calibarate it
at driver level. If the chip is used as a joystick, calibaration can be
done using joystick device calibration mechanism.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement selftest feature as specified by chip manufacturer. Control:
read selftest sysfs entry
Response: "OK x y z" or "FAIL x y z"
where x, y, and z are difference between selftest mode and normal mode.
Test is passed when values are within acceptance limit values.
Acceptance limits are provided via platform data. See chip spesifications
for acceptance limits. If limits are not properly set, OK / FAIL decision
is meaningless. However, userspace application can still make decision
based on the numeric x, y, z values.
Selftest is meant for HW diagnostic purposes. It is not meant to be
called during normal use of the chip. It may cause false interrupt
events. Selftest mode delays polling of the normal results but it doesn't
cause wrong values. Chip must be in static state during selftest. Any
acceration during the test causes most probably failure.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lis3 accelerometer sensors have quite long power on delay (up to 125
ms). This patch adds necessary delay to power on sequence for currently
supported lis3 chips.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Originally the driver was only targeted to 12bits sensors. When support
for 8bits sensors was added, some slight difference in the registers were
overlooked. This should fix it, both for initialization, and for
displaying the rate.
Reported-by: Kalhan Trisal <kalhan.trisal@intel.com>
Reported-by: Christoph Plattner <christoph.plattner@gmx.at>
Tested-by: Christoph Plattner <christoph.plattner@gmx.at>
Tested-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Send input_sync after each measurement round. This helps userspace to
detect which reported values belongs to the same measurement.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level. Add control of rate of change of fan output
level. These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority. Add
support for constant fan speed and proportional-response operations modes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These macros simply declare an enum, so drivers might as well declare
it themselves. This puts an end to the arbitrary limit of 8 chip types
per i2c driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
This macro simply declares an enum, so drivers might as well declare
it themselves.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Struct i2c_client_address_data only contains one field at this point,
which makes its usefulness questionable. Get rid of it and pass simple
address lists around instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
The "kind" parameter always has value -1, and nobody is using it any
longer, so we can remove it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (41 commits)
hwmon: (adt7475) Add VID support for the ADT7476
hwmon: (adt7475) Add an entry in MAINTAINERS
hwmon: (adt7475) Add support for the ADT7476
hwmon: (adt7475) Voltage attenuators can be bypassed
hwmon: (adt7475) Print device information on probe
hwmon: (adt7475) Handle alternative pin functions
hwmon: (adt7475) Move sysfs files removal to a separate function
hwmon: (adt7475) Add support for the ADT7490
hwmon: (adt7475) Improve device detection
hwmon: (adt7475) Add missing static marker
hwmon: (adt7475) Rework voltage inputs handling
hwmon: (adt7475) Implement pwm_use_point2_pwm_at_crit
hwmon: (adt7475) New documentation
hwmon: (adt7475) Add support for the ADT7473
hwmon: (f71882fg) Add support for the f71889fg (version 2)
hwmon: (f71882fg) Fix sysfs file removal
hwmon: (f71882fg) Cleanup sysfs attr creation 2/2
hwmon: (f71882fg) Cleanup sysfs attr creation 1/2
hwmon: (thmc50) Stop using I2C_CLIENT_MODULE_PARM
hwmon: Add Freescale MC13783 ADC driver
...
The ADT7476 has 5 dedicated pins for VID input, and the +12V input can
optionally be used as a 6th VID pin. Add support for VID input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7476 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 5 voltage inputs instead of 2, and VID input
pins.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
It is possible to bypass the voltage attenuators on the +2.5V, Vccp,
+5V and +12V voltage monitoring inputs. This is useful to connect
other voltage channels than the ones the monitoring chip was
originally designed for. When this feature is enabled, we must not
include the scaling factors in our computations.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Print the device name and revision at probe time, as well as a list of
all optional features which are available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
The TACH4 pin can be used for other functions, so fan4 may not always
be available. Likewise, the PWM2 pin can be used for ALERT output, in
which case pwm2 is not available
For the ADT7490, the +2.5 Vin pin may also be used for other
functions, in which case in0 is not available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Move sysfs files removal to a separate function. The code is common to
the device probing error path and the standard device removal path. As
it will grow with future driver development, this avoids code
duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7490 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 6 voltage inputs instead of 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Check the value of register 0x3f as part of the device detection, to
make it more robust.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
adt7475_attr_group is used internally only and can thus be marked
static.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Rework the handling of voltage inputs to make it possible and easy to
support more inputs. This will be needed for the upcoming ADT7490
support.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Implement the non-standard pwm_use_point2_pwm_at_crit sysfs attribute
as the adt7473 driver did.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the ADT7473 to the adt7475 driver, and mark the
adt7473 driver for removal. The ADT7473 and ADT7475 chips are almost
the same chip and essentially compatible, so there's no point in
having separate drivers for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
This adds support for the Fintek f71889fg to the f71882fg driver,
many thanks to Gerd v. Egidy for providing (remote) access to a
machine which such an ic.
Note that this bit of the patch:
- val = SENSORS_LIMIT(val, 0, 255);
+
+ if (data->type == f71889fg)
+ val = SENSORS_LIMIT(val, -128, 127);
+ else
+ val = SENSORS_LIMIT(val, 0, 127);
Changes behaviour for already supported models, the new behaviour is correct
as the already supported models have bit 7 of the involved registers fixed at
0, so the previous behaviour which allowed setting temp zone limits > 127
was not correct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a bug in the old sysfs file removal, as it uses fxxxx_in_temp_attr
to remove the in and temp sysfs attributes, but fxxxx_in_temp_attr has
temp#_alarm, where as f71858fg_in_temp_attr has temp#_max_alarm, so
the temp#_max_alarm attributes for the f71858fg never get removed.
This patch fixes this by doing the sysfs removal exactly the same way as
the creation instead of being (too) clever, this will also avoid similar
bugs in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch merges the f71882fg_auto_pwm_attr array into the
fxxxx_fan_attr resp. fxxxx_auto_pwm_attr array, as the f71882fg_auto_pwm_attr
array was merely extending these 2 with entries for a 4th fan, it also makes
these 2 arrays 2 dimensional so that the rest of the code can choose to
add attr for 3 or 4 fans without needing to know the nr of attr per fan.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch makes a number of cleanups to the sysfs attr creation
in the f71882fg driver, this is a preparation patch for adding f71889fg
support:
* Add some comments to explain why some models need separate sysfs attr
arrays for in / temp / fan / pwm
* Rename a number of sysfs attr arrays to make their function clearer
* Move the pwm#_auto_channels_temp attribute from the common to all
models fan attr array to the per model auto mode pwm attr arrays, so
that all the auto mode pwm attr are grouped together, and thus can be
left out on models where we don't support auto pwm mode
* Put fan_beep attr in their own array, so that only auto mode pwm attr
remain in the per model pwm sysfs attr arrays.
* Put the 4th special fan input for the f8000 in its own array, so that only
auto mode pwm attr remain in the per model pwm sysfs attr arrays.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The thmc50 driver is the last user of I2C_CLIENT_MODULE_PARM, and I
would like to get rid of that macro.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Krzysztof Helt <krzysztof.h1@wp.pl>
This driver provides support for the ADC integrated into the
Freescale MC13783 PMIC.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The w83791d driver has been in the kernel for a while now,
time to remove the EXPERIMENTAL dependency.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As kind is now hard-coded to -1, there is room for code clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Riku Voipio <riku.voipio@iki.fi>
Acked-by: "Hans J. Koch" <hjk@linutronix.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
As kind is now hard-coded to -1, there is room for code clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Marc Hulsman <m.hulsman@tudelft.nl>
As kind is now hard-coded to -1, there is room for code clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Andre Prendel <andre.prendel@gmx.de>
The National Semiconductor LM73 is a single temperature sensor, much
like the famous LM75.
Signed-off-by: Adrien Demarez <adrien.demarez@bolloretelecom.eu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Stop using global variables REG and VAL for I/O port numbers. This is
ugly and unsafe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
This module parameter is there to workaround broken BIOS. I'm not even
sure if it was used in the past 5 years, and it gets in the way of
converting the driver to the MFD infrastructure. So tell the users how
they can do the same from user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
The fan2 and fan3 input and output pins can be used as GPIOs. Check
their function before exposing their sysfs attributes and accessing
their registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The VID input pins can alternatively be used as GPIOs. Make sure we
have at least 4 pins used for VID, otherwise don't bother reading and
exposing VID.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Adam Nielsen <a.nielsen@shikadi.net>
The previous patch, commit be4c23c93c was
from the wrong tree and thus broke the current build which had the
channel configuration name changed.
Fix the following build errors:
drivers/hwmon/s3c-hwmon.c: In function 's3c_hwmon_probe':
drivers/hwmon/s3c-hwmon.c:326: warning: initialization from incompatible pointer type
drivers/hwmon/s3c-hwmon.c:331: error: dereferencing pointer to incomplete type
drivers/hwmon/s3c-hwmon.c:336: error: dereferencing pointer to incomplete type
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The adt7475 driver creates pwm#_auto_channel_temp attributes instead
of the standard pwm#_auto_channels_temp. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
The comment says that limits are cached for 60 seconds but the code
actually caches them for only 2 seconds. Align the code on the
comment, as 60 seconds makes more sense.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
The logic of temperature fault flags is wrong, it shows faults when
there are none and vice versa. Fix it.
I can't believe this has been broken since the driver was added, 8
months ago, basically breaking temp1 and temp3, and nobody ever
complained.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Avoid registering channels that have zero divider settings in them, as this
will only lead to kernel OOPS from divide-by-zero when the sysfs entry is
read.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (it87) Fix VID reading on IT8718F/IT8720F
hwmon: (dme1737) No vid attributes for SCH311x
hwmon: (fschmd) Fix check on unsigned in watchdog_write()
hwmon: (coretemp) Maintainer update
I have an HP HDX 18 laptop, and noted that the configuration of the
accelerometer needs to be x_inverted.
Signed-off-by: Ian E. Morgan <penguin.wrangler@gmail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have learned that the 6730b and 6730s have different accelerometer
orientation, and have modified the driver accordingly (diff attached),
while dropping the wild guess for AMD based 6735 having the same
orientation as Intel based 6730 (this is not true for any other related
series/family, thus is not probable for 673x).
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Comparing apples to bananas doesn't seem right. Consistently use the
chips enum for chip type comparisons, to avoid such bugs in the
future.
The bug has been there since support for the IT8718F was added, so
VID never worked for this chip nor for the similar IT8720F.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SCH311x chips do not have VID inputs, so the cpu0_vid and vrm
attributes shouldn't be created for them.
This fixes lm-sensors ticket #2353:
http://www.lm-sensors.org/ticket/2353
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Udo van den Heuvel <udovdh@xs4all.nl>
Cc: Juerg Haefliger <juergh@gmail.com>
If unsigned the watchdog_trigger() return value will not be
checked correctly.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
The s3c-hwmon driver depends on the arch/arm implementation of the core
ADC support for the chip. Since the S3C64xx version has not yet been
merged disable building of the driver on S3C64xx for now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On newer ASUS boards (e.g. P7P55D) the EC (that - among other things - is
responsible for updating the readings from the hwmon sensors) is disabled
by default since ASUS detected conflict with some tools under Windows.
The following patch checks the state of the EC and enable it if needed;
under Linux, native drivers are locked out from ACPI owned resources so
there's no risk of conflict.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Robert Hancock <hancockrwd@gmail.com>
Tested-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Refactor the code of the new style interface around GGRP (enumeration) and
GITM (read) helpers to mimic ASL code. Also switch the read path to use
dynamic buffers (handled by ACPI core) since ASUS expanded the return buffer
(ASBF) in newer boards (e.g. P7P55D).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Robert Hancock <hancockrwd@gmail.com>
Tested-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix spurious section mismatch warnings, caused due to reference from
variable sht_drivers to
__devinit/__devexit functions sht15_probe()/remove().
We were warned by the following warnings:
LD drivers/hwmon/built-in.o
WARNING: drivers/hwmon/built-in.o(.data+0x264a0): Section mismatch in
reference from the variable sht_drivers to the function
.devinit.text:sht15_probe()
The variable sht_drivers references
the function __devinit sht15_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: drivers/hwmon/built-in.o(.data+0x264a4): Section mismatch in
reference from the variable sht_drivers to the function
.devexit.text:sht15_remove()
The variable sht_drivers references
the function __devexit sht15_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: drivers/hwmon/built-in.o(.data+0x264f0): Section mismatch in
reference from the variable sht_drivers to the function
.devinit.text:sht15_probe()
The variable sht_drivers references
the function __devinit sht15_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: drivers/hwmon/built-in.o(.data+0x264f4): Section mismatch in
reference from the variable sht_drivers to the function
.devexit.text:sht15_remove()
The variable sht_drivers references
the function __devexit sht15_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: drivers/hwmon/built-in.o(.data+0x26540): Section mismatch in
reference from the variable sht_drivers to the function
.devinit.text:sht15_probe()
The variable sht_drivers references
the function __devinit sht15_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: drivers/hwmon/built-in.o(.data+0x26544): Section mismatch in
reference from the variable sht_drivers to the function
.devexit.text:sht15_remove()
The variable sht_drivers references
the function __devexit sht15_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: drivers/hwmon/built-in.o(.data+0x26590): Section mismatch in
reference from the variable sht_drivers to the function
.devinit.text:sht15_probe()
The variable sht_drivers references
the function __devinit sht15_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is no point in implementing a detect callback for the LTC4215
and LTC4245, as these devices can't be detected. It was there solely
to handle "force" module parameters to instantiate devices, but now
we have a better sysfs interface that can do the same.
So we can get rid of the ugly module parameters and the detect
callbacks. This shrinks the binary module sizes by 36% and 46%,
respectively.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (ltc4245) Clear faults at startup
hwmon: (ltc4215) Clear faults at startup
hwmon: (coretemp) Add Lynnfield CPU
hwmon: (coretemp) Add support for Penryn mobile CPUs
hwmon: (coretemp) Fix Atom CPUs support
hwmon: Delete deprecated FSC drivers
hwmon: (adm1031) Add sysfs files for temperature offsets
When power is applied to the ltc4245 chip it sometimes reports spurious
faults, which are exposed as alarms in the hwmon output. Clear the fault
register when the driver is installed to clear the alarms.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When power is applied to the ltc4215 chip it sometimes reports spurious
faults. The faults are not yet exposed via sysfs, however it may be useful
for userspace to read the fault register directly with the i2cget command.
Clear the fault register when the driver is installed so userspace doesn't
have to worry about spurious fault indications.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add Lynnfield processor support. Lynnfield is a quad-core Nehalem
based microprocessor for Desktop market, which is introduced in
September 2009.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Kent Liu <kent.liu@linux.intel.com>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Following patch adds support for mobile Penryn CPUs. Intel documents this
poorly. I asked the Coretemp author for some help. This is totally untested and
may not work. Please test!
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix Atom CPUs support. Intel documents TjMax at 90 degrees C but
some Atoms may have 125 degrees C (this is undocumented speculation).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy fscpos and fscher drivers have been replaced by the unified
fschmd driver. The transition period is over now, we can delete them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The ADM1030/ADM1031 chips have temperature offset registers, for both the
local and remote temperature sensors. Following the example set forth in
the LM90/ADM1032 driver, expose the offset registers to userspace.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the code a little bit nicer, and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the code a little bit nicer, and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The static code scanner "Parfait" reported this because pwm_config is
only 3 bytes - pwm_config[3] is out of range.
Since this code path is never called with ix == 3 (the device has no PWM4
output) this doesn't change anything in practice. But to encourage
testing with Parfait, lets make the warning go away...
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On resume from suspend, the driver currently resets the logical state as
if it was brought up from halt. This patch uses the
dev_pm_ops.resume/restore methods to synchronize the hardware with the
memorized logical state, in effect bringing back the accelerometer and
backlight to the state prior to suspend. Works for both suspend to ram
and hibernation. The patch has zero effect on the running state.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If already requested, gpio_data and irq should be freed in the case of an
error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Occasionally it is helpful to be able to turn a temperature sensor off
(for example if it's making unwanted electrical noise). This patch
adds a sysfs node to put any adm1021 compatible device into low power mode.
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ADM1023 temperature sensor supports higher resolution for its external
sensor (sensitivity of 1/8 deg C). This patch makes this higher
resolution available through the appropriate temperature sysfs nodes.
Curiously, this functionality was available in the 2.4 kernel driver (but
formatted in a less helpful manner).
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This enabled power management functions for the SPI transport layer of the
lis3 devices. The device's suspend mode is only entered in case no wakeup
threshold has been given. In this case, the device is supposed to wake up
the system and must thus not be put to deep sleep.
[randy.dunlap@oracle.com: fix lis3-spi for CONFIG_PM=n]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This offers a way for platforms to define flags and thresholds for the
free-fall/wakeup functions of the lis302d chips.
More registers needed to be seperated as they are specific to the
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable the coretemp driver on an Intel Atom.
I'm not sure if the readings are correct, however - on my 330, the driver
reports values between 27 and 41 °C (with core1 being about 8°C hotter
than core0, given the same load). Maybe the maximum temperature of 100 °C
is wrong for Atom CPUs.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver adds support for the hardware monitoring features of
the WM831x PMICs to the hwmon API. Monitoring is provided for
the system voltages supported natively by the WM831x, the chip
temperature, the battery temperature and the auxiliary inputs
of the WM831x.
Currently no alarms are supported, though digital comparators on
the WM831x devices would allow these to be provided.
Since the auxiliary and battery temperature input scaling depends
on the system configuration the value is reported as a voltage to
userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Winbond/Nuvoton WPCD377I is the reduced version of a Super-I/O
which emulates the National Semiconductor LM96000 hardware monitoring
chips, but without the hardware monitoring part. Instead of plain
disabling the emulation, the vendor left the emulated chip visible,
but all monitored values are always zero. This is rather confusing for
the users. So detect this case and refuse to bind to such fake chips.
This fixes lm-sensors ticket #2182:
http://www.lm-sensors.org/ticket/2182
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that we have ACPI-based hardware monitoring drivers, and we will
start telling users to use them instead of native drivers when I/O
resources conflict, I think it would be good to clearly mark ACPI
drivers as such in Kconfig.
Also, in the case of monolithic kernels, I think the ACPI drivers
should take precedence over native drivers, so they should be listed
first in Makefile.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Luca Tettamanti <kronos.it@gmail.com>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Drivers should be including <linux/io.h> instead of <asm/io.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Frank Seidel <frank@f-seidel.de>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for Texas Instruments TMP421/422/423 temperature sensor IC.
TI's TMP421/422/423 are I2C temperature sensor chips. These chips are
similar to TI's TMP401/411 chips, but with reduced functionality (only
temperature measurement). The chips have one local sensor and up to
three (TMP423) remote sensors.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We had a report about a mainboard for AMD family 0Fh processors not
routing the 6th VID pin from the CPU to the hardware monitoring chip.
While the vendor should have wired the pin (or, failing that, should
have hardwired it to level high rather than low), the fact is that
none of these processors are currently known to operate at the lower
voltage levels which require the 6th VID pin. So, as a practical
workaround, I propose to ignore the 6th VID pin for these CPUs.
If this decision ever causes problems, we'll reconsider.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Frank Myhr <fmyhr@fhmtech.com>
Tested-by: Hleb Valoshka <375gnu@gmail.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Most known Abit motherboards have unique uguru chip IDs. However,
some "refresh" boards keep the same chip ID but have a different
DMI string. As our DMI board string matching is (necessarily)
strict, some boards were failing DMI detection, and as the old
probe method was also failing, the driver would not load.
The only known boards affected by this problem are the IP35 Pro XE
(vs IP35 Pro) and the AB9 Pro (vs AB9). Is it not sufficient to
relax the match criteria, as some boards (e.g. the AB9 Quad GT)
have different uguru chip IDs.
This patch replaces the dmi_name string with a NULL terminated
array of strings to be matched per uguru chip ID. It has been
compile and runtime tested (thanks Rune).
References: https://bugs.launchpad.net/bugs/298798
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Rune Svendsen <runesvend@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On newer Asus boards the "upper" limit of a sensor is encoded as
delta from the "lower" limit. Fix the driver to correctly handle
this case.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Alex Macfarlane Smith <nospam@archifishal.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SMSC LPC47M233 and LPC47M292 chips have the same device ID but
are not compatible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add support for the ADC controller on the S3C series of processors to
drivers/hwmon for use with hardware monitoring systems.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Switch the AB9, AB9 QuadQT and IX38 QuadGT over from port
probing to the preferred DMI probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: dan <dan@deeog.com>
Tested-by: Nygel Lyndley <nygel.lyndley@gmail.com>
Tested-by: Dmitriy Fedchenko <dmitriy-fedc@yandex.ru>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add omitted update_lock to one switch/case in set_div.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
The LIS302DL accelerometer chip has a 'click' feature which can be used to
detect sudden motion on any of the three axis. Configuration data is
passed via spi platform_data and no action is taken if that's not
specified, so it won't harm any existing platform.
To make the configuration effective, the IRQ lines need to be set up
appropriately. This patch also adds a way to do that from board support
code.
The DD_* definitions were factored out to an own enum because they are
specific to LIS3LV02D devices.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Separate the 6710 and 6715, and set the right axis information for the
6715.
Reported-by: Isaac702 <isaac702@gmail.com>
Add the 6930.
Reported-by: Christian Weidle <slateroni@gmail.com>
Add the 2710.
Reported-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that there is no need to hookup on the open/close of the joystick,
it's possible to use the simplified interface input_polled_device, instead
of creating our own kthread.
[randy.dunlap@oracle.com: fix Kconfig]
[randy.dunlap@oracle.com: fix Kconfig some more]
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After measurement on my laptop, it seems that turning off the device does
not bring any energy saving (within 0.1W precision). So let's keep the
device always on. It simplifies the code, and it avoids the problem of
reading a wrong value sometimes just after turning the device on.
Moreover, since commit ef2cfc790b had been
too zealous, the device was actually never turned off anyway. This patch
also restores the damages done by this commit concerning the
initialisation/poweroff.
Also do more clean up with the usage of the lis3_dev global variable.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Can only unregister the misc device if it was registered before. Also
remove debugging messages, which in addition were not properly formated.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the alarm flags provided by the MAX6650/MAX6651 fan-speed regulator
and monitor chips via sysfs.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the hwmon part of the Fintek F71858FG superio IC to the
f71882fg driver. Many thanks to Jelle de Jong for lending me a motherboard
with this superio on it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on f71852fg support I noticed that the f8000 sysfs attr
table was missing entries for temp#_fault, which the f8000 does have and
which we were already reading.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We depend up on the pwm_enable register (0x96) not containing any reserved
settings in various places. We were already checking to make sure there
were no reserved settings in the register for the f71862fg, this patch adds
the same checking for the f8000, while at it it also moves the code to
a more apropriate place so we don't need to check if the fan/pwm part
of the IC is enabled twice.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently we are using separate per model sysfs attr for the 3th pwm, because
the 3th pwm of the f8000 only has automatic mode and not manual mode. Doing
things this way was getting in the way for adding f71858fg support, so this
patch makes the pwm attr identical for all models, and instead adds a check
to store_pwm_enable() disallowing setting the 3th pwm to manual mode
on a f8000 IC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The MSI MS-7031 is based on an ATI IXP300 south bridge. On this south
bridge, accessible I/O ports must be enabled explicitly. Unfortunately
the BIOS forgets to enable access to the hardware monitoring chip I/O
ports, so hardware monitoring fails.
Add a quirk enabling access to the required ports (0x295-0x296). This
is exactly what MSI's own hardware monitoring application is doing, so
it has to be the right way.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the new incarnation of the Winbond/Nuvoton W83627DHG
chip known as W83627DHG-P. It is basically the same as the original
W83627DHG with an additional automatic can speed control mode (not
supported by the driver yet.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Madhu <madhu.chinakonda@gmail.com>
This adds support for TI's TMP411 sensor chip.
Preliminary support were done by Gabriel Konat, Sander Leget and
Wouter Willems. The chip is compatible with TI's TMP401 sensor
chip. It has additional support for historical minimun/maximum
measurements.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a new hwmon driver for TI's TMP401 temperature sensor IC. This driver
was written on behalf of an embedded systems vendor under the
Linux driver project.
It has been tested using a TI TMP401 sample attached to a i2c-tiny-usb adapter.
Which was provided by Till Harbaum, many thanks to him for this!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enable auto-probing for the HC10 blade and amend the supported system
list.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make sure __devexit and devexit_p() match in all hwmon drivers.
Suggested by a similar fix from Mike Frysinger.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 360782dde0 (hwmon: (w83781d) Stop
abusing struct i2c_client for ISA devices) broke W83782D support for
devices connected on the ISA bus. You will hit a NULL pointer
dereference as soon as you read any device attribute. Other devices,
and W83782D devices on the SMBus, aren't affected.
Reported-by: Michel Abraham
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Abraham
atk_sensor_type is only used when DEBUG is defined.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf
These sensors communicate over a 2 wire bus running a device specific
protocol. The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available. This is handled by
an interrupt that is disabled under all other conditions.
I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!
Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem. If not it should be provided in the
platform data.
I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Matthew Palmer <mpalmer@debian.org>
Signed-off-by: Laurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.
There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).
Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy i2c binding model is going away really soon now, so convert
the lm95241 driver to the new binding model or it will break.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
Make use of the new abstraction layer and add a new transport layer for
spi. Works fine on a PXA based board.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This solves the dependency between lis3lv02d.[ch] and ACPI specific
methods. It introduces a ->bus_priv pointer to the device struct which is
casted to 'struct acpi_device' in the ACIP layer. Changed hp_accel.c
accordingly.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move lis3lv02d_init_device() down so that the forward declaration of
lis3lv02d_add_fs() becomes unnecessary.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have a laptop HP Compaq 8710W, I compiled into my kernel the LIS3LV02DL
and HP_ACCEL module drivers. While loading it cannot recognize the laptop
model, so i am sending the necessary information to update the database of
axis orientations.
>When the laptop is horizontal the position reported is about 0 for X and Y
>and a positive value for Z
Yes, it is about 0,0,1000, the actual reading says: (-17,-26,1018);
> If the left side is elevated, X increases (becomes positive)
Yes, X goes toward to positive 1000.
>If the front side (where the touchpad is) is elevated, Y decreases (becomes negative)
No, Y goes toward to positive 1000.
>If the laptop is put upside-down, Z becomes negative
Yes, the laptop on a table Z gives 1000, and if upsidedown the Z reads
-1000.
So in few words the Y axis is inverted.
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two more laptops to whitelist.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.
I have tested the driver with my board, and it appears to work fine. With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power. With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power. I'm not drawing any current at the
moment, so this is reasonable. The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.
I didn't attempt to support changing any of the chip's settings or
enabling the FET. I'm not sure even how to do that and still fit within
the hwmon framework. :)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An hwmon driver for the National Semiconductor LM95241 triple temperature
sensors chip
Signed-off-by: Davide Rizzo <elpa-rizzo@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Andrew noted, adev is pretty poor name for symbol being exported.
Rename it to lis3.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Cc: <Quoc.Pham@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many thanks to Fujitsu Siemens Computers for providing docs and a
machine to test the driver on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
At the moment, dmi_walk() lacks flexibility, users can't pass data to
the callback function. Add a pointer for private data to make this
function more flexible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Roland Dreier <rolandd@cisco.com>
Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.
If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
The pin for in6 and temp3 is shared on the W83667HG, so only one of
these features can be supported on any given system. Let the driver
select which one depending on the temp3 disabled bit.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.
At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use positive logic for fan pin variables (variable is set if pin is
used for fan), instead of negative logic which is error prone.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Gong Jun <JGong@nuvoton.com>
Fix for kernel.org bug #7154: hdaps inversion of actual Thinkpad
X41's Y-axis.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix for kernel.org bug #7154: hdaps inversion of each axis. This
version is based on the work from Michael Ruoss <miruoss@student.ethz.ch>.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Register access over SMBus isn't cheap, so avoid register access where
possible:
* Only write back the configuration register if it changed.
* Don't refresh the register cache when we don't have to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Fix a few oddities in how the ds1621 driver accesses the registers:
* We don't need a wrapper to access the configuration register.
* Check for error before calling swab16. Error checking isn't
complete yet, but that's a start.
* Device-specific read functions should never be called during
detection, as by definition we don't know what device we are talking
to at that point.
* Likewise, don't assume that register reads succeed during detection.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reorder the ds1621 driver code so that we can get rid of forward
function declarations.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
f75375_probe calls i2c_get_clientdata to initialize the data pointer,
but there isn't yet any client data to get, and the value is never
used before the variable is assigned a new value seven lines later.
The call doesn't hurt anything and wastes only a couple of cycles.
The reason to fix it is because this module serves as an example to
hackers writing new hwmon drivers, and this part of the example is
confusing.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver is reporting -128 degrees C as +128 degrees C.
That's not a terribly likely temperature value but let's still
get it right, especially when it simplifies the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update documentation to prevent further confusion/duplication.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix a logic bug reported by Roel Kluin, by rewriting the error
handling code in a clearer way.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The adt7468 chip supports VRM10 sensors just like the adt7463; add a
missing check for it.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The verstep check in the lm85 driver fails because the upper nibble of
the version register is 0x7, not 0x6, on the adt7468 chip. Probing of
all adt7468s was broken by 69fc1feba2
("hwmon: (lm85) Rework the device detection"), and this patch fixes
that. Also add in a missing i2c_device_id that accidentally got dropped
from the original patch.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for HP Pavilion dv5.
Since Intel-based models have an inverted x axis, while AMD-based models
have an inverted y axis, we introduce a new macro that special-cases axis
orientation based on two DMI entries: HP dv5 axis configuration is then
based on both the PRODUCT and BOARD name.
Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Cc: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Tested-by: Palatis Tseng <palatis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sensors responding with 0x3B to WHO_AM_I only have one data register per
direction, thus returning a signed byte from the position which is
occupied by the MSB in sensors responding with 0x3A.
Since multiple sensors share the reply to WHO_AM_I, we rename the defines
to better indicate what they identify (family of single and double
precision sensors).
We support both kind of sensors by checking for the sensor type on init
and defining appropriate data-access routines and sensor limits (for the
joystick) depending on what we find.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Acked-by: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds freefall handling to hp_accel driver. According to HP, it
should just work, without us having to set the chip up by hand.
hpfall.c is example .c program that parks the disk when accelerometer
detects free fall. It should work; for now, it uses fixed 20seconds
protection period.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a number of cases where things were not properly
cleaned up when acpi_check_resource_conflict() returned an error,
causing oopses such as the one reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=483208
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If the F71882FG chip is at address 0x4e, then the probe at 0x2e will
fail with the following message in the logs:
f71882fg: Not a Fintek device
This is misleading because there is a Fintek device, just at a
different address. So I propose to degrade this message to a debug
message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add support for the HP laptops of model 6710x for having correctly setup
axes.
Signed-off-by: Martin Kebert <gkmarty@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6730x for having correctly setup
axes.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6530x for having correctly setup
axes.
Reported-by: Jerome Poulin <jeromepoulin@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to dmesg my laptop model HP 6510b is not being recognized by this
driver. After I have modified "lis3lv02d.c" axes in Neverball are OK.
Signed-off-by: Jiri Tersel <tersel@mail.muni.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MacPro 3 have more temperature sensors than the previous MacPro's also the
sensor THTG has been removed. This patch add supports for the newer
temperature sensors in the MacPro3.
Signed-off-by: Bharath Ramesh <bramesh@vt.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) Fix CONFIG_DMI=n fallback to probe
hwmon: (abituguru3) Enable DMI probing feature on IN9 32X MAX
hwmon: (abituguru3) Match partial DMI board name strings
hwmon: Add a driver for the ADT7475 hardware monitoring chip
hwmon: (k8temp) Fix temperature reporting for (most) K8 RevG CPUs
hwmon: (k8temp) Fix wrong sensor selection for AMD K8 RevF/RevG CPUs
hwmon: (k8temp) Warn about fam F rev F errata
The LED on HP notebooks is connected through ACPI. That unfortunately
means that it needs to be delayed by using schedule_work() to avoid
calling the ACPI interpreter from an invalid context.
[akpm@linux-foundation.org: use flush_work() rather than sort-of reimplementing it]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver. From a purely Linux developer's point of view,
the led and the accelerometer have nothing related. However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module. Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The light sensors ALV0 and ALV1 on newer MacBooks (early 2008 and later)
changed to report 10 bytes instead the earlier 6, and the sensor encoding
subsequently changed. As a result, the reported light sensors readings
are much too low.
Via experiments leading up to this patch, it seems only the ALV0 is
reporting data, and the most useful value therein is a 10-bit big-endian
value at offset 6. This suggests that a new protocol was added as a
backward-compatible replacement on top of the old one.
This patch makes applesmc report the improved light sensor reading for the
new machines, on a scale in conformance with earlier ones.
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_DMI is not enabled, dmi detection should flag that no board
could be detected (err=1) rather than another error condition (err<0).
This fixes the fallback to manual probing for all motherboards, even
those without DMI strings, when CONFIG_DMI=n.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Switch the IN9 32X MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Paul Hartman <paul.hartman+gentoo@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The switch-over to using DMI board strings to identify abituguru3 compatible
mainboards works most of the time, but sometimes the vendor has substantially
modified the board string between BIOS revisions.
We have found that the vendor chipset identification string (provided in
brackets) changes frequently and is of no use to us. The rest of the board
string sometimes changes in subtle ways, e.g. whitespace or variations in
capitalization.
The new comparison code checks only a part of the supplied DMI board string,
trimming the bracketed content, whitespace, and ignoring case as necessary.
This fixes a bug where an IP35 Pro running an early BIOS would not be
detected without the force=1 module parameter, and also speculatively
fixes other similiar issues.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Nick Pasich <NewsLetters@nickandbarb.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Hwmon driver for the ADT7475 chip.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Current Temperature for K8 RevG desktop CPUs is a "normalized value"
which can be below ambient temperature.
As a consequence lots of RevG systems report temperatures like:
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +17 C
Core0 Temp: +3 C
Core1 Temp: +21 C
Core1 Temp: +5 C
being quite below ambient temperature.
There are even reports of negative temperature values.
This patch corrects the temperature reporting of k8temp for
RevG desktop CPUs.
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Meaning of ThermSenseCoreSel bit was inverted beginning with K8 RevF.
That means with current driver temp1/temp2 belong to core 1 and
temp3/temp4 belong to core 0 on a K8 RevF/RevG CPU.
This patch ensures that temp1/temp2 always belong to core 0 and
temp3/temp4 to core 1 for all K8 revisions.
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add warning about wrong CPU temperature readouts on all fam F rev F.
The allowed combinations of processors ensure that all processors
in a multisocket system have similar characteristics, e.g.
(1) provide temperature sensor interface (>=RevC && <RevF)
(2) are affected by erratum #141 (>=RevF)
Thus it is sufficient to check the revision of the boot CPU.
For "mixed silicon support" refer to
"Revision Guide for AMD Athlon 64 and AMD Opteron Processors" (RevA-E) and
"Revision Guide for AMD NPT Family 0Fh Processors" (RefF-G).
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sensor can be accessed via various buses. In particular, SPI, I²C
and, on HP laptops, via a specific ACPI API (the only one currently
supported). Separate this latest platform from the core of the sensor
driver to allow support for the other bus type. The second, and more
direct goal is actually to be able to merge this part with the
hp-disk-leds driver, which has the same ACPI PNP number.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (29 commits)
hwmon: Fix various typos
hwmon: Check for ACPI resource conflicts
hwmon: (lm70) Add TI TMP121 support
hwmon: (lm70) Code streamlining and cleanup
hwmon: Deprecate the fscher and fscpos drivers
hwmon: (fschmd) Add watchdog support
hwmon: (fschmd) Cleanups for watchdog support
hwmon: (i5k_amb) Load automatically on all 5000/5400 chipsets
hwmon: (it87) Add support for the ITE IT8720F
hwmon: Don't overuse I2C_CLIENT_MODULE_PARM
hwmon: Add LTC4245 driver
hwmon: (f71882fg) Fix fan_to/from_reg prototypes
hwmon: (f71882fg) Printout fan modes
hwmon: (f71882fg) Add documentation
hwmon: (f71882fg) Fix auto_channels_temp temp numbering with f8000
hwmon: (f71882fg) Add missing pwm3 attr for f71862fg
hwmon: (f71882fg) Add F8000 support
hwmon: (f71882fg) Remove the fan_mode module option
hwmon: (f71882fg) Separate max and crit alarm and beep
hwmon: (f71882fg) Check for hwmon powerdown state
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Check for ACPI resource conflicts in hwmon drivers. I've included
all Super-I/O and PCI drivers.
I've voluntarily left out:
* Vendor-specific drivers: if they conflicted on any system, this would
pretty much mean that they conflict on all systems, and we would know
by now.
* Legacy ISA drivers (lm78 and w83781d): they only support chips found
on old designs were ACPI either wasn't supported or didn't deal with
thermal management.
* Drivers accessing the I/O resources indirectly (e.g. through SMBus):
the checks are already done where they belong, i.e. in the bus drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution. This patch extends the
LM70 driver to support the TMP121. The TMP123 differs in pin assign-
ment.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).
Other fixes: doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that the new merged fschmd driver has gained support for the watchdog
integrated into these IC's, there is no more reason to keep the old fscher
and fscpos drivers around, so mark them as deprecated.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for the watchdog part found in _all_ supported FSC
sensor chips.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Various small cleanups in preparation of adding watchdog support,
mostly removing _MASK postfix from defines which are not masks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that we cannot create a pci_driver in this driver because PCI will
not call this module's probe function if the i5000-edac driver is already
loaded. That said, we only want one value (AMBASE) from the PCI config space.
Neither driver alters this value, so it's safe to read it. However, we still
want the module aliases, so provide that.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C_CLIENT_MODULE_PARM is overkill for force_subclients. We really
only use 4 out of the 48 slots, so we're better defining a custom
variable instead. This change saves 92 bytes of data for each of the
five drivers affected.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The RPM after conversion from / before conversion to a register value can be
much more than 65535 (up to 1500000), so putting this into an u16 can cause
overflows. This changes the functions to use an int to store / get RPM instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Print the mode (duty-cycle or RPM) of each fan on driver load.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add some documentation about the f71882fg driver, and update the Kconfig
documentation to report the new supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Adjust auto_channels_temp show and store functions for different numbering of
temps between f8000 and other supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
For some reason the fan_attr array for the f71862fg was missing the attr for
the 3th pwm output. This patch fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
And (finally) the patch actually adding f8000 support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the fan_mode module option it was a monstrosity to begin with, and
when adding support for the F8000 it becomes a real pain!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While studying the datasheets for adding F8000 support, I noticed that the
F718x2 has separate alarms (and beep control) for its max and crit limits.
We keep the temp#_alarm attributes as they are, even though it would be more
logical to rename them to temp#_max_alarm. Because lm_sensors v2 depends
on them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
More F8000 prep work. Take over the checking if the hwmon part is not
powered down from the standalone f8000 driver.
This check is valid for all supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Simplify fan and temp hyst. handling by treating the registers as an array of
nibbles instead of using switch cases. Also unify the way hysts are handled
between temp and fans, the temp code was storing the actual per temp hyst
values in 4 u8's, where as the fan code was storing actual register values.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on adding F8000 support I noticed that various of the
store sysfs functions (and a few of the show also) had issues.
This patch fixes the following issues in these functions:
* store: storing the result of strto[u]l in an int, resulting in a possible
overflow before boundary checking
* store: use of f71882fg_update_device(), we don't want to read the whole
device in store functions, just the registers we need
* store: use of cached register values instead of reading the needed regs
in the store function, including cases where f71882fg_update_device() was
not used, this could cause real isues
* show: shown value is a calculation of 2 or more cached register reads,
without locking the data struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch is a preparation patch for adding F8000 support to the f71882fg
driver. If you look at the register addresses and esp, the bits used for
the temperature channels, then you will notice that it appears that they
start at 1 in a system meant to start at 0. As the F8000 actually uses the 0
addresses and bits, this patch changes the f71882fg driver to take 4
temperatures numbered 0-3 in to account, using 1-3 in this new scheme for
the temperatures actually present in the F718x2FG.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The f71882fg driver did some io to ioports it hadn't reserved yet in its
find (detect) function, this patches moves this io to the probe function
where these ports are reserved and this io belongs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for the Fintek f71862fg superio monitoring
functions to the f71882fg driver.
This support has been tested without problems on a Jetway J9F2 by
Tony McConnell.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Various small cleanups as preparation for adding f71862fg support to the
f71882fg driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM (fan speed control) support to the f71882fg driver. Both
manual control and automatic (temperature-based) modes are supported.
Additionally, each mode has a PWM-based and an RPM-based variant. By
default we use the mode set by the BIOS.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
A few cleanups that were originally part of a larger patch but are
better submitted separately.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert f71882fg driver from SENSOR_ATTR to SENSOR_ATTR2 use, this is a
preparation patch for adding pwm support, which is broken out to make what
changes really in the pwm support patch clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add temperature sensor support for MacBook Air 2.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that the adt7470's automatic fan control algorithm only works
when the temperature sensors get updated. This in turn happens only when
someone tells the chip to read its temperature sensors. Regrettably, this
means that we have to drive the chip periodically.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The adt7470 driver currently assumes that 1s is the proper time to wait to
read all temperature sensors. However, the correct time is 200ms *
number_of_sensors. This patch sets the default time to provide for 10
sensors and then lowers it based on the number of sensor inputs that have
nozero values.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the small window that it takes to read the temperature sensors, the pwm
outputs momentarily drop to 0. This causes a noticeable hiccup in fan
speed, which is slightly annoying. The solution is to manually program
the pwm output with whatever the automatic value is and then shift the
fans to manual control while reading temperatures. Once that is done, put
the fans back to whatever mode of control was there before.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify some hwmon drivers to use DIV_ROUND_CLOSEST instead of bloating
source with (naughty) macros.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make use of the new dmi device loading support to automatically load the
applesmc driver based on the dmi_match table.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to analyze the SMC of the newer MacPros, applesmc needs to
recognize the machine. This patch adds the missing generic dmi_match
entry for MacPro models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 6.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Caleb Hyde <caleb.hyde@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/hwmon/lis3lv02d.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New driver to play with. As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors. This driver has been tested on an IntelliStation Z30.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard"). It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.
This driver was first written by Yan Burman. Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now). Pavel Machek removed few more features and switched locking from
semaphore to mutex.
Several people have contributed to the database of the axes.
[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Yan Burman <burman.yan@gmail.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The adt7468 is a follow-on to the adt7463, so plumb in adt7468 support
along the same code paths.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.
Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.
Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that if one registers a struct platform_device, the
platform device code expects that platform_device.device->driver points
to a struct driver inside a struct platform_driver.
This is not the case with the ipmi-si, ipmi-msghandler and ibmaem
drivers, which causes the suspend/resume hook functions to jump off into
nowhere, causing a crash. Make this assumption hold true for these
three drivers.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds accelerometer and temperature sensor support for Macbook 4.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 8.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Klaus Doblmann <klaus.doblmann@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerometer, backlight and temperature sensor support for the new
unibody Macbook Pro 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerometer, backlight and temperature sensor support for the new
unibody Macbook 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: David M. Lary <dmlary@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Ricky Campbell <johnrcampbell@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.
Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.
Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.
According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
There are several problems in the way the hysteresis value is handled
by the lm90 driver:
* In show_temphyst(), specific handling of the MAX6646 is missing, so
the hysteresis is reported incorrectly if the critical temperature
is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
the chip but data->temp_hyst isn't updated accordingly, so there is
a short period of time (up to 2 seconds) where the old hystereris
value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
to compute the value of the hysteresis register lacks
device-specific handling. As a result, the value of the hysteresis
register might be incorrect for the ADT7461 and MAX6646 chips.
Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
When w83781d is built-in, the final links fails with the following vague error
message:
`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o
w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The read fail ratio is sensitive to the delay between the first byte
written and the first byte read; apparently the sensors cannot be rushed.
Increasing the minimum wait time, without changing the total wait time,
improves the fail ratio from a 8% chance that any of the sensors fails in
one read, down to 0.4%, on a Macbook Air. On a Macbook Pro 3,1, the
effect is even more apparent. By reducing the number of status polls, the
ratio is further improved to below 0.1%. Finally, increasing the total
wait time brings the fail ratio down to virtually zero.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Bob McElrath <bob@mcelrath.org>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for Macbook Pro 3.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds temperature sensor support for the Macbook Pro 4.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dmi_system_id.driver_data is already void*.
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds accelerometer, backlight and temperature sensor support
for the Macbook Air.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some recent Macbooks, the package length for the light sensors ALV0 and
ALV1 has changed from 6 to 10. This patch allows for a variable package
length encompassing both variants.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The time to wait for a status change while reading or writing to the SMC
ports is a balance between read reliability and system performance. The
current setting yields rougly three errors in a thousand when
simultaneously reading three different temperature values on a Macbook
Air. This patch increases the setting to a value yielding roughly one
error in ten thousand, with no noticable system performance degradation.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On many Macbooks since mid 2007, the Pro, C2D and Air models, applesmc
fails to read some or all SMC ports. This problem has various effects,
such as flooded logfiles, malfunctioning temperature sensors,
accelerometers failing to initialize, and difficulties getting backlight
functionality to work properly.
The root of the problem seems to be the command protocol. The current
code sends out a command byte, then repeatedly polls for an ack before
continuing to send or recieve data. From experiments leading to this
patch, it seems the command protocol never quite worked or changed so that
one now sends a command byte, waits a little bit, polls for an ack, and if
it fails, repeats the whole thing by sending the command byte again.
This patch implements a send_command function according to the new
interpretation of the protocol, and should work also for earlier models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At one single place in the code, the specified number of bytes to read and
the actual number of bytes read differ by one. This one-liner patch fixes
that inconsistency.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds therm-min/max/crit-alarm callbacks, sensor-device-attribute
declarations, and refs to those new decls in the macro used to initialize
the therm_group (of sysfs files)
The thermistors use voltage channels to measure; so they don't have a
fault-alarm, but unlike the other voltages, they do have an overtemp,
which we call crit (by convention).
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
temp and vin status register values may be set by chip specifications, set
again by bios, or by this previously loaded driver. Debug output nicely
displays modprobe init=\d actions.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver handles 3 logical devices in fixed length array. Give this a
define-d constant.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds temp-min/max/crit/fault-alarm callbacks, sensor-device-attribute
declarations, and refs to those new decls in the macro used to initialize
the temp_group (of sysfs files)
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds vin-min/max-alarm callbacks, sensor-device-attribute declarations,
and refs to those new decls in the macro used to initialize the vin_group
(of sysfs files)
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring hwmon/pc87360 into agreement with
Documentation/hwmon/sysfs-interface.
Patchset adds separate limit alarms for voltages and temps, it also adds
temp[123]_fault files. On my Soekris, temps 1,2 are unused/unconnected,
so temp[123]_fault = 1,1,0 respectively. This agrees with
/usr/bin/sensors, which has always shown them as OPEN. Temps 4,5,6 are
thermistor based, and dont have a fault bit in their status register.
This patch:
2 different kinds of constants added:
- CHAN_ALM_* constants for (later) vin, temp alarm callbacks.
- CHAN_* conversion constants, used in _init_device, partly for RW1C bits
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.
Signed-off-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.
[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for pwm_enable.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM manual control.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not
create their sysfs-interface.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.
This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Rework the device detection to make it clearer and faster in the
general case (when a known device is found.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Simplify the IRQ handling routine of ams driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a separate mutex to serialize input device creation/removal,
otheriwse we deadlock if we try to remove input device while it is
being polled. Also do not take ams_info.lock when it is not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We should not allow writes to the 'joystick' module parameters since
writing there will not trigger creation of the input device. Disable
writes since we provide alternative way of enabling input device via
AMS device's sysfs attribute.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy i2c binding model is phasing out, so the ams driver needs
to be converted to a new-style i2c driver. Here is a naive approach of
this conversion. Basically it is moving the i2c device creation from
the ams driver to the i2c-powermac driver. This should work, but I
suspect we could come up with something cleaner by declaring the i2c
device as part of the platform setup. This could be done later by
someone more familiar with openfirmware-based platforms than I am
myself.
One nice thing brought by this conversion is that the ams driver
should be loaded automatically on systems where is is needed (at
least when the I2C interface to the chip is used) providing
coldplug-aware user-space environment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lm87 driver normally assumes that firmware configured the chip
correctly. Since this is not always the case, alllow platform code to
set the channel register value via platform_data. All other
configuration registers can be changed after driver initialisation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This means that if we have to start the monitor when probed, we also
stop it on removal.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
lm87_init_client() conditionally sets the Start bit and clears the
INT#_Clear bit in the Config 1 register. The condition should be that
either of these bits needs changing, but currently it checks the
(self-clearing) Initialization bit instead of INT#_Clear.
Fix the condition and also ensure we never set the Initialization bit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Degrade the "Unsupported chip" message from info to debug level.
There's nothing wrong with this, so no need to bother the user.
Also make the message slightly more descriptive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The encoding of temperatures varies between chips and modes. So do not
use "temp1" or "temp2" in the names of the conversion functions, but
specify the encoding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC. Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Use static functions instead of the TEMPx_FROM_REG* and TEMPx_TO_REG*
macros. This will ensure type safety and eliminate any side effects
from arguments passed in since the macros referenced 'val' multiple
times. This change should not affect functionality.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The Maxim chips supported by the lm90 driver have 8-bit high and low
remote limit values, not 11-bit as the other chips have. So stop reading
from and writing to registers that do not exist on these chips. Also
round the limit values set by the user properly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
Move the code which aggregates two 8-bit register values into a 16-bit
value to a separate function. We'll need to do it a second time soon and
I don't want to duplicate the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
The new-style dme1737 driver implements the optional detect() callback
to cover the use cases of the legacy driver. I don't actually expect
any new-style device for that driver, but as the old i2c API is going
away soon, we have to switch to the new one.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
The dme1737 driver support both LPC (ISA) and SMBus devices. At the
moment it's rather i2c-centric, and LPC variants use a fake i2c_client
for some operations.
In a near future, i2c_client will be allocated by i2c-core rather than
by the device drivers, so non-i2c drivers will not have one. As a
preparation step, change the driver code to no longer assume that
an i2c_client structure is always available. No functional change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
Enable driver checking of the DMI product name (when enabled) on
an Abit AT8 32X, instead of falling back to a manual probe. This
eliminates false negatives and eventually will help avoid
unnecessary bus probes on unsupported mainboards.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The table for the Abit AT8 32X was incorrectly missing an entry
for the sixth ("AUX3") fan. Add this entry, exporting the fan
reading to userspace.
Closes lm-sensors.org ticket #2339.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is not generic, and is added here for backward compatibility.
It is made an individual commit here to make it easier for revert
once the sharpsl_pm gets generic enough.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Driver based on corgi_ssp.c and sharpsl_pm.c, previously done by Richard
Purdie and many others.
Now changed to generic HWMON device and expose all the ADC input value
through sysfs.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch makes the needlessly global ad7414_update_device() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The IT8712F v0.9.1 datasheet applies to revisions >= 0x8 (J).
The driver was incorrectly attempting to enable 16-bit fan
readings on rev 0x7 (I) which led to incorrect RPM values.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Tested-by: John Gumb <john.gumb@tandberg.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The atxp1 device detection code has a major logic flaw, fix it. Not
sure how we managed to miss this when the driver was merged...
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Sebastian Witt <se.witt@gmx.net>
This is a PIC16F747 based controller that monitors and consolidates
the hardware access to various fan and temperature values reported by
adr7462 and similar devices behind an I2C bus.
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all AMD K8 have 6 VID pins, contrary to what was assumed in
commit 116d0486bd. This commit broke
support of older CPU models which have only 5 VID pins:
http://bugzilla.kernel.org/show_bug.cgi?id=11329
We need two entries in the hwmon-vid table, one for 5-bit VID models
(K8 revision <= E) and one for 6-bit VID models (K8 revision >= F).
This fixes bug #11329.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Frank Myhr <fmyhr@fhmtech.com>
Tested-by: Jean-Luc Coulon <jean.luc.coulon@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add in the CPUID for Nehalem chips.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all sensors are read when the energy meter is queried via
sysfs. This introduces a considerable amount of delay and variation in
the sysfs reading, which is not desirable when trying to profile energy
use. Therefore, read only the energy meters when a sysfs query comes in
for them, and don't cache the results so that we always get the latest
reading.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On older machines, probing for a nonexistent AEM interface returned an
IPMI error; when we saw this, we'd stop probing. On the x3650 M2 and
(presumably) later, we are returned a value indicating success and a
buffer full of garbage or zeroes. This causes the probe function to run
in an infinite loop. To fix this, we add one last check--if the
interface number we're looking for is higher than the number of
interfaces that AEM claims to have, stop probing.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously the driver was only using DMI to prevent smbus probing on
non-Abit motherboards. However, since the manual probing method is
brittle and prone to failure on some Abit motherboards (esp. the Abit
IP35 Pro) it is better to use DMI to also read the board name and then
decide whether or not to probe the bus.
At the moment, we do not have a list of valid DMI name strings to use
for existing and supported motherboards. This patch only implements DMI
probing for the IP35 Pro. For motherboards that can not yet use DMI
probing, a warning will be printed to the kernel log asking those users
to email me their dmidecode output.
The existing manual probing mechanism will be used if CONFIG_DMI is not
enabled, if DMI probing fails (for DMI-unsupported motherboards), or if
DMI probing fails and the "force" option is set (for DMI-supported
motherboards). Ideally in the longer term this manual probing method
would be removed.
This patch should be safe to apply as it does not change the probing
behaviour for most of the supported motherboards, just the IP35 Pro,
which already has regressions filed against it in 2.6.26.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11212
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the sensor -> channel/dimm mapping in tempX_label.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPI driver for analog to digital converters national semiconductor
ADC081S101, ADC124S501, ...
Code for 8 channels by Tobias Himmer.
This driver adds support for National Semiconductor ADC<bb><c>S<sss> chip
family, where:
* bb is the resolution in number of bits (8, 10, 12)
* c is the number of channels (1, 2, 4, 8)
* sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
kSPS and 101 for 1 MSPS)
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Cc: Tobias Himmer <tobias@himmer-online.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for Macbook v3 (sensors and accelerometer).
Signed-off-by: Nicolas Boichat <nicolas@boichat.ch>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for fans and temperature sensors on intel iMac.
Tested on iMac 24" 2.8ghz (iMac8,1), it supports the following sensors:
cpu A
ambient
gpu
gpu diode
gpu heatsink
hd bay 1
memory controller
optical drive
power
Signed-off-by: Roberto De Ioris <roberto@unbit.it>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop the legacy lm75 driver, and add a detect callback to the
new-style driver to achieve the same functionality.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
The it8705 chip supports 16-bit fan tachometers in revisions at least
>= 0x03 (Version G). This patch enables 16-bit fan readings on all
revisions >= 0x03 just like the it8712, it8716, and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it8712 chip supports 16-bit fan tachometers in revisions >= 0x07.
Revisions >= 0x08 dropped support for 8-bit fan divisor registers. The
patch enables 16-bit fan readings on all revisions >= 0x07 just like
the it8716 and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
AMD NPT 0Fh cpus use 6 bit VID codes. Successive codes with msb 0
describe 25mV decrements, while those with msb 1 describe 12.5mV
decrements. Existing hwmon-vid.c is correct only for codes with msb 0;
add support for the codes with msb 1.
Ref:
p 309, Table 71
AMD Publication 32559, BIOS and Kernel Developer's Guide for AMD NPT Family 0Fh Processors
http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/32559.pdf
Signed-off-by: Frank Myhr <fmyhr@fhmtech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Driver for the Analog Devices AD7414 temperature monitoring chip.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add critical temperature limits to the driver. These limits are read
only.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The adm9240 driver is in the kernel for three years now, time to
remove the EXPERIMENTAL dependency.
Signed-off-by: Grant Coady <gcoady.lk@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Drop the reset parameter of the w83627hf driver. It seems it wasn't
that useful. It was dropped from the Linux 2.4 version of this driver
back in July 2004.
The only users who have reported that they were still using this
parameter, needed it to switch the chip from automatic fan speed
control back to manual mode. Now that the driver creates pwmN_enable
sysfs files, users will be able to use these files instead, which is
way less agressive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dominik Geyer <dominik.geyer@gmx.de>
Adds support for pwm_enable sysfs interface for the w83627hf driver.
Signed-off-by: Dominik Geyer <dominik.geyer@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update w83791d with fan bits in vbat mon register (7.48 of the
datasheet). This change allows all fans to have a divisor of 128,
and fixes a problem with incorrectly reported fan speeds.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
These functions aren't used before being defined, so there's no point
in forward-declaring them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
and can't be programmed to fully turn off
- Different voltage scaling
- No VID input
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Skip the checking of the device ID register in the hwmon register
block if the force_id option is used.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix names of attribute structs to make them more consistent with the
rest of the code. Minor comment changes.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Clean up and simplify the device initialization function:
* Degrade error messages to warnings - what they really are.
* Stop warning about VxI mode, we don't really care.
* Drop comment about lack of limit initialization - that's the standard
way, all hardware monitoring drivers do that.
* Only read the configuration register once.
* Only write back to the configuration register if needed.
* Don't attempt to clear the lock bit, it locks itself to 1.
* Move the function to before it's called, so that we no longer need to
forware declare it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Misc cleanups to the lm85 hardware monitoring driver:
* Mark constant arrays as const.
* Remove useless masks.
* Have lm85_write_value return void - nobody is checking the returned
value anyway and in some cases it was plain wrong.
* Remove useless initializations.
* Rename new_client to client in lm85_detect.
* Replace cascaded if/else with a switch/case in lm85_detect.
* Group similar loops in lm85_update_device.
* Remove legacy comments.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
In set_pwm_auto_pwm_minctl, we write cached register bits back to the
chip. This is a bad idea as we have no guarantee that the cache is
up-to-date. Better read a fresh register value from the chip, it's
safer and in fact it is also more simple.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Drop a lot of useless register defines, conversion macros, data structure
members and update code. All these register values were read from the
device but nothing is done out of them, so this is all dead code in
practice.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix most style issues reported by checkpatch, including:
* Trailing, missing and extra whitespace
* Extra parentheses, curly braces and semi-colons
* Broken indentation
* Lines too long
I verified that the generated code is the same before and after
these changes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
More LM75 updates:
- Teach the LM75 driver to use new-style driver binding:
* Create a second driver struct, using new-style driver binding
methods cribbed from the legacy code.
* Add a MODULE_DEVICE_TABLE (for "newER-style binding")
* The legacy probe logic delegates its work to this new code.
* The legacy driver now uses the name "lm75_legacy".
- More careful initialization. Chips are put into 9-bit mode so
the current interconversion routines will never fail.
- Save the original chip configuration, and restore it on exit.
(Among other things, this normally turns off the mode where
the chip is constantly sampling ... and thus saves power.)
So the new-style code should catch all chips that boards declare,
while the legacy code catches others. This particular coexistence
strategy may need some work yet ... legacy modes might best be set
up explicitly by some tool not unlike "sensors-detect". (Or else
completely eradicated...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Minor cleanup and reorg of the lm75 code.
- Kconfig provides a larger list of lm75-compatible chips
- A top comment now says what the driver does (!) ... as in, just
what sort of sensor is this??
- Section comments now delineate the various sections of the driver:
hwmon attributes, driver binding, register access, module glue.
One driver binding function moved out of the attribute section,
as did the driver struct itself.
- Minor tweaks to legacy probe logic: correct a comment, and
remove a pointless variable.
- Whitespace, linelength, and comment fixes.
This patch should include no functional changes. It's preparation
for adding new-style (driver model) I2C driver binding.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
All the *_MAX_ADDR defines are never used, so remove them. The number
of registers of each type is already expressed by the *_COUNT defines.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch fixes a voltage scaling issue for the sch311x device.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds a module load parameter to enable probing of
non-standard LPC addresses 0x162e and 0x164e when scanning for supported
ISA chips.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch gets rid of a couple of macros previously used for sysfs attribute
generation and manipulation. This makes the source a little bigger but a lot
more readable and maintainable. It also fixes an issue with pwm5 & pwm6
attributes not being created read-only initially.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new-style w83l786ng driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Kevin Lo <kevlo@kevlo.org>
The new-style w83l785ts driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style w83793 driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style w83792d driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style w83791d driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
The new-style thmc50 driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
The new-style smsc47m192 driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hartmut Rick <linux@rick.claranet.de>
The new-style max6650 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans J. Koch <hjk@linutronix.de>
The new-style max1619 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alexey Fisher <fishor@mail.ru>
The new-style lm93 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Eric J. Bowersox <ericb@aspsys.com>
Cc: Carsten Emde <cbe@osadl.org>
Cc: Hans J. Koch <hjk@linutronix.de>
The new-style lm92 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style lm90 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style lm87 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
The new-style lm83 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style lm80 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style lm77 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andras Bali <drewie@freemail.hu>
The new-style lm63 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style gl520sm driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Maarten Deprez <maartendeprez@users.sourceforge.net>
The new-style gl518sm driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style fscpos driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style fschmd driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <j.w.r.degoede@hhs.nl>
The new-style fscher driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Reinhard Nissl <rnissl@gmx.de>
Drop the legacy f75375s i2c driver, and add a detect callback to the
new-style i2c driver to achieve the same functionality.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Riku Voipio <riku.voipio@movial.fi>
The new-style ds1621 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style atxp1 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style asb100 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style adt7473 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
The new-style adt7470 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
The new-style ads7828 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style adm9240 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Grant Coady <gcoady.lk@gmail.com>
The new-style adm1031 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alexandre d'Alton <alex@alexdalton.org>
The new-style adm1029 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
The new-style adm1026 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style adm1025 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style adm1021 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The ad7418 driver is only used on embedded platforms where i2c
devices can easily be declared in platform code. Thus a new-style
i2c driver makes perfect sense. This lets us get rid of quirky
detection code (these chips have no identification registers) and
shrinks the binary driver size by 38%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Adds R61, T61p, X61s, X61, Z61m, Z61p models to whitelist.
Fixes this:
cullen@lenny:~$ sudo modprobe hdaps
FATAL: Error inserting hdaps (/lib/modules/2.6.22-10-generic/kernel/drivers/hwmon/hdaps.ko): No such device
[25192.888000] hdaps: supported laptop not found!
[25192.888000] hdaps: driver init failed (ret=-19)!
Originally based on an Ubuntu patch that got it wrong, the dmidecode
output of the corresponding laptops shows LENOVO as the manufacturer.
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.22/+bug/133636
tested on X61s:
[ 184.893588] hdaps: inverting axis readings.
[ 184.893588] hdaps: LENOVO ThinkPad X61s detected.
[ 184.893588] input: hdaps as /class/input/input12
[ 184.924326] hdaps: driver successfully loaded.
Cc: Klaus S. Madsen <ubuntu@hjernemadsen.org>
Cc: Chuck Short <zulcss@ubuntu.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Murray