The only supported bus for the R-Car CSI-2 driver is CSI-2 DPHY, specify
this before parsing the fwnode.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the fwnode_graph_get_endpoint_by_id() interface instead of
of_graph_get_endpoint_by_regs() to fetch the fwnode. This saves
translating between a device_node and fwnode_handle.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Extend the list of supported formats to include all RGB layouts of RAW8.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2H (R8A774E1) SoC.
The CSI-2 module of RZ/G2H is similar to R-Car H3.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_async_notifier_add_subdev() requires the asd to be allocated
dynamically, but the rcar-csi2 driver embeds it in the rcar_csi2
structure. This causes memory corruption when the notifier is destroyed
at remove time with v4l2_async_notifier_cleanup().
Fix this issue by registering the asd with
v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically
internally.
Fixes: 769afd212b ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the newly introduced get_mbus_config() subdevice pad operation to
retrieve the remote subdevice MIPI CSI-2 bus configuration and configure
the number of active data lanes accordingly.
In order to be able to call the remote subdevice operation cache the
index of the remote pad connected to the single CSI-2 input port.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since the driver was picked-up the starting of the PHY have changed
quiet a bit. An artifact of these changes is the now poorly named
callback confirm_start(). It used to confirm start of the PHY but now
performs post PHY start initialization, rename it to phy_post_init() to
reflect this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds support for MEDIA_BUS_FMT_SRGGB8_1X8 format for CSI2
input.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to latest H/W manual v1.50, the description of channel
number in the VCDT/VCDT2 register is decremented by one.
Therefore, this patch fixes it about comment.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2N(R8A774B1) SoC.
The CSI-2 module of RZ/G2N is similar to R-Car M3-N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Depending on which video standard is used the driver needs to setup the
hardware to correctly handle fields. If stream is identified as NTSC
or PAL setup field detection and propagate the field detection signal.
Later versions of the datasheet have been updated to make it clear
that FLD register should be set to 0 when dealing with non-interlaced
field formats.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Restart the CSI-2 link if the CSI-2 receiver detects an error during
reception. The driver did nothing when a link error happened and the
data flow simply stopped without the user knowing why.
Change the driver to try and recover from errors by restarting the link
and informing the user that something is not right. For obvious reasons
it's not possible to recover from all errors (video source disconnected
for example) but in such cases the user is at least informed of the
error and the same behavior of the stopped data flow is retained.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later datasheet versions (rev 1.00) clarifies that the FLD register
should be set after LINKCNT.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Latest information from hardware engineers reveals that H3 ES2 and ES3
behave differently when working with link speeds bellow 250 Mpbs.
Add a SoC match for H3 ES2.* and use the correct startup sequence.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The latest datasheet (rev 1.50) updates the start procedure for V3M and
E3. Update the driver to match these changes.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later versions of the datasheet updates the reset procedure to more
closely resemble the standby mode. Update the driver to enter and exit
the standby mode instead of resetting the hardware before and after
streaming is started and stopped. This replaces the software reset
(SRST.SRST) control.
While at it break out the full start and stop procedures from
rcsi2_s_stream() into the existing helper functions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2M(r8a774a1) SoC.
The CSI-2 module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to the RZ/G2 User's manual, RZ/G2E and R-Car E3 CSI-2
blocks are identical, therefore use R-Car E3 definitions to add
RZ/G2E support.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The PHTW selection algorithm implemented in rcsi2_phtw_write_mbps() checks for
lower bound of the interval used to match the desired bandwidth. Use that
in place of the currently used upper bound.
Fixes: 10c08812fe ("media: rcar: rcar-csi2: Update V3M/E3 PHTW tables")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the R-Car V3H (AKA R8A77980) SoC support to the R-Car CSI2 driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The R-Car CSI-2 interface has a number of selectable 'channels' that
provides pixel data to the VINs during image acquisition.
Each channel can be used to match a CSI-2 data type and a CSI-2 virtual
channel to be routed to output path.
Different SoCs have different number of channels, with R-Car E3 being the
notable exception supporting only 2 of them.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for R-Car E3 R8A77965 to R-Car CSI-2 driver.
Based on the experimental patch from Magnus Damm.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint
flags as well as the bus type. Setting bus type to zero will continue to
guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media
bus enum.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Switch all media platform drivers to call v4l2_async_notifier_add_subdev()
to add asd's to a notifier, in place of referencing the notifier->subdevs[]
array. These drivers also must now call v4l2_async_notifier_init() before
adding asd's to their notifiers.
There may still be cases where a platform driver maintains a list of
asd's that is a duplicate of the notifier asd_list, in which case its
possible the platform driver list can be removed, and can reference the
notifier asd_list instead. One example of where a duplicate list has
been removed in this patch is xilinx-vipp.c. If there are such cases
remaining, those drivers should be optimized to remove the duplicate
platform driver asd lists.
None of the changes to the platform drivers in this patch have been
tested. Verify that the async subdevices needed by the platform are
bound at load time, and that the driver unloads and reloads correctly
with no memory leaking of asd objects.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Latest errata document updates the start procedure for V3M. This change
in addition to adhering to the datasheet update fixes capture on early
revisions of V3M.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of failing the set_fmt() if a unsupported format is requested
set a default one and return the changed format to the user.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A V4L2 driver for Renesas R-Car MIPI CSI-2 receiver. The driver
supports the R-Car Gen3 SoCs where separate CSI-2 hardware blocks are
connected between the video sources and the video grabbers (VIN).
Driver is based on a prototype by Koji Matsuoka in the Renesas BSP.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Niklas Söderlund