- Ensure that direct mapping alias is always flushed when changing page
attributes. The optimization for small ranges failed to do so when
the virtual address was in the vmalloc or module space.
- Unbreak the trace event registration for syscalls without arguments
caused by the refactoring of the SYSCALL_DEFINE0() macro.
- Move the printk in the TSC deadline timer code to a place where it is
guaranteed to only be called once during boot and cannot be rearmed by
clearing warn_once after boot. If it's invoked post boot then lockdep
rightfully complains about a potential deadlock as the calling context
is different.
- A series of fixes for objtool and the ORC unwinder addressing variety
of small issues:
Stack offset tracking for indirect CFAs in objtool ignored subsequent
pushs and pops
Repair the unwind hints in the register clearing entry ASM code
Make the unwinding in the low level exit to usermode code stop after
switching to the trampoline stack. The unwind hint is not longer valid
and the ORC unwinder emits a warning as it can't find the registers
anymore.
Fix the unwind hints in switch_to_asm() and rewind_stack_do_exit()
which caused objtool to generate bogus ORC data.
Prevent unwinder warnings when dumping the stack of a non-current
task as there is no way to be sure about the validity because the
dumped stack can be a moving target.
Make the ORC unwinder behave the same way as the frame pointer
unwinder when dumping an inactive tasks stack and do not skip the
first frame.
Prevent ORC unwinding before ORC data has been initialized
Immediately terminate unwinding when a unknown ORC entry type is
found.
Prevent premature stop of the unwinder caused by IRET frames.
Fix another infinite loop in objtool caused by a negative offset which
was not catched.
Address a few build warnings in the ORC unwinder and add missing
static/ro_after_init annotations
-----BEGIN PGP SIGNATURE-----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=0rCi
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Ensure that direct mapping alias is always flushed when changing
page attributes. The optimization for small ranges failed to do so
when the virtual address was in the vmalloc or module space.
- Unbreak the trace event registration for syscalls without arguments
caused by the refactoring of the SYSCALL_DEFINE0() macro.
- Move the printk in the TSC deadline timer code to a place where it
is guaranteed to only be called once during boot and cannot be
rearmed by clearing warn_once after boot. If it's invoked post boot
then lockdep rightfully complains about a potential deadlock as the
calling context is different.
- A series of fixes for objtool and the ORC unwinder addressing
variety of small issues:
- Stack offset tracking for indirect CFAs in objtool ignored
subsequent pushs and pops
- Repair the unwind hints in the register clearing entry ASM code
- Make the unwinding in the low level exit to usermode code stop
after switching to the trampoline stack. The unwind hint is no
longer valid and the ORC unwinder emits a warning as it can't
find the registers anymore.
- Fix unwind hints in switch_to_asm() and rewind_stack_do_exit()
which caused objtool to generate bogus ORC data.
- Prevent unwinder warnings when dumping the stack of a
non-current task as there is no way to be sure about the
validity because the dumped stack can be a moving target.
- Make the ORC unwinder behave the same way as the frame pointer
unwinder when dumping an inactive tasks stack and do not skip
the first frame.
- Prevent ORC unwinding before ORC data has been initialized
- Immediately terminate unwinding when a unknown ORC entry type
is found.
- Prevent premature stop of the unwinder caused by IRET frames.
- Fix another infinite loop in objtool caused by a negative
offset which was not catched.
- Address a few build warnings in the ORC unwinder and add
missing static/ro_after_init annotations"
* tag 'x86-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/orc: Move ORC sorting variables under !CONFIG_MODULES
x86/apic: Move TSC deadline timer debug printk
ftrace/x86: Fix trace event registration for syscalls without arguments
x86/mm/cpa: Flush direct map alias during cpa
objtool: Fix infinite loop in for_offset_range()
x86/unwind/orc: Fix premature unwind stoppage due to IRET frames
x86/unwind/orc: Fix error path for bad ORC entry type
x86/unwind/orc: Prevent unwinding before ORC initialization
x86/unwind/orc: Don't skip the first frame for inactive tasks
x86/unwind: Prevent false warnings for non-current tasks
x86/unwind/orc: Convert global variables to static
x86/entry/64: Fix unwind hints in rewind_stack_do_exit()
x86/entry/64: Fix unwind hints in __switch_to_asm()
x86/entry/64: Fix unwind hints in kernel exit path
x86/entry/64: Fix unwind hints in register clearing code
objtool: Fix stack offset tracking for indirect CFAs
Kristen found a hang in objtool when building with -ffunction-sections.
It was caused by evergreen_pcie_gen2_enable.cold() being laid out
immediately before evergreen_pcie_gen2_enable(). Since their "pfunc" is
always the same, find_jump_table() got into an infinite loop because it
didn't recognize the boundary between the two functions.
Fix that with a new prev_insn_same_sym() helper, which doesn't cross
subfunction boundaries.
Reported-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/378b51c9d9c894dc3294bc460b4b0869e950b7c5.1588110291.git.jpoimboe@redhat.com
When the current frame address (CFA) is stored on the stack (i.e.,
cfa->base == CFI_SP_INDIRECT), objtool neglects to adjust the stack
offset when there are subsequent pushes or pops. This results in bad
ORC data at the end of the ENTER_IRQ_STACK macro, when it puts the
previous stack pointer on the stack and does a subsequent push.
This fixes the following unwinder warning:
WARNING: can't dereference registers at 00000000f0a6bdba for ip interrupt_entry+0x9f/0xa0
Fixes: 627fce1480 ("objtool: Add ORC unwind table generation")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Reported-by: Dave Jones <dsj@fb.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Reported-by: Joe Mario <jmario@redhat.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/853d5d691b29e250333332f09b8e27410b2d9924.1587808742.git.jpoimboe@redhat.com
If func is NULL, a seg fault can result.
This is a theoretical issue which was found by Coverity, ID: 1492002
("Dereference after null check").
Fixes: c705cecc84 ("objtool: Track original function across branches")
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/afc628693a37acd287e843bcc5c0430263d93c74.1585761021.git.jpoimboe@redhat.com
If a switch jump table's indirect branch is in a ".cold" subfunction in
.text.unlikely, objtool doesn't detect it, and instead prints a false
warning:
drivers/media/v4l2-core/v4l2-ioctl.o: warning: objtool: v4l_print_format.cold()+0xd6: sibling call from callable instruction with modified stack frame
drivers/hwmon/max6650.o: warning: objtool: max6650_probe.cold()+0xa5: sibling call from callable instruction with modified stack frame
drivers/media/dvb-frontends/drxk_hard.o: warning: objtool: init_drxk.cold()+0x16f: sibling call from callable instruction with modified stack frame
Fix it by comparing the function, instead of the section and offset.
Fixes: 13810435b9 ("objtool: Support GCC 8's cold subfunctions")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/157c35d42ca9b6354bbb1604fe9ad7d1153ccb21.1585761021.git.jpoimboe@redhat.com
CONFIG_UBSAN_TRAP causes GCC to emit a UD2 whenever it encounters an
unreachable code path. This includes __builtin_unreachable(). Because
the BUG() macro uses __builtin_unreachable() after it emits its own UD2,
this results in a double UD2. In this case objtool rightfully detects
that the second UD2 is unreachable:
init/main.o: warning: objtool: repair_env_string()+0x1c8: unreachable instruction
We weren't able to figure out a way to get rid of the double UD2s, so
just silence the warning.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/6653ad73c6b59c049211bd7c11ed3809c20ee9f5.1585761021.git.jpoimboe@redhat.com
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
it's not really different from e.g. __sanitizer_cov_trace_cmp4();
as it is, the switches that generate an array of labels get
rejected by objtool, while slightly different set of cases
that gets compiled into a series of comparisons is accepted.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In preparation to adding a vmlinux.o specific pass, rearrange some
code. No functional changes intended.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20200324160924.924304616@infradead.org
Perf shows we spend a measurable amount of time spend cleaning up
right before we exit anyway. Avoid the needsless work and just
terminate.
This reduces objtool on vmlinux.o runtime from 5.4s to 4.8s
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20200324160924.800720170@infradead.org
Perf showed that __hash_init() is a significant portion of
read_sections(), so instead of doing a per section rela_hash, use an
elf-wide rela_hash.
Statistics show us there are about 1.1 million relas, so size it
accordingly.
This reduces the objtool on vmlinux.o runtime to a third, from 15 to 5
seconds.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20200324160924.739153726@infradead.org
Have it print a few numbers which can be used to size the hashtables.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20200324160924.321381240@infradead.org
Now that func_for_each_insn() is available, rename
func_for_each_insn_all(). This gets us:
sym_for_each_insn() - iterate on symbol offset/len
func_for_each_insn() - iterate on insn->func
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20200324160924.083720147@infradead.org
There is func_for_each_insn() and func_for_each_insn_all(), the both
iterate the instructions, but the first uses symbol offset/length
while the second uses insn->func.
Rename func_for_each_insn() to sym_for_eac_insn() because it iterates
on symbol information.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20200324160924.024341229@infradead.org
Trivial 'cleanup' to save one indentation level and match
validate_call().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20200324160923.963996225@infradead.org
A recent clang change, combined with a binutils bug, can trigger a
situation where a ".Lprintk$local" STT_NOTYPE symbol gets created at the
same offset as the "printk" STT_FUNC symbol. This confuses objtool:
kernel/printk/printk.o: warning: objtool: ignore_loglevel_setup()+0x10: can't find call dest symbol at .text+0xc67
Improve the call destination detection by looking specifically for an
STT_FUNC symbol.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/872
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=25551
Link: https://lkml.kernel.org/r/0a7ee320bc0ea4469bd3dc450a7b4725669e0ea9.1581997059.git.jpoimboe@redhat.com
Clang has the ability to create a switch table which is not a jump
table, but is rather a table of string pointers. This confuses objtool,
because it sees the relocations for the string pointers and assumes
they're part of a jump table:
drivers/ata/sata_dwc_460ex.o: warning: objtool: sata_dwc_bmdma_start_by_tag()+0x3a2: can't find switch jump table
net/ceph/messenger.o: warning: objtool: ceph_con_workfn()+0x47c: can't find switch jump table
Make objtool's find_jump_table() smart enough to distinguish between a
switch jump table (which has relocations to text addresses in the same
function as the original instruction) and other anonymous rodata (which
may have relocations to elsewhere).
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/485
Link: https://lkml.kernel.org/r/263f6aae46d33da0b86d7030ced878cb5cab1788.1581997059.git.jpoimboe@redhat.com
Relocations in alternative code can be dangerous, because the code is
copy/pasted to the text section after relocations have been resolved,
which can corrupt PC-relative addresses.
However, relocations might be acceptable in some cases, depending on the
architecture. For example, the x86 alternatives code manually fixes up
the target addresses for PC-relative jumps and calls.
So disallow relocations in alternative code, except where the x86 arch
code allows it.
This code may need to be tweaked for other arches when objtool gets
support for them.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Julien Thierry <jthierry@redhat.com>
Link: https://lkml.kernel.org/r/7b90b68d093311e4e8f6b504a9e1c758fd7e0002.1581359535.git.jpoimboe@redhat.com
When objtool encounters a fatal error, it usually means the binary is
corrupt or otherwise broken in some way. Up until now, such errors were
just treated as warnings which didn't fail the kernel build.
However, objtool is now stable enough that if a fatal error is
discovered, it most likely means something is seriously wrong and it
should fail the kernel build.
Note that this doesn't apply to "normal" objtool warnings; only fatal
ones.
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Julien Thierry <jthierry@redhat.com>
Link: https://lkml.kernel.org/r/f18c3743de0fef673d49dd35760f26bdef7f6fc3.1581359535.git.jpoimboe@redhat.com
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- Cross-arch changes to move the linker sections for NOTES and
EXCEPTION_TABLE into the RO_DATA area, where they belong on most
architectures. (Kees Cook)
- Switch the x86 linker fill byte from x90 (NOP) to 0xcc (INT3), to
trap jumps into the middle of those padding areas instead of
sliding execution. (Kees Cook)
- A thorough cleanup of symbol definitions within x86 assembler code.
The rather randomly named macros got streamlined around a
(hopefully) straightforward naming scheme:
SYM_START(name, linkage, align...)
SYM_END(name, sym_type)
SYM_FUNC_START(name)
SYM_FUNC_END(name)
SYM_CODE_START(name)
SYM_CODE_END(name)
SYM_DATA_START(name)
SYM_DATA_END(name)
etc - with about three times of these basic primitives with some
label, local symbol or attribute variant, expressed via postfixes.
No change in functionality intended. (Jiri Slaby)
- Misc other changes, cleanups and smaller fixes"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (67 commits)
x86/entry/64: Remove pointless jump in paranoid_exit
x86/entry/32: Remove unused resume_userspace label
x86/build/vdso: Remove meaningless CFLAGS_REMOVE_*.o
m68k: Convert missed RODATA to RO_DATA
x86/vmlinux: Use INT3 instead of NOP for linker fill bytes
x86/mm: Report actual image regions in /proc/iomem
x86/mm: Report which part of kernel image is freed
x86/mm: Remove redundant address-of operators on addresses
xtensa: Move EXCEPTION_TABLE to RO_DATA segment
powerpc: Move EXCEPTION_TABLE to RO_DATA segment
parisc: Move EXCEPTION_TABLE to RO_DATA segment
microblaze: Move EXCEPTION_TABLE to RO_DATA segment
ia64: Move EXCEPTION_TABLE to RO_DATA segment
h8300: Move EXCEPTION_TABLE to RO_DATA segment
c6x: Move EXCEPTION_TABLE to RO_DATA segment
arm64: Move EXCEPTION_TABLE to RO_DATA segment
alpha: Move EXCEPTION_TABLE to RO_DATA segment
x86/vmlinux: Move EXCEPTION_TABLE to RO_DATA segment
x86/vmlinux: Actually use _etext for the end of the text segment
vmlinux.lds.h: Allow EXCEPTION_TABLE to live in RO_DATA
...
The new check_zeroed_user() function uses variable shifts inside of a
user_access_begin()/user_access_end() section and that results in GCC
emitting __ubsan_handle_shift_out_of_bounds() calls, even though
through value range analysis it would be able to see that the UB in
question is impossible.
Annotate and whitelist this UBSAN function; continued use of
user_access_begin()/user_access_end() will undoubtedly result in
further uses of function.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: cyphar@cyphar.com
Cc: keescook@chromium.org
Cc: linux@rasmusvillemoes.dk
Fixes: f5a1a536fa ("lib: introduce copy_struct_from_user() helper")
Link: https://lkml.kernel.org/r/20191021131149.GA19358@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix the following warning seen on GCC 7.3:
kunit/test-test.o: warning: objtool: kunit_test_unsuccessful_try() falls through to next function kunit_test_catch()
kunit_try_catch_throw is a function added in the following patch in this
series; it allows KUnit, a unit testing framework for the kernel, to
bail out of a broken test. As a consequence, it is a new __noreturn
function that objtool thinks is broken (as seen above). So fix this
warning by adding kunit_try_catch_throw to objtool's noreturn list.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://www.spinics.net/lists/linux-kbuild/msg21708.html
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Explicitly check kvm_rebooting in kvm_spurious_fault() prior to invoking
BUG(), as opposed to assuming the caller has already done so. Letting
kvm_spurious_fault() be called "directly" will allow VMX to better
optimize its low level assembly flows.
As a happy side effect, kvm_spurious_fault() no longer needs to be
marked as a dead end since it doesn't unconditionally BUG().
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A clang build reported an (obvious) double CLAC while a GCC build did not;
it turns out that objtool only re-visits instructions if the first visit
was with AC=0. If OTOH the first visit was with AC=1, it completely ignores
any subsequent visit, even when it has AC=0.
Fix this by using a visited mask instead of a boolean, and (explicitly)
mark the AC state.
$ ./objtool check -b --no-fp --retpoline --uaccess drivers/gpu/drm/i915/gem/i915_gem_execbuffer.o
drivers/gpu/drm/i915/gem/i915_gem_execbuffer.o: warning: objtool: .altinstr_replacement+0x22: redundant UACCESS disable
drivers/gpu/drm/i915/gem/i915_gem_execbuffer.o: warning: objtool: eb_copy_relocations.isra.34()+0xea: (alt)
drivers/gpu/drm/i915/gem/i915_gem_execbuffer.o: warning: objtool: .altinstr_replacement+0xffffffffffffffff: (branch)
drivers/gpu/drm/i915/gem/i915_gem_execbuffer.o: warning: objtool: eb_copy_relocations.isra.34()+0xd9: (alt)
drivers/gpu/drm/i915/gem/i915_gem_execbuffer.o: warning: objtool: eb_copy_relocations.isra.34()+0xb2: (branch)
drivers/gpu/drm/i915/gem/i915_gem_execbuffer.o: warning: objtool: eb_copy_relocations.isra.34()+0x39: (branch)
drivers/gpu/drm/i915/gem/i915_gem_execbuffer.o: warning: objtool: eb_copy_relocations.isra.34()+0x0: <=== (func)
Reported-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/617
Link: https://lkml.kernel.org/r/5359166aad2d53f3145cd442d83d0e5115e0cd17.1564007838.git.jpoimboe@redhat.com
A Clang-built kernel is showing the following warning:
arch/x86/kernel/platform-quirks.o: warning: objtool: x86_early_init_platform_quirks()+0x84: unreachable instruction
That corresponds to this code:
7e: 0f 85 00 00 00 00 jne 84 <x86_early_init_platform_quirks+0x84>
80: R_X86_64_PC32 __x86_indirect_thunk_r11-0x4
84: c3 retq
This is a conditional retpoline sibling call, which is now possible
thanks to retpolines. Objtool hasn't seen that before. It's
incorrectly interpreting the conditional jump as an unconditional
dynamic jump.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/30d4c758b267ef487fb97e6ecb2f148ad007b554.1563413318.git.jpoimboe@redhat.com
This makes it easier to add new instruction types. Also it's hopefully
more robust since the compiler should warn about out-of-range enums.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/0740e96af0d40e54cfd6a07bf09db0fbd10793cd.1563413318.git.jpoimboe@redhat.com
This fixes objtool for both a GCC issue and a Clang issue:
1) GCC issue:
kernel/bpf/core.o: warning: objtool: ___bpf_prog_run()+0x8d5: sibling call from callable instruction with modified stack frame
With CONFIG_RETPOLINE=n, GCC is doing the following optimization in
___bpf_prog_run().
Before:
select_insn:
jmp *jumptable(,%rax,8)
...
ALU64_ADD_X:
...
jmp select_insn
ALU_ADD_X:
...
jmp select_insn
After:
select_insn:
jmp *jumptable(, %rax, 8)
...
ALU64_ADD_X:
...
jmp *jumptable(, %rax, 8)
ALU_ADD_X:
...
jmp *jumptable(, %rax, 8)
This confuses objtool. It has never seen multiple indirect jump
sites which use the same jump table.
For GCC switch tables, the only way of detecting the size of a table
is by continuing to scan for more tables. The size of the previous
table can only be determined after another switch table is found, or
when the scan reaches the end of the function.
That logic was reused for C jump tables, and was based on the
assumption that each jump table only has a single jump site. The
above optimization breaks that assumption.
2) Clang issue:
drivers/usb/misc/sisusbvga/sisusb.o: warning: objtool: sisusb_write_mem_bulk()+0x588: can't find switch jump table
With clang 9, code can be generated where a function contains two
indirect jump instructions which use the same switch table.
The fix is the same for both issues: split the jump table parsing into
two passes.
In the first pass, locate the heads of all switch tables for the
function and mark their locations.
In the second pass, parse the switch tables and add them.
Fixes: e55a73251d ("bpf: Fix ORC unwinding in non-JIT BPF code")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/e995befaada9d4d8b2cf788ff3f566ba900d2b4d.1563413318.git.jpoimboe@redhat.com
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Now that C jump tables are supported, call them "jump tables" instead of
"switch tables". Also rename some other variables, add comments, and
simplify the code flow a bit.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/cf951b0c0641628e0b9b81f7ceccd9bcabcb4bd8.1563413318.git.jpoimboe@redhat.com
Even calls to __noreturn functions need the frame pointer setup first.
Such functions often dump the stack.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/aed62fbd60e239280218be623f751a433658e896.1563413318.git.jpoimboe@redhat.com
dead_end_function() can no longer return an error. Simplify its
interface by making it return boolean.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/9e6679610768fb6e6c51dca23f7d4d0c03b0c910.1563413318.git.jpoimboe@redhat.com
- Add an alias check in validate_functions(). With this change, aliases
no longer need uaccess_safe set.
- Add an alias check in decode_instructions(). With this change, the
"if (!insn->func)" check is no longer needed.
- Don't create aliases for zero-length functions, as it can have
unexpected results. The next patch will spit out a warning for
zero-length functions anyway.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/26a99c31426540f19c9a58b9e10727c385a147bc.1563413318.git.jpoimboe@redhat.com
If 'insn->func' is NULL, objtool skips some important checks, including
sibling call validation. So if some .fixup code does an invalid sibling
call, objtool ignores it.
Treat all code branches (including alts) as part of the original
function by keeping track of the original func value from
validate_functions().
This improves the usefulness of some clang function fallthrough
warnings, and exposes some additional kernel bugs in the process.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/505df630f33c9717e1ccde6e4b64c5303135c25f.1563413318.git.jpoimboe@redhat.com
After an objtool improvement, it's reporting that __memcpy_mcsafe() is
calling mcsafe_handle_tail() with AC=1:
arch/x86/lib/memcpy_64.o: warning: objtool: .fixup+0x13: call to mcsafe_handle_tail() with UACCESS enabled
arch/x86/lib/memcpy_64.o: warning: objtool: __memcpy_mcsafe()+0x34: (alt)
arch/x86/lib/memcpy_64.o: warning: objtool: __memcpy_mcsafe()+0xb: (branch)
arch/x86/lib/memcpy_64.o: warning: objtool: __memcpy_mcsafe()+0x0: <=== (func)
mcsafe_handle_tail() is basically an extension of __memcpy_mcsafe(), so
AC=1 is supposed to be set. Add mcsafe_handle_tail() to the uaccess
safe list.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/035c38f7eac845281d3c3d36749144982e06e58c.1563413318.git.jpoimboe@redhat.com
The elftoolchain version of libelf has a function named elf_open().
The function name isn't quite accurate anyway, since it also reads all
the ELF data. Rename it to elf_read(), which is more accurate.
[ jpoimboe: rename to elf_read(); write commit description ]
Signed-off-by: Michael Forney <mforney@mforney.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/7ce2d1b35665edf19fd0eb6fbc0b17b81a48e62f.1562793604.git.jpoimboe@redhat.com
Objtool doesn't know how to read C jump tables, so it has to whitelist
functions which use them, causing missing ORC unwinder data for such
functions, e.g. ___bpf_prog_run().
C jump tables are very similar to GCC switch jump tables, which objtool
already knows how to read. So adding support for C jump tables is easy.
It just needs to be able to find the tables and distinguish them from
other data.
To allow the jump tables to be found, create an __annotate_jump_table
macro which can be used to annotate them.
The annotation is done by placing the jump table in an
.rodata..c_jump_table section. The '.rodata' prefix ensures that the data
will be placed in the rodata section by the vmlinux linker script. The
double periods are part of an existing convention which distinguishes
kernel sections from GCC sections.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Kairui Song <kasong@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lkml.kernel.org/r/0ba2ca30442b16b97165992381ce643dc27b3d1a.1561685471.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a function falls through to the next function due to a compiler
bug, objtool prints some obscure warnings. For example:
drivers/regulator/core.o: warning: objtool: regulator_count_voltages()+0x95: return with modified stack frame
drivers/regulator/core.o: warning: objtool: regulator_count_voltages()+0x0: stack state mismatch: cfa1=7+32 cfa2=7+8
Instead it should be printing:
drivers/regulator/core.o: warning: objtool: regulator_supply_is_couple() falls through to next function regulator_count_voltages()
This used to work, but was broken by the following commit:
13810435b9 ("objtool: Support GCC 8's cold subfunctions")
The padding nops at the end of a function aren't actually part of the
function, as defined by the symbol table. So the 'func' variable in
validate_branch() is getting cleared to NULL when a padding nop is
encountered, breaking the fallthrough detection.
If the current instruction doesn't have a function associated with it,
just consider it to be part of the previously detected function by not
overwriting the previous value of 'func'.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Fixes: 13810435b9 ("objtool: Support GCC 8's cold subfunctions")
Link: http://lkml.kernel.org/r/546d143820cd08a46624ae8440d093dd6c902cae.1557766718.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ignore flag is set on fake jumps in order to keep
add_jump_destinations() from setting their jump_dest, since it already
got set when the fake jump was created.
But using the ignore flag is a bit of a hack. It's normally used to
skip validation of an instruction, which doesn't really make sense for
fake jumps.
Also, after the next patch, using the ignore flag for fake jumps can
trigger a false "why am I validating an ignored function?" warning.
Instead just add an explicit check in add_jump_destinations() to skip
fake jumps.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/71abc072ff48b2feccc197723a9c52859476c068.1557766718.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull objtool updates from Ingo Molnar:
"This is a series from Peter Zijlstra that adds x86 build-time uaccess
validation of SMAP to objtool, which will detect and warn about the
following uaccess API usage bugs and weirdnesses:
- call to %s() with UACCESS enabled
- return with UACCESS enabled
- return with UACCESS disabled from a UACCESS-safe function
- recursive UACCESS enable
- redundant UACCESS disable
- UACCESS-safe disables UACCESS
As it turns out not leaking uaccess permissions outside the intended
uaccess functionality is hard when the interfaces are complex and when
such bugs are mostly dormant.
As a bonus we now also check the DF flag. We had at least one
high-profile bug in that area in the early days of Linux, and the
checking is fairly simple. The checks performed and warnings emitted
are:
- call to %s() with DF set
- return with DF set
- return with modified stack frame
- recursive STD
- redundant CLD
It's all x86-only for now, but later on this can also be used for PAN
on ARM and objtool is fairly cross-platform in principle.
While all warnings emitted by this new checking facility that got
reported to us were fixed, there might be GCC version dependent
warnings that were not reported yet - which we'll address, should they
trigger.
The warnings are non-fatal build warnings"
* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
mm/uaccess: Use 'unsigned long' to placate UBSAN warnings on older GCC versions
x86/uaccess: Dont leak the AC flag into __put_user() argument evaluation
sched/x86_64: Don't save flags on context switch
objtool: Add Direction Flag validation
objtool: Add UACCESS validation
objtool: Fix sibling call detection
objtool: Rewrite alt->skip_orig
objtool: Add --backtrace support
objtool: Rewrite add_ignores()
objtool: Handle function aliases
objtool: Set insn->func for alternatives
x86/uaccess, kcov: Disable stack protector
x86/uaccess, ftrace: Fix ftrace_likely_update() vs. SMAP
x86/uaccess, ubsan: Fix UBSAN vs. SMAP
x86/uaccess, kasan: Fix KASAN vs SMAP
x86/smap: Ditch __stringify()
x86/uaccess: Introduce user_access_{save,restore}()
x86/uaccess, signal: Fix AC=1 bloat
x86/uaccess: Always inline user_access_begin()
x86/uaccess, xen: Suppress SMAP warnings
...
This fixes the following warning seen on GCC 7.3:
arch/x86/kernel/dumpstack.o: warning: objtool: oops_end() falls through to next function show_regs()
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/3418ebf5a5a9f6ed7e80954c741c0b904b67b5dc.1554398240.git.jpoimboe@redhat.com
Having DF escape is BAD(tm).
Linus; you suggested this one, but since DF really is only used from
ASM and the failure case is fairly obvious, do we really need this?
OTOH the patch is fairly small and simple, so let's just do this
to demonstrate objtool's superior awesomeness.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is important that UACCESS regions are as small as possible;
furthermore the UACCESS state is not scheduled, so doing anything that
might directly call into the scheduler will cause random code to be
ran with UACCESS enabled.
Teach objtool too track UACCESS state and warn about any CALL made
while UACCESS is enabled. This very much includes the __fentry__()
and __preempt_schedule() calls.
Note that exceptions _do_ save/restore the UACCESS state, and therefore
they can drive preemption. This also means that all exception handlers
must have an otherwise redundant UACCESS disable instruction;
therefore ignore this warning for !STT_FUNC code (exception handlers
are not normal functions).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It turned out that we failed to detect some sibling calls;
specifically those without relocation records; like:
$ ./objdump-func.sh defconfig-build/mm/kasan/generic.o __asan_loadN
0000 0000000000000840 <__asan_loadN>:
0000 840: 48 8b 0c 24 mov (%rsp),%rcx
0004 844: 31 d2 xor %edx,%edx
0006 846: e9 45 fe ff ff jmpq 690 <check_memory_region>
So extend the cross-function jump to also consider those that are not
between known (or newly detected) parent/child functions, as
sibling-cals when they jump to the start of the function.
The second part of that condition is to deal with random jumps to the
middle of other function, as can be found in
arch/x86/lib/copy_user_64.S for example.
This then (with later patches applied) makes the above recognise the
sibling call:
mm/kasan/generic.o: warning: objtool: __asan_loadN()+0x6: call to check_memory_region() with UACCESS enabled
Also make sure to set insn->call_dest for sibling calls so we can know
who we're calling. This is useful information when printing validation
warnings later.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Really skip the original instruction flow, instead of letting it
continue with NOPs.
Since the alternative code flow already continues after the original
instructions, only the alt-original is skipped.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>