Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Associated pci_epf_bar structure is needed in pci_epc_clear_bar() to
clear a BAR correctly but it is reset in pci_epf_free_space() (that
is called first) which results in pci_epc_clear_bar() failure.
Reorder the pci_epc_clear_bar()/pci_epf_free_space() calls execution
to fix the issue.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
[lorenzo.pieralisi@arm.com: reworded the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Always skip odd BAR when skipping 64bit BARs in pci_epf_test_set_bar()
and pci_epf_test_alloc_space() otherwise pci_epf_test_set_bar() will
call pci_epc_set_bar() on an odd loop index when skipping reserved 64bit
BAR.
Moreover, pci_epf_test_alloc_space() will call pci_epf_alloc_space() on
bind for an odd loop index when BAR is 64bit but leaks on subsequent
unbind by not calling pci_epf_free_space().
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
PCI endpoint test function code should honor the .bar_fixed_size parameter
from underlying endpoint controller drivers or results may be unexpected.
In pci_epf_test_alloc_space(), check if BAR being used for test
register space is a fixed size BAR. If so, allocate the required fixed
size.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Set endpoint controller pointer to NULL in pci_epc_remove_epf()
to avoid -EBUSY on subsequent call to pci_epc_add_epf().
Add a check for NULL endpoint function pointer.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The address that is allocated using pci_epf_alloc_space() is
directly written to the target address of the Inbound Address
Translation unit (ie the HW component implementing inbound address
decoding) on endpoint controllers.
Designware IP [1] has a configuration parameter (CX_ATU_MIN_REGION_SIZE
[2]) which has 64KB as default value and the lower 16 bits of the Base,
Limit and Target registers of the Inbound ATU are fixed to zero. If the
programmed memory address is not aligned to 64 KB boundary this causes
memory corruption.
Modify pci_epf_alloc_space() API to take alignment size as argument in
order to allocate buffers to be mapped to BARs with an alignment that
suits the platform where they are used.
Add an 'align' parameter to epc_features which can be used by platform
drivers to specify the BAR allocation alignment requirements and use
this while invoking pci_epf_alloc_space().
[1] "I/O and MEM Match Modes" section in DesignWare Cores PCI Express
Controller Databook version 4.90a
[2] http://www.ti.com/lit/ug/spruid7c/spruid7c.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In case alloc_workqueue() fails, return -ENOMEM to avoid
potential NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
[lorenzo.pieralisi@arm.com: commit log and code update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use pci_epc_get_features() to get EPC features such as linkup
notifier support, MSI/MSIX capable, BAR configuration etc and use it
for configuring pci-epf-test. Since these features are now obtained
directly from EPC driver, remove pci_epf_test_data which was initially
added to have EPC features in endpoint function driver.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
It's useless to allocate memory for next BAR if the current BAR is a
64Bit BAR. Stop allocating memory for the next BAR, if the current
BARs flag indicates this is a 64Bit BAR.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Now that pci_epf_alloc_space() sets BAR MEM TYPE flags as 64Bit or
32Bit based on size, remove setting it in function driver.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pci_epf_alloc_space() sets the MEM TYPE flags to indicate a 32-bit
Base Address Register irrespective of the size. Fix it here to indicate
64-bit BAR if the size is > 2GB.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add a helper function pci_epc_get_first_free_bar() to get the first
unreserved BAR that can be used for endpoint function.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add a new pci_epc_ops ->get_features() to get the features
supported by the EPC. Since EPC can provide different features to
different functions, the ->get_features() ops takes _func_no_ as
an argument.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Functions copying from/to IO addresses should use the
memcpy_fromio()/memcpy_toio() API rather than plain memcpy().
Fix the issue detected through the sparse tool.
Fixes: 349e7a85b2 ("PCI: endpoint: functions: Add an EP function to test PCI")
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
[lorenzo.pieralisi@arm.com: updated log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
CC: Niklas Cassel <niklas.cassel@axis.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
CC: linux-pci@vger.kernel.org
CC: linux-kernel@vger.kernel.org
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add pci_epc_set_msi() maximum 32 interrupts validation.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add MSI-X support and update driver documentation accordingly.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cleanup PCI_ENDPOINT_TEST memspace (by moving the interrupt number away
from command section).
Add IRQ_TYPE register to identify the triggered ID interrupt required
for the READ/WRITE/COPY tests and raise IRQ test commands.
Update documentation accordingly.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Change {cdns, dra7xx, artpec6, dw, rockchip}_pcie_ep_raise_irq() and
pci_epc_raise_irq() signature, namely the interrupt_num variable type
from u8 to u16 to accommodate 2048 maximum MSI-X interrupts.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Alan Douglas <adouglas@cadence.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
commit ef1433f717 ("PCI: endpoint: Create configfs entry for each
pci_epf_device_id table entry") while adding configfs entry for each
pci_epf_device_id table entry introduced a NULL pointer dereference error
when CONFIG_PCI_ENDPOINT_CONFIGFS is not enabled.
Fix it here.
Fixes: ef1433f717 ("PCI: endpoint: Create configfs entry for each
pci_epf_device_id table entry")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to use list_for_each_entry_safe() because the
pci_ep_cfs_remove_epf_group() function frees "group".
Fixes: ef1433f717 ("PCI: endpoint: Create configfs entry for each pci_epf_device_id table entry")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
- use usleep() instead of mdelay() in endpoint test (Jia-Ju Bai)
- add configfs entries for pci_epf_driver device IDs (Kishon Vijay
Abraham I)
- clean up pci_endpoint_test driver (Gustavo Pimentel)
* lorenzo/pci/endpoint:
PCI: endpoint: Create configfs entry for each pci_epf_device_id table entry
misc: pci_endpoint_test: Use pci_irq_vector function
PCI: endpoint: functions/pci-epf-test: Replace lower into upper case characters
misc: pci_endpoint_test: Replace lower into upper case characters
PCI: endpoint: Replace mdelay with usleep_range() in pci_epf_test_write()
In order to be able to provide correct driver_data for pci_epf device,
a separate configfs entry for each pci_epf_device_id table entry in
pci_epf_driver is required.
Add support to create configfs entry for each pci_epf_device_id
table entry here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The PCIe controller dual mode is capable of operating in Root Complex
(RC) mode as well as EP mode by configuration option.
Add EP support to the DesignWare driver on top of RC mode support.
Add new property on pci_epc structure which allow to configure
pci_epf_test driver accordingly to the controller specific requirements.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Replace all initial lower case character into upper case in comments
and debug printks.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pci_epf_test_write() is never called in atomic context.
The call chain ending up at pci_epf_test_write() is:
[1] pci_epf_test_write() <- pci_epf_test_cmd_handler()
pci_epf_test_cmd_handler() is set as a parameter of INIT_DELAYED_WORK()
in pci_epf_test_probe().
This function is not called in atomic context.
Despite never getting called from atomic context, pci_epf_test_write()
calls mdelay() to busy wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Since a 64-bit BAR consists of a BAR pair, and since there is no
BAR after BAR_5, BAR_5 cannot be 64-bits wide.
This sanity check is done in pci_epc_clear_bar(), so that we don't need
to do this sanity check in all epc->ops->clear_bar() implementations.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar.
This is needed so that epc->ops->clear_bar() can clear the BAR pair,
if the BAR is 64-bits wide.
This also makes it possible for pci_epc_clear_bar() to sanity check
the flags.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
If a 64-bit BAR was set-up, we need to skip a BAR,
since a 64-bit BAR consists of a BAR pair.
We need to check what BAR width the epc->ops->set_bar() specific
implementation actually did set-up, since some drivers, like the
Cadence EP controller, sometimes sets up a 64-bit BAR, even though
a 32-bit BAR was requested.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Setting a BAR size > 4 GB is invalid if PCI_BASE_ADDRESS_MEM_TYPE_64
flag is not set.
This sanity check is done in pci_epc_set_bar(), so that we don't need
to do this sanity check in all epc->ops->set_bar() implementations.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
If flag PCI_BASE_ADDRESS_SPACE_IO is set, also having any
PCI_BASE_ADDRESS_MEM_* bit set is invalid.
This sanity check is done in pci_epc_set_bar(), so that we don't need
to do this sanity check in all epc->ops->set_bar() implementations.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Since a 64-bit BAR consists of a BAR pair, and since there is no
BAR after BAR_5, BAR_5 cannot be 64-bits wide.
This sanity check is done in pci_epc_set_bar(), so that we don't need
to do this sanity check in all epc->ops->set_bar() implementations.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add barno and flags to struct epf_bar.
That way we can simplify epc->ops->set_bar()/pci_epc_set_bar()
by passing a struct *epf_bar instead of a whole lot of arguments.
This is needed so that epc->ops->set_bar() implementations can
modify BAR flags. Will be utilized in a succeeding patch.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
If a BAR supports 64-bit width or not depends on the hardware,
and should thus not depend on sizeof(dma_addr_t).
If a certain hardware doesn't support 64-bit BARs, its
epc->ops->set_bar() implementation should return -EINVAL
when PCI_BASE_ADDRESS_MEM_TYPE_64 is set.
We can't change pci_epc_set_bar() to only set
PCI_BASE_ADDRESS_MEM_TYPE_64 based on size, since if the user,
for some reason, wants to configure a BAR with a 64-bit width,
even though the BAR size is less than 4 GB, he should be able
to do that.
However, since pci-epf-test is simply a test and not an API,
we can set PCI_BASE_ADDRESS_MEM_TYPE_64 in pci-epf-test itself
only based on size.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Remove the pci_epf_create() goto labels completely and handle the
errors at the respective call site to simplify the function error
handling.
Signed-off-by: Rolf Evers-Fischer <rolf.evers.fischer@aptiv.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
'put_device()' calls the relase function 'pci_epf_dev_release()',
which already frees 'epf->name' and 'epf'.
Therefore we must not free them again after 'put_device()'.
Fixes: 5e8cb40338 ("PCI: endpoint: Add EP core layer to enable EP controller and EP functions")
Signed-off-by: Rolf Evers-Fischer <rolf.evers.fischer@aptiv.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This commit replaces allocating and freeing the intermediate
'buf'/'func_name' with a combination of 'kstrndup()' and 'len'.
'len' is the required length of 'epf->name'.
'epf->name' should be either the first part of 'name' preceding the '.'
or the complete 'name', if there is no '.' in the name.
Signed-off-by: Rolf Evers-Fischer <rolf.evers.fischer@aptiv.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
* pci/spdx:
PCI: Add SPDX GPL-2.0+ to replace implicit GPL v2 or later statement
PCI: Add SPDX GPL-2.0+ to replace GPL v2 or later boilerplate
PCI: Add SPDX GPL-2.0 to replace COPYING boilerplate
PCI: Add SPDX GPL-2.0 to replace GPL v2 boilerplate
PCI: Add SPDX GPL-2.0 when no license was specified
Fix the pci_epf_make() function so it can now bind many EPF devices to the
same EPF driver.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This patch updates the prototype of most handlers from 'struct
pci_epc_ops' so the EPC library can now support multi-function devices.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add SPDX GPL-2.0 to all PCI files that specified the GPL version 2 license.
Remove the boilerplate GPL version 2 language, relying on the assertion in
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") that the SPDX identifier may be used instead of the
full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") added SPDX GPL-2.0 to several PCI files that
previously contained no license information.
Add SPDX GPL-2.0 to all other PCI files that did not contain any license
information and hence were under the default GPL version 2 license of the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 7232888366 ("of: restrict DMA configuration"),
of_dma_configure() doesn't configure the coherent_dma_mask/dma_mask
of endpoint function device (since it doesn't have a DT node associated
with and hence no dma-ranges property), resulting in
dma_alloc_coherent() (used in pci_epf_alloc_space()) to fail.
Fix it by making dma_alloc_coherent() use EPC's device for allocating
memory address.
Link: http://lkml.kernel.org/r/64d63468-d28f-8fcd-a6f3-cf2a6401c8cb@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: tweaked commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Tested-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
find_first_zero_bit()'s parameter 'size' is defined in bits,
not in bytes.
Calling find_first_zero_bit() with the wrong size unit
will lead to insidious bugs.
Fix this by calling find_first_zero_bit() with size BITS_PER_LONG,
rather than sizeof() and add missing find_first_zero_bit() return
handling.
Fixes: d746799116 ("PCI: endpoint: Introduce configfs entry for configuring EP functions")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
func_no is a member of struct pci_epf.
Since struct pci_epf is used as an argument to pci_epc_add_epf() (to
bind an endpoint function to a controller), struct pci_epf.func_no
should be populated before calling pci_epc_add_epf().
Initialize the struct pci_epf.func_no member before calling
pci_epc_add_epf(), to fix the endpoint function binding to
an endpoint controller.
Fixes: d746799116 ("PCI: endpoint: Introduce configfs entry for configuring EP functions")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Jianping Liu