* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9
gro: Only reset frag0 when skb can be pulled
...
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (741 commits)
staging:iio:meter:ade7753 should be 16 bit read not 8 bit for mode register.
staging:iio:kfifo_buf fix double initialization of the ring device structure.
staging:iio:accel:lis3l02dq: fix incorrect pointer passed to spi_set_drvdata.
staging:iio:imu fix missing register table index for some channels
spectra: enable device before poking it
staging: rts_pstor: Fix a miswriting
staging/lirc_bt829: Return -ENODEV when no hardware is found.
staging/lirc_parallel: remove pointless prototypes.
staging/lirc_parallel: fix panic on rmmod
staging:iio:adc:ad7476: Incorrect pointer into spi_set_drvdata.
Staging: zram: Fix kunmapping order
Revert "gma500: Fix dependencies"
gma500: Add medfield header
gma500: wire up the mrst i2c bus from chip_info
gma500: Fix DPU build
gma500: Clean up the DPU config and make it runtime
gma500: resync with Medfield progress
gma500: Use the mrst helpers and power control for mode commit
gma500@ Fix backlight range error
gma500: More Moorestown muddle meddling means MM maybe might modeset
...
Fix up fairly trivial conflicts all over, mostly due to header file
cleanup conflicts, but some deleted files and some just context changes:
- Documentation/feature-removal-schedule.txt
- drivers/staging/bcm/headers.h
- drivers/staging/brcm80211/brcmfmac/dhd_linux.c
- drivers/staging/brcm80211/brcmfmac/dhd_sdio.c
- drivers/staging/brcm80211/brcmfmac/wl_cfg80211.h
- drivers/staging/brcm80211/brcmfmac/wl_iw.c
- drivers/staging/et131x/et131x_netdev.c
- drivers/staging/rtl8187se/ieee80211/ieee80211_softmac.c
- drivers/staging/rtl8192e/r8192E.h
- drivers/staging/usbip/userspace/src/utils.h
Add new testmode command for retrieving rx reports from firmware.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement cfg80211_ops set_pmksa, del_pmksa, and flush_pmksa to enable
PMKSA caching support.
kvalo: backported from ath6kl-cleanup tree
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add testmode support for running low level hardware tests. The testmode
is enabled by setting testmode module parameter to 1.
For now only a simple command passing is supported. More advanced
support will be implemented later.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cfg80211 exports wiphy->fw_version to user space via ethtool interface.
The obligatory screenshot:
$ sudo ethtool -i wlan0
driver: ath6kl_hifdev
version: 2.6.39-rc4+
firmware-version: 3:1:1:149
bus-info: mmc0:0001:1
$
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/staging/ath6kl/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should not request firmware during resume. Fix ath6kl to
cache the firmware instead.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: stable <stable@kernel.org> [3.0]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ath6kl module was resumed while a scan was ongoing, for example during
suspend, the driver would crash in ar6k_cfg80211_scanComplete_event():
[26581.586440] Call Trace:
[26581.586440] [<f99ffeda>] ? ar6k_cfg80211_scanComplete_event+0xaa/0xaa [ath6kl]
[26581.586440] [<f9a0a020>] wmi_iterate_nodes+0xb/0xd [ath6kl]
[26581.586440] [<f99ffe78>] ar6k_cfg80211_scanComplete_event+0x48/0xaa [ath6kl]
[26581.586440] [<f9a038ae>] ar6000_close+0x77/0x7e [ath6kl]
[26581.586440] [<c139c25d>] __dev_close_many+0x87/0xab
[26581.586440] [<c139c30a>] dev_close_many+0x54/0xab
[26581.586440] [<c139c437>] rollback_registered_many+0xa5/0x19e
[26581.586440] [<c139c595>] rollback_registered+0x23/0x2f
[26581.586440] [<c139c5ed>] unregister_netdevice_queue+0x4c/0x69
[26581.586440] [<c139c6b2>] unregister_netdev+0x18/0x1f
[26581.586440] [<f9a00d4c>] ar6000_destroy+0xf8/0x115 [ath6kl]
[26581.586440] [<f9a0c765>] ar6k_cleanup_module+0x20/0x29 [ath6kl]
[26581.586440] [<c1062843>] sys_delete_module+0x181/0x1d9
[26581.586440] [<c105876b>] ? lock_release_holdtime+0x2b/0xcd
[26581.586440] [<c10b55dc>] ? sys_munmap+0x3b/0x42
[26581.586440] [<c14a99dc>] ? restore_all+0xf/0xf
[26581.586440] [<c14aeb6c>] sysenter_do_call+0x12/0x32
[26581.586440] Code: 89 53 6c 75 07 89 d8 e8 c0 ff ff ff 89 f0 e8 2c f2 a9 c7 5b 5e 5d c3 55 89 e5 57 56 53 89 c3 83 ec 08 89 55 f0 8d 78 04 89 4d ec <8b> b0 b8 00 00 00 46 89 b0 b8 00 00 00 89 f8 e8 ae ed a9 c7 8b
Fix the function not to iterate nodes when the scan is aborted. The nodes
are already freed when the module is being unloaded. Patch "ath6kl: Fix a
kernel panic furing suspend/resume" tried to fix this already but it wasn't
enough as a pointer was still used even after the null check. This patch
removes the null check entirely as the wmi structure is not accessed anymore
during module unload.
Also fix a bug where the status was checked as a bitfield with '&' operator.
But it's not a bitfield, just a regular (enum like) value.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: stable <stable@kernel.org> [3.0]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix build errors when CONFIG_CFG80211 is not enabled:
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b71): undefined reference to `cfg80211_scan_done'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b86): undefined reference to `wiphy_unregister'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b8d): undefined reference to `wiphy_free'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18add7): undefined reference to `wiphy_new'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18ae48): undefined reference to `wiphy_register'
drivers/built-in.o: In function `ar6k_cfg80211_tkip_micerr_event':
(.text+0x18ae95): undefined reference to `cfg80211_michael_mic_failure'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afb5): undefined reference to `__ieee80211_get_channel'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afd2): undefined reference to `cfg80211_inform_bss_frame'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b046): undefined reference to `cfg80211_ibss_joined'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b176): undefined reference to `cfg80211_connect_result'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b190): undefined reference to `cfg80211_disconnected'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b291): undefined reference to `cfg80211_get_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b457): undefined reference to `cfg80211_put_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b4fa): undefined reference to `cfg80211_roamed'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Peter Foley <pefoley2@verizon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (89 commits)
bonding: documentation and code cleanup for resend_igmp
bonding: prevent deadlock on slave store with alb mode (v3)
net: hold rtnl again in dump callbacks
Add Fujitsu 1000base-SX PCI ID to tg3
bnx2x: protect sequence increment with mutex
sch_sfq: fix peek() implementation
isdn: netjet - blacklist Digium TDM400P
via-velocity: don't annotate MAC registers as packed
xen: netfront: hold RTNL when updating features.
sctp: fix memory leak of the ASCONF queue when free asoc
net: make dev_disable_lro use physical device if passed a vlan dev (v2)
net: move is_vlan_dev into public header file (v2)
bug.h: Fix build with CONFIG_PRINTK disabled.
wireless: fix fatal kernel-doc error + warning in mac80211.h
wireless: fix cfg80211.h new kernel-doc warnings
iwlagn: dbg_fixed_rate only used when CONFIG_MAC80211_DEBUGFS enabled
dst: catch uninitialized metrics
be2net: hash key for rss-config cmd not set
bridge: initialize fake_rtable metrics
net: fix __dst_destroy_metrics_generic()
...
Fix up trivial conflicts in drivers/staging/brcm80211/brcmfmac/wl_cfg80211.c
cfg80211 scan code adds separate BSS entries if the same BSS shows up
on multiple channels. However, sme implementation does not use the
frequency when fetching the BSS entry. Fix this by adding channel
information to cfg80211_roamed() and include it in cfg80211_get_bss()
calls.
Please note that drivers using cfg80211_roamed() need to be modified to
fully implement this fix. This commit includes only minimal changes to
avoid compilation issues; it maintains the old (broken) behavior for
most drivers. ath6kl was the only one that I could test, so I updated
it to provide the operating frequency in the roamed event.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
implementing the cfg ops that gets called when iw dev wlan0
link is issued by user. The ops that needs to be implemented
is get_station.
kvalo: check the mac address, remove signal_pending(), use ARRAY_SIZE()
and fix style issues
Signed-off-by: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Kalle Valo <kalle.valo@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A call to cfg80211_get_bss hould be accompanied by a call to
cfg80211_put_bss in error-handling code.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression struct cfg80211_bss * x;
expression ra,rr;
position p1,p2;
@@
x = cfg80211_get_bss@p1(...)
... when != x = rr
when != cfg80211_put_bss(x,...)
when != if (...) { ... cfg80211_put_bss(x,...) ...}
if(...) { ... when != x = ra
when forall
when != cfg80211_put_bss(x,...)
\(return <+...x...+>; \| return@p2...; \) }
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
cocci.print_main("cfg80211_get_bss",p1)
cocci.print_secs("return",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After this there is no difference between hw2.0/hw/gpio_reg.h
and hw4.0/hw/gpio_reg.h, so remove the duplication.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The macros and function proto types in these files are
not used anywhere.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also delete si_reg.h which is only used in eeprom.c
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is not defined anywhere, also delete vmc_reg.h which is
used only in the dead code.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the wpa_supplicant conf file supplies both open and shared
algorithm, and AP is configured as shared then connection never
happens. Since it is a FMAC driver additional logic is added in
driver which first detects this, then tries open algorithm for the
first time and when it fails tries the shared algo.
kvalo: fix style issues
Signed-off-by: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Kalle Valo <kalle.valo@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a heavy traffic is undergoing and a link is lost (bcn miss),
wlan driver does a reconnection on its own and after connection
is re-established, reports it as ROAM_EVENT to cfg. Now this event
is handled as work queue. It could very well happen that by the
time this event gets handled, cfg would have aged out the bss and
we get the following WARN_ON in __cfg80211_roamed function in file
net/wireless/sme.c.
/* internal error -- how did we get to CONNECTED w/o BSS? */
if (WARN_ON(!wdev->current_bss)) {
return;
}
To resolve the issue we report the BSS whenever we send a connect or
roam event to the cfg.
kvalo: fix style issues
Signed-off-by: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Kalle Valo <kalle.valo@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Done via perl script:
$ cat remove_semi_switch.pl
my $match_balanced_parentheses = qr/(\((?:[^\(\)]++|(?-1))*\))/;
my $match_balanced_braces = qr/(\{(?:[^\{\}]++|(?-1))*\})/;
foreach my $file (@ARGV) {
my $f;
my $text;
my $oldtext;
next if ((-d $file));
open($f, '<', $file)
or die "$P: Can't open $file for read\n";
$oldtext = do { local($/) ; <$f> };
close($f);
next if ($oldtext eq "");
$text = $oldtext;
my $count = 0;
do {
$count = 0;
$count += $text =~ s@\b(switch\s*${match_balanced_parentheses}\s*)${match_balanced_braces}\s*;@"$1$3"@egx;
} while ($count > 0);
if ($text ne $oldtext) {
my $newfile = $file;
open($f, '>', $newfile)
or die "$P: Can't open $newfile for write\n";
print $f $text;
close($f);
}
}
$
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The cfg80211 ops for power management were completely
broken. If we were asked for to go into power save it was putting
device in awake, and when we were asked to become awake we were
putting the device into power save... This fixes the powersave
operations to do the right thing.
Signed-off-by: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a scan operation is pending and in between a disconnect
event is received from firmware the scan results never get
sent back to cfg80211. This causes a scan failure and yields
a device/resource busy state upon retries. If a disconnect
event is received and scan is pending return the scan done
to the cfg80211 to enable futher scans to be issued.
Signed-off-by: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The firmware expects the device ID to be added on the
data and command packets sent to firmware for AR6003 v2.1.1.
Signed-off-by: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These commands and event IDs are used by AR6003 v2.1.1.
Some events are no longer needed so these are removed now.
Signed-off-by: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for AR6003 v2.1.1. Highlights changes
for this new hardware are:
1. Host interest area, through which driver communicates
with FW has been enhanced to accomodate additional
members for proper functioanlity of new HW.
2. The firmware and the board data files are different
for AR6003 v2.1.1. The capability to read those file
have been added in the driver.
3. Certain parameters like numdevice, firmware mode needs to be
programmed for proper functionality of new driver.
Signed-off-by: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1) ATH6K_CONFIG_HIF_VIRTUAL_SCATTER needs to be
ATH6KL_CONFIG_HIF_VIRTUAL_SCATTER in file ar6000_drv.h
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was done to handle a number of conflicts, the majority of which
were caused by the big "fix spelling issues" patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was empty code, WTF^pi.
Cc: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds