This patch adds support to WSA8830/WSA8812/WSA8835 Class-D Smart
Speaker Amplifier. This Amplifier is primarily interfaced with
SoundWire.
This patch is tested on SM8450 MTP Board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220629090644.67982-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add generic ASoC equivalent of ALSA HD-Audio codec. This codec is
designed to follow HDA_DEV_LEGACY convention. Driver wrapps existing
hda_codec.c handlers to prevent code duplication within the newly added
code. Number of DAIs created is dependent on capabilities exposed by the
codec itself. Because of this, single solution can be applied to support
every single HD-Audio codec type.
At the same time, through the ASoC topology, platform drivers may limit
the number of endpoints available to the userspace as codec driver
exposes BE DAIs only.
Both hda_codec_probe() and hda_codec_remove() declare their expectations
on device's usage_count and suspended-status. This is to catch any
unexpected behavior as PM-related code for HD-Audio has been changing
quite a bit throughout the years.
In order for codec DAI list to reflect its actual PCM capabilities, PCMs
need to be built and that can only happen once codec device is
constructed. To do that, a valid component->card->snd_card pointer is
needed. Said pointer will be provided by the framework once all card
components are accounted for and their probing can begin. Usage of
"binder" BE DAI solves the problem - codec can be listed as one of
HD-Audio card components without declaring any actual BE DAIs
statically.
Relation with hdac_hda:
Addition of parallel solution is motivated by behavioral differences
between hdac_hda.c and its legacy equivalent found in sound/pci/hda
e.g.: lack of dynamic, based on codec capabilities, resource allocation
and high cost of removing such differences on actively used targets.
Major goal of codec driver presented here is to follow HD-Audio legacy
behavior in 1:1 fashion by becoming a wrapper. Doing so increases code
coverage of the legacy code and reduces the maintenance cost for both
solutions.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220511162403.3987658-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series of patches adds support for Analog Devices MAX98396
mono amplifier with IV sense. The device provides a PCM interface
for audio data and a standard I2C interface for control data
communication. This driver also supports MAX98397 which is
a variant of MAX98396 with wide input supply range.
Signed-off-by: Ryan Lee <ryan.lee.analog@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220423021558.1773598-1-ryan.lee.analog@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt1016 driver wasn't listed in Kconfig and Makefile, which AFAICT
means it isn't ever built. This patch adds the appropriate entries to
Kconfig and Makefile.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20220405171158.2168762-1-steve@sk2.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS35L45 is a 15 V Boosted Mono Class D Amplifier with DSP
Speaker Protection and Adaptive Battery Management.
This initial driver provides standard non-boosted audio operation
without the DSP.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220405135419.1230088-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Placing both the I2C and SPI code in the same module causes problems with
mixes of modular and non-modular builds of the buses so it's generally bad
practice. As with other drivers split the bus code out of the WM8731 driver
into separate modules.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220325153121.1598494-6-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Awinic AW8738 is a simple audio amplifier using a single GPIO.
The main difference to simple-amplifier is that there is a "one-wire
pulse control" that allows configuring the amplifier to one of a few
pre-defined modes. This can be used to configure the speaker-guard
function (primarily the power limit for the amplifier).
Add a simple driver that allows setting it up in the device tree
with a specified mode number.
Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20220304102452.26856-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for enabling required power domains in digital macro codecs.
macro and dcodec power domains are being requested as clocks by HLOS
in ADSP based architectures and ADSP internally handling as powerdomains.
In ADSP bypass case need to handle them as power domains explicitly.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/1645898959-11231-2-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS5805M is a class D audio amplifier with an
integrated DSP. DSP configuration is supplied in a firmware image
specified through a device-tree attribute.
These register writes set up application-specific DSP settings and are
expected to be generated using TI's PPC3 tool.
Signed-off-by: Daniel Beer <daniel.beer@igorinstitute.com>
Link: https://lore.kernel.org/r/b82fac1d21a33a5f57a5819eaf37c31f5c86eb65.1642298336.git.daniel.beer@igorinstitute.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To support CS35L41 in HDA systems the HDA driver
for CS35L41 would have to duplicate some functions
that already exist on ASoC driver
So instead of duplicate the code, use the new lib
source as a shared resource for both ASoC and HDA
Also, change the way CONFIG_SND_SOC_CS35L41 is
selected, as reported by Intel Kernel test robot,
it is possible to build SND_SOC_CS35L41_SPI/I2C
without the main driver, which would lead to build
failures.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211217115708.882525-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Can't link I2C and SPI to the same binary, better
to move CS35L41 to 3 modules approach.
And instead of exposing cs35l41_reg, volatile_reg,
readable_reg and precious_reg arrays, move
cs35l41_regmap_i2c/spi to new module and expose it.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211125143501.7720-1-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This drops the rt9210 support due to a race with a new version being
sent out for some incremental changes.
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is for codec NAU88L21 of Nuvoton Technology Corporation.
The NAU88L21 is an ultra-low power high performance audio codec that
supports both analog and digital audio functions.
Signed-off-by: Seven Lee <wtli@nuvoton.com>
Link: https://lore.kernel.org/r/20211001103108.3297848-1-wtli@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is an initial codec driver for Realtek ALC5682I-VS codec.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Signed-off-by: Derek Fang <derek.fang@realtek.com<mailto:derek.fang@realtek.com>>
Link: https://lore.kernel.org/r/20210831130258.19286-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Core has updates to support SoundWire mockup device (includes tag from
asoc), improved error handling and slave status.
- Drivers has update on Intel driver for new quriks and better handling of
errors and suspend routines
-----BEGIN PGP SIGNATURE-----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=TCAF
-----END PGP SIGNATURE-----
Merge tag 'soundwire-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire updates for 5.15-rc1
- Core has updates to support SoundWire mockup device (includes tag from
asoc), improved error handling and slave status.
- Drivers has update on Intel driver for new quriks and better handling of
errors and suspend routines
* tag 'soundwire-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: cadence: do not extend reset delay
soundwire: intel: conditionally exit clock stop mode on system suspend
soundwire: intel: skip suspend/resume/wake when link was not started
soundwire: intel: fix potential race condition during power down
soundwire: cadence: override PDI configurations to create loopback
soundwire: cadence: add debugfs interface for PDI loopbacks
soundwire: stream: don't program mockup device ports
soundwire: bus: squelch error returned by mockup devices
soundwire: add flag to ignore all command/control for mockup devices
soundwire: stream: don't abort bank switch on Command_Ignored/-ENODATA
soundwire: cadence: add paranoid check on self-clearing bits
soundwire: dmi-quirks: add quirk for Intel 'Bishop County' NUC M15
soundwire: bus: update Slave status in sdw_clear_slave_status
soundwire: cadence: Remove ret variable from sdw_cdns_irq()
soundwire: bus: filter out more -EDATA errors on clock stop
soundwire: dmi-quirks: add ull suffix for SoundWire _ADR values
ASoC: Intel: boards: sof_sdw: add SoundWire mockup codecs for tests
ASoC: soc-acpi: tgl: add table for SoundWire mockup devices
ASoC: soc-acpi: cnl: add table for SoundWire mockup devices
ASoC: codecs: add SoundWire mockup device support
With SND_SOC_ALL_CODECS=y and SND_SOC_WCD938X_SDW=m, there is a link
error from a reverse dependency, since the built-in codec driver calls
into the modular soundwire back-end:
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_codec_free':
wcd938x.c:(.text+0x2c0): undefined reference to `wcd938x_sdw_free'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_codec_hw_params':
wcd938x.c:(.text+0x2f6): undefined reference to `wcd938x_sdw_hw_params'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_codec_set_sdw_stream':
wcd938x.c:(.text+0x332): undefined reference to `wcd938x_sdw_set_sdw_stream'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_tx_swr_ctrl':
wcd938x.c:(.text+0x23de): undefined reference to `wcd938x_swr_get_current_bank'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_bind':
wcd938x.c:(.text+0x2579): undefined reference to `wcd938x_sdw_device_get'
x86_64-linux-ld: wcd938x.c:(.text+0x25a1): undefined reference to `wcd938x_sdw_device_get'
x86_64-linux-ld: wcd938x.c:(.text+0x262a): undefined reference to `__devm_regmap_init_sdw'
Work around this using two small hacks: An added Kconfig dependency
prevents the main driver from being built-in when soundwire support
itself is a loadable module to allow calling devm_regmap_init_sdw(),
and a Makefile trick links the wcd938x-sdw backend as built-in
if needed to solve the dependency between the two modules.
Fixes: 0454422288 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721150510.1837221-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
To test the host controller and bus management code, it is currently
required to have a physical SoundWire peripheral attached to the
bus. To help with pre-silicon or early hardware enablement, it would
be very useful to have a SoundWire 'mockup' device that is exposed in
platform firmware but does not drive any signal on the bus.
This is different to the existing ASoC 'dummy' codec uses for I2S/TDM,
the SoundWire spec makes it clear that a device that is not attached
to the bus is not permitted to interact with the bus, be it for
command/control or data.
This patch exposes a 'mockup' device, with a minimalist driver, with 4
partID values reserved by Intel for such test configurations. The
mockup device exposes one full-duplex DAI based on 2 ports (DP1 for
playback and DP8 for capture). The capture data port is just virtual,
such a mockup device is prevented by the SoundWire specification from
presenting any data generated by a Source port without being Attached.
All the callbacks exposed by the SoundWire Slave interface are
populated, even if they just return immediately. This is intentional
to describe what a minimal codec driver should do and implement and
help new codec vendors provide support for their devices.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Most new Qualcomm WCD codecs support MBHC(Multi Button Headset Control) via ADC.
This patchset adds support to Common parts of this MBHC support so that
WCD codecs need not duplicate them. To do that codec exposes set of
register fields and callbacks to this common driver to control it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210604115230.23259-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the Rockchip rk817 audio codec integrated into the
rk817 PMIC. This is based on the sources provided by Rockchip from
their BSP kernel.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Tested-by: Maciej Matuszczyk <maccraft123mc@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
NXP's TFA98xx (now part of Goodix) are fairly popular speaker amplifiers
used in many smartphones and tablets. Most of them are sold as "smart
amplifiers" with built-in "CoolFlux DSP" that is used for volume control,
plus a "sophisticated speaker-boost and protection algorithm".
Unfortunately, they are also almost entirely undocumented. The short
datasheets (e.g. [1] for TFA9897) describe the available features,
but do not provide any information about the registers or how to use
the "CoolFlux DSP".
The amplifiers are most often configured through proprietary userspace
libraries. There are also some (rather complex) kernel drivers (e.g. [2])
but even those rely on obscure firmware blobs for configuration (so-called
"containers"). They seem to contain different "profiles" with tuned speaker
settings, sample rates and volume steps (which would be better exposed
as separate ALSA mixers).
The format of the firmware files seems to have changed a lot over the time,
so it's not even possible to simply re-use the firmware originally provided
by the vendor.
Overall, it seems close to impossible to develop a proper mainline driver
for these amplifiers that could make proper use of the built-in DSP.
This commit implements a compromise: At least the TFA1 family of the
TFA98xx amplifiers (usually called TFA989x) provide a way to *bypass*
the DSP using a special register sequence. The register sequence can be
found in similar variations in the kernel drivers from lots of vendors
e.g. in [3] and was probably mainly used for factory testing.
With the DSP bypassed, the amplifier acts mostly like a dumb standard
speaker amplifier, without (hardware) volume control. However, the setup
is much simpler and it works without any obscure firmware.
This driver implements the DSP bypass combined with chip-specific
initialization sequences adapted from [2]. Only TFA9895 is supported in
this initial commit. Except for the lack of volume control I can not hear
any difference with or without the DSP, it works just fine.
This driver allows the speaker to work on mainline Linux running on the
Samsung Galaxy A3/A5 (2015) [TFA9895] and Alcatel Idol 3 [TFA9897].
TFA9897 support will be added in separate patch set later.
[1]: https://product.goodix.com/en/docview/TFA9897%20SDS_Rev.3.1?objectId=47&objectType=document&version=78
[2]: https://source.codeaurora.org/external/mas/tfa98xx
[3]: 57b5050e34/sound/soc/codecs/tfa98xx.c (L1422-L1462)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210513104129.36583-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the arizona extcon driver into a helper library for direct use
from the arizona codec-drivers, rather then being bound to a separate
MFD cell.
Note the probe (and remove) sequence is split into 2 parts:
1. The arizona_jack_codec_dev_probe() function inits a bunch of
jack-detect specific variables in struct arizona_priv and tries to get
a number of resources where getting them may fail with -EPROBE_DEFER.
2. Then once the machine driver has create a snd_sock_jack through
snd_soc_card_jack_new() it calls snd_soc_component_set_jack() on
the codec component, which will call the new arizona_jack_set_jack(),
which sets up jack-detection and requests the IRQs.
This split is necessary, because the IRQ handlers need access to the
arizona->dapm pointer and the snd_sock_jack which are not available
when the codec-driver's probe function runs.
Note this requires that machine-drivers for codecs which are converted
to use the new helper functions from arizona-jack.c are modified to
create a snd_soc_jack through snd_soc_card_jack_new() and register
this jack with the codec through snd_soc_component_set_jack().
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-10-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm LPASS (Low Power Audio SubSystem) has internal codec
TX macro block which is used for connecting with external
Soundwire TX Codecs like WCD938x.
This patch adds support to the codec part of the TX Macro block
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210211122735.5691-7-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
LPASS RX Codec Macro is available in Qualcomm LPASS (Low Power Audio SubSystem).
This is used for connecting with SoundWire devices like WCD938x Codecs to provide
headphone/ear/lineout functionality.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210211122735.5691-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the internal codec found in the JZ4760 SoC from Ingenic.
Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210123140958.12895-3-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120162553.21666-3-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120162553.21666-2-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This is quite a busy release for regmap with two substantial features
being added:
- Support for register maps Soundwire 1.2 multi-byte operations,
allowing atomic support for registers larger than a single byte.
- Support for relaxed I/O without barriers in MMIO regmaps, allowing
them to be used efficiently on systems where default MMIO operations
include barriers.
There was also an addition and revert of use of the new Soundwire
support for RT715 due to build issues with the driver built in, my tests
only covered building it as a module, the patch wasn't just dropped as
it had already been merged elsewhere.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl/XdOYACgkQJNaLcl1U
h9DKWwf7BVgrH1vcgOdZ/8xbVnu2pmNGJzHydfV2XD2fHuEgkuVN1dv756HFCzBj
XpHGa+XRGt1j39KsBqhcBOGuCLiTmjmoxWXq4MnBFVHcXBNRk1z6YFtkeZBkRi0j
ZxZNlrrCCaFp8KmqyqMeIU9DbiQ/ITTH/1VBcffnprYI1J9gK4JQE0iisaMIap90
XwKx4VUwT63yVZQGJPW4t65uMUbPTRqcZQzfj3DGhjmkhNI/EvpPU44K11I+op/6
7J9enekMlbOR5t7606h9gAapW1Qt+YrvTwciT9mzGNsmO8MmyUIRQUYuZAzp5RIT
BH5aIRfTUb6lYuktSKI8STrbOUdi/A==
=194Y
-----END PGP SIGNATURE-----
Merge tag 'regmap-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This is quite a busy release for regmap with two substantial features
being added:
- Support for register maps Soundwire 1.2 multi-byte operations,
allowing atomic support for registers larger than a single byte.
- Support for relaxed I/O without barriers in MMIO regmaps, allowing
them to be used efficiently on systems where default MMIO
operations include barriers.
There was also an addition and revert of use of the new Soundwire
support for RT715 due to build issues with the driver built in, my
tests only covered building it as a module, the patch wasn't just
dropped as it had already been merged elsewhere"
* tag 'regmap-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
ASoC: rt715: Fix build
regmap: sdw: add required header files
regmap: Remove duplicate `type` field from regmap `regcache_sync` trace event
regmap: Fix order of regmap write log
regmap: mmio: add config option to allow relaxed MMIO accesses
Add a driver for simple mux driven by gpios. It currently only supports one
gpio, muxing one of two inputs to a single output.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201205001508.346439-2-alexandre.belloni@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the Analog Devices ADAU1372 audio CODEC.
[Alexandre Belloni: allow 32kHz for TDM4 in slave mode]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201127123030.1610574-2-alexandre.belloni@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
First version of rt715 sdw sdca codec driver.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20201103172226.4278-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm LPASS (Low Power Audio SubSystem) has internal codec
VA macro block which is used for connecting with DMICs.
This patch adds support to the codec part of the VA Macro block
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201105113458.12360-6-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm LPASS (Low Power Audio SubSystem) has internal codec
WSA macro block which is used for connecting with WSA Smart
speakers over soundwire.
This patch adds support to the codec part of the WSA Macro block.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201105113458.12360-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add codec driver for Nuvoton NAU8315.
Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201102023212.594137-1-CTLIN0@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Srinivas Kandagatla