Add driver for the GPIO block in the ROHM BD9571MWV-W MFD PMIC.
This block is pretty trivial and supports setting GPIO direction
as Input/Output and in case of Output, supports setting value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a simple, generic, single register fixed-direction GPIO driver.
This is able to support a single register with a mixture of inputs
and outputs.
This is different from gpio-mmio and gpio-74xx-mmio:
* gpio-mmio doesn't allow a fixed direction, it assumes there is always
a direction register.
* gpio-74xx-mmio only supports all-in or all-out setups
* gpio-74xx-mmio is DT only, this needs to support legacy too
* they don't double-read when getting the GPIO value, as required by
some implementations that this driver supports
* we need to always do 32-bit reads, which bgpio doesn't guarantee
* the current output state may not be readable from the hardware
register - reading may reflect input status but not output status.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This just deletes the Moxa ART driver and replaces it with the
more versatile Faraday FTGPIO010 driver.
Make this default on for ARCH_GEMINI and ARCH_MOXART so we do
not get Kconfig glitches.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Gemini driver is actually a driver for the Faraday Technology
FTGPIO010 IP block. We rename the driver and the Kconfig symbol and
put in a a new compatible string for the Moxa ART SoC that is also
using this IP block.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES PCI-IDIO-16 device provides 32 lines of digital I/O (16 lines
of optically-isolated digital inputs for AC and DC control signals, and
16 lines of solid state switch digital outputs). An interrupt is
generated when any of the inputs change state (low to high or high to
low). Input filter control is not supported by this driver, and input
filters are deactivated by this driver.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Exar XR17V352/354/358 chips have 16 multi-purpose inputs/outputs which
can be controlled using gpio interface.
Add the gpio specific code.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a heavy edit/rewrite of the GPIO driver for the Gemini
SoC from arch/arm/mach-gemini/gpio.c.
This rewrite uses all the best-in-class helper like generic
GPIO and GPIOLIB_IRQCHIP and has been tested on ITian Square One
Gemini-based NAS/router.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Simplify threaded interrupt handling: instead of passing
numbed parameters to gpiochip_irqchip_add_chained() we
create a new call: gpiochip_irqchip_add_nested() so the two
types are clearly semantically different. Also make sure
that all nested chips call gpiochip_set_nested_irqchip()
which is necessary for IRQ resend to work properly if
it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so
that anything != 0 will be send down to the driver as "1"
not the value passed in.
- ACPI can now support naming of GPIO lines, hogs and holes
in the GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem
and was moved over to a combined GPIO+pinctrl driver in the
pinctrl subsystem.
New features:
- Various cleanups to various drivers.
-----BEGIN PGP SIGNATURE-----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=2UpT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Luinus Walleij:
"Bulk GPIO changes for the v4.10 kernel cycle:
Core changes:
- Simplify threaded interrupt handling: instead of passing numbed
parameters to gpiochip_irqchip_add_chained() we create a new call:
gpiochip_irqchip_add_nested() so the two types are clearly
semantically different. Also make sure that all nested chips call
gpiochip_set_nested_irqchip() which is necessary for IRQ resend to
work properly if it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so that
anything != 0 will be send down to the driver as "1" not the value
passed in.
- ACPI can now support naming of GPIO lines, hogs and holes in the
GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem and was
moved over to a combined GPIO+pinctrl driver in the pinctrl
subsystem.
New features:
- Various cleanups to various drivers"
* tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits)
gpio: merrifield: Implement gpio_get_direction callback
gpio: merrifield: Add support for hardware debouncer
gpio: chardev: Return error for seek operations
gpio: arizona: Tidy up probe error path
gpio: arizona: Remove pointless set of platform drvdata
gpio: pl061: delete platform data handling
gpio: pl061: move platform data into driver
gpio: pl061: rename variable from chip to pl061
gpio: pl061: rename state container struct
gpio: pl061: use local state for parent IRQ storage
gpio: set explicit nesting on drivers
gpio: simplify adding threaded interrupts
gpio: vf610: use builtin_platform_driver
gpio: axp209: use correct register for GPIO input status
gpio: stmpe: fix interrupt handling bug
gpio: em: depnd on ARCH_SHMOBILE
gpio: zx: depend on ARCH_ZX
gpio: x86: update config dependencies for x86 specific hardware
gpio: mb86s7x: use builtin_platform_driver
gpio: etraxfs: use builtin_platform_driver
...
This option was added in 6a89a314ab to
allow use of the devm_gpio_* functions without CONFIG_GPIOLIB.
However, only a few months later in
b69ac52449, CONFIG_GPIOLIB was added
as a dependency, defeating the original purpose of this option.
Instead of that patch, the original commit could have just been
reverted (and in fact was partially so in
403c1d0be5). Further, since this
option has a dependency on HAS_IOMEM, even though it does not
require it, it causes build failures when !HAS_IOMEM (e.g. in a
uml build).
Fix that by completely removing the option, in essence completing
the reversion of the original commit.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to use "gpio-line-names" property in systems not having DT as
their boot firmware, rework of_gpiochip_set_names() to use device property
accessors. This reworked function is placed in a separate file making it
clear it deals with universal device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the GPIO functionality for the Altera Arria10 MAX5 System Resource
Chip. The A10 MAX5 has 12 bits of GPIO assigned to switches, buttons,
and LEDs as a GPIO extender on the SPI bus.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>i
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The HTC GPIO driver is a pure GPIO driver and I just can not
see what it is doing inside MFD. Let's just move it to GPIO
and take this opportunity to move the platform data to
<linux/platform_data/gpio-htc-egpio.h>
Cc: arm@kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add basic structure of a virtual gpio device(gpio-mockup)
for testing gpio subsystem. The tester could manipulate such device
through userspace(sysfs or char device) and check the result from
debugfs.
Currently, it support one or more gpiochip(determined by module
parameters with base,ngpio pair). One could test the overlap of
different gpiochip and test the direction and/or output values of
these chips.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed SoCs contain GPIOs banked by letter, where each bank contains
8 pins. The GPIO banks are then grouped in sets of four in the register
layout.
The implementation exposes multiple banks through the one driver and
requests and releases pins via the pinctrl subsystem. The hardware
supports generation of interrupts from all GPIO-capable pins.
A number of hardware features are not yet supported: Configuration of
interrupt direction (ARM or LPC), debouncing, and WDT reset tolerance
for output ports.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for lp873x PMIC family GPOs. Two GPOs are supported
and can be configured in Open-drain output or Push-pull output.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver is generic and aims to support all Technologic Systems's
boards embedding FPGA GPIOs with an I2C interface.
This driver supports TS-4900, TS-7970, TS-7990 and TS-4100 series.
Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Diamond Systems GPIO-MM device features 48 lines of digital I/O via
the emulation of dual 82C55A PPI chips. This driver provides GPIO
support for these 48 channels of digital I/O. The base port addresses
for the devices may be configured via the base array module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch introduces a separate GPIO driver for Intel WhiskeyCove PMIC.
This driver is based on gpio-crystalcove.c.
Changes in v7:
- Fixed various coding style comments from Andy Shevchenko
Changes in v6:
- Removed unnecessary wcove_gpio_remove()
- Used devm_gpiochip_remove() instead of gpiochip_remove()
- Various coding style changes per Mika's comment
Changes in v5:
- Revisited the interrupt handler code to iterate until all pending
interrupts are handled. This change is to avoid missing interrupt
when we're inside the interrupt handler.
- Used regmap_bulk_read() to read address adjacent registers.
Changes in v4:
- Converted CTLI_INTCNT_XX macros to less verbose ones INT_DETECT_XX.
- Add comments about why there is no .pm for the driver.
- Header files re-ordered.
- Various coding style change to address Andy's comments.
Changes in v3:
- Fixed the year in copyright line(2015-->2016).
- Removed DRV_NAME macro.
- Added kernel-doc for regmap_irq_chip of the wcove_gpio structure.
- Line length fix.
Changes in v2:
- Typo fix (Whsikey --> Whiskey).
- Included linux/gpio/driver.h instead of linux/gpio.h
- Implemented .set_single_ended().
- Added GPIO register description.
- Replaced container_of() with gpiochip_get_data().
- Removed unnecessary "if (gpio > WCOVE_VGPIO_NUM" check.
- Removed the device id table and added MODULE_ALIAS().
Signed-off-by: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Signed-off-by: Bin Gao <bin.gao@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AXP209 PMIC has a bunch of GPIOs accessible, that are usually used to
control LEDs or backlight.
Add a driver for them
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Merrifield platform has a special GPIO controller to
drive pads when they are muxed in corresponding mode.
Intel Merrifield GPIO IP is slightly different here and there
in comparison to the older Intel MID platforms. These differences
include in particular the shaked register offsets, specific
support of level triggered interrupts and wake capable sources,
as well as a pinctrl which is a separate IP.
Instead of uglifying existing driver I decide to provide a new
one slightly based on gpio-intel-mid.c. So, anyone can easily
compare what changes are happened to be here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Brian J Wood <brian.j.wood@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MAXIM Semiconductor's PMIC, MAX77620/MAX20024 has 8 GPIO
pins. It also supports interrupts from these pins.
Add GPIO driver for these pins to control via GPIO APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch renames the gpio-generic.c into gpio-mmio.c.
This is because currently the file only contains code
for a memory-mapped GPIO driver. There isn't any support
for ioports or other resource type.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow compile testing this driver by adding a new config option which
is enabled by default and depends on the old symbol or COMPILE_TEST.
Signed-off-by: Alexander Stein <alexanders83@web.de>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Add support for the TPS65086 PMIC GPOs.
TPS65086 has four configurable GPOs that can be used for several
purposes. These are output only.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The 16Z127 is a 32bit GPIO controller on a MCB FPGA.
Every single line can be configured as input and output.
Push pull and open drain are supported as well as setting
a debounce value for the input lines.
Signed-off-by: Andreas Werner <andy@wernerandy.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for the GPIO block found in ti's tps65218 pmics.
The device has two GPIOs and one GPO pin which can be configured as follows:
GPIO1:
-general-purpose, open-drain output controlled by GPO1 user bit and/or
sequencer
-DDR3 reset input signal from SOC. Signal is either latched or
passed-trough to GPO2 pin. See below for details.
GPO2:
-general-purpose output controlled by GPO2 user bit
-DDR3 reset output signal. Signal is controlled by GPIO1 and PGOOD.
See below for details.
-Output buffer can be configured as open-drain or push-pull.
GPIO3:
-general-purpose, open-drain output controlled by GPO3 user bit and/or
sequencer
-reset input-signal for DCDC1 and DCDC2.
The input configurations are not meant to be used by the user so the driver
only offers GPOs.
v2: Added request routine that evaluates the fw config flags and removed module
owner
v3: Added .direction_input() routine, and took care of all Linus Walleij
suggestions (clamp to bool, use proper include)
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for TI TPIC2810 8-Bit LED Driver with I2C Interface.
The TPIC2810 has 8 open-drain outputs that can but used to drive
LEDs and other low-side switched resistive loads.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add generic parallel-in/serial-out shift register GPIO driver.
This includes SPI compatible devices like SN74165 serial-out shift
registers and the SN65HVS88x series of industrial serializers that can
be read over the SPI bus and used for GPI (General Purpose Input).
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop most of the code in favor of the generic MMIO GPIO driver.
As the driver now depend on CONFIG_GPIO_GENERIC also add a Kconfig
entry to make the driver optional.
We leave the base pointer and lock in the data struct because they are
needed for the IRQ support.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TS-4800 GPIO driver provide support for the GPIOs available
on the Technologic Sytems board FPGA. It allows to set
direction and read/write states.
It uses the generic gpio driver.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-DIO-48E device provides 48 lines digital I/O via two
Programmable Peripheral Interface (PPI) chips of type 82C55. Bit C3 at
each 24-bit Group can be used as an external interrupt, triggered by a
rising edge.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the dio_48e_base module parameter. The interrupt line number for the
device may be configured via the dio_48e_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WinSystems WS16C48 device provides 48 lines of digital I/O. In
addition, the first 24 lines may be used for interrupt-handled edge
detection; rising edge detection and falling edge detection are
supported.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the ws16c48_base module parameter. The interrupt line number for the
device may be configured via the ws16c48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
The gpio-samsung driver is special in the sense that it
interacts directly in multiple ways with the legacy platform
code for the s3c24xx and s3c64xx platforms. In contrast,
all devicetree based machines for Samsung, including the
ones on those two SoC families use a different driver.
The header files that define the interface between the platform
code and the gpio driver are not visible when building a
kernel for ARCH_MULTIPLATFORM, which prevents us from
turning on this option for s3c64xx.
To work around this, we now move the driver back into platform
code, from where it was originally moved to as part of commit
1b39d5f2cc ("gpio/samsung: gpio-samsung.c to support
Samsung GPIOs").
The long-term plan for this driver would be to remove it
entirely, after all Samsung machines have been converted
over to boot from DT, but there is currently no timeline
for when that might happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The ACCES 104-IDI-48 family of PC/104 utility boards feature 48
individually optically isolated digital inputs. Enabled inputs feature
change-of-state detection capability; if change-of-state detection is
enabled, an interrupt is fired off if a change of input level
(low-to-high or high-to-low) is detected. Change-of-state IRQs are
enabled/disabled on 8-bit boundaries, for a total of six boundaries.
This driver provides GPIO and IRQ support for these 48 channels of
digital input. The base port address for the device may be configured
via the idi_48_base module parameter. The interrupt line number for the
device may be configured via the idi_48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 family of PC/104 utility boards feature 16
optically isolated inputs and 16 optically isolated FET solid state
outputs. This driver provides GPIO support for these 32 channels of
digital I/O. Change-of-State detection interrupts are not supported.
GPIO 0-15 correspond to digital outputs 0-15, while GPIO 16-31
correspond to digital inputs 0-15. The base port address for the device
may be set via the idio_16_base module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the GPIOs found on the ITE super-I/O chips
IT87xx.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove this driver now that Bjorn has introduced a pinctrl driver
for msm8660 and the dts files have been updated with the pinctrl
compatibles.
Cc: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV52lvAAoJEEEQszewGV1zOVcP/2ZgkfRgl119LZnWShfrEJWq
UXaNzSaPNgvDzvGaqqi62SZQuhrdIWRKfMPtAuMGbEn5aJx0JC5UAOYjjfkKBqpO
toqc1w2DScc0JTorY8qgczIBDO1A3ZBAcIvXXpOduy/JaKPoQteRN8WYTynPw48/
0+97ZODwhyOkfeqmvUClkc9gW4XT68dudb0Lv1nQjsZmd1dHF2PZlwH3aL9sV68j
GJAqf09xNqZaWWQBhs+J3ptsYjaJfYjo9NOOUf0Y/UgqXO3vB+2S4EmRATaRHS2F
aHdj03sNZCNSDEa35WwetbLRGxPzSWmfxmBzQQ1baGdcJICn7Yv58EklPKRvwtMo
ZpUsgiOV4OUIEClPJohs4xbl2HRsOYB3VbcihkXjVAxS6i2/jgA3Tn8ATvUSZ8wq
TX8D6BfciigRCkT2G+B0TQBmcX1IQsMd1DBUNfw7Dk1TK/vxH4UYWbke422RjKGz
ORJ+0DfShMCdYjrCVlt7UbFcqE3L5CnrztLQ3oFt0om2JsSWztV9V579G+Dqo9CI
fE4G3xlsF33UCvXcmnOp6PuU+ZYBodLggkmK4REy2D3LCOnkcKq0U8Fj5RssApZ9
FdqVYck555ZpcBiN8ihB97WsmU+0XhBjblCbgzr6GxUw8EJ4x8H9nlraA6bluFoP
9c2qgPxjCq/VWA/F0YOU
=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
Add a GPIO driver for the General I/O block on Axis ETRAX FS SoCs.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the GPIO IP "UPG GIO" used on
Broadcom STB SoCs (BCM7XXX and some others). Uses
basic_mmio_gpio to instantiate a gpio_chip for each bank.
The driver assumes that it handles the base set of GPIOs
on the system and that it can start its numbering sequence
from 0, so any GPIO expanders used with it must dynamically
assign GPIO numbers after this driver has finished
registering its GPIOs.
Does not implement the interrupt-controller portion yet,
will be done in a future commit.
v2:
- change include to use <linux/gpio/driver.h> instead of
<linux/gpio.h>
- get rid of unnecessary imask member in struct bank
- rename GPIO_PER_BANK -> MAX_GPIO_PER_BANK
- always have 32 GPIOs per bank and add 'width' member in
struct bank to hold actual number of GPIOs in use
- mark of_match table as const
List-usage-fixed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Marek Vasut