Currently we support only PCIe NIC functions zero and one, and FCoE
functions as 3 and 4. Future configurations can mix these up in any
fashion.
This patch removes the 0-1 dependancy and allows usage of any of the 4
functions. We also find the alternate NIC function (if exist) and
determine our port number based on the comparison of the two functions:
Lower function number gets first port, higher function gets second port.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract either manufacturer or Bladecenter Open Fabric
Manager (BOFM) MAC address. BOFM may indicate an
alternate MAC address. This patch honors that request
by extracting the MAC address from a different
flash location if a flag is set.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max frame size register is set higher than the MTU to
accomodate FCoE frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not necessary if hardware supports 65536 as it's the default setting.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware mailbox commands require the firmware to
communicate with the FCoE driver running on another
PCI function. This can potentially take several seconds.
This wait is done in process context only.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 8 banks of 'sub-registers' each of which are accessed
through address/data register pair. An example would be reading
flash or the xgmac. Accessing these require the driver to wait for
a ready bit before writing the address and then accessing the data.
This patch increases the timeout to 100us to prevent timeouts
that have been seen on some platforms.
These register are accessed in process context only.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since an FCoE function shares a port with this NIC function, the
jumbo settings must always be in place. This patch causes the
hardware to be set up for jumbo if it is not already done.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each firmware mailbox command can have a different number of
valid data elements. When waiting for a mailbox command to
complete it the process passes it's element count and
waits for the completion. It is possible that while waiting
an unrelated firmware async event (AE) can arrive. When this
happens, the handler will over write the element count
with the value for the newly arrived AE. This can cause
the mailbox command to not get all of it's data.
This patch restores original mailbox count at the end
of the handler.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check status on every iteration of event handler loop and exit
if an error occurred. If an error occurred then recover process
will be queued so this loop should no continue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused #include <version.h> in drivers/net/qlge/qlge_ethtool.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was introduced in an earlier net-next patch.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The completion interrupt disable routine is only called from the ISR, so
there is no need for irqsave/restore.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of extraneous ql_cycle_adapter. It's only called from the one
place.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware is issuing events to the driver the events
must be removed from the queue. If the queue overflows, the
firmware will build and special event that captures those that
are lost.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This event will arrive at boot time or after an
MPI processor reset if the firmware failed to initialize.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:
1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality to get and set port parameters.
Currently it is used to set maximum TX/RX frame sizes. This process is
also capable of setting:
1) Pause type: Standard or Priority based.
2) Loop back mode.
3) Enable Jumbo frame mode (included here...)
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device has more firmware support for link management, setting
TX and RX maximum frame sizes.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface will be used for setting things like maximum
frame size, setting WOL, and ACKing changes requested by the FCOE
function.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This organizes a few calls into a function table to enable adding new
devices.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not a logical change but rather a move of the inbound firmware event
handler into it's own function as it will later be called by the outbound
path.
The addition of the mutex is to create exclusive access to the mailbox
commands between inbound and outbound handling.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function for performing the reset rather than in-line. This function
may later be called by a core dump process.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer