For consideration:
* Add NVDIMM support - Enables greater testing, mambo device.
* Add IPv6 support built in + additional modules - Because it's 2018 maan.
* Add DEFERRED_STRUCT_PAGE_INIT - Let's see what breaks.
* Add PPC_MEMTRACE - Small powernv debugfs driver for getting hardware traces.
* Add MEMORY_FAILURE - Machine check exceptions can now drive memory failure.
* Turn on FANOTIFY - This is the current filesystem notification feature.
* Turn on SCOM_DEBUGFS - Handy for hardware/firmware debugging, security risk?
* Turn on async SCSI scanning - Let's see what breaks.
* Add MLX5 driver as a module - Popular demand.
* Add CRYPTO_CRCT10DIF_VPMSUM - POWER8 T10DIF acceleration.
* Make a bunch of USB hid drivers modules.
* Make SCSI SG, SR, and FC modules - FC is huge.
* Make video drivers except AST GPU modules - Also huge.
* Make PCI serial driver a module - Uncommon.
* Make more things modules, NFS FS, RAM disk, netconsole, MS-DOS fs.
* Get rid of /dev/port - Not used.
* Remove PPS and PTP subsystms - Unusual.
* Remove legacy BSD ttys - Long dead.
* Remove IDE - Deprecated and replaced with ATA.
* Remove WIRELESS - Until we get POWER9 laptops.
* Remove RAW - Long deprecated in favour of direct IO.
* Remove floppy, parport, and PS2 input devices - not supported.
* Remove virtio drivers, ballooning - We're host only.
* Remove PPP - Sorry Paulus.
This results in a significantly smaller vmlinux:
text data bss dec filename
13143383 5277944 1317856 19739183 vanilla
12263281 4852074 1341720 18457075 patched
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The B43 driver only needs CONFIG_SSB to support the WLAN card found in
the Wii. Configure it accordingly, and disable BCMA bus support to save
a bit of space.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows access to the SD card and the BCM4318 Wifi module.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that there's a GPIO driver for the Wii, let's enable the following
drivers:
- the GPIO driver itself
- gpio-keys
- gpio-poweroff
- gpio-leds and a few LED triggers
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Wii doesn't have built-in Ethernet and USB Ethernet adapters are in
a different menu. Disable CONFIG_ETHERNET to save some space in support
code for Ethernet drivers.
Note that this patch doesn't disable any Ethernet drivers, because they
are not enabled by default.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I no longer have a functional version of this board for even the most
basic sanity boot testing, and they have not been available for purchase
for quite some years now.
There is no point in adding a burden to testing coverage that does
walk all the possible defconfigs, so with all the above in mind, it
makes sense to remove it. Of course it will remain in the git history
for anyone who happens to stumble on one and wants to tinker with it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These drivers haven't seen any recent bug fixing and are two of the last
drivers using the scsi_module.c infrastruture that has been deprecated
15 years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9 when
using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts as well
as "normal" interrupts, and then use that to implement local_t for a ~4x
speedup vs the current atomics-based implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor Interface
(OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe hotpluggable
memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit VDSO.
- Freescale updates from Scott:
"Contains fixes for CPM GPIO and an FSL PCI erratum workaround, plus a
minor cleanup patch."
As well as quite a lot of other changes all over the place, and small fixes and
cleanups as always.
Thanks to:
Alan Modra, Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andreas
Schwab, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman
Khandual, Anton Blanchard, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Bhaktipriya Shridhar, Bryant G. Ly, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Cyril Bur, David Gibson, Desnes A. Nunes
do Rosario, Dmitry Torokhov, Frederic Barrat, Geert Uytterhoeven, Guilherme G.
Piccoli, Gustavo A. R. Silva, Gustavo Romero, Ivan Mikhaylov, Joakim
Tjernlund, Joe Perches, Josh Poimboeuf, Juan J. Alvarez, Julia Cartwright,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre,
Michael Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud, Ram Pai,
Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee, Simon Guo, Stewart
Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann, Vaibhav Jain, Vasyl
Gomonovych.
-----BEGIN PGP SIGNATURE-----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=3rYn
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9
when using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts
as well as "normal" interrupts, and then use that to implement
local_t for a ~4x speedup vs the current atomics-based
implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor
Interface (OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe
hotpluggable memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
VDSO.
- Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
erratum workaround, plus a minor cleanup patch.
As well as quite a lot of other changes all over the place, and small
fixes and cleanups as always.
Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
Vaibhav Jain, Vasyl Gomonovych"
* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
powerpc/mm/radix: Fix build error when RADIX_MMU=n
macintosh/ams-input: Use true and false for boolean values
macintosh: change some data types from int to bool
powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
powerpc/watchdog: Tweak watchdog printks
powerpc/cell: Remove axonram driver
rtc-opal: Fix handling of firmware error codes, prevent busy loops
powerpc/mpc52xx_gpt: make use of raw_spinlock variants
macintosh/adb: Properly mark continued kernel messages
powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
powerpc/numa: Ensure nodes initialized for hotplug
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
powerpc/kernel: Block interrupts when updating TIDR
powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
powerpc/mm/nohash: do not flush the entire mm when range is a single page
powerpc/pseries: Add Initialization of VF Bars
powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
powerpc/eeh: Add EEH notify resume sysfs
powerpc/eeh: Add EEH operations to notify resume
...
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
It doesn't actually do anything. Merge its help text into
EXTRA_FIRMWARE.
Fixes: 5620a0d1aa ("firmware: delete in-kernel firmware")
Fixes: 0946b2fb38 ("firmware: cleanup FIRMWARE_IN_KERNEL message")
Signed-off-by: Benjamin Gilbert <benjamin.gilbert@coreos.com>
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_IRQ_DOMAIN_DEBUG is similar to CONFIG_GENERIC_IRQ_DEBUGFS,
just with less information.
Spring cleanup time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yang Shunyong <shunyong.yang@hxt-semitech.com>
Link: https://lkml.kernel.org/r/20180117142647.23622-1-marc.zyngier@arm.com
These adapters can be found in a number of our systems, so let's
enable the corresponding drivers by default.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CPU6 ERRATA affects only MPC860 revisions prior to C.0. Manufacturing
of those revisiosn was stopped in 1999-2000.
Therefore, it has been almost 20 years since this ERRATA has been
fixed in the silicon.
This patch removes the workaround for that ERRATA.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
i2c-dev provides an interface for userspace programs to interact with I2C
devices, and is very helpful for I2C-related debugging.
Enable it in pseries_defconfig and powernv_defconfig. It's already enabled
in many other powerpc defconfigs.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This configuration is used by the OpenPower firmware for it's
Linux-as-bootloader implementation. Also known as the Petitboot
kernel, this configuration broke in 4.12 (CPU_HOTPLUG=n), so add it to
the upstream tree in order to get better coverage.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit eb3b705aae ("ALSA: Make CONFIG_SND_OSSEMUL user-selectable")
means we need to set CONFIG_SND_OSSEMUL in our configs, otherwise we
lose some of the SND symbols.
And commit 0181307abc ("ALSA: seq: Reorganize kconfig and build")
reorganised things, which causes the churn.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Enable 64K page size and THP. I use ppc64le_defconfig when I need
a single config across guest and host, but having 4K page size
as default is not what I expect. I could move these over to
server.config and merge if ppc64_defconfig is meant for systems
that use 4k pages by default.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Most (all?) distros turn these on, so it makes sense to enable them
for testing coverage, and they're also useful for developers.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Reword change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit a335aaf312 ("usb: misc: remove outdated USB LED driver")
CONFIG_USB_LED was removed, so drop it from our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 76c4969fec ("Bluetooth: hci_uart: fix kconfig
dependency") we can no longer select CONFIG_BT_HCIUART_LL.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 835ea93e9d ("char/genrtc: remove powerpc support"),
CONFIG_GEN_RTC switch from tristate to bool, update the defconfig to
match.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit ca07e1c1e4 ("drivers:usb:fsl:Make fsl ehci drv an
independent driver module"), CONFIG_USB_EHCI_FSL was switched from
built-in to modular. Update the defconfig.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 943cc59219 ("Bluetooth: bpa10x: Use h4_recv_buf helper
for frame reassembly") we no longer need to set CONFIG_BT_HCIUART_H4
in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 8db4c5be88 ("netfilter: move socket lookup
infrastructure to nf_socket_ipv{4,6}.c") we no longer need to set
CONFIG_NETFILTER_XT_MATCH_SOCKET in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 1aefc75b24 ("cpufreq: stats: Make the stats code
non-modular"), the CPU_FREQ_STAT code was made non-modular. Our
defconfig still said =m though, which meant we no longer got the
code at all. Switch the defconfig to =y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit adf0516845 ("netfilter: remove ip_conntrack* sysctl
compat code") we no longer need to set CONFIG_NF_CONNTRACK_PROC_COMPAT
in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 8e14be53f4 ("remove the obsolete hd driver") the
CONFIG_BLK_DEV_HD symbol was removed, so drop it from the defconfig.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit dfb4357da6 ("time: Remove CONFIG_TIMER_STATS") we no
longer need to set CONFIG_TIMER_STATS in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit d92d9c3a14 ("drm: hide legacy drivers with CONFIG_DRM_LEGACY")
CONFIG_DRM_RADEON was moved behind CONFIG_DRM_LEGACY meaning it
stopped being enabled by ppc6xx_defconfig. Although no one has
noticed, given this is basically a legacy platform, it seems anyone
who is using it probably still wants this driver. So turn it back on
for now.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit a03fdcb186 ("drm: Add top level Kconfig option for DRM
fbdev emulation") we no longer need to set CONFIG_FB in our
defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 73d8ef7600 ("Input: mousedev - stop offering PS/2 to
userspace by default") the symbol INPUT_MOUSEDEV went from being
'default y' to 'default n' (implied).
That means we no longer need to explicitly disable it in our
defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 1d0fd57a50 ("logfs: remove from tree"), logfs was removed
from the tree, so we can drop it from our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit d92d9c3a14 ("drm: hide legacy drivers with
CONFIG_DRM_LEGACY") CONFIG_R128 was moved behind CONFIG_DRM_LEGACY
meaning it stopped being enabled by pmac32_defconfig. Although no one
has noticed, given this is basically a legacy platform, it seems
anyone who is using it probably still wants this driver. So turn it
back on for now.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 300ae14946 ("netfilter: select LIBCRC32C together with
SCTP conntrack") we no longer need to set CONFIG_LIBCRC32C in our
defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 67f6d66559 ("powerpc: convert amigaone_defconfig to use
libata PATA drivers") we no longer need to set CONFIG_SCSI in our
defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit de551f2eb2 ("net: Build IPv6 into kernel by default")
we no longer need to set CONFIG_IPV6 in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit e3c4ff6d8c ("EDAC: Remove EDAC_MM_EDAC") CONFIG_EDAC grew
a dependency on CONFIG_RAS. Some of our defconfigs don't have the
latter, which means we lose CONFIG_EDAC, so add CONFIG_RAS to fix
that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit cb74ed278f ("audit: always enable syscall auditing when
supported and audit is enabled") we no longer need to set
CONFIG_AUDITSYSCALL in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit bf4981a006 ("powerpc: Remove the celleb support") we
dropped the celleb support, which made these symbols unselectable
because we no longer select HAS_TX99_SERIAL. So drop them from the
defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
xxxx
In commit 577ec789a7 ("powerpc/cell: Drop select of MEMORY_HOTPLUG")
we removed the last traces of any dependency between
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 43a1dd9b5f ("powerpc/powernv: Add driver for operator
panel on FSP machines") we added CONFIG_POWERNV_OP_PANEL=m to the
powernv defconfig, but it's default m so that's no necessary.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit a311e738b6 ("powerpc/powernv: Make PCI non-optional") we
made PCI (and therefore PCI_MSI) non-optional on powernv, so it
doesn't need to be in the defconfig anymore.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 40e275653e ("powerpc/powernv: Always enable SMP when
building powernv") and 270e2dc9b8 ("powerpc/pseries: Always enable
SMP when building pseries") we forced CONFIG_SMP on for some configs.
Therefore we don't need to set it in those configs anymore.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 6b0b755142 ("perf/core: Rename CONFIG_[UK]PROBE_EVENT to
CONFIG_[UK]PROBE_EVENTS") it was renamed to CONFIG_UPROBE_EVENTS.
Additionally it's default y, and we have the prerequisites enabled, so
we don't need it in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 9654f95a08 ("powerpc: Enable NUMA balancing in
pseries[_le]_defconfig") we added CONFIG_NUMA_BALANCING_DEFAULT_ENABLED
to our defconfigs. But it's already enabled by default, so drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit eedf265aa0 ("devpts: Make each mount of devpts an
independent filesystem.") we no longer need to set
CONFIG_DEVPTS_MULTIPLE_INSTANCES in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 00b9cfa3ff ("mac80111: Add GCMP and GCMP-256 ciphers")
we no longer need to set CONFIG_CRYPTO_GCM in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 3491244c62 ("crypto: echainiv - Set Kconfig default to
m") we no longer need to set CONFIG_CRYPTO_NULL in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 00b9cfa3ff ("mac80111: Add GCMP and GCMP-256 ciphers")
we no longer need to set CONFIG_CRYPTO_NULL in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 826775bbf3 ("crypto: drbg - Add select on sha256") we
no longer need to set CONFIG_CRYPTO_SHA256 in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 12cb3a1c41 ("crypto: xts - Add ECB dependency") we no
longer need to set CONFIG_CRYPTO_ECB in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 401e4238f3 ("crypto: rng - Make DRBG the default RNG")
we no longer need to set CONFIG_CRYPTO_HMAC in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit ccf5c442a1 ("crypto: vmx - Convert to CPU feature based
module autoloading") we no longer need to set
CONFIG_CRYPTO_DEV_VMX_ENCRYPT in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit a85406afeb ("netfilter: conntrack: built-in support for
SCTP"), NF_CT_PROTO_SCTP switched from tristate to bool and became
default y. Similarly in commit 9b91c96c5d ("netfilter: conntrack:
built-in support for UDPlite"), NF_CT_PROTO_UDPLITE switched from
tristate to bool and became default y.
We had a few configs which set them to =m, which is no longer valid.
We don't need to change them to =y because both symbols are default y
and are enabled automatically based on the other symbols in the
affected defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit a5e4bd9913 ("of_mdio: select fixed phy support
unconditionally"), CONFIG_OF_MDIO began selecting CONFIG_FIXED_PHY.
That means we no longer need to set it some of our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 961518259b ("rcu: Enable RCU tracepoints by default to aid
in debugging"), CONFIG_RCU_TRACE was made default y (if CONFIG_TREE_RCU=y,
which it is for some of our configs).
That in turn causes CONFIG_TREE_RCU_TRACE to be enabled, which selects
CONFIG_DEBUG_FS. The end result is that CONFIG_DEBUG_FS is forced on,
meaning we don't have to enable it in some of our configs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit e334cd69fa ("Move CONFIG_DEVKMEM default to n") we no
longer need to set CONFIG_DEVKMEM in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit f76be61755 ("Make CONFIG_FHANDLE default y") we no
longer need to set CONFIG_FHANDLE in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 73d8ef7600 ("Input: mousedev - stop offering PS/2 to userspace by
default") (Jan 2017), CONFIG_INPUT_MOUSEDEV was switched from default y to
default n, with the explanation:
Evdev interface has been available for many years and by now everyone
is switched to using it, so let's stop offering /dev/input/mouseN
and /dev/psaux by default.
We had a number of configs which had it enabled, but going by the above
explanation probably don't need it enabled anymore.
So drop the last remnants of it from our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 401e4238f3 ("crypto: rng - Make DRBG the default RNG") we no longer need to set CONFIG_CRYPTO_ANSI_CPRNG in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's a non-trivial dependency between some commits we want to put in
next and the KVM prefetch work around that went into fixes. So merge
fixes into next.
Add mmc0 changes for enabling arasan emmc and change
defconfig appropriately.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 05a4a95279 ("kernel/watchdog: split up config options"),
CONFIG_LOCKUP_DETECTOR was split into two separate config options,
CONFIG_HARDLOCKUP_DETECTOR and CONFIG_SOFTLOCKUP_DETECTOR.
Our defconfigs still have CONFIG_LOCKUP_DETECTOR=y, but that is no longer
user selectable, and we don't mention the new options, so we end up with
none of them enabled.
So update the defconfigs to turn on the new SOFT and HARD options, the
end result being the same as what we had previously.
Fixes: 05a4a95279 ("kernel/watchdog: split up config options")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Although pretty much everyone using powernv is running little endian,
we should still test we can build for big endian. So add a
powernv_be_defconfig, which is autogenerated by flipping the endian
symbol in powernv_defconfig.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
This patch adds default FSP2 config for main usage.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we use a 128TB
virtual address space, but a process can request access to the full 512TB by
passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator Interface
Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and runtime.
- Several small fixes and cleanups to the kprobes code, as well as support for
KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts, correctly treating
them as NMIs, giving them a dedicated stack and using a new hypervisor call
to trigger them, all of which should aid debugging and robustness.
Many fixes and other minor enhancements.
Thanks to:
Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anshuman Khandual, Anton Blanchard, Balbir Singh, Ben
Hutchings, Benjamin Herrenschmidt, Bhupesh Sharma, Chris Packham, Christian
Zigotzky, Christophe Leroy, Christophe Lombard, Daniel Axtens, David Gibson,
Gautham R. Shenoy, Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli,
Hamish Martin, Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan,
Mahesh J Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran,
Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell Currey, Sukadev
Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C. Harding, Tyrel Datwyler,
Uma Krishnan, Vaibhav Jain, Vipin K Parashar, Yang Shi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vSF3
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we
use a 128TB virtual address space, but a process can request access
to the full 512TB by passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator
Interface Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and
runtime.
- Several small fixes and cleanups to the kprobes code, as well as
support for KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts,
correctly treating them as NMIs, giving them a dedicated stack and
using a new hypervisor call to trigger them, all of which should
aid debugging and robustness.
- Many fixes and other minor enhancements.
Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple,
Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual, Anton
Blanchard, Balbir Singh, Ben Hutchings, Benjamin Herrenschmidt,
Bhupesh Sharma, Chris Packham, Christian Zigotzky, Christophe Leroy,
Christophe Lombard, Daniel Axtens, David Gibson, Gautham R. Shenoy,
Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli, Hamish Martin,
Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Mahesh J
Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell
Currey, Sukadev Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C.
Harding, Tyrel Datwyler, Uma Krishnan, Vaibhav Jain, Vipin K Parashar,
Yang Shi"
* tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (214 commits)
powerpc/64s: Power9 has no LPCR[VRMASD] field so don't set it
powerpc/powernv: Fix TCE kill on NVLink2
powerpc/mm/radix: Drop support for CPUs without lockless tlbie
powerpc/book3s/mce: Move add_taint() later in virtual mode
powerpc/sysfs: Move #ifdef CONFIG_HOTPLUG_CPU out of the function body
powerpc/smp: Document irq enable/disable after migrating IRQs
powerpc/mpc52xx: Don't select user-visible RTAS_PROC
powerpc/powernv: Document cxl dependency on special case in pnv_eeh_reset()
powerpc/eeh: Clean up and document event handling functions
powerpc/eeh: Avoid use after free in eeh_handle_special_event()
cxl: Mask slice error interrupts after first occurrence
cxl: Route eeh events to all drivers in cxl_pci_error_detected()
cxl: Force context lock during EEH flow
powerpc/64: Allow CONFIG_RELOCATABLE if COMPILE_TEST
powerpc/xmon: Teach xmon oops about radix vectors
powerpc/mm/hash: Fix off-by-one in comment about kernel contexts ids
powerpc/pseries: Enable VFIO
powerpc/powernv: Fix iommu table size calculation hook for small tables
powerpc/powernv: Check kzalloc() return value in pnv_pci_table_alloc
powerpc: Add arch/powerpc/tools directory
...
Move all the EDAC core functionality behind CONFIG_EDAC and get rid of
that indirection. Update defconfigs which had it.
While at it, fix dependencies such that EDAC depends on RAS for the
tracepoints.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-edac@vger.kernel.org
The config option for the POWER8 crc32c recently changed from
CONFIG_CRYPT_CRC32C_VPMSUM to CONFIG_CRYPTO_CRC32C_VPMSUM. Update
the configs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Most people use perf these days, so save about 31kB by making oprofile
a module.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It turns out cloud-config uses ISO9660 filesystems to inject
configuration data into cloud images. The cloud-config failures when
ISO9660_FS is not enabled are cryptic, and building it in makes
mainline testing easier, so re-enable it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- An update of the disassembly code used by xmon to the latest versions in
binutils. We've received permission from all the authors of the relevant
binutils changes to relicense their changes to the relevant files from GPLv3
to GPLv2, for inclusion in Linux. Thanks to Peter Bergner for doing the leg
work to get permission from everyone.
- Addition of the "architected" Power9 CPU table entry, allowing us to boot
in Power9 architected mode under a hypervisor.
- Updates to the Power9 PMU code.
- Implementation of clear_bit_unlock_is_negative_byte() to optimise
unlock_page().
- Freescale updates from Scott: "Highlights include 8xx breakpoints and perf,
t1042rdb display support, and board updates."
Thanks to:
Al Viro, Andrew Donnellan, Aneesh Kumar K.V, Balbir Singh, Douglas Miller,
Frédéric Weisbecker, Gavin Shan, Madhavan Srinivasan, Michael Roth, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Peter Bergner, Paul E. McKenney,
Rashmica Gupta, Russell Currey, Sahil Mehta, Stewart Smith.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rspd
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"Highlights include:
- an update of the disassembly code used by xmon to the latest
versions in binutils. We've received permission from all the
authors of the relevant binutils changes to relicense their changes
to the relevant files from GPLv3 to GPLv2, for inclusion in Linux.
Thanks to Peter Bergner for doing the leg work to get permission
from everyone.
- addition of the "architected" Power9 CPU table entry, allowing us
to boot in Power9 architected mode under a hypervisor.
- updates to the Power9 PMU code.
- implementation of clear_bit_unlock_is_negative_byte() to optimise
unlock_page().
- Freescale updates from Scott: "Highlights include 8xx breakpoints
and perf, t1042rdb display support, and board updates."
Thanks to:
Al Viro, Andrew Donnellan, Aneesh Kumar K.V, Balbir Singh, Douglas
Miller, Frédéric Weisbecker, Gavin Shan, Madhavan Srinivasan,
Michael Roth, Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Peter
Bergner, Paul E. McKenney, Rashmica Gupta, Russell Currey, Sahil
Mehta, Stewart Smith"
* tag 'powerpc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (48 commits)
powerpc: Remove leftover cputime_to_nsecs call causing build error
powerpc/mm/hash: Always clear UPRT and Host Radix bits when setting up CPU
powerpc/optprobes: Fix TOC handling in optprobes trampoline
powerpc/pseries: Advertise Hot Plug Event support to firmware
cxl: fix nested locking hang during EEH hotplug
powerpc/xmon: Dump memory in CPU endian format
powerpc/pseries: Revert 'Auto-online hotplugged memory'
powerpc/powernv: Make PCI non-optional
powerpc/64: Implement clear_bit_unlock_is_negative_byte()
powerpc/powernv: Remove unused variable in pnv_pci_sriov_disable()
powerpc/kernel: Remove error message in pcibios_setup_phb_resources()
powerpc/mm: Fix typo in set_pte_at()
pci/hotplug/pnv-php: Disable MSI and PCI device properly
pci/hotplug/pnv-php: Disable surprise hotplug capability on conflicts
pci/hotplug/pnv-php: Remove WARN_ON() in pnv_php_put_slot()
powerpc: Add POWER9 architected mode to cputable
powerpc/perf: use is_kernel_addr macro in perf_get_misc_flags()
powerpc/perf: Avoid FAB_*_MATCH checks for power9
powerpc/perf: Add restrictions to PMC5 in power9 DD1
powerpc/perf: Use Instruction Counter value
...
Highlights include:
- Support for direct mapped LPC on POWER9, giving Linux direct access to
devices that may be on there such as a UART.
- Memory hotplug support for the Power9 Radix MMU.
- Add new AUX vectors describing the processor's cache geometry, to be used by
glibc.
- The ability for a guest to ask the hypervisor to resize the guest's hash
table, and in addition support for doing so automatically when memory is
hotplugged into/out-of the guest. This allows the hash table to be sized
based on the current memory usage of the guest, rather than the maximum
possible memory usage.
- Implementation of optprobes (kprobe optimisation) for powerpc.
In addition there's the topic branch shared with the KVM tree, which includes
support for guests to use the Radix MMU on Power9.
Thanks to:
Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton Blanchard,
Benjamin Herrenschmidt, Chris Packham, Daniel Axtens, Daniel Borkmann, David
Gibson, Finn Thain, Gautham R. Shenoy, Gavin Shan, Greg Kurz, Joel Stanley,
John Allen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Neuling, Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi
Bangoria, Reza Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Icle
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for direct mapped LPC on POWER9, giving Linux direct access
to devices that may be on there such as a UART.
- Memory hotplug support for the Power9 Radix MMU.
- Add new AUX vectors describing the processor's cache geometry, to
be used by glibc.
- The ability for a guest to ask the hypervisor to resize the guest's
hash table, and in addition support for doing so automatically when
memory is hotplugged into/out-of the guest. This allows the hash
table to be sized based on the current memory usage of the guest,
rather than the maximum possible memory usage.
- Implementation of optprobes (kprobe optimisation) for powerpc.
In addition there's the topic branch shared with the KVM tree, which
includes support for guests to use the Radix MMU on Power9.
Thanks to:
Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton
Blanchard, Benjamin Herrenschmidt, Chris Packham, Daniel Axtens,
Daniel Borkmann, David Gibson, Finn Thain, Gautham R. Shenoy, Gavin
Shan, Greg Kurz, Joel Stanley, John Allen, Madhavan Srinivasan,
Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi Bangoria, Reza
Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun"
* tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (129 commits)
powerpc/mm/radix: Skip ptesync in pte update helpers
powerpc/mm/radix: Use ptep_get_and_clear_full when clearing pte for full mm
powerpc/mm/radix: Update pte update sequence for pte clear case
powerpc/mm: Update PROTFAULT handling in the page fault path
powerpc/xmon: Fix data-breakpoint
powerpc/mm: Fix build break with BOOK3S_64=n and MEMORY_HOTPLUG=y
powerpc/mm: Fix build break when CMA=n && SPAPR_TCE_IOMMU=y
powerpc/mm: Fix build break with RADIX=y & HUGETLBFS=n
powerpc/pseries: Fix typo in parameter description
powerpc/kprobes: Remove kprobe_exceptions_notify()
kprobes: Introduce weak variant of kprobe_exceptions_notify()
powerpc/ftrace: Fix confusing help text for DISABLE_MPROFILE_KERNEL
powerpc/powernv: Fix opal_exit tracepoint opcode
powerpc: Add a prototype for mcount() so it can be versioned
powerpc: Drop GPL from of_node_to_nid() export to match other arches
powerpc/kprobes: Optimize kprobe in kretprobe_trampoline()
powerpc/kprobes: Implement Optprobes
powerpc/kprobes: Fixes for kprobe_lookup_name() on BE
powerpc: Add helper to check if offset is within relative branch range
powerpc/bpf: Introduce __PPC_SH64()
...
This reverts commit ec99907244 ("powerpc/pseries: Auto-online
hotplugged memory"), and 9dc512819e ("powerpc: Fix unused function
warning 'lmb_to_memblock'").
Using the auto-online acpability does online added memory but does not
update the associated device struct to indicate that the memory is
online. This causes the pseries memory DLPAR code to fail when trying to
remove a LMB that was previously removed and added back. This happens
when validating that the LMB is removable.
This patch reverts to the previous behavior of calling device_online()
to online the LMB when it is DLPAR added and moves the lmb_to_memblock()
routine out of CONFIG_MEMORY_HOTREMOVE now that we call it for add.
Fixes: ec99907244 ("powerpc/pseries: Auto-online hotplugged memory")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These are common on bare metal machines, so put them in the defconfig.
This adds 216KB to the vmlinux size
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This doesn't have any benefit apart from saving a small amount of memory
when it is disabled. The ifdef hackery in the code makes it dirty
unnecessarily.
Clean it up by removing the Kconfig option completely. Few defconfigs
are also updated and CONFIG_CPU_FREQ_STAT_DETAILS is replaced with
CONFIG_CPU_FREQ_STAT now in them, as users wanted stats to be enabled.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit db9112173b ("powerpc: Turn on BPF_JIT in ppc64_defconfig")
only added BPF_JIT to the ppc64 defconfig. Add it to our powernv
and pseries defconfigs too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is not maintained and thus obsolete. corenet32_smp_defconfig can be
used as reference for the kmcoge4/kmp204x boards.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for secure and
trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and store
them as relative offsets to save space in the kernel image & memory.
- Allow building the kernel with thin archives, which should allow us to build
an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the kernel endian
from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9 Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage support,
qbman fixes/cleanup, device tree updates, and some misc cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual,
Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz, Christophe Jaillet,
Christophe Leroy, Denis Kirjanov, Elimar Riesebieter, Frederic Barrat,
Gautham R. Shenoy, Geliang Tang, Geoff Levand, Jack Miller, Johan Hovold,
Lars-Peter Clausen, Libin, Madhavan Srinivasan, Michael Neuling, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin,
Rashmica Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xOzf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for
secure and trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to
SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and
store them as relative offsets to save space in the kernel image &
memory.
- Allow building the kernel with thin archives, which should allow us
to build an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the
kernel endian from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9
Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via
debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage
support, qbman fixes/cleanup, device tree updates, and some misc
cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz,
Christophe Jaillet, Christophe Leroy, Denis Kirjanov, Elimar
Riesebieter, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff
Levand, Jack Miller, Johan Hovold, Lars-Peter Clausen, Libin,
Madhavan Srinivasan, Michael Neuling, Nathan Fontenot, Naveen N.
Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin, Rashmica
Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain"
[ And thanks to Michael, who took time off from a new baby to get this
pull request done. - Linus ]
* tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (174 commits)
powerpc/fsl/dts: add FMan node for t1042d4rdb
powerpc/fsl/dts: add sg_2500_aqr105_phy4 alias on t1024rdb
powerpc/fsl/dts: add QMan and BMan nodes on t1024
powerpc/fsl/dts: add QMan and BMan nodes on t1023
soc/fsl/qman: test: use DEFINE_SPINLOCK()
powerpc/fsl-lbc: use DEFINE_SPINLOCK()
powerpc/8xx: Implement support of hugepages
powerpc: get hugetlbpage handling more generic
powerpc: port 64 bits pgtable_cache to 32 bits
powerpc/boot: Request no dynamic linker for boot wrapper
soc/fsl/bman: Use resource_size instead of computation
soc/fsl/qe: use builtin_platform_driver
powerpc/fsl_pmc: use builtin_platform_driver
powerpc/83xx/suspend: use builtin_platform_driver
powerpc/ftrace: Fix the comments for ftrace_modify_code
powerpc/perf: macros for power9 format encoding
powerpc/perf: power9 raw event format encoding
powerpc/perf: update attribute_group data structure
powerpc/perf: factor out the event format field
powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown
...
Enable CONFIG_KEXEC_FILE in powernv_defconfig, ppc64_defconfig and
pseries_defconfig.
It depends on CONFIG_CRYPTO_SHA256=y, so add that as well.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These config changes build:
drivers/power/reset/gpio-poweroff.c
drivers/power/reset/gpio-restart.c
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
These are the PPC optimised versions of various crypto algorithms, so we
should turn them on by default to get test coverage.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts storcenter_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts pseries_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ppc6xx_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ppc64e_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ppc64_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts pmac32_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
This patch disables deprecated IDE subsystem in pasemi_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts maple_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts g5_defconfig to use libata PATA drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts chrp32_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts cell_defconfig to use libata PATA drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts amigaone_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
No one uses reiserfs much these days, or is likely to in future. So drop
it from pseries and powernv defconfigs to save time and space. It's
still enabled in ppc64_defconfig so we get some build coverage.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Freescale updates from Scott:
"Highlights include qbman support (a prerequisite for datapath drivers
such as ethernet), a PCI DMA fix+improvement, reset handler changes, more
8xx optimizations, and some cleanups and fixes."
We are starting to see i40e adapters in recent machines, so enable
it in our configs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change a few devices and filesystems that are seldom used any more
from built in to modules. This reduces our vmlinux about 500kB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we issue a system reset, every CPU in the box prints an Oops,
including a backtrace. Each of these can be quite large (over 4kB)
and we may end up wrapping the ring buffer and losing important
information.
Bump the base size from 128kB to 256kB and the per CPU size from
4kB to 8kB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We see big improvements with the VMX crypto functions (often 10x or more),
so enable it as a module.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Enable the drivers on the powerpc arch.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
A recent update (commit id 31bc3858ea) allows for automatically
onlining memory that is added. This patch sets the config option
CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE=y for pseries and updates the
pseries memory hotplug code so that DLPAR added memory can be
automatically onlined instead of explicitly onlining the memory.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch disables deprecated IDE subsystem in pq2fads_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Add support for the Artesyn MVME7100 Single Board Computer.
The MVME7100 is a 6U form factor VME64 computer with:
- A two e600 cores Freescale MPC8641D CPU
- 2 GB of DDR2 onboard memory
- Four Gigabit Ethernets
- Five 16550 compatible UARTs
- One USB 2.0 port
- Two PCI/PCI eXpress Mezzanine Card (PMC/XMC) Slots
- A DS1375 Real Time Clock (RTC)
- 512 KB of Non-Volatile Memory (NVRAM)
- Two 64 KB EEPROMs
- 128 MB NOR and 4/8 GB NAND Flash
This patch is based on linux-4.7-rc1 and has been only boot tested.
Limitations:
This patch covers only models 171 and 173
No plans to support CPLD timers
Know issues:
All four PHYs work in polling mode
Configuration is missing for:
PCI IDSEL and PCI Interrupt definition
Support is missing for:
Cache and memory controllers (which are very similar to the 85xx ones
but right now I don't know if we can re-use their support)
Watchdog, USB, NVRAM, NOR, NAND, EEPROMs, VME, PMC/XMC and RTC
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>
This is so we can use the powernv_flash mtd driver as an block
device.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement new character device driver to allow access from user space
to the operator panel display present on IBM Power Systems machines
with FSPs.
This will allow status information to be presented on the display which
is visible to a user.
The driver implements a character buffer which a user can read/write
by accessing the device (/dev/op_panel). This buffer is then displayed on
the operator panel display. Any attempt to write past the last character
position will have no effect and attempts to write more characters than
the size of the display will be truncated. The device may only be accessed
by a single process at a time.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- dts: rename 'ide-disk' to 'disk-activity'
- defconfig: rename 'ADB_PMU_LED_IDE' to 'ADB_PMU_LED_DISK'
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy, Cyril
Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell Currey,
Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_* helpers from
Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/relaxed
variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs from Wei
Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter values,
display domain indices in sysfs, eliminate domain suffix in event names,
from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit checksum
optimizations, 86xx consolidation, e5500/e6500 cpu hotplug, more fman and
other dt bits, and minor fixes/cleanup."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qkAt
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This was delayed a day or two by some build-breakage on old toolchains
which we've now fixed.
There's two PCI commits both acked by Bjorn.
There's one commit to mm/hugepage.c which is (co)authored by Kirill.
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul
Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh
Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy,
Cyril Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell
Currey, Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_*
helpers from Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/
relaxed variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas
Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs
from Wei Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell
Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev
Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter
values, display domain indices in sysfs, eliminate domain suffix in
event names, from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit
checksum optimizations, 86xx consolidation, e5500/e6500 cpu
hotplug, more fman and other dt bits, and minor fixes/cleanup"
* tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (179 commits)
powerpc: Fix unrecoverable SLB miss during restore_math()
powerpc/8xx: Fix do_mtspr_cpu6() build on older compilers
powerpc/rcpm: Fix build break when SMP=n
powerpc/book3e-64: Use hardcoded mttmr opcode
powerpc/fsl/dts: Add "jedec,spi-nor" flash compatible
powerpc/T104xRDB: add tdm riser card node to device tree
powerpc32: PAGE_EXEC required for inittext
powerpc/mpc85xx: Add pcsphy nodes to FManV3 device tree
powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)
powerpc/86xx: Introduce and use common dtsi
powerpc/86xx: Update device tree
powerpc/86xx: Move dts files to fsl directory
powerpc/86xx: Switch to kconfig fragments approach
powerpc/86xx: Update defconfigs
powerpc/86xx: Consolidate common platform code
powerpc32: Remove one insn in mulhdu
powerpc32: small optimisation in flush_icache_range()
powerpc: Simplify test in __dma_sync()
powerpc32: move xxxxx_dcache_range() functions inline
powerpc32: Remove clear_pages() and define clear_page() inline
...
This patch show how defconfigs appear if the kconfig fragment approach is
used.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch disables deprecated IDE subsystem in mpc8610_hpcd_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch disables deprecated IDE subsystem in stx_gp3_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch disables deprecated IDE subsystem in ksi8560_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch disables deprecated IDE subsystem in mpc834x_itx_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Most current OpenPOWER platforms have an AST BMC, so add graphics
support via the AST DRM driver.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are a few firmware-provided interfaces for OpenPOWER platforms:
the PRD infrastructure, IPMI support, and MTD access to the PNOR flash.
This change adds these to powernv_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This change adds a defconfig for the non-virtualised power platforms,
based on pseries_defconfig, but without pseries, and little-endian,
and no OF trampoline.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_KEYS_DEBUG_PROC_KEYS is no longer an option as /proc/keys is now
mandatory if the keyrings facility is enabled (it's used by libkeyutils in
userspace).
The defconfig references were removed with:
perl -p -i -e 's/CONFIG_KEYS_DEBUG_PROC_KEYS=y\n//' \
`git grep -l CONFIG_KEYS_DEBUG_PROC_KEYS=y`
and the integrity Kconfig fixed by hand.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Andreas Ziegler <andreas.ziegler@fau.de>
cc: Dmitry Kasatkin <dmitry.kasatkin@huawei.com>
Enable TWR_P102x option by default in mpc85xx_basic_defconfig to support
p1025twr board.
Signed-off-by: Pengbo Li <Pengbo.Li@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
All users of QPACE have upgraded to QPACE2 so remove the Cell QPACE code.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Kconfig: remove BE-only platforms from LE kernel build from Boqun Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference. from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from Colin Ian King
- Disable hugepd for 64K page size. from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file. from Paul Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages. from Christophe Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e kexec/kdump
support, a rework of the qoriq clock driver, device tree changes including
qoriq fman nodes, support for a new 85xx board, and some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for MPC512x
LocalPlus Bus FIFO with its device tree binding documentation, mpc512x
device tree updates and some minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YwcM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Kconfig: remove BE-only platforms from LE kernel build from Boqun
Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael
Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar
K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan
Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel
Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from
Colin Ian King
- Disable hugepd for 64K page size, from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh
Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul
Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael
Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael
Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe
Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael
Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis
Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages, from Christophe
Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro
Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from
Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building
with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e
kexec/kdump support, a rework of the qoriq clock driver, device tree
changes including qoriq fman nodes, support for a new 85xx board, and
some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for
MPC512x LocalPlus Bus FIFO with its device tree binding
documentation, mpc512x device tree updates and some minor fixes.
* tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits)
powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc()
powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id()
powerpc/pseries: Correct string length in pseries_of_derive_parent()
powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry
powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)
powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan
powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes
powerpc: handle error case in cpm_muram_alloc()
powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake
powerpc/book3e-64: Enable kexec
powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop
powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32
powerpc/book3e-64/kexec: Enable SMP release
powerpc/book3e-64/kexec: create an identity TLB mapping
powerpc/book3e-64: Don't limit paca to 256 MiB
powerpc/book3e/kdump: Enable crash_kexec_wait_realmode
powerpc/book3e: support CONFIG_RELOCATABLE
powerpc/booke64: Fix args to copy_and_flush
powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts
powerpc/e6500: kexec: Handle hardware threads
...
This driver for Freescale MPC512x LocalPlus Bus FIFO (called SCLPC
in the Reference Manual) allows Direct Memory Access transfers
between RAM and peripheral devices on LocalPlus Bus.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The TUNE_CELL option allows you to build a kernel that runs on multiple
CPUs but is tuned (ie. optimised) to run on Cell CPUs. Now days no one
is building a distro in that fashion, and any users who are building
custom kernels for their Cell machines are better off building with
CONFIG_CELL_CPU, which builds a kernel that only runs on Cell and
therefore can be optimised even more aggresively.
Dropping the option also avoids confusing other users, who are presented
with an option to tune for Cell when they are not building for a Cell
CPU at all.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 086b91d052 ("scsi_dh: integrate into the core SCSI code")
changed CONFIG_SCSI_DH from tristate to bool.
Our defconfigs have CONFIG_SCSI_DH=m, which the kconfig machinery warns
us is invalid, but instead of converting it to =y it leaves it unset.
This means we loose the CONFIG_SCSI_DH code and everything that depends
on it.
So convert the values in the defconfigs to =y.
Fixes: 086b91d052 ("scsi_dh: integrate into the core SCSI code")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Freescale updates from Scott:
"Highlights include 32-bit memcpy/memset optimizations, checksum
optimizations, 85xx config fragments and updates, device tree updates,
e6500 fixes for non-SMP, and misc cleanup and minor fixes."
Commit 84ad6e5c added LEDS support for PowerNV platform. Lets
update ppc64_defconfig to pick LEDS driver.
PowerNV LEDS driver looks for "/ibm,opal/leds" node in device
tree and loads if this node exists. Hence added it as 'm'.
Also note that powernv LEDS driver needs NEW_LEDS and LEDS_CLASS
as well. Hence added them to config file.
mpe: Also add them to pseries_defconfig, which is currently also used
for powernv systems.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Cc: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A working rtc kernel driver is needed so that hwclock can synchronize
system clock to rtc during shutdown/boot. We already have a powernv
platform rtc driver located at drivers/rtc/rtc-opal.c. However it depends
on CONFIG_RTC_CLASS which is disabled by default. Hence the driver isn't
enabled and not compiled for the powernv kernel.
We fix this by enabling rtc class support in pseries defconfig which
enables this driver and compiles it into the pseries kernel. In case
CONFIG_PPC_POWERNV is not enabled we fallback to 'Generic RTC support'
driver which emulates the legacy 'PC RTC driver'.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Aquantia PHYs used on platforms such as T2080RDB, T1024RDB.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The PHY uses XAUI interface to connect to MAC, mostly the PHY used on
riser card.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Unify mpc85xx and corenet configs using fragments, to ease maintenance
and avoid the sort of drift that the previous patch fixed.
Hardware and software options are separated, with the hope that other
embedded platforms could share the software options, and to make it
easier to maintain custom/alternate configs that focus on either
hardware or software options.
Due to the previous patch, this patch should not affect the results of
any of the affected defconfigs -- only how those results are achieved.
The resulting config is more or less the union of the options that any
of the configs previously selected. No attempt was made in this (or
the previous) patch to edit out questionable options, but this patch
will make it easier to do so in future patches.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The mpc85xx and corenet configs have many differences between them that
can't be explained by the target hardware of each config. The next
patch will consolidate these targets using kconfig fragments; this
patch shows what the resulting defconfigs will look like (generated by
using savedefconfig on a fragment-generated config).
Signed-off-by: Scott Wood <scottwood@freescale.com>
corenet32_smp_defconfig is missing some things that modern distros
require, enable them.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Scott Wood <scottwood@freescale.com>
By default we enable DMA(CONFIG_FSL_DMA) support
which are needed on P2041RDB, P3041DS, P4080DS,
B4860QDS, etc.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Freescale updates from Scott:
"Highlights include more 8xx optimizations, an e6500 hugetlb optimization,
QMan device tree nodes, t1024/t1023 support, and various fixes and
cleanup."
Since commit 100832abf0 ("usb: isp1760: Make HCD support
optional"), CONFIG_USB_ISP1760_HCD is automatically selected when
needed. Enabling that option in the defconfig is now a no-op, and no
longer enables ISP1760 HCD support.
Re-enable the ISP1760 driver in the defconfig by enabling
USB_ISP1760_HOST_ROLE instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Nicholas Piggin