Presently the sysdevs are simply numbered based on the list position,
without having any direct way of figuring out which controller these are
actually mapping to. This provides a name attr for mapping out the chip
name.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: remove duplicated #include
sh: Export uncached helper symbols.
sh: Fix up NUMA build for 29-bit.
serial: sh-sci: Fix build failure for non-sh architectures.
sh: Fix up uncached offset for legacy 29-bit mode.
sh: Support CPU affinity masks for INTC controllers.
Extend the INTC code with ioremap() support V2.
Support INTC controllers that are not accessible through
a 1:1 virt:phys window. Needed by SH-Mobile ARM INTCS.
The INTC code behaves as usual if the io window resource
is omitted. The slow phys->virt lookup only happens during
setup. The fast path code operates on virtual addresses.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the INTC code to warn and return an error code
in the case of memory allocation failure.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This hooks up the ->set_affinity() for the INTC controllers, which can be
done as just a simple copy of the cpumask. The enable/disable paths
already handle SMP register strides, so we just test the affinity mask in
these paths to determine which strides to skip over.
The early enable/disable path happens prior to the IRQs being registered,
so we have no affinity mask established at that point, in which case we
just default to CPU_MASK_ALL. This is left as it is to permit the force
enable/disable code to retain existing semantics.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently there's an ordering issue with the chained handler change
which places the set_irq_chip() after set_irq_chained_handler(). This
causes a warning to be emitted as the IRQ chip needs to be set first.
However, there is the caveat that redirect IRQs can't use the parent
IRQ's irq chip as they are just dummy redirects, resulting in
intc_enable() blowing up when set_irq_chained_handler() attempts to
start up the redirect IRQ. In these cases we can just use dummy_irq_chip
directly, as we already extract the parent IRQ and chip from the redirect
handler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the shared INTC code with force_disable support to
allow keeping mask bits statically disabled. Needed for
SDHI support to mask out unsupported interrupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the shared INTC code to use
set_irq_chained_handler() for intc_redirect_irq().
With this in place request_irq() on a merged irq
which has been redirected will now return -EINVAL
instead of 0 together with a crash. This thanks to
the protection of the IRQ_NOREQUEST flag set for
chained interrupt handlers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the shared INTC code with force_enable support to
allow keeping mask bits statically enabled. Needed by
upcoming INTC SDHI patches that mux together a bunch of
vectors to a single linux interrupt which is masked by
a priority register, but needs individual mask bits
constantly enabled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the INTC code by moving all vectors,
groups and registers from struct intc_desc to struct
intc_hw_desc.
The idea is that INTC tables should go from using the
macro(s) DECLARE_INTC_DESC..() only to using struct
intc_desc with name and hw initialized using the macro
INTC_HW_DESC(). This move makes it easy to initialize
an extended struct intc_desc in the future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Reuse the SuperH INTC code on ARM by using set_irq_flags()
to set IRQF_VALID on ARM platforms.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This just reworks the existing create_irq_on_node() in to the new
create_irq_nr() which is generally exposed. This permits boards that
haven't converted over to sparseirq to try and use their existing ranges,
rather than having arbitrary vectors assigned to them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the resume from hibernation
in the intc sysdev device when it manages 'redirect' irq
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Different CPUs will have different starting vectors, with varying
amounts of reserved or unusable vector space prior to the first slot.
This introduces a legacy vector reservation system that inserts itself in
between the CPU vector map registration and the platform specific IRQ
setup. This works fine in practice as the only new vectors that boards
need to establish on their own should be dynamically allocated rather
than arbitrarily assigned. As a plus, this also makes all of the
converted platforms sparseirq ready.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for dynamic IRQ allocation/deallocation for all parts
using the SH-style vectored IRQs. While this is not inherently
INTC-specific, the INTC code is the main tie-in for vectored IRQ
registration, and is the only place that a full view of the utilized
vector map is possible.
The implementation is fairly straightforward, implementing a flat IRQ map
where each registered vector is reserved, allowing us to scan for holes
and dynamically wire up IRQs lazily later on in the boot stage. This
piggybacks on top of sparseirq in order to make the best use of the
available vector space.
Dynamic IRQs can be used for any number of things, ranging from MSI in
the SH-X3 PCIe case down to demux vectors for board FPGAs and system
controllers that presently allocate an arbitrary range. In the latter
case, this also allows those platforms to use sparseirq without blowing
up, which brings us one step closer to enabling sparseirq as the default
for all platform and CPU combinations.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently this is ifdef'ed under SH-3 and SH-4A, but there are other CPUs
that will need this as well. Given the size of the existing data
structures, this doesn't cause any additional cacheline utilization for
the existing users, so has no direct impact on the data structures.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the simplified multi-evt handling when sparseirq support is
enabled. While vectors are redirected through the single unique masking
source, each one of the redirected vectors still requires its own backing
irq_desc, which needs to be manually allocated in the sparseirq case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the way in which "multi-evt" interrups are handled.
The intc_evt2irq_table and related intc_evt2irq() have been removed and
the "redirecting" handler is installed for the coupled interrupts.
Thanks to that the do_IRQ() function don't have to use another level
of indirection for all the interrupts...
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It is possible for the CPU to re-enable it's interrupt block bit
before the write to the interrupt controller has actually masked out
the external interupt at the controller. We get around this by
reading back from the interrupt controller which will ensure the
write has happened.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the slab allocators are available much earlier, this triggers a
the slab_is_available() warning when registering the interrupt
controller. Convert to kzalloc() with GFP_NOWAIT, as per the generic
changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the dependent patches are merged, we are ready to enable
sparseirq support. This simply adds the Kconfig option, and then converts
from the _cpu to the _node allocation routines to follow the upstream
sparseirq API changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
irq_to_desc_alloc_cpu() has been renamed to irq_to_desc_alloc_node() in
-next, but as we can not presently enable SPARSE_IRQ without the early
irq_desc alloc patch, protect it with an ifdef until the interface has
settled and we are ready to enable it system-wide.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This hooks in irq_to_desc_alloc_cpu() to the necessary code paths in the
intc and ipr controller registration paths. As these are the primary call
paths for all SH CPUs, this alone will make all CPUs sparse IRQ ready.
There is the added benefit now that each CPU contains specific IPR and
INTC tables, so only the vectors with interrupt sources backing them will
ever see an irq_desc instantiation. This effectively packs irq_desc
down to match the CPU, rather than padding NR_IRQS out to cover the valid
vector range.
Boards with extra sources will still have to fiddle with the nr_irqs
setting, but they can continue doing so through the machvec as before.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It's required for all modules loaded in the previous runtime
session because not initilized duing the kernel start-up.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add set_irq_wake() support to intc using sysdev and suspend.
The intc controllers are put on a list at registration time
and registered as sysdev devices later on during the boot.
The sysdev class suspend callback is used to find irqs with
wakeup enabled belonging to our intc controller. Such irqs
are simply enabled so wakeup interrupts may reach the cpu.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Modify the intc code to install a disable callback. The current
solution without a disable callback results in use of the
generic default_disable() function. This function is a no-op
so suspend_device_irqs() will not disable any intc interrupts
at suspend time without this patch. Also, install enable and
shutdown callbacks while at it.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:
- If multiple vectors share the same enum then only the
first vector will be available as a linux irq.
- Drivers may need to be rewritten to get pending irq
source from the hardware block instead of irq number.
This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.
Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The INTC code will be re-used across different architectures, so move
this out to drivers/sh/ and include/linux/sh_intc.h respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt