The btusb_read_local_version function has only a single user and with
that just move its functionality in place where it belongs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The __hci_cmd_sync function already handles the command status and
command complete errors. No need to check the status field again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SKB returned from the Intel specific version information command is
missing a kfree_skb.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Use btbcm helpers to perform controller setup.
Perform host UART reset to init speed between btbcm_patchram() and
btbcm_finalize(). This may be need because firmware loading may have
reseted controller UART to init speed.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware loading may reset the controller UART speed and needs to set
host UART speed back to init speed.
UART drivers setup is split in 3 parts:
- btbcm_initialize() resets the controller and returns the firmware
name based on controller revision and sub_version.
- btbtcm_patchram() (already existing and public), which takes the
firmware name as parameter, requests the firmware and loads it to
the controller.
- btbcm_finalize() which resets the controller, reads local version
and checks if the controller address is a default one or not.
Remove firmware name retrieval for UART controllers from
btbcm_setup_patchram().
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add initial and operational speeds.
Change to operational speed as soon as possible. If controller
set_baudrate() fails, continue at initial speed.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move request/release_firmware() out of btbcm_patchram().
This allows a better error management, if request_firmware() returns an
error then the controller will be used without firmware loading and 0 is
returned.
This will imply to change btbcm_patchram() to accept a firmware instead
of firmware name.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix spaces required around that '=' reported by checkpatch.
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-05-28
Here's a set of patches intended for 4.2. The majority of the changes
are on the 802.15.4 side of things rather than Bluetooth related:
- All sorts of cleanups & fixes to ieee802154 and related drivers
- Rework of tx power support in ieee802154 and its drivers
- Support for setting ieee802154 tx power through nl802154
- New IDs for the btusb driver
- Various cleanups & smaller fixes to btusb
- New btrtl driver for Realtec devices
- Fix suspend/resume for Realtek devices
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek btusb devices don't currently work after suspend/resume because
the updated firmware is quietly lost - the USB hub doesn't notice any
status change upon resume, but some kind of reset has definitely
happened as the LMP subversion has reverted to its original value.
Set the reset_resume flag to trigger probe and upload the new firmware
again.
Like the vendor code, I assume this is not needed when the device is
selected as a wakeup source and hence will retain power during suspend.
On the 2 products I have to hand, when trying this configuration the
hardware seems unable to keep the device powered up during suspend.
The USB hub then detects a status change on resume and does a reset,
so we do not end up in broken state.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The variables txcrc and hciextn are bool type. So assigning true
instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The reset is a bool type variable. So assigning true to reset instead
of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove test of command reply status as it is already performed by
__hci_cmd_sync().
__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.
For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove test of command reply status as it is already performed by
__hci_cmd_sync().
__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.
For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove test of command reply status as it is already performed by
__hci_cmd_sync().
__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.
For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As already done for btintel and btbcm export setup as separate function
in a vendor-specific module to hold all the Realtek specific commands.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes a compile warnning "dump_num maybe used uninitialized in
this function".
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove the DEBUG define as the debug code; so can remove mass debug info
from log buffer when using dmesg.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ">" should be ">=" so that we don't read past the end of the array.
Fixes: 9d9a113e3695 ('Bluetooth: btusb: Add Realtek 8723A/8723B/8761A/8821A support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ERROR: spaces required around that '<' (ctx:WxV)
+ if (err <0)
^
ERROR: code indent should use tabs where possible
+^I^I^I^I sizeof(ver));$
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Realtek ship a variety of bluetooth USB devices that identify
themselves with standard USB Bluetooth device class values, but
require a special driver to actually work. Without that driver,
you never get any scan results.
More recently however, Realtek appear to have wisened up and simply
posted a firmware update that makes these devices comply with
normal btusb protocols. The firmware needs to be uploaded on each boot.
Based on Realtek code from https://github.com/lwfinger/rtl8723au_bt
('new' branch).
This enables bluetooth support in the Gigabyte Brix GB-BXBT-2807 which
has this RTL8723BE USB device:
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3410 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
There is no change to the USB descriptor after firmware update,
however the version read by HCI_OP_READ_LOCAL_VERSION changes from
0x8723 to 0x3083.
This has also been tested on RTL8723AE and RTL8821AE. Support for
RTL8761A has also been added, but that is untested.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Atheros support for missing the support for configuration of the
Bluetooth public address. Add support for the vendor specific command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The driver callbacks in the Atheros support were all in a random order
and did not help readability of this driver. So reorder them to make
them aligned with what other Bluetooth UART drivers do. This patch is
not changing any actual code.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This isolates the Broadcom patchram download procedure as separate
function so that it can be easily used from USB and UART based drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
I think the comments are used to debug, and we don't need them in
mainline code
Signed-off-by: DingXiang <dingxiang@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel vendors events indicating firmware loading result and the
bootup of the operational firmware are currently hardcoded byte
comparisons. So intead of doing that, provide proper data structures
and actually use them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth address setting for Intel devices is provided by a generic
module now. Start using that module instead of relying it being included
in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the Intel Bluetooth support has its own header, it makes sense
to move all command structs into it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth address handling for Intel devices is provided by a generic
module now. Start using that module instead of relying it being included
in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The majority of Intel Bluetooth vendor commands are shared between USB
and UART transports. This creates a separate module that eventually
will hold all Intel specific commands, but for now just start with the
commands to change the Bluetooth public address and check for the
default address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Future H:4 based UART drivers require custom packet types and custom
receive functions. To support this, extended the h4_recv_buf function
with a packet definition table.
For the default H:4 packets types of ACL data, SCO data and events,
provide helpers to reduce the amount of code duplication.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Broadcom UART based devices seem to use a little bit different
firmare naming prefix. So add a separate table for these devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the protocol support for Broadcom based UART devices to
enable firmware and patchram download procedure. It is a pretty
straight forward H:4 driver with the exception of actually having
its own setup and address configuration callbacks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The setup callback got wrongly inserted between the enqueue and dequeue
callbacks. Move it to a better location.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The version number is cosmetic, but pretty handy for debugging purposes
and since the Broadcom protocol support is now optional, just increase
it to indicate the difference.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The quirks for Broadcom devices can be set from the setup function and
to keep the code simple, just move them into Broadcom support module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the generic Broadcom Bluetooth support module, it is possible to
turn support for firmware and patchram download into an optional
feature.
To keep backwards compatibility with previous kernel configurations,
the new option defaults to enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To unify the controller setup of Broadcom devices between USB and UART
transport, add the patchram download support into the Broadcom module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new Broadcom Bluetooth support module provides generic functionality
for changing and checking the Bluetooth device address. Use these new
features instead of keeping a duplicate in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new Broadcom Bluetooth support module provides generic functionality
for changing and checking the Bluetooth device address. Use these new
features instead of keeping a duplicate in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The majority of Broadcom Bluetooth vendor commands are shared between
USB and UART transports. This creates a separate module that eventually
will hold all Broadcom specific commands, but for now just start with
the commands to change the Bluetooth public address and check for the
default address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This version number is more cosmetic and for debugging purposes, but
since there has been a few changes lately, increase it now.
Two left-over and not used version constants that were never exposed
anywhere are removed since they have no actual value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The init function for each HCI UART protocol prints the same on success
and failure. This information is so generic, remove it and let the main
HCI UART handling print it instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds an extra name field to the hci_uart_proto struct that provides
a simple way of adding a string identifier to the protocol.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The usage of struct hci_uart_proto should always be const. Change the
function headers and individual protocol drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of using hci_recv_stream_fragment, use the local available
h4_recv_buf helper function.
To ensure that the function is available select BT_HCIUART_H4.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of using hci_recv_stream_fragment, use the local available
h4_recv_buf helper function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The h4_recv_buf helper function can be used for receiving H:4 packets
out of a TTY stream. It is self-contained and allows for reuse by all
HCI UART protocols.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The TTY layer provides its data pointers as const, but the HCI UART
callbacks expect them as general data pointers. This is of course
wrong and instead of casting them, just fix the individual drivers
to actually take a const data pointer.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The fields h4->rx_state and h4->rx_count are not used at all and with
that they can be just removed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The h4->rx_skb is not used anymore and with that just remove it. Seems
this was a leftover and even the kfree_skb call freeing it is rather
pointless since it got never allocated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Casting the tty->disc_data to (void *) is not needed at all. So just
remove this cast and assign the object without a cast.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using vendor detection, this adds support for the Broadcom
specific address configuration command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using vendor detection, this adds support for the Intel specific
address configuration command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a new HCI_UART_VND_DETECT flag to allow automatic vendor
detection. This allows to enable known vendor commands (for example
for setting the public device address) when using a standard H:4
UART protocol or when running in virtual machines.
When this new flag is configured and no vendor specific setup
routine is provided, then the local version information are read
and the provided manufacturer information can be evaluated to
configure extra vendor callbacks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For all modern Bluetooth USB devices from Broadcom it makes a lot more
sense to use USB_VENDOR_AND_INTERFACE_INFO instead of manually adding
USB_DEVICE for each one of them. There are already interface entries
for these vendors and so just remove the duplicate device entries.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Bluetooth controllers require initialization before being
used (vendor config, firmware download). Add possibility for a
HCI UART proto to implement this early init via the setup callback.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the Apple Bluetooth devices that are Broadcom based, it makes sense
to read the chip information. It is a single HCI command and might help
gathering more information about these devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Broadcom devices expose their chip id via Read Verbose Config
Version Info command. While this information is not used at the
moment, it might be useful for debugging purposes and so read it
before patching the firmware. This makes it show up in dmesg and
HCI traces taken for the system.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
CSR controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Intel controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Atheros controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg says:
====================
Here's another set of Bluetooth & ieee802154 patches intended for 4.1:
- Added support for QCA ROME chipset family in the btusb driver
- at86rf230 driver fixes & cleanups
- ieee802154 cleanups
- Refactoring of Bluetooth mgmt API to allow new users
- New setting for static Bluetooth address exposed to user space
- Refactoring of hci_dev flags to remove limit of 32
- Remove unnecessary fast-connectable setting usage restrictions
- Fix behavior to be consistent when trying to pair already paired device
- Service discovery corner-case fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple codepaths duplicate some simple code to read and
sanity-check local version information. Before I add a couple more
such codepaths, add a helper to reduce duplication.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
While qca_device_info is not coming from outside communication,
no reason to use specific endian type inside and fix the wrong
version comparison on big-endian platform.
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of chipset does not allow to send a patch or config files through
HCI VS channel at early stage as well as they don't support to send
USB patch files to other channel except USB bulk path.
New callback added is for initialization of BT controller through USB
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-02
Here's the first bluetooth-next pull request targeting the 4.1 kernel:
- ieee802154/6lowpan cleanups
- SCO routing to host interface support for the btmrvl driver
- AMP code cleanups
- Fixes to AMP HCI init sequence
- Refactoring of the HCI callback mechanism
- Added shutdown routine for Intel controllers in the btusb driver
- New config option to enable/disable Bluetooth debugfs information
- Fix for early data reception on L2CAP fixed channels
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtgkACgkQMUfUDdst+ykXbACg14oFAmeYjO9RsdIHPXBvKseO
47QAn0foy91bpNQ5UFOxWS5L6Fzj2ZND
=syx2
-----END PGP SIGNATURE-----
Merge tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as
well. All have been in linux-next with no reported issues"
* tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: 8250: Fix UART_BUG_TXEN workaround
serial: driver for ETRAX FS UART
tty: remove unused variable sprop
serial: of-serial: fetch line number from DT
serial: samsung: earlycon support depends on CONFIG_SERIAL_SAMSUNG_CONSOLE
tty/serial: serial8250_set_divisor() can be static
tty/serial: Add Spreadtrum sc9836-uart driver support
Documentation: DT: Add bindings for Spreadtrum SoC Platform
serial: samsung: remove redundant interrupt enabling
tty: Remove external interface for tty_set_termios()
serial: omap: Fix RTS handling
serial: 8250_omap: Use UPSTAT_AUTORTS for RTS handling
serial: core: Rework hw-assisted flow control support
tty/serial: 8250_early: Add support for PXA UARTs
tty/serial: of_serial: add support for PXA/MMP uarts
tty/serial: of_serial: add DT alias ID handling
serial: 8250: Prevent concurrent updates to shadow registers
serial: 8250: Use canary to restart console after suspend
serial: 8250: Refactor XR17V35X divisor calculation
serial: 8250: Refactor divisor programming
...
The Broadcom firmware files are named with firmware version information
encoded into lmp_subver field. So BCM20702B0_002.001.014.0527.0607.hex
would be represented by 0x410e. To allow for an easier decoding of the
actual firmware names, provide an internal table that does the mapping
and request the firmware file by name.
Bluetooth: hci0: BCM20702B0 (002.001.014) build 0607
Now the complicated encoding of lmp_subver will be decoded and turned
into the name and firmware version information from the firmware files.
The previous attempt of using udev->product failed badly since it never
contains any matching entry to the actual hardware or firmware files
distributed by Broadcom in their Windows drivers. It is even worse since
it can change depending on if the internal bootstrapping happened before
the USB bus enumeration or after. This caused many race conditions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the device shutdown routine for Intel Bluetooth device.
Some platforms have BT LED issue with Intel Bluetooth device that BT LED goes
off 5 seconds after BT is turned off
For Intel Bluetooth device, the BT LED is turned off when:
- there is no active connection or radio activity
- USB is suspend
So, when the BT is turned off, it takes 5 seconds because USB suspend timeone
is 5 seconds by default. And if the USB suspend is not enabled, BT LED won't be
turned off.
To fix this issue, recently Intel Bluetooth firmware patch had been submitted
to turn off the BT LED immediately by the vendor specific command(0xFC3F). And
this patch sends this command to the device before closing the device.
For backward compatibility of this command with old firmware, this command was
supported before, but it behaves same as HCI_RESET internally. So, it won't be
the problem even if the system doesn't have the latest firmware patch.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's now a proper wait_on_bit_timeout() API in linux/wait.h so we can
remove our own copy from btusb.c. Our copy had the task state and
timeout variables swapped so the patch also changes their order.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A vendor specific command is sent to firmware during
initialization to enable this feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
tty_set_termios() is an internal helper intended for file scope use.
UART drivers which are capable of driving the RTS pin must
properly handle the tiocmset() method, regardless of termios settings.
A failure to do so is a UART driver bug and should be fixed there.
Do not use this interface to workaround UART driver bugs.
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: <linux-bluetooth@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel Snowfield Peak Bluetooth controllers use a strict scanning
filter policy that filters based on Bluetooth device addresses and
not on RSSI.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controllers from Intel use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The wait_on_bit_timeout() is a simpler and race-free way of waiting for
a bit to be cleared than the current code in btusb.c. This patch updates
the code to use the helper function (its btusb copy - to be later
updated to use a global one).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The test for BTUSB_DOWNLOADING must be after adding to the wait queue
and setting the TASK_INTERRUPTIBLE state. Otherwise the flag may get
cleared after we test for it and we end up getting a timeout since
schedule_timeout() waits for the full duration. This patch uses a
wait_on_bit_timeout() + wake_up_bit(). To perform the task both
race-free as well as in a much simpler way.
Since there's no global wait_on_bit_timeout() helper yet (even though
all the building blocks for it are in place) this patch creates a
temporary local btusb copy of it until the global one has made it to
upstream trees.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In general all Intel Bluetooth devices support retrieving of additional
exception information. However for older generations including Wilkens
Peak and Stone Peak it is not as simple. So for now only enable the
Intel specific error handling for Snowfield Peak and later devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controllers from Atheros use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BugLink: https://bugs.launchpad.net/bugs/1400215
ath3k devices fail to load firmwares on xHCI buses, but work well on
EHCI, this might be a compatibility issue between xHCI and ath3k chips.
As my testing result, those chips will work on xHCI buses again with
this patch.
This workaround is from Qualcomm, they also did some workarounds in
Windows driver.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth HCI transport specification for USB device defines on how
a standard AMP controller is identified and operated. This patch adds
the needed handling to hook it up to the Bluetooth stack.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel Bluetooth devices use the generic USB device/interface class
descriptors that are assigned to Bluetooth H:2 conforming transports.
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
However newer chips have a bootloader stage and require firmware to
be loaded before they are functional. To avoid any confusion for the
users, just ignore unknown Intel Bluetooth devices.
All the released Intel Bluetooth devices have an entry in the device
table identifying their setup and support requirements. The advantage
here is that older kernel can be booted with newer devices without
causing any disturbance.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
New entries to the USB blacklist/quirk device table should be sorted
by USB vendor id. Fix the recent entry fro Marvell devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel Bluetooth controllers can provide an additional exception
info string when a hardware error event occurs. The core will now
call hdev->hw_error to let the driver read out this information.
This change will cause a reset of the hardware to bring it back
into functional state and then read the Intel exception info
string and print it along with the error information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb_disconnect() callback calls hci_unregister_dev() which in turn
calls btusb_close() if the HCI device is powered. The btusb_close()
function in turn will call btusb_free_frags(). It's therefore
unnecessary to have another call to btusb_free_frags() in the
btusb_disconnect() function. Besides the redundancy the second call
seems to also cause some strange stability issues which this patch then
also fixes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When loading the Intel firmware it can happen that the firmware loading
complete vendor event arrives before the command complete event for the
last firmware fragment.
< HCI Command: Vendor (0x3f|0x0009) plen 7
01 02 fc 03 00 00 00
> HCI Event: Vendor (0xff) plen 5
06 00 00 00 00
> HCI Event: Command Complete (0x0e) plen 4
Vendor (0x3f|0x0009) ncmd 31
Status: Success (0x00)
This is mainly caused by the fact that the vendor command and its
command complete event are transported over the bulk endpoints. The
firmware loading complete event however is send over the interrupt
endpoint. So with just bad timing one event arrives before the other.
Currently the code does not account for it. There are precautions for
receiving firmware loading complete event quickly, but not for receiving
it before the command complete.
Introduce an extra flag that tracks when the firmware sending has
completed from the driver point of view and track the completion of
the firmware loading procedure with a different flag. That way the
wakeup can be handled properly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some new upcoming drivers need to process HCI events or take extra
actions based on them before handing the event to the Bluetooth core
for processing. The new recv_event callback allows exactly such an
internal behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Sometimes suspend thread queues a command and wait for it's
response, meanwhile WLAN driver power cycles the card which
leads to crash. This patch makes sure that suspend thread is
woken up in remove path.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When driver is loaded, it is important to know if FW was already
active or it is freshly downloaded. This patch increases the
priority of the message.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag will be set in unload path to make sure that we skip
sending further commands, ignore interrupts and stop main thread
when unload starts.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If module init command fails, FW might not be in good state.
We will return from setup handler and skip downloading further
commands.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btmrvl_remove_card() calls kthread_stop() to stop the main thread,
but kthread_should_stop() is checked when all the activities are done
in the main thread before sleeping.
We will have kthread_should_stop() check as soon as main thread is
woken up. This fixes a crash issue caused due to an invalid memory
access while unnecessarily processing interrupts after card removal.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Silicon Wave based devices do support Inquiry Result with RSSI and
so let the core know to enable them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Roper Class 1 Bluetooth Dongle is another device that claims to
support Bluetooth 1.2 specification, but does not support the HCI
command for reading the local supported commands.
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 1.2 (0x2) HCI Revision: 0x0
LMP Version: 1.2 (0x2) LMP Subversion: 0x757
Manufacturer: Silicon Wave (11)
It clearly claims Bluetooth 1.2 support and in that regard has the
same issue as the AVM BlueFritz! USB devices (Silicon Wave based),
but the HCI Read Local Supported Commands command fails.
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Status (0x0f) plen 4
Read Local Supported Commands (0x04|0x0002) status 0x01 ncmd 1
Error: Unknown HCI Command
Use the HCI_QUIRK_BROKEN_LOCAL_COMMANDS quirk for these devices and
the failing command will be skipped.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The AVM BlueFritz! 2.0 USB dongles do not support the HCI command for
reading the local supported commands. So set this quirk to let the
core know about it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The AVM BlueFritz! 1.0 USB dongles do not support the HCI command for
reading the local supported commands. So set this quirk to let the
core know about it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Set hdev->set_bdaddr handler for ath3012. It sends the vendor specific HCI
command to change the public address. The change doesn't persist across
power cycle.
Signed-off-by: Toshi Kikuchi <toshik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This patch adds firmware dump support for marvell
bluetooth chipset. Currently only SD8897 is supported.
This is implemented based on dev_coredump, a new mechnism
introduced in kernel 3.18rc3
Firmware dump can be trigger by
echo 1 > /sys/kernel/debug/bluetooth/hci*/config/fw_dump
and when the dump operation is completed, data can be read by
cat /sys/class/devcoredump/devcd*/data
We have prepared following script to divide fw memory
dump data into multiple files based on memory type.
[root]# cat btmrvl_split_dump_data.sh
#!/bin/bash
# usage: ./btmrvl_split_dump_data.sh dump_data
fw_dump_data=$1
mem_type="ITCM DTCM SQRAM APU CIU ICU MAC EXT7 EXT8 EXT9 EXT10 EXT11 EXT12 EXT13 EXTLAST"
for name in ${mem_type[@]}
do
sed -n "/Start dump $name/,/End dump/p" $fw_dump_data > tmp.$name.log
if [ ! -s tmp.$name.log ]
then
rm -rf tmp.$name.log
else
# Remove the describle info "Start dump" and "End dump"
sed '1d' tmp.$name.log | sed '$d' > /data/$name.log
if [ -s /data/$name.log ]
then
echo "generate /data/$name.log"
else
sed '1d' tmp.$name.log | sed '$d' > /var/$name.log
echo "generate /var/$name.log"
fi
rm -rf tmp.$name.log
fi
done
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BT_INFO/BT_DBG etc. already takes care of adding a newline
An extra newline character inside message is removed in this
patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Host sleep status flag should be reset when there is an
interrupt from device.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This can be used to have GPIO host wakeup method suitable for the
platform and configurable GAP for host sleep handshake.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Calibration data can be downloaded through device tree method. This
patch adds the documentation. Also, instead of searching device tree
node by name using of_find_node_by_name() API, let's use
for_each_compatible_node().
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Correct the comments in this driver. Set the CRTSCTS flag means
automatic flow control is enabled.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some vendors require special handling of the rx data from the USB
bulk endpoints. For that case provide an internal callback that
can overwrite it with a custom receive function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controllers from Broadcom use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of having the driver generate the HCI Hardware Error event
manually, just call hci_reset_dev() to trigger the upper stack reset.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When constructing the event payload for the HCI_Hardware_Error event
message, use the HCI_EV_HARDWARE_ERROR define.
In addition rename the variables from hard_err to hw_err to clearly
indicate that this is about the hardware error and not a hard error.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
H5 Specification says:
If a SYNC message is received while in the Active State, it is
assumed that the peer device has reset. The local device should
therefore perform a full reset of the upper stack, and start Link
Establishment again at the Uninitialized State. Upon entering the
Active State, the first packet sent shall have its SEQ and ACK
numbers set to zero.
This patch resets the HCI H5 driver data/state to unitialized and
reports an HCI hardware error event to notify the upper stack that
HCI synchronization has been lost. H5 will be re-synchronized and
upper stack should generate an HCI Reset command.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull vfs updates from Al Viro:
"The big thing in this pile is Eric's unmount-on-rmdir series; we
finally have everything we need for that. The final piece of prereqs
is delayed mntput() - now filesystem shutdown always happens on
shallow stack.
Other than that, we have several new primitives for iov_iter (Matt
Wilcox, culled from his XIP-related series) pushing the conversion to
->read_iter()/ ->write_iter() a bit more, a bunch of fs/dcache.c
cleanups and fixes (including the external name refcounting, which
gives consistent behaviour of d_move() wrt procfs symlinks for long
and short names alike) and assorted cleanups and fixes all over the
place.
This is just the first pile; there's a lot of stuff from various
people that ought to go in this window. Starting with
unionmount/overlayfs mess... ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (60 commits)
fs/file_table.c: Update alloc_file() comment
vfs: Deduplicate code shared by xattr system calls operating on paths
reiserfs: remove pointless forward declaration of struct nameidata
don't need that forward declaration of struct nameidata in dcache.h anymore
take dname_external() into fs/dcache.c
let path_init() failures treated the same way as subsequent link_path_walk()
fix misuses of f_count() in ppp and netlink
ncpfs: use list_for_each_entry() for d_subdirs walk
vfs: move getname() from callers to do_mount()
gfs2_atomic_open(): skip lookups on hashed dentry
[infiniband] remove pointless assignments
gadgetfs: saner API for gadgetfs_create_file()
f_fs: saner API for ffs_sb_create_file()
jfs: don't hash direct inode
[s390] remove pointless assignment of ->f_op in vmlogrdr ->open()
ecryptfs: ->f_op is never NULL
android: ->f_op is never NULL
nouveau: __iomem misannotations
missing annotation in fs/file.c
fs: namespace: suppress 'may be used uninitialized' warnings
...
This patch adds driver support for marvell SD8887 chip.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Register offsets are different for SD8897 and newer chip SD8887.
We can not have common btmrvl_sdio_card_reg map for them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When receiving USB interrupt, bulk or isochronous packet, they normally
come in fragments. So far the driver just handed each fragment off to
the hci_recv_fragment function of the Bluetooth core. That function is
however so specific that is does not belong in the core. This patch
implements the same reassembly logic in the driver.
In addition this fixes a long standing bug where multiple complete
packets are received within a single USB packet.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The actual packet reassembly should be done inside the driver. To allow
this to happen cleanly in future patches, split the fragment reception
into its own functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb driver has been around for a while now and it is time to
bring its coding style in sync with what has been done for the
Bluetooth subsystem and other drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The complete TX URB handling is done via a switch statement in the
btusb_send_frame function. To allow for more clear separation between
control, bulk and isoc URBs, split them into allocation and submission.
Previously the inc_tx function has been used for tracking in-flight
URB for HCI commands and ACL data packets. Convert that into a common
function that either submits the URB or queues it when needed.
This provides the flexibility to allow vendor specific hdev->send_frame
callbacks without having to duplicate the whole URB handling logic.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All hdev->send() calls are these days done through a work queue. For the
btusb driver this means the btusb_send_frame() function. Because of this
we can safely use GFP_KERNEL for all memory allocations in this code
path.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Suspend could fail for some platforms because
btusb_suspend==> btusb_stop_traffic ==> usb_kill_anchored_urbs.
When btusb_bulk_complete returns before system suspend and resubmits
an URB, the system cannot enter suspend state.
Signed-off-by: Champion Chen <champion_chen@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
bt3c_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedefs for nsh_t and
dtl1_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case for dtl1_info_t
and a similar patch finds the nsh_t case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
btuart_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
bluecard_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In this expression: seq = (seq - 1) % 8
seq (u8) is implicitly converted to an int in the arithmetic operation.
So if seq value is 0, operation is ((0 - 1) % 8) => (-1 % 8) => -1.
The new seq value is 0xff which is an invalid ACK value, we expect 0x07.
It leads to frequent dropped ACK and retransmission.
Fix this by using '&' binary operator instead of '%'.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
btmrvl_add_card() function calls kthread_run that might return error
(e.g. if current thread is killed). If one tries to use the error
value as a pointer then invalid memory access oops happens.
Check kthread_run() return value, if it is an error then release resources
correctly.
TEST=boot computer with BT modules enabled. I see the error message that
BT device initialization failed. Now kernel does not crash. Hint: to enable
BT run 'rmmod btmrvl_sdio; modprobe btmrvl_sdio'
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ath3k driver is treating the version information badly when it
comes to loading the right firmware version and comparing that it
actually matches with the hardware.
Initially this showed up as this:
CHECK drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:373:17: warning: cast to restricted __le32
drivers/bluetooth/ath3k.c:435:17: warning: cast to restricted __le32
However when fixing this by actually using __packed and __le32 for
the ath3_version structure, more issues came up:
CHECK drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:381:32: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:381:32: expected restricted __le32 [usertype] rom_version
drivers/bluetooth/ath3k.c:381:32: got int [signed] <noident>
drivers/bluetooth/ath3k.c:382:34: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:382:34: expected restricted __le32 [usertype] build_version
drivers/bluetooth/ath3k.c:382:34: got int [signed] <noident>
drivers/bluetooth/ath3k.c:386:28: warning: restricted __le32 degrades to integer
drivers/bluetooth/ath3k.c:386:56: warning: restricted __le32 degrades to integer
This patch fixes every instance of the firmware version handling and
makes sure it is endian safe and uses proper unaligned access.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
.set_bdaddr handler is implemented for public address configuration.
A reboot restores the bdaddr to its original address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implemented .set_bdaddr handler provided by bluetooth stack for
Marvell devices for public address configuration.
A reboot restores the bdaddr to its original address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should suspend hci device and purge remaining data in tx queue
before enabling host sleep in firmware. If any data is sent to
firmware after host sleep is activated, firmware may end up
sending a TX_DONE interrupt to driver. If this interrupt gets
delivered to host while the SDIO host controller is suspending,
it may crash the system.
Conversely, in resume handler, we should resume hci device after
host sleep is de-activated.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The protocol for the UART might be configured, but that does not
mean the HCI device is registered. Return an error in that case
and only return the index number when HCI_UART_REGISTERED is set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The quirk for enabling external configuration with UART needs to be
provided via the HCI UART flags. Add a new flag for it and declare
it as valid.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing unknown or invalid flags to the HCI UART driver should
result in an error. So check which flags are valid and otherwise
return an error.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of setting data->isoc manually, use BTUSB_BROKEN_ISOC to
indicate that isochronous endpoints are not needed for CSR USB
sniffer devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The isochronous endpoints are not valid when the Intel Bluetooth
controller boots up in bootloader mode. So just mark these endpoints
as broken and then they will not be configured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The interrupt interface for the Intel USB bootloader devices is only
enabled after receiving SetInterface(0, AltSetting=0). When this USB
command is not send, then no HCI events will be received.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The module parameters to ignore devices based on USB VID/PID are not
needed at all. So just remove them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds support for configuring the hci_vhci virtual controllers
to require a setup stage using HCI_QUIRK_EXTERNAL_CONFIG. With this
option the virtual controller will start out as unconfigured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Broadcom USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Intel USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds support for configuring the hci_vhci virtual controllers
as a raw-only device using HCI_QUIRK_RAW_DEVICE. This is useful for
testing the kernel internal infrastructure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch fixes the following sparse warning caused by a missing
declaration in the header file:
drivers/bluetooth/btmrvl_main.c:218:5: warning: symbol 'btmrvl_pscan_window_reporting' was not declared. Should it be static?
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom BCM20702A0 USB controllers might come with the default
address 00:20:70:02:A0:00 when booting up. If this happens, then warn
about such address being used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Intel Bluetooth controllers come with a default address. If this
address is found, print an error to warn the user about it.
The controller is fully operational, but the danger of duplicate
Bluetooth addresses might causes issues. At least with a clear
error it becomes easier to debug these cases.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the Intel based USB devices add support for configuration of
the public device address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the Broadcom based USB devices add support for configuration of
the public device address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After BT_CMD_HOST_SLEEP_ENABLE command finishes, driver should
wait until getting BT_EVENT_HOST_SLEEP_ENABLE event to complete
suspend procedure.
Without this patch the suspend handler would return success
earlier. By the time when the BT_EVENT_HOST_SLEEP_ENABLE event
comes in the controller driver could have already turned off the
bus clock. This causes kernel crash or system reboot eventually.
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Jeff CF Chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A vendor specific command is sent to firmware during
initialization to enable this feature. This command is for
SD8897 only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
h5_reset_rx is unconditionally called at the end of
h5_complete_rx_pkt, no need to call it anymore after
that.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Invoking usb_sndbulkpipe() on same pipe for same purpose only once is
enough.
Signed-off-by: Adam Lee <adam8157@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When detecting a non-link packet, h5_reset_rx() frees the Rx skb.
Not returning after that will cause the upcoming h5_rx_payload()
call to dereference a now NULL Rx skb and trigger a kernel oops.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
This reverts commit ca58e594da.
For some unclear reason this patch tries to add suport for the
product ID 0xe005, but it ends up adding product ID 0x3005 to
all the tables. This is obviously wrong and causing multiple
issues.
The original patch seemed to be fine, but what ended up in 3.15
is not what the patch intended. The commit 0a3658cccd is
already present and adds support for this hardware. This means
only revert of this broken commit is requird.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Alexander Holler <holler@ahsoftware.de>
Cc: stable@vger.kernel.org # 3.15.x
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONXgoACgkQMUfUDdst+ymdSwCgwL0xmWjFYr/UbJ4LslOZ29Q4
BFQAoKyYe9LsfEyodBPabxJjKUtj1htz
=ZGSN
-----END PGP SIGNATURE-----
Merge tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into next
Pull tty/serial driver updates from Greg KH:
"Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while"
* tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
Revert "serial: imx: remove the DMA wait queue"
serial: kgdb_nmi: Improve console integration with KDB I/O
serial: kgdb_nmi: Switch from tasklets to real timers
serial: kgdb_nmi: Use container_of() to locate private data
serial: cpm_uart: No LF conversion in put_poll_char()
serial: sirf: Fix compilation failure
console: Remove superfluous readonly check
console: Use explicit pointer type for vc_uni_pagedir* fields
vgacon: Fix & cleanup refcounting
ARM: tty: Move HVC DCC assembly to arch/arm
tty/hvc/hvc_console: Fix wakeup of HVC thread on hvc_kick()
drivers/tty/n_hdlc.c: replace kmalloc/memset by kzalloc
vt: emulate 8- and 24-bit colour codes.
printk/of_serial: fix serial console cessation part way through boot.
serial: 8250_dma: check the result of TX buffer mapping
serial: uart: add hw flow control support configuration
tty/serial: at91: add interrupts for modem control lines
tty/serial: at91: use mctrl_gpio helpers
tty/serial: Add GPIOLIB helpers for controlling modem lines
ARM: at91: gpio: implement get_direction
...
Invoking usb_sndbulkpipe() on same pipe for same purpose only once is
enough.
Signed-off-by: Adam Lee <adam8157@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
After hardware reset, some BCM Bluetooth adapters obtain their initial firmware
from OTPROM chip. Once this initial firmware is running, the firmware can be
further upgraded over HCI interface with .hcd files provided by Broadcom. This
is also known as "patch RAM" support. This change implements that.
If the .hcd file is not found in /lib/firmware, BCM Bluetooth adapter continues
to operate with the initial firmware. Sample kernel log:
hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
Bluetooth: hci0: BCM: patch brcm/BCM20702A0-0a5c-22be.hcd not found
If the .hcd file is found, btusb driver pushes it to the BCM Bluetooth adapter and
it starts using the new firmware. Sample kernel log:
hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=1000 lmp_ver=06 lmp_subver=220e
Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=1389 lmp_ver=06 lmp_subver=220e
Above, we can see that hci_rev goes from 1000 to 1389 as a result of the upgrade.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit d2bee8fb6e.
Enabling autosuspend for Intel Bluetooth devices has been shown to not
work reliable. It does work for some people with certain combinations
of USB host controllers, but for others it puts the device to sleep and
it will not wake up for any event.
These events can be important ones like HCI Inquiry Complete or HCI
Connection Request. The events will arrive as soon as you poke the
device with a new command, but that is not something we can do in
these cases.
Initially there were patches to the xHCI USB controller that fixed
this for some people, but not for all. This could be well a problem
somewhere in the USB subsystem or in the USB host controllers or
just plain a hardware issue somewhere. At this moment we just do
not know and the only safe action is to revert this patch.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Tedd Ho-Jeong An <tedd.an@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
LDISCs shouldn't call tty->ops->write() from within
->write_wakeup().
->write_wakeup() is called with port lock taken and
IRQs disabled, tty->ops->write() will try to acquire
the same port lock and we will deadlock.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Andreas Bießmann <andreas@biessmann.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change subcmd parameter from int to u8 to match its use:
btmrvl_send_sync_cmd(priv, BT_CMD_MODULE_CFG_REQ, &subcmd, 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
For SD8897, CMD52 write_to_clear may have missing interrupts
under certain corner case condition. Use CMD53 read-to-clear
to fix the problem.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make sure no timer callback is running before releasing the
datastructure which contains it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If vendor specific HCI commands are received from application,
we should send corresponding events to stack.
These events should be consumed in driver, only if they are for
the internal HCI commands generated by driver.
This patch fixes the vendor command 0x3f stuck problem with
above mentioned change. For example,
hcitool cmd 3f 22 fe 06 22 21 20 43 50 00
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The version is always in little endian format. This patch makes the
driver work on both little and big endian CPUs.
Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove assignment in if-statements to be consistent with the coding
style.
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When stopping BCSP/H5, stop the retransmission timer before proceeding
to clean up packet queues. The previous code had a race condition where
the timer could trigger after the packet lists and protocol structure
had been removed which led to dereferencing NULL or use-after-free bugs.
Signed-off-by: Michael Knudsen <m.knudsen@samsung.com>
Reported-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This will help to manage table of supported IDs.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit bfacbb9 (Bluetooth: Use devname:vhci module alias for virtual HCI
driver) added the module alias to hci_vhci module so it's possible to
create the /dev/vhci node. However creating an alias without
specifying the minor doesn't allow us to create the node ahead,
triggerring module auto-load when it's first accessed.
Starting with depmod from kmod 16 we started to warn if there's a
devname alias without specifying the major and minor.
Let's do the same done for uhid, kvm, fuse and others, specifying a
fixed minor. In systems with systemd as the init the following will
happen: on early boot systemd will call "kmod static-nodes" to read
/lib/modules/$(uname -r)/modules.devname and then create the nodes. When
first accessed these "dead" nodes will trigger the module loading.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There exists a set of Bluetooth USB devices that show up on the USB
bus as 0a12:0001 and identify themselves as devices from CSR. However
they are not. When sending Read Local Version command they now have
a split personality and say they are from Broadcom.
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 2.0 (0x3) HCI Revision: 0x3000
LMP Version: 2.0 (0x3) LMP Subversion: 0x420b
Manufacturer: Broadcom Corporation (15)
The assumption is that they are neither CSR nor Broadcom based devices
and that they are designed and manufactured by someone else.
For the most parts they follow the Bluetooth HCI specification and
can be used as standard Bluetooth devices. However they have the
minor problem that the Delete Stored Link Key command is not working
as it should.
During the Bluetooth controller setup, this command is needed if
stored link keys are supported. For these devices it has to be
assumed that this is broken and so just set a quirk to clearly
indicate the behavior. After that the setup can just proceed.
Now the trick part is to detect these faulty devices since we do
not want to punish all CSR and all Broadcom devices. The original
devices do actually work according to the specification.
What is known so far is that these broken devices set the USB bcdDevice
revision information to 1.0 or less.
T: Bus=02 Lev=01 Prnt=01 Port=08 Cnt=03 Dev#= 9 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 1.00
S: Manufacturer=Bluetooth v2.0
S: Product=Bluetooth V2.0 Dongle
T: Bus=05 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 0.07
In case of CSR devices, the bcdDevice revision contains the firmware
build ID and that is normally a higher value. If the bcdDevice revision
is 1.0 or less, then an extra setup stage is checking if Read Local
Version returns CSR manufacturer information. If not then it will be
assumed that this is a broken device and the Delete Stored Link Key
command will be marked as broken.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The register for setting the SDIO card mode of a Type-B Bluetooth card
is called MD SET. The MD STAT register is used for reading the current
mode back.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth virtual HCI driver is using a misc character device to
allow emulation of HCI devices from userspace. This change enables the
support for vectored writes. Previously this was failing with EINVAL
since no complete H:4 packet was written.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Socket Bluetooth SDIO cards are branded versions of Toshiba SD-BT2
and they do not support sending HCI_Reset as first command. To make
this card work the HCI_QUIRK_RESET_ON_CLOSE quirk needs to be set
before registering the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch enables autosuspend for Intel Bluetooth device.
After btusb is loaded for Intel Bluetooth device, the power/control
attribute contains "on" value by default which disables the autosuspend.
Based on the USB PM document(Documentation/usb/power-management.txt),
kernel disabled the autosuspend for all devices other than hub by default.
"The USB specification states that all USB devices must support power
management. Nevertheless, the sad fact is that many devices do not
support it very well. You can suspend them all right, but when you
try to resume them they disconnect themselves from the USB bus or
they stop working entirely. This seems to be especially prevalent
among printers and scanners, but plenty of other types of device have
the same deficiency.
For this reason, by default the kernel disables autosuspend (the
power/control attribute is initialized to "on") for all devices other
than hubs. Hubs, at least, appear to be reasonably well-behaved in
this regard."
This document also described how the driver can enables the autosuspend
by using an USB api.
"Drivers can enable autosuspend for their devices by calling
usb_enable_autosuspend(struct usb_device *udev);
in their probe() routine, if they know that the device is capable of
suspending and resuming correctly. This is exactly equivalent to
writing "auto" to the device's power/control attribute."
For Intel Bluetooth device, the autosuspend needs to be enabled so the
device can transit to LPM(Low Power Mode) and ULPM(Ultra LPM) states after
receiving suspend message from the host.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device tree property can define the cal-data in proper order.
There is no need to swap the bytes in driver.
Also remove the redundant cal-data memory copy after removing the
byte swapping.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some ARM versions of Chromebook need to download a new calibration
data from host driver to firmware. They do have EEPROM but still
need a piece of new calibration data in test mode.
The cal-data is platform dependent. It's simpler and more feasible
to use device tree based cal-data instead of configuration file
based cal-data.
This patch remove configuration file based cal-data downloading
and replace it using cal-data from device tree.
When CONFIG_OF is not selected, or the specific property is not
present in the device tree, the calibration downloading will not
happen.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ath3k_table[] and ath3k_blist_tbl[] USB device tables can be
declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bpa10x_table[] device table can be declared as const
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bfusb_table[] device table can be declared as const
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb_table[] and blacklist_table[] USB device tables can be
declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of vhci_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of hci_uart_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of dtl1_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of btuart_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of btmrvl_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bt3c_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bluecard_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bfusb_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.
This patch also fixes up all drivers to provide the hdev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The function h4_check_data_len() is actually not used. So just
remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btmrvl_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The dtl1_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btuart_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt3c_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bluecard_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bfusb_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When changing the alternate setting for the ISOC endpoints, use the
hci_conn_num() helper function to count currently established SCO
and eSCO connections and store the the value. This avoids direct
access to the connection hash.
In addition use the stored value instead accessing the connection
hash over and over again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann