We can use a direct call for ipv4, so move the needed functions
to net/xfrm/xfrm_output.c and call them directly.
For ipv6 the indirection can be avoided as well but it will need
a bit more work -- to ease review it will be done in another patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds support for encapsulation of ESP over UDPv6. The code
is very similar to the IPv4 encapsulation implementation, and allows
to easily add espintcp on IPv6 as a follow-up.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
TCP encapsulation of IKE and IPsec messages (RFC 8229) is implemented
as a TCP ULP, overriding in particular the sendmsg and recvmsg
operations. A Stream Parser is used to extract messages out of the TCP
stream using the first 2 bytes as length marker. Received IKE messages
are put on "ike_queue", waiting to be dequeued by the custom recvmsg
implementation. Received ESP messages are sent to XFRM, like with UDP
encapsulation.
Some of this code is taken from the original submission by Herbert
Xu. Currently, only IPv4 is supported, like for UDP encapsulation.
Co-developed-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This will be used by TCP encapsulation to write packets to the encap
socket without holding the user socket's lock. Without this reinjection,
we're already holding the lock of the user socket, and then try to lock
the encap socket as well when we enqueue the encrypted packet.
While at it, add a BUILD_BUG_ON like we usually do for skb->cb, since
it's missing for struct xfrm_trans_cb.
Co-developed-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If IPsec is not configured, there is no reason to delay the inevitable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With the current implementation, phydev cannot be removed:
$ ip link add dummy type dummy
$ ip link add xfrm1 type xfrm dev dummy if_id 1
$ ip l d dummy
kernel:[77938.465445] unregister_netdevice: waiting for dummy to become free. Usage count = 1
Manage it like in ip tunnels, ie just keep the ifindex. Not that the side
effect, is that the phydev is now optional.
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Julien Floret <julien.floret@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The ifname is copied when the interface is created, but is never updated
later. In fact, this property is used only in one error message, where the
netdevice pointer is available, thus let's use it.
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
esp4_get_mtu and esp6_get_mtu are exactly the same, the only difference
is a single sizeof() (ipv4 vs. ipv6 header).
Merge both into xfrm_state_mtu() and remove the indirection.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Only a handful of xfrm_types exist, no need to have 512 pointers for them.
Reduces size of afinfo struct from 4k to 120 bytes on 64bit platforms.
Also, the unregister function doesn't need to return an error, no single
caller does anything useful with it.
Just place a WARN_ON() where needed instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm_prepare_input needs to lookup the state afinfo backend again to fetch
the address family ethernet protocol value.
There are only two address families, so a switch statement is simpler.
While at it, use u8 for family and proto and remove the owner member --
its not used anywhere.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No module dependency, placing this in xfrm_state.c avoids need for
an indirection.
This also removes the state spinlock -- I don't see why we would need
to hold it during sorting.
This in turn allows to remove the 'net' argument passed to
xfrm_tmpl_sort. Last, remove the EXPORT_SYMBOL, there are no modular
callers.
For the CONFIG_IPV6=m case, vmlinux size increase is about 300 byte.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
There is only one implementation of this function; just call it directly.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
same as previous patch: just place this in the caller, no need to
have an indirection for a structure initialization.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Simple initialization, handle it in the caller.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Pull timer updates from Ingo Molnar:
"This cycle had the following changes:
- Timer tracing improvements (Anna-Maria Gleixner)
- Continued tasklet reduction work: remove the hrtimer_tasklet
(Thomas Gleixner)
- Fix CPU hotplug remove race in the tick-broadcast mask handling
code (Thomas Gleixner)
- Force upper bound for setting CLOCK_REALTIME, to fix ABI
inconsistencies with handling values that are close to the maximum
supported and the vagueness of when uptime related wraparound might
occur. Make the consistent maximum the year 2232 across all
relevant ABIs and APIs. (Thomas Gleixner)
- various cleanups and smaller fixes"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Fix typos in comments
tick/broadcast: Fix warning about undefined tick_broadcast_oneshot_offline()
timekeeping: Force upper bound for setting CLOCK_REALTIME
timer/trace: Improve timer tracing
timer/trace: Replace deprecated vsprintf pointer extension %pf by %ps
timer: Move trace point to get proper index
tick/sched: Update tick_sched struct documentation
tick: Remove outgoing CPU from broadcast masks
timekeeping: Consistently use unsigned int for seqcount snapshot
softirq: Remove tasklet_hrtimer
xfrm: Replace hrtimer tasklet with softirq hrtimer
mac80211_hwsim: Replace hrtimer tasklet with softirq hrtimer
None of them have any external callers, make them static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No external dependencies, might as well handle this directly.
xfrm_afinfo_policy is now 40 bytes on x86_64.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
handle this directly, its only used by ipv6.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Only used by ipv4, we can read the fl4 tos value directly instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This structure is now only 4 bytes, so its more efficient
to cache a copy rather than its address.
No significant size difference in allmodconfig vmlinux.
With non-modular kernel that has all XFRM options enabled, this
series reduces vmlinux image size by ~11kb. All xfrm_mode
indirections are gone and all modes are built-in.
before (ipsec-next master):
text data bss dec filename
21071494 7233140 11104324 39408958 vmlinux.master
after this series:
21066448 7226772 11104324 39397544 vmlinux.patched
With allmodconfig kernel, the size increase is only 362 bytes,
even all the xfrm config options removed in this series are
modular.
before:
text data bss dec filename
15731286 6936912 4046908 26715106 vmlinux.master
after this series:
15731492 6937068 4046908 26715468 vmlinux
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
after previous changes, xfrm_mode contains no function pointers anymore
and all modules defining such struct contain no code except an init/exit
functions to register the xfrm_mode struct with the xfrm core.
Just place the xfrm modes core and remove the modules,
the run-time xfrm_mode register/unregister functionality is removed.
Before:
text data bss dec filename
7523 200 2364 10087 net/xfrm/xfrm_input.o
40003 628 440 41071 net/xfrm/xfrm_state.o
15730338 6937080 4046908 26714326 vmlinux
7389 200 2364 9953 net/xfrm/xfrm_input.o
40574 656 440 41670 net/xfrm/xfrm_state.o
15730084 6937068 4046908 26714060 vmlinux
The xfrm*_mode_{transport,tunnel,beet} modules are gone.
v2: replace CONFIG_INET6_XFRM_MODE_* IS_ENABLED guards with CONFIG_IPV6
ones rather than removing them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Adds an EXPORT_SYMBOL for afinfo_get_rcu, as it will now be called from
ipv6 in case of CONFIG_IPV6=m.
This change has virtually no effect on vmlinux size, but it reduces
afinfo size and allows followup patch to make xfrm modes const.
v2: mark if (afinfo) tests as likely (Sabrina)
re-fetch afinfo according to inner_mode in xfrm_prepare_input().
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
similar to previous patch: no external module dependencies,
so we can avoid the indirection by placing this in the core.
This change removes the last indirection from xfrm_mode and the
xfrm4|6_mode_{beet,tunnel}.c modules contain (almost) no code anymore.
Before:
text data bss dec hex filename
3957 136 0 4093 ffd net/xfrm/xfrm_output.o
587 44 0 631 277 net/ipv4/xfrm4_mode_beet.o
649 32 0 681 2a9 net/ipv4/xfrm4_mode_tunnel.o
625 44 0 669 29d net/ipv6/xfrm6_mode_beet.o
599 32 0 631 277 net/ipv6/xfrm6_mode_tunnel.o
After:
text data bss dec hex filename
5359 184 0 5543 15a7 net/xfrm/xfrm_output.o
171 24 0 195 c3 net/ipv4/xfrm4_mode_beet.o
171 24 0 195 c3 net/ipv4/xfrm4_mode_tunnel.o
172 24 0 196 c4 net/ipv6/xfrm6_mode_beet.o
172 24 0 196 c4 net/ipv6/xfrm6_mode_tunnel.o
v2: fold the *encap_add functions into xfrm*_prepare_output
preserve (move) output2 comment (Sabrina)
use x->outer_mode->encap, not inner
fix a build breakage on ppc (kbuild robot)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No external dependencies on any module, place this in the core.
Increase is about 1800 byte for xfrm_input.o.
The beet helpers get added to internal header, as they can be reused
from xfrm_output.c in the next patch (kernel contains several
copies of them in the xfrm{4,6}_mode_beet.c files).
Before:
text data bss dec filename
5578 176 2364 8118 net/xfrm/xfrm_input.o
1180 64 0 1244 net/ipv4/xfrm4_mode_beet.o
171 40 0 211 net/ipv4/xfrm4_mode_transport.o
1163 40 0 1203 net/ipv4/xfrm4_mode_tunnel.o
1083 52 0 1135 net/ipv6/xfrm6_mode_beet.o
172 40 0 212 net/ipv6/xfrm6_mode_ro.o
172 40 0 212 net/ipv6/xfrm6_mode_transport.o
1056 40 0 1096 net/ipv6/xfrm6_mode_tunnel.o
After:
text data bss dec filename
7373 200 2364 9937 net/xfrm/xfrm_input.o
587 44 0 631 net/ipv4/xfrm4_mode_beet.o
171 32 0 203 net/ipv4/xfrm4_mode_transport.o
649 32 0 681 net/ipv4/xfrm4_mode_tunnel.o
625 44 0 669 net/ipv6/xfrm6_mode_beet.o
172 32 0 204 net/ipv6/xfrm6_mode_ro.o
172 32 0 204 net/ipv6/xfrm6_mode_transport.o
599 32 0 631 net/ipv6/xfrm6_mode_tunnel.o
v2: pass inner_mode to xfrm_inner_mode_encap_remove to fix
AF_UNSPEC selector breakage (bisected by Benedict Wong)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
There are only two versions (tunnel and transport). The ip/ipv6 versions
are only differ in sizeof(iphdr) vs ipv6hdr.
Place this in the core and use x->outer_mode->encap type to call the
correct adjustment helper.
Before:
text data bss dec filename
15730311 6937008 4046908 26714227 vmlinux
After:
15730428 6937008 4046908 26714344 vmlinux
(about 117 byte increase)
v2: use family from x->outer_mode, not inner
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Same is input indirection. Only exception: we need to export
xfrm_outer_mode_output for pktgen.
Increases size of vmlinux by about 163 byte:
Before:
text data bss dec filename
15730208 6936948 4046908 26714064 vmlinux
After:
15730311 6937008 4046908 26714227 vmlinux
xfrm_inner_extract_output has no more external callers, make it static.
v2: add IS_ENABLED(IPV6) guard in xfrm6_prepare_output
add two missing breaks in xfrm_outer_mode_output (Sabrina Dubroca)
add WARN_ON_ONCE for 'call AF_INET6 related output function, but
CONFIG_IPV6=n' case.
make xfrm_inner_extract_output static
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No need for any indirection or abstraction here, both functions
are pretty much the same and quite small, they also have no external
dependencies.
xfrm_prepare_input can then be made static.
With allmodconfig build, size increase of vmlinux is 25 byte:
Before:
text data bss dec filename
15730207 6936924 4046908 26714039 vmlinux
After:
15730208 6936948 4046908 26714064 vmlinux
v2: Fix INET_XFRM_MODE_TRANSPORT name in is-enabled test (Sabrina Dubroca)
change copied comment to refer to transport and network header,
not skb->{h,nh}, which don't exist anymore. (Sabrina)
make xfrm_prepare_input static (Eyal Birger)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This will be useful to know if we're supposed to decode ipv4 or ipv6.
While at it, make the unregister function return void, all module_exit
functions did just BUG(); there is never a point in doing error checks
if there is no way to handle such error.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If an xfrmi is associated to a vrf layer 3 master device,
xfrm_policy_check() fails after traffic decapsulation. The input
interface is replaced by the layer 3 master device, and hence
xfrmi_decode_session() can't match the xfrmi anymore to satisfy
policy checking.
Extend ingress xfrmi lookup to honor the original layer 3 slave
device, allowing xfrm interfaces to operate within a vrf domain.
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In commit 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
I introduced a check for xfrm protocol, but according to Herbert
IPSEC_PROTO_ANY should only be used as a wildcard for lookup, so
it should be removed from validate_tmpl().
And, IPSEC_PROTO_ANY is expected to only match 3 IPSec-specific
protocols, this is why xfrm_state_flush() could still miss
IPPROTO_ROUTING, which leads that those entries are left in
net->xfrm.state_all before exit net. Fix this by replacing
IPSEC_PROTO_ANY with zero.
This patch also extracts the check from validate_tmpl() to
xfrm_id_proto_valid() and uses it in parse_ipsecrequest().
With this, no other protocols should be added into xfrm.
Fixes: 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
Reported-by: syzbot+0bf0519d6e0de15914fe@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Switch the timer to HRTIMER_MODE_SOFT, which executed the timer
callback in softirq context and remove the hrtimer_tasklet.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Link: https://lkml.kernel.org/r/20190301224821.29843-3-bigeasy@linutronix.de
xfrm_state_put() moves struct xfrm_state to the GC list
and schedules the GC work to clean it up. On net exit call
path, xfrm_state_flush() is called to clean up and
xfrm_flush_gc() is called to wait for the GC work to complete
before exit.
However, this doesn't work because one of the ->destructor(),
ipcomp_destroy(), schedules the same GC work again inside
the GC work. It is hard to wait for such a nested async
callback. This is also why syzbot still reports the following
warning:
WARNING: CPU: 1 PID: 33 at net/ipv6/xfrm6_tunnel.c:351 xfrm6_tunnel_net_exit+0x2cb/0x500 net/ipv6/xfrm6_tunnel.c:351
...
ops_exit_list.isra.0+0xb0/0x160 net/core/net_namespace.c:153
cleanup_net+0x51d/0xb10 net/core/net_namespace.c:551
process_one_work+0xd0c/0x1ce0 kernel/workqueue.c:2153
worker_thread+0x143/0x14a0 kernel/workqueue.c:2296
kthread+0x357/0x430 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
In fact, it is perfectly fine to bypass GC and destroy xfrm_state
synchronously on net exit call path, because it is in process context
and doesn't need a work struct to do any blocking work.
This patch introduces xfrm_state_put_sync() which simply bypasses
GC, and lets its callers to decide whether to use this synchronous
version. On net exit path, xfrm_state_fini() and
xfrm6_tunnel_net_exit() use it. And, as ipcomp_destroy() itself is
blocking, it can use xfrm_state_put_sync() directly too.
Also rename xfrm_state_gc_destroy() to ___xfrm_state_destroy() to
reflect this change.
Fixes: b48c05ab5d ("xfrm: Fix warning in xfrm6_tunnel_net_exit.")
Reported-and-tested-by: syzbot+e9aebef558e3ed673934@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove skb->sp and allocate secpath storage via extension
infrastructure. This also reduces sk_buff by 8 bytes on x86_64.
Total size of allyesconfig kernel is reduced slightly, as there is
less inlined code (one conditional atomic op instead of two on
skb_clone).
No differences in throughput in following ipsec performance tests:
- transport mode with aes on 10GB link
- tunnel mode between two network namespaces with aes and null cipher
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will reduce noise when skb->sp is removed later in this series.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_sec_path gains 'const' qualifier to avoid
xt_policy.c: 'skb_sec_path' discards 'const' qualifier from pointer target type
same reasoning as previous conversions: Won't need to touch these
spots anymore when skb->sp is removed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future patch will remove skb->sp pointer.
To reduce noise in those patches, move existing helper to
sk_buff and use it in more places to ease skb->sp replacement later.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can only return 0 (success) or -ENOMEM.
Change return value to a pointer to secpath struct.
This avoids direct access to skb->sp:
err = secpath_set(skb);
if (!err) ..
skb->sp-> ...
Becomes:
sp = secpath_set(skb)
if (!sp) ..
sp-> ..
This reduces noise in followup patch which is going to remove skb->sp.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to clean up indentation issue, remove an extraneous
space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Commit 565f0fa902 ("xfrm: use a dedicated slab cache for struct
xfrm_state") moved xfrm state objects to use their own slab cache.
However, it missed to adapt xfrm_user to use this new cache when
freeing xfrm states.
Fix this by introducing and make use of a new helper for freeing
xfrm_state objects.
Fixes: 565f0fa902 ("xfrm: use a dedicated slab cache for struct xfrm_state")
Reported-by: Pan Bian <bianpan2016@163.com>
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This adds inexact lists per destination network, stored in a search tree.
Inexact lookups now return two 'candidate lists', the 'any' policies
('any' destionations), and a list of policies that share same
daddr/prefix.
Next patch will add a second search tree for 'saddr:any' policies
so we can avoid placing those on the 'any:any' list too.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
At this time inexact policies are all searched in-order until the first
match is found. After removal of the flow cache, this resolution has
to be performed for every packetm resulting in major slowdown when
number of inexact policies is high.
This adds infrastructure to later sort inexact policies into a tree.
This only introduces a single class: any:any.
Next patch will add a search tree to pre-sort policies that
have a fixed daddr/prefixlen, so in this patch the any:any class
will still be used for all policies.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Switch packet-path lookups for inexact policies to rhashtable.
In this initial version, we now no longer need to search policies with
non-matching address family and type.
Next patch will add the if_id as well so lookups from the xfrm interface
driver only need to search inexact policies for that device.
Future patches will augment the hlist in each rhash bucket with a tree
and pre-sort policies according to daddr/prefix.
A single rhashtable is used. In order to avoid a full rhashtable walk on
netns exit, the bins get placed on a pernet list, i.e. we add almost no
cost for network namespaces that had no xfrm policies.
The inexact lists are kept in place, and policies are added to both the
per-rhash-inexact list and a pernet one.
The latter is needed for the control plane to handle migrate -- these
requests do not consider the if_id, so if we'd remove the inexact_list
now we would have to search all hash buckets and then figure
out which matching policy candidate is the most recent one -- this appears
a bit harder than just keeping the 'old' inexact list for this purpose.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
In order to remove performance impact of having the extra u32 in every
single flowi, this change removes the flowi_xfrm struct, prefering to
take the if_id as a method parameter where needed.
In the inbound direction, if_id is only needed during the
__xfrm_check_policy() function, and the if_id can be determined at that
point based on the skb. As such, xfrmi_decode_session() is only called
with the skb in __xfrm_check_policy().
In the outbound direction, the only place where if_id is needed is the
xfrm_lookup() call in xfrmi_xmit2(). With this change, the if_id is
directly passed into the xfrm_lookup_with_ifid() call. All existing
callers can still call xfrm_lookup(), which uses a default if_id of 0.
This change does not change any behavior of XFRMIs except for improving
overall system performance via flowi size reduction.
This change has been tested against the Android Kernel Networking Tests:
https://android.googlesource.com/kernel/tests/+/master/net/test
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
get_seconds() is deprecated because it can overflow on 32-bit
architectures. For the xfrm_state->lastused member, we treat the data
as a 64-bit number already, so we just need to use the right accessor
that works on both 32-bit and 64-bit machines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Kristian Evensen says:
In a project I am involved in, we are running ipsec (Strongswan) on
different mt7621-based routers. Each router is configured as an
initiator and has around ~30 tunnels to different responders (running
on misc. devices). Before the flow cache was removed (kernel 4.9), we
got a combined throughput of around 70Mbit/s for all tunnels on one
router. However, we recently switched to kernel 4.14 (4.14.48), and
the total throughput is somewhere around 57Mbit/s (best-case). I.e., a
drop of around 20%. Reverting the flow cache removal restores, as
expected, performance levels to that of kernel 4.9.
When pcpu xdst exists, it has to be validated first before it can be
used.
A negative hit thus increases cost vs. no-cache.
As number of tunnels increases, hit rate decreases so this pcpu caching
isn't a viable strategy.
Furthermore, the xdst cache also needs to run with BH off, so when
removing this the bh disable/enable pairs can be removed too.
Kristian tested a 4.14.y backport of this change and reported
increased performance:
In our tests, the throughput reduction has been reduced from around -20%
to -5%. We also see that the overall throughput is independent of the
number of tunnels, while before the throughput was reduced as the number
of tunnels increased.
Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds support for virtual xfrm interfaces.
Packets that are routed through such an interface
are guaranteed to be IPsec transformed or dropped.
It is a generic virtual interface that ensures IPsec
transformation, no need to know what happens behind
the interface. This means that we can tunnel IPv4 and
IPv6 through the same interface and support all xfrm
modes (tunnel, transport and beet) on it.
Co-developed-by: Lorenzo Colitti <lorenzo@google.com>
Co-developed-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Benedict Wong <benedictwong@google.com>
Tested-by: Antony Antony <antony@phenome.org>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
This patch adds the xfrm interface id as a lookup key
for xfrm states and policies. With this we can assign
states and policies to virtual xfrm interfaces.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Benedict Wong <benedictwong@google.com>
Tested-by: Benedict Wong <benedictwong@google.com>
Tested-by: Antony Antony <antony@phenome.org>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
We already support setting an output mark at the xfrm_state,
unfortunately this does not support the input direction and
masking the marks that will be applied to the skb. This change
adds support applying a masked value in both directions.
The existing XFRMA_OUTPUT_MARK number is reused for this purpose
and as it is now bi-directional, it is renamed to XFRMA_SET_MARK.
An additional XFRMA_SET_MARK_MASK attribute is added for setting the
mask. If the attribute mask not provided, it is set to 0xffffffff,
keeping the XFRMA_OUTPUT_MARK existing 'full mask' semantics.
Co-developed-by: Tobias Brunner <tobias@strongswan.org>
Co-developed-by: Eyal Birger <eyal.birger@gmail.com>
Co-developed-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Remove comparison of audit_enabled to magic numbers outside of audit.
Related: https://github.com/linux-audit/audit-kernel/issues/86
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
-----BEGIN PGP SIGNATURE-----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=10u6
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20180605' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"Another reasonable chunk of audit changes for v4.18, thirteen patches
in total.
The thirteen patches can mostly be broken down into one of four
categories: general bug fixes, accessor functions for audit state
stored in the task_struct, negative filter matches on executable
names, and extending the (relatively) new seccomp logging knobs to the
audit subsystem.
The main driver for the accessor functions from Richard are the
changes we're working on to associate audit events with containers,
but I think they have some standalone value too so I figured it would
be good to get them in now.
The seccomp/audit patches from Tyler apply the seccomp logging
improvements from a few releases ago to audit's seccomp logging;
starting with this patchset the changes in
/proc/sys/kernel/seccomp/actions_logged should apply to both the
standard kernel logging and audit.
As usual, everything passes the audit-testsuite and it happens to
merge cleanly with your tree"
[ Heh, except it had trivial merge conflicts with the SELinux tree that
also came in from Paul - Linus ]
* tag 'audit-pr-20180605' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: Fix wrong task in comparison of session ID
audit: use existing session info function
audit: normalize loginuid read access
audit: use new audit_context access funciton for seccomp_actions_logged
audit: use inline function to set audit context
audit: use inline function to get audit context
audit: convert sessionid unset to a macro
seccomp: Don't special case audited processes when logging
seccomp: Audit attempts to modify the actions_logged sysctl
seccomp: Configurable separator for the actions_logged string
seccomp: Separate read and write code for actions_logged sysctl
audit: allow not equal op for audit by executable
audit: add syscall information to FEATURE_CHANGE records
Recognizing that the audit context is an internal audit value, use an
access function to retrieve the audit context pointer for the task
rather than reaching directly into the task struct to get it.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: merge fuzz in auditsc.c and selinuxfs.c, checkpatch.pl fixes]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Use a macro, "AUDIT_SID_UNSET", to replace each instance of
initialization and comparison to an audit session ID.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
We need to make sure that all states are really deleted
before we check that the state lists are empty. Otherwise
we trigger a warning.
Fixes: baeb0dbbb5 ("xfrm6_tunnel: exit_net cleanup check added")
Reported-and-tested-by:syzbot+777bf170a89e7b326405@syzkaller.appspotmail.com
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently, driver registers it from pernet_operations::init method,
and this breaks modularity, because initialization of net namespace
and netdevice notifiers are orthogonal actions. We don't have
per-namespace netdevice notifiers; all of them are global for all
devices in all namespaces.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ran simple script to find/remove trailing whitespace and blank lines
at EOF because that kind of stuff git whines about and editors leave
behind.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ESN support to IPsec device offload.
Adding new xfrm device operation to synchronize device ESN.
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current XFRM code assumes that we've implemented the
xdo_dev_state_free() callback, even if it is meaningless to the driver.
This patch adds a check for it before calling, as done in other APIs,
to prevent a NULL function pointer kernel crash.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With support of async crypto operations in the GSO codepath
we have everything in place to allow GSO for local sockets.
This patch enables the GSO codepath.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch implements asynchronous crypto callbacks
and a backlog handler that can be used when IPsec
is done at layer 2 in the TX path. It also extends
the skb validate functions so that we can update
the driver transmit return codes based on async
crypto operation or to indicate that we queued the
packet in a backlog queue.
Joint work with: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We change the ESP GSO handlers to only segment the packets.
The ESP handling and encryption is defered to validate_xmit_xfrm()
where this is done for non GRO packets too. This makes the code
more robust and prepares for asynchronous crypto handling.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This is an old bugbear of mine:
https://www.mail-archive.com/netdev@vger.kernel.org/msg03894.html
By crafting special packets, it is possible to cause recursion
in our kernel when processing transport-mode packets at levels
that are only limited by packet size.
The easiest one is with DNAT, but an even worse one is where
UDP encapsulation is used in which case you just have to insert
an UDP encapsulation header in between each level of recursion.
This patch avoids this problem by reinjecting tranport-mode packets
through a tasklet.
Fixes: b05e106698 ("[IPV4/6]: Netfilter IPsec input hooks")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The first member of an IPSEC route bundle chain sets it's dst->path to
the underlying ipv4/ipv6 route that carries the bundle.
Stated another way, if one were to follow the xfrm_dst->child chain of
the bundle, the final non-NULL pointer would be the path and point to
either an ipv4 or an ipv6 route.
This is largely used to make sure that PMTU events propagate down to
the correct ipv4 or ipv6 route.
When we don't have the top of an IPSEC bundle 'dst->path == dst'.
Move it down into xfrm_dst and key off of dst->xfrm.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
XFRM bundle child chains look like this:
xdst1 --> xdst2 --> xdst3 --> path_dst
All of xdstN are xfrm_dst objects and xdst->u.dst.xfrm is non-NULL.
The final child pointer in the chain, here called 'path_dst', is some
other kind of route such as an ipv4 or ipv6 one.
The xfrm output path pops routes, one at a time, via the child
pointer, until we hit one which has a dst->xfrm pointer which
is NULL.
We can easily preserve the above mechanisms with child sitting
only in the xfrm_dst structure. All children in the chain
before we break out of the xfrm_output() loop have dst->xfrm
non-NULL and are therefore xfrm_dst objects.
Since we break out of the loop when we find dst->xfrm NULL, we
will not try to dereference 'dst' as if it were an xfrm_dst.
Signed-off-by: David S. Miller <davem@davemloft.net>
This will make a future change moving the dst->child pointer less
invasive.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Only IPSEC routes have a non-NULL dst->child pointer. And IPSEC
routes are identified by a non-NULL dst->xfrm pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replay detection bitmaps can't have negative length.
Comparisons with nla_len() are left signed just in case negative value
can sneak in there.
Propagate unsignedness for code size savings:
add/remove: 0/0 grow/shrink: 0/5 up/down: 0/-38 (-38)
function old new delta
xfrm_state_construct 1802 1800 -2
xfrm_update_ae_params 295 289 -6
xfrm_state_migrate 1345 1339 -6
xfrm_replay_notify_esn 349 337 -12
xfrm_replay_notify_bmp 345 333 -12
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Key lengths can't be negative.
Comparison with nla_len() is left signed just in case negative value
can sneak in there.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Key lengths can't be negative.
Comparison with nla_len() is left signed just in case negative value
can sneak in there.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Key lengths can't be negative.
Comparison with nla_len() is left signed just in case negative value
can sneak in there.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In conjunction with crypto offload [1], removing the ESP trailer by
hardware can potentially improve the performance by avoiding (1) a
cache miss incurred by reading the nexthdr field and (2) the necessity
to calculate the csum value of the trailer in order to keep skb->csum
valid.
This patch introduces the changes to the xfrm stack and merely serves
as an infrastructure. Subsequent patch to mlx5 driver will put this to
a good use.
[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg175733.html
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
On systems that use mark-based routing it may be necessary for
routing lookups to use marks in order for packets to be routed
correctly. An example of such a system is Android, which uses
socket marks to route packets via different networks.
Currently, routing lookups in tunnel mode always use a mark of
zero, making routing incorrect on such systems.
This patch adds a new output_mark element to the xfrm state and
a corresponding XFRMA_OUTPUT_MARK netlink attribute. The output
mark differs from the existing xfrm mark in two ways:
1. The xfrm mark is used to match xfrm policies and states, while
the xfrm output mark is used to set the mark (and influence
the routing) of the packets emitted by those states.
2. The existing mark is constrained to be a subset of the bits of
the originating socket or transformed packet, but the output
mark is arbitrary and depends only on the state.
The use of a separate mark provides additional flexibility. For
example:
- A packet subject to two transforms (e.g., transport mode inside
tunnel mode) can have two different output marks applied to it,
one for the transport mode SA and one for the tunnel mode SA.
- On a system where socket marks determine routing, the packets
emitted by an IPsec tunnel can be routed based on a mark that
is determined by the tunnel, not by the marks of the
unencrypted packets.
- Support for setting the output marks can be introduced without
breaking any existing setups that employ both mark-based
routing and xfrm tunnel mode. Simply changing the code to use
the xfrm mark for routing output packets could xfrm mark could
change behaviour in a way that breaks these setups.
If the output mark is unspecified or set to zero, the mark is not
set or changed.
Tested: make allyesconfig; make -j64
Tested: https://android-review.googlesource.com/452776
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch allows local sockets to make use of XFRM GSO code path.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
IPSec crypto offload depends on the protocol-specific
offload module (such as esp_offload.ko).
When the user installs an SA with crypto-offload, load
the offload module automatically, in the same way
that the protocol module is loaded (such as esp.ko)
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
retain last used xfrm_dst in a pcpu cache.
On next request, reuse this dst if the policies are the same.
The cache will not help with strict RR workloads as there is no hit.
The cache packet-path part is reasonably small, the notifier part is
needed so we do not add long hangs when a device is dismantled but some
pcpu xdst still holds a reference, there are also calls to the flush
operation when userspace deletes SAs so modules can be removed
(there is no hit.
We need to run the dst_release on the correct cpu to avoid races with
packet path. This is done by adding a work_struct for each cpu and then
doing the actual test/release on each affected cpu via schedule_work_on().
Test results using 4 network namespaces and null encryption:
ns1 ns2 -> ns3 -> ns4
netperf -> xfrm/null enc -> xfrm/null dec -> netserver
what TCP_STREAM UDP_STREAM UDP_RR
Flow cache: 14644.61 294.35 327231.64
No flow cache: 14349.81 242.64 202301.72
Pcpu cache: 14629.70 292.21 205595.22
UDP tests used 64byte packets, tests ran for one minute each,
value is average over ten iterations.
'Flow cache' is 'net-next', 'No flow cache' is net-next plus this
series but without this patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After rcu conversions performance degradation in forward tests isn't that
noticeable anymore.
See next patch for some numbers.
A followup patcg could then also remove genid from the policies
as we do not cache bundles anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-06-23
1) Use memdup_user to spmlify xfrm_user_policy.
From Geliang Tang.
2) Make xfrm_dev_register static to silence a sparse warning.
From Wei Yongjun.
3) Use crypto_memneq to check the ICV in the AH protocol.
From Sabrina Dubroca.
4) Remove some unused variables in esp6.
From Stephen Hemminger.
5) Extend XFRM MIGRATE to allow to change the UDP encapsulation port.
From Antony Antony.
6) Include the UDP encapsulation port to km_migrate announcements.
From Antony Antony.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XFRMA_ENCAP, UDP encapsulation port, to km_migrate announcement
to userland. Only add if XFRMA_ENCAP was in user migrate request.
Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Richard Guy Briggs <rgb@tricolour.ca>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add UDP encapsulation port to XFRM_MSG_MIGRATE using an optional
netlink attribute XFRMA_ENCAP.
The devices that support IKE MOBIKE extension (RFC-4555 Section 3.8)
could go to sleep for a few minutes and wake up. When it wake up the
NAT mapping could have expired, the device send a MOBIKE UPDATE_SA
message to migrate the IPsec SA. The change could be a change UDP
encapsulation port, IP address, or both.
Reported-by: Paul Wouters <pwouters@redhat.com>
Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Richard Guy Briggs <rgb@tricolour.ca>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In commit d77e38e612 ("xfrm: Add an IPsec hardware offloading API") we
make xfrm_device.o only compiled when enable option CONFIG_XFRM_OFFLOAD.
But this will make xfrm_dev_event() missing if we only enable default XFRM
options.
Then if we set down and unregister an interface with IPsec on it. there
will no xfrm_garbage_collect(), which will cause dev usage count hold and
get error like:
unregister_netdevice: waiting for <dev> to become free. Usage count = 4
Fixes: d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When CONFIG_XFRM_SUB_POLICY=y, xfrm_dst stores a copy of the flowi for
that dst. Unfortunately, the code that allocates and fills this copy
doesn't care about what type of flowi (flowi, flowi4, flowi6) gets
passed. In multiple code paths (from raw_sendmsg, from TCP when
replying to a FIN, in vxlan, geneve, and gre), the flowi that gets
passed to xfrm is actually an on-stack flowi4, so we end up reading
stuff from the stack past the end of the flowi4 struct.
Since xfrm_dst->origin isn't used anywhere following commit
ca116922af ("xfrm: Eliminate "fl" and "pol" args to
xfrm_bundle_ok()."), just get rid of it. xfrm_dst->partner isn't used
either, so get rid of that too.
Fixes: 9d6ec93801 ("ipv4: Use flowi4 in public route lookup interfaces.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When we do IPsec offloading, we need a fallback for
packets that were targeted to be IPsec offloaded but
rerouted to a device that does not support IPsec offload.
For that we add a function that checks the offloading
features of the sending device and and flags the
requirement of a fallback before it calls the IPsec
output function. The IPsec output function adds the IPsec
trailer and does encryption if needed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds all the bits that are needed to do
IPsec hardware offload for IPsec states and ESP packets.
We add xfrmdev_ops to the net_device. xfrmdev_ops has
function pointers that are needed to manage the xfrm
states in the hardware and to do a per packet
offloading decision.
Joint work with:
Ilan Tayari <ilant@mellanox.com>
Guy Shapiro <guysh@mellanox.com>
Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds a gso_segment and xmit callback for the
xfrm_mode and implement these functions for tunnel and
transport mode.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We add a struct xfrm_type_offload so that we have the offloaded
codepath separated to the non offloaded codepath. With this the
non offloade and the offloaded codepath can coexist.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Current addr4_match() code has special test for /0 prefixes because of
standard required undefined behaviour. However, it is possible to omit
it on 64-bit because shifting can be done within a 64-bit register and
then truncated to the expected value (which is 0 mask).
Implicit truncation by htonl() fits nicely into R32-within-R64 model
on x86-64.
Space savings: none (coincidence)
Branch savings: 1
Before:
movzx eax,BYTE PTR [rdi+0x2a] # ->prefixlen_d
test al,al
jne xfrm_selector_match + 0x23f
...
movzx eax,BYTE PTR [rbx+0x2b] # ->prefixlen_s
test al,al
je xfrm_selector_match + 0x1c7
After (no branches):
mov r8d,0x20
mov rdx,0xffffffffffffffff
mov esi,DWORD PTR [rsi+0x2c]
mov ecx,r8d
sub cl,BYTE PTR [rdi+0x2a]
xor esi,DWORD PTR [rbx]
mov rdi,rdx
xor eax,eax
shl rdi,cl
bswap edi
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
x86_64 is zero-extending arch so "unsigned int" is preferred over "int"
for address calculations and extending to size_t.
Space savings:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-24 (-24)
function old new delta
xfrm_state_walk 708 696 -12
xfrm_selector_match 918 906 -12
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Florian Westphal