Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[Nick Dyer: reworked to move free of input device into separate function
and only call in paths that require it.]
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the case where the CHG/interrupt line mode is not configured correctly,
this warning is output to dmesg output for each interrupt. Downgrade the
message to debug.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This should fix the following issues reported by Coverity:
*** CID 1230625: Logically dead code (DEADCODE)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1692 in mxt_initialize()
*** CID 1230627: Missing break in switch (MISSING_BREAK)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1436 in mxt_get_object_table()
*** CID 1230629: Out-of-bounds write (OVERRUN)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1267 in mxt_update_cfg()
*** CID 1230632: Unused pointer value (UNUSED_VALUE)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1211 in mxt_update_cfg()
Acked-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's split config update code a bit so it is hopefully a bit easier to
read. Also, the firmware update callback should be the entity releasing
firmware blob, not lower layers.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
I think having control flow with 2 goto/labels/flags is quite hard to read,
this version is a bit more readable IMO.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
By writing zero to both the active and idle cycle times the maXTouch device
is put into a deep sleep mode when it consumes minimal power. It is
unnecessary to change the configuration of any other objects (for example
to disable T9 touchscreen).
It is counterproductive to reset the chip on resume, it will result in a
long delay. However it is necessary to issue a calibrate command after the
chip has spent any time in deep sleep.
This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
maXTouch chips allow the reading of multiple messages in a single I2C
transaction, which reduces bus overhead and improves performance/latency. The
number of messages available to be read is given by the value in the T44
object which is located directly before the T5 object.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is in preparation for support of the T44 message count object.
Also, cache T5 address to avoid lookup on every interrupt cycle.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By storing the previous T6 status byte multiple debug output of the same
status can be suppressed (for example CFGERR).
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The T5 object may have various sizes depending on the objects used on the
particular maXTouch chip and firmware version, therefore it can't be
hardcoded in the driver. Allocate a buffer on probe instead.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MXT device may be in bootloader mode on probe, due to:
1) APP CRC failure, either:
a) flash corruption
b) bad power or other intermittent problem while checking CRC
2) If the device has been reset 10 or more times without accessing comms
3) Warm probe, device was in bootloader mode already
This code attempts to recover from 1(b) and 3.
There is an additional complexity: we have to try two possible bootloader
addresses because the mapping is not one-to-one and we don't know the exact
model yet.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Later chips (for example mXT1664S) different mappings for bootloader
addresses. This means that we must look at the family ID to determine
which address to use.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On a warm probe, the device might be in a state where an flash operation was
not completed.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the bootloader on the touchscreen controller fails to initialise the
firmware image, it stays in bootloader mode and reports a failure. It is
possible to reflash a working firmware image from this state.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By validating the checksum, we can identify if the configuration is
corrupt. In addition, this patch writes the configuration in a short
series of block writes rather than as many individual values.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The existing implementation which encodes the configuration as a binary
blob in platform data is unsatisfactory since it requires a kernel
recompile for the configuration to be changed, and it doesn't deal well
with firmware changes that move values around on the chip.
Atmel define an ASCII format for the configuration which can be exported
from their tools. This patch implements a parser for that format which
loads the configuration via the firmware loader and sends it to the MXT
chip.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Touchpads are pointers, so make sure to pass the correct values to
input_mt_report_pointer_emulation(). Without this, tap-to-click doesn't
work.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is useful to initialise the input device later:
- Screen parameters may not be not known yet, for instance if waiting for
firmware loader to return.
- Device may be in bootloader mode on probe (but could still be recovered by
firmware download).
In addition, later devices have a different touchscreen object (T100) which
requires handling differently.
This also reduces the complexity of the probe function.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The maXTouch chips use the CHG line to generate status events in bootloader
mode, and during configuration download, before there is enough information
to configure the input device. Therefore set up the interrupt handler
earlier.
However, this introduces states where parts of the interrupt processing
must not run. Use data->object_table as a way to tell whether the chip
information is valid, and data->input_dev as a way to tell whether it is
valid to generate input report.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By reading the touchscreen configuration from the settings that the
maXTouch chip is actually using, we can remove some platform data.
The matrix size is not used for anything, and results in some rather
confusing code to re-read it because it may change when configuration
is downloaded, so don't print it out.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Atmel supplies firmware files in ASCII HEX format (.enc) which must be
converted before they can be loaded by kernel driver. Try to detect
the error and print a friendly error message rather than feeding junk
to the bootloader.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By implementing a frame counter, print out fewer debug messages (the
firmware may contain hundreds of frames).
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move bootloaders reads/writes into separate functions. Instead of switching
client->addr, define new field bootloader_addr in mxt_data. Implement
lookup calculation for bootloader addresses.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The configuration is stored in NVRAM on the maXTouch chip. When the device
is reset it reports a CRC of the stored configuration values. Therefore it
isn't necessary to send the configuration on each probe - we can check the
CRC matches and avoid a timeconsuming backup/reset cycle.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The delay before the chip can be accessed after reset varies between
different chips in maXTouch family. Waiting for an interrupt and a T6
status message with the RESET bit set is a better behaviour.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rather than msleep for MXT_RESET_TIME and MXT_FWRESET_TIME during the
transition to bootloader mode and the transition back from app, wait for
the CHG assert to indicate that the transition is done.
This change replaces the msleep with a wait for completion that the
mxt_interrupt handler signals.
Also add CHG poll after last firmware frame - some bootloader versions will
assert the interrupt line after the final frame, in testing this meant that
the driver attempts to read the info block too early whilst the chip is
still resetting.
This improves firmware update time as we no longer wait longer than
necessary for each reset.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver should not immediately read bootloader status when in
Application Update Mode. The CHG line will assert when the device has made
a state transition and is ready to report a new status via i2c.
This change adds a wait for completion in mxt_check_bootloader, and changes
the mxt_interrupt handler to signal the completion.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These two object table entry fields are reported 1 less than their value.
When used, however, we always want the actual size and instances.
To keep the object size and instances 1-byte fields, and thus preserve
the object-table struct's 6-byte packed alignment, add some convenient
accessor functions that do the +1 every time these fields are accessed.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* The mapping of the GPIO numbers into the T19 status byte varies between
different maXTouch chips. Some have up to 7 GPIOs. Allowing a keycode array
of up to 8 items is simpler and more generic. So replace #define with
configurable number of keys which also allows the removal of is_tp.
* Rename platform data parameters to include "t19" to prevent confusion with
T15 key array.
* Probe aborts early on when pdata is NULL, so no need to check.
* Move "int i" to beginning of function (mixed declarations and code)
* Use API calls rather than __set_bit()
* Remove unused dev variable.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is not necessary to download these values to the maXTouch chip on every
probe, since they are stored in NVRAM. It makes life difficult when tuning
the device to keep them in sync with the config array/file, and requires a
new kernel build for minor tweaks.
These parameters only represent a tiny subset of the available
configuration options, tracking all of these options in platform data would
be a endless task. In addition, different versions of maXTouch chips may
have these values in different places or may not even have them at all.
Having these values also makes life more complex for device tree and other
platforms where having to define a static configuration isn't helpful.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the wrapper function for retrieving the platform data instead
of accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is a more complete atmel patch-series out by Nick Dyer that fixes
this and other things, but in the meantime this is the minimal thing to
get the touchscreen going on (at least my) Pixel Chromebook.
Not that I want my dirty fingers near that beautiful screen, but it
seems that a non-initialized touchscreen will also end up being a
constant wakeup source, so you have to disable it to go to sleep. And
it's easier to just fix the initialization sequence.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This same driver can be used by atmel based touchscreens and touchpads
(buttonpads). Platform data may specify a device is a touchpad
using the is_tp flag.
This will cause the driver to perform some touchpad specific
initializations, such as:
* register input device name "Atmel maXTouch Touchpad" instead of
Touchscreen.
* register BTN_LEFT & BTN_TOOL_* event types.
* register axis resolution (as a fixed constant, for now)
* register BUTTONPAD property
* process GPIO buttons using reportid T19
Input event GPIO mapping is done by the platform data key_map array.
key_map[x] should contain the KEY or BTN code to send when processing
GPIOx from T19. To specify a GPIO as not an input source, populate
with KEY_RESERVED, or 0.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use %*ph format specifier to print small buffer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds