Local variable 'autoneg' doesn't even exist:
drivers/net/phy/marvell.c: In function 'm88e1121_config_aneg':
drivers/net/phy/marvell.c:468:25: error: 'autoneg' undeclared (first use in this function); did you mean 'put_net'?
if (phydev->autoneg != autoneg || changed) {
^~~~~~~
Fixes: d6ab933647 ("net: phy: marvell: Avoid unnecessary soft reset")
Reported-by:Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BMCR.RESET bit on the Marvell PHYs has a special meaning in that
it commits the register writes into the HW for it to latch and be
configured appropriately. Doing software resets causes link drops, and
this is unnecessary disruption if nothing changed.
Determine from marvell_set_polarity()'s return code whether the register value
was changed and if it was, propagate that to the logic that hits the software
reset bit.
This avoids doing unnecessary soft reset if the PHY is configured in
the same state it was previously, this also eliminates the need for a
m88e1111_config_aneg() function since it now is the same as
marvell_config_aneg().
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While consolidating the PHY reset in phy_init_hw() an unconditionaly
BMCR soft-reset I became quite trigger happy with those. This was later
on deactivated for the Generic PHY driver on the premise that a prior
software entity (e.g: bootloader) might have applied workarounds in
commit 0878fff1f4 ("net: phy: Do not perform software reset for
Generic PHY").
Since we have a hook to wire-up a soft_reset callback, just use that and
get rid of the call to genphy_soft_reset() entirely. This speeds up
initialization and link establishment for most PHYs out there that do
not require a reset.
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When being in state PHY_HALTED we don't have to reschedule the
state machine, phy_start() will start it again.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.
This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_stop() may be called e.g. when suspending, therefore all needed
actions should be performed synchronously. Therefore add a synchronous
call to the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a network interface is created prior to the SFP socket being
available, ethtool can request module information. This unfortunately
leads to an oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = (ptrval)
[00000008] *pgd=7c400831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1480 Comm: ethtool Not tainted 4.19.0-rc3 #138
Hardware name: Broadcom Northstar Plus SoC
PC is at sfp_get_module_info+0x8/0x10
LR is at dev_ethtool+0x218c/0x2afc
Fix this by not filling in the network device's SFP bus pointer until
SFP is fully bound, thereby avoiding the core calling into the SFP bus
code.
Fixes: ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY_POLL is defined as -1 which means that we would be setting all flags of the
PHY driver, this is also not a valid flag to tell PHYLIB about, just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing in this driver which prevents it to be compiled for
other architectures. Add COMPILE_TEST so we get better compile test
coverage.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver indicates it can do 10/100 full and half duplex, plus 1G
Full. The datasheet indicates 1G half is also supported. So make use
of the standard PHY_GBIT_FEATURES.
It could be, this was added because there is a MAC which does not
support 1G half. Bit this is the wrong place to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY driver should not indicate that Pause is supported. It is upto
the MAC drive enable it, if it supports Pause frames. So remove it
from the ste10Xp driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all SFPs implement the registers containing sensor limits and
alarms. Luckily, there is a bit indicating if they are implemented or
not. Add checking for this bit, when deciding if the hwmon attributes
should be visible.
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the DT binding, it is specified nowhere that 'vsc8531,led-%d-mode' is
an u8, even though it's read as an u8 in the driver.
Let's update the driver to take into consideration that the
'vsc8531,led-%d-mode' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the DT binding, it is specified nowhere that 'vsc8531,edge-slowdown'
is an u8, even though it's read as an u8 in the driver.
Let's update the driver to take into consideration that the
'vsc8531,edge-slowdown' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the DT binding, it is specified nowhere that 'vsc8531,vddmac' is an
u16, even though it's read as an u16 in the driver.
Let's update the driver to take into consideration that the
'vsc8531,vddmac' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microsemi PHYs support different LED modes depending on the variant, so
let's factorize the code so we just have to give the supported modes
while the logic behind getting the mode remains identical.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LEDs modes are set the same way, except they are offset by 4 times the
index of the LED.
Let's factorize all the code so that it's easier to add support for the
4 LEDs of the VSC8584 PHY.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the code comment at the
top of the switch statement with a proper "fall through" annotation for
each case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 1056542 ("Missing break in switch")
Addresses-Coverity-ID: 1339579 ("Missing break in switch")
Addresses-Coverity-ID: 1369526 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the state numbers, device state, etc from numbers to strings
when printing debug messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for MAC drivers to use in their validate callback to deal
with 2500BaseX vs 1000BaseX modes, where the hardware supports both
but it is not possible to automatically select between them.
This helper defaults to 1000BaseX, as that is the 802.3 standard, and
will allow users to select 2500BaseX either by forcing the speed if
AN is disabled, or by changing the advertising mask if AN is enabled.
Disabling AN is not recommended as it is only the speed that we're
interested in controlling, not the duplex or pause mode parameters.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Omega SoC internal Combo Ethernet
GPHY to the bcm7xxx phy driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for suspend and resume to the Broadcom iProc mdio
mux driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to configure the internal rate adjust register based on the
core clock supplied through device tree in the Broadcom iProc mdio mux.
The operating frequency of the mdio mux block is 11MHz. This is derrived
by dividing the clock to the mdio mux with the rate adjust register.
In some SoC's the default values of the rate adjust register do not yield
11MHz. These SoC's are required to specify the clock via the device tree
for proper operation.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_mdiobus_alloc() instead of mdiobus_alloc() in the Broadcom
iProc mdio mux driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure the scan control register in the Broadcom iProc
mdio mux driver to disable access to external master.
In some SoC's, the scan control register defaults to an incorrect
value.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the register offsets in the Broadcom iProc mdio mux to start
from the top of the register address space.
Earlier, the base address pointed to the end of the block's register
space. The base address will now point to the start of the mdio's
address space. The offsets have been fixed to match this.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Extended Page Access is a 16-bit register, so change the page
parameter of vsc85xx_phy_page_set to a u16.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_mux_iproc_probe() uses platform_set_drvdata() to store md pointer
in device, whereas mdio_mux_iproc_remove() restores md pointer by
dev_get_platdata(&pdev->dev). This leads to wrong resources release.
The patch replaces getter to platform_get_drvdata.
Fixes: 98bc865a1e ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
m88e1116r_config_init() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking whether polling is used to detect PHY status
changes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_config_aneg() should be called only by PHYs that implement
the Clause 22 register set. Prevent Clause 45 PHYs that don't implement
the register set from calling the genphy function.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain PHY's have issues when operating in GBit slave mode and can
be forced to master mode. Examples are RTL8211C, also the Micrel PHY
driver has a DT setting to force master mode.
If two such chips are link partners the autonegotiation will fail.
Standard defines a self-clearing on read, latched-high bit to
indicate this error. Check this bit to inform the user.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"imply HWMON" was supposed to ensure that the SFP phy code can be built
with HWMON enabled or disabled while at the same time ensuring that
HWMON is not built as module if SFP is built into the kernel.
Unfortunately, that does not work as intended. With "allmodconfig", it
results in several unrelated HWMON drivers to be disabled instead of
being built as module as expected.
Let's use the old "depends on HWMON || HWMON=n" instead. This is slightly
different (it enforces SFP to be built as module if HWMON is built as
module), but it is better than the alternative of using "IS_REACHABLE()"
in the driver since that would disable sensor support if HWMON is built
as module and SFP is built into the kernel.
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The situation described in the comment can occur also with
PHY_IGNORE_INTERRUPT, therefore change the condition to include it.
Fixes: f555f34fdc ("net: phy: fix auto-negotiation stall due to unavailable interrupt")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver builds fine even with CONFIG_OF=n since we now have stubs that are
provided.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8366RB is an ASIC with five internal PHYs for
LAN0..LAN3 and WAN. The PHYs are spawn off the main
device so they can be handled in a distributed manner
by the Realtek PHY driver. All that is really needed
is the power save feature enablement and letting the
PHY driver core pick up the IRQ from the switch chip.
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP modules can contain a number of sensors. The EEPROM also contains
recommended alarm and critical values for each sensor, and indications
of if these have been exceeded. Export this information via
HWMON. Currently temperature, VCC, bias current, transmit power, and
possibly receiver power is supported.
The sensors in the modules can either return calibrate or uncalibrated
values. Uncalibrated values need to be manipulated, using coefficients
provided in the SFP EEPROM. Uncalibrated receive power values require
floating point maths in order to calibrate them. Performing this in
the kernel is hard. So if the SFP module indicates it uses
uncalibrated values, RX power is not made available.
With this hwmon device, it is possible to view the sensor values using
lm-sensors programs:
in0: +3.29 V (crit min = +2.90 V, min = +3.00 V)
(max = +3.60 V, crit max = +3.70 V)
temp1: +33.0°C (low = -5.0°C, high = +80.0°C)
(crit low = -10.0°C, crit = +85.0°C)
power1: 1000.00 nW (max = 794.00 uW, min = 50.00 uW) ALARM (LCRIT)
(lcrit = 40.00 uW, crit = 1000.00 uW)
curr1: +0.00 A (crit min = +0.00 A, min = +0.00 A) ALARM (LCRIT, MIN)
(max = +0.01 A, crit max = +0.01 A)
The scaling sensors performs on the bias current is not particularly
good. The raw values are more useful:
curr1:
curr1_input: 0.000
curr1_min: 0.002
curr1_max: 0.010
curr1_lcrit: 0.000
curr1_crit: 0.011
curr1_min_alarm: 1.000
curr1_max_alarm: 0.000
curr1_lcrit_alarm: 1.000
curr1_crit_alarm: 0.000
In order to keep the I2C overhead to a minimum, the constant values,
such as limits and calibration coefficients are read once at module
insertion time. Thus only reading *_input and *_alarm properties
requires i2c read operations.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing entry for RTL8211C to mdio_device_id table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: cf87915cb9 ("net: phy: realtek: add support for RTL8211C")
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers include functionality to speed down the PHY when
suspending and just waiting for a WoL packet because this saves energy.
This functionality is quite generic, therefore let's factor it out to
phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This functionality will also be needed in subsequent patches of this
series, therefore factor it out to a helper.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was been observed that with a particular order of initialisation,
the netdev can be up, but the SFP module still has its TX_DISABLE
signal asserted. This occurs when the network device brought up before
the SFP kernel module has been inserted by userspace.
This occurs because sfp-bus layer does not hear about the change in
network device state, and so assumes that it is still down. Set
netdev->sfp when the upstream is registered to work around this problem.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We fail to correctly clean up after a bus registration failure, which
can lead to an incorrect assumption about the registration state of
the upstream or sfp cage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The m88e1121 LED default configuration does not apply m88e151x.
So add a function to relpace m88e1121 LED configuration.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7385, VSC7388, VSC7395 and VSC7398 are integrated
switch/router chips for 5+1 or 8-port switches/routers. When
managed directly by Linux using DSA we need to do a special
set-up "dance" on the PHY. Unfortunately these sequences
switches the PHY to undocumented pages named 2a30 and 52b6
and does undocumented things. It is described by these opaque
sequences also in the reference manual. This is a best
effort to integrate it anyways.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SGMII was selected in the DT then the device should
write the SGMII enable bit.
If SGMII is not selected in the DT then the SGMII bit
should be disabled.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8211C has an issue when operating in Gigabit slave mode, therefore
genphy driver can't be used. See also this U-boot change.
https://lists.denx.de/pipermail/u-boot/2016-March/249712.html
Add a PHY driver for this chip with the quirk to force Gigabit master
mode. As a note: This will make it impossible to connect two network
ports directly which both are driven by a RTl8211C.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for RTL8211 I forgot to update the mdio_device_id
table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: d241d4aac9 ("net: phy: realtek: add support for RTL8211")
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where INT_STAT1 was written twice and
INT_STAT2 was ignored when disabling interrupts.
Fixes: b753a9faaf ("net: phy: DP83TC811: Introduce support for the DP83TC811 phy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of adding phylib support to the r8169 driver we need
PHY drivers for all chip-internal PHY types. Fortunately almost all
of them are either supported by the Realtek PHY driver already or work
with the genphy driver.
Still missing is support for the PHY of RTL8169s, it requires a quirk
to properly support 100Mbit-fixed mode. The quirk was copied from
r8169 driver which copied it from the vendor driver.
Based on the PHYID the internal PHY seems to be a RTL8211.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're ignoring the result of the attached phy device's read_status().
Return it so we can detect errors.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgmiitorgmii is using the mii_bus of the device it's attached to,
instead of the bus it was given during probe.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().
Fixes this Oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>] lr : [<c0529548>] psr: 20000013
sp : ce4cbb54 ip : 00000000 fp : ce4cbb8c
r10: 00000000 r9 : 00000000 r8 : c0c49178
r7 : 00000000 r6 : cdc14718 r5 : ce762800 r4 : cdc14710
r3 : 00000000 r2 : 00000054 r1 : 00000000 r0 : cdc14718
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002 f5d1f03c f5d1f05c f5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the quest to remove all stack VLA usage from the kernel[1], this
allocates the values buffer during the callback instead of putting it
on the stack.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When platform_device_register_simple() fails we can return
the error immediately instead of jumping to the 'err_pdev'
label.
This makes the error path a bit simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
The GPIO MDIO driver now needs only <linux/gpio/consumer.h>
so cut the legacy <linux/gpio.h> and <linux/of_gpio.h>
includes that are no longer used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DP83620 register set is compatible with the DP83848, but it also supports
100base-FX. When the hardware is configured such as that fiber mode is
enabled, autonegotiation is not possible.
The chip, however, doesn't expose this information via BMSR_ANEGCAPABLE.
Instead, this bit is always set high, even if the particular hardware
configuration makes it so that auto negotiation is not possible [1]. Under
these circumstances, the phy subsystem keeps trying for autonegotiation to
happen, without success.
Hereby, we inspect BMCR_ANENABLE bit after genphy_config_init, which on
reset is set to 0 when auto negotiation is disabled, and so we use this
value instead of BMSR_ANEGCAPABLE.
[1] https://e2e.ti.com/support/interface/ethernet/f/903/p/697165/2571170
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54612E have 4 multi-functional LED pins that can be configured
through register setting; the LED4 pin can be configured to a 125MHz
reference clock output by setting the spare register. Since the dedicated
CLK125 reference clock pin is not brought out on the 48-Pin MLP, the LED4
pin is the only pin to provide such function in this package, and therefore
it is beneficial to just enable the reference clock by default.
Signed-off-by: Kun Yi <kunyi@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of MDIO bus PM ops doesn't actually implement
bus-specific PM ops but just calls PM ops defined on a device level
what doesn't seem to be fully in line with the core PM model.
When looking e.g. at __device_suspend() the PM core looks for PM ops
of a device in a specific order:
1. device PM domain
2. device type
3. device class
4. device bus
I think it has good reason that there's no PM ops on device level.
Now that a device type representation of PHY's as special type of MDIO
devices was added (only user of MDIO bus PM ops), the MDIO bus
PM ops can be removed including member pm of struct mdio_device.
If for some other type of MDIO device PM ops are needed, it should be
modeled as struct device_type as well.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PHY is a type of MDIO device, so let's model it as struct device_type
and place PM ops, attribute groups and release callback on device type
level. For this the attribute definitions have to be moved.
This change allows us to get rid of the PM ops on a bus level in a second
step.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can bail out immediately also in case of PHY_IGNORE_INTERRUPT because
phy_mac_interupt() informs us once the link is up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613e ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently doing auxiliary control register reads with the shadow
register value 0b111 (0x7) which incidentally is also the selector value
that should be present in bits [2:0]. Fix this by using the appropriate
selector mask which is defined (MII_BCM54XX_AUXCTL_SHDWSEL_MASK).
This does not have a functional impact yet because we always access the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC (0x7) register in the current code.
This might change at some point though.
Fixes: 5b4e290051 ("net: phy: broadcom: add bcm54xx_auxctl_read")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the i2c-bus property mandatory when using a device
tree. If the sfp i2c bus isn't described it's impossible to guess the
protocol to use for a given module, and the sfp module would then not
work in most cases.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case no Tx disable pin is available the SFP modules will always be
emitting. This could be an issue when using modules using laser as their
light source as we would have no way to disable it when the fiber is
removed. This patch adds a warning when registering an SFP cage which do
not have its tx_disable pin wired or available.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_GPIOLIB is disabled, gpiod_put() becomes a stub that produces a
warning, this helped identify that we could be attempting to release a NULL
pl->link_gpio GPIO descriptor, so guard against that.
Fixes: daab3349ad ("net: phy: phylink: Release link GPIO")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those drivers build just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be
used as reference clock for the MAC unit. The clock signal must meet the
RGMII requirements to ensure the correct data transmission between the
MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle
requirement if the phy is configured as slave. For a complete
describtion look at the errata sheets: DS80000691D or DS80000692D.
The errata sheet recommends to force the phy into master mode whenever
there is a 1000Base-T link-up as work around. Only set the
"micrel,force-master" property if you use the phy reference clock provided
by CLK125_NDO pin as MAC reference clock in your application.
Attenation, this workaround is only usable if the link partner can
be configured to slave mode for 1000Base-T.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[m.felsch@pengutronix.de: fix dt-binding documentation]
[m.felsch@pengutronix.de: use already existing result var for read/write]
[m.felsch@pengutronix.de: add error handling]
[m.felsch@pengutronix.de: add more comments]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for the Microsemi MII Management controller (MIIM) found on
Microsemi SoCs.
On Ocelot, there are two controllers, one is connected to the internal
PHYs, the other one can communicate with external PHYs.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the DP83811 phy.
The DP83811 supports both rgmii and sgmii interfaces.
There are 2 part numbers for this the DP83TC811R does not
reliably support the SGMII interface but the DP83TC811S will.
There is not a way to differentiate these parts from the
hardware or register set. So this is controlled via the DT
to indicate which phy mode is required. Or the part can be
strapped to a certain interface.
Data sheet can be found here:
http://www.ti.com/product/DP83TC811S-Q1/descriptionhttp://www.ti.com/product/DP83TC811R-Q1/description
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a fixed link with a link GPIO, we need to poll that GPIO to
determine link state changes. This is consistent with what fixed_phy.c does.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not releasing the link GPIO descriptor with gpiod_put() which results in
subsequent probing to get -EBUSY when calling fwnode_get_named_gpiod(). Fix this
by doing the release in phylink_destroy().
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO provider for the link GPIO line might require the use of the
_cansleep() API, utilize that. This is safe to do since we run in workqueue
context.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for Microchip LAN87XX T1 PHYs
This patch support driver for Microchp T1 PHYs.
There will be followup patches to this driver to support T1 PHY
features such as cable diagnostics, signal quality indicator(SQI),
sleep and wakeup (TC10) support.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller