In their RZN1 SoC, Renesas put a CAN controller supposed to act very
similarly to the original Philips sja1000. In practice, while flooding
the bus with another device, we discovered that the controller very
often after an overrun situation would just refuse any new frame, drop
them all and trigger over and over again the overrun interrupt, even
though the buffer would have been totally emptied. The controller acts
like if its internal buffer offsets (where it writes and where the host
reads) where totally screwed-up.
Renesas manual mentions a single action to perform in order to
resynchronize the read and write offsets within the buffer: performing
a soft reset.
Performing a soft reset takes a bit of time and involves small delays,
so better do that in a threaded handler rather than inside the hard IRQ
handler.
Add platform data to recognize the platforms which need this workaround,
and when the faulty situation is diagnosed, stop what is being
performed and request the threaded handler to be executed in order to
perform the reset.
Tested-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com> # 5.10
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20230616134553.2786391-2-miquel.raynal@bootlin.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to support a flavor of the sja1000 which sometimes freezes, it
will be needed upon certain interrupts to perform a soft reset. The soft
reset operation takes a bit of time, so better not do it within the hard
interrupt handler but rather in a threaded handler. Let's prepare the
possibility for sja1000_err() to request "interrupting" the current flow
and request the threaded handler to be run while keeping the interrupt
line low.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20230616134553.2786391-1-miquel.raynal@bootlin.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The reset line from the Asix chip to the SJA1000 is asserted after boot up
until it is deasserted by a register write
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Link: https://lore.kernel.org/all/20230120112616.6071-8-uttenthaler@ems-wuensche.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the missing free_sja1000dev() before return from
sja1000_isa_probe() in the register_sja1000dev() error handling case.
In addition, remove blanks before goto labels.
Fixes: 2a6ba39ad6 ("can: sja1000: legacy SJA1000 ISA bus driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/all/1668168521-5540-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit a6d190f8c7 ("can: skb: drop tx skb if in listen only
mode") the priv->ctrlmode element is read even on virtual CAN
interfaces that do not create the struct can_priv at startup. This
out-of-bounds read may lead to CAN frame drops for virtual CAN
interfaces like vcan and vxcan.
This patch mainly reverts the original commit and adds a new helper
for CAN interface drivers that provide the required information in
struct can_priv.
Fixes: a6d190f8c7 ("can: skb: drop tx skb if in listen only mode")
Reported-by: Dariusz Stojaczyk <Dariusz.Stojaczyk@opensynergy.com>
Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: Max Staudt <max@enpas.org>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221102095431.36831-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org # 6.0.x
[mkl: patch pch_can, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Return value directly from register_candev() instead of
getting value from redundant variable ret.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Jinpeng Cui <cui.jinpeng2@zte.com.cn>
Link: https://lore.kernel.org/all/20220831161835.306079-1-cui.jinpeng2@zte.com.cn
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The SJA1000 CAN controller on RZ/N1 SoC has no clock divider register
(CDR) support compared to others.
This patch adds support for RZ/N1 SJA1000 CAN Controller, by adding
SoC specific compatible to handle this difference as well as using
clk framework to retrieve the CAN clock frequency.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20220710115248.190280-7-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently, some CAN drivers support hardware timestamping, some do
not. But userland has no method to query which features are supported
(aside maybe of getting RX messages and observe whether or not
hardware timestamps stay at zero).
The canonical way for a network driver to advertised what kind of
timestamping it supports is to implement ethtool_ops::get_ts_info().
This patch only targets the CAN drivers which *do not* support
hardware timestamping. For each of those CAN drivers, implement the
get_ts_info() using the generic ethtool_op_get_ts_info().
This way, userland can do:
| $ ethtool --show-time-stamping canX
to confirm the device timestamping capacities.
N.B. the drivers which support hardware timestamping will be migrated
in separate patches.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220727101641.198847-6-mailhol.vincent@wanadoo.fr
[mkl: mscan: add missing mscan_ethtool_ops]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a dedicated flag in uapi/linux/can/error.h to notify the userland
that fields data[6] and data[7] of the CAN error frame were
respectively populated with the tx and rx error counters.
For all driver tree-wide, set up this flags whenever needed.
Link: https://lore.kernel.org/all/20220719143550.3681-12-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 215db1856e ("can: sja1000: Consolidate and unify state change handling")
Link: https://lore.kernel.org/all/20220719143550.3681-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As per Chapter 6.5.16 of the RZ/N1 Peripheral Manual, The SJA1000
CAN controller does not support Clock Divider Register compared to
the reference Philips SJA1000 device.
This patch adds a device quirk to handle this difference.
Link: https://lore.kernel.org/all/20220710115248.190280-4-biju.das.jz@bp.renesas.com
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 30f3b42147 ("can: mark led trigger as broken") the
CAN specific LED support was disabled and marked as BROKEN. As the
common LED support with CONFIG_LEDS_TRIGGER_NETDEV should do this work
now the code can be removed as preparation for a CAN netdevice Kconfig
rework.
Link: https://lore.kernel.org/all/20220518154527.29046-1-socketcan@hartkopp.net
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
[mkl: remove led.h from MAINTAINERS]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Technologic Systems has rebranded as embeddedTS with the current
domain eventually going offline. Update web/doc URLs to correct
resource locations.
Link: https://lore.kernel.org/all/20220329201229.16279-1-kris@embeddedTS.com
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::tx_bytes should not be increased when
sending RTR frames.
The function can_get_echo_skb() already returns the correct length,
even for RTR frames (c.f. [1]). However, for historical reasons, the
drivers do not use can_get_echo_skb()'s return value and instead, most
of them store a temporary length (or dlc) in some local structure or
array. Using the return value of can_get_echo_skb() solves the
issue. After doing this, such length/dlc fields become unused and so
this patch does the adequate cleaning when needed.
This patch fixes all the CAN drivers.
Finally, can_get_echo_skb() is decorated with the __must_check
attribute in order to force future drivers to correctly use its return
value (else the compiler would emit a warning).
[1] commit ed3320cec2 ("can: dev: __can_get_echo_skb():
fix real payload length return value for RTR frames")
Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
[mkl: add conversion for grcan]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::rx_bytes should not be increased for the
RTR frames.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the rx_packets and
rx_bytes fields of struct net_device_stats because no actual payload
were transmitted on the wire.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-2-mailhol.vincent@wanadoo.fr
CC: Marc Kleine-Budde <mkl@pengutronix.de>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Ludovic Desroches <ludovic.desroches@microchip.com>
CC: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
CC: Maxime Ripard <mripard@kernel.org>
CC: Chen-Yu Tsai <wens@csie.org>
CC: Jernej Skrabec <jernej.skrabec@gmail.com>
CC: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
CC: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the last channel is not available then "dev" is freed. Fortunately,
we can just use "pdev->irq" instead.
Also we should check if at least one channel was set up.
Fixes: fd734c6f25 ("can/sja1000: add driver for EMS PCMCIA card")
Link: https://lore.kernel.org/all/20211124145041.GB13656@kili
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds name and (possibly) firmware version information to
the kernel about the detected PEAK-System CAN - PCI/PCIe interface
card.
Link: https://lore.kernel.org/r/20210607151720.13571-1-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: reformated struct pci_device_id peak_pci_tbl]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to implement byte queue limits (bql) in CAN drivers, the
length of the CAN frame needs to be passed into the networking stack
even if the transmission failed for some reason.
To avoid to calculate this length twice, extend can_free_echo_skb() to
return that value. Convert all users of this function, too.
This patch is the natural extension of commit:
| 9420e1d495 ("can: dev: can_get_echo_skb(): extend to return can
| frame length")
Link: https://lore.kernel.org/r/20210319142700.305648-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A relatively calm release at this time, and no massive code changes
are found in the stats, while a wide range of code refactoring and
cleanup have been done.
Note that this update includes the tree-wide trivial changes for
dropping the return value from ISA remove callbacks, too.
Below lists up some highlight:
* ALSA Core:
- Support for the software jack injection via debugfs
- Fixes for sync_stop PCM operations
* HD-audio and USB-audio:
- A few usual HD-audio device quirks
- Updates for Tegra HD-audio
- More quirks for Pioneer and other USB-audio devices
- Stricter state checks at USB-audio disconnection
* ASoC:
- Continued code refactoring, cleanup and fixes in ASoC core API
- A KUnit testsuite for the topology code
- Lots of ASoC Intel driver Realtek codec updates, quirk additions and
fixes
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers
* Others:
- Drop return value from ISA driver remove callback
- Cleanup with DIV_ROUND_UP() macro
- FireWire updates, HDSP output loopback support
-----BEGIN PGP SIGNATURE-----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=QgvS
-----END PGP SIGNATURE-----
Merge tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"A relatively calm release at this time, and no massive code changes
are found in the stats, while a wide range of code refactoring and
cleanup have been done.
Note that this update includes the tree-wide trivial changes for
dropping the return value from ISA remove callbacks, too.
Below lists up some highlight:
ALSA Core:
- Support for the software jack injection via debugfs
- Fixes for sync_stop PCM operations
HD-audio and USB-audio:
- A few usual HD-audio device quirks
- Updates for Tegra HD-audio
- More quirks for Pioneer and other USB-audio devices
- Stricter state checks at USB-audio disconnection
ASoC:
- Continued code refactoring, cleanup and fixes in ASoC core API
- A KUnit testsuite for the topology code
- Lots of ASoC Intel driver Realtek codec updates, quirk additions
and fixes
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers
Others:
- Drop return value from ISA driver remove callback
- Cleanup with DIV_ROUND_UP() macro
- FireWire updates, HDSP output loopback support"
* tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (322 commits)
ALSA: hda: intel-dsp-config: add Alder Lake support
ASoC: soc-pcm: fix hw param limits calculation for multi-DAI
ASoC: Intel: bytcr_rt5640: Add quirk for the Acer One S1002 tablet
ASoC: Intel: bytcr_rt5651: Add quirk for the Jumper EZpad 7 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Voyo Winpad A15 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Estar Beauty HD MID 7316R tablet
ASoC: soc-pcm: fix hwparams min/max init for dpcm
ALSA: hda/realtek: Quirk for HP Spectre x360 14 amp setup
ALSA: usb-audio: Add implicit fb quirk for BOSS GP-10
ALSA: hda: Add another CometLake-H PCI ID
ASoC: soc-pcm: add soc_pcm_hw_update_format()
ASoC: soc-pcm: add soc_pcm_hw_update_chan()
ASoC: soc-pcm: add soc_pcm_hw_update_rate()
ASoC: wm_adsp: Remove unused control callback structure
ASoC: SOF: relax ABI checks and avoid unnecessary warnings
ASoC: codecs: lpass-tx-macro: add dapm widgets and route
ASoC: codecs: lpass-tx-macro: add support for lpass tx macro
ASoC: qcom: dt-bindings: add bindings for lpass tx macro codec
ASoC: codecs: lpass-rx-macro: add iir widgets
ASoC: codecs: lpass-rx-macro: add dapm widgets and route
...
The driver core ignores the return value of the remove callback, so
don't give isa drivers the chance to provide a value.
Adapt all isa_drivers with a remove callbacks accordingly; they all
return 0 unconditionally anyhow.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/net/can/sja1000/tscan1.c
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for drivers/i2c/
Reviewed-by: Takashi Iway <tiwai@suse.de> # for sound/
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for drivers/media/
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210122092449.426097-4-uwe@kleine-koenig.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to implement byte queue limits (bql) in CAN drivers, the length of the
CAN frame needs to be passed into the networking stack after queueing and after
transmission completion.
To avoid to calculate this length twice, extend can_get_echo_skb() to return
that value. Convert all users of this function, too.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-14-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a frame_len argument to can_put_echo_skb() which is used to save length of
the CAN frame into field frame_len of struct can_skb_priv so that it can be
later used after transmission completion. Convert all users of this function,
too.
Drivers which implement BQL call can_put_echo_skb() with the output of
can_skb_get_frame_len(skb) and drivers which do not simply pass zero as an
input (in the same way that NULL would be given to can_get_echo_skb()). This
way, we have a nice symmetry between the two echo functions.
Link: https://lore.kernel.org/r/20210111061335.39983-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-13-mkl@pengutronix.de
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Losing arbitration is normal in a CAN-bus network, it means that a higher
priority frame is being send and the pending message will be retried later.
Hence most driver only increment arbitration_lost, but the sja1000 driver also
incremeants tx_error, causing errors to be reported on a normal functioning
CAN-bus. So stop counting them as errors.
Fixes: 8935f57e68 ("can: sja1000: fix network statistics update")
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com
[mkl: split into two seperate patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Support the Classical CAN raw DLC functionality to send and receive DLC values
from 9 .. 15 on various Classical CAN capable CAN network drivers:
- sja1000
- gs_usb
- pcan_usb
- pcan_usb_fd
- usb_8dev
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201111095923.2535-1-socketcan@hartkopp.net
[mkl: usb_8dev: changed indention]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The naming of can_dlc as element of struct can_frame and also as variable
name is misleading as it claims to be a 'data length CODE' but in reality
it always was a plain data length.
With the indroduction of a new 'len' element in struct can_frame we can now
remove can_dlc as name and make clear which of the former uses was a plain
length (-> 'len') or a data length code (-> 'dlc') value.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201120100444.3199-1-socketcan@hartkopp.net
[mkl: gs_usb: keep struct gs_host_frame::can_dlc as is]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The get_can_dlc() macro is used to ensure the payload length information of
the Classical CAN frame to be max 8 bytes (the CAN_MAX_DLEN).
Rename the macro and use the correct constant in preparation of the len/dlc
cleanup for Classical CAN frames.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-3-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Static structure peak_pciec_i2c_bit_ops, of type i2c_algo_bit_data, is
not used except to be copied into another variable. Hence make it const
to protect it from modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Miquel Raynal