Currently, to define a GPIO number, we're using something like :
#define EFIKAMX_PCBID0 (2*32 + 16)
to define GPIO 3 16.
This is not really readable and it's error prone imho (note the 3 vs 2).
So, I'm introducing a new macro to define this in a better way. Now, the
code sample become :
#define EFIKAMX_PCBID0 IMX_GPIO_NR(3, 16)
v2:
- move to gpio.h
- add parens & spaces
- switch to IMX_GPIO_NR instead of MX51_GPIO_NR
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In commit 2c20b9f (ARM: mx25: dynamically allocate mxc-ehci devices) I
changed the offset to the value specified in the reference manual
intending to test this change on hardware. This slipped through and now
prooved to be wrong. So fix it and add a comment about the
documentation being wrong.
Reported-by: Jaume Ribot <jaume@fqingenieria.es>
Cc: Michael Trimarchi <trimarchi@gandalf.sssup.it>
Cc: Shawn Guo <shawn.gsc@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The SDMA firmware consists of a ROM part and a RAM part.
The ROM part is always present in the SDMA engine and
is sufficient for many cases.
This patch allows to pass in platform data containing
the script addresses in ROM, so loading a firmware is
optional now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Instead of reading the silicon version from ROM, we should
read the SREV register from the IIM.
Freescale has dropped all support for MX51 REV1.0, only MX51
REV 2.0 and 3.0 are valid.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efikamx board is using a gpio to reset the board so add support
for it
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- add definition to configure pads as ESDHC{1,2} WP and CD
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- ALT0 is used to set GPIO mode of GPIO_1_{2,3,4,5,6,7,8,9} but it's ALT1
for GPIO_1_{0,1}.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The following patch is a first step to convert the 'struct pad_desc'
to a bitmapped cookie to facilitate adding platform specific pullup or
drive strength definitions to existing pad definitions without need to
rewrite the complete pad def.
The patch wraps 'struct pad_desc' in an opaque data type and
introduces macros to access the individual members.
This patch does not constitute any functional change!
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While adapting the #defines for this I noticed that the offset
used for USB HS on i.MX35 differs from the documented offset.
I kept the working offset and commented that the documentation
differs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Compared to the static devices the dynamic have a DMA resource.
This should be save as it seems unused in the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The mxc-keypad device seems to be the result of an early and partial
merge of the keypad driver. It's unused and there is no corresponding
driver available, so just remove it.
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
To use common macros to define the gpio ports for imx{1,21,25,27} the
existing ones had to made more general and a few more base address defines
were necessary.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
According to the reference manual of the i.MX25 the host controller uses an
offset of 0x200 not 0x400 as was specified in the resources for mxc_usbh2.
Needs-Testing: yes
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Group soc specific data in a global struct instead of repeating it for each
call to imxXX_add_flexcanX. The structs holding the actual data are placed
in .init.constdata and so don't do much harm. Compared to the previous
approach this reduces code size to call imx_add_flexcan.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently there is no platform data used in the driver. In case this
changes and for consistency NULL is passed unused to the soc specific
functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently there is no platform data used in the driver. In case this
changes NULL is passed unused to the soc specific functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Now only the virtual addresses [0xf4000000, 0xf5ffffff] are used for
static per-SoC mappings. The few mappings of whole chip selects are
moved accordingly.
The now wrong defines for virtual base addresses are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This allows changing the mapping without the need to adapt all users.
While at it remove some unneeded casts to void __iomem *, this is already
taken care for in the IO_ADDRESS macros
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This makes less code rely on the virtual constants.
To further simplify code and reduce the needed boilerplate when
defining the static mappings a new helper macro is defined in
mach/hardware.h.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This makes it more assembler friendly and allows it to be used in situation
that need an unsigned long and not a pointer. Also the naming is
clearer. IOMEM is introduced without IMX_ prefix as it is used this way
in more than one ARM subarch and it might become globally available
soon.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (215 commits)
ARM: memblock: setup lowmem mappings using memblock
ARM: memblock: move meminfo into find_limits directly
ARM: memblock: convert free_highpages() to use memblock
ARM: move freeing of highmem pages out of mem_init()
ARM: memblock: convert memory detail printing to use memblock
ARM: memblock: use memblock to free memory into arm_bootmem_init()
ARM: memblock: use memblock when initializing memory allocators
ARM: ensure membank array is always sorted
ARM: 6466/1: implement flush_icache_all for the rest of the CPUs
ARM: 6464/2: fix spinlock recursion in adjust_pte()
ARM: fix memblock breakage
ARM: 6465/1: Fix data abort accessing proc_info from __lookup_processor_type
ARM: 6460/1: ixp2000: fix type of ixp2000_timer_interrupt
ARM: 6449/1: Fix for compiler warning of uninitialized variable.
ARM: 6445/1: fixup TCM memory types
ARM: imx: Add wake functionality to GPIO
ARM: mx5: Add gpio-keys to mx51 babbage board
ARM: imx: Add gpio-keys to plat-mxc
mx31_3ds: Fix spi registration
mx31_3ds: Fix the logic for detecting the debug board
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (48 commits)
DMAENGINE: move COH901318 to arch_initcall
dma: imx-dma: fix signedness bug
dma/timberdale: simplify conditional
ste_dma40: remove channel_type
ste_dma40: remove enum for endianess
ste_dma40: remove TIM_FOR_LINK option
ste_dma40: move mode_opt to separate config
ste_dma40: move channel mode to a separate field
ste_dma40: move priority to separate field
ste_dma40: add variable to indicate valid dma_cfg
async_tx: make async_tx channel switching opt-in
move async raid6 test to lib/Kconfig.debug
dmaengine: Add Freescale i.MX1/21/27 DMA driver
intel_mid_dma: change the slave interface
intel_mid_dma: fix the WARN_ONs
intel_mid_dma: Add sg list support to DMA driver
intel_mid_dma: Allow DMAC2 to share interrupt
intel_mid_dma: Allow IRQ sharing
intel_mid_dma: Add runtime PM support
DMAENGINE: define a dummy filter function for ste_dma40
...
Currently, only two operating points: 160Mhz and 800Mhz.
the operating points are tested on babbage 3.0
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit c074512 (imx-esdhc: update devices registration) renamed
MX35_INT_MMC_SDHC2 to MX35_INT_ESDHC2 which broke expansion of the
MXC_INT_MMC_SDHC2 macro.
As (the only user of MXC_INT_MMC_SDHC2) is only used on
mx31 use the MX31 prefixed symbol to define its resources. Moreover to
reduce further confusion mxcsdhc_device0 is fixed accordingly and the MXC
prefixed symbols are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
This is only a partial revert of "ARM: mx3/mx31ads: fold board
header in its only user"
[commit ccfa7c2698)]
As some of the the board defines are also used in the cs89x0
ethernet driver by the i.MX31 ADS.
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>