This reverts commit 89b593c30e ("ALSA: usb-audio: purge needless
variable length array"). The patch turned out to cause a severe
regression, triggering an Oops at snd_usb_ctl_msg(). It was overseen
that snd_usb_ctl_msg() writes back the response to the given buffer,
while the patch changed it to a read-only const buffer. (One should
always double-check when an extra pointer cast is present...)
As a simple fix, just revert the affected commit. It was merely a
cleanup. Although it brings VLA again, it's clearer as a fix. We'll
address the VLA later in another patch.
Fixes: 89b593c30e ("ALSA: usb-audio: purge needless variable length array")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195875
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Force vop output mode on encoder driver seem not a good idea,
EDP, HDMI, DisplayPort all have 10bit input on rk3399,
On non-10bit vop, vop 8bit output bit[0-7] connect to the
encoder high 8bit [2-9].
So force RGB10 to RGB888 on vop driver would be better.
And another problem, EDP check crtc id on atomic_check,
but encoder maybe NULL, so out_mode configure would fail,
it cause edp no display.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495885416-22216-1-git-send-email-mark.yao@rock-chips.com
When the controller fails to provide an RPM reading within the alloted
time; the driver returns -ETIMEDOUT and no file contents.
Signed-off-by: Patrick Venture <venture@google.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver uses regmap and thus has to select it to avoid build
errors such as the following.
drivers/hwmon/aspeed-pwm-tacho.c:337:21: error: variable
'aspeed_pwm_tacho_regmap_config' has initializer but incomplete type
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This effectively reverts commit 8ee74a91ac ("proc: try to remove use
of FOLL_FORCE entirely")
It turns out that people do depend on FOLL_FORCE for the /proc/<pid>/mem
case, and we're talking not just debuggers. Talking to the affected people, the use-cases are:
Keno Fischer:
"We used these semantics as a hardening mechanism in the julia JIT. By
opening /proc/self/mem and using these semantics, we could avoid
needing RWX pages, or a dual mapping approach. We do have fallbacks to
these other methods (though getting EIO here actually causes an assert
in released versions - we'll updated that to make sure to take the
fall back in that case).
Nevertheless the /proc/self/mem approach was our favored approach
because it a) Required an attacker to be able to execute syscalls
which is a taller order than getting memory write and b) didn't double
the virtual address space requirements (as a dual mapping approach
would).
I think in general this feature is very useful for anybody who needs
to precisely control the execution of some other process. Various
debuggers (gdb/lldb/rr) certainly fall into that category, but there's
another class of such processes (wine, various emulators) which may
want to do that kind of thing.
Now, I suspect most of these will have the other process under ptrace
control, so maybe allowing (same_mm || ptraced) would be ok, but at
least for the sandbox/remote-jit use case, it would be perfectly
reasonable to not have the jit server be a ptracer"
Robert O'Callahan:
"We write to readonly code and data mappings via /proc/.../mem in lots
of different situations, particularly when we're adjusting program
state during replay to match the recorded execution.
Like Julia, we can add workarounds, but they could be expensive."
so not only do people use FOLL_FORCE for both reads and writes, but they
use it for both the local mm and remote mm.
With these comments in mind, we likely also cannot add the "are we
actively ptracing" check either, so this keeps the new code organization
and does not do a real revert that would add back the original comment
about "Maybe we should limit FOLL_FORCE to actual ptrace users?"
Reported-by: Keno Fischer <keno@juliacomputing.com>
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tagset lock needs to be held when iterating the tag_list, so a
lockdep assert was added when updating number of hardware queues. The
drivers calling this API, however, were unaware of the new requirement,
so are failing the assertion.
This patch takes the lock within the blk-mq function so the drivers do
not have to be modified in order to be safe.
Fixes: 705cda97e ("blk-mq: Make it safe to use RCU to iterate over blk_mq_tag_set.tag_list")
Reported-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Tariq Toukan says:
====================
MAINTAINERS updates
This patchset contains updates to the MAINTAINERS file.
In the first patch, I replace Yishai as the maintainer of
the mlx4_core driver.
In the other two patches we move an RDMA header file from
the list of the mlx4/mlx5 core driver into the respective
IB driver, where it belongs.
Series generated against net commit:
468b0df61a Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It belongs there, should not be under mlx5 Core driver.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It belongs there, should not be under mlx4 Core driver.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add myself as a maintainer for mlx4 core driver,
replacing Yishai Hadas.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building the driver with CONFIG_SMP disabled results in a harmless
warning:
ethernet/mellanox/mlx5/core/main.c: In function 'mlx5_irq_set_affinity_hint':
ethernet/mellanox/mlx5/core/main.c:615:6: error: unused variable 'irq' [-Werror=unused-variable]
It's better to express the conditional compilation using IS_ENABLED()
here, as that lets the compiler see what the intented use for the variable
is, and that it can be silently discarded.
Fixes: b665d98edc ("net/mlx5: Tolerate irq_set_affinity_hint() failures")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'static' was not enough, the helpers must be 'static inline'
net/dsa/mv88e6xxx/global2.h:123:12: error: 'mv88e6xxx_g2_misc_4_bit_port' defined but not used [-Werror=unused-function]
net/dsa/mv88e6xxx/global2.h:117:12: error: 'mv88e6xxx_g2_pvt_write' defined but not used [-Werror=unused-function]
Fixes: c21fbe29f8 ("net: dsa: mv88e6xxx: Add missing static to stub functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation lacks the logic for providing management
firmware with RDMA-related statistics; [much] worse than that -
it logs such events by default to system logs.
Since the statistics' gathering is done periodically, using sufficiently
new management firmware the system logs would get filled with these
unnecessary prints.
For now, reduce the verbosity of the log so that it would not be
logged by default.
Fixes: 6c75424612 ("qed: Add support for NCSI statistics")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PCI error recovery process, specifically on eeh_err_detected()
we might have a NULL netdev struct, hence a direct dereference will
lead to a kernel oops. This was observed with latest upstream kernel
(v4.12-rc2) on Chelsio adapter T422-CR in PowerPC machines.
This patch checks for NULL pointer and avoids the crash, both in
eeh_err_detected() and eeh_resume(). Also, we avoid to trigger
a fatal error or to try disabling interrupts on FW during PCI
error recovery, because: (a) driver might not be able to accurately
access PCI regions in this case, and (b) trigger a fatal error
_during_ the recovery steps is a mistake that could prevent the
recovery path to complete successfully.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 19bca6ab75 ("KVM: SVM: Fix cross vendor migration issue with
unusable bit") added checking type when setting unusable.
So unusable can be set if present is 0 OR type is 0.
According to the AMD processor manual, long mode ignores the type value
in segment descriptor. And type can be 0 if it is read-only data segment.
Therefore type value is not related to unusable flag.
This patch is based on linux-next v4.12.0-rc3.
Signed-off-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_skip_emulated_instruction() will return 0 if userspace is
single-stepping the guest.
kvm_skip_emulated_instruction() uses return status convention of exit
handler: 0 means "exit to userspace" and 1 means "continue vm entries".
The problem is that nested_vmx_check_vmptr() return status means
something else: 0 is ok, 1 is error.
This means we would continue executing after a failure. Static checker
noticed it because vmptr was not initialized.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 6affcbedca ("KVM: x86: Add kvm_skip_emulated_instruction and use it.")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
nbd_config is allocated in nbd_alloc_config(), but never freed.
Fixes: 5ea8d10802 ("nbd: separate out the config information")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is nothing to clear -- nbd_device has just been allocated.
Fold nbd_reset() into its other caller, nbd_config_put().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We saw perf IRQ init failures when running Linux kernel in an ACPI
guest without PMU (i.e. pmu=off). This is because perf IRQ is not
present when pmu=off, but arm_pmu_acpi still tries to register
or unregister GSI. This patch addresses the problem by checking
gicc->performance_interrupt. If it is 0, which is the value set
by qemu when pmu=off, we skip the IRQ register/unregister process.
[ 4.069470] bc00: 0000000000040b00 ffff0000089db190
[ 4.070267] [<ffff000008134f80>] enable_percpu_irq+0xdc/0xe4
[ 4.071192] [<ffff000008667cc4>] arm_perf_starting_cpu+0x108/0x10c
[ 4.072200] [<ffff0000080cbdd4>] cpuhp_invoke_callback+0x14c/0x4ac
[ 4.073210] [<ffff0000080ccd3c>] cpuhp_thread_fun+0xd4/0x11c
[ 4.074132] [<ffff0000080f1394>] smpboot_thread_fn+0x1b4/0x1c4
[ 4.075081] [<ffff0000080ec90c>] kthread+0x10c/0x138
[ 4.075921] [<ffff0000080833c0>] ret_from_fork+0x10/0x50
[ 4.076947] genirq: Setting trigger mode 4 for irq 43 failed
(gic_set_type+0x0/0x74)
Signed-off-by: Wei Huang <wei@redhat.com>
[will: add comment justifying deviation from ACPI spec, removed redundant hunk]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add device-tree files relevant to TI DaVinci platform
to its entry so mach-davinci sub-arch maintainers get
copied on patches with device-tree file updates.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
arch_teardown_dma_ops() being the inverse of arch_setup_dma_ops()
,dma_ops should be cleared in the teardown path. Currently, only the
device's iommu mapping structures are cleared in arch_teardown_dma_ops,
but not the dma_ops. So on the next reprobe, dma_ops left in place is
stale from the first IOMMU setup, but iommu mappings has been disposed
of. This is a problem when the probe of the device is deferred and
recalled with the IOMMU probe deferral.
So for fixing this, slightly refactor by moving the code from
__arm_iommu_detach_device to arm_iommu_detach_device and cleanup
the former. This takes care of resetting the dma_ops in the teardown
path.
Fixes: 09515ef5dd ("of/acpi: Configure dma operations at probe time for platform/amba/pci bus devices")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
With IOMMU probe deferral, iort_iommu_configure can be called
multiple times for the same device. Hence we have a check
to see if the device's fwspec is already translated and return
the iommu_ops from that directly. But the check is wrongly
placed in iort_iommu_xlate, which breaks devices with multiple
sids. Move the check to iort_iommu_configure.
Fixes: 5a1bb638d5 ("drivers: acpi: Handle IOMMU lookup failure with deferred probing or error")
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
arch_setup_dma_ops() is used in device probe code paths to create an
IOMMU mapping and attach it to the device. The function assumes that the
device is attached to a device-specific IOMMU instance (or at least a
device-specific TLB in a shared IOMMU instance) and thus creates a
separate mapping for every device.
On several systems (Renesas R-Car Gen2 being one of them), that
assumption is not true, and IOMMU mappings must be shared between
multiple devices. In those cases the IOMMU driver knows better than the
generic ARM dma-mapping layer and attaches mapping to devices manually
with arm_iommu_attach_device(), which sets the DMA ops for the device.
The arch_setup_dma_ops() function takes this into account and bails out
immediately if the device already has DMA ops assigned. However, the
corresponding arch_teardown_dma_ops() function, called from driver
unbind code paths (including probe deferral), will tear the mapping down
regardless of who created it. When the device is reprobed
arch_setup_dma_ops() will be called again but won't perform any
operation as the DMA ops will still be set.
We need to reset the DMA ops in arch_teardown_dma_ops() to fix this.
However, we can't do so unconditionally, as then a new mapping would be
created by arch_setup_dma_ops() when the device is reprobed, regardless
of whether the device needs to share a mapping or not. We must thus keep
track of whether arch_setup_dma_ops() created the mapping, and only in
that case tear it down in arch_teardown_dma_ops().
Keep track of that information in the dev_archdata structure. As the
structure is embedded in all instances of struct device let's not grow
it, but turn the existing dma_coherent bool field into a bitfield that
can be used for other purposes.
Fixes: 09515ef5dd ("of/acpi: Configure dma operations at probe time for platform/amba/pci bus devices")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
While deferring the probe of IOMMU masters, xlate and
add_device callbacks called from iort_iommu_configure
can pass back error values like -ENODEV, which means
the IOMMU cannot be connected with that master for real
reasons. Before the IOMMU probe deferral, all such errors
were ignored. Now all those errors are propagated back,
killing the master's probe for such errors. Instead ignore
all the errors except EPROBE_DEFER, which is the only one
of concern and let the master work without IOMMU, thus
restoring the old behavior. Also make explicit that
acpi_dma_configure handles only -EPROBE_DEFER from
iort_iommu_configure.
Fixes: 5a1bb638d5 ("drivers: acpi: Handle IOMMU lookup failure with deferred probing or error")
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
While deferring the probe of IOMMU masters, xlate and
add_device callbacks called from of_iommu_configure
can pass back error values like -ENODEV, which means
the IOMMU cannot be connected with that master for real
reasons. Before the IOMMU probe deferral, all such errors
were ignored. Now all those errors are propagated back,
killing the master's probe for such errors. Instead ignore
all the errors except EPROBE_DEFER, which is the only one
of concern and let the master work without IOMMU, thus
restoring the old behavior. Also make explicit that
of_dma_configure handles only -EPROBE_DEFER from
of_iommu_configure.
Fixes: 7b07cbefb6 ("iommu: of: Handle IOMMU lookup failure with deferred probing or error")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Magnus Damn <magnus.damn@gmail.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Now with IOMMU probe deferral, we return -EPROBE_DEFER
for masters that are connected to an IOMMU which is not
probed yet, but going to get probed, so that we can attach
the correct dma_ops. So while trying to defer the probe of
the master, check if the of_iommu node that it is connected
to is marked in DT as 'status=disabled', then the IOMMU is never
is going to get probed. So simply return NULL and let the master
work without an IOMMU.
Fixes: 7b07cbefb6 ("iommu: of: Handle IOMMU lookup failure with deferred probing or error")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Magnus Damn <magnus.damn@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Newly added code in the ipmmu-vmsa driver showed a small mistake
in a header file that can't be included by itself without CONFIG_IOMMU_DMA
enabled:
In file included from drivers/iommu/ipmmu-vmsa.c:13:0:
include/linux/dma-iommu.h:105:94: error: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
This adds a forward declaration for 'struct device', similar to how
we treat the other struct types in this case.
Fixes: 3ae4729202 ("iommu/ipmmu-vmsa: Add new IOMMU_DOMAIN_DMA ops")
Fixes: 273df96353 ("iommu/dma: Make PCI window reservation generic")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When starting or stopping an aggregation session, one of the steps
is that the driver calls back to mac80211 that the start/stop can
proceed. This is handled by queueing up a fake SKB and processing
it from the normal iface/sdata work. Since this isn't flushed when
disassociating, the following race is possible:
* associate
* start aggregation session
* driver callback
* disassociate
* associate again to the same AP
* callback processing runs, leading to a WARN_ON() that
the TID hadn't requested aggregation
If the second association isn't to the same AP, there would only
be a message printed ("Could not find station: <addr>"), but the
same race could happen.
Fix this by not going the whole detour with a fake SKB etc. but
simply looking up the aggregation session in the driver callback,
marking it with a START_CB/STOP_CB bit and then scheduling the
regular aggregation work that will now process these bits as well.
This also simplifies the code and gets rid of the whole problem
with allocation failures of said skb, which could have left the
session in limbo.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In descriptor mode, the descriptor running pointer is not maintained
by the interrupt handler, thus, driver finds the running descriptor
from the descriptor pointer field in the CHCRB register.
But, CHCRB::DPTR indicates *next* descriptor pointer, not current.
Thus, The residue calculation will be missed. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Conntrack SCTP CRC32c checksum mangling may operate on non-linear
skbuff, patch from Davide Caratti.
2) nf_tables rb-tree set backend does not handle element re-addition
after deletion in the same transaction, leading to infinite loop.
3) Atomically unclear the IPS_SRC_NAT_DONE_BIT on nat module removal,
from Liping Zhang.
4) Conntrack hashtable resizing while ctnetlink dump is progress leads
to a dead reference to released objects in the lists, also from
Liping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Users should really consider switching to rmi-smbus instead of plain PS/2.
Notify them that they should report a missing pnpID in the file.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Synaptics touchpads are now either using i2c-hid or rmi-smbus.
Warn the users if they are missing the rmi-smbus modules and have no
chance of reporting correct data.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Or the user might have the touchpad unbound from PS/2 but never picked
up by rmi-smbus.ko
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
synaptics_query_hardware() was being passed a 'struct synaptics_device_info'
in uninitialized stack memory, then not always initializing all fields.
This caused garbage to show up in certain fields, making the touchpad
unusable.
Fix by zeroing the device info, so all fields default to 0.
Fixes: 6c53694fb2 ("Input: synaptics - split device info into a separate structure")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When we put the touchscreen controller in low-power mode the irq
pin may trigger (float) and if we then try to read a data packet we
get the following error in dmesg:
[ 478.801017] silead_ts i2c-MSSL1680:00: Data read error -121
This commit disables the irq during suspend/resume fixing this error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For a driver that does not set the CPUFREQ_STICKY flag, if all of the
->init() calls fail, cpufreq_register_driver() should return an error.
This will prevent the driver from loading.
Fixes: ce1bcfe94d (cpufreq: check cpufreq_policy_list instead of scanning policies for all CPUs)
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Signed-off-by: David Arcari <darcari@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the Linux kernel, acpi_get_table() "clones" haven't been fully
balanced by acpi_put_table() invocations. In upstream ACPICA, due to
the design change, there are also unbalanced acpi_get_table_by_index()
invocations requiring special care.
acpi_get_table() reference counting mismatches may occor due to that
and printing error messages related to them is not useful at this
point. The strict balanced validation count check should only be
enabled after confirming that all invocations are safe and aligned
with their designed purposes.
Thus this patch removes the error value returned by acpi_tb_get_table()
in that case along with the accompanying error message to fix the
issue.
Fixes: 174cc7187e (ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel)
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Reported-by: Anush Seetharaman <anush.seetharaman@intel.com>
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 77e9a4aa9d (ACPI / button: Change default behavior to
lid_init_state=open) which changed the kernel's behavior on laptops
that boot with closed lids and expect the lid switch state to be
reported accurately by the kernel.
If you boot or resume your laptop with the lid closed on a docking
station while using an external monitor connected to it, both internal
and external displays will light on, while only the external should.
There is a design choice in gdm to only provide the greeter on the
internal display when lit on, so users only see a gray area on the
external monitor. Also, the cursor will not show up as it's by
default on the internal display too.
To "fix" that, users have to open the laptop once and close it once
again to sync the state of the switch with the hardware state.
Even if the "method" operation mode implementation can be buggy on
some platforms, the "open" choice is worse. It breaks docking
stations basically and there is no way to have a user-space hwdb to
fix that.
On the contrary, it's rather easy in user-space to have a hwdb
with the problematic platforms. Then, libinput (1.7.0+) can fix
the state of the lid switch for us: you need to set the udev
property LIBINPUT_ATTR_LID_SWITCH_RELIABILITY to 'write_open'.
When libinput detects internal keyboard events, it will overwrite the
state of the switch to open, making it reliable again. Given that
logind only checks the lid switch value after a timeout, we can
assume the user will use the internal keyboard before this timeout
expires.
For example, such a hwdb entry is:
libinput:name:*Lid Switch*:dmi:*svnMicrosoftCorporation:pnSurface3:*
LIBINPUT_ATTR_LID_SWITCH_RELIABILITY=write_open
Link: https://bugzilla.gnome.org/show_bug.cgi?id=782380
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, extent manipulation operations such as hole punch, range
zeroing, or extent shifting do not record the fact that file data has
changed and thus fdatasync(2) has a work to do. As a result if we crash
e.g. after a punch hole and fdatasync, user can still possibly see the
punched out data after journal replay. Test generic/392 fails due to
these problems.
Fix the problem by properly marking that file data has changed in these
operations.
CC: stable@vger.kernel.org
Fixes: a4bb6b64e3
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
- Make a few Intel Chromebooks with Cherryview DMI firmware
work smoothly.
- A fix for some bogus allocations in the generic group
management code.
- Some GPIO descriptor lookup table stubs. Merged through
the pin control tree for administrative reasons.
- Revert the "bi-directional" and "output-enable" generic
properties: we need more discussions around this. It seems
other SoCs are using input/output gate enablement and these
terms are not correct.
- Fix mux and drive strength atomically in the MXS driver.
- Fix the SPDIF function on sunxi A83T.
- OF table terminators and other small fixes.
-----BEGIN PGP SIGNATURE-----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=S65X
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is an overdue pull request for pin control fixes, the most
prominent feature is to make Intel Chromebooks (and I suspect any
other Cherryview-based Intel thing) happy again, which we really want
to see.
There is a patch hitting drivers/firmware/* that I was uncertain to
who actually manages, but I got Andy Shevchenko's and Dmitry Torokov's
review tags on it and I trust them both 100% to do the right thing for
Intel platform drivers.
Summary:
- Make a few Intel Chromebooks with Cherryview DMI firmware work
smoothly.
- A fix for some bogus allocations in the generic group management
code.
- Some GPIO descriptor lookup table stubs. Merged through the pin
control tree for administrative reasons.
- Revert the "bi-directional" and "output-enable" generic properties:
we need more discussions around this. It seems other SoCs are using
input/output gate enablement and these terms are not correct.
- Fix mux and drive strength atomically in the MXS driver.
- Fix the SPDIF function on sunxi A83T.
- OF table terminators and other small fixes"
* tag 'pinctrl-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunxi: Fix SPDIF function name for A83T
pinctrl: mxs: atomically switch mux and drive strength config
pinctrl: cherryview: Extend the Chromebook DMI quirk to Intel_Strago systems
firmware: dmi: Add DMI_PRODUCT_FAMILY identification string
pinctrl: core: Fix warning by removing bogus code
gpiolib: Add stubs for gpiod lookup table interface
Revert "pinctrl: generic: Add bi-directional and output-enable"
pinctrl: cherryview: Add terminate entry for dmi_system_id tables
This fixes a regression in commit 4d6501dce0 where I didn't notice
that MIPS and OpenRISC were reinitialising p->{set,clear}_child_tid to
NULL after our initialisation in copy_process().
We can simply get rid of the arch-specific initialisation here since it
is now always done in copy_process() before hitting copy_thread{,_tls}().
Review notes:
- As far as I can tell, copy_process() is the only user of
copy_thread_tls(), which is the only caller of copy_thread() for
architectures that don't implement copy_thread_tls().
- After this patch, there is no arch-specific code touching
p->set_child_tid or p->clear_child_tid whatsoever.
- It may look like MIPS/OpenRISC wanted to always have these fields be
NULL, but that's not true, as copy_process() would unconditionally
set them again _after_ calling copy_thread_tls() before commit
4d6501dce0.
Fixes: 4d6501dce0 ("kthread: Fix use-after-free if kthread fork fails")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net> # MIPS only
Acked-by: Stafford Horne <shorne@gmail.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: openrisc@lists.librecores.org
Cc: Jamie Iles <jamie.iles@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Filesystems filter out extended attributes in the "trusted." domain for
unprivlieged callers.
Overlay calls underlying filesystem's method with elevated privs, so need
to do the filtering in overlayfs too.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
For ACPI devices which do not have a _PSC method, the ACPI subsys cannot
query their initial state at boot, so these devices are assumed to have
been put in D0 by the BIOS, but for touchscreens that is not always true.
This commit adds a call to acpi_device_fix_up_power to explicitly put
devices without a _PSC method into D0 state (for devices with a _PSC
method it is a nop). Note we only need to do this on probe, after a
resume the ACPI subsys knows the device is in D3 and will properly
put it in D0.
This fixes the SIS0817 i2c-hid touchscreen on a Peaq C1010 2-in-1
device failing to probe with a "hid_descr_cmd failed" error.
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Analogix 7737 DP to HDMI converter requires reduced M and N values
when to operate correctly at HBR2. We tried to reduce the M/N values for
all devices in commit 9a86cda07a ("drm/i915/dp: reduce link M/N
parameters"), but that regressed some other sinks. Detect this IC by its
OUI value of 0x0022B9 via the DPCD quirk list, and only reduce the M/N
values for that.
v2 by Jani: Rebased on the DP quirk database
v3 by Jani: Rebased on the reworked DP quirk database
v4 by Jani: Improve commit message (Daniel)
Fixes: 9a86cda07a ("drm/i915/dp: reduce link M/N parameters")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93578
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100755
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/2d2e30f8f47d3f28c9b74ca2612336a54585c3ec.1495105635.git.jani.nikula@intel.com
Face the fact, there are Display Port sink and branch devices out there
in the wild that don't follow the Display Port specifications, or they
have bugs, or just otherwise require special treatment. Start a common
quirk database the drivers can query based on the DP device
identification. At least for now, we leave the workarounds for the
drivers to implement as they see fit.
For starters, add a branch device that can't handle full 24-bit main
link Mdiv and Ndiv main link attributes properly. Naturally, the
workaround of reducing main link attributes for all devices ended up in
regressions for other devices. So here we are.
v2: Rebase on DRM DP desc read helpers
v3: Fix the OUI memcmp blunder (Clint)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Tested-by: Clinton Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> # v2
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/91ec198dd95258dbf3bee2f6be739e0da73b4fdd.1495105635.git.jani.nikula@intel.com
Switch to using the common DP helpers instead of using our own.
v2: also remove leftover struct intel_dp_desc (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
An upper dir is marked "impure" to let ovl_iterate() know that this
directory may contain non pure upper entries whose d_ino may need to be
read from the origin inode.
We already mark a non-merge dir "impure" when moving a non-pure child
entry inside it, to let ovl_iterate() know not to iterate the non-merge
dir directly.
Mark also a merge dir "impure" when moving a non-pure child entry inside
it and when copying up a child entry inside it.
This can be used to optimize ovl_iterate() to perform a "pure merge" of
upper and lower directories, merging the content of the directories,
without having to read d_ino from origin inodes.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Takashi Iwai