Check the AFU state whenever an API is called. The hypervisor may
issue a reset of the adapter when it detects a fault. When it happens,
it launches an error recovery which will either move the AFU to a
permanent failure state, or in the disabled state.
If the AFU is found to be disabled, detach all existing contexts from
it before issuing a AFU reset to re-enable it.
Before detaching contexts, notify any kernel driver through the EEH
callbacks of the AFU pci device.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Like on bare-metal, the cxl driver creates a virtual PHB and a pci
device for the AFU. The configuration space of the device is mapped to
the configuration record of the AFU.
Reuse the code defined in afu_cr_read8|16|32() when reading the
configuration space of the AFU device.
Even though the (virtual) AFU device is a pci device, the adapter is
not. So a driver using the cxl kernel API cannot read the VPD of the
adapter through the usual PCI interface. Therefore, we add a call to
the cxl kernel API:
ssize_t cxl_read_adapter_vpd(struct pci_dev *dev, void *buf, size_t count);
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The new flash.c file contains the logic to flash a new image on the
adapter, through a hcall. It is an iterative process, with chunks of
data of 1M at a time. There are also 2 phases: write and verify. The
flash operation itself is driven from a user-land tool.
Once flashing is successful, an rtas call is made to update the device
tree with the new properties values for the adapter and the AFU(s)
Add a new char device for the adapter, so that the flash tool can
access the card, even if there is no valid AFU on it.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Filter out a few adapter parameters which don't make sense in a guest.
Document the changes.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The new of.c file contains code to parse the device tree to find out
about cxl adapters and AFUs.
guest.c implements the guest-specific callbacks for the backend API.
The process element ID is not known until the context is attached, so
we have to separate the context ID assigned by the cxl driver from the
process element ID visible to the user applications. In bare-metal,
the 2 IDs match.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
[mpe: Fix SMP=n build, fix PSERIES=n build, minor whitespace fixes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Introduce sub-structures containing the bare-metal specific fields in
the structures describing the adapter (struct cxl) and AFU (struct
cxl_afu).
Update all their references.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hypervisor calls provide an interface with a coherent platform
facility and function. It matches version 0.16 of the 'PAPR changes'
document.
The following hcalls are supported:
H_ATTACH_CA_PROCESS Attach a process element to a coherent platform
function.
H_DETACH_CA_PROCESS Detach a process element from a coherent
platform function.
H_CONTROL_CA_FUNCTION Allow the partition to manipulate or query
certain coherent platform function behaviors.
H_COLLECT_CA_INT_INFO Collect interrupt info about a coherent.
platform function after an interrupt occurred
H_CONTROL_CA_FAULTS Control the operation of a coherent platform
function after a fault occurs.
H_DOWNLOAD_CA_FACILITY Support for downloading a base adapter image to
the coherent platform facility, and for
validating the entire image after the download.
H_CONTROL_CA_FACILITY Allow the partition to manipulate or query
certain coherent platform facility behaviors.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A few functions are mostly common between bare-metal and guest and
just need minor tuning. To avoid crowding the backend API, introduce a
few 'if' based on the CPU being in HV mode.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename a few functions, changing the 'cxl_' prefix to either
'cxl_pci_' or 'cxl_native_', to make clear that the implementation is
bare-metal specific.
Those functions will have an equivalent implementation for a guest in
a later patch.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The backend API (in cxl.h) lists some low-level functions whose
implementation is different on bare-metal and in a guest. Each
environment implements its own functions, and the common code uses
them through function pointers, defined in cxl_backend_ops
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move a few functions around to better separate code specific to
bare-metal environment from code which will be commonly used between
guest and bare-metal.
Code specific to bare-metal is meant to be in native.c or pci.c
only. It's basically anything which touches the card p1 registers,
some p2 registers not needed from a guest and the PCI interface.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move around some functions which will be accessed from the bare-metal
and guest environments.
Code in native.c and pci.c is meant to be bare-metal specific.
Other files contain code which may be shared with guests.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Presently when a user-space process issues CXL_IOCTL_START_WORK ioctl we
store the pid of the current task_struct and use it to get pointer to
the mm_struct of the process, while processing page or segment faults
from the capi card. However this causes issues when the thread that had
originally issued the start-work ioctl exits in which case the stored
pid is no more valid and the cxl driver is unable to handle faults as
the mm_struct corresponding to process is no more accessible.
This patch fixes this issue by using the mm_struct of the next alive
task in the thread group. This is done by iterating over all the tasks
in the thread group starting from thread group leader and calling
get_task_mm on each one of them. When a valid mm_struct is obtained the
pid of the associated task is stored in the context replacing the
exiting one for handling future faults.
The patch introduces a new function named get_mem_context that checks if
the current task pointed to by ctx->pid is dead? If yes it performs the
steps described above. Also a new variable cxl_context.glpid is
introduced which stores the pid of the thread group leader associated
with the context owning task.
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reported-by: Frank Haverkamp <HAVERKAM@de.ibm.com>
Suggested-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An idr warning is reported when a context is release after the capi card
is unbound from the cxl driver via sysfs. Below are the steps to
reproduce:
1. Create multiple afu contexts in an user-space application using libcxl.
2. Unbind capi card from cxl using command of form
echo <capi-card-pci-addr> > /sys/bus/pci/drivers/cxl-pci/unbind
3. Exit/kill the application owning afu contexts.
After above steps a warning message is usually seen in the kernel logs
of the form "idr_remove called for id=<context-id> which is not
allocated."
This is caused by the function cxl_release_afu which destroys the
contexts_idr table. So when a context is release no entry for context pe
is found in the contexts_idr table and idr code prints this warning.
This patch fixes this issue by increasing & decreasing the ref-count on
the afu device when a context is initialized or when its freed
respectively. This prevents the afu from being released until all the
afu contexts have been released. The patch introduces two new functions
namely cxl_afu_get/put that manage the ref-count on the afu device.
Also the patch removes code inside cxl_dev_context_init that increases ref
on the afu device as its guaranteed to be alive during this function.
Reported-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cxl_free_afu_irqs() doesn't free IRQ names when it releases an AFU's IRQ
ranges. The userspace API equivalent in afu_release_irqs() calls
afu_irq_name_free() to release the IRQ names.
Call afu_irq_name_free() in cxl_free_afu_irqs() to release the IRQ names.
Make afu_irq_name_free() non-static to allow this.
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Fixes: 6f7f0b3df6 ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch configures the PSL Timebase function and enables it,
after the CAPP has been initialized by OPAL.
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The cxl user api uses the address_space associated with the file when we
need to force unmap all cxl mmap regions (e.g. on eeh, driver detach,
etc). Currently, contexts allocated through the kernel api do not do
this and instead skip the mmap invalidation, potentially allowing them
to poke at the hardware after such an event, which may cause all sorts
of trouble.
This patch allocates an address_space for cxl contexts allocated through
the kernel api so that the same invalidate path will for these contexts
as well. We don't use the anonymous inode's address_space, as doing so
could invalidate any mmaps of completely unrelated drivers using
anonymous file descriptors.
This patch also introduces a kernelapi flag, so we know when freeing the
context if the address_space was allocated by us and needs to be freed.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
userspace programs using cxl currently have to use two strategies for
dealing with MMIO errors simultaneously. They have to check every read
for a return of all Fs in case the adapter has gone away and the kernel
has not yet noticed, and they have to deal with SIGBUS in case the
kernel has already noticed, invalidated the mapping and marked the
context as failed.
In order to simplify things, this patch adds an alternative approach
where the kernel will return a page filled with Fs instead of delivering
a SIGBUS. This allows userspace to only need to deal with one of these
two error paths, and is intended for use in libraries that use cxl
transparently and may not be able to safely install a signal handler.
This approach will only work if certain constraints are met. Namely, if
the application is both reading and writing to an address in the problem
state area it cannot assume that a non-FF read is OK, as it may just be
reading out a value it has previously written. Further - since only one
page is used per context a write to a given offset would be visible when
reading the same offset from a different page in the mapping (this only
applies within a single context, not between contexts).
An application could deal with this by e.g. making sure it also reads
from a read-only offset after any reads to a read/write offset.
Due to these constraints, this functionality must be explicitly
requested by userspace when starting the context by passing in the
CXL_START_WORK_ERR_FF flag.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
EEH (Enhanced Error Handling) allows a driver to recover from the
temporary failure of an attached PCI card. Enable basic CXL support
for EEH.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide a kernel API and a sysfs entry which allow a user to specify
that when a card is PERSTed, it's image will stay the same, allowing
it to participate in EEH.
cxl_reset is used to reflash the card. In that case, we cannot safely
assert that the image will not change. Therefore, disallow cxl_reset
if the flag is set.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously the SPA was allocated and freed upon entering and leaving
AFU-directed mode. This causes some issues for error recovery - contexts
hold a pointer inside the SPA, and they may persist after the AFU has
been detached.
We would ideally like to allocate the SPA when the AFU is allocated, and
release it until the AFU is released. However, we don't know how big the
SPA needs to be until we read the AFU descriptor.
Therefore, restructure the code:
- Allocate the SPA only once, on the first attach.
- Release the SPA only when the entire AFU is being released (not
detached). Guard the release with a NULL check, so we don't free
if it was never allocated (e.g. dedicated mode)
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the PCI channel has gone down, don't attempt to poke the hardware.
We need to guard every time cxl_whatever_(read|write) is called. This
is because a call to those functions will dereference an offset into an
mmio register, and the mmio mappings get invalidated in the EEH
teardown.
Check in the read/write functions in the header.
We give them the same semantics as usual PCI operations:
- a write to a channel that is down is ignored.
- a read from a channel that is down returns all fs.
Also, we try to access the MMIO space of a vPHB device as part of the
PCI disable path. Because that's a read that bypasses most of our usual
checks, we handle it explicitly.
As far as user visible warnings go:
- Check link state in file ops, return -EIO if down.
- Be reasonably quiet if there's an error in a teardown path,
or when we already know the hardware is going down.
- Throw a big WARN if someone tries to start a CXL operation
while the card is down. This gives a useful stacktrace for
debugging whatever is doing that.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We're about to make these more complex, so make them functions
first.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch does two things.
Firstly it presents the Accelerator Function Unit (AFUs) behind the POWER
Service Layer (PSL) as PCI devices on a virtual PCI Host Bridge (vPHB). This
in in addition to the PSL being a PCI device itself.
As part of the Coherent Accelerator Interface Architecture (CAIA) AFUs can
provide an AFU configuration. This AFU configuration recored is architected to
be the same as a PCI config space.
This patch sets discovers the AFU configuration records, provides AFU config
space read/write functions to these configuration records. It then enumerates
the PCI bus. It also hooks in PCI ops where appropriate. It also destroys the
vPHB when the physical card is removed.
Secondly, it add an in kernel API for AFU to use CXL. AFUs must present a
driver that firstly binds as a PCI device. This PCI device can then be using
to do CXL specific operations (that can't sit in the PCI ops) using this API.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The cxl kernel API will allow drivers other than cxl to export a file
descriptor which has the same userspace API. These file descriptors will be
able to be used against libcxl.
This exports those file ops for use by other drivers.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the current include file from cxl.h -> cxl-base.h. This current
include file is used only to pass information between the base driver that
needs to be built into the kernel and the cxl module.
This is to make way for a new include/misc/cxl.h which will
contain just the kernel API for other driver to use
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Split the afu_register_irqs() function so that different parts can
be useful elsewhere.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export some symbols which will soon be used elsewhere in this driver.
Now they are global we rename them so to avoid collisions.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename cxl_afu_reset() to __cxl_afu_reset() to we can reuse this function name
in the API.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rework __detach_context() and cxl_context_detach() so we can reuse them in the
kernel API.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add cookie parameter to afu_release_irqs() so that we can pass in a different
cookie than the context structure. This will be useful for other kernel
drivers that want to call this but get their own cookie back in the interrupt
handler.
Update all existing call sites.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The afu fd release path was identified as a significant bottleneck in
the overall performance of cxl. While an optimal AFU design would
minimise the need to close & reopen the AFU fd, it is not always
practical to avoid.
The bottleneck seems to be down to the call to synchronize_rcu(), which
will block until every other thread is guaranteed to be out of an RCU
critical section. Replace it with call_rcu() to free the context
structures later so we can return to the application sooner.
This reduces the time spent in the fd release path from 13356 usec to
13.3 usec - about a 100x speed up.
Reported-by: Fei K Chen <uchen@cn.ibm.com>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export the "AFU Error Buffer" via sysfs attribute (afu_err_buf). AFU
error buffer is used by the AFU to report application specific
errors. The contents of this buffer are AFU specific and are intended to
be interpreted by the application interacting with the afu.
Suggested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Given a file descriptor on an afu device, libcxl currently uses the
major/minor number obtained from fstat on the fd to construct path to
the afu's sysfs directory. However it is possible that rather than using
one of the device in /dev/cxl, a kernel driver creates its own device
which export generic cxl interface to the userspace. This causes
problems with libcxl as it tries to use a wrong major/minor number to
construct the sysfs path and fail.
So this patch introduces a new ioctl called CXL_IOCTL_GET_AFU_ID on the
afu file descriptor to fetch the cxl_afu_id struct that holds the
card/offset-id and mode information. These info is then used by libcxl to
construct the correct path to the afu sysfs directory.
Testing:
- Build against pseries be/le configs
- Testing with corresponding libcxl changes to verify that it constructs
right sysfs path to the afu.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An AFU may optionally contain one or more PCIe like configuration
records, which can be used to identify the AFU.
This patch adds support for exposing the raw config space and the
vendor, device and class code under sysfs. These will appear in a
subdirectory of the AFU device corresponding with the configuration
record number, e.g.
cat /sys/class/cxl/afu0.0/cr0/vendor
0x1014
cat /sys/class/cxl/afu0.0/cr0/device
0x4350
cat /sys/class/cxl/afu0.0/cr0/class
0x120000
hexdump -C /sys/class/cxl/afu0.0/cr0/config
00000000 14 10 50 43 00 00 00 00 06 00 00 12 00 00 00 00 |..PC............|
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
00000100
These files behave in much the same way as the equivalent files for PCI
devices, with one exception being that the config file is currently
read-only and restricted to the root user. It is not necessarily
required to be this strict, but we currently do not have a compelling
use-case to make it writable and/or world-readable, so I erred on the
side of being restrictive.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Adds reset to sysfs which will PERST the card. If load_image_on_perst is set
to "user" or "factory", the PERST will cause that image to be loaded.
load_image_on_perst is set to "user" for production.
"none" could be used for debugging. The PSL trace arrays are preserved which
then can be read through debugfs.
PERST also triggers CAPP recovery. An HMI comes in, which is handled by EEH.
EEH unbinds the driver, calls into Sapphire to reinitialize the PHB, then
rebinds the driver.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Select defaults such that a PERST causes flash image reload. Select which
image based on what the card is set up to load.
CXL_VSEC_PERST_LOADS_IMAGE selects whether PERST assertion causes flash image
load.
CXL_VSEC_PERST_SELECT_USER selects which image is loaded on the next PERST.
cxl_update_image_control writes these bits into the VSEC.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Upon inspection of the implementation specific registers, it was
discovered that the high bit of the implementation specific RXCTL
register was enabled, which enables the DEADB00F debug feature.
The debug feature causes MMIO reads to a disabled AFU to respond with
0xDEADB00F instead of all Fs. In general this should not be visible as
the kernel will only allow MMIO access to enabled AFUs, but there may be
some circumstances where an AFU may become disabled while it is use.
One such case would be an AFU designed to only be used in the dedicated
process mode and to disable itself after it has completed it's work
(however even in that case the effects of this debug flag would be
limited as the userspace application must have completed any required
MMIO accesses before the AFU disables itself with or without the flag).
This patch removes the debug flag and replaces the magic value
programmed into this register with a preprocessor define so it is
clearer what the rest of this initialisation does.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If we need to force detach a context (e.g. due to EEH or simply force
unbinding the driver) we should prevent the userspace contexts from
being able to access the Problem State Area MMIO region further, which
they may have mapped with mmap().
This patch unmaps any mapped MMIO regions when detaching a userspace
context.
Cc: stable@vger.kernel.org
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We had a known sleep while atomic bug if a CXL device was forcefully
unbound while it was in use. This could occur as a result of EEH, or
manually induced with something like this while the device was in use:
echo 0000:01:00.0 > /sys/bus/pci/drivers/cxl-pci/unbind
The issue was that in this code path we iterated over each context and
forcefully detached it with the contexts_lock spin lock held, however
the detach also needed to take the spu_mutex, and call schedule.
This patch changes the contexts_lock to a mutex so that we are not in
atomic context while doing the detach, thereby avoiding the sleep while
atomic.
Also delete the related TODO comment, which suggested an alternate
solution which turned out to not be workable.
Cc: stable@vger.kernel.org
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently all interrupts generated by cxl are named "cxl". This is not very
informative as we can't distinguish between cards, AFUs, error interrupts, user
contexts and user interrupts numbers. Being able to distinguish them is useful
for setting affinity.
This patch gives each of these names in /proc/interrupts.
A two card CAPI system, with afu0.0 having 2 active contexts each with 4 user
IRQs each, will now look like this:
% grep cxl /proc/interrupts
444: 0 OPAL ICS 141312 Level cxl-card1-err
445: 0 OPAL ICS 141313 Level cxl-afu1.0-err
446: 0 OPAL ICS 141314 Level cxl-afu1.0
462: 0 OPAL ICS 2052 Level cxl-afu0.0-pe0-1
463: 75517 OPAL ICS 2053 Level cxl-afu0.0-pe0-2
468: 0 OPAL ICS 2054 Level cxl-afu0.0-pe0-3
469: 0 OPAL ICS 2055 Level cxl-afu0.0-pe0-4
470: 0 OPAL ICS 2056 Level cxl-afu0.0-pe1-1
471: 75506 OPAL ICS 2057 Level cxl-afu0.0-pe1-2
472: 0 OPAL ICS 2058 Level cxl-afu0.0-pe1-3
473: 0 OPAL ICS 2059 Level cxl-afu0.0-pe1-4
502: 1066 OPAL ICS 2050 Level cxl-afu0.0
514: 0 OPAL ICS 2048 Level cxl-card0-err
515: 0 OPAL ICS 2049 Level cxl-afu0.0-err
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If an AFU has a hardware bug that causes it to acknowledge a context
terminate or remove while that context has outstanding transactions, it
is possible for the kernel to receive an interrupt for that context
after we have removed it from the context list.
The kernel will not be able to demultiplex the interrupt (or worse - if
we have already reallocated the process handle we could mis-attribute it
to the new context), and printed a big scary warning.
It did not acknowledge the interrupt, which would effectively halt
further translation fault processing on the PSL.
This patch makes the warning clearer about the likely cause of the issue
(i.e. hardware bug) to make it obvious to future AFU designers of what
needs to be fixed. It also prints out the process handle which can then
be matched up with hardware and software traces for debugging.
It also acknowledges the interrupt to the PSL with either an address
error or acknowledge, so that the PSL can continue with other
translations.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is the core of the cxl driver.
It adds support for using cxl cards in the powernv environment only (ie POWER8
bare metal). It allows access to cxl accelerators by userspace using the
/dev/cxl/afuM.N char devices.
The kernel driver has no knowledge of the function implemented by the
accelerator. It provides services to userspace via the /dev/cxl/afuM.N
devices. When a program opens this device and runs the start work IOCTL, the
accelerator will have coherent access to that processes memory using the same
virtual addresses. That process may mmap the device to access any MMIO space
the accelerator provides. Also, reads on the device will allow interrupts to
be received. These services are further documented in a later patch in
Documentation/powerpc/cxl.txt.
Documentation of the cxl hardware architecture and userspace API is provided in
subsequent patches.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Lombard