Core changes:
- Retired the old set-up function for GPIO IRQ chips. All chips
now use the template struct gpio_irq_chip and pass that to the core
to be set up alongside the gpio_chip. We can finally get rid of
the old cruft.
- Some refactoring and clean up of the core code.
- Support edge event timestamps to be stamped using REALTIME
(wall clock) timestamps. We have found solid use cases for
this, so we support it.
New drivers:
- MStar MSC313 GPIO driver.
- HiSilicon GPIO driver.
Driver improvements:
- The PCA953x driver now also supports the NXP PCAL9554B/C chips.
- The mockup driver can now be probed from the device tree which
is pretty useful for virtual prototyping of devices.
- The Rcar driver now supports .get_multiple()
- The MXC driver dropped some legacy and became a pure device
tree client.
- The Exar driver was moved over to the IDA interface for
enumerating, and also switched over to using regmap for
register access.
-----BEGIN PGP SIGNATURE-----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=nrFU
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.11 kernel cycle:
Core changes:
- Retired the old set-up function for GPIO IRQ chips. All chips now
use the template struct gpio_irq_chip and pass that to the core to
be set up alongside the gpio_chip. We can finally get rid of the
old cruft.
- Some refactoring and clean up of the core code.
- Support edge event timestamps to be stamped using REALTIME (wall
clock) timestamps. We have found solid use cases for this, so we
support it.
New drivers:
- MStar MSC313 GPIO driver.
- HiSilicon GPIO driver.
Driver improvements:
- The PCA953x driver now also supports the NXP PCAL9554B/C chips.
- The mockup driver can now be probed from the device tree which is
pretty useful for virtual prototyping of devices.
- The Rcar driver now supports .get_multiple()
- The MXC driver dropped some legacy and became a pure device tree
client.
- The Exar driver was moved over to the IDA interface for
enumerating, and also switched over to using regmap for register
access"
* tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
MAINTAINERS: Remove reference to non-existing file
gpio: hisi: Do not require ACPI for COMPILE_TEST
MAINTAINERS: Add maintainer for HiSilicon GPIO driver
gpio: gpio-hisi: Add HiSilicon GPIO support
gpio: cs5535: Simplify the return expression of cs5535_gpio_probe()
gpiolib: irq hooks: fix recursion in gpiochip_irq_unmask
dt-bindings: mt7621-gpio: convert bindings to YAML format
gpiolib: cdev: Flag invalid GPIOs as used
gpio: put virtual gpio device into their own submenu
drivers: gpio: amd8111: use SPDX-License-Identifier
drivers: gpio: amd8111: prefer dev_err()/dev_info() over raw printk
drivers: gpio: bt8xx: prefer dev_err()/dev_warn() over of raw printk
gpio: Add TODO item for debugfs interface
gpio: just plain warning when nonexisting gpio requested
tools: gpio: add option to report wall-clock time to gpio-event-mon
tools: gpio: add support for reporting realtime event clock to lsgpio
gpiolib: cdev: allow edge event timestamps to be configured as REALTIME
gpio: msc313: MStar MSC313 GPIO driver
dt-bindings: gpio: Binding for MStar MSC313 GPIO controller
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
...
- several refactoring patches of the core gpiolib code
- add support for NXP PCAL9554B/C to gpio-pca953x
- allow probing mockup devices from device tree
- refactoring and improvements to gpio-rcar
- improvements to locking in gpio-tegra
- code shrink in gpiolib devres
- get the irq offset from device tree in gpio-sifive
- major refactoring of gpio-exar
- convert gpio-mvebu pwm access to regmap
- create a new submenu for virtual GPIO drivers
- fix clang fall-through warnings treewide
- minor driver refactoring and tweaks sprinkled all over
-----BEGIN PGP SIGNATURE-----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=RmnM
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.11-rc1
- several refactoring patches of the core gpiolib code
- add support for NXP PCAL9554B/C to gpio-pca953x
- allow probing mockup devices from device tree
- refactoring and improvements to gpio-rcar
- improvements to locking in gpio-tegra
- code shrink in gpiolib devres
- get the irq offset from device tree in gpio-sifive
- major refactoring of gpio-exar
- convert gpio-mvebu pwm access to regmap
- create a new submenu for virtual GPIO drivers
- fix clang fall-through warnings treewide
- minor driver refactoring and tweaks sprinkled all over
In dwapb_get_reset(), if devm_reset_control_get_optional_shared() fails,
an error message is printed even if the failure is the benign
EPROBE_DEFER error due to the reset controller not yet being
initialized. Use dev_err_probe() to handle
devm_reset_control_get_optional_shared() errors to avoid unnecessarilly
printing an error message for the deferred probe error.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Commit 0ea683931a ("gpio: dwapb: Convert driver to using the
GPIO-lib-based IRQ-chip") missed the case in dwapb_irq_set_wake().
Without this fix, probing the dwapb gpio driver will hit a error:
"address between user and kernel address ranges" on a Ampere armv8a
server and cause a panic.
Fixes: 0ea683931a ("gpio: dwapb: Convert driver to using the GPIO-lib-based IRQ-chip")
Signed-off-by: Jia He <justin.he@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since the resource managed version of gpiochip_add_data() will handle the
GPIO-chip data automated cleanup we can freely remove the DW APB GPIO
driver code responsible for that. After doing so the DW APB GPIO driver
removal callback can be also fully discarded since there is nothing left
to be done for it. All the cleanups are now performed by means of the
device managed framework.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The kernel clock framework provides the resource managed version of
the clk_bulk_get() method. The only thing which needs to be also automated
is the clocks disable/unprepare procedure executed on the device removal.
It can be implemented by means of the custom action definition. After that
the clocks acquisition and release will be purely managed by the device
resources interface.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The reset control interface provides the resource managed version of
the reset_control_get() method. The only thing which needs to be also
automated is the reset lane assertion on the device removal. It can be
implemented by means of the custom action definition. After that the reset
control will be purely managed by the device resources interface.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since GPIOlib-based IRQ-chip interface is now utilized there is no need
in calling the methods acpi_gpiochip_{request,free}_interrupts() here.
They will be called from gpiochip_add_irqchip()/gpiochip_irqchip_remove()
anyway.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since GPIOlib-based IRQ-chip interface is now utilized there is no need in
setting up a custom GPIO-to-IRQ mapping method. GPIO-lib defines the
standard mapping method - gpiochip_to_irq(), which will be used anyway no
matter whether the custom to_irq callback is specified or not.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO-lib provides a ready-to-use interface to initialize an IRQ-chip on
top of a GPIO chip. It's better from maintainability and readability
point of view to use one instead of supporting a hand-written Generic
IRQ-chip-based implementation. Moreover the new implementation won't
cause much functional overhead but will provide a cleaner driver code.
All of that makes the DW APB GPIO driver conversion pretty much justified
especially seeing a tendency of the other GPIO drivers getting converted
too.
Here is what we do in the framework of this commit to convert the driver
to using the GPIO-lib-based IRQ-chip interface:
1) IRQ ack, mask and unmask callbacks are locally defined instead of
using the Generic IRQ-chip ones.
2) An irq_chip structure instance is embedded into the dwapb_gpio
private data. Note we can't have a static instance of that structure since
GPIO-lib will add some hooks into it by calling gpiochip_set_irq_hooks().
A warning about that would have been printed by the GPIO-lib code if we
used a single irq_chip structure instance for multiple DW APB GPIO
controllers.
3) Initialize the gpio_irq_chip structure embedded into the gpio_chip
descriptor. By default there is no IRQ enabled so any event raised will be
handled by the handle_bad_irq() IRQ flow handler. If DW APB GPIO IP-core
is synthesized to have non-shared reference IRQ-lines, then as before the
hierarchical and cascaded cases are distinguished by checking how many
parental IRQs are defined. (Note irq_set_chained_handler_and_data() won't
initialize IRQs, which descriptors couldn't be found.) If DW APB GPIO IP
is used on a platform with shared IRQ line, then we simply won't let the
GPIO-lib to initialize the parental IRQs, but will handle them locally in
the driver.
4) Discard linear IRQ-domain and Generic IRQ-chip initialization, since
GPIO-lib IRQ-chip interface will create a new domain and accept a standard
IRQ-chip structure pointer based on the setting we provided in the
gpio_irq_chip structure.
5) Manually select a proper IRQ flow handler directly in the
irq_set_type() callback by calling irq_set_handler_locked() method, since
an ordinary (not Generic) irq_chip descriptor is now utilized. Note this
shalln't give any regression
6) Alter CONFIG_GPIO_DWAPB kernel config to select
CONFIG_GPIOLIB_IRQCHIP instead of CONFIG_GENERIC_IRQ_CHIP.
Note neither 4) nor 5) shall cause a regression of commit 6a2f4b7dad
("gpio: dwapb: use a second irq chip"), since the later isn't properly
used here anyway.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a new macro DWAPB_MAX_GPIOS which defines the maximum possible number
of GPIO lines corresponding to the maximum DW APB GPIO controller port
width. Use the new macro instead of number literal 32 where it's
applicable.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For better readability let's group all the IRQ handlers in a single place
of the driver instead of having them scatter around all over the file.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Indeed generic GPIO DT-schema implies that number of GPIOs should be
described by the "ngpios" property located under a GPIO-provider DT node.
In that case it's redundant to have a vendor-specific "snps,nr-gpios"
property describing the same setting. Moreover it might be errors prone.
Since commit 93d2e4322a ("of: platform: Batch fwnode parsing when adding
all top level devices") the fwnode parsing is resumed after the vast
majority of the platform devices are added. Implicitly that commit
activates re-parsing of the whole device tree GPIOs-phandle properties
detected having "-gpio/-gpios" suffixes. Since the vendor-specific number
of GPIOs property is defined with "-gpios" suffix, then of_link_property()
will consider it as a suffix-property with "#gpio-cells" structure, which
obviously it doesn't have. As a result for two DW APB GPIO controllers
we'll have the next errors printed.
OF: /bus@1f059000/gpio@1f044000/gpio-port@0: could not find phandle
OF: /bus@1f059000/gpio@1f045000/gpio-port@0: could not get #gpio-cells for /opp-table
OF: /bus@1f059000/gpio@1f044000/gpio-port@0: could not find phandle
OF: /bus@1f059000/gpio@1f045000/gpio-port@0: could not get #gpio-cells for /opp-table
See, the kernel fwnode parsing procedure even tried to resolve the phandle
ID, which it thought was the opp-table DT-node, while in fact it was just
a number "32". What would happen if that magic number actually referred to
a GPIO DT-node with "#gpio-cells" property defined?..
In order to fix the problem let's mark the "snps,nr-gpios" property as
deprecated and add the generic "ngpios" property support with the same
purpose as the deprecated one. That and the errors log above shall
motivate the platform developer to convert the DW APB GPIO DT-nodes to
using the standard number of GPIOs property.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
has_irq member of struct dwapb_port_property is used only in one place,
so, make it local test instead and remove from the structure.
This local test is using memchr_inv() which is quite efficient in comparison
to the original loop and possible little overhead can be neglected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
IRQ 0 is not valid in Linux interrupt number space.
Refactor the code with this kept in mind.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_irq() will generate an error message if the requested IRQ
is not present. Use platform_get_irq_optional() to avoid the error message
being generated.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missed acpi_gpiochip_free_interrupts() call when unregistering ports.
While at it, drop extra check to call acpi_gpiochip_request_interrupts().
There is no need to have an additional check to call
acpi_gpiochip_request_interrupts(). Even without any interrupts available
the registered ACPI Event handlers can be useful for debugging purposes.
Fixes: e6cb3486f5 ("gpio: dwapb: add gpio-signaled acpi event support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some cases indentation makes code harder to read. Amend indentation
in those cases despite of lines go a bit over 80 character limit.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Cc: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200422110654.23442-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we mask interrupts before sleep, there is no need to have a conjunction
with 0xffffffff since the accepted by dwapb_write() value is 32-bit.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Cc: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200422110654.23442-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we always have a table of IDs compiled in, there is no use
for of_match_ptr() nor ACPI_PTR() call. Besides that it brings
a warning (depending on configuration):
.../gpio-dwapb.c:638:34: warning: ‘dwapb_of_match’ defined but not used [-Wunused-const-variable=]
638 | static const struct of_device_id dwapb_of_match[] = {
| ^~~~~~~~~~~~~~
Get rid of them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200415141534.31240-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no case when no context is provided in the ->suspend() and
->resume() hooks. Moreover, BUG_ON() is harmful to user and makes kernel
inoperable after the crash. Drop the BUG_ON()s for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200415141534.31240-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
More usual pattern is to prepare value and then write it in a single place.
Switch code in dwapb_gpio_set_debounce() to it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200415141534.31240-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device_get_match_data() here to simplify the code a bit.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200415141534.31240-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert to use irqd_to_hwirq() instead of direct access to the hwirq member.
Also amend the type of the hwirq holding variable to be irq_hw_number_t.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200415141534.31240-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO library provides default IRQ resource management hooks,
there is no need to repeat this in the individual driver.
Remove them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200415141534.31240-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We switch the default handler to be handle_bad_irq() instead of
handle_level_irq(), though for now apply it later in the code,
to make the difference between IRQ chips more visible.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200415141534.31240-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Refactor IRQ handler in order to enter and exit chained IRQ by using
respective prologue and epilogue calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200415141534.31240-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 3d2613c428
("GPIO: gpio-dwapb: Enable platform driver binding to MFD driver")
introduced a use of the platform driver but missed to add the following line
to it:
MODULE_ALIAS("platform:gpio-dwapb");
Add this to get driver loaded automatically if platform device is registered.
Fixes: 3d2613c428 ("GPIO: gpio-dwapb: Enable platform driver binding to MFD driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200415141534.31240-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Aside from the APB reference clock DW GPIO controller can have a
dedicated clock connected to setup a debounce time interval for
GPIO-based IRQs. Since this functionality is optional the corresponding
clock source is also optional. Due to this lets handle the debounce
clock in the same way as it has been developed for the APB reference
clock, but using the bulk request/enable-disable methods.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200323195401.30338-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The common clocks kernel framework provides a generic way to use
an optional reference clock sources. If it's utilized there is no
need in checking whether the clock descriptor pointer is actually a
negative error at the moment of the prepare/unprepare clocks method
calling. So if the corresponding clock source is provided, then
getting an error shall actually terminate the device probe procedure.
If it isn't specified then the driver shall proceed with further
initializations.
We'll use the optional clocks getting method to handle the APB reference
clock, which can be provided for instance in the device of-node with
"bus" clock-name.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200323195401.30338-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a follow up to the commit
f626d6dfb7 ("gpio: of: Break out OF-only code")
which broke down OF parts of GPIO library. Here we do the similar to ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190730104337.21235-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If dwapb_gpio_add_port() fails in dwapb_gpio_probe(),
gpio->clk is left undisabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.
No functional change intended.
Cc: Hoan Tran <hotran@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Treat DT and ACPI the same as much as possible. Note that we can't use
platform_get_irq() to get the DT interrupts as they are in the port
sub-node and hence do not have an associated platform device.
This also fixes a problem introduced with error checking when calling
platform_get_irq().
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DesignWare GPIO IP can be configured for either 1 interrupt or 1
per GPIO in port A, but the driver currently only supports 1 interrupt.
See the DesignWare DW_apb_gpio Databook description of the
'GPIO_INTR_IO' parameter.
This change allows the driver to work with up to 32 interrupts, it will
get as many interrupts as specified in the DT 'interrupts' property.
It doesn't do anything clever with the different interrupts, it just calls
the same handler used for single interrupt hardware.
ACPI companion code provided by Hoan Tran <hotran@apm.com>. This was tested
on X-Gene by Hoan.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable an optional bus clock provided by DT.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We were going out through the (legacy) gpio API to read the value
of a line to set up polarity inversion. This is abusive. Do something
less abusive by looking up the actual struct gpio_chip *
instance and calling .get() directly on it.
Acked-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This terminology is more precise. Also cut the stride calculation
in the preprocessor, it confuses more than it helps when reading
the driver.
Acked-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DW APB GPIO driver uses the generic GPIO library gpio-mmio,
and initialize the flags as "false", which should be 0.
When no flags are given, the native endianness is used to access
the MMIO registers, and the pin2mask() call can simply be
converted to a BIT() call, as per the default pin2mask()
implementation in gpio-mmio.c.
Acked-by: Alan Tull <atull@kernel.org>
Acked-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some platforms require reset to be released to allow register
access.
Signed-off-by: Alan Tull <atull@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
[Added DT bindings oneliner for standard reset binding]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch supports irq_set_wake for dwapb gpio. It allows GPIOs
to be configured as wakeup sources and wake the system from suspend.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dwapb_irq_set_type overwrites polarity register value for
IRQ_TYPE_EDGE_BOTH case. If the polarity of one gpio is 0
by default, then it will set falling edge irq trigger.
and the gpio may requires rising edge irq for the first time,
and it will be missed.
Do not overwrite polarity register for IRQ_TYPE_EDGE_BOTH case
can solve this issue.
Signed-off-by: Xiaoguang Chen <xgchenshy@gmail.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
[Fix some really weird text encoding problem]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds