Going over the virtio mmio code, I noticed that it doesn't correctly
access modern device config values using "natural" accessors: it uses
readb to get/set them byte by byte, while the virtio 1.0 spec explicitly states:
4.2.2.2 Driver Requirements: MMIO Device Register Layout
...
The driver MUST only use 32 bit wide and aligned reads and writes to
access the control registers described in table 4.1.
For the device-specific configuration space, the driver MUST use
8 bit wide accesses for 8 bit wide fields, 16 bit wide and aligned
accesses for 16 bit wide fields and 32 bit wide and aligned accesses for
32 and 64 bit wide fields.
Borrow code from virtio_pci_modern to do this correctly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio_mmio currently lacks generation support which
makes multi-byte field access racy.
Fix by getting the value at offset 0xfc for version 2
devices. Nothing we can do for version 1, so return
generation id 0.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio balloon has this code:
wait_event_interruptible(vb->config_change,
(diff = towards_target(vb)) != 0
|| vb->need_stats_update
|| kthread_should_stop()
|| freezing(current));
Which is a problem because towards_target() call might block after
wait_event_interruptible sets task state to TAST_INTERRUPTIBLE, causing
the task_struct::state collision typical of nesting of sleeping
primitives
See also http://lwn.net/Articles/628628/ or Thomas's
bug report
http://article.gmane.org/gmane.linux.kernel.virtualization/24846
for a fuller explanation.
To fix, rewrite using wait_woken.
Cc: stable@vger.kernel.org
Reported-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires that all drivers set DRIVER_OK
before using devices. While balloon isn't yet
included in the virtio 1 spec, previous spec versions
also required this.
virtio balloon might violate this rule: probe calls
kthread_run before setting DRIVER_OK, which might run
immediately and cause balloon to inflate/deflate.
To fix, call virtio_device_ready before running the kthread.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Since PCI is little endian, 8-bit access might work, but the spec section
is very clear on this:
4.1.3.1 Driver Requirements: PCI Device Layout
The driver MUST access each field using the “natural” access method,
i.e. 32-bit accesses for 32-bit fields, 16-bit accesses for 16-bit
fields and 8-bit accesses for 8-bit fields.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
The virtqueue_add() calls START_USE() upon entry. The virtqueue_kick() is
called if vq->num_added == (1 << 16) - 1 before calling END_USE().
The virtqueue_kick_prepare() called via virtqueue_kick() calls START_USE()
upon entry, and will call panic() if DEBUG is enabled.
Move this virtqueue_kick() call to after END_USE() call.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch add a support for second version of the virtio-mmio device,
which follows OASIS "Virtual I/O Device (VIRTIO) Version 1.0"
specification.
Main changes:
1. The control register symbolic names use the new device/driver
nomenclature rather than the old guest/host one.
2. The driver detect the device version (version 1 is the pre-OASIS
spec, version 2 is compatible with fist revision of the OASIS spec)
and drives the device accordingly.
3. New version uses direct addressing (64 bit address split into two
low/high register) instead of the guest page size based one,
and addresses each part of the queue (descriptors, available, used)
separately.
4. The device activity is now explicitly triggered by writing to the
"queue ready" register.
5. Whole 64 bit features are properly handled now (both ways).
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
release function in modern driver is unused:
it's a left-over from when each driver had
to have its own release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If set, try legacy interface first, modern one if that fails. Useful to
work around device/driver bugs, and for compatibility testing.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Useful for testing device virtio 1 compatibility.
Based on patch by Rusty - couldn't resist putting
that flying car joke in there!
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The ABI *is* stable, and has been for a while now.
Drop Kconfig warning saying that it's not guaranteed
to work.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Most of our code has
struct foo {
}
Fix one instances where ring is inconsistent.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Most of our code has
struct foo {
}
Fix two instances where balloon is inconsistent.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Virtio 1.0 spec lists device config as optional.
Set get/set callbacks to NULL. Drivers can check that
and fail gracefully.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We don't know the # of VQs that drivers are going to use so it's hard to
predict how much memory we'll need to map. However, the relevant
capability does give us an upper limit.
If that's below a page, we can reduce the number of required
mappings by mapping it all once ahead of the time.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Lightly tested against qemu.
One thing *not* implemented here is separate mappings
for descriptor/avail/used rings. That's nice to have,
will be done later after we have core support.
This also exposes the PCI layout to userspace, and
adds macros for PCI layout offsets:
QEMU wants it, so why not? Trust, but verify.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Most of initialization is device-independent.
Let's move it to common.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Device VQs were getting freed twice: once in every device's removal
functions, and then again in virtio_pci_legacy_remove(). The ones in
devices are called first, so drop the useless second call.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Some devices might not implement config space access
(e.g. remoteproc used not to - before 3.9).
virtio/balloon needs config space access so make it
fail gracefully if not there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The reason we defer kfree until release function is because it's a
general rule for kobjects: kfree of the reference counter itself is only
legal in the release function.
Previous patch didn't make this clear, document this in code.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A struct device which has just been unregistered can live on past the
point at which a driver decides to drop it's initial reference to the
kobject gained on allocation.
This implies that when releasing a virtio device, we can't free a struct
virtio_device until the underlying struct device has been released,
which might not happen immediately on device_unregister().
Unfortunately, this is exactly what virtio pci does:
it has an empty release callback, and frees memory immediately
after unregistering the device.
This causes an easy to reproduce crash if CONFIG_DEBUG_KOBJECT_RELEASE
it enabled.
To fix, free the memory only once we know the device is gone in the release
callback.
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It turns out we need to add device-specific code
in release callback. Move it to virtio_pci_legacy.c.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Most importantly, this fixes using virtio_pci as a module.
Further, the big virtio 1.0 conversion missed a couple of places. This fixes
them up.
This isn't 100% sparse-clean yet because on many architectures get_user
triggers sparse warnings when used with __bitwise tag (when same tag is on both
pointer and value read).
I posted a patchset to fix it up by adding __force on all
arches that don't already have it (many do), when that's
merged these warnings will go away.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUkSztAAoJECgfDbjSjVRp5DkH/ibw+0ZaEFP/SXWnw6WONpaG
pzMsrfMG/vxlOfutSUdDqG+oqqU2fSLvFq5qDK6Xk9/emRSwGduz29ZaxGh8J1MZ
/Ojqtu/HSLl+UASTs+fMw49itghoIjmAPBwwMkQjvanfqLclgdz9UxzoCOc4YkO0
PJQA/Vw6blVSP1m0p97PvzZkAiIetI2ixZn2vPJZc8vSkOHtygM9HdXKTv785HbG
ycRbR9B3OBMvq26FIuWeyuY93FnyX2Qtf2bzwSSRdzo7qlsNhVVG7sKyWOOR+1xG
TLmjhyTF57oA2GgZCVfgnFxsfiuIKMumfG0jbABTXmBGgA/ULef7HcF/lzLgdq8=
=32cU
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael S Tsirkin:
"virtio 1.0 related fixes
Most importantly, this fixes using virtio_pci as a module.
Further, the big virtio 1.0 conversion missed a couple of places.
This fixes them up.
This isn't 100% sparse-clean yet because on many architectures
get_user triggers sparse warnings when used with __bitwise tag (when
same tag is on both pointer and value read).
I posted a patchset to fix it up by adding __force on all arches that
don't already have it (many do), when that's merged these warnings
will go away"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: restore module attributes
mic/host: fix up virtio 1.0 APIs
vringh: update for virtio 1.0 APIs
vringh: 64 bit features
tools/virtio: add virtio 1.0 in vringh_test
tools/virtio: add virtio 1.0 in virtio_test
tools/virtio: enable -Werror
tools/virtio: 64 bit features
tools/virtio: fix vringh test
tools/virtio: more stubs
virtio: core support for config generation
virtio_pci: add VIRTIO_PCI_NO_LEGACY
virtio_pci: move probe to common file
virtio_pci_common.h: drop VIRTIO_PCI_NO_LEGACY
virtio_config: fix virtio_cread_bytes
virtio: set VIRTIO_CONFIG_S_FEATURES_OK on restore
bug which doesn't merit cc: stable.
All the exciting stuff went via MST this cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=COY0
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"A balloon enhancement, and a minor race-on-module-unload theoretical
bug which doesn't merit cc: stable.
All the exciting stuff went via MST this cycle"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_balloon: free some memory from balloon on OOM
virtio_balloon: return the amount of freed memory from leak_balloon()
virtio_blk: fix race at module removal
virtio: Fix comment typo 'CONFIG_S_FAILED'
When the virtio_pci driver was moved into virtio_pci_legacy.c the module
licence and other attributes went AWOL. This patch restores them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
virtio 1.0 devices require that drivers set VIRTIO_CONFIG_S_FEATURES_OK
after finalizing features.
virtio core missed doing this on restore, fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
kbuild does not seem to like it when we name source
files same as the module.
Let's rename virtio_pci -> virtio_pci_common,
and get rid of #include-ing c files.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move everything dealing with legacy devices out to virtio_pci_legacy.c.
Expose common code APIs in virtio_pci.h
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VQ setup is mostly version-specific, add another level of indirection to
split the version-independent code out.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VQ deletion is mostly version-specific, add another level of indirection
to split the version-independent code out.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
slightly reduce the amount of pointer chasing this needs to do.
More importantly, this will easily generalize to virtio 1.0.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We don't need to go from vq to vq info on
data path, so using direct vq->priv pointer for that
seems like a waste.
Let's build an array of vq infos, then we can use vq->index
for that lookup.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
legacy_only flag is now unused, drop it from core.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
we have blacklisted balloon in core, no need
for a driver flag.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
transports need to be able to detect legacy-only
devices (ATM balloon only) to use legacy path
to drive them.
Add a core API to do just that.
The implementation just blacklists balloon:
not too pretty, but let's not over-engineer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We have no plans to support virtio 1.0 in balloon driver. Add an
explicit flag to mark it legacy only.
This will be used by follow-up patches.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio-blk has some legacy feature bits that modern drivers
must not negotiate, but are needed for old legacy hosts
(that e.g. don't support virtio-scsi).
Allow a separate legacy feature table for such cases.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Now that we use u64 for bits, we can simply & them together.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
For virtio-1, we can theoretically have a more complex virtqueue
layout with avail and used buffers not on a contiguous memory area
with the descriptor table. For now, it's fine for a transport driver
to stay with the old layout: It needs, however, a way to access
the locations of the avail/used rings so it can register them with
the host.
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use virtioXX_to_cpu and friends for access to
all multibyte structures in memory.
Note: this is intentionally mechanical.
A follow-up patch will split long lines etc.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
At this point, no transports set any of the high 32 feature bits.
Since transports generally can't (yet) cope with such bits, add BUG_ON
checks to make sure they are not set by mistake.
Based on rproc patch by Rusty.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Change u32 to u64, and use BIT_ULL and 1ULL everywhere.
Note: transports are unchanged, and only set low 32 bit.
This guarantees that no transport sets e.g. VERSION_1
by mistake without proper support.
Based on patch by Rusty.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
It seemed like a good idea to use bitmap for features
in struct virtio_device, but it's actually a pain,
and seems to become even more painful when we get more
than 32 feature bits. Just change it to a u32 for now.
Based on patch by Rusty.
Suggested-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Excessive virtio_balloon inflation can cause invocation of OOM-killer,
when Linux is under severe memory pressure. Various mechanisms are
responsible for correct virtio_balloon memory management. Nevertheless
it is often the case that these control tools does not have enough time
to react on fast changing memory load. As a result OS runs out of memory
and invokes OOM-killer. The balancing of memory by use of the virtio
balloon should not cause the termination of processes while there are
pages in the balloon. Now there is no way for virtio balloon driver to
free some memory at the last moment before some process will be get
killed by OOM-killer.
This does not provide a security breach as balloon itself is running
inside guest OS and is working in the cooperation with the host. Thus
some improvements from guest side should be considered as normal.
To solve the problem, introduce a virtio_balloon callback which is
expected to be called from the oom notifier call chain in out_of_memory()
function. If virtio balloon could release some memory, it will make
the system to return and retry the allocation that forced the out of
memory killer to run.
Allocate virtio feature bit for this: it is not set by default,
the the guest will not deflate virtio balloon on OOM without explicit
permission from host.
Signed-off-by: Raushaniya Maksudova <rmaksudova@parallels.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This value would be useful in the next patch to provide the amount of
the freed memory for OOM killer.
Signed-off-by: Raushaniya Maksudova <rmaksudova@parallels.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
been sitting in MST's tree during my vacation. I changed a function name
and made one trivial change, then they spent two days in linux-next.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JK6x
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"One cc: stable commit, the rest are a series of minor cleanups which
have been sitting in MST's tree during my vacation. I changed a
function name and made one trivial change, then they spent two days in
linux-next"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
virtio-rng: refactor probe error handling
virtio_scsi: drop scan callback
virtio_balloon: enable VQs early on restore
virtio_scsi: fix race on device removal
virito_scsi: use freezable WQ for events
virtio_net: enable VQs early on restore
virtio_console: enable VQs early on restore
virtio_scsi: enable VQs early on restore
virtio_blk: enable VQs early on restore
virtio_scsi: move kick event out from virtscsi_init
virtio_net: fix use after free on allocation failure
9p/trans_virtio: enable VQs early
virtio_console: enable VQs early
virtio_blk: enable VQs early
virtio_net: enable VQs early
virtio: add API to enable VQs early
virtio_net: minor cleanup
virtio-net: drop config_mutex
virtio_net: drop config_enable
virtio-blk: drop config_mutex
...
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after resume returns, virtio balloon
violated this rule by adding bufs, which causes the VQ to be used
directly within restore.
To fix, call virtio_device_ready before using VQ.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Defer config changed notifications that arrive during
probe/scan/freeze/restore.
This will allow drivers to set DRIVER_OK earlier, without worrying about
racing with config change interrupts.
This change will also benefit old hypervisors (before 2009)
that send interrupts without checking DRIVER_OK: previously,
the callback could race with driver-specific initialization.
This will also help simplify drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (cosmetic changes)
This is in preparation to extending config changed event handling
in core.
Wrapping these in an API also seems to make for a cleaner code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Replace duplicated code in all transports with a single wrapper in
virtio.c.
The only functional change is in virtio_mmio.c: if a buggy device sends
us an interrupt before driver is set, we previously returned IRQ_NONE,
now we return IRQ_HANDLED.
As this must not happen in practice, this does not look like a big deal.
See also commit 3fff0179e3
virtio-pci: do not oops on config change if driver not loaded.
for the original motivation behind the driver check.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
On restore, virtio pci does the following:
+ set features
+ init vqs etc - device can be used at this point!
+ set ACKNOWLEDGE,DRIVER and DRIVER_OK status bits
This is in violation of the virtio spec, which
requires the following order:
- ACKNOWLEDGE
- DRIVER
- init vqs
- DRIVER_OK
This behaviour will break with hypervisors that assume spec compliant
behaviour. It seems like a good idea to have this patch applied to
stable branches to reduce the support butden for the hypervisors.
Cc: stable@vger.kernel.org
Cc: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Always mark pages with PageBalloon even if balloon compaction is disabled
and expose this mark in /proc/kpageflags as KPF_BALLOON.
Also this patch adds three counters into /proc/vmstat: "balloon_inflate",
"balloon_deflate" and "balloon_migrate". They accumulate balloon
activity. Current size of balloon is (balloon_inflate - balloon_deflate)
pages.
All generic balloon code now gathered under option CONFIG_MEMORY_BALLOON.
It should be selected by ballooning driver which wants use this feature.
Currently virtio-balloon is the only user.
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now ballooned pages are detected using PageBalloon(). Fake mapping is no
longer required. This patch links ballooned pages to balloon device using
field page->private instead of page->mapping. Also this patch embeds
balloon_dev_info directly into struct virtio_balloon.
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sasha Levin reported KASAN splash inside isolate_migratepages_range().
Problem is in the function __is_movable_balloon_page() which tests
AS_BALLOON_MAP in page->mapping->flags. This function has no protection
against anonymous pages. As result it tried to check address space flags
inside struct anon_vma.
Further investigation shows more problems in current implementation:
* Special branch in __unmap_and_move() never works:
balloon_page_movable() checks page flags and page_count. In
__unmap_and_move() page is locked, reference counter is elevated, thus
balloon_page_movable() always fails. As a result execution goes to the
normal migration path. virtballoon_migratepage() returns
MIGRATEPAGE_BALLOON_SUCCESS instead of MIGRATEPAGE_SUCCESS,
move_to_new_page() thinks this is an error code and assigns
newpage->mapping to NULL. Newly migrated page lose connectivity with
balloon an all ability for further migration.
* lru_lock erroneously required in isolate_migratepages_range() for
isolation ballooned page. This function releases lru_lock periodically,
this makes migration mostly impossible for some pages.
* balloon_page_dequeue have a tight race with balloon_page_isolate:
balloon_page_isolate could be executed in parallel with dequeue between
picking page from list and locking page_lock. Race is rare because they
use trylock_page() for locking.
This patch fixes all of them.
Instead of fake mapping with special flag this patch uses special state of
page->_mapcount: PAGE_BALLOON_MAPCOUNT_VALUE = -256. Buddy allocator uses
PAGE_BUDDY_MAPCOUNT_VALUE = -128 for similar purpose. Storing mark
directly in struct page makes everything safer and easier.
PagePrivate is used to mark pages present in page list (i.e. not
isolated, like PageLRU for normal pages). It replaces special rules for
reference counter and makes balloon migration similar to migration of
normal pages. This flag is protected by page_lock together with link to
the balloon device.
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Link: http://lkml.kernel.org/p/53E6CEAA.9020105@oracle.com
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: <stable@vger.kernel.org> [3.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
virtqueue_add() populates the virtqueue descriptor table from the sgs
given. If it uses an indirect descriptor table, then it puts a single
descriptor in the descriptor table pointing to the kmalloc'ed indirect
table where the sg is populated.
Previously vring_add_indirect() did the allocation and the simple
linear layout. We replace that with alloc_indirect() which allocates
the indirect table then chains it like the normal descriptor table so
we can reuse the core logic.
This slows down pktgen by less than 1/2 a percent (which uses direct
descriptors), as well as vring_bench, but it's far neater.
vring_bench before:
1061485790-1104800648(1.08254e+09+/-6.6e+06)ns
vring_bench after:
1125610268-1183528965(1.14172e+09+/-8e+06)ns
pktgen before:
787781-796334(793165+/-2.4e+03)pps 365-369(367.5+/-1.2)Mb/sec (365530384-369498976(3.68028e+08+/-1.1e+06)bps) errors: 0
pktgen after:
779988-790404(786391+/-2.5e+03)pps 361-366(364.35+/-1.3)Mb/sec (361914432-366747456(3.64885e+08+/-1.2e+06)bps) errors: 0
Now, if we make force indirect descriptors by turning off any_header_sg
in virtio_net.c:
pktgen before:
713773-721062(718374+/-2.1e+03)pps 331-334(332.95+/-0.92)Mb/sec (331190672-334572768(3.33325e+08+/-9.6e+05)bps) errors: 0
pktgen after:
710542-719195(714898+/-2.4e+03)pps 329-333(331.15+/-1.1)Mb/sec (329691488-333706480(3.31713e+08+/-1.1e+06)bps) errors: 0
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to have several callers which just used arrays. They're
gone, so we can use sg_next() everywhere, simplifying the code.
On my laptop, this slowed down vring_bench by 15%:
vring_bench before:
936153354-967745359(9.44739e+08+/-6.1e+06)ns
vring_bench after:
1061485790-1104800648(1.08254e+09+/-6.6e+06)ns
However, a more realistic test using pktgen on a AMD FX(tm)-8320 saw
a few percent improvement:
pktgen before:
767390-792966(785159+/-6.5e+03)pps 356-367(363.75+/-2.9)Mb/sec (356068960-367936224(3.64314e+08+/-3e+06)bps) errors: 0
pktgen after:
787781-796334(793165+/-2.4e+03)pps 365-369(367.5+/-1.2)Mb/sec (365530384-369498976(3.68028e+08+/-1.1e+06)bps) errors: 0
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to meet
kernel coding style guidelines. This issue was reported by checkpatch.
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Heinz points out that adding buffers to a broken virtqueue (which
should "never happen") still works. Failing allows drivers to detect
and complain about broken devices.
Now drivers are robust, we can add this extra check.
Reported-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A bad implementation of virtio might cause us to mark the virtqueue
broken: we'll dev_err() in that case, and the device is useless, but
let's not BUG().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When adding or removing 100G from a balloon:
BUG: soft lockup - CPU#0 stuck for 22s! [vballoon:367]
We have a wait_event_interruptible(), but the condition is always true
(more ballooning to do) so we don't ever sleep. We also have a
wait_event() for the host to ack, but that is also always true as QEMU
is synchronous for balloon operations.
Reported-by: Gopesh Kumar Chaudhary <gopchaud@in.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In commit bb478d8b16 virtio_ring: plug kmemleak false positive,
kmemleak_ignore was introduced. This broke compilation of virtio_test:
cc -g -O2 -Wall -I. -I ../../usr/include/ -Wno-pointer-sign
-fno-strict-overflow -fno-strict-aliasing -fno-common -MMD
-U_FORTIFY_SOURCE -c -o virtio_ring.o ../../drivers/virtio/virtio_ring.c
../../drivers/virtio/virtio_ring.c: In function ‘vring_add_indirect’:
../../drivers/virtio/virtio_ring.c:177:2: warning: implicit declaration
of function ‘kmemleak_ignore’ [-Wimplicit-function-declaration]
kmemleak_ignore(desc);
^
cc virtio_test.o virtio_ring.o -o virtio_test
virtio_ring.o: In function `vring_add_indirect':
tools/virtio/../../drivers/virtio/virtio_ring.c:177:
undefined reference to `kmemleak_ignore'
Add a dummy header for tools/virtio, and add #incldue <linux/kmemleak.h>
to drivers/virtio/virtio_ring.c so it is picked up by the userspace
tools.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Mark the function virtballoon_migratepage() as static in
virtio_balloon.c because it is not used outside this file.
This eliminates the following warning in virtio_balloon.c:
drivers/virtio/virtio_balloon.c:372:5: warning: no previous prototype for ‘virtballoon_migratepage’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
According to the virtio spec, the device configuration field
that should be updated after an inflation or deflation
operation is the 'actual' field, not the 'num_pages' one.
Commit 855e0c5288 swapped them
in update_balloon_size(). Fix it.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fixes: 855e0c5288
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
some robustness fixes for broken virtio devices, plus minor tweaks.
[vs last pull request: added the virtio-scsi broken vq escape patch, which
I somehow lost.]
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=vY2L
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing really exciting: some groundwork for changing virtio endian,
and some robustness fixes for broken virtio devices, plus minor
tweaks"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: verify if queue is broken after virtqueue_get_buf()
x86, asmlinkage, lguest: Pass in globals into assembler statement
virtio: mmio: fix signature checking for BE guests
virtio_ring: adapt to notify() returning bool
virtio_net: verify if queue is broken after virtqueue_get_buf()
virtio_console: verify if queue is broken after virtqueue_get_buf()
virtio_blk: verify if queue is broken after virtqueue_get_buf()
virtio_ring: add new function virtqueue_is_broken()
virtio_test: verify if virtqueue_kick() succeeded
virtio_net: verify if virtqueue_kick() succeeded
virtio_ring: let virtqueue_{kick()/notify()} return a bool
virtio_ring: change host notification API
virtio_config: remove virtio_config_val
virtio: use size-based config accessors.
virtio_config: introduce size-based accessors.
virtio_ring: plug kmemleak false positive.
virtio: pm: use CONFIG_PM_SLEEP instead of CONFIG_PM
As virtio-mmio config registers are specified to be little-endian,
using readl() to read the magic value and then memcmp() to check it
fails on BE (as readl() has an implicit swab).
Fix it by encoding the magic value as an integer instead of a string.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Correct if statement to check for bool returned by notify()
(introduced in 5b1bf7cb67).
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add new function virtqueue_is_broken(). Callers of virtqueue_get_buf()
should check for a broken queue.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtqueue_{kick()/notify()} should exploit the new host notification API.
If the notify call returned with a negative value the host kick failed
(e.g. a kick triggered after a device was hot-unplugged). In this case
the virtqueue is set to 'broken' and false is returned, otherwise true.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently a host kick error is silently ignored and not reflected in
the virtqueue of a particular virtio device.
Changing the notify API for guest->host notification seems to be one
prerequisite in order to be able to handle such errors in the context
where the kick is triggered.
This patch changes the notify API. The notify function must return a
bool return value. It returns false if the host notification failed.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the virtio bus code to use the
correct field.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <virtualization@lists.linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lets the transport do endian conversion if necessary, and insulates
the drivers from the difference.
Most drivers can use the simple helpers virtio_cread() and virtio_cwrite().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The freeze and restore functions defined in virtio drivers are used
for suspend and hibernate, so CONFIG_PM_SLEEP is more appropriate than
CONFIG_PM. This patch replace all CONFIG_PM with CONFIG_PM_SLEEP for
virtio drivers that implement freeze and restore callbacks.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The virtio_pci_freeze/restore are defined under CONFIG_PM but is used
by SET_SYSTEM_SLEEP_PM_OPS macro, which is defined under
CONFIG_PM_SLEEP. So if CONFIG_PM_SLEEP is not cofigured but
CONFIG_PM_RUNTIME is, the following warning message appeared:
drivers/virtio/virtio_pci.c:770:12: warning: ‘virtio_pci_freeze’ defined but not used [-Wunused-function]
static int virtio_pci_freeze(struct device *dev)
^
drivers/virtio/virtio_pci.c:790:12: warning: ‘virtio_pci_restore’ defined but not used [-Wunused-function]
static int virtio_pci_restore(struct device *dev)
^
Fix it by changing CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
This adds a way to check ring empty state after enable_cb outside any
locks. Will be used by virtio_net.
Note: there's room for more optimization: caller is likely to have a
memory barrier already, which means we might be able to get rid of a
barrier here. Deferring this optimization until we do some
benchmarking.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
Enhance adjust_managed_page_count() to adjust totalhigh_pages for
highmem pages. And change code which directly adjusts totalram_pages to
use adjust_managed_page_count() because it adjusts totalram_pages,
totalhigh_pages and zone->managed_pages altogether in a safe way.
Remove inc_totalhigh_pages() and dec_totalhigh_pages() from xen/balloon
driver bacause adjust_managed_page_count() has already adjusted
totalhigh_pages.
This patch also fixes two bugs:
1) enhances virtio_balloon driver to adjust totalhigh_pages when
reserve/unreserve pages.
2) enhance memory_hotplug.c to adjust totalhigh_pages when hot-removing
memory.
We still need to deal with modifications of totalram_pages in file
arch/powerpc/platforms/pseries/cmm.c, but need help from PPC experts.
[akpm@linux-foundation.org: remove ifdef, per Wanpeng Li, virtio_balloon.c cleanup, per Sergei]
[akpm@linux-foundation.org: export adjust_managed_page_count() to modules, for drivers/virtio/virtio_balloon.c]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Minchan Kim <minchan@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
balloon_page_dequeue() can return NULL. If it does for the first page
being freed then leak_balloon() will create a scatter list with len=0.
Which in turn seems to generate an invalid virtio request.
I didn't get this in practice, I found it by code review. On the other
hand, such an invalid virtio request will cause errors in QEMU and
fill_balloon() also performs the same check implemented by this commit.
This bug was introduced in e2250429.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Acked-by: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # 3.9
Michael S. Tsirkin