Ensure that all mdio devices populate the struct device fwnode pointer
as well as the of_node pointer to allow drivers that wish to use
fwnode APIs to work.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs need a minimum time after the reset gpio was asserted and/or
deasserted. To ensure we meet these timing requirements add two new
optional devicetree parameters for the phy: reset-delay-us and
reset-post-delay-us.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a get_match_data() callback as part of the firmware node,
implement the OF specific piece for it.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Make small cleanup in function description for
of_irq_parse_raw
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The unittests can run on UML, but OF_IRQ and OF_ADDRESS need to be
enabled. Rework the kconfig dependencies to enable the unittests. The
unittests cannot build on Sparc, so we need to add an explicit
dependency for !SPARC.
There's one failure in overlay tests because the base DT is not
unflattened early.
Cc: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Make it more clear that nodes without "__overlay__" subnodes are
skipped, by reverting the logic and using continue.
This also reduces indentation level.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
If an overlay has no "__symbols__" node, but it has nodes without
"__overlay__" subnodes at the end (e.g. a "__fixups__" node), after
filling in all fragments for nodes with "__overlay__" subnodes,
"fragment = &fragments[cnt]" will point beyond the end of the allocated
array.
Hence writing to "fragment->overlay" will overwrite unallocated memory,
which may lead to a crash later.
Fix this by deferring both the assignment to "fragment" and the
offending write afterwards until we know for sure the node has an
"__overlay__" subnode, and thus a valid entry in "fragments[]".
Fixes: 61b4de4e0b ("of: overlay: minor restructuring")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
The special overlay mutex is taken first, hence it should be released
last in the error path.
of_resolve_phandles() must be called with of_mutex held. Without it, a
node and new phandle could be added via of_attach_node(), making the max
phandle wrong.
free_overlay_changeset() must be called with of_mutex held, if any
non-trivial cleanup is to be done.
Hence move "mutex_lock(&of_mutex)" up, as suggested by Frank, and merge
the two tail statements of the success and error paths, now they became
identical.
Note that while the two mutexes are adjacent, we still need both:
__of_changeset_apply_notify(), which is called by __of_changeset_apply()
unlocks of_mutex, then does notifications then locks of_mutex. So the
mutex get released in the middle of of_overlay_apply()
Fixes: f948d6d8b7 ("of: overlay: avoid race condition between applying multiple overlays")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
If of_resolve_phandles() fails, free_overlay_changeset() is called in
the error path. However, that function returns early if the list hasn't
been initialized yet, before freeing the object.
Explicitly calling kfree() instead would solve that issue. However, that
complicates matter, by having to consider which of two different methods
to use to dispose of the same object.
Hence make free_overlay_changeset() consider initialization state of the
different parts of the object, making it always safe to call (once!) to
dispose of a (partially) initialized overlay_changeset:
- Only destroy the changeset if the list was initialized,
- Make init_overlay_changeset() store the ID in ovcs->id on success,
to avoid calling idr_remove() with an error value or an already
released ID.
Reported-by: Colin King <colin.king@canonical.com>
Fixes: f948d6d8b7 ("of: overlay: avoid race condition between applying multiple overlays")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
If an "if" branch is terminated by a "goto", there's no need to have an
"else" statement and an indented block of code.
Remove the "else" statement to simplify the code flow for the casual
reviewer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
overlay_data_add() never takes the special overlay mutex, so it must not
be released in the error patch.
Presumably the call to of_overlay_mutex_unlock() is a relic from v1 of
the patch.
Fixes: f948d6d8b7 ("of: overlay: avoid race condition between applying multiple overlays")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
It isn't clear if this function of_node_put()s the 'from'
argument, or the node it searches. Clearly indicate which
variable is touched. Fold in some more fixes from Randy too
because we're in the area.
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This branch contains platform-related driver updates for ARM and ARM64,
these are the areas that bring the changes:
New drivers:
- Driver support for Renesas R-Car V3M (R8A77970)
- Power management support for Amlogic GX
- A new driver for the Tegra BPMP thermal sensor
- A new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- The usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa, uniphier
and mediatek families.
- Updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi.
Changes specific to some ARM-based SoC
- The Freescale/NXP DPAA QBMan drivers from PowerPC can now work
on ARM as well.
- Several changes for power management on Broadcom SoCs
- Various improvements on Qualcomm, Broadcom, Amlogic, Atmel, Mediatek
- Minor Cleanups for Samsung, TI OMAP SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qDhq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This branch contains platform-related driver updates for ARM and
ARM64, these are the areas that bring the changes:
New drivers:
- driver support for Renesas R-Car V3M (R8A77970)
- power management support for Amlogic GX
- a new driver for the Tegra BPMP thermal sensor
- a new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- the usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa,
uniphier and mediatek families
- updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi
Changes specific to some ARM-based SoC
- the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on
ARM as well
- several changes for power management on Broadcom SoCs
- various improvements on Qualcomm, Broadcom, Amlogic, Atmel,
Mediatek
- minor Cleanups for Samsung, TI OMAP SoCs"
[ NOTE! This doesn't work without the previous ARM SoC device-tree pull,
because the R8A77970 driver is missing a header file that came from
that pull.
The fact that this got merged afterwards only fixes it at this point,
and bisection of that driver will fail if/when you walk into the
history of that driver. - Linus ]
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits)
soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader
bus: add driver for the Technologic Systems NBUS
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
soc: qcom: remove unused label
soc: amlogic: gx pm domain: add PM and OF dependencies
drivers/firmware: psci_checker: Add missing destroy_timer_on_stack()
dt-bindings: power: add amlogic meson power domain bindings
soc: amlogic: add Meson GX VPU Domains driver
soc: qcom: Remote filesystem memory driver
dt-binding: soc: qcom: Add binding for rmtfs memory
of: reserved_mem: Accessor for acquiring reserved_mem
of/platform: Generalize /reserved-memory handling
soc: mediatek: pwrap: fix fatal compiler error
soc: mediatek: pwrap: fix compiler errors
arm64: mediatek: cleanup message for platform selection
soc: Allow test-building of MediaTek drivers
soc: mediatek: place Kconfig for all SoC drivers under menu
soc: mediatek: pwrap: add support for MT7622 SoC
soc: mediatek: pwrap: add common way for setup CS timing extenstion
soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap
..
The testcases.dts has purposely bad data which now generates a dtc warning:
drivers/of/unittest-data/testcases.dtb: Warning (interrupts_property): interrupts size is (4), expected multiple of 8 in /testcase-data/testcase-device2
Disable this warning for now. The proper solution is to split the unit
tests into good and bad data.
Signed-off-by: Rob Herring <robh@kernel.org>
Remove the manually added __local_fixups__ because dtc can now generate
them. This also fixes a new warning in the process:
drivers/of/unittest-data/testcases.dtb: Warning (interrupts_extended_property): Could not get phandle node for /__local_fixups__/testcase-data/interrupts/interrupts-extended0:interrupts-extended(cell 3)
Signed-off-by: Rob Herring <robh@kernel.org>
In the (relatively mechanical) process of adapting the RID-mapping code
to put the resulting ID in an output argument rather than the funtion
return value, we ended up with the debug print using the argument
pointer rather than the local value, which potentially defeats the
earlier NULL check.
Fixes: 987068fcbdb7: "of/irq: Break out msi-map lookup (again)"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture
doesn't support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
-----BEGIN PGP SIGNATURE-----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=ALJf
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture doesn't
support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
* tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: turn dma_cache_sync into a dma_map_ops method
sh: make dma_cache_sync a no-op
xtensa: make dma_cache_sync a no-op
unicore32: make dma_cache_sync a no-op
powerpc: make dma_cache_sync a no-op
mn10300: make dma_cache_sync a no-op
microblaze: make dma_cache_sync a no-op
ia64: make dma_cache_sync a no-op
frv: make dma_cache_sync a no-op
x86: make dma_cache_sync a no-op
floppy: consolidate the dummy fd_cacheflush definition
drivers: flag buses which demand DMA configuration
The fwnode_handle_get() function is used to obtain a reference to an
fwnode. A common usage pattern for the OF equivalent of the function is:
mynode = of_node_get(node);
Similarly make fwnode_handle_get() return the fwnode to which the
reference was obtained.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of DT files are compiled under arch/*/boot/dts/, but we have some
other directories, like drivers/of/unittest-data/. We often miss to
add gitignore patterns per directory. Since there are no source files
that end with .dtb or .dtb.S, we can ignore the patterns globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a node with no properties is dynamically added, then a property is
dynamically added to the node, then the property is dynamically removed,
the result will be node->properties == NULL and node->deadprops != NULL.
Add a separate function to release the properties in both lists.
Signed-off-by: Lixin Wang <alan.1.wang@nokia-sbell.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The Qualcomm remote file system protocol is used by certain remoteprocs,
in particular the modem, to read and write persistent storage in
platforms where only the application CPU has physical storage access.
The protocol is based on a set of QMI-encoded control-messages and a
shared memory buffer for exchaning the data. This driver implements the
latter, providing the user space service access to the carved out chunk
of memory.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
In some cases drivers referencing a reserved-memory region might want to
remap the entire region, but when defining the reserved-memory by "size"
the client driver has no means to know the associated base address of
the reserved memory region.
This patch adds an accessor for such drivers to acquire a handle to
their associated reserved-memory for this purpose.
A complicating factor for the implementation is that the reserved_mem
objects are created from the flattened DeviceTree, as such we can't
use the device_node address for comparison. Fortunately the name of the
node will be used as "name" of the reserved_mem and will be used when
building the full_name, so we can compare the "name" with the basename
of the full_name to find the match.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
By iterating over all /reserved-memory child nodes and match each one to
a list of compatibles that we want to treat specially, we can easily
extend the list of compatibles to handle - without having to resort to
of_platform_populate() that would create unnecessary platform_devices.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Pull networking fixes from David Miller:
"A little more than usual this time around. Been travelling, so that is
part of it.
Anyways, here are the highlights:
1) Deal with memcontrol races wrt. listener dismantle, from Eric
Dumazet.
2) Handle page allocation failures properly in nfp driver, from Jaku
Kicinski.
3) Fix memory leaks in macsec, from Sabrina Dubroca.
4) Fix crashes in pppol2tp_session_ioctl(), from Guillaume Nault.
5) Several fixes in bnxt_en driver, including preventing potential
NVRAM parameter corruption from Michael Chan.
6) Fix for KRACK attacks in wireless, from Johannes Berg.
7) rtnetlink event generation fixes from Xin Long.
8) Deadlock in mlxsw driver, from Ido Schimmel.
9) Disallow arithmetic operations on context pointers in bpf, from
Jakub Kicinski.
10) Missing sock_owned_by_user() check in sctp_icmp_redirect(), from
Xin Long.
11) Only TCP is supported for sockmap, make that explicit with a
check, from John Fastabend.
12) Fix IP options state races in DCCP and TCP, from Eric Dumazet.
13) Fix panic in packet_getsockopt(), also from Eric Dumazet.
14) Add missing locked in hv_sock layer, from Dexuan Cui.
15) Various aquantia bug fixes, including several statistics handling
cures. From Igor Russkikh et al.
16) Fix arithmetic overflow in devmap code, from John Fastabend.
17) Fix busted socket memory accounting when we get a fault in the tcp
zero copy paths. From Willem de Bruijn.
18) Don't leave opt->tot_len uninitialized in ipv6, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
stmmac: Don't access tx_q->dirty_tx before netif_tx_lock
ipv6: flowlabel: do not leave opt->tot_len with garbage
of_mdio: Fix broken PHY IRQ in case of probe deferral
textsearch: fix typos in library helpers
rxrpc: Don't release call mutex on error pointer
net: stmmac: Prevent infinite loop in get_rx_timestamp_status()
net: stmmac: Fix stmmac_get_rx_hwtstamp()
net: stmmac: Add missing call to dev_kfree_skb()
mlxsw: spectrum_router: Configure TIGCR on init
mlxsw: reg: Add Tunneling IPinIP General Configuration Register
net: ethtool: remove error check for legacy setting transceiver type
soreuseport: fix initialization race
net: bridge: fix returning of vlan range op errors
sock: correct sk_wmem_queued accounting on efault in tcp zerocopy
bpf: add test cases to bpf selftests to cover all access tests
bpf: fix pattern matches for direct packet access
bpf: fix off by one for range markings with L{T, E} patterns
bpf: devmap fix arithmetic overflow in bitmap_size calculation
net: aquantia: Bad udp rate on default interrupt coalescing
net: aquantia: Enable coalescing management via ethtool interface
...
If an Ethernet PHY is initialized before the interrupt controller it is
connected to, a message like the following is printed:
irq: no irq domain found for /interrupt-controller@e61c0000 !
However, the actual error is ignored, leading to a non-functional (POLL)
PHY interrupt later:
Micrel KSZ8041RNLI ee700000.ethernet-ffffffff:01: attached PHY driver [Micrel KSZ8041RNLI] (mii_bus:phy_addr=ee700000.ethernet-ffffffff:01, irq=POLL)
Depending on whether the PHY driver will fall back to polling, Ethernet
may or may not work.
To fix this:
1. Switch of_mdiobus_register_phy() from irq_of_parse_and_map() to
of_irq_get().
Unlike the former, the latter returns -EPROBE_DEFER if the
interrupt controller is not yet available, so this condition can be
detected.
Other errors are handled the same as before, i.e. use the passed
mdio->irq[addr] as interrupt.
2. Propagate and handle errors from of_mdiobus_register_phy() and
of_mdiobus_register_device().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same error string occurs in drivers/of/resolver.c. Change
the error here to more precisely describe this case, and avoid
the possible confusion of looking in the wrong source location
to understand the cause of an error.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
A device tree overlay notifier can return NOTIFY_OK, NOTIFY_STOP,
or an embedded errno. overlay_notify() incorrectly reports an
error for NOTIFY_OK.
Reported-by: atull@kernel.org
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
We do not want the common dma_configure() pathway to apply
indiscriminately to all devices, since there are plenty of buses which
do not have DMA capability, and if their child devices were used for
DMA API calls it would only be indicative of a driver bug. However,
there are a number of buses for which DMA is implicitly expected even
when not described by firmware - those we whitelist with an automatic
opt-in to dma_configure(), assuming that the DMA address space and the
physical address space are equivalent if not otherwise specified.
Commit 7232888366 ("of: restrict DMA configuration") introduced a
short-term fix by comparing explicit bus types, but this approach is far
from pretty, doesn't scale well, and fails to cope at all with bus
drivers which may be built as modules, like host1x. Let's refine things
by making that opt-in a property of the bus type, which neatly addresses
those problems and lets the decision of whether firmware description of
DMA capability should be optional or mandatory stay internal to the bus
drivers themselves.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
kbasename() will not return NULL if passed a valid string. If
the parameter passed to kbasename() in this case is already NULL
then the devicetree has been corrupted.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The "%pOF" printf format was recently added to print the
full name of a device tree node, with the intent of changing
the node full_name field to contain only the node name instead
of the full path of the node.
dup_and_fixup_symbol_prop() duplicates a property from the
"/__symbols__" node of an overlay device tree. The value
of each duplicated property must be fixed up to include
the full path of a node in the live device tree. The
current code uses the node's full_name for that purpose.
Update the code to use the "%pOF" printf format to
determine the node's full path.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The code to apply symbols from an overlay to the live device tree
was implemented with the intent to be minimally intrusive on the
existing code. After recent restructuring of the overlay apply
code, it is easier to disintangle the code that applies the
symbols, and to make the overlay changeset creation code more
straight forward and understandable.
Remove the extra complexity, and make the code more obvious.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The process of applying an overlay consists of:
- unflatten an overlay FDT (flattened device tree) into an
EDT (expanded device tree)
- fixup the phandle values in the overlay EDT to fit in a
range above the phandle values in the live device tree
- create the overlay changeset to reflect the contents of
the overlay EDT
- apply the overlay changeset, to modify the live device tree,
potentially changing the maximum phandle value in the live
device tree
There is currently no protection against two overlay applies
concurrently determining what range of phandle values are in use
in the live device tree, and subsequently changing that range.
Add a mutex to prevent multiple overlay applies from occurring
simultaneously.
Move of_resolve_phandles() into of_overlay_apply() so that it does not
have to be duplicated by each caller of of_overlay_apply().
The test in of_resolve_phandles() that the overlay tree is detached is
temporarily disabled so that old style overlay unittests do not fail.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When an overlay contains a node that already exists in
the live device tree, the overlay node is not allowed
to change the phandle of the existing node.
The existing check refused to allow an overlay node to
set the node phandle even when the existing node did
not have a phandle. Relax the check to allow an
overlay node to set the phandle value if the existing
node does not have a phandle.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The test of whether it is safe to remove an overlay changeset
looked at whether any node in the overlay changeset was in a
subtree rooted at any more recently applied overlay changeset
node.
The test failed to determine whether any node in the overlay
changeset was the root of a subtree that contained a more
recently applied overlay changeset node. Add this additional
check to the test.
The test is still lacking any check for any phandle dependencies.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When an attempt to apply an overlay changeset fails, an effort
is made to revert any partial application of the changeset.
When an attempt to remove an overlay changeset fails, an effort
is made to re-apply any partial reversion of the changeset.
The existing code does not check for failure to recover a failed
overlay changeset application or overlay changeset revert.
Add the missing checks and flag the devicetree as corrupt if the
state of the devicetree can not be determined.
Improve and expand the returned errors to more fully reflect the
result of the effort to undo the partial effects of a failed attempt
to apply or remove an overlay changeset.
If the device tree might be corrupt, do not allow further attempts
to apply or remove an overlay changeset.
When creating an overlay changeset from an overlay device tree,
add some additional warnings if the state of the overlay device
tree is not as expected.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Continue improving the readability of overlay.c. The previous patches
renamed identifiers. This patch is split out from the previous patches
to make the previous patches easier to review.
Changes are:
- minor code restructuring
- some initialization of an overlay changeset occurred outside of
init_overlay_changeset(), move that into init_overlay_changeset()
- consolidate freeing an overlay changeset into free_overlay_changeset()
This patch is intended to not introduce any functional change.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
More renaming of identifiers to better reflect what they do.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch is aimed primarily at drivers/of/overlay.c, but those
changes also have a small impact in a few other files.
overlay.c is difficult to read and maintain. Improve readability:
- Rename functions, types and variables to better reflect what
they do and to be consistent with names in other places,
such as the device tree overlay FDT (flattened device tree),
and make the algorithms more clear
- Use the same names consistently throughout the file
- Update comments for name changes
- Fix incorrect comments
This patch is intended to not introduce any functional change.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Use normal shorthand for comparing a variable to zero.
For variable "XXX":
convert (XXX == 0) to (!XXX)
convert (XXX != 0) to (XXX)
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Follows recommendations in Documentation/process/coding-style.rst,
section 8, Commenting.
Some in function comments are promoted to function header comments.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Function of_changeset_add_property or of_changeset_update_property may
fails. In this case the property just allocated is never deallocated.
Signed-off-by: Lixin Wang <alan.1.wang@nokia-sbell.com>
Signed-off-by: Rob Herring <robh@kernel.org>
of_fdt_unflatten_tree() already sets the flag on the node to
OF_DETACHED, because of_fdt_unflatten_tree() calls
__unflatten_device_tree() with the detached bool set to true.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This wasn't documented.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Save one line.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This is the same as be32_add_cpu(), so simplify the code and
remove the now unused local variable.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
For static DT usecases, we don't need the disabled nodes and can skip
unflattening. This saves a significant amount of RAM in memory constrained
cases. In one example on STM32F469, the RAM usage goes from 118K to 26K.
There are a few cases in the kernel that modify the status property
dynamically. These all are changes from enabled to disabled, depend on
OF_DYNAMIC or are not FDT based (PDT based).
Tested-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add an equivalent function to of_device_is_available for flattened DT, and
convert the one existing open coded occurrence.
Tested-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Having device_nodes be kobjects is only needed if sysfs or OF_DYNAMIC is
enabled. Otherwise, having a kobject in struct device_node is
unnecessary bloat in minimal kernel configurations.
Likewise, bin_attribute is only needed in struct property when sysfs is
enabled, so we can make it configurable too.
Tested-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rob Herring <robh@kernel.org>
The only user of kobj_to_device_node() is in dynamic.c, so move it
there. This avoids having to make it conditional once kobject is
configurable.
Tested-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rob Herring <robh@kernel.org>
The ref counting is broken for OF_DYNAMIC when sysfs is disabled because
the kobject initialization is skipped. Only the properties
add/remove/update should be skipped for !SYSFS config.
Tested-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rob Herring <robh@kernel.org>
Using CONFIG_OF_DYNAMIC=y uncovered an imbalance in the usecount of the
node being passed to of_fwnode_graph_get_port_parent(). Preserve the
usecount by using of_get_parent() instead of of_get_next_parent() which
don't decrement the usecount of the node passed to it.
Fixes: 3b27d00e7b ("device property: Move fwnode graph ops to firmware specific locations")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
There are two types of memory reservations firmware can ask the kernel
to make in the device tree: static and dynamic.
See Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
If you have greater than 16 entries in /reserved-memory (as we do on
POWER9 systems) you would get this scary looking error message:
[ 0.000000] OF: reserved mem: not enough space all defined regions.
This is harmless if all your reservations are static (which with OPAL on
POWER9, they are).
It is not harmless if you have any dynamic reservations after the 16th.
In the first pass over the fdt to find reservations, the child nodes of
/reserved-memory are added to a static array in of_reserved_mem.c so that
memory can be reserved in a 2nd pass. The array has 16 entries. This is why,
on my dual socket POWER9 system, I get that error 4 times with 20 static
reservations.
We don't have a problem on ppc though, as in arch/powerpc/kernel/prom.c
we look at the new style /reserved-ranges property to do reservations,
and this logic was introduced in 0962e8004e (well before any powernv
system shipped).
A Google search shows up no occurances of that exact error message, so we're
probably safe in that no machine that people use has memory not being reserved
when it should be.
The simple fix is to bump the length of the array to 32 which "should be
enough for everyone(TM)". The simple fix of not recording static allocations
in the array would cause problems for devices with "memory-region" properties.
A more future-proof fix is likely possible, although more invasive and this
simple fix is perfectly suitable in the meantime while a more future-proof
fix is developed.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Do not strdup() console options. It seems that the only reason for
it to be strdup()-ed was a compilation warning: printk, UART and
console drivers, for some reason, expect char pointer instead of
const char pointer. So we can just pass `of_stdout_options', but
need to cast it to char pointer. A better fix would be to change
printk, console drivers and UART to accept const char `options';
but that will take time - there are lots of drivers to update.
The patch also fixes a possible memory leak: add_preferred_console()
can fail, but we don't kfree() options.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Several host bridge drivers duplicate of_pci_range_parser_init() in order
to parse their dma-ranges property.
Provide of_pci_dma_range_parser_init() for that use case.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
With dependencies on a statically allocated full path name converted to
use %pOF format specifier, we can store just the basename of node, and
the unflattening of the FDT can be simplified.
This commit will affect the remaining users of full_name. After
analyzing these users, the remaining cases should only change some print
messages. The main users of full_name are providing a name for struct
resource. The resource names shouldn't be important other than providing
/proc/iomem names.
We no longer distinguish between pre and post 0x10 dtb formats as either
a full path or basename will work. However, less than 0x10 formats have
been broken since the conversion to use libfdt (and no one has cared).
The conversion of the unflattening code to be non-recursive also broke
pre 0x10 formats as the populate_node function would return 0 in that
case.
Signed-off-by: Rob Herring <robh@kernel.org>
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and
patches
-----BEGIN PGP SIGNATURE-----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=qHNs
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and patches
* tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping:
dma-coherent: fix dma_declare_coherent_memory() logic error
ARM: imx: mx31moboard: Remove unused 'dma' variable
dma-coherent: remove an unused variable
MAINTAINERS: use the iommu list for the dma-mapping subsystem
dma-coherent: remove the DMA_MEMORY_MAP and DMA_MEMORY_IO flags
dma-coherent: remove the DMA_MEMORY_INCLUDES_CHILDREN flag
of: restrict DMA configuration
dma-mapping: remove dma_alloc_noncoherent and dma_free_noncoherent
i825xx: switch to switch to dma_alloc_attrs
au1000_eth: switch to dma_alloc_attrs
sgiseeq: switch to dma_alloc_attrs
dma-mapping: reduce dma_mapping_error inline bloat
- Convert more DT code to use of_property_read_* API.
- Improve DT overlay support when adding multiple overlays.
- Convert printk's to %pOF format specifiers. Most went via subsystem
trees, but picked up the remaining orphans.
- Correct unittests to use preferred "okay" for "status" property value.
- Add a KASLR seed property.
- Vendor prefixes for Mellanox, Theobroma System, Adaptrum, Moxa.
- Fix modalias buffer handling.
- Clean-up of include paths for building dtbs.
- Add bindings for amc6821, isl1208, tsl2x7x, srf02, and srf10 devices.
- Add nvmem bindings for MediaTek MT7623 and MT7622 SoC.
- Add compatible string for Allwinner H5 Mali-450 GPU.
- Fix links to old OpenFirmware docs with new mirror on devicetree.org.
- Remove status property from binding doc examples.
-----BEGIN PGP SIGNATURE-----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=IBAh
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"There's a few orphans in the conversion to %pOF printf specifiers
included here that no one else picked up.
Summary:
- Convert more DT code to use of_property_read_* API.
- Improve DT overlay support when adding multiple overlays
- Convert printk's to %pOF format specifiers. Most went via subsystem
trees, but picked up the remaining orphans
- Correct unittests to use preferred "okay" for "status" property
value
- Add a KASLR seed property
- Vendor prefixes for Mellanox, Theobroma System, Adaptrum, Moxa
- Fix modalias buffer handling
- Clean-up of include paths for building dtbs
- Add bindings for amc6821, isl1208, tsl2x7x, srf02, and srf10
devices
- Add nvmem bindings for MediaTek MT7623 and MT7622 SoC
- Add compatible string for Allwinner H5 Mali-450 GPU
- Fix links to old OpenFirmware docs with new mirror on
devicetree.org
- Remove status property from binding doc examples"
* tag 'devicetree-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
devicetree: Adjust status "ok" -> "okay" under drivers/of/
dt-bindings: Remove "status" from examples
dt-bindings: pinctrl: sh-pfc: Use generic node name
dt-bindings: Add vendor Mellanox
dt-binding: net/phy: fix interrupts description
virt: Convert to using %pOF instead of full_name
macintosh: Convert to using %pOF instead of full_name
ide: pmac: Convert to using %pOF instead of full_name
microblaze: Convert to using %pOF instead of full_name
dt-bindings: usb: musb: Grammar s/the/to/, s/is/are/
of: Use PLATFORM_DEVID_NONE definition
of/device: Fix of_device_get_modalias() buffer handling
of/device: Prevent buffer overflow in of_device_modalias()
dt-bindings: add amc6821, isl1208 trivial bindings
dt-bindings: add vendor prefix for Theobroma Systems
of: search scripts/dtc/include-prefixes path for both CPP and DTC
of: remove arch/$(SRCARCH)/boot/dts from include search path for CPP
of: remove drivers/of/testcase-data from include search path for CPP
of: return of_get_cpu_node from of_cpu_device_node_get if CPUs are not registered
iio: srf08: add device tree binding for srf02 and srf10
...
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
- Introduce fwnode operations for all of the separate types of
"firmware nodes" that can be handled by the device properties
framework and drop the type field from struct fwnode_handle
(Sakari Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references
to the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework
to the new UUID API (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0rnk
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework, make the framework use const fwnode arguments all over, add
a helper for the consolidated handling of node references and switch
over the framework to the new UUID API.
Specifics:
- Introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework and drop the type field from struct fwnode_handle (Sakari
Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references to
the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework to the
new UUID API (Andy Shevchenko)"
* tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: device property: Switch to use new generic UUID API
device property: export irqchip_fwnode_ops
device property: Introduce fwnode_property_get_reference_args
device property: Constify fwnode property API
device property: Constify argument to pset fwnode backend
ACPI: Constify internal fwnode arguments
ACPI: Constify acpi_bus helper functions, switch to macros
ACPI: Prepare for constifying acpi_get_next_subnode() fwnode argument
device property: Get rid of struct fwnode_handle type field
ACPI: Use IS_ERR_OR_NULL() instead of non-NULL check in is_acpi_data_node()
Tweak a small number of status "ok" lines in a single file under
/drivers/of/ to use the proper DTSpec 0.1 spelling of "okay".
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Rob Herring <robh@kernel.org>
Moving DMA configuration to happen later at driver probe time had the
unnoticed side-effect that we now perform DMA configuration for *every*
device represented in DT, rather than only those explicitly created by
the of_platform and PCI code.
As Christoph points out, this is not really the best thing to do. Whilst
there may well be other DMA-capable buses that can benefit from having
their children automatically configured after the bridge has probed,
there are also plenty of others like USB, MDIO, etc. that definitely do
not support DMA and should not be indiscriminately processed.
The good news is that in most cases the DT "dma-ranges" property serves
as an appropriate indicator - per a strict interpretation of the spec,
anything lacking a "dma-ranges" property should be considered not to
have a mapping of DMA address space from its children to its parent,
thus anything for which of_dma_get_range() does not succeed does not
need DMA configuration. Certain bus types have a general expectation of
DMA capability and carry a well-established precedent that an absent
"dma-ranges" implies the same as the empty property, so we automatically
opt those in to DMA configuration regardless, to avoid regressing most
existing platforms.
Fixes: 09515ef5dd ("of/acpi: Configure dma operations at probe time for platform/amba/pci bus devices")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use dedicated definition instead of plain -1 where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
of_device_request_module() calls of_device_get_modalias() with "len" 0,
to calculate the size of the buffer needed to store the result, but due
to integer promotion the ssize_t "len" will be compared as unsigned with
strlen(compat) and the loop will generally never break. This results in
a call to snprintf() with a negative len, which triggers below warning,
followed by a dereference of a invalid pointer:
[ 3.060067] WARNING: CPU: 0 PID: 51 at lib/vsprintf.c:2122 vsnprintf+0x348/0x6d8
...
[ 3.060301] [<ffffff800891ede8>] vsnprintf+0x348/0x6d8
[ 3.060308] [<ffffff800891f248>] snprintf+0x48/0x50
[ 3.060316] [<ffffff80086a7c80>] of_device_get_modalias+0x108/0x160
[ 3.060322] [<ffffff80086a7cf8>] of_device_request_module+0x20/0x88
...
Further more of_device_get_modalias() is supposed to return the number
of bytes needed to store the entire modalias, so the loop needs to
continue accumulate the total size even though the buffer is full.
Finally the function is not expected to ensure space for the NUL, nor
include it in the returned size, so only 1 should be added to the length
of "compat" in the loop (to account for the character 'C').
Fixes: bc575064d6 ("of/device: use of_property_for_each_string to parse compatible strings")
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
As of_device_get_modalias() returns the number of bytes that would have
been written to the target string, regardless of how much did fit in the
buffer, it's possible that the returned index points beyond the buffer
passed to of_device_modalias() - causing memory beyond the buffer to be
null terminated.
Fixes: 0634c29589 ("of: Add function for generating a DT modalias with a newline")
Cc: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Historically, DMA masks have suffered some ambiguity between whether
they represent the range of physical memory a device can access, or the
address bits a device is capable of driving, particularly since on many
platforms the two are equivalent. Whilst there are some stragglers left
(dma_max_pfn(), I'm looking at you...), the majority of DMA code has
been cleaned up to follow the latter definition, not least since it is
the only one which makes sense once IOMMUs are involved.
In this respect, of_dma_configure() has always done the wrong thing in
how it generates initial masks based on "dma-ranges". Although rounding
down did not affect the TI Keystone platform where dma_addr + size is
already a power of two, in any other case it results in a mask which is
at best unnecessarily constrained and at worst unusable.
BCM2837 illustrates the problem nicely, where we have a DMA base of 3GB
and a size of 1GB - 16MB, giving dma_addr + size = 0xff000000 and a
resultant mask of 0x7fffffff, which is then insufficient to even cover
the necessary offset, effectively making all DMA addresses out-of-range.
This has been hidden until now (mostly because we don't yet prevent
drivers from simply overwriting this initial mask later upon probe), but
due to recent changes elsewhere now shows up as USB being broken on
Raspberry Pi 3.
Make it right by rounding up instead of down, such that the mask
correctly correctly describes all possisble bits the device needs to
emit.
Fixes: 9a6d7298b0 ("of: Calculate device DMA masks based on DT dma-range size")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Andreas Färber <afaerber@suse.de>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now, we can use of_graph_get_remote_endpoint(). Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Looks like gcc isn't always able to figure out that 3 *if* branches in
of_phy_register_fixed_link() calling fixed_phy_register() at their ends
are similar enough and thus can be merged. The "manual" merge saves 40
bytes of the object code (AArch64 gcc 4.8.5), and still saves 12 bytes
even if gcc was able to merge the branch tails (ARM gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "fixed-link" prop support predated of_property_read_u32_array(), so
basically had to open-code it. Using the modern API saves 24 bytes of the
object code (ARM gcc 4.8.5); the only behavior change would be that the
prop length check is now less strict (however the strict pre-check done
in of_phy_is_fixed_link() is left intact anyway)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiDoAAAoJEEg/ir3gV/o+594H/RH5kRwC719s/5YQFJXvGsVC
fjtj3UUJPLrWB8XBh7a4PRcxXPIHaFKJuY3MU7KHFIeZQFklJcit3njjpxDlUINo
F5S1LHBSYBkeMD/ksWBA8OLCBprNGN6WQ2tuFfAjZlQQ44zqv8LJmegoDtW9bGRy
aGAkjUmALEblQsq81y0BQwN2/8DA8HAywrs8L2dkH1LHwijoIeYMZFOtKugv1FbB
ABSKxcU7D/NYw6rsVdZG59fHFQ+eKOspDFqBZrUzfQ+zUU2hFFo96ovfXBfIqYCV
7BtJuKXu2LeGPzFLsuw4h1131iqFT1iSMy9fEhf/4OwaL/KPP/+Umy8vP/XfM+U=
=wCpd
-----END PGP SIGNATURE-----
Merge tag 'mlx5-shared-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-shared-2017-08-07
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the interrupts property parsing to use the OF property API
instead of open coding the parsing of the raw property value. This saves
a number of LoC, and the result is easier to read.
Signed-off-by: Rob Herring <robh@kernel.org>
Instead of directly parsing the compatible property, use the
of_property_for_each_string() helper to iterate over each compatible
string. This reduces the LoC and makes the functions easier to
understand.
Signed-off-by: Rob Herring <robh@kernel.org>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix inconsistent use of of_graph_get_port_parent() where
asoc_simple_card_parse_graph_dai() does of_node_get() before
calling it while other callers do not. We can fix this by
not trashing the node passed to of_graph_get_port_parent().
Let's also make sure the callers have correct refcounts and remove
related incorrect of_node_put() calls for of_for_each_phandle
as that's done by of_phandle_iterator_next() except when
we break out of the loop early.
Let's fix both issues with a single patch to avoid kobject
refcounts getting messed up more if two patches are merged
separately.
Otherwise strange issues can happen caused by memory corruption
caused by too many kobject_del() calls such as:
BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:747
...
(___might_sleep)
(__mutex_lock)
(mutex_lock_nested)
(kernfs_remove)
(kobject_del)
(kobject_put)
(of_get_next_parent)
(of_graph_get_port_parent)
(asoc_simple_card_parse_graph_dai [snd_soc_simple_card_utils])
(asoc_graph_card_probe [snd_soc_audio_graph_card])
Fixes: 0ef472a973 ("of_graph: add of_graph_get_port_parent()")
Fixes: 2692c1c63c ("ASoC: add audio-graph-card support")
Fixes: 1689333f83 ("ASoC: simple-card-utils: add asoc_simple_card_parse_graph_dai()")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_phy_register_fixed_link() declares the 'err' variable to hold the result
of of_property_read_string() but only uses it once after that, while that
function can be called directly from the *if* statement...
Remove that variable and move/regroup 'link_gpio' and 'len' variables in
order to sort the declarations in the reverse Xmas tree order -- to please
DaveM. ;-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_pci_get_devfn() and of_pci_parse_bus_range() somehow didn't use
of_property_read_u32_array() though it was long available, basically
open-coding it. Using the modern DT API saves several bytes and
also adds some prop sanity checks as a bonus...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Rob Herring <robh@kernel.org>
of_get_pci_domain_nr() somehow didn't use of_property_read_u32() though it
was long available, basically open-coding it. Using the modern DT API saves
several LoCs/bytes and also adds some prop sanity checks as a bonus...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Rob Herring <robh@kernel.org>
of_alias_scan() can use of_property_read_string() -- using the modern DT API
adds some prop sanity checks as a bonus; it does add couple LoCs but only
because the original code violated the 80-column limit...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Rob Herring <robh@kernel.org>
of_n_{addr|size}_cells() predate of_property_read_u32(), so they have to
basically open-code it. Using the modern DT API saves several LoCs and also
adds some prop sanity checks as a bonus...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The new fwnode_property_get_reference_args() interface amends the fwnode
property API with the functionality of both of_parse_phandle_with_args()
and __acpi_node_get_property_reference().
The semantics is slightly different: the cells property is ignored on ACPI
as the number of arguments can be explicitly obtained from the firmware
interface.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make fwnode arguments to the fwnode property API const.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of relying on the struct fwnode_handle type field, define
fwnode_operations structs for all separate types of fwnodes. To find out
the type, compare to the ops field to relevant ops structs.
This change has two benefits:
1. it avoids adding the type field to each and every instance of struct
fwnode_handle, thus saving memory and
2. makes the ops field the single factor that defines both the types of
the fwnode as well as defines the implementation of its operations,
decreasing the possibility of bugs when developing code dealing with
fwnode internals.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0, however of_irq_to_resource_table() still only regards 0 as
invalid IRQ -- fix it up.
Fixes: 7a4228bbff ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Rob Herring <robh@kernel.org>
It was never used and could be removed, otherwise
we could see a warning:
drivers/of/address.c: In function 'of_pci_range_parser_one':
drivers/of/address.c:277:14: warning: variable 'pci_space' set but not
used [-Wunused-but-set-variable]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The DT interrupt parsing code predates of_property_read_u32(), so it has to
basically open-code it. Using the modern DT API saves several LoCs and also
adds some prop sanity checks as a bonus...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The "interrupt-controller" property is boolean, i.e. has no value. The DT
interrupt parsing code predates of_property_read_bool(), so it uses either
of_get_property() or of_find_property() -- the former isn't quite correct
for the boolean props (but works somehow). Use the modern boolean prop API
instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add overlay __symbols__ properties to live tree when an overlay
is added to the live tree so that the symbols are available to
subsequent overlays.
Expected test result is new __symbols__ entries for labels from
the overlay after this commit.
Before this commit:
Console error message near end of unittest:
### dt-test ### FAIL of_unittest_overlay_high_level():2296 Adding overlay 'overlay_bad_symbol' failed
### dt-test ### end of unittest - 190 passed, 1 failed
The new unittest "fails" because the expected result of loading the
new overlay is an error instead of success.
$ # node hvac-medium-2 exists because the overlay loaded
$ # since the duplicate symbol was not detected
$ cd /proc/device-tree/testcase-data-2/substation@100/
$ ls
compatible hvac-medium-2 motor-8 reg
hvac-large-1 linux,phandle name status
hvac-medium-1 motor-1 phandle
$ cd /proc/device-tree/__symbols__/
$ ls
electric_1 lights_1 name rides_1 spin_ctrl_2
hvac_1 lights_2 retail_1 spin_ctrl_1
After this commit:
Previous console error message no longer occurs, but expected error
occurs:
OF: overlay: Failed to apply prop @/__symbols__/hvac_1
OF: overlay: apply failed '/__symbols__'
### dt-test ### end of unittest - 191 passed, 0 failed
$ # node hvac-medium-2 does not exist because the overlay
$ # properly failed to load due to the duplicate symbol
$ cd /proc/device-tree/testcase-data-2/substation@100/
$ ls
compatible hvac-medium-1 motor-1 name reg
hvac-large-1 linux,phandle motor-8 phandle status
$ cd /proc/device-tree/__symbols__/
$ ls
electric_1 lights_1 retail_1 ride_200_right spin_ctrl_2
hvac_1 lights_2 ride_200 rides_1
hvac_2 name ride_200_left spin_ctrl_1
$ cat ride_200; echo
/testcase-data-2/fairway-1/ride@200
$ cat ride_200_left ; echo
/testcase-data-2/fairway-1/ride@200/track@10
$ cat ride_200_right ; echo
/testcase-data-2/fairway-1/ride@200/track@20
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Correct existing node name detection when overlay node name has
a unit-address.
Expected test result is overlay will update the nodes and properties
for /testcase-data-2/fairway-1/ride@100/ after this commit.
Before this commit:
Console error message near end of unittest:
OF: Duplicate name in fairway-1, renamed to "ride@100#1"
$ cd /proc/device-tree/testcase-data-2/fairway-1/
$ # extra node: ride@100#1
$ ls
#address-cells linux,phandle phandle ride@200
#size-cells name ride@100 status
compatible orientation ride@100#1
$ cd /proc/device-tree/testcase-data-2/fairway-1/ride@100/
$ ls track@30/incline-up
ls: track@30/incline-up: No such file or directory
$ ls track@40/incline-up
ls: track@40/incline-up: No such file or directory
After this commit:
Console error message no longer occurs
$ cd /proc/device-tree/testcase-data-2/fairway-1/
$ # no extra node: ride@100#1
$ ls
#address-cells compatible name phandle ride@200
#size-cells linux,phandle orientation ride@100 status
$ cd /proc/device-tree/testcase-data-2/fairway-1/ride@100/
$ ls track@30/incline-up
track@30/incline-up
$ ls track@40/incline-up
track@40/incline-up
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add nodes and properties to overlay_base and overlay dts files to
test for
- incorrect existing node name detection when overlay node name
has a unit-address
- adding overlay __symbols__ properties to live tree when an
overlay is added to the live tree
The following console messages will appear near the end of unittest
until the code errors are corrected:
OF: Duplicate name in fairway-1, renamed to "ride@100#1"
### dt-test ### FAIL of_unittest_overlay_high_level():2296 Adding overlay 'overlay_bad_symbol' failed
### dt-test ### end of unittest - 190 passed, 1 failed
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
- Rearrange the core device properties code by moving the code
specific to each supported platform configuration framework
(ACPI, DT and build-in) into a separate file (Sakari Ailus).
- Add helper functions for accessing device properties in a
firmware-agnostic way (Sakari Ailus, Kieran Bingham).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EcrF
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These mostly rearrange the device properties core code and add a few
helper functions to it as a foundation for future work.
Specifics:
- Rearrange the core device properties code by moving the code
specific to each supported platform configuration framework (ACPI,
DT and build-in) into a separate file (Sakari Ailus).
- Add helper functions for accessing device properties in a
firmware-agnostic way (Sakari Ailus, Kieran Bingham)"
* tag 'devprop-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Add fwnode_graph_get_port_parent
device property: Add FW type agnostic fwnode_graph_get_remote_node
device property: Introduce fwnode_device_is_available()
device property: Move fwnode graph ops to firmware specific locations
device property: Move FW type specific functionality to FW specific files
ACPI: Constify argument to acpi_device_is_present()
- vsprintf format specifier %pOF for device_node's. This will enable us
to stop storing the full node names. Conversion of users will happen
next cycle.
- Update documentation to point to DT specification instead of ePAPR.
- Split out graph and property functions to a separate file.
- New of-graph functions for ALSA
- Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
Itead, and BananaPi.
- Improve dtx_diff utility filename printing.
-----BEGIN PGP SIGNATURE-----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=DNwf
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- vsprintf format specifier %pOF for device_node's. This will enable us
to stop storing the full node names. Conversion of users will happen
next cycle.
- Update documentation to point to DT specification instead of ePAPR.
- Split out graph and property functions to a separate file.
- New of-graph functions for ALSA
- Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
Itead, and BananaPi.
- Improve dtx_diff utility filename printing.
* tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (32 commits)
of: document /sys/firmware/fdt
dt-bindings: Add RISC-V vendor prefix
vsprintf: Add %p extension "%pOF" for device tree
of: find_node_by_full_name rewrite to compare each level
of: use kbasename instead of open coding
dt-bindings: thermal: add file extension to brcm,ns-thermal
of: update ePAPR references to point to Devicetree Specification
scripts/dtc: dtx_diff - Show real file names in diff header
of: detect invalid phandle in overlay
of: be consistent in form of file mode
of: make __of_attach_node() static
of: address.c header comment typo
of: fdt.c header comment typo
of: make of_fdt_is_compatible() static
dt-bindings: display-timing.txt convert non-ascii characters to ascii
Documentation: remove overlay-notes reference to non-existent file
dt-bindings: usb: exynos-usb: Add missing required VDD properties
dt-bindings: Add vendor prefix for Linksys
MAINTAINERS: add device tree ABI documentation file
of: Add vendor prefix for iWave Systems Technologies Pvt. Ltd
...
Russell King