Erratum A-008585 says that the ARM generic timer counter "has the
potential to contain an erroneous value for a small number of core
clock cycles every time the timer value changes". Accesses to TVAL
(both read and write) are also affected due to the implicit counter
read. Accesses to CVAL are not affected.
The workaround is to reread TVAL and count registers until successive
reads return the same value. Writes to TVAL are replaced with an
equivalent write to CVAL.
The workaround is to reread TVAL and count registers until successive reads
return the same value, and when writing TVAL to retry until counter
reads before and after the write return the same value.
The workaround is enabled if the fsl,erratum-a008585 property is found in
the timer node in the device tree. This can be overridden with the
clocksource.arm_arch_timer.fsl-a008585 boot parameter, which allows KVM
users to enable the workaround until a mechanism is implemented to
automatically communicate this information.
This erratum can be found on LS1043A and LS2080A.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Scott Wood <oss@buserror.net>
[will: renamed read macro to reflect that it's not usually unstable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Engicam providing design services of electronic systems with
high content of technology, relying on a long experience in
electronic design.
For more info visit
http://www.engicam.com/en/
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This erratum describes a bug in logic outside the core, so MIDR can't be
used to identify its presence, and reading an SoC-specific revision
register from common arch timer code would be awkward. So, describe it
in the device tree.
Signed-off-by: Scott Wood <oss@buserror.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Silead Inc.specializes in touchscreen technology and got recently
introduced in a binding for the gsl1680 i2c touchscreen.
Therefore add the needed vendor-prefix as well.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
When using GPIO irqchip helpers to setup irqchip for a gpiolib based
driver, it is not possible to select which GPIOs to add to the IRQ domain.
Instead it just adds all GPIOs which is not always desired. For example
there might be GPIOs that for some reason cannot generated normal
interrupts at all.
To support this we add a flag irq_need_valid_mask to struct gpio_chip. When
this flag is set the core allocates irq_valid_mask that holds one bit for
each GPIO the chip has. By default all bits are set but drivers can
manipulate this using set_bit() and clear_bit() accordingly.
Then when gpiochip_irqchip_add() is called, this mask is checked and all
GPIOs with bit is set are added to the IRQ domain created for the GPIO
chip.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic NAND DT bindings allows one to tweak the ECC strength and
step size to their need. It can be used to lower the ECC strength to
match a bootloader/firmware config, but might also be used to get a better
reliability.
In the latter case, the user might want to use the maximum ECC strength
without having to explicitly calculate the exact value (this value not
only depends on the OOB size, but also on the NAND controller, and can
be tricky to extract).
Add a generic 'nand-ecc-maximize' DT property and the associated
NAND_ECC_MAXIMIZE flag, to let ECC controller drivers select the best
ECC strength and step-size on their own.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Remove "default" keyword from blue-and-red-wiring devicetree property
binding document. The code does not support and there is no intention
to support it.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
It is now unused, remove it before someone else thinks its a good idea
to use this.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds 3 more clocks to Exynos4 ISP driver. Enabling them is
needed to make the hardware operational. Till now it worked only because
those clocks were registered with IGNORE_UNUSED flag and were enabled
by default after SoC reset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by linuxdoc[1] tool, using:
$ for i in $(git grep kernel-doc Documentation/media/kapi/|cut -d: -f4); do kernel-lintdoc --sloppy $i; done
include/media/v4l2-dev.h:118 :WARN: function name from comment differs: v4l2_prio_close <--> v4l2_prio_check
include/media/v4l2-mc.h:56 [kernel-doc WARN] : enum name from comment differs: if_vid_dec_index <--> if_vid_dec_pad_index
include/media/v4l2-mc.h:71 [kernel-doc WARN] : enum name from comment differs: if_aud_dec_index <--> if_aud_dec_pad_index
include/media/v4l2-mem2mem.h:396 [kernel-doc WARN] : function name from comment differs: v4l2_m2m_num_src_bufs_ready <--> v4l2_m2m_num_dst_bufs_ready
drivers/media/dvb-core/dvb_math.h:28 [kernel-doc WARN] : function name from comment differs: cintlog2 <--> intlog2
include/media/v4l2-subdev.h:215 [kernel-doc WARN] : struct name from comment differs: s_radio <--> v4l2_subdev_tuner_ops
include/media/v4l2-subdev.h:890 [kernel-doc WARN] : function name from comment differs: v4l2_set_subdevdata <--> v4l2_set_subdev_hostdata
include/media/v4l2-subdev.h:901 [kernel-doc WARN] : function name from comment differs: v4l2_get_subdevdata <--> v4l2_get_subdev_hostdata
drivers/media/dvb-core/dvb_ringbuffer.h:196 [kernel-doc WARN] : function name from comment differs: dvb_ringbuffer_writeuser <--> dvb_ringbuffer_write_user
include/media/videobuf2-core.h:399 [kernel-doc WARN] : struct name from comment differs: vb2_ops <--> vb2_buf_ops
include/media/media-entity.h:132 [kernel-doc ERROR] : duplicate parameter definition 'source'
include/media/media-entity.h:477 [kernel-doc WARN] : function name from comment differs: media_entity_enum_test <--> media_entity_enum_test_and_set
include/media/media-entity.h:535 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> gobj_to_pad
include/media/media-entity.h:544 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> gobj_to_link
include/media/media-entity.h:553 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> gobj_to_intf
include/media/media-entity.h:562 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> intf_to_devnode
include/media/rc-core.h:234 [kernel-doc WARN] : function name from comment differs: rc_open <--> rc_close
include/media/v4l2-ctrls.h:397 [kernel-doc WARN] : missing initial short description of 'v4l2_ctrl_handler_init'
include/media/v4l2-dev.h:118 [kernel-doc WARN] : function name from comment differs: v4l2_prio_close <--> v4l2_prio_check
include/media/v4l2-event.h:225 [kernel-doc WARN] : missing initial short description of 'v4l2_src_change_event_subscribe'
[1] https://return42.github.io/linuxdoc/linux.html
The above are real issues at the documentation. On several cases,
caused by cut-and-paste.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the dts property for the capability if TRGMII supported on GAMC0
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a few indentation issues to enable automated table reorganization
by a regex-based script.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds documentation of device tree bindings for the
STM32 USART
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inode_change_ok() will be resposible for clearing capabilities and IMA
extended attributes and as such will need dentry. Give it as an argument
to inode_change_ok() instead of an inode. Also rename inode_change_ok()
to setattr_prepare() to better relect that it does also some
modifications in addition to checks.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Again move it from the unmaintainable csv into DOC free-form overview
sections.
v2: Types Lionel&Sean spotted.
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1474448370-32227-6-git-send-email-daniel.vetter@ffwll.ch
Try to spec a bit more precisely how they all fit together, now that
at least the code is for all the additional properties is in one
place.
Also remove the entries for the standardized properties from the
table, because that thing is supremely unmaintaineable.
v2: Fix typos Sean spotted.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1474448370-32227-4-git-send-email-daniel.vetter@ffwll.ch
Big thing is untangling and carefully documenting the different uapi
types of planes. I also sprinkled a few more cross references around
to make this easier to discover.
As usual, remove the kerneldoc for internal functions which are not
exported. Aside: We should probably go OCD on all the ioctl handlers
and consistenly give them an _ioctl postfix.
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1474448370-32227-2-git-send-email-daniel.vetter@ffwll.ch
Just pure code movement, cleanup and polish will happen in later
patches.
v2: Don't forget all the ioctl! To extract those cleanly I decided to
put check_src_coords into drm_framebuffer.c (and give it a
drm_framebuffer_ prefix), since that just checks framebuffer
constraints.
v3: rebase over PAGE_FLIP_TARGET.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[seanpaul]
This patch as posted on the list was rebased on:
commit 6f00975c61
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Aug 20 12:22:11 2016 +0200
drm: Reject page_flip for !DRIVER_MODESET
so as a result of moving the page_flip ioctl, this fix has
been rolled into this patch.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Recent discussion has made it clear that there is no community consensus on
this particular rule. Remove it now, lest it inspire yet another set of
unwanted "cleanup" patches.
This partially reverts 865a1caa4b (CodingStyle: Clarify and complete
chapter 7).
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add cross references for the development process documents
that were converted to ReST:
Documentation/SubmitChecklist
Documentation/SubmittingDrivers
Documentation/SubmittingPatches
Documentation/development-process/development-process.rst
Documentation/stable_kernel_rules.txt
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
As this file is mentioned at the development-process/ book,
let's convert it to ReST markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- Add pinctrl and clk support for the Orion5x SoC mv88f5181 variant
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfiWTAACgkQCwYYjhRyO9X3ZQCfdOuvxXIajKkmxgvVwNgzEeLF
GEIAn1LYY/vmNikPhxH4O2FBi/9NBdZM
=GrPA
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-4.9-1' of git://git.infradead.org/linux-mvebu into next/drivers
Pull "mvebu drivers for 4.9 (part 1)" from Gregory CLEMENT:
- Add pinctrl and clk support for the Orion5x SoC mv88f5181 variant
* tag 'mvebu-drivers-4.9-1' of git://git.infradead.org/linux-mvebu:
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
Support configuration of ext_wakeup sources. This patch makes it
possible to enable ext_wakeup and set it's polarity, depending on board
configuration. AM335x's dedicated PMIC (tps65217) uses ext_wakeup to
notify about power-button presses. Handling power-button presses enables
to recover from RTC-only power states correctly.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As far as I'm aware the mv88f5181-b1 and mv88f5181l are the same at the
pinctrl level, so re-use the definitions for both.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Referring to the u-boot sources for the Netgear WNR854T, add support
for the mv88f5181.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reorder the on-line documents based on their timestamp or
copyright notes. More updated documents come first.
While here, add the number of pages for POSIX4 document.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is a way better to have a timestamp to help identifying
when something is too old.
So, retrieve the dates marked on the existing documents.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are still some broken docs: the URLs point to somewhere,
however, the texts are not there anymore. I was able to
find the texts on other URLs for some of those, but they're all
too old. So, just get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are three places where it mentions in-kernel docs.
Move them to a separate topic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The Linux Kernel - This book is for Kernel 2.0.33
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add two books from my own bookshelf. I found them useful by
the time I bought; so it could be useful to others ;)
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Instead of using a random order, place the books on publication
date, from the newest to the oldest.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- remove LDD versions 1 and 2, as there's already an entry for
LDD3;
- add a link between LDD online and published entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- Use lower case for sections, as this is the standard used on
the other ReST files;
- The latest version of this document is at the Kernel source, and
not at the listed URL. So, move it to the end of the doc.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This introduces a consistent indenting of 4 spaces for all
lists.
[mchehab@s-opensource.com: rebased to apply before rename]
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Background/Reasoning:
Books:
------
* Linux Kernel Networking by Rami Rosen
While some parts are quite short and could be
more carefully explained it's still a good recomendation
for understanding linux kernel networking, (IMHO)
* Linux Treiber entwickeln:
It sure is a drawback that this is a german book.
But it's quite recent, well structured and there are also
other non-english (spanish) books/papers in this list.
Papers:
-------
* On Submitting kernel Patches
Contains 2 case studies of bigger patch sets and how (or how not)
they were merged. I found it helpful
* Tracing the Way of Data in a TCP Connection through the Linux Kernel
Since this was written by me this inclusion may be a bit biased :p
Neitherless I think this gives a good introduction on
understanding/exploring linux internals using ftrace and an overview
of Linux TCP internals.
[mchehab@s-opensource.com: rebased to apply before rename]
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dots at the ends of the list elements introduced
unnecesarry newlines in the "compiled" document.
While this was not "mission critical" it's not nice to look at
either.
[mchehab@s-opensource.com: rebased to apply before rename]
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This removes all dead links to online docs which
are dead according to Jon and Mauro in
https://lkml.kernel.org/r/20160916182849.2a7101ea () vento ! lan
Additionally some references to very old articles refering to
linux 2.2 and 2.0 are deleted.
[mchehab@s-opensource.com: rebased to apply before rename]
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro's patch set introduced some bare :: lines; these can be represented
by a double colon at the end of the preceding text line. The result looks
a little less weird and is less verbose.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- use ``foo`` to markup inline literal stuff, effectively making it
to be presented as a monospaced font when parsed by Sphinx;
- the markup below the title should have the same length as the
title;
- Fix the list markups, from "1:" to "1)";
- Split item 2 into a separate list for the build options, in order
to be presented as a list on Sphinx;
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Task 11 (kernel-doc) still mentions usage of make manpages, but
this won't work if the API is documented via Sphinx. So, update
it to use either htmldocs or pdfdocs, with are the documentation
targets that work for all.
While here, add ReST reference to the kernel documentation book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- A few link references were missing http://
- Several sites are now redirecting to https protocol. On such
cases, just use the https URL.
NOTE: all URLs were checked and they're pointing to the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Do a series of minor improvements at the ReST output format:
- Instead of using the quote blocks (::) for quotes, use
italics. That looks nicer on epub (and html) output, as
no scroll bar will be added. Also, it will adjust line
breaks on the text automatically.
- Add a missing reference to SubmittingPatches.rst and use
**foo** instead of _foo_.
- use bold for "The Perfect Patch" by removing a newline.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The description there are pre-Sphinx. Update it to cover the
new way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add cross references for the documents mentioned at HOWTO and
are under the Documentation/ directory, using the ReST notation.
It should be noticed that HOWTO also mentions the /README file.
We opted to not touch it, for now, as making it build on
Sphinx would require it to be moved to a Documentation/foo
directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Do a few changes to make the output look better:
- use bullets on trivial patches list;
- use monotonic font for tools name;
- use :manpage:`foo` for man pages;
- don't put all references to maintainer*html at the same line.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- Change the sections to use ReST markup;
- Add cross-references where needed;
- convert aspas to verbatim text;
- use code block tags;
- make Sphinx happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- Change the document title markup to make it on a higher level;
- Add blank lines as needed, to improve the output;
- use italics for the country-code at kernel.org ftp URL.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- use ReST markups for section headers;
- add cross-references to the options;
- mark code blocks;
- a few minor changes to make Sphinx happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add markups for it to be properly parsed by Sphinx.
As people browsing this document may not notice that the source
file title is "stable_api_nonsense", I opted to use bold to
the rationale for this document. I also found it better to
add a note when it says that the nonsense applies only to the
kABI/kAPI, and not to uAPI.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a name for the document and convert the sections to
ReST markups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- Convert document name to ReST;
- Convert footnotes;
- Convert sections to ReST format;
- Don't use _foo_, as Sphinx doesn't support underline. Instead,
use bold;
- While here, remove whitespaces at the end of lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are two places there where there are notes that should
be highlighted. So, use the ReST note markup for such texts.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Sphinx doesn't accept underline markups by purpose.
While there are ways to support underline via CSS, this won't
be portable with non-html outputs.
As we want CodingStyle to do emphasis, replace _foo_ by **foo**,
using bold emphasis.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
On Sphinx/ReST notation, ``foo`` means that foo will be will be
marked as inline literal, effectively making it to be presented
as a monospaced font.
As we want this document to be parsed by Sphinx, instead of using
"foo", use ``foo`` for the names that are literal, because it is an
usual typographic convention to use monospaced fonts for functions
and language commands on documents, and we're following such
convention on the other ReST books.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- Fix all chapter identation;
- add c blocks where needed;
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
As discussed at linux-doc ML, the best is to keep all documents
backward compatible with Sphinx version 1.2, as it is the latest
version found on some distros like Debian.
All books currently support it.
Please notice that, while it mentions the eventual need of
XeLaTex and texlive to build pdf files, this is not a minimal
requirement, as one could just be interested on building html
documents. Also, identifying the minimal requirements for
texlive packages is not trivial, as each distribution seems to
use different criteria on grouping LaTex functionalities.
While here, update the current kernel version to 4.x.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- Fix chapter identation inconsistencies;
- Convert table to ReST format;
- use the right tag for bullets;
- Fix bold emphasis;
- mark blocks with :: tags;
- use verbatim font for files;
- make Sphinx happy
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document is old: it is from Kernel v2.6.12 days.
Update it to the current status, and add a reference for the
linux-next tree.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- use the correct markup to identify each section;
- Add some blank lines for Sphinx to properly interpret
the markups;
- Remove a blank space on some paragraphs;
- Fix the verbatim and bold markups;
- Cleanup the remaining errors to make Sphinx happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document is almost compliant with ReST notation, but some
small adjustments are needed to make it parse properly by
Sphinx (mostly, add blank lines where needed).
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Now that the files at Documentation/development-process/
were converted to ReST, make create a book at Sphinx.
As we'll have other books related to the development process,
we'll add it as a sub-book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Now that the documents were converted, rename them to .rst, as
this is needed by the Sphinx build logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document is on good shape for ReST: all it was needed was
to fix the section markups, add a toctree, convert the tables
and add a few code/quote blocks.
While not strictly required, I opted to use lowercase for
the titles, just like the other books that were converted
to Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're about to use those two markups, add them to the
theme style overrride.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Starting with sama5d4, the crystal oscillator is always enabled at startup
and the SCKC doesn't have an OSC32EN bit anymore.
Add support for that new controller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Multi-cpu support is useful to improve the performance of kdump in
some cases. So add the description of enable multi-cpu support in
dump-capture kernel.
Signed-off-by: Zhou Wenjian <zhouwj-fnst@cn.fujitsu.com>
Acked-by: Baoquan He <bhe@redhat.com>
Acked-by: Xunlei Pang <xpang@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
nr_cpus can help to save memory. So we should remind user of it.
Signed-off-by: Zhou Wenjian <zhouwj-fnst@cn.fujitsu.com>
Acked-by: Baoquan He <bhe@redhat.com>
Acked-by: Xunlei Pang <xpang@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Move mic/mpssd examples to samples and remove it from Documentation
Makefile. Create a new Makefile to build mic/mpssd. It can be built
from top level directory or from mic/mpssd directory:
Run make -C samples/mic/mpssd or cd samples/mic/mpssd; make
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Remove networking from Documentation Makefile to move the test to
selftests. Update networking/timestamping Makefile to work under
selftests. These tests will not be run as part of selftests suite
and will not be included in install targets. They can be built and
run separately for now.
This is part of the effort to move runnable code from Documentation.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Remove watchdog-test from Makefile to move the test to selftests.
Add Makefile and .gitignore for watchdog-test. watchdog-test will
not be run as part of selftests suite and will not be included in
install targets. It can be built separately for now.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Remove ia64 from Makefile to move the test to selftests.
Update ia64 Makefile to work under selftests. ia64 will not be run as part
of selftests suite and will not be included in install targets. They can be
built separately for now.
The original Makefile built this test on all archirectures and this update
doesn't change that.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Remove vDSO from Makefile to move the to selftests. Update vDSO Makefile
to work under selftests. vDSO will not be run as part of selftests suite
and will not be included in install targets. They can be built separately
for now.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Remove ptp from Makefile to move the test to selftests. Update ptp Makefile
to work under selftests. ptp will not be run as part of selftests suite and
will not be included in install targets. They can be built separately for
now.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Move prctl tests from Documentation/prctl to selftests/prctl.
Remove prctl from Makefile to move the test. Update prctl Makefile to work
under selftests. prctl will not be run as part of selftests suite and will
not be included in install targets. They can be built separately for now.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Move dnotify_test.c, Makefile, and .gitignore from Documentation/filesystems
to selftests/filesystems.
Remove filesystems build target from Documentation/Makefile and update
selftests/filesystems/Makefile to work under selftests. dnotify_test will
not be run as part of selftests suite and will not be included in install
targets. It can be built separately for now.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Suggested patch solves two issues:
1) Currently documentation is unclear whether `make kselftest` should
be run before or after kernel was installed and booted. `make help`
gives a clear answer on that: "kselftest - Build and run kernel selftest
(run as root). Build, install, and boot kernel before running kselftest
on it."
2) Documentation states that `make kselftest` executes "unit" tests.
Technically it's not a _unit_ test if it requires to install an
application first. It's either integration or system test. To not to
confuse a user I suggest not to use a word "unit".
Signed-off-by: Aleksander Alekseev <afiskon@devzen.ru>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Add some documentation for the 64-bit syscall ABI, which doesn't seem
to be documented elsewhere.
This attempts to document existing practice. The only small discrepancy
is glibc clobbers not quite matching the kernel (e.g., xer, some
vsyscalls trash cr1 whereas glibc only clobbers cr0). These will be
resolved after this document is merged.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Add initial DTS support for ZTE ZX296718 SoC and ZX296718 EVB board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX22SoAAoJEFBXWFqHsHzOypkIAIj88TKFW6IWuiM+mFwu2Q3X
3sqKB11szxucCd8XYHUQ/wknZX33sDSj63mUbYN20Mb4AbA7u1KG/hR6mBIq3no7
xnIDixq6kIMmt3dY6OEgu3qlkEQnrbopcp7bt3N1QtXNtQazt5WWStSzBwAz1Qsq
QQMUjoOyp3sx3E48HiAmPo2R8oh231w44aKS87YU7IIa3Ld9SyNW6/t8sAAhqvWH
1DLFNgZ968jmbb46BylPSHslMSmjrv1HR+5nZ3zNOQeDcRvLqi7+z9xqhwJUVr08
DXh90RaZNSULHlMWL3lEBLR9KTlca2+08c4ax5YOVeAQjaf+ZUAQUPGod+IBW7M=
=KfUg
-----END PGP SIGNATURE-----
Merge tag 'zte-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Pull "ZTE arm64 device tree changes for 4.9" from Shawn Guo:
- Add initial DTS support for ZTE ZX296718 SoC and ZX296718 EVB board.
* tag 'zte-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: Add ZTE ZX296718 SoC dts and Makefile
Merge back from docs-next in order to get the cdomain extension.
With such extension, the number of warnings when building docs
in nitpick mode reduced from 22 to 2 warnings.
* docs-next/docs-next:
docs/driver-model: fix typo
DMA-API-HOWTO: <asm/generic/scatterlist.h> is no more
doc-rst:c-domain: function-like macros arguments
doc-rst:c-domain: fix sphinx version incompatibility
Documentation/filesystems: Fixed typo
docs: Don't format internal MPT docs
docs: split up serial-interfaces.rst
docs: Pull the HSI documentation together
docs: Special-case function-pointer parameters in kernel-doc
docs: make kernel-doc handle varargs properly
x86: fix memory ranges in mm documentation
documentation/scsi: Remove nodisconnect parameter
doc: ioctl: Add some clarifications to botching-up-ioctls
docs: split up the driver book
Docs: sphinxify device-drivers.tmpl
This patch removes support for STiH415/6 SoC's from the
st-restart dt binding documentation, as support for these
platforms is being removed from the kernel. It also updates
the dt example to a currently supported platform.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <linux-pm@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Changeset ab6343956f9c ("[media] V4L2: Add documentation for SDI timings
and related flags") added documentation for new V4L2 defines, but
it forgot to update videodev2.h.rst.exceptions to point to where
the documentation for those new values will be inside the book,
causing those warnings:
Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-dv-bt-std-sdi (if the link has no caption the label must precede a section header)
Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-dv-fl-first-field-extra-line (if the link has no caption the label must precede a section header)
Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-in-st-no-v-lock (if the link has no caption the label must precede a section header)
Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-in-st-no-std-lock (if the link has no caption the label must precede a section header)
Fixes: ab6343956f9c ("[media] V4L2: Add documentation for SDI timings and related flags")
Cc: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the kernel parameter nfs.callback_nr_threads to set
the number of threads that will be assigned to the callback channel.
Add support for the kernel parameter nfs.nfs.max_session_cb_slots
to set the maximum size of the callback channel slot table.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
- media: update IR support for newer SoCs
- firmware: add secure monitor driver
- net: new stmmac glue driver
- usb: udd DWC2 support for meson-gxbb
- clocks: expose more clock IDs for use by DT
- DT binding updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DlpW
-----END PGP SIGNATURE-----
Merge tag 'amlogic-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/late
Pull "Amlogic driver updates for v4.9, 2nd round" from Kevin Hilman:
- media: update IR support for newer SoCs
- firmware: add secure monitor driver
- net: new stmmac glue driver
- usb: udd DWC2 support for meson-gxbb
- clocks: expose more clock IDs for use by DT
- DT binding updates
* tag 'amlogic-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (21 commits)
clk: gxbb: expose i2c clocks
clk: gxbb: expose USB clocks
clk: gxbb: expose spifc clock
clk: gxbb: expose MPLL2 clock for use by DT
Documentation: dt-bindings: Add documentation for the Meson USB2 PHYs
usb: dwc2: add support for Meson8b and GXBB SoCs
net: stmmac: update the module description of the dwmac-meson driver
net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC
stmmac: introduce get_stmmac_bsp_priv() helper
net: dt-bindings: Document the new Meson8b and GXBB DWMAC bindings
clk: meson-gxbb: Export PWM related clocks for DT
meson: clk: Add support for clock gates
gxbb: clk: Adjust MESON_GATE macro to be shared with meson8b
clk: meson: Copy meson8b CLKID defines to private header file
meson: clk: Rename register names according to Amlogic datasheet
meson: clk: Move register definitions to meson8b.h
clk: meson: Rename meson8b-clkc.c to reflect gxbb naming convention
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
media: rc: meson-ir: Add support for newer versions of the IR decoder
...
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NN8A
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Topic branch for Samsung DeviceTree cleanup for 4.9" from Krzysztof Kozłowski:
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
* tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
ARM: dts: exynos: Fix mismatched values of SD drive strengh configuration on exynos4415
ARM: dts: exynos: Fix mismatched value for SD4 pull up/down configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos542x/exynos5800
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5410
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5260
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5250
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4415
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4x12
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos3250
ARM: dts: exynos: Use common macros for pinctrl configuration
pinctrl: dt-bindings: samsung: Update documentation with new macros
pinctrl: dt-bindings: samsung: Add header with values used for configuration
1. Allow compile testing of exynos-mct clocksource driver on ARM64.
2. Document Exynos5433 PMU compatible (already used by clkout driver and more
will be coming soon).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WOAL
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Pull "Samsung drivers/soc update for v4.9" from Krzysztof Kozlowski:
1. Allow compile testing of exynos-mct clocksource driver on ARM64.
2. Document Exynos5433 PMU compatible (already used by clkout driver and more
will be coming soon).
* tag 'samsung-drivers-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
Add the dts property for the capability if the hardware supports LRO.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a typical IPvlan L3 setup where master is in default-ns and
each slave is into different (slave) ns. In this setup egress
packet processing for traffic originating from slave-ns will
hit all NF_HOOKs in slave-ns as well as default-ns. However same
is not true for ingress processing. All these NF_HOOKs are
hit only in the slave-ns skipping them in the default-ns.
IPvlan in L3 mode is restrictive and if admins want to deploy
iptables rules in default-ns, this asymmetric data path makes it
impossible to do so.
This patch makes use of the l3_rcv() (added as part of l3mdev
enhancements) to perform input route lookup on RX packets without
changing the skb->dev and then uses nf_hook at NF_INET_LOCAL_IN
to change the skb->dev just before handing over skb to L4.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the implementation of error handlers into sysfs.
[dchinner: Added lots more detail.]
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Add clock data arrays for all UniPhier SoCs with a binding document.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock is present on BCM53573 devices (including BCM47189) that use
Cortex-A7. ILP is a part of PMU (Power Management Unit) multi-function
device so we use syscon (and regmap) for it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Remove 0 from clk_init_data to silence sparse]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch configures the semi-synchronous mode of the video clocks
of clkgenD2.
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch allows fine tuning of the quads FS for audio clocks
accuracy.
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch reworks the clock binding to avoid too much detail in DT.
Now we have only compatible string per type of clock
(remark from Rob https://lkml.org/lkml/2016/5/25/492)
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
STiH415 and STiH416 platforms are no longer used.
these platforms will be deprecated for the next kernel.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This short series convers device-drivers.tmpl into the RST format, splits
it up, and sets up the result under Documentation/driver-api/. For added
fun, I've taken one top-level file (hsi.txt) and folded it into the
document as a way of showing the direction I'm thinking I would like things
to go. There is plenty more of this sort of work that could be done, to
say the least - this is just a beginning!
The formatted results can be seen at:
http://static.lwn.net/kerneldoc/driver-api/index.html
As part of the long-term task to turn Documentation/ into less of a horror
movie, I'd like to collect documentation of the driver-specific API here.
Arguably gpu/ and the media API stuff should eventually move here, though
we can discuss the color of that particular shed some other day.
Meanwhile, I'd appreciate comments on the general idea.
Handle signatures of function-like macros well. Don't try to deduce
arguments types of function-like macros.
Signed-off-by: Markus Heiser <markus.heiser@darmarIT.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The self.indexnode's tuple has changed in sphinx version 1.4, from a
former 4 element tuple to a 5 element tuple.
e6a5a3a92e
Signed-off-by: Markus Heiser <markus.heiser@darmarIT.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fixed a -> an typo.
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The JDI LT070ME05000 is a 7" panel with a 1200x1920 (WUXGA) resolution
and connected to DSI using four lanes.
Cc: Archit Taneja <archit.taneja@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds support for Innolux Corporation 10.1" G101ICE-L01 WXGA
(1280x800) LVDS panel to the simple-panel driver.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update examples in Samsung pinctrl dt-bindings with new macros coming
from header file.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
This patch documents the usage of Exynos5433 PMU (Power Management Unit)
compatible.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Document how the generic "iommus" binding should be used to describe ARM
SMMU stream IDs instead of the old "mmu-masters" binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We're about to ratify our use of the generic binding, so document it.
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The existing IOMMU bindings are able to specify the relationship between
masters and IOMMUs, but they are insufficient for describing the general
case of hotpluggable busses such as PCI where the set of masters is not
known until runtime, and the relationship between masters and IOMMUs is
a property of the integration of the system.
This patch adds a generic binding for mapping PCI devices to IOMMUs,
using a new iommu-map property (specific to PCI*) which may be used to
map devices (identified by their Requester ID) to sideband data for the
IOMMU which they master through.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add device-tree binding for ar8xxx switch families.
Cc: devicetree@vger.kernel.org
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull RCU changes from Paul E. McKenney:
- Expedited grace-period changes, most notably avoiding having
user threads drive expedited grace periods, using a workqueue
instead.
- Miscellaneous fixes, including a performance fix for lists
that was sent with the lists modifications (second URL below).
- CPU hotplug updates, most notably providing exact CPU-online
tracking for RCU. This will in turn allow removal of the
checks supporting RCU's prior heuristic that was based on the
assumption that CPUs would take no longer than one jiffy to
come online.
- Torture-test updates.
- Documentation updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add device tree support for ZX296718 SoC and evaluation board based
on it. Also document new values.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds a driver for the SoC-wide (AKA uncore) PMU hardware
found in APM X-Gene SoCs.
Signed-off-by: Tai Nguyen <ttnguyen@apm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Driver providing perf backend for the SoC-wide PMU hardware found
in APM X-Gene SoCs.
Signed-off-by: Tai Nguyen <ttnguyen@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
Make the following changes in the HDMI gpio bindings:
- Use "-gpios" as the suffix for all the gpio names
- Move all the gpios to optional, since there are platforms that use none
of them.
- The HPD gpio is a standard one, remove the "qcom,hdmi-tx-" prefix from
it.
- Remove the HDMI DDC clk/data gpios. They are just leftovers of an old
way to configure pinctrl properties.
- Add a missing lpm gpio used on some platforms.
Make the necessary changes in the driver to incorporate these changes.
There hasn't been any upstream DT that uses the HDMI bindings, so it's
okay to change and move around these properties.
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This makes it possible to create a set of LEDs for Mellanox systems:
"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410",
"msb7800", "msn2740", "msn2100".
Driver obtains LED devices according to system configuration, provided
through system DMI data, like mlxcpld:fan1:green, mlxcpld:fan1:red and
creates devices in form: "devicename:colour:function".
LED setting is controlled through on board CPLD Lattice device.
For setting particular LED off, solid, blink:
echo 0 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo timer > /sys/class/leds/mlxcpld\:status\:green/trigger
On module probing all LEDs are set green, on removing - off.
Last setting overwrites previous, f.e. sequence for
changing LED from green - red - green:
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:red/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
Note: LEDs cannot be turned on/off simultaneously.
The Kconfig currently controlling compilation of this code is:
drivers/leds/Kconfig:config LEDS_MLXCPLD
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
updated tag for 4.9 based on usb-next along with extcon merge
resolution
phy updates includes:
*) phy driver for USB 3.0 PHY on Northstar
*) phy driver for Rockchip usb2phy
*) phy driver for the Rockchip SoC internal PCIe PHY
*) phy driver for USB Type-C PHY on rk3399
*) phy_reset() API
*) support for Allwinner A64 usb phy, usb2 phy in r8a7796
*) Fixes in twl4030-usb, tegra phy, sun4i-usb phy, da8xx-usb phy
and omap-usb2 phy
*) other misc cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bI2e
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.9-updated_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
phy: for 4.9 (with extcon merge resolution)
updated tag for 4.9 based on usb-next along with extcon merge
resolution
phy updates includes:
*) phy driver for USB 3.0 PHY on Northstar
*) phy driver for Rockchip usb2phy
*) phy driver for the Rockchip SoC internal PCIe PHY
*) phy driver for USB Type-C PHY on rk3399
*) phy_reset() API
*) support for Allwinner A64 usb phy, usb2 phy in r8a7796
*) Fixes in twl4030-usb, tegra phy, sun4i-usb phy, da8xx-usb phy
and omap-usb2 phy
*) other misc cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the ST pinctrl dt doc and removes
references to these obsolete platforms. It also updates
the dt example to the currently supported STiH407
platform.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <linus.walleij@linaro.org>
Cc: <robh+dt@kernel.org>
Cc: <linux-gpio@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Support for new board OMAP-L138 LCDK
- Add AEMIF node on DA850 EVM and use it for NAND
- Audio support for LCDK
- Cleanups for PWM and UART
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7UMP
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.9/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "DaVinci DA850 device-tree enhancements include" from Sekhar Nori:
- Support for new board OMAP-L138 LCDK
- Add AEMIF node on DA850 EVM and use it for NAND
- Audio support for LCDK
- Cleanups for PWM and UART
* tag 'davinci-for-v4.9/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Audio support via simple-card
ARM: dts: da850,da850-evm: Add an aemif node and use it for the NAND
ARM: dts: da850: Add basic DTS for the LCDK
ARM: dts: da850: Add missing pin muxing for the UARTs
ARM: dts: da850: Add new ECAP and EPWM bindings
disable io watchdog for chipidea platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX2lExAAoJEEhZKYFQ1nG7xVkH/jfONzi6B0o1sPLwA5pF9PEz
mvkCUaXMRmgeHcHPviXjthfbZ6eKR7ddd0bxGC3DWd4eUOO3QohW9vI+wYhpKk//
mQh2F25nvZNYKOZ/BdG5XRZjVFT1qJGseknSg0TsRraAVEjOLdr7gqViPRAqMyoJ
PY3CQxlf8dqHz4ed5xsKmwcjGE9Q+A+YMhOXzxY2aLGTCaDNOcYNHJWIe9QXwOVQ
snxiNe+DoPkrspGrUJQpZ7lSq5siNxLS7cOlzYmWvxMkNw2A5xJgnoxoDziey8xo
2F427B0CwXyTC1gNBk721pIjIvkNcPAghoUo8EUgD71hC4nH8EFFM3iqA+U1xpc=
=hww9
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-testing
Peter writes:
Most of them are refine patches, only new feature is
disable io watchdog for chipidea platform.
please pull the following:
- Jon adds support for the Ethernet MAC DT nodes (AMAC) and provides the
following updates for Broadcom references boards:
* New Northstar Plus reference boards added: BCM958525er, BCM958522er,
BCM988312hr, BCM958623hr and BCM958622hr
* Add SATA nodes to the BCM958625hr and XMC boards
* Add I2C nodes to the XMC board
* Fixes the amount of RAM on BCM958625HR, BCM958625K and BCM958525XMC boards
* Add the GPIO reboot method for BCM958625hr and XMC boards
- Dhanajay adds PWM nodes for the Northstar Plus SoCs
- Rafal adds the USB 2.0 PHY to the BCM5301x Device Tree file include
- Stefan adds a missing USB clock to the BCM283x DT files, adds a DTSI file for
the USB host mode on BCM283x and finally documents and adds support for the
Raspberry Pi Zero
- Florian adds support for the Northstar Plus Switch Register Access block which
enables the integrated switch on these SoCs and enables the switch ports on the
BCM958625HR reference board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=j84Q
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.9/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.9" from Florian Fainelli:
This pull request contains Broadcom ARM-based Device Tree changes for v4.9,
please pull the following:
- Jon adds support for the Ethernet MAC DT nodes (AMAC) and provides the
following updates for Broadcom references boards:
* New Northstar Plus reference boards added: BCM958525er, BCM958522er,
BCM988312hr, BCM958623hr and BCM958622hr
* Add SATA nodes to the BCM958625hr and XMC boards
* Add I2C nodes to the XMC board
* Fixes the amount of RAM on BCM958625HR, BCM958625K and BCM958525XMC boards
* Add the GPIO reboot method for BCM958625hr and XMC boards
- Dhanajay adds PWM nodes for the Northstar Plus SoCs
- Rafal adds the USB 2.0 PHY to the BCM5301x Device Tree file include
- Stefan adds a missing USB clock to the BCM283x DT files, adds a DTSI file for
the USB host mode on BCM283x and finally documents and adds support for the
Raspberry Pi Zero
- Florian adds support for the Northstar Plus Switch Register Access block which
enables the integrated switch on these SoCs and enables the switch ports on the
BCM958625HR reference board
* tag 'arm-soc/for-4.9/devicetree' of http://github.com/Broadcom/stblinux: (22 commits)
ARM: dts: bcm2835: Add Raspberry Pi Zero
DT: bindings: bcm: Add Raspberry Pi Zero
ARM: dts: bcm283x: Add dtsi for USB host mode
ARM: dts: bcm283x: Add missing USB clock
ARM: dts: NSP: Add new DT file for bcm958622hr
ARM: dts: NSP: Add new DT file for bcm958623hr
ARM: dts: NSP: Add new DT file for bcm988312hr
ARM: dts: NSP: Add new DT file for bcm958522er
ARM: dts: NSP: Add new DT file for bcm958525er
ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file
ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file
ARM: dts: NSP: Specify RAM amount for BCM958525XMC board
ARM: dts: NSP: Specify RAM amount for BCM958625K board
ARM: dts: NSP: Enable SATA and add i2c devices on XMC
ARM: dts: NSP: Enable SATA on bcm958625hr
ARM: dts: NSP: Correct RAM amount for BCM958625HR board
ARM: dts: NSP: Add PWM Support to DT
ARM: BCM5301X: Specify PHY of USB 2.0 in DT
ARM: dts: NSP: Add BCM958625HR switch ports
ARM: dts: NSP: Add Switch Register Access Block node
...
Add support for big endian on the Allwinner A20, and the Nextthing GR8 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uNAt
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/soc
Pull "Allwinner core changes for 4.9" from Maxime Ripard:
Add support for big endian on the Allwinner A20, and the Nextthing GR8 SoC
* tag 'sunxi-core-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Support the Nextthing GR8
ARM: sunxi: enable big-endian
The ZX296718 clocks are statically listed and registered. More
clock will be added later.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Per the PCI Firmware spec, r3.0, sec 4.5.1, on ACPI systems, the OS must
not use AER unless _OSC is present and _OSC grants AER control to the OS.
The aerdriver.forceload kernel parameter was a way to enable Linux AER
support on ACPI systems that lack _OSC or fail to grant control the the OS.
Enabling Linux AER support when the firmware doesn't want us to is a recipe
for problems, e.g., the firmware might be handling AER itself.
Remove the aerdriver.forceload kernel parameter and related supporting
code.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The aerdriver.nosourceid kernel parameter was intended for working around
broken chipsets don't supply the source ID for AER events. We recently
added PCI_BUS_FLAGS_NO_AERSID, which can be set by quirks for the same
purpose.
Remove the aerdriver.nosourceid kernel parameter. For anything other than
debugging, asking users to find and use kernel parameters is a poor user
experience. Instead, we should add PCI_BUS_FLAGS_NO_AERSID quirks for any
hardware that needs it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- ACPI IORT core code
- IORT support for the GICv3 ITS
- A few of GIC cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Xhg0
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Merge the first drop of irqchip updates for 4.9 from Marc Zyngier:
- ACPI IORT core code
- IORT support for the GICv3 ITS
- A few of GIC cleanups
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
-----BEGIN PGP SIGNATURE-----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=V1xL
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
-----BEGIN PGP SIGNATURE-----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=vTFa
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.9 merge window
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
* 'clk-meson-gxbb' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: meson-gxbb: Export PWM related clocks for DT
meson: clk: Add support for clock gates
gxbb: clk: Adjust MESON_GATE macro to be shared with meson8b
clk: meson: Copy meson8b CLKID defines to private header file
meson: clk: Rename register names according to Amlogic datasheet
meson: clk: Move register definitions to meson8b.h
clk: meson: Rename meson8b-clkc.c to reflect gxbb naming convention
clk: meson: Fix invalid use of sizeof in gxbb_aoclkc_probe()
clk: meson: Add GXBB AO Clock and Reset controller driver
dt-bindings: clock: reset: Add GXBB AO Clock and Reset Bindings
clk: gxbb: add MMC gate clocks, and expose for DT
Add the documentation for the bindings for the Meson8b and GXBB USB2
PHYs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add compatible strings for amlogic Meson8b and GXBB SoCs with the
corresponding configuration parameters.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Four more SoCs converted to the new clock framework (A31, A31s, A23 and
A33).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ff/R
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Pull Allwinner clock driver changes from Maxime Ripard:
Four more SoCs converted to the new clock framework (A31, A31s, A23 and
A33).
* tag 'sunxi-clk-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi-ng: Add hardware dependency
clk: sunxi-ng: Add A23 CCU
clk: sunxi-ng: Add A33 CCU support
clk: sunxi-ng: Add N-class clocks support
clk: sunxi-ng: mux: Add mux table macro
clk: sunxi-ng: div: Allow to set a maximum
clk: sunxi-ng: div: Add kerneldoc for the _ccu_div structure
clk: sunxi-ng: div: Add mux table macros
clk: sunxi-ng: Add A31/A31s clocks
clk: sunxi-ng: mux: Add clk notifier functions
clk: sunxi-ng: mux: support fixed pre-dividers on multiple parents
clk: sunxi-ng: mux: Add support for mux tables
clk: sunxi-ng: mux: Rename mux macro to be consistent
clk: sunxi-ng: nkm: Add mux to support multiple parents
clk: sunxi-ng: mux: Increase fixed pre-divider div size
includes:
- addition of sound subsystem related clocks for Exynos5410 SoC
(EPLL, PDMA) and support for "samsung,exynos5410-audss-clock"
compatible in the clk-exynos-audss driver,
- addition of DRAM controller related clocks for exynos5420,
- MAINTAINERS update adding Chanwoo Choi as the Samsung SoC
clock drivers co-maintainer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lEKC
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.9-samsung' of git://linuxtv.org/snawrocki/samsung into clk-next
Pull samsung clk driver updates from Sylwester Nawrocki:
In addition to a few clean up and code consolidation patches this
includes:
- addition of sound subsystem related clocks for Exynos5410 SoC
(EPLL, PDMA) and support for "samsung,exynos5410-audss-clock"
compatible in the clk-exynos-audss driver,
- addition of DRAM controller related clocks for exynos5420,
- MAINTAINERS update adding Chanwoo Choi as the Samsung SoC
clock drivers co-maintainer.
* tag 'clk-v4.9-samsung' of git://linuxtv.org/snawrocki/samsung:
clk: samsung: Add support for EPLL on exynos5410
clk: samsung: clk-exynos-audss: Whitespace and debug trace cleanup
clk: samsung: clk-exynos-audss: Add exynos5410 compatible
clk: samsung: clk-exynos-audss: controller variant handling rework
clk: samsung: Use common registration function for pll2550x
clk: samsung: exynos5410: Expose the peripheral DMA gate clocks
clk: samsung: exynos5420: Add clocks for CMU_CDREX domain
clk: samsung: exynos5410: Use samsung_cmu_register_one() to simplify code
clk: samsung: exynos5260: Move struct samsung_cmu_info to init section
MAINTAINERS: Add myself as Samsung SoC clock drivers co-maintainer
clk: samsung: exynos5410: Add clock IDs for PDMA and EPLL clocks
clk: samsung: Add clock IDs for the CMU_CDREX (DRAM Express Controller)
Suppress fields that can be handled in driver using compatible string.
Rename compatibility strings accordingly.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added device tree bindings documentation for BRCMSTB, NSP, NS2 iProc
SoCs supported by spi-bcm-qspi, spi-brcmstb-qspi and spi-iproc-qspi driver.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull "Rockchip dts64 changes for 4.9" from Heiko Stübner:
64bit Rockchip devicetree changes containing support for the recently
added firmware reboot-flag support, one new board the Tronsmart Orion
based on the rk3368 and a large number of newly supported peripherals
for the rk3399 (type-c phy, usb2 phy, pcie controller and pcie phy,
gmac, arm-pmu using ppi partitioning, efuse, saradc) as well as some
smaller housekeeping and non-critical fixes.
* tag 'v4.9-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (22 commits)
arm64: dts: rockchip: add Type-C phy for RK3399
arm64: dts: rockchip: enable the gmac for rk3399 evb board
arm64: dts: rockchip: add the gmac needed node for rk3399
arm64: dts: rockchip: support the pmu node for rk3399
arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
arm64: dts: rockchip: add the tcpc for rk3399 power domain
arm64: dts: rockchip: add efuse0 device node for rk3399
arm64: dts: rockchip: configure PCIe support for rk3399-evb
arm64: dts: rockchip: add the PCIe controller support for RK3399
arm64: dts: rockchip: add the PCIe PHY for RK3399
arm64: dts: rockchip: add the gmac power domain on rk3399
arm64: dts: rockchip: Add pinctrl entry for 32k clock on rk3399
arm64: dts: rockchip: set to CCI clock of RK3399 to 600M
arm64: dts: rockchip: fix the address map for WDT0 and WDT1
arm64: dts: rockchip: add the saradc for rk3399
arm64: dts: rockchip: configure usb2-phy support for rk3399-evb
arm64: dts: rockchip: add usb2-phy support for rk3399
arm64: dts: rockchip: add syscon-reboot-mode DT node
soc: rockchip: add reboot-mode header
arm64: dts: rockchip: remove broken-cd from sdio0
...
This is the initial codec driver for both rt5663 rt5668 codec.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Set UART1 clock frequency to 150MHz for higher baud rates on hikey
- Add display subsystem, HDMI and cma nodes on hikey to support display
- Add syscon-reboot-mode support on hikey
- Add pstore support on hikey
- Add resets and sd-uhs-sdr property dwmmc ndoe on hikey
- Remove hip05_hns.dtsi since it can not be built without mbigenv1
- Update system controller bingding document for hip05 and hip06
- Add xge and sas support on hip06
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yhRv
-----END PGP SIGNATURE-----
Merge tag 'hisi-soc-dt-for-4.9' of git://github.com/hisilicon/linux-hisi into next/dt64
Pull "ARM64: DT: Hisilicon SoC DT updates for 4.9" from Wei Xu:
- Set UART1 clock frequency to 150MHz for higher baud rates on hikey
- Add display subsystem, HDMI and cma nodes on hikey to support display
- Add syscon-reboot-mode support on hikey
- Add pstore support on hikey
- Add resets and sd-uhs-sdr property dwmmc ndoe on hikey
- Remove hip05_hns.dtsi since it can not be built without mbigenv1
- Update system controller bingding document for hip05 and hip06
- Add xge and sas support on hip06
* tag 'hisi-soc-dt-for-4.9' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi6220: add sd-uhs- properties into dwmmc_1
arm64: dts: hi6220: add resets property into dwmmc nodes
arm64: dts: hikey: extend default cma size to 128MB
arm64: dts: hip06: Append sas node
arm64: dts: hip06: Append hns node
dt-bindings: hisilicon: Add Hip05 and Hip06 system controller support
arm64: dts: hip05: kill hip05_hns.dtsi
arm64: dts: hikey: Add pstore support for HiKey
arm64: dts: hikey: Add hikey support for syscon-reboot-mode
arm64: dts: Add HDMI node for hi6220-hikey
arm64: dts: Add display subsystem DT nodes for hi6220-hikey
arm64: dts: set UART1 clock frequency to 150MHz
This is a router based on the mv88f5181 chipset.
http://www.netgear.com/support/product/WNR854T.aspxhttp://wiki.openwrt.org/toh/netgear/wnr854t
[gregory.clement@free-electrons.com:
- extract dt part from "arm: orion5x: Add DT-based support for Netgear
WNR854T"
- squashed "arm: orion5x: Alias uart0 to serial0 for all orion5x" into
this commit and move serial0 alias from dtsi to dts]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
commit e1defc4ff0
"block: Do away with the notion of hardsect_size"
removed the notion of "hardware sector size" from
the kernel in favor of logical block size, but
references remain in comments and documentation.
Update the remaining sites mentioning hardsect.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Common definitions for the SoC for board definitions to use.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Copy the format for kirkwood/dove to orion5x
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Orion GPIO controller binding description in mrvl-gpio.txt is obsolete, and
duplicates the description in gpio-mvebu.txt.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Information about interrupts is exposed via /proc/interrupts, but the
format of that file has changed over kernel versions and differs across
architectures. It also has varying column numbers depending on hardware.
That all makes it hard for tools to parse.
To solve this, expose the information through sysfs so each irq attribute
is in a separate file in a consistent, machine parsable way.
This feature is only available when both CONFIG_SPARSE_IRQ and
CONFIG_SYSFS are enabled.
Examples:
/sys/kernel/irq/18/actions: i801_smbus,ehci_hcd:usb1,uhci_hcd:usb7
/sys/kernel/irq/18/chip_name: IR-IO-APIC
/sys/kernel/irq/18/hwirq: 18
/sys/kernel/irq/18/name: fasteoi
/sys/kernel/irq/18/per_cpu_count: 0,0
/sys/kernel/irq/18/type: level
/sys/kernel/irq/25/actions: ahci0
/sys/kernel/irq/25/chip_name: IR-PCI-MSI
/sys/kernel/irq/25/hwirq: 512000
/sys/kernel/irq/25/name: edge
/sys/kernel/irq/25/per_cpu_count: 29036,0
/sys/kernel/irq/25/type: edge
[ tglx: Moved kobject_del() under sparse_irq_lock, massaged code comments
and changelog ]
Signed-off-by: Craig Gallek <kraig@google.com>
Cc: David Decotigny <decot@google.com>
Link: http://lkml.kernel.org/r/1473783291-122873-1-git-send-email-kraigatgoog@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Adding over-current-active-high to indicate the over current flag
is high active as typically we use active low for over current
polarity.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Add compatible string for imx7d-usbmisc.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
A second set of device tree changes, this time switching a few SoCs to the
new sunxi-ng clock framework. We also added the support for a new SoC
(NextThing GR8 and its evaluation board), and the support for the DRM
driver in the A33.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uy/t
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/late
Merge "Allwinner DT changes for 4.9, take 2" from Maxime Ripard:
A second set of device tree changes, this time switching a few SoCs to the
new sunxi-ng clock framework. We also added the support for a new SoC
(NextThing GR8 and its evaluation board), and the support for the DRM
driver in the A33.
To maintain bisectability, while avoiding some un-trivial merge
conflicts, I had to merge the clk branch that I've sent a PR to Mike
and Stephen. This branch will of course be stable.
* tag 'sunxi-dt-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (53 commits)
ARM: dts: gr8: Add support for the GR8 evaluation board
ARM: dts: Add NextThing GR8 dtsi
ARM: dts: sun8i: Move A23/A33 usbphy and usb_otg nodes to common dtsi
ARM: sun8i: a23/a33: Add RGB666 pins
ARM: sun8i: a33: Add display pipeline
ARM: sun8i: Convert the A23 and A33 to the CCU
ARM: dts: sun6i: switch A31/A31s to new CCU clock bindings
clk: sunxi-ng: Add hardware dependency
clk: sunxi-ng: Add A23 CCU
clk: sunxi-ng: Add A33 CCU support
clk: sunxi-ng: Add N-class clocks support
clk: sunxi-ng: mux: Add mux table macro
clk: sunxi-ng: div: Allow to set a maximum
clk: sunxi-ng: div: Add kerneldoc for the _ccu_div structure
clk: sunxi-ng: div: Add mux table macros
devicetree: Add vendor prefix for FriendlyARM
ARM: dts: sun8i: Add dts file for the NanoPi NEO SBC
ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers
ARM: dts: sun8i: Add dts file for the Orange Pi Plus2E SBC
ARM: dts: sun8i: Orange Pi Plus dts is for the Plus and Plus 2
...
-----BEGIN PGP SIGNATURE-----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=C78b
-----END PGP SIGNATURE-----
Merge tag 'clcd-nomadik' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "CLCD graphics on the Nomadik NHK15" from Linus Walleij:
* tag 'clcd-nomadik' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: add the CLCD LCD display to the NHK15
ARM: dts: add PMU to the NHK15 device tree
ARM: nomadik: select MFD_SYSCON
dt-bindings: Add TPO TPG110 binding
dt-bindings: add vendor TPO
ARM: dts: add STMPE PWM to the NHK15 device tree
- Add SoC support for i.MX7 Solo which is a reduced version of i.MX7
Dual.
- New board support: Gateworks Ventana i.MX6Q/DL GW553x, Inverse Path
i.MX53 USB armory, i.MX6Q/DL TS-4900 from Technologic Systems,
i.MX6UL GEA M6UL modules from Engicam, i.MX7 Solo Warp7 board.
- Add DMA and IPU CSI devices for i.MX53 SoC support.
- Refine i.MX7 Dual SoC DTS as a preparation of i.MX7 Solo support.
- Use of_graph dt nodes to describe the panel for vf610-colibri and
ls1021a-twr boards.
- Add gpio-ranges property to i.MX6 GPIO controllers, which will be
useful when GPIO driver is changed to request pad configuration as
GPIO function.
- Random device additions or small changes for various board support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX1lb5AAoJEFBXWFqHsHzOBI0H/1ynv4DnmCds1eBS8yjqYJnH
bM02BSwV2gwVQaDljTJCDNoDFMGM3aNjnWge1v4UsfIyDPploMCFi4ympPNsCx3w
VYB+TRQFG6WHIyd6lHBd+VqeTNgPz+LAhpdrNloZecUUIBlpD8i+8WpDw45ufE7b
A7jRIaFWnBjMEsUsG/To5PQDI17YwtkRaht2gq+3rwRdk2hbeVlg05JUcwn1+eBB
DnccJUTy4zZd09W7MRMRM2FejYCququCCfH4is8+1iVLVixwpjEKBHA2w8GatLtn
e8T+ie/FWIizlnK4Jadba1tcRmW8PlX6UAzgWjGia27G6deHQ1x/0YL9eqDsAP0=
=CNTd
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree changes for 4.9" from Shawn Guo:
- Add SoC support for i.MX7 Solo which is a reduced version of i.MX7
Dual.
- New board support: Gateworks Ventana i.MX6Q/DL GW553x, Inverse Path
i.MX53 USB armory, i.MX6Q/DL TS-4900 from Technologic Systems,
i.MX6UL GEA M6UL modules from Engicam, i.MX7 Solo Warp7 board.
- Add DMA and IPU CSI devices for i.MX53 SoC support.
- Refine i.MX7 Dual SoC DTS as a preparation of i.MX7 Solo support.
- Use of_graph dt nodes to describe the panel for vf610-colibri and
ls1021a-twr boards.
- Add gpio-ranges property to i.MX6 GPIO controllers, which will be
useful when GPIO driver is changed to request pad configuration as
GPIO function.
- Random device additions or small changes for various board support.
* tag 'imx-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (41 commits)
ARM: dts: add gpio-ranges property to iMX GPIO controllers
ARM: dts: imx35: add iim module to imx35.dtsi
ARM: dts: vf610-colibri: use of_graph dt nodes to describe the panel
ARM: dts: ls1021a: Add of_graph dt nodes to describe the panel
ARM: dts: imx53: add support for USB armory board
devicetree: Add vendor prefix for Inverse Path
ARM: dts: imx7s-warp: Add Bluetooth support
ARM: dts: imx7s-warp: Add User Button support
ARM: dts: imx7s-warp: Enable I2C2 device support
ARM: dts: imx6ul-geam: Add Engicam IMX6UL GEA M6UL initial support
ARM: dts: imx6ul iomuxc syscon is compatible to imx6q
ARM: dts: imx7-colibri: add Audio support
ARM: dts: imx7-colibri: add basic supply regulators
ARM: dts: imx7-colibri: move SD-card to module level
ARM: dts: imx6sx: Add GPU bindings
ARM: dts: imx7s-warp: Let the codec control MCLK pinctrl
ARM: dts: imx6ul-pico-hobbit: Use WDOG_B pin reset
ARM: dts: imx6q-bx50v3: configure unused pca953x pins
ARM: dts: imx6sx: document SION necessity of ENET1_REF_CLK1
ARM: dts: imx7s-warp: Use WDOG_B pin reset
...
and Firefly-reload), display support for the rk3288-evb, support for the
recently added firmware reboot-flag support and some housekeeping cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJX0WScAAoJEPOmecmc0R2BEycIAK7/5hV5kyeEA3vx1VaLoRH0
lFHMQyaucbqQCuAu6U6NBwyVGnirvd5HG+KRA34RncLfVT5Fnv81u43byKkaUI/I
8NH6l4FvcND76J1IIR6XZl8cGxaRCT1bkUgII4MFaMaQBxY19gbLCDuBVLVJEhK7
lUy7lG/6j/DvIwU0UevGdB/bdCPZ0WZ6n9InF4xIMJ6PJYI5/BctSpxfJr47hTjQ
a0z637dqXv08L7LRqVtXn+1tJZ6QJdHrtsEavGFOQEzl+n2rRFuBC63+v98h7WCc
1gnyfWbR+NMZOH13imBiOiK7Ap/F5Qm1uF5bfJhoJGbGazv5NcZqPlZ0CocrAXY=
=gktZ
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.9" from Heiko Stübner:
32bit Rockchip devicetree changes containing two new rk3288 boards (Fennec
and Firefly-reload), display support for the rk3288-evb, support for the
recently added firmware reboot-flag support and some housekeeping cleanups.
* tag 'v4.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add sensor-supplies on PopMetal-RK3288 board
ARM: dts: rockchip: fix L3G4200D i2c address on PopMetal-RK3288 board
ARM: dts: rockchip: enable usbotg for Popemtal-rk3288 board
ARM: dts: rockchip: add missing regulators for firefly reload board
ARM: dts: rockchip: remove excess sd properties from firefly reload
ARM: dts: rockchip: add syscon-reboot-mode DT node
soc: rockchip: add reboot-mode header
ARM: dts: rockchip: move rk3288 usbphy under the GRF node
ARM: dts: rockchip: add rk3288-firefly-reload
ARM: dts: rockchip: add dts for RK3288-Fennec boards
ARM: dts: rockchip: add the panel power supply for rk3288-evb board with rk808 pmu
ARM: dts: rockchip: add the panel power supply for rk3288-evb board with act8846 pmu
ARM: dts: rockchip: add eDP/panel display device nodes for rk3288-evb
Business as usual on our side, with a mix of new boards and new IPs enabled
on boards:
- Support for the GPIO found on the AXP PMIC
- ESP8089 on the relevant boards
- More boards converted to the reference design and q8 designs
- New boards: Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange
Pi Lite, Olimex A33-Olinuxino, Empire Electronix M712, inet-d978_rev2,
Nano Pi Neo
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3Q+E
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.9" from Maxime Ripard:
Business as usual on our side, with a mix of new boards and new IPs enabled
on boards:
- Support for the GPIO found on the AXP PMIC
- ESP8089 on the relevant boards
- More boards converted to the reference design and q8 designs
- New boards: Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange
Pi Lite, Olimex A33-Olinuxino, Empire Electronix M712, inet-d978_rev2,
Nano Pi Neo
* tag 'sunxi-dt-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (31 commits)
devicetree: Add vendor prefix for FriendlyARM
ARM: dts: sun8i: Add dts file for the NanoPi NEO SBC
ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers
ARM: dts: sun8i: Add dts file for the Orange Pi Plus2E SBC
ARM: dts: sun8i: Orange Pi Plus dts is for the Plus and Plus 2
ARM: dts: sun8i: Add PWM controller node in H3
ARM: dts: sun8i: Add dts file for inet-d978_rev2 tablets
ARM: dts: sun9i: Add missing #interrupt-cells to R_PIO pinctrl device node
ARM: dts: sun8i: Rename reference-design-tablet touchscreen node
ARM: dts: sun5i: Add dts file for the Empire Electronix M712 tablet
ARM: dts: sun5i: Convert inet-98v-rev2 dts to use reference-design-tablet.dtsi
ARM: dts: sun4i: Disable ohci1 on ba10-tv-box
ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2809
ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2407
ARM: dts: sun8i: add NAND controller node for A23/A33
ARM: dts: sun6i: Add new dts file for tablets using the inet-q972 PCB
ARM: dts: sun6i: Add sun6i-reference-design-tablet.dtsi
ARM: dts: sun6i: colorfly-e708-q1: Remove unused mma8452_int_e708_q1 node
ARM: dts: sun9i: Switch to the AC100 RTC clock outputs for osc32k
ARM: dts: sun9i: cubieboard4: Add device node for AC100
...
- update for Armada XP/38x allowing using direct access SPI
- various improvement for Armada 39x platforms
- add pinctrl information for NANd on Armada 38x
- fix the kirkwood based Openblock A6 external GPIO pins
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfMQ0gACgkQCwYYjhRyO9XZQgCfVtygCoGhhk2ou4huuBcWlutL
It0An1jM4iRF4RwgWtikxEV00Ovg4dJw
=LoDw
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.9-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.9 (part 1)" from Gregory CLEMENT:
- update for Armada XP/38x allowing using direct access SPI
- various improvement for Armada 39x platforms
- add pinctrl information for NANd on Armada 38x
- fix the kirkwood based Openblock A6 external GPIO pins
* tag 'mvebu-dt-4.9-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: fix reference to a390 spi controller
ARM: dts: armada-38x: Add NAND pinctrl information
ARM: dts: kirkwood: Fix Openblock A6 external GPIO pins
ARM: dts: mvebu: armada-395-gp: add support for the Armada 395 GP Board
ARM: dts: mvebu: armada-390-db: add support for the Armada 390 DB board
ARM: dts: mvebu: armada-398-db: enable supported usb interfaces
ARM: dts: mvebu: armada-398: update the dtsi about missing interfaces
ARM: dts: mvebu: armada-395: add support for the Armada 395 SoC family
ARM: dts: mvebu: armada-39x: enable rtc for all Armada-39x SoCs
ARM: dts: mvebu: armada-39x: add missing nodes describing GPIO's
ARM: dts: mvebu: armada-39x: enable watchdog for all Armada-39x SoCs
ARM: dts: mvebu: armada-39x: enable the thermal sensor in Armada-39x SoCs
ARM: dts: mvebu: armada-39x: enable PMU, CA9 SoC Controller and Coherency fabric
ARM: dts: mvebu: armada-39x: update the SDHCI node on Armada 39x
ARM: dts: mvebu: armada-390: add missing compatibility string and bracket
ARM: dts: mvebu: a385-db-ap: add default partition description for NAND
ARM: dts: mvebu: a385-db-ap: enable USB (orion-ehci) port
ARM: dts: mvebu: armada-370-xp: Add MBus mappings for all SPI devices
ARM: dts: mvebu: A37x/XP/38x/39x: Move SPI controller nodes into 'soc' node
ARM: dts: mvebu: Add SPI1 pinctrl defines for Armada XP
Detailed description for this pull request:
1. Support the extcon property and add the synchronization APIs.
- This feature supports the extcon property for external connector
because each external connector might have the property according to
the H/W design.
- The property name should keep the following style.
: EXTCON_PROP_USB_[property_name]
: EXTCON_PROP_CHG_[property_name]
: EXTCON_PROP_JACK_[property_name]
: EXTCON_PROP_DISP_[property_name]
- Add the new extcon APIs to support the extcon property.
: extcon_set_property()
: extcon_get_property()
: extcon_set_property_capability()
: extcon_get_property_capability()
- Add the new synchronization extcon APIs.
: This feature adds the synchronization extcon APIs to support the noti
for both state and property. When extcon_*_sync() functions is called,
the extcon informs the information from extcon provider to extcon client.
The extcon driver may need to change the both state and multiple properties
at the same time. After setting the data of a external connector,
the extcon send the notification to client driver with the extcon_*_sync().
: extcon_sync()
: extcon_set_state_sync()
: extcon_set_property_sync()
- Change the name of existing APIs.
: extcon_set_cable_state_() -> extcon_set_cable()
: extcon_get_cable_state_() -> extcon_get_cable()
2. Add the extcon type to group the connector into five category.
- EXTCON_TYPE_USB : USB connector
- EXTCON_TYPE_CHG : Charger connector
- EXTCON_TYPE_JACK : Jack connector
- EXTCON_TYPE_DISP : Display connector
- EXTCON_TYPE_MISC : Miscellaneous connector
3. Add the new property for external connector.
- EXTCON_PROP_USB_VBUS
- EXTCON_PROP_USB_TYPEC_POLARITY
- EXTCON_PROP_USB_SS (SuperSpeed)
- EXTCON_PROP_DISP_HPD (Hot Plug Detect)
4. Add the new type of external connector.
- EXTCON_DISP_DP : Display Port
- EXTCON_DISP_HMD : Head Mounted Device
- EXTCON_CHG_WPT : Wireless Power Transfer device
5. Add the new extcon driver.
- Qualcomm SPMI PMIC USB id detection driver detects whether
EXTCON_USB_HOST is attached or detached. (extcon-qcom-spmi-mis.c)
6. Remove the usage of extcon_update_state() and old extcon_set_state()
- Both extcon_update_state() and extcon_set_state() should change the state
of all external connectors with bit masking handling. It may occur the
problem. Instead, extcon provides the extcon_set/get_state() functions.
7. Fix the minor issues on extcon drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LF4N
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-testing
Chanwoo writes:
Update extcon for 4.9
Detailed description for this pull request:
1. Support the extcon property and add the synchronization APIs.
- This feature supports the extcon property for external connector
because each external connector might have the property according to
the H/W design.
- The property name should keep the following style.
: EXTCON_PROP_USB_[property_name]
: EXTCON_PROP_CHG_[property_name]
: EXTCON_PROP_JACK_[property_name]
: EXTCON_PROP_DISP_[property_name]
- Add the new extcon APIs to support the extcon property.
: extcon_set_property()
: extcon_get_property()
: extcon_set_property_capability()
: extcon_get_property_capability()
- Add the new synchronization extcon APIs.
: This feature adds the synchronization extcon APIs to support the noti
for both state and property. When extcon_*_sync() functions is called,
the extcon informs the information from extcon provider to extcon client.
The extcon driver may need to change the both state and multiple properties
at the same time. After setting the data of a external connector,
the extcon send the notification to client driver with the extcon_*_sync().
: extcon_sync()
: extcon_set_state_sync()
: extcon_set_property_sync()
- Change the name of existing APIs.
: extcon_set_cable_state_() -> extcon_set_cable()
: extcon_get_cable_state_() -> extcon_get_cable()
2. Add the extcon type to group the connector into five category.
- EXTCON_TYPE_USB : USB connector
- EXTCON_TYPE_CHG : Charger connector
- EXTCON_TYPE_JACK : Jack connector
- EXTCON_TYPE_DISP : Display connector
- EXTCON_TYPE_MISC : Miscellaneous connector
3. Add the new property for external connector.
- EXTCON_PROP_USB_VBUS
- EXTCON_PROP_USB_TYPEC_POLARITY
- EXTCON_PROP_USB_SS (SuperSpeed)
- EXTCON_PROP_DISP_HPD (Hot Plug Detect)
4. Add the new type of external connector.
- EXTCON_DISP_DP : Display Port
- EXTCON_DISP_HMD : Head Mounted Device
- EXTCON_CHG_WPT : Wireless Power Transfer device
5. Add the new extcon driver.
- Qualcomm SPMI PMIC USB id detection driver detects whether
EXTCON_USB_HOST is attached or detached. (extcon-qcom-spmi-mis.c)
6. Remove the usage of extcon_update_state() and old extcon_set_state()
- Both extcon_update_state() and extcon_set_state() should change the state
of all external connectors with bit masking handling. It may occur the
problem. Instead, extcon provides the extcon_set/get_state() functions.
7. Fix the minor issues on extcon drivers.
- Update elm phandle for am335x
- Fix overo NAND gpmc ranges, this has always been broken so it can
wait for the merge window
- Fix NAND and use NAND ready pin for logicpd gpmc, this can wait too
as it's been using the older configration since the dts got added
- A series of dtc warning fixes for unit names
- Keep dcdc3, 5 and 6 enabled during suspend on am347x boards
- Disable DDR regulator during rtc-only/poweroff mode for am437x boards
- Remove redundant regulator compatibles for am437x boards
- Increas QSPI max frequency for dra7 boards
- Enable QSPI for am57xx-idk-common
- Enable am335x-wega audio support
- Workaround for i845 for dra7
- Update binding for logicpd boards
- Add gpio-decoder nodes for am335x-icev2 board
- Add linux,pci-domain property for dra7
- Fix dra7 clock data gmac_gmii_ref_clk_div and related clock tree
entries, these can wait for merge window as Ethernet works on dra7
- A series of changes to drop skeleton.dtsi because of dtc warnings
-----BEGIN PGP SIGNATURE-----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=k+4W
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/dt-pt1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "DTS related changes for omaps for v4.9 merge window" from Tony Lindgren:
- Update elm phandle for am335x
- Fix overo NAND gpmc ranges, this has always been broken so it can
wait for the merge window
- Fix NAND and use NAND ready pin for logicpd gpmc, this can wait too
as it's been using the older configration since the dts got added
- A series of dtc warning fixes for unit names
- Keep dcdc3, 5 and 6 enabled during suspend on am347x boards
- Disable DDR regulator during rtc-only/poweroff mode for am437x boards
- Remove redundant regulator compatibles for am437x boards
- Increas QSPI max frequency for dra7 boards
- Enable QSPI for am57xx-idk-common
- Enable am335x-wega audio support
- Workaround for i845 for dra7
- Update binding for logicpd boards
- Add gpio-decoder nodes for am335x-icev2 board
- Add linux,pci-domain property for dra7
- Fix dra7 clock data gmac_gmii_ref_clk_div and related clock tree
entries, these can wait for merge window as Ethernet works on dra7
- A series of changes to drop skeleton.dtsi because of dtc warnings
* tag 'omap-for-v4.9/dt-pt1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (54 commits)
ARM: dts: dra7: Add missing unit name to memory nodes
ARM: dts: dra62x: Add missing unit name to memory nodes
ARM: dts: dm8168: Add missing unit name to memory nodes
ARM: dts: dm8148: Add missing unit name to memory nodes
ARM: dts: am572x: Add missing unit name to memory nodes
ARM: dts: am4372: Add missing unit name to memory nodes
ARM: dts: am3517: Add missing unit name to memory nodes
ARM: dts: am335x: Add missing unit name to memory nodes
ARM: dts: omap5: Add missing unit name to memory nodes
ARM: dts: omap4: Add missing unit name to memory nodes
ARM: dts: omap3: Add missing unit name to memory nodes
ARM: dts: omap2: Add missing unit name to memory nodes
ARM: dts: am4372: Remove skeleton.dtsi usage
ARM: dts: dra7: Remove skeleton.dtsi usage
ARM: dts: dm816x: Remove skeleton.dtsi usage
ARM: dts: dm814x: Remove skeleton.dtsi usage
ARM: dts: am33xx: Remove skeleton.dtsi usage
ARM: dts: omap5: Remove skeleton.dtsi usage
ARM: dts: omap4: Remove skeleton.dtsi usage
ARM: dts: omap3: Remove skeleton.dtsi usage
...
1. Set chosen serial bitrate which allows proper serial output when
bootloader does pass all the data in command line.
2. Cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Yu8
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "Samsung DeviceTree update for v4.9" from Krzysztof Kozlowski:
1. Set chosen serial bitrate which allows proper serial output when
bootloader does pass all the data in command line.
2. Cleanup.
* tag 'samsung-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use 'hpd-gpios' instead of 'hpd-gpio'
ARM: dts: exynos: Use stdout non-deprecated property and add serial options to Odroid XU/XU3/XU4
This patch adds the basic and regulator bindings for the X-Powers AXP806
PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add necessary compatible flag for Cavium's DWC3 so
dwc3-of-simple will probe.
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some SATA to USB bridges fail to cooperate with some
drives resulting in no cache being present being reported
to the host. That causes the host to skip sending
a command to synchronize caches. That causes data loss
when the drive is powered down.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Qualcomm PMICs have a misc device that performs USB id pin
detection via an interrupt. When the interrupt triggers, we
should read the interrupt line to see if it has gone high or low.
If the interrupt is low then the ID pin is grounded, and if the
interrupt is high then the ID pin is being held high.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
[cw00.choi: Edited the driver description and added the author information]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This tag adds the support of a new SoC to sun4i-drm (the Allwinner A33),
and the usual few fixes and enhancements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=532q
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drm-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into drm-next
Allwinner DRM changes for 4.9
This tag adds the support of a new SoC to sun4i-drm (the Allwinner A33),
and the usual few fixes and enhancements
* tag 'sunxi-drm-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
drm/sun4i: add missing header dependencies
drm/sun4i: Add a DRC driver
drm/sun4i: backend: Handle the SAT
drm/sun4i: support A33 tcon
drm/sun4i: support TCONs without channel 1
drm/sun4i: Clear encoder->bridge if a bridge is not found
drm/sun4i: rgb: add missing calls to drm_panel_{prepare,unprepare}
drm/sun4i: Remove redundant dev_err call in sun4i_tcon_init_regmap()
drm/sun4i: Add bridge support
drm/sun4i: Move panel retrieval in RGB connector
drm/sun4i: Store TCON's device structure pointer
* tag 'topic/drm-misc-2016-09-08' of git://anongit.freedesktop.org/drm-intel:
drm: Fix error path in drm_mode_page_flip_ioctl()
Revert "drm: Unify handling of blob and object properties"
drm/udl: implement usb_driver suspend/resume.
drm: fix signed integer overflow
drm/atomic: Reject properties not part of the object.
drm/doc: Add a few words on validation with IGT
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Synopsys DWC EQoS is a configurable IP block which supports multiple
options for bus type, clocking and reset structure, and feature list.
Extend the DT binding to define a "compatible value" for the configuration
contained in NVIDIA's Tegra186 SoC, and define some new properties and
list property entries required by that configuration.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
In order to support the Oxford Semiconductor OX820 SoC, add new
compatible string to rps timer driver.
Also add new string in the dt-bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The driver has supported touchscreen-fw-name to specify the firmware to
load since it has been merged, but this was omitted from the dt-binding
documentation.
During review of adding touchscreen-fw-name to the binding documentation
it was brought up that there is a standard property name called
"firmware-name" for this, which should be used.
Since there are no users of touchscreen-fw-name yet, this commit
adds documentation of "firmware-name" to the dt-binding documentation
and switches the driver over to use this.
This commit also makes the driver add a "silead/" prefix to the
firmware name from dt before calling request_firmware. That the
firmware files are stored under /lib/firmware/silead under Linux
is an implementation detail and does not belong in devicetree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The power button found in tps65217 device is very similar to the tps65218,
so let's enhance the driver to support both variants.
This driver enables us to use tps65217's power button as KEY_POWER on
am335x boards (directly connected button in chiliboard, accessible pin
via expansion header in beaglebone). This patch has been tested with
chiliboard.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull i2c fixes from Wolfram Sang:
"Mostly driver bugfixes, but also a few cleanups which are nice to have
out of the way"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rk3x: Restore clock settings at resume time
i2c: Spelling s/acknowedge/acknowledge/
i2c: designware: save the preset value of DW_IC_SDA_HOLD
Documentation: i2c: slave-interface: add note for driver development
i2c: mux: demux-pinctrl: run properly with multiple instances
i2c: bcm-kona: fix inconsistent indenting
i2c: rcar: use proper device with dma_mapping_error
i2c: sh_mobile: use proper device with dma_mapping_error
i2c: mux: demux-pinctrl: invalidate properly when switching fails
It is a hardware bug in RK3288, the only way to solve it is to
reset the phy.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds a binding that describes the Rockchip USB Type-C PHY
for rk3399
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 7e472402ca ("phy: omap-usb2: Provide workaround for
USB2PHY false disconnect") added a new binding for USB2 PHYs
on DRA7x. But it has remained undocumented so far.
Add documentation for the binding.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This driver can support for r8a7796 SoC. So, this patch adds it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The clocks property should be set to &cpg, not &mstpX_clks.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds a binding that describes the Rockchip PCIe PHY found
on Rockchip SoCs PCIe interface.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Northstar is a family of SoCs used in home routers. They have USB 2.0
and 3.0 controllers with PHYs that need to be properly initialized.
This driver provides PHY init support in a generic way and can be bound
with XHCI controller driver.
There aren't any public datasheets from Broadcom so we can't have nice
defines for all used bits. It means we just follow Broadcom's
initialization procedure using their magic values. We were quite lucky
actually that Broadcom put some comments in their SDK reference code
explaining what given writes are responsible for.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Update sun4i usb phy dt binding documentation to include support for
Allwinner A64 usb phy.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the clock unit found in the A23. Due to the similarities
with the A33, it also shares its clock IDs to allow sharing the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
This commit introduces the clocks found in the Allwinner A33 CCU.
Since this SoC is very similar to the A23, and we share a significant share
of the DTSI, the clock IDs that are going to be used will also be shared
with the A23, hence the name of the various header files.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
This is a documentation only patch, explaining the
behavior of sched_yield() when a SCHED_DEADLINE
task calls it (give up remaining runtime and be
throttled until next period begins).
Signed-off-by: Tommaso Cucinotta <tommaso.cucinotta@sssup.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juri Lelli <juri.lelli@arm.com>
Reviewed-by: Luca Abeni <luca.abeni@unitn.it>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: Juri Lelli <juri.lelli@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-dl@retis.sssup.it
Link: http://lkml.kernel.org/r/1473443117-11794-2-git-send-email-tommaso.cucinotta@sssup.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- If the PM QoS framework invokes cancel_delayed_work_sync() during
early boot, it will enable interrupts which is not expected at
that point, so prevent it from happening (Tejun Heo).
- Fix cpufreq statistic documentation to follow a recent change in
behavior that forgot to update it as appropriate (Jean Delvare).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=+uoS
-----END PGP SIGNATURE-----
Merge tag 'pm-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"This includes a PM QoS framework fix from Tejun to prevent interrupts
from being enabled unexpectedly during early boot and a cpufreq
documentation fix.
Specifics:
- If the PM QoS framework invokes cancel_delayed_work_sync() during
early boot, it will enable interrupts which is not expected at that
point, so prevent it from happening (Tejun Heo)
- Fix cpufreq statistic documentation to follow a recent change in
behavior that forgot to update it as appropriate (Jean Delvare)"
* tag 'pm-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq-stats: Minor documentation fix
PM / QoS: avoid calling cancel_delayed_work_sync() during early boot
This adds device tree bindings for the TPO TPG110 panel found
mounted in the Nomadik NHK8815.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TPO was a merger on June 5 2006 of Toppoly Optoelectronics and
Philips Mobile Display Systems. They manufactured small and medium
mobile displays.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds code instantiating the EPLL, which is used as the
audio subsystem's root clock.
The requirement to specify the external root clock in clocks property
is documented. Having the consumer 'clocks' property ensures proper
initialization order by explicitly specifying dependencies in DT.
It prevents situations when the SoC's clock controller driver has
initialized, the external oscillator clock is not yet registered
and setting clock frequencies through assigned-clock-rates property
doesn't work properly due to unknown external oscillator frequency.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Exynos5410 Audio Subsystem Clock Controller, comparing to the already
supported IP block revisions, has additionally an I2S_MST divider
so a new compatible string is added.
It is not clear from the Exynos5410 User's Manual released on 2012.03.09
where in the clock tree the I2S_MST clock divider can be found exactly
so this clock is left unimplemented for now.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The power domain must be specified to bring the device out of module
standby. Document this in the bindings provided, so that new additions
are not missed.
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FCP driver can also support the FCPF variant for FDP1 compatible
processing.
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The codes will be called:
MEDIA_BUS_FMT_SBGGR16_1X16
MEDIA_BUS_FMT_SGBRG16_1X16
MEDIA_BUS_FMT_SGRBG16_1X16
MEDIA_BUS_FMT_SRGGB16_1X16
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2_PIX_FMT_SBGGR16 format is documented to contain samples of fewer
than 16 bits. However, we do have specific definitions for smaller sample
sizes. Therefore, this note is redundant from the API point of view.
Currently only two drivers, am437x and davinci, use the
V4L2_PIX_FMT_SBGGR16 pixelformat currently. The sampling precision is
understood to be 16 bits in all current cases.
Remove the note on sampling precision.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The other raw bayer formats had a single sample depth dependent definition
whereas the 8-bit formats had one page for each. Unify the documentation
of the 8-bit formats.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Explicitly state that the most significant n bits are zeroed on 10 and
12 bpp formats.
- Remove extra comma from the last entry of the format list
- Add a missing colon before a list
- Use figures versus word numerals consistently
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The number of high order bits in samples was documented to be 6 for 12-bit
data. This is clearly wrong, fix it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 10-bit packed raw bayer format documented that the data of the first
pixel of a four-pixel group was found in the first byte and the two
highest bits of the fifth byte. This was not entirely correct. The two
bits in the fifth byte are the two lowest bits. The second pixel occupies
the second byte and third and fourth least significant bits and so on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_m2m_dev is opaque: its meaning is only known by
v4l2-mem2mem.c. Ignore it on nitpick mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
One reference there is still using :ref:. Fix it, to solve this
warning:
Documentation/media/uapi/mediactl/media-ioc-g-topology.rst:236: WARNING: undefined label: media-v2-intf-devnode (if the link has no caption the label must precede a section header)
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The struct v4l2_mpeg_vbi_ITV0 is identical to struct v4l2_mpeg_vbi_itv0,
except by its size, and it is documented at the same place at the
book.
Fix cross reference for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several broken references there, due to the conversion to
C domain. Fix them using this shell script and manually adjust what's
broken:
# funcs is a file with the broken functions/references
for i in $(cat funcs|sort|uniq|perl -ne 'print "$1\n" if (m/(\S+)$/)'); do
i=${i//-/_}
echo $i
j=${i//_/-}
for k in $(git grep -l "_$j:" Documentation/); do
sed s,\_$j\:,"c\:type\:\: $i", <$k >a && mv a $k
done
for k in $(git grep -l "$j" Documentation/media/*.exceptions); do
sed s,$j,":c\:type\:\`$i\`", <$k >a && mv a $k
done
for k in $(git grep -l "$j" Documentation/); do
sed "s,:ref:\`$i <$j>\`,:c:type:\`$i\`," <$k >a && mv a $k
sed "s,:ref:\`$j\`,:c:type:\`$i\`," <$k >a && mv a $k
sed -E "s,:ref:\`(.*)<$j>\`,:c:type:\`\1<$i>\`," <$k >a && mv a $k
done
for k in $(git grep -l "<$j>" include/media); do
sed -E "s,:ref:\`(.*)<$j>\`,enum \&$i," <$k >a && mv a $k
done
done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several structs were renamed or removed during V4L2 development.
Don't try to cross-reference the legacy ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use C cross-references to mention the V4L2 API calls on all
places it occurs inside this file.
While here, also mark constants as such.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix those warnings:
Documentation/media/uapi/cec/cec-ioc-dqevent.rst:124: WARNING: c:func reference target not found: clock_gettime(2)
By replacing it with the right function name, using this shell script:
for i in `find Documentation/media -type f`; do sed 's,clock_gettime(2),clock_gettime,' <$i >a && mv a $i; done
Please notice that this will make the nitpick mode to shut up
complaining about that, becasue clock_gettime is on its exclude list,
but the cross reference will be undefined until someone documents
this function at the core documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The :c:type: references point to the structure name, and not to
struct foo.
Fixed via this shell script:
for i in `find Documentation/media -type f`; do perl -ne 'if (s/\:c\:type\:\`struct\s*(\S+)\`/struct :c:type:`$1`/) { s/struct\s+struct/struct/; s/(struct\s+\:c\:type\:\`\S+\`)\s+structure/$1/; } print $_' <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using c:type:`struct foo <foo>`, use:
struct c:type:`foo`
This patch was generated via this shell script:
for i in `find Documentation/media -type f`; do perl -ne 'if (m/\:c\:type\:\`struct\s+(\S+)\s*\<(\S+)\>\`/) { $s=$1; $r=$2; if ($s eq $r) { s/\:c\:type\:\`struct\s+(\S+)\s*\<(\S+)\>\`/struct :c:type:`$2`/; s/struct\s+struct/struct/; s/(struct\s+\:c\:type\:\`\S+\`)\s+structure/$1/; }} print $_' <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivially fix those broken references, by copying the structs
fron the header, just like other API documentation at the
DVB side.
This doesn't have the level of quality used at the V4L2 side
of the API, but, as this documents a deprecated API, used
only by av7110 driver, it doesn't make much sense to invest
time making it better.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several links are broken, as they were using the typedef
name, instead of using the corresponding structs. Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add documentation for struct ca_slot_info and for the two
sets of define used by it, according with what's there at the
ca.h header.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are no descriptions at ca.h header for this struct.
Yet, as we want to get rid of the warnings, let's add a
boilerplate, with just the struct types and fields.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that we moved away from the :ref: type of references,
we need to update the exceptions lists.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are two warnings that are due to functions that has long
gone:
Documentation/media/kapi/v4l2-subdev.rst:417: WARNING: c:func reference target not found: v4l2_i2c_new_subdev_cfg
Documentation/media/kapi/v4l2-subdev.rst:436: WARNING: c:func reference target not found: v4l2_i2c_new_probed_subdev
Update the documentation to remove those.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The "struct" were inside the reference, causing it to break.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several undocumented functions here; document them.
While here, make checkpatch.pl happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the parse-headers.pl and the corresponding files to use
the C domain for enum references.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L version 1 structures had long gone from the Linux Kernel.
It doesn't make sense to use cross-references for them, as they
won't be found.
So, get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
instead of declaring the uAPI structs using usual refs, e. g.:
.. _foo-struct:
Use the C domain way:
.. c:type:: foo_struct
This way, the kAPI documentation can use cross-references to
point to the uAPI symbols.
That solves about ~100 undefined warnings like:
WARNING: c:type reference target not found: foo_struct
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are some functions/macros used by the mediactl documentation
that are alien to the media subsystem. Ignore them.
After this patch, the media core will only complain about this
static function:
Documentation/media/kapi/mc-core.rst:97: WARNING: c:func reference target not found: media_devnode_release
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cross-reference to "struct media_pad" was pointing to
a place that doesn't exist. Fix it, and adjust the second
reference on the same paragraph to use the same text.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of keeping those notes at the file on a non-structured
way, move them to dtv-core.rst, using the proper ReST tags.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There a some other types and functions that aren't declared
inside the media document but are elsewhere. Add them to the
ignore list.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of keep using the normal reference, move to the C
domain ones. Using C domains everywhere will allow
cross-references between kAPI and uAPI docs.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a parser for the --debug option, in order to allow
seeing what the parser is doing.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Aspeed SoC has timer IP with a very similar register layout to the
moxart timer. This patch adds support for the fourth and fifth gen
aspeed SoCs, and has been tested on the ast2400 and ast2500.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
PKRU is the register that lets you disallow writes or all access to a given
protection key.
The XSAVE hardware defines an "init state" of 0 for PKRU: its most
permissive state, allowing access/writes to everything. Since we start off
all new processes with the init state, we start all processes off with the
most permissive possible PKRU.
This is unfortunate. If a thread is clone()'d [1] before a program has
time to set PKRU to a restrictive value, that thread will be able to write
to all data, no matter what pkey is set on it. This weakens any integrity
guarantees that we want pkeys to provide.
To fix this, we define a very restrictive PKRU to override the
XSAVE-provided value when we create a new FPU context. We choose a value
that only allows access to pkey 0, which is as restrictive as we can
practically make it.
This does not cause any practical problems with applications using
protection keys because we require them to specify initial permissions for
each key when it is allocated, which override the restrictive default.
In the end, this ensures that threads which do not know how to manage their
own pkey rights can not do damage to data which is pkey-protected.
I would have thought this was a pretty contrived scenario, except that I
heard a bug report from an MPX user who was creating threads in some very
early code before main(). It may be crazy, but folks evidently _do_ it.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: linux-arch@vger.kernel.org
Cc: Dave Hansen <dave@sr71.net>
Cc: mgorman@techsingularity.net
Cc: arnd@arndb.de
Cc: linux-api@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: luto@kernel.org
Cc: akpm@linux-foundation.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/20160729163021.F3C25D4A@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Allow architectures to create arch/xxx/Makefile.postlink with targets
for vmlinux, modules.ko, and clean, which will be invoked after final
linking of vmlinux and modules.
powerpc will use this to check vmlinux linker relocations for sanity,
and may use it to fix up alternate instruction patch branch addresses.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Add devicetree property for early initialization of the fan controller
to prevent overheating, for example when resetting the board while the
fan was completely turned off.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The fan can be stopped by writing "3" to pwm1_enable in sysfs.
Add devicetree property for early initialization of the fan controller
to prevent overheating, for example when resetting the board while the
fan was completely turned off.
Also improve error reporting, I2C failures were ignored while writing
new values.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds the devicetree binding documentation for the max6650 fan
controller.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The UCD90160 Power Supply Sequencer reuses the existing register layout,
so just an id addition was required.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Ronak Desai <ronak.desai@rockwellcollins.com>
[groeck: Updated description, ordered alphabetically, added documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds hardware temperature and power reading support for
APM X-Gene SoC using the mailbox communication interface.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7470 supports a variety of PWM frequencies. This patch allows the
frequency to be configured and viewed through the sysfs entry pwm1_freq.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add basic pwm attribute support (no auto attributes) to new API.
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Describe the new registration API function as well as the data
structures it requires.
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The cpufreq-stats code can no longer be built as a module, so it now
appears with square brackets in menuconfig.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 1aefc75b24 (cpufreq: stats: Make the stats code non-modular)
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a slightly larger batch of fixes that we've been sitting on a few
-rcs. Most of them are simple oneliners, but there are two sets that are
slightly larger and worth pointing out:
- A set of patches to OMAP to deal with hwmod for RTC on am33xx (beaglebone
SoC, among others). It's the only clock that ever has a valid offset of 0,
so a new flag needed introduction once this problem was discovered.
- A collection of CCI fixes for performance counters discovered once people
started using it on X-Gene CPUs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8pPd
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a slightly larger batch of fixes that we've been sitting on a
few -rcs. Most of them are simple oneliners, but there are two sets
that are slightly larger and worth pointing out:
- A set of patches to OMAP to deal with hwmod for RTC on am33xx
(beaglebone SoC, among others). It's the only clock that ever has
a valid offset of 0, so a new flag needed introduction once this
problem was discovered.
- A collection of CCI fixes for performance counters discovered once
people started using it on X-Gene CPUs"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
arm-cci: pmu: Fix typo in event name
Revert "ARM: tegra: fix erroneous address in dts"
ARM: dts: imx6qdl: Fix SPDIF regression
ARM: imx6: add missing BM_CLPCR_BYPASS_PMIC_READY setting for imx6sx
ARM: dts: imx7d-sdb: fix ti,x-plate-ohms property name
ARM: dts: kirkwood: Fix PCIe label on OpenRD
ARM: kirkwood: ib62x0: fix size of u-boot environment partition
bus: arm-ccn: make event groups reliable
bus: arm-ccn: fix hrtimer registration
bus: arm-ccn: fix PMU interrupt flags
ARM: tegra: Correct polarity for Tegra114 PMIC interrupt
MAINTAINERS: add tree entry for ARM/UniPhier architecture
ARM: sun5i: Fix typo in trip point temperature
MAINTAINERS: Switch to kernel.org account for Krzysztof Kozlowski
ARM: imx6ul: populates platform device at .init_machine
bus: arm-ccn: Add missing event attribute exclusions for host/guest
bus: arm-ccn: Correct required arguments for XP PMU events
bus: arm-ccn: Fix XP watchpoint settings bitmask
bus: arm-ccn: Do not attempt to configure XPs for cycle counter
bus: arm-ccn: Fix PMU handling of MN
...
Make it clear that adding slave support shall not disable master
functionality. We can have both, so we should.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- lazy enablement of runtime instrumentation
- up to 255 CPUs for nested guests
- rework of machine check deliver
- cleanups/fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=99TB
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: features and fixes for 4.9
- lazy enablement of runtime instrumentation
- up to 255 CPUs for nested guests
- rework of machine check deliver
- cleanups/fixes
This adds device tree bindings for the External Bus Interface 2, EBI2
to the Qualcomm SoC drivers.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Inverse Path is an information security consulting company:
https://inversepath.com
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>