This patch adds the device ID for the bluetooth chip used in the
AMPAK AP6212 WiFi+Bluetooth module. The AP6212 is used on several
BananaPi boards, e.g. M2-Ultra.
The AP6212 is a combo module, where the WiFi chip is identified as
BCM43430A0 whereas the Bluetooth chip identifies itself as 4343A0. Note,
the missing '0' before the 'A0'.
The AP6212 needs a firmware blob. Loading the provided firmware file
from the BananaPi vendor, the adapter name is printed as
'BCM4343A0 26MHz AP6212_CL1-0061':
'''
hci0: Type: Primary Bus: UART
BD Address: 43:43:A0:12:1F:AC ACL MTU: 1021:8 SCO MTU: 64:1
UP RUNNING
RX bytes:3076 acl:0 sco:0 events:278 errors:0
TX bytes:39726 acl:0 sco:0 commands:279 errors:0
Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH SNIFF
Link mode: SLAVE ACCEPT
Name: 'BCM4343A0 26MHz AP6212_CL1-0061'
Class: 0x000000
Service Classes: Unspecified
Device Class: Miscellaneous,
HCI Version: 4.1 (0x7) Revision: 0xf2
LMP Version: 4.1 (0x7) Subversion: 0x2122
Manufacturer: Broadcom Corporation (15)
'''
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the device ID for the bluetooth chip used in the
Broadcom BCM4356 PCI-E WiFi / UART BT chip.
Successfully tested using Firmware version 0273
The upper nibble of the rev field is 2 on this device, so this commit
also adds handling of 2 to the switch-case done on the upper nibble.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The MINIX NEO Z83-4 and MINIX NEO Z83-4 Pro devices use an AP6255 chip
for wifi and bluetooth. Bluetooth requires an ACPI device id of BCM2EA4
with BCM4345 rev C0 firmware.
This patch defines the firmware subversion.
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The commands that read the basic vendor information about the Broadcom
controller are duplicated for UART and USB devices. Combine them into a
single function to reduce the code complexity.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the device ID for the bluetooth chip used in the
Broadcom BCM43430 SDIO WiFi / UART BT chip.
Successfully tested using Firmware version 0x0182
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reported-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some btbcm devices require more time to complete its reset process.
They won't reply any hci command until reset is done.
[ 17.218554] Bluetooth: hci0 command 0x1001 tx timeout
[ 25.214999] Bluetooth: hci0: BCM: Reading local version info failed (-110)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the call to request_firmware() fails in btbcm_setup_patchram(),
the BCM chip will be operating with its default firmware.
In this case, btbcm_setup_patchram() should not return immediately
but instead should skip to btbcm_check_bdaddr() and quirk setup.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the Apple Bluetooth devices, read the USB product information and
print them. This allows for easy mapping of chip and USB details.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The calculation for the firmware version number is off by one bit.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Broadcom Bluetooth controllers have the chip name included in the
ROM firmware or later in the patchram firmware. For debugging purposes
read the local name and print it out. This is only done during setup
stage and only once before loading the firmware and once after loading
the firmware.
For the Broadcom based controllers from Apple, the name is only read once
after determining the chip id.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The commit 7bee8b08c4 allows the Read Verbose Config Info to fail
gracefully and not cause the controller setup to abort. It seems the
reason that command failed in the first place was the missing HCI Reset
to bring the controller in full Bluetooth mode.
Apple Bluetooth controllers start out in HID mode and when in that mode
the Read Verbose Config Info command is not allowed. Sending HCI Reset
switches the controller into full HCI mode.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Commit 1c8ba6d013 moved around the setup code for broadcomm chips,
and also added btbcm_read_verbose_config() to read extra information
about the hardware. It's returning errors on some macbooks:
Bluetooth: hci0: BCM: Read verbose config info failed (-16)
Which makes us error out of the setup function. Since this
probe isn't critical to operate the chip, this patch just changes
things to carry on when it fails.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # v4.1
Support the BCM4354 chip and introduce vendor specific command
parameter definitions.
Signed-off-by: Ilya Faenson <ifaenson@broadcom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware loading may reset the controller UART speed and needs to set
host UART speed back to init speed.
UART drivers setup is split in 3 parts:
- btbcm_initialize() resets the controller and returns the firmware
name based on controller revision and sub_version.
- btbtcm_patchram() (already existing and public), which takes the
firmware name as parameter, requests the firmware and loads it to
the controller.
- btbcm_finalize() which resets the controller, reads local version
and checks if the controller address is a default one or not.
Remove firmware name retrieval for UART controllers from
btbcm_setup_patchram().
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move request/release_firmware() out of btbcm_patchram().
This allows a better error management, if request_firmware() returns an
error then the controller will be used without firmware loading and 0 is
returned.
This will imply to change btbcm_patchram() to accept a firmware instead
of firmware name.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove test of command reply status as it is already performed by
__hci_cmd_sync().
__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.
For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This isolates the Broadcom patchram download procedure as separate
function so that it can be easily used from USB and UART based drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Broadcom UART based devices seem to use a little bit different
firmare naming prefix. So add a separate table for these devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The quirks for Broadcom devices can be set from the setup function and
to keep the code simple, just move them into Broadcom support module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To unify the controller setup of Broadcom devices between USB and UART
transport, add the patchram download support into the Broadcom module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The majority of Broadcom Bluetooth vendor commands are shared between
USB and UART transports. This creates a separate module that eventually
will hold all Broadcom specific commands, but for now just start with
the commands to change the Bluetooth public address and check for the
default address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Jörg Krause