Based on the normalized pattern:
this file is licensed under the terms of the gnu general public
license version 2 this program is licensed as is without any warranty
of any kind whether express or implied
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PRU-ICSS1 instance on AM437x SoCs has a MDIO sub-module that
can be used to control external PHYs associated with the Industrial
Ethernet peripherals within the PRUSS. The MDIO module used within
this PRU-ICSS is an instance of the MDIO Controller used in TI
Davinci SoCs. The same bus frequency of 1 MHz is chosen as the
regular MDIO node. Note that there is no MDIO node added to the
smaller PRU-ICSS0 instance as the MDIO pins are not pinned out.
The node is added and enabled in the common am4372.dtsi file by
default, and disabled in all the existing AM437x board dts files.
This node needs pinctrl lines, and so should be enabled only on
boards where they are actually wired and pinned out for PRUSS
Ethernet. Any new board dts file should disable these if they
are not sure.
Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: fix reg address, add commit description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM4376+ SoCs have a second smaller PRU-ICSS subsystem (PRUSS0) in
addition to the primary PRUSS1 instance. The PRUSS0 has less DRAM
per PRU, and no Shared DRAM among other minor differences. The IEP
and MII_RT modules even though present within the IP are not pinned
out.
This PRUSS0 instance has a weird SoC integration. It shares the same
L3 OCP interconnect interface with PRUSS1, and also shares its reset
line and clocks. Any external accesses from PRUSS0 requires the PRUSS1's
PRUSS_SYSCFG register to be programmed properly. That said, it is its
own IP instance (a cut-down version), and so it has been added as an
independent node (sibling node to PRUSS1 node) and a child node of the
corresponding PRUSS target module interconnect node. This allows the
PRUSS0 instance to be enabled/disabled independently of the PRUSS1
instance.
The nodes are added under the corresponding interconnect target module
node in the common am4372 dtsi file. The PRU-ICSS instances are not
supported on AM4372 SoC though in the AM437x family, so the interconnect
target module node should be disabled in any derivative board dts file that
uses AM4372 SoCs. The individual PRUSS node can be disabled in the
corresponding board dts file if desired.
The default names for the firmware images for each PRU core are defined
as follows (these can be adjusted either in derivative board dts files or
through sysfs at runtime if required):
PRU-ICSS0 PRU0 Core: am437x-pru0_0-fw
PRU-ICSS0 PRU1 Core: am437x-pru0_1-fw
Note:
1. There are few more sub-modules like the Industrial Ethernet Peripheral
(IEP), eCAP, UART, that do not have bindings and so will be added in the
future. Only UART is pinned out, so others should be added in disabled
state if added.
2. The PRUSS0 INTC on AM437x SoCs routes the host interrupt 5 to the other
PRUSS1, so it is already marked reserved through the 'ti,irqs-reserved'
property.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the DT node for the PRU-ICSS1 instance on the AM437x family of SoCs.
Each PRU-ICSS instance is represented by a pruss node and other child
nodes. The nodes are added under the interconnect target module node in
the common am4372 dtsi file. The PRU-ICSS instances are supported only
on AM4376+ SoCs though in the AM437x family, so the interconnect target
module node should be disabled in any derivative board dts file that
uses AM4372 SoCs.
The PRU-ICSS1 on AM437x is very similar to the PRUSS in AM33xx, except
for variations in the RAM sizes, bus addresses and the number of
interrupts coming into the MPU INTC (host interrupt 5 is routed to
the other PRUSS instead of MPU).
The PRUSS subsystem node contains the entire address space. The various
sub-modules of the PRU-ICSS are represented as individual child nodes
(so platform devices themselves) of the PRUSS subsystem node. These
include the two PRU cores and the interrupt controller. All the Data
RAMs are represented within a child node of its own named 'memories'
without any compatible. The Real Time Media Independent Interface
controller (MII_RT), and the CFG sub-module are represented as syscon
nodes. The PRUSS CFG module has a clock mux for IEP clock, this clk
node is added under the CFG child node 'clocks'. The default source
for this mux clock is the PRU_ICSS_IEP_GCLK clock.
The DT nodes use all standard properties. The regs property in the PRU
nodes define the addresses for the Instruction RAM, the Debug and Control
sub-modules for that PRU core. The firmware for each PRU core is defined
through a 'firmware-name' property.
The default names for the firmware images for each PRU core are defined
as follows (these can be adjusted either in derivative board dts files
or through sysfs at runtime if required):
PRU-ICSS1 PRU0 Core: am437x-pru1_0-fw
PRU-ICSS1 PRU1 Core: am437x-pru1_1-fw
Note:
1. There are few more sub-modules like the Industrial Ethernet Peripheral
(IEP), MDIO, UART, eCAP that do not have bindings and so will be added
in the future.
2. The PRUSS INTC on AM437x SoCs also connect the host interrupt 0 to ADC0
and ADC1; 6 and 7 as possible DMA events, so use the 'ti,irqs-reserved'
property in derivative board dts files _if_ any of them should not be
handled by the host OS. Host interrupt 5 is already marked reserved as
it is connected to the other PRUSS instance.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation for probing l3 with simple-pm-bus and genpd, we must move
l3 noc to a separate node to prevent omap_l3_noc.c driver from claiming
the whole l3 instance before simple-pm-bus has a chance to probe.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Note that we need to use "ti,no-idle" here.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver.
Note that we no longer need ti,no-reset-on-init as the rstctrl resets
are properly handled by the reset driver and claimed by the RTC driver.
And we need to squash together the module ranges for driver compability.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We now manage clocksource and clockevent clocks directly with
timer-ti-dm-systimer. In order to use genpd with prm_omap,
GENPD_FLAG_PM_CLK and simple-pm-bus, we need to keep the system
timer related interconnect clocks enabled until clocksource suspend
is done.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add remaining PRM instances for the am43xx SoC. Additionally enable the
genpd support for them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dual_mac mode has been preserved the same way between legacy and new
driver, and one port devices works the same as 1 dual_mac port - it's safe
to switch drivers.
So, Switch all am437x boards to use new cpsw switch driver. Those boards
have or 2 Ext. port wired and configured in dual_mac mode by default, or
only 1 Ext. port.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can power off the SGX power domain when not in use when we configure
it for genpd. And with that change, we can now also drop the old unused
legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and following
the already supported Cortex-A1`5 and Cortex-A57 based Alpine chips.
This one is added together with the official Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile phone
chips from 2017 based on Cortex-A53 or Kryo 260 CPUs.
A total of five end-user products are added based on these, all
Android phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and
XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals.
It is added along with the HopeRun HiHope RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook
based on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels
and become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board
for the Tegra194, their latest 64-bit chip based on Carmel CPU
cores and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added:
The MYiR MYS-6ULX single-board computer, and four different
models of industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony
Xperia Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards.
Beacon EmbeddedWorks adds another SoM+Carrier development board
for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it
is based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Tpj3
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix dtschema validator warnings like:
l2-cache-controller@48242000: $nodename:0: 'l2-cache-controller@48242000'
does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I forgot to send a pull request earlier for converting am3 and am4 to
use sdhci-omap driver instead of the old omap_hsmmc driver.
There was a display subsystem related suspend and resume regression found
recently and looks like I forgot to send a pull request for this patch
while debugging the regression. This patch has been tested without the
display subsystem, and has been in Linux next for several weeks now, so
would be good to have merged for v5.8.
-----BEGIN PGP SIGNATURE-----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=UNki
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/dt-missed-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/omap-fixes
Missed sdhci patch for am3 and am4
I forgot to send a pull request earlier for converting am3 and am4 to
use sdhci-omap driver instead of the old omap_hsmmc driver.
There was a display subsystem related suspend and resume regression found
recently and looks like I forgot to send a pull request for this patch
while debugging the regression. This patch has been tested without the
display subsystem, and has been in Linux next for several weeks now, so
would be good to have merged for v5.8.
* tag 'omap-for-v5.8/dt-missed-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Move am33xx and am43xx mmc nodes to sdhci-omap driver
Link: https://lore.kernel.org/r/pull-1591637467-607254@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Cc: devicetree@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move mmc nodes to be compatible with the sdhci-omap driver. The following
modifications are required for omap_hsmmc specific properties:
ti,non-removable: convert to the generic mmc non-removable
ti,needs-special-reset: co-opted into the sdhci-omap driver
ti,dual-volt: removed. Legacy property not used in am335x or am43xx
ti,needs-special-hs-handling: removed. Legacy property not used in am335x
or am43xx
Also since the sdhci-omap driver does not support runtime PM, explicitly
disable the mmc3 instance in the dtsi.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM437x family of SoCs contains two dissimilar PRU-ICSS instances,
but leverage a common reset line and SYSCFG from the larger PRU-ICSS1
instance. This SYSC register has also very unique bit-fields. Both
the IPs require the PRCM reset to be deasserted to be able to access
any registers. Add a common PRUSS interconnect target-module with all
the required properties.
The PRUSS devices themselves shall be added as child nodes to this
interconnect node in the future. The PRU-ICSS instances are not
supported on AM4372 SoC though in the AM437x family, so the target
module node should be disabled in any derivative board files that
use this SoC.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am437x, the display subsystem (DSS) is on l4. We already have
the interconnect target module for it, so let's just move dss
there.
To do that, we need to adjust the module addresses for the ranges,
and use the ranges already added earlier based on reading the l4
interconnect instance AP registers.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add idle_states table for CPU on am437x. Currently just add C1 state
which gates the MPU clock domain.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series of changes mostly configures the cameras for dra7 and
am437x that have been pending for few months now because of waiting
for clock dependencies to clear. So these changes are based on earlier
dts changes with with Tero Kristo's for-5.6-ti-clk branch merged in.
Then there's a series of changes to configure powervr sgx target module
for am335x, am437x and dra7 that have been waiting to have the rstctrl
reset driver dependencies to clear.
Also included are few minor patches to configure 1-wire and coulomb
counter calibration interrupt for droid4.
-----BEGIN PGP SIGNATURE-----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=u4PK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Late omap dts changes for v5.6 merge window
This series of changes mostly configures the cameras for dra7 and
am437x that have been pending for few months now because of waiting
for clock dependencies to clear. So these changes are based on earlier
dts changes with with Tero Kristo's for-5.6-ti-clk branch merged in.
Then there's a series of changes to configure powervr sgx target module
for am335x, am437x and dra7 that have been waiting to have the rstctrl
reset driver dependencies to clear.
Also included are few minor patches to configure 1-wire and coulomb
counter calibration interrupt for droid4.
* tag 'omap-for-v5.6/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: dts: Add omap3-echo
ARM: dts: Add dtsi files for AM3703, AM3715 and DM3725
ARM: dts: am335x-icev2: Add support for OSD9616P0899-10 at i2c0
...
Link: https://lore.kernel.org/r/pull-1579896427-50330@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
This seems to be similar to what we have for am335x. The following can be
tested via sysfs with the to ensure the SGX module gets enabled and disabled
properly:
# echo on > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5600fe00 # revision register
0x5600fe00 = 0x40000000
# echo auto > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5000fe00
Bus error
Note that this patch depends on the PRM rstctrl driver that has
been recently posted. If the child device driver(s) need to prevent
rstctrl reset on PM runtime suspend, the drivers need to increase
the usecount for the shared rstctrl reset that can be mapped also
for the child device(s) or accessed via dev->parent.
Cc: Adam Ford <aford173@gmail.com>
Cc: Filip Matijević <filip.matijevic.pz@gmail.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: moaz korena <moaz@korena.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Philipp Rossak <embed3d@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Acked-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Similar to am3, I could not find any documentation for the sysc
register on this one, but it seems to work just fine based on
"ti,sysc-omap3-sham" compatible style configuration.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Acked-by: Jean Pihet <jean.pihet@newoldbits.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series of changes adds the PRM reset driver nodes for am3/4, omap4/5
and dra7 SoCs. The reset driver changes make it easier to add support for
various accelerators for TI SoCs in a more generic way.
Note that this branch is based on the PRM reset driver changes branch.
-----BEGIN PGP SIGNATURE-----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=4DAS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/prm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
PRM reset control dts changes for v5.5 merge window
This series of changes adds the PRM reset driver nodes for am3/4, omap4/5
and dra7 SoCs. The reset driver changes make it easier to add support for
various accelerators for TI SoCs in a more generic way.
Note that this branch is based on the PRM reset driver changes branch.
* tag 'omap-for-v5.5/prm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Add PRM data
ARM: dts: am43xx: Add PRM data
ARM: dts: am33xx: Add PRM data
ARM: dts: omap4: add PRM nodes
ARM: dts: dra7: add PRM nodes
soc: ti: omap-prm: add omap5 PRM data
soc: ti: omap-prm: add am4 PRM data
soc: ti: omap-prm: add dra7 PRM data
soc: ti: omap-prm: add data for am33xx
soc: ti: omap-prm: add omap4 PRM data
soc: ti: omap-prm: add support for denying idle for reset clockdomain
soc: ti: omap-prm: poll for reset complete during de-assert
soc: ti: add initial PRM driver with reset control support
dt-bindings: omap: add new binding for PRM instances
Link: https://lore.kernel.org/r/pull-1572623173-281197@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes continues dropping legacy platform data for
omaps. With the proper device tree configuration in place in the dts
files for ti-sysc interconnect target module driver, we can drop the
related platform data and legacy ti,hwmods custom property.
Most of the patches in this series drop platform data and custom dts
property one device class and one SoC at time. This way we can easily
revert one patch at a time in case of unexpected issues if the fix is
not trivial.
For am335x musb, we need to first update the device tree to probe with
ti-sysc interconnect target module driver. And then the following
patches drop the legacy platform data.
Note that this series depends on earlier ti-sysc related driver changes
-----BEGIN PGP SIGNATURE-----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=FUNk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Drop legacy platform data for omaps for v5.5
This series of changes continues dropping legacy platform data for
omaps. With the proper device tree configuration in place in the dts
files for ti-sysc interconnect target module driver, we can drop the
related platform data and legacy ti,hwmods custom property.
Most of the patches in this series drop platform data and custom dts
property one device class and one SoC at time. This way we can easily
revert one patch at a time in case of unexpected issues if the fix is
not trivial.
For am335x musb, we need to first update the device tree to probe with
ti-sysc interconnect target module driver. And then the following
patches drop the legacy platform data.
Note that this series depends on earlier ti-sysc related driver changes
* tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (40 commits)
ARM: OMAP2+: Drop legacy platform data for am335x musb
ARM: dts: Drop pointless status changing for am3 musb
ARM: dts: Probe am335x musb with ti-sysc
ARM: OMAP2+: Drop legacy platform data for musb on omap4
ARM: OMAP2+: Drop legacy platform data for omap4 mcasp
ARM: OMAP2+: Drop legacy platform data for am3 and am4 mcasp
ARM: OMAP2+: Drop legacy platform data for dra7 rng
ARM: OMAP2+: Drop legacy platform data for am3 and am4 rng
ARM: OMAP2+: Drop legacy platform data for omap4 hdq1w
ARM: OMAP2+: Drop legacy platform data for dra7 hdq1w
ARM: OMAP2+: Drop legacy platform data for am4 hdq1w
ARM: OMAP2+: Drop legacy platform data for omap5 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap4 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap5 wdt
ARM: OMAP2+: Drop legacy platform data for dra7 wdt
ARM: OMAP2+: Drop legacy platform data for am3 and am4 wdt
ARM: dts: Drop custom hwmod property for omap5 mmc
ARM: dts: Drop custom hwmod property for am4 mmc
ARM: dts: Drop custom hwmod property for am3 mmc
ARM: dts: Drop custom hwmod property for omap5 i2c
...
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes adds support for few new boards, moves
remaining ti wilink bluetooth users to use the serdev driver,
and improves support for existing devices:
- Add support for NetCAN Plus devices
- Configure wilink bluetooth for logicpd-torpedo and omap3-igep
- Switch to using generic LCD panel for logicpd-torpedo and
increase camera pixel clock
- Configure droid4 for 300mA USB host mode and move to a common file
to start adding support for droid bionic
- Rename ocmcram node to sram
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl2xz34RHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXP7UBAA07dGQrlE9JroNSOsdEK5I3vpd27QQ08+
ESvErr5INTt0ePAPsqN7agxc66eDhyElm0BYouS9MOWOax/obCNo2WSVqXrf0Msi
+Ge7mzHNoI1M6j+z8zbMwLuAaLSfvkdEspxAXkK8SQUjZcvg7gIsH/s2MNB5bvYO
kr+SGel2n1Mx+tP+UQvu94q4MT1zMlDApPpBFzBVZg5uNKYBanlMqnS0c/FPVzR6
BU56WfV6toX7AjcIIHn0Okmlnh3c0DDursrpFswWhH7+AM9XUgy9ygdsVYSbTRfg
BSCE3vV9aL8c8eyZ7GGuNMw5kGLc1q2VUh0rJnVYFzJy4nl8AufDw4ABVPgJGQ3l
UCrUQm8ZPaHwngQCgRax9iJuymEwVCLIPB96+Wfb/VTC5BlwMcUl68atcRgyMeGG
V6zPOPfRivV98r9znOhAjN+eW2vzSCwixWoqZna5yp7wvBUPqP3u6C9hQZxOzn+i
cu9dMpeYLSf0GDQo/SXHGW/gMf0bzWg2giFMC/WgEeUtdrasbRjYvUzIV5dZZAvY
a+LkhsoSeT4VFm+OGKRNozfhEb6kMqkV6tOHPtBljxWpRswWdCKrq2eenI+kyU4K
tNO5jIqaVIqBDTXT4J6J9m5W2j/lViYr1doFu0hJ3mbKy9j1M1LCCacCAcwYoAU8
LSH/xj0EVyc=
=Gllx
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Device tree changes for omaps for v5.5
This series of changes adds support for few new boards, moves
remaining ti wilink bluetooth users to use the serdev driver,
and improves support for existing devices:
- Add support for NetCAN Plus devices
- Configure wilink bluetooth for logicpd-torpedo and omap3-igep
- Switch to using generic LCD panel for logicpd-torpedo and
increase camera pixel clock
- Configure droid4 for 300mA USB host mode and move to a common file
to start adding support for droid bionic
- Rename ocmcram node to sram
* tag 'omap-for-v5.5/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: add DTS for NetCom Plus 4xx and 8xx device series
ARM: dts: add DTS for NetCom Plus 1xx and 2xx device series
ARM: dts: add DTS for NetCAN Plus devices
ARM: dts: omap: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo-37xx-devkit: Increase camera pixel clock
ARM: dts: am: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo: Disable Bluetooth Serial DMA
ARM: dts: IGEP: Add WiLink UART node
ARM: dts: LogicPD Torpedo: Add WiLink UART node
ARM: dts: logicpd-torpedo-37xx-devkit-28: Reference new DRM panel
ARM: dts: logicpd-torpedo-baseboard: Reduce video regulator chatter
ARM: dts: Add minimal support for Droid Bionic xt875
ARM: dts: omap4-droid4: Allow 300mA current for USB peripherals
ARM: dts: Use level interrupt for omap4 & 5 wlcore
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
The device node name should reflect generic class of a device so rename
the "ocmcram" node and its children to "sram". This will be also in
sync with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add PRM data for AM43xx SoC. Initially this is used to provide reset
support, but will be expanded later to support also powerdomain control.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to
avoid underflow errors due to the bandwidth needs of higher resolutions.
am43xx can not provide enough bandwidth to DISPC to correctly handle
'high' resolutions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 4e27f752ab ("ARM: OMAP2+: Drop mmc platform data for am330x and
am43xx") dropped legacy mmc platform data for am3 and am4, but missed the
fact that we never updated the dts files for mmc3 that is directly on l3
interconnect instead of l4 interconnect. This leads to a situation with
no legacy platform data and incomplete dts data.
Let's update the mmc instances on l3 interconnect to probe properly with
ti-sysc interconnect target module driver to make mmc3 work again. Let's
still keep legacy "ti,hwmods" property around for v5.2 kernel and only
drop it later on.
Note that there is no need to use property status = "disabled" for mmc3.
The default for dts is enabled, and runtime PM will idle unused instances
just fine.
Fixes: 4e27f752ab ("ARM: OMAP2+: Drop mmc platform data for am330x and am43xx")
Reported-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Note that we are not yet moving dss or wkup_m3, those will be moved
later after some related driver changes.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Thomas Gleixner