Pointer variables of void * type do not require type cast.
Signed-off-by: wuych <yunchuan@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently parse the SFP EEPROM to a bitmap of ethtool link modes,
and then attempt to convert the link modes to a PHY interface mode.
While this works at present, there are cases where this is sub-optimal.
For example, where a module can operate with several different PHY
interface modes.
To start addressing this, arrange for the SFP EEPROM parsing to also
provide a bitmap of the possible PHY interface modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
phydev->port was not set and always reported as PORT_TP.
Set phydev->port according to inserted SFP module.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no real need for disabling autonigotiation in config_init().
Leave it enabled by default.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting 10G without autonegotiation is invalid according to
phy_ethtool_ksettings_set(). Thus, we need to set it during
autonegotiation.
If 1G autonegotiation can't complete for quite a time, but there is
signal in line, switch line interface type to 10GBase-R, if supported,
in hope for link to be established.
And vice versa. If 10GBase-R link can't be established for quite a time,
and autonegotiation is enabled, and there is signal in line, switch line
interface type to appropriate 1G mode, i.e. 1000Base-X or SGMII, if
supported.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
No functional changes, just move read link status routines below
autonegotiation configuration to make future functional changes more
distinct.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFP modules uses RX_LOS for link indication. In such cases link
will be always up, even without cable connected. RX_LOS changes will
trigger link_up()/link_down() upstream operations. Thus, check that SFP
link is operational before actual read link status.
If there is no SFP cage connected to the tranciever, check only PMD
Recieve Signal Detect register.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for the Marvell 88X2222 multi-speed ethernet
transceiver.
This PHY provides data transmission over fiber-optic as well as Twinax
copper links. The 88X2222 supports 2 ports of 10GBase-R and 1000Base-X
on the line-side interface. The host-side interface supports 4 ports of
10GBase-R, RXAUI, 1000Base-X and 2 ports of XAUI.
This driver, however, supports only XAUI on the host-side and
1000Base-X/10GBase-R on the line-side, for now. The SGMII is also
supported over 1000Base-X. Interrupts are not supported.
Internal registers access compliant with the Clause 45 specification.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
wuych