For compatibility reasons the irq remapping code for the AMD
IOMMU used the same per-irq data structure as the Intel
implementation. Now that support for the AMD specific data
structure is upstream we can use this one instead.
Reviewed-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This function was intended as a fall-back if the map_sg
function is called for a device not mapped by the IOMMU.
Since the AMD IOMMU driver uses per-device dma_ops this can
never happen. So this function isn't needed anymore.
Reviewed-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Current driver does not clear the IOMMU event log interrupt bit
in the IOMMU status register after processing an interrupt.
This causes the IOMMU hardware to generate event log interrupt only once.
This has been observed in both IOMMU v1 and V2 hardware.
This patch clears the bit by writing 1 to bit 1 of the IOMMU
status register (MMIO Offset 2020h)
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Here are some fixes which have collected since Linux v3.9-rc1. The most
important one fixes a long-standing regressen which make re-hotplugged
devices unusable when AMD IOMMU is used. The other patches fix build
issues (build regression on OMAP and a section mismatch). One patch just
removes a duplicate header include.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/K5U
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Here are some fixes which have collected since Linux v3.9-rc1.
The most important one fixes a long-standing regressen which make
re-hotplugged devices unusable when AMD IOMMU is used.
The other patches fix build issues (build regression on OMAP and a
section mismatch). One patch just removes a duplicate header include."
* tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Make sure dma_ops are set for hotplug devices
x86, io_apic: remove duplicated include from irq_remapping.c
iommu: OMAP: build only on OMAP2+
amd_iommu_init: remove __init from amd_iommu_erratum_746_workaround
There is a bug introduced with commit 27c2127 that causes
devices which are hot unplugged and then hot-replugged to
not have per-device dma_ops set. This causes these devices
to not function correctly. Fixed with this patch.
Cc: stable@vger.kernel.org
Reported-by: Andreas Degert <andreas.degert@googlemail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The OMAP IOMMU driver intentionally fails to build on OMAP1
platforms, so we should not allow enabling it there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: iommu@lists.linux-foundation.org
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
commit 318fe78 ("IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround")
added amd_iommu_erratum_746_workaround and it's marked as __init, which is wrong
WARNING: drivers/iommu/built-in.o(.text+0x639c): Section mismatch in reference from the function iommu_init_pci() to the function .init.text:amd_iommu_erratum_746_workaround()
The function iommu_init_pci() references
the function __init amd_iommu_erratum_746_workaround().
This is often because iommu_init_pci lacks a __init
annotation or the annotation of amd_iommu_erratum_746_workaround is wrong.
Signed-off-by: Nikola Pajkovsky <npajkovs@redhat.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The number of DMA fault reasons in intel's document are from 1
to 0xD, but in dmar.c fault reason 0xD is not printed out.
In this document:
"Intel Virtualization Technology for Directed I/O Architecture Specification"
http://download.intel.com/technology/computing/vptech/Intel(r)_VT_for_Direct_IO.pdf
Chapter 4. Support For Device-IOTLBs
Table 6. Unsuccessful Translated Requests
There is fault reason for 0xD not listed in kernel:
Present context-entry used to process translation request
specifies blocking of Translation Requests (Translation Type (T)
field value not equal to 01b).
This patch adds reason 0xD as well.
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Donald Dutile <ddutile@redhat.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Hannes Reinecke <hare@suse.de>
Link: http://lkml.kernel.org/r/1362537797-6034-1-git-send-email-zhen-hual@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Besides some fixes and cleanups in the code there are three more
important changes to point out this time:
* New IOMMU driver for the ARM SHMOBILE platform
* An IOMMU-API extension for non-paging IOMMUs (required for
upcoming PAMU driver)
* Rework of the way the Tegra IOMMU driver accesses its
registetrs - register windows are easier to extend now.
There are also a few changes to non-iommu code, but that is acked by the
respective maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRK0gMAAoJECvwRC2XARrjHAwQANIJjqgZECxqx/MuAfmvkvA0
gRvlqBh/LWQhm/PlkpvqTMq7YY9kH1sxk+UD32oJok3XnScQWfcrJNmpijLo9/9Z
XyMTXQrGX0X+LWAXLIBXrlbV37mztHFEVxYrO+jiEGKP8+153sguPvmu0y6wC2AZ
RhsrVftDE7OIqdTGo8+ORCKOg7ZXNJ04hER4vW8I+0LLP1m6nnHXSKZ4E6Vmtc9K
YgfcwwsduYOkboMK5S0XLl58Xqiq53iXw3R+wSFIsFVVQ9Zp5yZzUGphvSQvDOBc
fX01M+Ouu+bT5U2DlDmYCnL3K14Mr7TqlH78Loq3w6yHRm1fxQoiF5vm98ZAmFde
nU6WCJNks0z+hIlkdIlrLgvBd8nWubGOtU3EfhzseawF1WexIusTqO4Fkp+rNJk0
wZ8h2ATUCch17BE8O794lCQuOwHQ6q7JcQmVz2GPJ83GEvQW1svKzzPIPBm0yLW3
hCS9T9O+Bic0Bx+L7QXu5D1aRxJskJUPnINVirfSUXb0vVLb/U9jGNgITf2A9XCl
p5z0i4RriDwCzg9917U4ZvjYbf3rjdMRwJ5TAxNqRrooMbGvOTZCJzIjujv82Adp
BDm8HZx3FZP/8S5hfE5Ahr4gaNle8jnO53G6jKkjDuSG6DP+XMEj82oSJ/M+Rnld
nCvEUi0bXhwHOOfdmgNU
=G4Ot
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU Updates from Joerg Roedel:
"Besides some fixes and cleanups in the code there are three more
important changes to point out this time:
* New IOMMU driver for the ARM SHMOBILE platform
* An IOMMU-API extension for non-paging IOMMUs (required for
upcoming PAMU driver)
* Rework of the way the Tegra IOMMU driver accesses its
registetrs - register windows are easier to extend now.
There are also a few changes to non-iommu code, but that is acked by
the respective maintainers."
* tag 'iommu-updates-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (23 commits)
iommu/tegra: assume CONFIG_OF in SMMU driver
iommu/tegra: assume CONFIG_OF in gart driver
iommu/amd: Remove redundant NULL check before dma_ops_domain_free().
iommu/amd: Initialize device table after dma_ops
iommu/vt-d: Zero out allocated memory in dmar_enable_qi
iommu/tegra: smmu: Fix incorrect mask for regbase
iommu/exynos: Make exynos_sysmmu_disable static
ARM: mach-shmobile: r8a7740: Add IPMMU device
ARM: mach-shmobile: sh73a0: Add IPMMU device
ARM: mach-shmobile: sh7372: Add IPMMU device
iommu/shmobile: Add iommu driver for Renesas IPMMU modules
iommu: Add DOMAIN_ATTR_WINDOWS domain attribute
iommu: Add domain window handling functions
iommu: Implement DOMAIN_ATTR_PAGING attribute
iommu: Check for valid pgsize_bitmap in iommu_map/unmap
iommu: Make sure DOMAIN_ATTR_MAX is really the maximum
iommu/tegra: smmu: Change SMMU's dependency on ARCH_TEGRA
iommu/tegra: smmu: Use helper function to check for valid register offset
iommu/tegra: smmu: Support variable MMIO ranges/blocks
iommu/tegra: Add missing spinlock initialization
...
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Pull x86/apic changes from Ingo Molnar:
"Main changes:
- Multiple MSI support added to the APIC, PCI and AHCI code - acked
by all relevant maintainers, by Alexander Gordeev.
The advantage is that multiple AHCI ports can have multiple MSI
irqs assigned, and can thus spread to multiple CPUs.
[ Drivers can make use of this new facility via the
pci_enable_msi_block_auto() method ]
- x86 IOAPIC code from interrupt remapping cleanups from Joerg
Roedel:
These patches move all interrupt remapping specific checks out of
the x86 core code and replaces the respective call-sites with
function pointers. As a result the interrupt remapping code is
better abstraced from x86 core interrupt handling code.
- Various smaller improvements, fixes and cleanups."
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess
x86, kvm: Fix intialization warnings in kvm.c
x86, irq: Move irq_remapped out of x86 core code
x86, io_apic: Introduce eoi_ioapic_pin call-back
x86, msi: Introduce x86_msi.compose_msi_msg call-back
x86, irq: Introduce setup_remapped_irq()
x86, irq: Move irq_remapped() check into free_remapped_irq
x86, io-apic: Remove !irq_remapped() check from __target_IO_APIC_irq()
x86, io-apic: Move CONFIG_IRQ_REMAP code out of x86 core
x86, irq: Add data structure to keep AMD specific irq remapping information
x86, irq: Move irq_remapping_enabled declaration to iommu code
x86, io_apic: Remove irq_remapping_enabled check in setup_timer_IRQ0_pin
x86, io_apic: Move irq_remapping_enabled checks out of check_timer()
x86, io_apic: Convert setup_ioapic_entry to function pointer
x86, io_apic: Introduce set_affinity function pointer
x86, msi: Use IRQ remapping specific setup_msi_irqs routine
x86, hpet: Introduce x86_msi_ops.setup_hpet_msi
x86, io_apic: Introduce x86_io_apic_ops.print_entries for debugging
x86, io_apic: Introduce x86_io_apic_ops.disable()
x86, apic: Mask IO-APIC and PIC unconditionally on LAPIC resume
...
We already have the quirk entry for the mobile platform, but also
reports on some desktop versions. So be paranoid and set it
everywhere.
References: http://www.mail-archive.com/dri-devel@lists.freedesktop.org/msg33138.html
Cc: stable@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Sankaran, Rajesh" <rajesh.sankaran@intel.com>
Reported-and-tested-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tegra only supports, and always enables, device tree. Remove all ifdefs
for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Tegra only supports, and always enables, device tree. Remove all ifdefs
for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
dma_ops_domain_free on a NULL pointer is a no-op, so the NULL check in
amd_iommu_init_dma_ops() can be removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
When dma_ops are initialized the unity mappings are
created. The init_device_table_dma() function makes sure DMA
from all devices is blocked by default. This opens a short
window in time where DMA to unity mapped regions is blocked
by the IOMMU. Make sure this does not happen by initializing
the device table after dma_ops.
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
kmemcheck complained about the use of uninitialized memory.
Fix by using kzalloc instead of kmalloc.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This fixes kernel crash because of BUG() in register address
validation.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
'exynos_sysmmu_disable' is used only in this file and can be made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This is the Renesas IPMMU driver and IOMMU API implementation.
The IPMMU module supports the MMU function and the PMB function. The
MMU function provides address translation by pagetable compatible with
ARMv6. The PMB function provides address translation including
tile-linear translation. This patch implements the MMU function.
The iommu driver does not register a platform driver directly because:
- the register space of the MMU function and the PMB function
have a common register (used for settings flush), so they should ideally
have a way to appropriately share this register.
- the MMU function uses the IOMMU API while the PMB function does not.
- the two functions may be used independently.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add the iommu_domain_window_enable() and iommu_domain_window_disable()
functions to the IOMMU-API. These functions will be used to setup
domains that are based on subwindows and not on paging.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This attribute of a domain can be queried to find out if the
domain supports setting up page-tables using the iommu_map()
and iommu_unmap() functions.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
In case the page-size bitmap is zero the code path in
iommu_map and iommu_unmap is undefined. Make it defined and
return -ENODEV in this case.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Theoretically TEGRA_IOMMU_SMMU depends on ARCH_TEGRA_3x_SOC and
ARCH_TEGRA_114_SOC only. This patch allows a Tegra20 only kernel to
enable SMMU(Tegra20 doesn't have a SMMU), which could avoid editing
this Kconfig entry every time we add a new chip later.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Do not repeat the checking loop in the read and write
functions. Use a single helper function for that check and
call it in both accessors.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Presently SMMU registers are located in discontiguous 3 blocks. They
are interleaved by MC registers. Ideally SMMU register blocks should
be in an independent one block, but it is too late to change this H/W
design. In the future Tegra chips over some generations, it is
expected that some of register block "size" can be extended towards
the end and also more new register blocks will be added at most a few
blocks. The starting address of each existing block won't change. This
patch allocates multiple number of register blocks dynamically based
on the info passed from DT. Those ranges are verified in the
accessors{read,write}. This may sacrifice some performance because a
new accessors prevents compiler optimization of a fixed size register
offset calculation. Since SMMU register accesses are not so frequent,
this would be acceptable. This patch is necessary to unify
"tegra-smmu.ko" over some Tegra SoC generations.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Current kernels print this on my Dell server:
------------[ cut here ]------------
WARNING: at drivers/iommu/intel_irq_remapping.c:542
intel_enable_irq_remapping+0x7b/0x27e()
Hardware name: PowerEdge R620
Your BIOS is broken and requested that x2apic be disabled
This will leave your machine vulnerable to irq-injection attacks
Use 'intremap=no_x2apic_optout' to override BIOS request
[...]
Enabled IRQ remapping in xapic mode
x2apic not enabled, IRQ remapping is in xapic mode
This is inconsistent with itself -- interrupt remapping is *on*.
Fix the mess by making the warnings say what they mean and my
making sure that compatibility format interrupts (the dangerous
ones) are disabled if x2apic is present regardless of BIOS
settings.
With this patch applied, the output is:
Your BIOS is broken and requested that x2apic be disabled.
This will slightly decrease performance.
Use 'intremap=no_x2apic_optout' to override BIOS request.
Enabled IRQ remapping in xapic mode
x2apic not enabled, IRQ remapping is in xapic mode
This should make us as or more secure than we are now and
replace a rather scary warning with a much less scary warning on
silly but functional systems.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Link: http://lkml.kernel.org/r/2011b943a886fd7c46079eb10bc24fc130587503.1359759303.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull drm fixes from Dave Airlie:
"Intel, radeon and exynos fixes. Nothing too major or wierd: one dmar
fix and a radeon cursor corruption, along with misc exynos fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (21 commits)
drm/exynos: add check for the device power status
drm/exynos: Make 'drm_hdmi_get_edid' static
drm/exynos: fimd and ipp are broken on multiplatform
drm/exynos: don't include plat/gpio-cfg.h
drm/exynos: Remove "internal" interrupt handling
drm/exynos: Add missing static specifiers in exynos_drm_rotator.c
drm/exynos: Replace mdelay with usleep_range
drm/exynos: Make ipp_handle_cmd_work static
drm/exynos: Make g2d_userptr_get_dma_addr static
drm/exynos: consider DMA_NONE flag to dmabuf import
drm/exynos: free sg object if dma_map_sg is failed
drm/exynos: added validation of edid for vidi connection
drm/exynos: let drm handle edid allocations
drm/radeon: Enable DMA_IB_SWAP_ENABLE on big endian hosts.
drm/radeon: fix a rare case of double kfree
radeon_display: Use pointer return error codes
drm/radeon: fix cursor corruption on DCE6 and newer
drm/i915: dump UTS_RELEASE into the error_state
iommu/intel: disable DMAR for g4x integrated gfx
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
...
The IOMMU may stop processing page translations due to a perceived lack
of credits for writing upstream peripheral page service request (PPR)
or event logs. If the L2B miscellaneous clock gating feature is enabled
the IOMMU does not properly register credits after the log request has
completed, leading to a potential system hang.
BIOSes are supposed to disable L2B micellaneous clock gating by setting
L2_L2B_CK_GATE_CONTROL[CKGateL2BMiscDisable](D0F2xF4_x90[2]) = 1b. This
patch corrects that for those which do not enable this workaround.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The pointer obj is dereferenced in line 146 and 149 respectively, so it is not
necessary to check null again in line 149 and 175. And I have checked that all
the callers of these two functions guarantee the parameter obj passed is not
null.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The irq_remapped function is only used in IOMMU code after
the last patch. So move its definition there too.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This callback replaces the old __eoi_ioapic_pin function
which needs a special path for interrupt remapping.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This call-back points to the right function for initializing
the msi_msg structure. The old code for msi_msg generation
was split up into the irq-remapped and the default case.
The irq-remapped case just calls into the specific Intel or
AMD implementation when the device is behind an IOMMU.
Otherwise the default function is called.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function does irq-remapping specific interrupt setup
like modifying the chip defaults.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The function is called unconditionally now in IO-APIC code
removing another irq_remapped() check from x86 core code.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Move all the code to either to the header file
asm/irq_remapping.h or to drivers/iommu/.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Remove the last left-over from this flag from x86 code.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Move these checks to IRQ remapping code by introducing the
panic_on_irq_remap() function.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This pointer is changed to a different function when IRQ
remapping is enabled.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
With interrupt remapping a special function is used to
change the affinity of an IO-APIC interrupt. Abstract this
with a function pointer.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Use seperate routines to setup MSI IRQs for both
irq_remapping_enabled cases.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function pointer can be overwritten by the IRQ
remapping code. The irq_remapping_enabled check can be
removed from default_setup_hpet_msi.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Joerg Roedel