Add compatible string to use this generic glue layer to support
Intel Keem Bay platform's dwc3 controller.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC3 IPs can use the maximum stream id (up to 2^16) specified by the
USB 3.x specs. Don't limit to stream id 2^15 only. Note that this does
not reflect the number of concurrent streams the controller handles
internally.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the transfer had already started and there's no TRB to update, then
there's no need to go through __dwc3_gadget_kick_transfer(). There is
no problem reissuing UPDATE_TRANSFER command. This change just saves
the driver from doing a few operations. This happens when we run out of
TRB and function driver still queues for more requests.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If we couldn't finish preparing all the TRBs of a request, don't prepare
the next request. Otherwise, the TRBs order will be mixed up and the
controller will process the wrong TRB. This is a corner case where
there's not enough TRBs for a request that needs the extra TRB but
there's still 1 available TRB in the pool.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To keep the setting of interrupt-on-completion (IOC) when out of TRBs
consistent and easier to read, the caller of dwc3_prepare_one_trb()
will determine if the TRB must have IOC bit set. This also reduces the
number of times we need to call dwc3_calc_trbs_left(). Note that we only
care about setting IOC from insufficient number of TRBs for SG and not
linear requests (because we don't need to split linear requests).
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Previously if we run out of TRBs for the last SG entry that requires
an extra TRB, we set interrupt-on-completion (IOC) bit to an already
prepared TRB (i.e. HWO=1). This logic is not clean, and it's not a
typical way to prepare TRB. Also, this prevents showing IOC setup in
tracepoint when __dwc3_prepare_one_trb() is executed. Instead, let's
look ahead when preparing TRB to know whether to set the IOC bit before
the last SG entry. This requires adding a new parameter "must_interrupt"
to dwc3_prepare_one_trb().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It's possible that there's no new TRBs prepared when kicking a transfer.
This happens when we need to stop and restart a transfer such as in the
case of reinitiating a stream or retrying isoc transfer. For streams,
sometime host may reject a stream and the device may need to reinitiate
that stream by stopping and restarting a transfer. In this case, all the
TRBs may have already been prepared. Allow the function
__dwc3_gadget_kick_transfer() to go through even though there's no new
TRB.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In the DWC3 databook, for a device initiated disconnect or bus reset, the
driver is required to send dependxfer commands for any pending transfers.
In addition, before the controller can move to the halted state, the SW
needs to acknowledge any pending events. If the controller is not halted
properly, there is a chance the controller will continue accessing stale or
freed TRBs and buffers.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
SPLIT_BOUNDARY_DISABLE should be set for DesignWare USB3 DRD Core
of Hisilicon Kirin Soc when dwc3 core act as host.
[mchehab: dropped a dev_dbg() as only traces are now allowwed on this driver]
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The functions dwc3_prepare_one_trb_sg and dwc3_prepare_one_trb_linear
are not necessarily preparing "one" TRB, it can prepare multiple TRBs.
Rename these functions as follow:
dwc3_prepare_one_trb_sg -> dwc3_prepare_trbs_sg
dwc3_prepare_one_trb_linear -> dwc3_prepare_trbs_linear
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There are a lot of common codes for preparing SG and linear TRBs.
Refactor them for easier read.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If we run out of TRBs because we need extra TRBs, make sure to set the
IOC bit for the previously prepared TRB to get completion notification
to free up TRBs to resume later.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
By returning the number of TRBs prepared, we know whether to execute
__dwc3_gadget_kick_transfer(). This allows us to check if we ran out of
TRBs when extra TRBs are needed for OUT transfers. It also allows us to
properly handle usb_gadget_map_request_by_dev() error.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In preparation for fixing the check for number of remaining TRBs,
revise dwc3_prepare_one_trb_linear() and dwc3_prepare_one_trb_sg() to
return the number of prepared TRBs.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current ZLP handling for ep0 requests is only for control IN
requests. For OUT direction, DWC3 needs to check and setup for MPS
alignment.
Usually, control OUT requests can indicate its transfer size via the
wLength field of the control message. So usb_request->zero is usually
not needed for OUT direction. To handle ZLP OUT for control endpoint,
make sure the TRB is MPS size.
Cc: stable@vger.kernel.org
Fixes: c7fcdeb262 ("usb: dwc3: ep0: simplify EP0 state machine")
Fixes: d6e5a549cc ("usb: dwc3: simplify ZLP handling")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
For OUT requests that requires extra TRBs for ZLP. We don't need to
prepare the 0-length TRB and simply prepare the MPS size TRB. This
reduces 1 TRB needed to prepare for ZLP.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When the driver prepares the extra TRB, it uses bounce buffer. If we
just add a new parameter to dwc3_prepare_one_trb() to indicate this,
then we can refactor and simplify the driver quite a bit.
dwc3_prepare_one_trb() also checks if a request had been moved to the
started list. This is a prerequisite to subsequence patches improving
the handling of extra TRBs.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
An SG request may be partially completed (due to no available TRBs).
Don't reclaim extra TRBs and clear the needs_extra_trb flag until the
request is fully completed. Otherwise, the driver will reclaim the wrong
TRB.
Cc: stable@vger.kernel.org
Fixes: 1f512119a0 ("usb: dwc3: gadget: add remaining sg entries to ring")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When preparing for SG, not all the entries are prepared at once. When
resume, don't use the remaining request length to calculate for MPS
alignment. Use the entire request->length to do that.
Cc: stable@vger.kernel.org
Fixes: 5d187c0454 ("usb: dwc3: gadget: Don't setup more than requested")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Refactor END_TRANSFER command completion handling and move it outside of
the switch statement to its own function. This makes it cleaner and
consistent with other event handler functions. No functional change
here.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add the phy cleanup if dwc3 mode init fail, which is the missing part of
de-init for dwc3 core init.
Fixes: c499ff71ff ("usb: dwc3: core: re-factor init and exit paths")
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current code uses commit fac323471d ("usb: udc: allow adding
and removing the same gadget device") as the workaround to let
the gadget device is re-used, but it is not allowed from driver
core point. In this commit, we allocate gadget structure dynamically,
and free it at its release function. Since the gadget device's
driver_data has already occupied by usb_composite_dev structure, we have
to use gadget device's platform data to store dwc3 structure.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Similar to some other IA platforms, Elkhart Lake too depends on the
PMU register write to request transition of Dx power state.
Thus, we add the PCI_DEVICE_ID_INTEL_EHLLP to the list of devices that
shall execute the ACPI _DSM method during D0/D3 sequence.
[heikki.krogerus@linux.intel.com: included Fixes tag]
Fixes: dbb0569de8 ("usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices")
Cc: stable@vger.kernel.org
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The Amlogic AXG is close to the GXL Glue but with a single OTG PHY.
It needs the same init sequence as GXL & GXM, but it seems it doesn't need
the host disconnect bit.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/dwc3/trace.c: note: in included file (through drivers/usb/dwc3/trace.h):
drivers/usb/dwc3/debug.h:374:39: warning: cast to non-scalar
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add interconnect support in dwc3-qcom driver to vote for bus
bandwidth.
This requires for two different paths - from USB to
DDR. The other is from APPS to USB.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The user may have more information to override the HW parameter to
specify the maximum_speed. However, if the user specifies a
maximum_speed that the controller doesn't support, print out a warning.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not specified, default the device speed base on
its HW capability. Don't prematurely check HW capability before
validating the maximum_speed device property. The device property takes
precedence in dwc->maximum_speed.
Fixes: 0e1e5c47f7 ("usb: dwc3: add support for USB 2.0-only core configuration")
Reported-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According the programming guide (for all DWC3 IPs), when the driver
handles ClearFeature(halt) request, it should issue CLEAR_STALL command
_after_ the END_TRANSFER command completes. The END_TRANSFER command may
take some time to complete. So, delay the ClearFeature(halt) request
control status stage and wait for END_TRANSFER command completion
interrupt. Only after END_TRANSFER command completes that the driver
may issue CLEAR_STALL command.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The function driver may queue new requests right after halting the
endpoint (i.e. queue new requests while the endpoint is stalled).
There's no restriction preventing it from doing so. However, dwc3
currently drops those requests after CLEAR_STALL. The driver should only
drop started requests. Keep the pending requests in the pending list to
resume and process them after the host issues ClearFeature(Halt) to the
endpoint.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit 7a410953d1.
This commit breaks USB on meson-gxl-s905x-libretech-cc. Reverting
the change solves the issue.
In fact, according to the reset framework code, consumers must not use
reset_control_(de)assert() on shared reset lines when reset_control_reset
has been used, and vice-versa.
Moreover, with this commit, usb is not guaranted to be reset since the
reset is likely to be initially deasserted.
Reverting the commit will bring back the suspend warning mentioned in the
commit description. Nevertheless, a warning is much less critical than
breaking dwc3-meson-g12a USB completely. We will address the warning
issue in another way as a 2nd step.
Fixes: 7a410953d1 ("usb: dwc3: meson-g12a: fix shared reset control use")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20200827144810.26657-1-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that:
- the usb gadget patch now does not break some systems, and
actually does what it was intended to do. Many thanks to
Marek Szyprowski for quickly noticing and testing the patch
from Andy Shevchenko to resolve this issue.
- some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the original pull request patches are all here, and
they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0t32g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFMACeLEQgeN1rmfQfLyo2NHROQEeDhnIAniLMhchZ
p9dXWJ8aNeyI5OrNjD5b
=Vd05
-----END PGP SIGNATURE-----
Merge tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that
the usb gadget patch now does not break some systems, and actually
does what it was intended to do. Many thanks to Marek Szyprowski for
quickly noticing and testing the patch from Andy Shevchenko to resolve
this issue.
Additionally, some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the patches are all here, and they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues"
* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: storage: Add unusual_uas entry for Sony PSZ drives
USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
USB: gadget: u_f: Unbreak offset calculation in VLAs
USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
USB: PHY: JZ4770: Fix static checker warning.
USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
USB: gadget: u_f: add overflow checks to VLA macros
xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
xhci: Do warm-reset when both CAS and XDEV_RESUME are set
usb: host: xhci: fix ep context print mismatch in debugfs
usb: uas: Add quirk for PNY Pro Elite
tools: usb: move to tools buildsystem
USB: Fix device driver race
USB: Also match device drivers using the ->match vfunc
usb: host: xhci-tegra: fix tegra_xusb_get_phy()
usb: host: xhci-tegra: otg usb2/usb3 port init
usb: hcd: Fix use after free in usb_hcd_pci_remove()
usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
...
Currently dwc3 doesn't handle usb_request->zero for SG requests. This
change checks and prepares extra TRBs for the ZLP for SG requests.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The usb_request->zero doesn't apply for isoc. Also, if we prepare a
0-length (ZLP) TRB for the OUT direction, we need to prepare an extra
TRB to pad up to the MPS alignment. Use the same bounce buffer for the
ZLP TRB and the extra pad TRB.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: d6e5a549cc ("usb: dwc3: simplify ZLP handling")
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The SG list may be set up with entry size more than the requested
length. Check the usb_request->length and make sure that we don't setup
the TRBs to send/receive more than requested. This case may occur when
the SG entry is allocated up to a certain minimum size, but the request
length is less than that. It can also occur when the request is reused
for a different request length.
Cc: <stable@vger.kernel.org> # v4.18+
Fixes: a31e63b608 ("usb: dwc3: gadget: Correct handling of scattergather lists")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Wan Ahmad Zainie