In preparation of factoring out PHY configuration to a separate source
file move commonly used definitions to new header file r8169.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename rtl_apply_firmware() to r8169_apply_firmware() before exporting
it to avoid namespace clashes with other drivers for Realtek hardware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the phy_device as parameter to rtl8168d_apply_firmware_cond(),
this avoids having to access rtl8169_private internals.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace rtl_writephy and rtl_readphy with the respective phylib
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move configuring EEE on MAC side out of the PHY configuration.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing this ERI register is a MAC setting, so move it to
rtl_hw_start_8106().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch rtl_writephy_batch() to phylib functions, as a result we can
avoid passing a rtl8169_private parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions use only the phy_device member of rtl8169_private,
so we can pass the phy_device as parameter directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions use only the phy_device member of rtl8169_private,
so we can pass the phy_device as parameter directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of factoring out rtl8169scd_hw_phy_config() move this
quirk to rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless debug statement. This also allows to remove the
net_device parameter from rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preperation of factoring out the PHY configuration to a separate
source file this patch:
- avoids accessing rtl8169_private internals by passing the phy_device
and mac_version as separate parameters
- renames rtl_hw_phy_config to r8169_hw_phy_config to avoid namespace
clashes with other drivers for Realtek hardware
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use constant EnAnaPLL for bit 14 as in vendor driver. The vendor
driver sets this bit for chip version 02 only, but I'm not aware of
any issues, so better leave it as it is.
In addition remove the useless debug message.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code by moving the call to rtl_enable_eee() from the
individual PHY configs to rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to recent changes we don't need the call to rtl_rar_exgmac_set()
and longer at this place. It's called from rtl_rar_set() which is
called in rtl_init_mac_address() and rtl8169_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and factor out this magic from rtl8168h_2_hw_phy_config()
and name it based on the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().
v2: fix referenced commit id
Fixes: 14012c9f3b ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 also requires to enable RX for WoL.
v2: add missing Fixes tag
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported [0] that network doesn't wake up on cable plug-in with
certain chip versions. Reason is that on these chip versions the PHY
doesn't detect cable plug-in when being in power-down mode. So prevent
the PHY from powering down if WoL is enabled.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 95fb8bb318 ("net: phy: force phy suspend when calling phy_stop")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan reported [0] that network is broken since the referenced commit
when using jumbo frames. This commit isn't wrong, it just revealed
another issue that has been existing before. According to the vendor
driver the RTL8168e-specific jumbo config doesn't apply for RTL8168evl.
[0] https://lkml.org/lkml/2019/11/30/119
Fixes: 4ebcb113ed ("r8169: fix jumbo packet handling on resume from suspend")
Reported-by: Alan J. Wylie <alan@wylie.me.uk>
Tested-by: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
During performance testing, I found that one of my r8169 NICs suffered
a major performance loss, a 8168c model.
Running netperf's TCP_STREAM test didn't return the expected
throughput of > 900 Mb/s, but rather only about 22 Mb/s. Strange
enough, running the TCP_MAERTS and UDP_STREAM tests all returned with
throughput > 900 Mb/s, as did TCP_STREAM with the other r8169 NICs I can
test (either one of 8169s, 8168e, 8168f).
Bisecting turned up commit 93681cd7d9,
"r8169: enable HW csum and TSO" as the culprit.
I added my 8168c version, RTL_GIGA_MAC_VER_22, to the code
special-casing the 8168evl as per the patch below. This fixed the
performance problem for me.
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load Realtek-provided firmware for RTL8168fp/RTL8117. Unlike the
firmware for other chip versions which is for the PHY, firmware for
RTL8168fp/RTL8117 is for the MAC.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using constant MII_EXPANSION is misleading here because register 0x06
has a different meaning on page 0x0005. Here a proprietary PHY
parameter is read by writing the parameter id to register 0x05 on page
0x0005, followed by reading the parameter value from register 0x06.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use r8168d_modify_extpage() also in rtl8168f_config_eee_phy() to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for chip version RTL8117. Settings have been copied from
Realtek's r8168 driver, there however chip ID 54a belongs to a chip
version called RTL8168FP. It was confirmed that RTL8117 works with
Realtek's driver, so both chip versions seem to be the same or at
least compatible.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if network is re-started, we advertise all supported EEE
modes, thus potentially overriding a manual adjustment the user made
e.g. via ethtool. Be friendly to the user and preserve a manual
setting on network re-start.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8168c_4_hw_phy_config() duplicates rtl8168c_3_hw_phy_config(),
so we can remove the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain integrated PHY's from RTL8168d support extended pages. On page
0x0007 the number of the extended page is written to register 0x1e,
then the registers on the extended page can be accessed. Add a helper
for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the phylib MDIO access functions in more places to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168d support an indirect access method for
PHY parameters. On page 0x0005 parameter number is written to register
0x05, then the parameter can be accessed via register 0x06.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168g support an indirect access method for
PHY parameters. On page 0x0a43 parameter number is written to register
0x13, then the parameter can be accessed via register 0x14.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions like phy_modify_paged() read the current page, on Realtek
PHY's this means reading the value of register 0x1f. Add special
handling for reading this register, similar to what we do already
in r8168g_mdio_write(). Currently we read a random value that by
chance seems to be 0 always.
Fixes: a2928d2864 ("r8169: use paged versions of phylib MDIO access functions")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in [0] at least one RTL8168dp version has problems
establishing a link. This chip version has an integrated RTL8211b PHY,
however the chip seems to report a wrong PHY ID, resulting in a wrong
PHY driver (for Generic Realtek PHY) being loaded.
Work around this issue by adding a hook to r8168dp_2_mdio_read()
for returning the correct PHY ID.
[0] https://bbs.archlinux.org/viewtopic.php?id=246508
Fixes: 242cd9b586 ("r8169: use phy_resume/phy_suspend")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One place in the driver was left where the open-coded functionality
hasn't been replaced with helper rtl_hw_aspm_clkreq_enable yet.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have only one user of the error path, so we can inline it.
In addition the call to rtl8169_make_unusable_by_asic() can be removed
because rtl8169_alloc_rx_data() didn't call rtl8169_mark_to_asic() yet
for the respective index if returning NULL.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aligns the fix_features callback with the vendor driver and
also disables IPv6 HW checksumming and TSO if jumbo packets are used
on RTL8101/RTL8168/RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting PCI_EXP_DEVCTL_NOSNOOP_EN for certain chip versions had been
added to the vendor driver more than 10 years ago, and copied from
there to r8169. It has been removed from the vendor driver meanwhile
and I think we can safely remove this too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove rtl_hw_start_8168bef() and use rtl_hw_start_8168b()
instead because setting register Config4 is done in
rtl_jumbo_config(), being called from rtl_hw_start().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
We can remove rtl_hw_start_8168dp() because it's the same as
rtl_hw_start_8168dp() now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
r8168b_0_hw_jumbo_enable() and r8168b_0_hw_jumbo_disable() both do the
same and just set PCI_EXP_DEVCTL_NOSNOOP_EN. We can simplify the code
by moving this setting for RTL8168B to rtl_hw_start_8168().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The attempt to improve performance by changing the PCIe max read request
size was added in the vendor driver more than 10 years back and copied
to r8169 driver. In the vendor driver this has been removed long ago.
Obviously it had no effect, also in my tests I didn't see any
difference. Typically the max payload size is less than 512 bytes
anyway, and the PCI core takes care that the maximum supported value
is set. So let's remove fiddling with PCIe max read request size from
r8169 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Mariusz reported that invalid packets are sent after resume from
suspend if jumbo packets are active. It turned out that his BIOS
resets chip settings to non-jumbo on resume. Most chip settings are
re-initialized on resume from suspend by calling rtl_hw_start(),
so let's add configuring jumbo to this function.
There's nothing wrong with the commit marked as fixed, it's just
the first one where the patch applies cleanly.
Fixes: 7366016d2d ("r8169: read common register for PCI commit")
Reported-by: Mariusz Bialonczyk <manio@skyboo.net>
Tested-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
RTL8125 uses a different register for VLAN offloading config,
therefore don't set bit RxVlan.
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds EEE support for RTL8125 based on the vendor driver.
Supported is EEE for 100Mbps and 1Gbps. Realtek recommended to not yet
enable EEE for 2.5Gbps due to potential compatibility issues. Also
ethtool doesn't support yet controlling EEE for 2.5Gbps and 5Gbps.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PHY initialization magic copied from the r8125 vendor
driver. In addition it supports loading the firmware for chip version
RTL_GIGA_MAC_VER_61.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for 2.5Gbps chip RTL8125, it's partially based on the
r8125 vendor driver. Tested with a Delock 89531 PCIe card against a
Netgear GS110MX Multi-Gig switch. Firmware isn't strictly needed,
but on some systems there may be compatibility issues w/o firmware.
Firmware has been submitted to linux-firmware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On RTL8125 this bit is always cleared after send. Therefore check for
tx_skb->skb being set what is functionally equivalent.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 uses a different register number for IntrMask.
To net have side effects by reading a random register let's
use a register that is the same on all supported chip families.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 doesn't support the same coalescing registers, therefore move
this initialization to the 8168/6169-specific init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8125 we will have to read the MAC address also from another
register range, therefore create a small helper.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend helper rtl_is_8168evl_up to properly work once we add
mac version numbers >51 for RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 uses a 32 bit interrupt mask even though only bits in the
lower 16 bits are used. Change interrupt mask size to u32 to be
prepared and reintroduce helper rtl_get_events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the call to dma_sync_single_for_cpu after calling napi_alloc_skb.
This avoids calling dma_sync_single_for_cpu w/o handing control back
to device if the memory allocation should fail.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Aaro this patch causes network problems on
MIPS Loongson platform. Therefore revert it.
Fixes: f072218cca ("r8169: remove not needed call to dma_sync_single_for_device")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync EEE init for RTL8168h with vendor driver and add two writes to
vendor-specific registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Realtek PHY driver maps the vendor-specific EEE registers
to the standard MMD registers, we can remove all special handling and
use the generic functions phy_ethtool_get/set_eee.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger reported sporadic transmit timeouts and it turned out that one
path misses ringing the doorbell. Fix was suggested by Eric.
Fixes: ef14358546 ("r8169: make use of xmit_more")
Suggested-by: Eric Dumazet <edumazet@google.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_free_rx_databuff is used in only one place, so let's inline it.
We can improve the loop because rtl8169_init_ring zero's RX_databuff
before calling rtl8169_rx_fill, and rtl8169_rx_fill fills
Rx_databuff starting from index 0.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling TSO but leaving SG active results is a significant
performance drop. Therefore disable also SG on RTL8168evl.
This restores the original performance.
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate 16kb per rx buffer, so we can avoid some overhead by using
alloc_pages_node directly instead of bothering kmalloc_node. Due to
this change buffers are page-aligned now, therefore the alignment check
can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize PCIe PHY initialization with vendor driver version 8.047.01.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for MAC OCP read-modify-write operations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code piece was inherited from RTL8139 code, the register at
address 0x5c however has a different meaning on RTL8169 and is unused.
So we can remove this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a previous attempt to use xmit_more, but the change had to be
reverted because under load sometimes a transmit timeout occurred [0].
Maybe this was caused by a missing memory barrier, the new attempt
keeps the memory barrier before the call to netif_stop_queue like it
is used by the driver as of today. The new attempt also changes the
order of some calls as suggested by Eric.
[0] https://lkml.org/lkml/2019/2/10/39
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that after resuming from suspend network fails with
error "do_IRQ: 3.38 No irq handler for vector", see [0]. Enabling WoL
can work around the issue, but the only actual fix is to disable MSI.
So let's mimic the behavior of the vendor driver and disable MSI on
all chip versions before RTL8168d.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=204079
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Reported-by: Dušan Dragić <dragic.dusan@gmail.com>
Tested-by: Dušan Dragić <dragic.dusan@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a6851c613f.
It was reported that RTL8111b successfully finishes 1000/Full autoneg
but no data flows. Reverting the original patch fixes the issue.
It seems to be a HW issue with the integrated RTL8211B PHY. This PHY
version used also e.g. on RTL8168d, so better revert the original patch.
Reported-by: Bernhard Held <berny156@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable HW csum and TSO per default except on known buggy chip versions.
Realtek confirmed that RTL8168evl has a HW issue with TSO.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loop in r8169_csum_workaround is called only if in
msdn_giant_send_check a copy of the skb header needs to be made and
we don't have enough memory. Let's simply drop the packet in that case
so that we can remove r8169_csum_workaround.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement callback ndo_features_check and move all feature checks there.
This will allow us to get rid of r8169_csum_workaround() completely in
a subsequent step. Like in the vendor driver disable HW csum for short
packets on RTL8168b.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set GSO max size and max segment number as in the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align setting PME with the vendor driver. PMEnable is writable on
RTL8169 only, on later chip versions it's read-only. PME_SIGNAL is
used on chip versions from RTL8168evl with the exception of the
RTL8168f family.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves and simplifies rtl_set_rx_mode a little.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "additonal" by "additional" in a comment.
Typo found by checkpatch.pl.
Signed-off-by: Corentin Musard <corentinmusard@gmail.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves few aspects of rtl_rx, no functional change intended.
1. inline rtl8169_try_rx_copy
2. make pkt_size unsigned
3. use constant ETH_FCS_LEN instead of value 4
4. We just created the skb, so we don't need the checks in skb_put.
Also we don't need the return value of skb_put.
Set skb->tail and skb->len directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a copy&paste error in the original patch. Setting the wrong
register resulted in massive packet loss on some systems.
Fixes: a2928d2864 ("r8169: use paged versions of phylib MDIO access functions")
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On RTL8411b the RX unit gets confused if the PHY is powered-down.
This was reported in [0] and confirmed by Realtek. Realtek provided
a sequence to fix the RX unit after PHY wakeup.
The issue itself seems to have been there longer, the Fixes tag
refers to where the fix applies properly.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1692075
Fixes: a99790bf5c ("r8169: Reinstate ASPM Support")
Tested-by: Ionut Radu <ionut.radu@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch syncs the name of few chip versions with the latest vendor
driver version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that the GPD MicroPC is broken in a way that no valid
MAC address can be read from the network chip. The vendor driver deals
with this by assigning a random MAC address as fallback. So let's do
the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 759d095741.
The patch was based on a misunderstanding. As Al Viro pointed out [0]
it's simply wrong on big endian. So let's revert it.
[0] https://marc.info/?t=156200975600004&r=1&w=2
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA_API_HOWTO.txt includes an example explaining when
dma_sync_single_for_device() is not needed, and that example matches
our use case. The buffer isn't changed by the CPU and direction is
DMA_FROM_DEVICE, so we can remove the call to
dma_sync_single_for_device().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/DMA-API-HOWTO.txt states:
By default, the kernel assumes that your device can address 32-bits of
DMA addressing. For a 64-bit capable device, this needs to be increased,
and for a device with limitations, it needs to be decreased.
Therefore we don't need the 32 Bit DMA fallback configuration and can
remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN tag is stored in the descriptor in network byte order.
Using swab16 works on little endian host systems only. Better play safe
and use ntohs or htons respectively.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain chip version / board combinations have massive problems if
ASPM is active. If BIOS enables ASPM and doesn't let OS control it,
then we may have a problem with the current code. Therefore check the
return code of pci_disable_link_state() and don't enable ASPM in the
network chip if OS can't control ASPM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Abit Fatal1ty F-190HD has a PCI ID quirk and the entry marks this
board as not GBit-capable, what is wrong. According to [0] the board
has a RTL8111B that is GBit-capable, therefore remove the
RTL_CFG_NO_GBIT flag.
[0] https://www.centos.org/forums/viewtopic.php?t=23390
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From RTL8168e-vl the value in register MaxTxPacketSize is interpreted
differently, therefore use new helper rtl_is_8168evl_up to set this
register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper rtl_is_8168evl_up to make the code better readable and to
simplify it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tp->coalesce_info is used in rtl_coalesce_info() only, so we can
remove this member. In addition replace phy_ethtool_get_link_ksettings
with a direct access to tp->phydev->speed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a timeout currently ~0 is returned. Callers often just check
whether a certain bit is set and therefore may behave incorrectly.
So let's return -ETIMEDOUT in case of a timeout.
r8168_phy_ocp_read is used in r8168g_mdio_read only, therefore we can
apply the same change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code by removing struct rtl_cfg_info. Only info we need
per PCI ID is whether it supports GBit or not.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prepare removal of struct rtl_cfg_info, set the coalesce
config based on the chip version number.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the latest changes we don't need separate functions
rtl_hw_start_8168 and rtl_hw_start_8101 any longer. This allows us to
simplify the code. For this change we need to move rtl_hw_start() and
rtl_hw_start_8169(). rtl_hw_start_8169() is unchanged.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPCMD_QUIRK_MASK isn't specific to certain chip versions. The vendor
driver applies this mask to all 8168 versions. Therefore remove QUIRK
from the mask name and apply it on all chip versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far several places in the code deal with setting the interrupt mask
for the respective chip versions. Improve this by having one function
for this only. In addition don't set RxFIFOOver for all 8101 chip
versions like in the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The opts[] array is of type u32. Therefore remove the wrong
cpu_to_le32(). The opts[] array members are converted to little endian
later when being assigned to the respective descriptor fields.
This is not a new issue, it just popped up due to r8169.c having
been renamed and more thoroughly checked. Due to the renaming
this patch applies to net-next only.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's factor out firmware handling into a separate source code file.
This simplifies reading the code and makes clearer what the interface
between driver and firmware handling is.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of factoring out firmware handling rename r8169.c to
r8169_main.c.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit