Convert to net_device_ops and use internal net_device_stats in bnep
device.
Note: no need for bnep_net_ioctl since if ioctl is not set, then
dev_ifsioc handles it by returning -EOPNOTSUPP
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to use net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AF_CAN core delivered always cloned sk_buffs to the AF_CAN
protocols, although this was _only_ needed by the can-raw protocol.
With this (additionally documented) change, the AF_CAN core calls the
callback functions of the registered AF_CAN protocols with the original
(uncloned) sk_buff pointer and let's the can-raw protocol do the
skb_clone() itself which omits all unneeded skb_clone() calls for other
AF_CAN protocols.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO interfaces for hardware-assisted VLAN reception.
With this in place we're now at parity with LRO as far as the
interface is concerned. That is, you can now take any LRO driver
and convert it over to GRO.
As the CB memory clashes with GRO's use of CB, I've removed it
entirely by storing dev in skb->dev. This is OK because VLAN
gets called first thing in netif_receive_skb and skb->dev is
not used in between us calling netif_rx and netif_receive_skb
getting called.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously GRO's only entry point from the outside is through
napi_gro_receive and napi_gro_frags. These interfaces are for
device drivers.
This patch rearranges things to provide a new set of interfaces
for VLANs. These interfaces are for internal use only. The
VLAN code itself can then provide a set of entry points for
device drivers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (44 commits)
qlge: Fix sparse warnings for tx ring indexes.
qlge: Fix sparse warning regarding rx buffer queues.
qlge: Fix sparse endian warning in ql_hw_csum_setup().
qlge: Fix sparse endian warning for inbound packet control block flags.
qlge: Fix sparse warnings for byte swapping in qlge_ethool.c
myri10ge: print MAC and serial number on probe failure
pkt_sched: cls_u32: Fix locking in u32_change()
iucv: fix cpu hotplug
af_iucv: Free iucv path/socket in path_pending callback
af_iucv: avoid left over IUCV connections from failing connects
af_iucv: New error return codes for connect()
net/ehea: bitops work on unsigned longs
Revert "net: Fix for initial link state in 2.6.28"
tcp: Kill extraneous SPLICE_F_NONBLOCK checks.
tcp: don't mask EOF and socket errors on nonblocking splice receive
dccp: Integrate the TFRC library with DCCP
dccp: Clean up ccid.c after integration of CCID plugins
dccp: Lockless integration of CCID congestion-control plugins
qeth: get rid of extra argument after printk to dev_* conversion
qeth: No large send using EDDP for HiperSockets.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
inotify: fix type errors in interfaces
fix breakage in reiserfs_new_inode()
fix the treatment of jfs special inodes
vfs: remove duplicate code in get_fs_type()
add a vfs_fsync helper
sys_execve and sys_uselib do not call into fsnotify
zero i_uid/i_gid on inode allocation
inode->i_op is never NULL
ntfs: don't NULL i_op
isofs check for NULL ->i_op in root directory is dead code
affs: do not zero ->i_op
kill suid bit only for regular files
vfs: lseek(fd, 0, SEEK_CUR) race condition
New nodes are inserted in u32_change() under rtnl_lock() with wmb(),
so without tcf_tree_lock() like in other classifiers (e.g. cls_fw).
This isn't enough without rmb() on the read side, but on the other
hand adding such barriers doesn't give any savings, so the lock is
added instead.
Reported-by: m0sia <m0sia@plotinka.ru>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the iucv module is compiled in/loaded but no user is registered cpu
hot remove doesn't work. Reason for that is that the iucv cpu hotplug
notifier on CPU_DOWN_PREPARE checks if the iucv_buffer_cpumask would
be empty after the corresponding bit would be cleared. However the bit
was never set since iucv wasn't enable. That causes all cpu hot unplug
operations to fail in this scenario.
To fix this use iucv_path_table as an indicator wether iucv is enabled
or not.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free iucv path after iucv_path_sever() calls in iucv_callback_connreq()
(path_pending() iucv callback).
If iucv_path_accept() fails, free path and free/kill newly created socket.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certain types of AFIUCV socket connect failures IUCV connections
are left over. Add some cleanup-statements to avoid cluttered IUCV
connections.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the iucv_path_connect() call fails then return an error code that
corresponds to the iucv_path_connect() failure condition; instead of
returning -ECONNREFUSED for any failure.
This helps to improve error handling for user space applications
(e.g. inform the user that the z/VM guest is not authorized to
connect to other guest virtual machines).
The error return codes are based on those described in connect(2).
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 22604c8668.
We can't fix this issue in this way, because we now can try
to take the dev_base_lock rwlock as a writer in software interrupt
context and that is not allowed without major surgery elsewhere.
This initial link state problem needs to be solved in some other
way.
Signed-off-by: David S. Miller <davem@davemloft.net>
... and don't bother in callers. Don't bother with zeroing i_blocks,
while we are at it - it's already been zeroed.
i_mode is not worth the effort; it has no common default value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In splice TCP receive, the SPLICE_F_NONBLOCK flag is used
to compute the "timeo" value. So checking it again inside
of the main receive loop to trigger -EAGAIN processing is
entirely unnecessary.
Noticed by Jarek P. and Lennert Buytenhek.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, setting SPLICE_F_NONBLOCK on splice from a TCP socket
results in masking of EOF (RDHUP) and error conditions on the socket
by an -EAGAIN return. Move the NONBLOCK check in tcp_splice_read()
to be after the EOF and error checks to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch integrates the TFRC library, which is a dependency of CCID-3 (and
CCID-4), with the new use of CCIDs in the DCCP module.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up after integrating the CCID modules and, in addition,
* moves the if/else cases from ccid_delete() into ccid_hc_{tx,rx}_delete();
* removes the 'gfp' argument to ccid_new() - since it is always gfp_any().
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Arnaldo's earlier patch, this patch integrates the standardised
CCID congestion control plugins (CCID-2 and CCID-3) of DCCP with dccp.ko:
* enables a faster connection path by eliminating the need to always go
through the CCID registration lock;
* updates the implementation to use only a single array whose size equals
the number of configured CCIDs instead of the maximum (256);
* since the CCIDs are now fixed array elements, synchronization is no
longer needed, simplifying use and implementation.
CCID-2 is suggested as minimum for a basic DCCP implementation (RFC 4340, 10);
CCID-3 is a standards-track CCID supported by RFC 4342 and RFC 5348.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ca109491f6 ("hrtimer:
removing all ur callback modes") the hrtimer callbacks are processed
only in hardirq context.
This patch moves some functionality into tasklets to run in softirq
context.
Additionally some duplicated code was removed in bcm_rx_thr_flush()
and an avoidable memcpy was removed from bcm_rx_handler().
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kfree_skb instead of kfree for struct sk_buff pointers.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Michael Marineau <mike@marineau.org>
Commit b47300168e "Do not fire linkwatch
events until the device is registered." was made as a workaround for
drivers that call netif_carrier_off before registering the device.
Unfortunately this causes these drivers to incorrectly report their
link status as IF_OPER_UNKNOWN which can falsely set the IFF_RUNNING
flag when the interface is first brought up. This issues was
previously pointed out[1] but was dismissed saying that IFF_RUNNING is
not related to the link status. From my digging IFF_RUNNING, as
reported to userspace, is based on the link state. It is set based on
__LINK_STATE_START and IF_OPER_UP or IF_OPER_UNKNOWN. See [2], [3],
and [4]. (Whether or not the kernel has IFF_RUNNING set in flags is
not reported to user space so it may well be independent of the link,
I don't know if and when it may get set.)
The end result depends slightly depending on the driver. The the two I
tested were e1000e and b44. With e1000e if the system is booted
without a network cable attached the interface will falsely report
RUNNING when it is brought up causing NetworkManager to attempt to
start it and eventually time out. With b44 when the system is booted
with a network cable attached and brought up with dhcpcd it will time
out the first time.
The attached patch that will still set the operstate variable
correctly to IF_OPER_UP/DOWN/etc when linkwatch_fire_event is called
but then return rather than skipping the linkwatch_fire_event call
entirely as the previous fix did. (sorry it isn't inline, I don't have
a patch friendly email client at the moment)
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 4dec9b807b ("rfkill: strip pointless
notifier chain") removed the only user of rfkill_led_trigger() that was not
guarded by #ifdef CONFIG_RFKILL_LEDS. Therefore, move rfkill_led_trigger()
completely inside #ifdef CONFIG_RFKILL_LEDS and avoid the compile time
warning:
net/rfkill/rfkill.c:59: warning: 'rfkill_led_trigger' defined but not used
Signed-off-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows GRO to merge page frags (skb_shinfo(skb)->frags)
in one skb, rather than using the less efficient frag_list.
It also adds a new interface, napi_gro_frags to allow drivers
to inject page frags directly into the stack without allocating
an skb. This is intended to be the GRO equivalent for LRO's
lro_receive_frags interface.
The existing GSO interface can already handle page frags with
or without an appended frag_list so nothing needs to be changed
there.
The merging itself is rather simple. We store any new frag entries
after the last existing entry, without checking whether the first
new entry can be merged with the last existing entry. Making this
check would actually be easy but since no existing driver can
produce contiguous frags anyway it would just be mental masturbation.
If the total number of entries would exceed the capacity of a
single skb, we simply resort to using frag_list as we do now.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow GRO packets without frag_list at all, we need to
store the MSS in the packet itself. The obvious place is gso_size.
The only thing to watch out for is if the packet ends up not being
GRO then we need to clear gso_size before pushing the packet into
the stack.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to excellent diagnosis by Eduard Guzovsky.
The core problem is that on a network with lots of active
multicast traffic, the neighbour cache can fill up. If
we try to allocate a new route and thus neighbour cache
entry, the bog-standard GC attempt the neighbour layer does
in ineffective because route entries hold a reference
to the existing neighbour entries and GC can only liberate
entries with no references.
IPV4 already has a way to handle this, by doing a route cache
GC in such situations (when neigh attach returns -ENOBUFS).
So simply mimick this on the ipv6 side.
Tested-by: Eduard Guzovsky <eguzovsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin noted that line is unsigned so one test is unneccessary. Also
add a warning for another flaw I noticed while making this change.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add new LSM hooks for path-based checks. Call them on directory-modifying
operations at the points where we still know the vfsmount involved.
Signed-off-by: Kentaro Takeda <takedakn@nttdata.co.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toshiharu Harada <haradats@nttdata.co.jp>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (70 commits)
fs/nfs/nfs4proc.c: make nfs4_map_errors() static
rpc: add service field to new upcall
rpc: add target field to new upcall
nfsd: support callbacks with gss flavors
rpc: allow gss callbacks to client
rpc: pass target name down to rpc level on callbacks
nfsd: pass client principal name in rsc downcall
rpc: implement new upcall
rpc: store pointer to pipe inode in gss upcall message
rpc: use count of pipe openers to wait for first open
rpc: track number of users of the gss upcall pipe
rpc: call release_pipe only on last close
rpc: add an rpc_pipe_open method
rpc: minor gss_alloc_msg cleanup
rpc: factor out warning code from gss_pipe_destroy_msg
rpc: remove unnecessary assignment
NFS: remove unused status from encode routines
NFS: increment number of operations in each encode routine
NFS: fix comment placement in nfs4xdr.c
NFS: fix tabs in nfs4xdr.c
...
When we converted the protocol atomic counters such as the orphan
count and the total socket count deadlocks were introduced due to
the mismatch in BH status of the spots that used the percpu counter
operations.
Based on the diagnosis and patch by Peter Zijlstra, this patch
fixes these issues by disabling BH where we may be in process
context.
Reported-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In future all cpumask ops will only be valid (in general) for bit
numbers < nr_cpu_ids. So use that instead of NR_CPUS in iterators
and other comparisons.
This is always safe: no cpu number can be >= nr_cpu_ids, and
nr_cpu_ids is initialized to NR_CPUS at boot.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
cls_cgroup can't be compiled as a module, since it's not supported by
cgroup.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- It's better to use container_of() instead of casting cgroup_subsys_state *
to cgroup_cls_state *.
- Add helper function task_cls_state().
- Rename net_cls_state() to cgrp_cls_state().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a cgroup, an oops was triggered immediately. The cause
is wrong kfree() in cgrp_destroy().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During network namespace teardown we either move or delete
all of the network devices associated with a network namespace.
In the case of veth devices deleting one will also delete it's
pair device. If both devices are in the same network namespace
then for_each_netdev_safe is insufficient as next may point
to the second veth device we have deleted.
To avoid problems I do what we do in __rtnl_kill_links and
restart the scan of the device list, after we have deleted
a device.
Currently dev_change_netnamespace does not appear to suffer from
this problem, but wireless devices are also paired and likely
should be moved between network namespaces together. So I have
errored on the side of caution and restart the scan of the network
devices in that case as well.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
The initial skb may have been freed after napi_gro_complete in
napi_gro_receive if it was merged into an existing packet. Thus
we cannot check same_flow (which indicates whether it was merged)
after calling napi_gro_complete.
This patch fixes this by saving the same_flow status before the
call to napi_gro_complete.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent GRO patches introduced the NAPI removal of devices in
free_netdev. For drivers that can change the number of queues during
driver operation, the NAPI infrastructure doesn't allow the freeing and
re-addition of NAPI entities without reloading the driver.
This change reinitializes the dev_list in each NAPI struct on delete,
instead of just deleting it (and assigning the list pointers to POISON).
Drivers that wish to remove/re-add NAPI will need to re-initialize the
netdev napi_list after removing all NAPI instances, before re-adding NAPI
devices again.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a useless ret variable from the IPv4 ESP/UDP
decapsulation code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger