Any recovery thread will deadlock when calling qeth_wait_for_threads(), most
notably when triggering a recovery on an OSN device.
This patch will store the recovery thread's task pointer on recovery
invocation and check in qeth_wait_for_threads() respectively to avoid
deadlocks.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
ccw_io_helper neglected to reset vcdev->err after a new channel
program had been successfully started, resulting in stale errors
delivered after one I/O failed. Reset the error after a new
channel program has been successfully started with no old I/O
pending.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The current location for mapping virtio devices does not take
into consideration the standby memory. This causes the failure
of mapping standby memory since the location for the mapping is
already taken by the virtio devices. To fix the problem, we move
the location to beyond the end of standby memory.
Signed-off-by: Nick Wang <jfwang@us.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Tejun writes:
-----
This is the pull request for the earlier patchset[1] with the same
name. It's only three patches (the first one was committed to
workqueue tree) but the merge strategy is a bit involved due to the
dependencies.
* Because the conversion needs features from wq/for-3.10,
block/for-3.10/core is based on rc3, and wq/for-3.10 has conflicts
with rc3, I pulled mainline (rc5) into wq/for-3.10 to prevent those
workqueue conflicts from flaring up in block tree.
* Resolving the issue that Jan and Dave raised about debugging
requires arch-wide changes. The patchset is being worked on[2] but
it'll have to go through -mm after these changes show up in -next,
and not included in this pull request.
The three commits are located in the following git branch.
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git writeback-workqueue
Pulling it into block/for-3.10/core produces a conflict in
drivers/md/raid5.c between the following two commits.
e3620a3ad5 ("MD RAID5: Avoid accessing gendisk or queue structs when not available")
2f6db2a707 ("raid5: use bio_reset()")
The conflict is trivial - one removes an "if ()" conditional while the
other removes "rbi->bi_next = NULL" right above it. We just need to
remove both. The merged branch is available at
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git block-test-merge
so that you can use it for verification. The test merge commit has
proper merge description.
While these changes are a bit of pain to route, they make code simpler
and even have, while minute, measureable performance gain[3] even on a
workload which isn't particularly favorable to showing the benefits of
this conversion.
----
Fixed up the conflict.
Conflicts:
drivers/md/raid5.c
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just a little convenience macro - main reason to add it now is preparing
for immutable bio vecs, it'll reduce the size of the patch that puts
bi_sector/bi_size/bi_idx into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Lars Ellenberg <drbd-dev@lists.linbit.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux-s390@vger.kernel.org
CC: Chris Mason <chris.mason@fusionio.com>
CC: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
You can access it directly now, since 3.8: v3.7-rc1-13-g06ca287
'virtio: move queue_index and num_free fields into core struct
virtqueue.'
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge reason:
From: Alexander Graf <agraf@suse.de>
"Just recently this really important patch got pulled into Linus' tree for 3.9:
commit 1674400aae
Author: Anton Blanchard <anton <at> samba.org>
Date: Tue Mar 12 01:51:51 2013 +0000
Without that commit, I can not boot my G5, thus I can't run automated tests on it against my queue.
Could you please merge kvm/next against linus/master, so that I can base my trees against that?"
* upstream/master: (653 commits)
PCI: Use ROM images from firmware only if no other ROM source available
sparc: remove unused "config BITS"
sparc: delete "if !ULTRA_HAS_POPULATION_COUNT"
KVM: Fix bounds checking in ioapic indirect register reads (CVE-2013-1798)
KVM: x86: Convert MSR_KVM_SYSTEM_TIME to use gfn_to_hva_cache functions (CVE-2013-1797)
KVM: x86: fix for buffer overflow in handling of MSR_KVM_SYSTEM_TIME (CVE-2013-1796)
arm64: Kconfig.debug: Remove unused CONFIG_DEBUG_ERRORS
arm64: Do not select GENERIC_HARDIRQS_NO_DEPRECATED
inet: limit length of fragment queue hash table bucket lists
qeth: Fix scatter-gather regression
qeth: Fix invalid router settings handling
qeth: delay feature trace
sgy-cts1000: Remove __dev* attributes
KVM: x86: fix deadlock in clock-in-progress request handling
KVM: allow host header to be included even for !CONFIG_KVM
hwmon: (lm75) Fix tcn75 prefix
hwmon: (lm75.h) Update header inclusion
MAINTAINERS: Remove Mark M. Hoffman
xfs: ensure we capture IO errors correctly
xfs: fix xfs_iomap_eof_prealloc_initial_size type
...
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The 3270 device nodes 227/0 and 228/0 are special. 227/0 is never used,
and 228/0 is used to redirect full screen applications from /dev/3270/tub
to the real device node of the 3270 terminal.
To keep the device names /dev/3270/tty<x> consistent with the minor number
the device driver sets minor_start to 0 and skips minor 0. That makes the
tty index equivalent to the minor number. But doing so seems to causes
problems with init scripts.
A better solution is to set minor_start to the correct value of 1 and
set name_base to 1 as well. tty_register_device will then automatically
create the correct tty name.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use hex digits when referring to scm addresses.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull networking fixes from David Miller:
1) Fix ARM BPF JIT handling of negative 'k' values, from Chen Gang.
2) Insufficient space reserved for bridge netlink values, fix from
Stephen Hemminger.
3) Some dst_neigh_lookup*() callers don't interpret error pointer
correctly, fix from Zhouyi Zhou.
4) Fix transport match in SCTP active_path loops, from Xugeng Zhang.
5) Fix qeth driver handling of multi-order SKB frags, from Frank
Blaschka.
6) fec driver is missing napi_disable() call, resulting in crashes on
unload, from Georg Hofmann.
7) Don't try to handle PMTU events on a listening socket, fix from Eric
Dumazet.
8) Fix timestamp location calculations in IP option processing, from
David Ward.
9) FIB_TABLE_HASHSZ setting is not controlled by the correct kconfig
tests, from Denis V Lunev.
10) Fix TX descriptor push handling in SFC driver, from Ben Hutchings.
11) Fix isdn/hisax and tulip/de4x5 kconfig dependencies, from Arnd
Bergmann.
12) bnx2x statistics don't handle 4GB rollover correctly, fix from
Maciej Żenczykowski.
13) Openvswitch bug fixes for vport del/new error reporting, missing
genlmsg_end() call in netlink processing, and mis-parsing of
LLC/SNAP ethernet types. From Rich Lane.
14) SKB pfmemalloc state should only be propagated from the head page of
a compound page, fix from Pavel Emelyanov.
15) Fix link handling in tg3 driver for 5715 chips when autonegotation
is disabled. From Nithin Sujir.
16) Fix inverted test of cpdma_check_free_tx_desc return value in
davinci_emac driver, from Mugunthan V N.
17) vlan_depth is incorrectly calculated in skb_network_protocol(), from
Li RongQing.
18) Fix probing of Gobi 1K devices in qmi_wwan driver, and fix NCM
device mode backwards compat in cdc_ncm driver. From Bjørn Mork.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
inet: limit length of fragment queue hash table bucket lists
qeth: Fix scatter-gather regression
qeth: Fix invalid router settings handling
qeth: delay feature trace
tcp: dont handle MTU reduction on LISTEN socket
bnx2x: fix occasional statistics off-by-4GB error
vhost/net: fix heads usage of ubuf_info
bridge: Add support for setting BR_ROOT_BLOCK flag.
bnx2x: add missing napi deletion in error path
drivers: net: ethernet: ti: davinci_emac: fix usage of cpdma_check_free_tx_desc()
ethernet/tulip: DE4x5 needs VIRT_TO_BUS
isdn: hisax: netjet requires VIRT_TO_BUS
net: cdc_ncm, cdc_mbim: allow user to prefer NCM for backwards compatibility
rtnetlink: Mask the rta_type when range checking
Revert "ip_gre: make ipgre_tunnel_xmit() not parse network header as IP unconditionally"
Fix dst_neigh_lookup/dst_neigh_lookup_skb return value handling bug
smsc75xx: configuration help incorrectly mentions smsc95xx
net: fec: fix missing napi_disable call
net: fec: restart the FEC when PHY speed changes
skb: Propagate pfmemalloc on skb from head page only
...
This patch fixes a scatter-gather regression introduced with
commit 5640f768 net: use a per task frag allocator
Now the qeth driver can cope with bigger framents and split a fragment in
sub framents if required.
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give a bad return code when specifying a router setting that is either
invalid or not support on the respective device type. In addition, fall back
the previous setting instead of silently switching back to 'no routing'.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay tracing of the card features until the optional commands have been
enabled.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It allows for cleaning up on a considerable amount of places. They did
port_get, wakeup, kref_put. Now the only thing needed is to call
tty_port_tty_wakeup which does exactly that.
One exception is ifx6x60 where tty_wakeup was open-coded. We now call
tty_wakeup properly there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standby memory that is located outside [0,OLDMEM_SIZE] is currently used
by the s390 memory detection. This leads to additional memory consumption
due to allocation of page structures. To fix this, we now do not
add standby memory if the kernel is started in kdump mode.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let the bus code process scm availability information and
notify scm device drivers about the new state.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stop writing to scm after certain error conditions such as a concurrent
firmware upgrade. Resume to normal state once scm_blk_set_available is
called (due to an scm availability notification).
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Extend the notify callback of scm_driver by an event parameter
to allow to distinguish between different notifications.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a block device driver cannot fetch all requests from the blocklayer
it's in his responsibility to call the request function at a later time.
Normally this would be done after the next irq for the underlying device
is handled. However in situations where we have no outstanding request
we have to schedule the request function for a later time.
This is determined using an internal counter of requests issued to the
hardware.
In some cases where we give a request back to the block layer unhandled
the number of queued requests was not adjusted. Fix this class of
failures by adjusting queued_requests in all functions used to give
a request back to the block layer.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Export the virtio-ccw api in a header for usage by other code.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Lookups by channel/vq pair on host during virtio notifications might be
expensive. Interpret hypercall return value as a cookie which host can
use to do device lookups for the next notification more efficiently.
[CH: Fix line > 80 chars]
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Failfast bit was set incorrectly.
Use set_bit to enable failfast.
Reviewed-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KcDx
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"All trivial, thanks to the stuff which didn't quite make it time"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_console: Initialize guest_connected=true for rproc_serial
virtio: use module_virtio_driver.
virtio: Add module driver macro for virtio drivers.
virtio_console: Use virtio device index to generate port name
virtio: make pci_device_id const
virtio: make config_ops const
virtio-mmio: fix wrong comment about register offset
virtio_console: Let unconnected rproc device receive data.
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
The s390 architecture is unique in respect to dirty page detection,
it uses the change bit in the per-page storage key to track page
modifications. All other architectures track dirty bits by means
of page table entries. This property of s390 has caused numerous
problems in the past, e.g. see git commit ef5d437f71
"mm: fix XFS oops due to dirty pages without buffers on s390".
To avoid future issues in regard to per-page dirty bits convert
s390 to a fault based software dirty bit detection mechanism. All
user page table entries which are marked as clean will be hardware
read-only, even if the pte is supposed to be writable. A write by
the user process will trigger a protection fault which will cause
the user pte to be marked as dirty and the hardware read-only bit
is removed.
With this change the dirty bit in the storage key is irrelevant
for Linux as a host, but the storage key is still required for
KVM guests. The effect is that page_test_and_clear_dirty and the
related code can be removed. The referenced bit in the storage
key is still used by the page_test_and_clear_young primitive to
provide page age information.
For page cache pages of mappings with mapping_cap_account_dirty
there will not be any change in behavior as the dirty bit tracking
already uses read-only ptes to control the amount of dirty pages.
Only for swap cache pages and pages of mappings without
mapping_cap_account_dirty there can be additional protection faults.
To avoid an excessive number of additional faults the mk_pte
primitive checks for PageDirty if the pgprot value allows for writes
and pre-dirties the pte. That avoids all additional faults for
tmpfs and shmem pages until these pages are added to the swap cache.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the DASD devices are detached from the driver, then the
dasd_generic_remove function is called. One of the things this
function should do is to remove the DASD specific sysfs attributes,
but this is not done in all cases. This is likely to cause an oops
when at a later point sysfs stumbles over the stale pointers. In
particular this happens when when the modules are unloaded and loaded
again.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix name clash with some common code device drivers and add "tod"
to all tod clock access function names.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert the defines for the !CONFIG_SCM* stuff to static inline
functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When an attempt to query or modify the grouping state of a channel path
fails due to a timeout, we cannot be sure about its state. To get back to
a defined state, disband the whole path group and try again while excluding
the offending path.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add new attribute "vpm" to the subchannel sysfs directory of I/O
subchannels. This attribute contains a path mask indicating which
channel paths were successfully verified to be usable for I/O.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Omit known to be broken paths (those set in path_noirq_mask) for the
sense/set PGID and nop IO commands.
Note: path_noirq_mask will be reset in ccw_device_verify_start (the
paths could be healthy again). However if we restart a path
verification via verify_start this mask will not be reset (there is
no need to let the wait for an interrupt time out again - plus we
do not want to loop once we deal with the paths in unknown path group
state).
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not abort path verification when waiting for an interrupt timed out.
Use path_noirq_mask to keep track of the paths used for this (also
maintain a path_notoper_mask for debugging purposes). If the timeout
happend to be during an operation where we query or alter the state of
path groups set the pgid_unknown flag.
With this change we allow usage of devices which have such ill-behaved
paths (if at least one path is operational).
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Under LPAR the zfcpdump HSA is a shared resource. Up to now the HSA memory
is released when the zcore file is closed. Dump programs that know that
they do not need the HSA memory any more (e.g. because they already dumped it)
could release it earlier. This would allow other LPARs to use it again.
To achieve this a new debugfs file "hsa" is added that can be used to read
the HSA size and to release the HSA by writing "0" into the file.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cleanup the functions used to call SEI.
Also provide !CONFIG_PCI dummys for pci error handling.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert the synchronous size sense code to an interrupt driven
approach. This allows to set the device online even if the
terminal is not connected. With the new code views can be
registered without a connected terminal, the tty can be opened
as soon as the device is online. After the terminal has been
connected and the size has been determined the tty is resized
to match the device characteristics..
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a notifier to create / destroy the device nodes for the tty view
and the fullscreen view. Only device nodes for online devices are
created and the device names will follow the convention as outlined
in Documentation/devices.txt: 3270/tty<x> for the tty nodes,
3270/tub<x> for hte fullscreen nodes and 3270/tub for the fullscreen
control node.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Corrects the order of tasklet_init vs. the allocation of the
read request which has been broken by git commit 9d2ae233
"TTY: tty3270, move initialization to allocation".
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reintroduce the tty3270_open function which has been removed by
git commit 20cda6f2 "TTY: tty3270, add tty install". Without
the open function in the tty_operations tty_open will return
-ENODEV and the 3270 tty will not work.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is just a table of function pointers, make it const for cleanliness and security
reasons.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio_ccw_setup_vq() failed to unwind correctly on errors. In
particular, it failed to delete the virtqueue on errors, leading to
list corruption when virtio_ccw_del_vqs() iterated over a virtqueue
that had not been added to the vcdev's list.
Fix this with redoing the error unwinding in virtio_ccw_setup_vq(),
using a single path for all errors.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 46d3ceab "tcp: TCP Small Queues" has severly degraded
performance for single connection RR workloads on HiperSockets with
MTU >=16K due to a conflict of the TCP Small Queues approach with our
buffer scan threshold which releases buffers not frequently enough yet.
This fix restores performance to the same level as before cited commit.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now, s390dbf entries for the cards are discarded as soon as the
device is removed. However, this will also bar us of all chances of
getting valuable debug information after a device has been removed.
This patch will keep the s390dbf entries around until the qeth module
is removed.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refer to virtual NICs instead of GuestLANs.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing port isolation mode 'forward' will now verify that the adjacent
switch port supports the required reflective relay (RR) mode. This patch adds
the required error handling for the cases where enabling port isolation mode
'forward' can now fail.
Furthermore, once established, we never fall back from one of the port
isolation modes to a non-isolated mode without further user-interaction.
This includes cases where the isolation mode was enabled successfully, but
ceases to work e.g. due to configuration changes at the switch port.
Finally, configuring an isolation mode with the device being offline
will make onlining the device fail permanently upon errors encountered until
either errors are resolved or the isolation mode is changed by the user to a
different mode.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove exports that are not used anywhere else.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code did never retry any idx setup unless retries were done
for device offline/online at the beginning of the function.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cbc0dd1 "s390/pci: CHSC PCI support for error and availability events"
introduced a new SEI notification type as part of pci support.
The way SEI was called with nt2 and nt0 consecutive broke the nt0
stuff used for channel subsystem notifications.
The reason why this was broken with the mentioned patch is that you
cannot selectively disable type 0 notifications (so even when asked
for type 2 only, type 0 could be presented).
The way to do it is to tell SEI which types of notification you can
process and -this is the important part- look at the SEI result which
notification type you actually received.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
This is the last one: tty_schedule_flip
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One point is to have less places where we actually need tty pointer.
The other is that low_latency is bound to buffer processing and
buffers are now in tty_port. So it makes sense to move low_latency to
tty_port too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases a virtio command might try to issue a ccw before a former
ccw was answered with a tsch. This will cause CC=2 (busy). Lets just
retry in that case.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Dynamically allocate any data structures like ccw used when
doing channel I/O. Otherwise, we'd need to add extra serialization
for the different callbacks using the same data structures.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Partially revert ae289dc1f "s390/3215: fix tty close handling", since this
leads sometimes to hanging agetty processes and therefore systems that get
stuck while starting.
This was magically fixed (bisected) by a common code patch from Alan Cox:
36b3c070 "tty: Move the handling of the tty release logic", however it was
unrelated.
Since the removed code worked for a decade, nobody knows anymore why it was
in there in the first place and debugging the observed hang is non-trivial
(at least for me :) ), let's just re-add the removed code before we see
other side effects.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Now that irq sum accounting for /proc/stat's "intr" line works again we
have the oddity that the sum field (first field) contains only the sum
of the second (external irqs) and third field (I/O interrupts).
The reason for that is that these two fields are already sums of all other
fields. So if we would sum up everything we would count every interrupt
twice.
This is broken since the split interrupt accounting was merged two years
ago: 052ff461c8 "[S390] irq: have detailed
statistics for interrupt types".
To fix this remove the split interrupt fields from /proc/stat's "intr"
line again and only have them in /proc/interrupts.
This restores the old behaviour, seems to be the only sane fix and mimics
a behaviour from other architectures where /proc/interrupts also contains
more than /proc/stat's "intr" line does.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For more than two years, since f2c66cd8ee
"/proc/stat: scalability of irq num per cpu" the output of /proc/stat is
broken.
The first field in the "intr" line should contain the sum of all interrupts,
however since the above mentioned change it is always zero.
The reason for that is that a per cpu irq sum variable had been introduced
which got incremented when calling kstat_incr_irqs_this_cpu(). However
on s390 we directly incremented only the per cpu per irq counter by accessing
the array element via kstat_cpu(smp_processor_id()).irqs[...].
So fix this and use the kstat_incr_irqs_this_cpu() wrapper which increments
both: the per cpu per irq counter and the per cpu irq sum counter.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also benefit from rcu_read_lock held and use __in_dev_get_rcu() in ipv4 case.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for kvm guests that matches virtual ccw devices provided
by the host as virtio bridge devices.
These virtio-ccw devices use a special set of channel commands in order
to perform virtio functions.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Running under a kvm host does not necessarily imply the presence of
a page mapped above the main memory with the virtio information;
however, the code includes a hard coded access to that page.
Instead, check for the presence of the page and exit gracefully
before we hit an addressing exception if it does not exist.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
cc: stable@vger.kernel.org
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Pull s390 update from Martin Schwidefsky:
"Add support to generate code for the latest machine zEC12, MOD and XOR
instruction support for the BPF jit compiler, the dasd safe offline
feature and the big one: the s390 architecture gets PCI support!!
Right before the world ends on the 21st ;-)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (41 commits)
s390/qdio: rename the misleading PCI flag of qdio devices
s390/pci: remove obsolete email addresses
s390/pci: speed up __iowrite64_copy by using pci store block insn
s390/pci: enable NEED_DMA_MAP_STATE
s390/pci: no msleep in potential IRQ context
s390/pci: fix potential NULL pointer dereference in dma_free_seg_table()
s390/pci: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
s390/bpf,jit: add support for XOR instruction
s390/bpf,jit: add support MOD instruction
s390/cio: fix pgid reserved check
vga: compile fix, disable vga for s390
s390/pci: add PCI Kconfig options
s390/pci: s390 specific PCI sysfs attributes
s390/pci: PCI hotplug support via SCLP
s390/pci: CHSC PCI support for error and availability events
s390/pci: DMA support
s390/pci: PCI adapter interrupts for MSI/MSI-X
s390/bitops: find leftmost bit instruction support
s390/pci: CLP interface
s390/pci: base support
...
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
For each detected qdio device a line like to following is printed:
qdio: 0.0.4102 OSA on SC 1045 using AI:1 QEBSM:0 PCI:1 TDD:1 SIGA: W AP
The PCI flag is misleading as this stands for "program controlled interrupt".
Rename it to PRI "program requested interrupt" which is more accurate and
does not interfere with another popular piece of technology.
Leave the pci string in the code since changing that would result in a huge
patch.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The check to whom a device is reserved is done by checking the path
state of the affected channel paths. If it turns out that one path is
flagged as reserved by someone else the whole device is marked as such.
However the meaning of the RESVD_ELSE bit is that the addressed device
is reserved to a different pathgroup (and not reserved to a different
LPAR). If we do this test on a path which is currently not a member of
the pathgroup we could erroneously mark the device as reserved to
someone else.
To fix this collect the reserved state for all potential members of the
pathgroup and only mark the device as reserved if all of those potential
members have the RESVD_ELSE bit set.
Cc: stable@vger.kernel.org
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add SCLP PCI configure/deconfigure and implement a PCI hotplug
controller (s390_pci_hpc). The hotplug controller creates a slot
for every PCI function in stand-by or configured state. The PCI
functions are named after the PCI function ID (fid). By writing to
the power attribute in /sys/bus/pci/slots/<fid>/power the PCI function
is moved to stand-by or configured state. If moved to the configured
state the device is automatically scanned by the s390 PCI layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add CHSC store-event-information support for PCI (notfication type 2)
and report error and availability events to the PCI architecture layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The regular behavior of the DASD device driver when setting a device
offline is to return all outstanding I/O as failed. This behavior is
different from that of other System z operating systems and may lead
to unexpected data loss. Adding an explicit 'safe' offline function
will allow customers to use DASDs in the way they expect them to work.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a channel path is cabled incorrectly and the device is suspended and
resumed the device may be inaccessible afterwards.
Make the path connection check not interrupt the resume callback there
could be other valid paths available.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Reference-ID: RQM 1262
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow drivers to enable/disable ccwgroup devices.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Return -EINVAL if set_{on,off}line is called for already {on,off}line
devices. Also return -EINVAL for drivers which do not provide a callback
for set_{on,off}line. This behaviour is now consistent with the one for
ccw devices.
Reported-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move and rename init_storage_keys() to pageattr.c, so it can also be
used from the sclp memory hotplug code in order to initialize
storage keys.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The message request handling (type50 - clear key) for RSA operations
(in CRT format) are now handled correctly with respect to the crb
format container.
Signed-off-by: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let the dasd driver and qdio use ccw_device_get_schid and
get rid of other similar functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This will be needed by the new virtio-ccw transport.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove or replace BUG/BUG_ON where possible and convert WARN_ON
to WARN_ON_ONCE if they can occur freqeuently as pointed out by:
https://lkml.org/lkml/2012/9/27/461
Checks have been removed if:
- the error condition leads to a hardware error which gets logged
and in most cases stops the device
- the error condition is a null pointer access
- the error condition is just pointless or already handled at
another location
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not use more than one KERN_<level> per printk.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove BUG_ONs or convert to WARN_ON_ONCE/WARN_ONs since a failure within a
networking device driver is no reason to shut down the entire machine.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trace all supported and enabled card features to s390dbf.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, virtual NICs whether attached to a VSWITCH or a guest LAN were always
displayed as guest LANs in the device driver attributes and messages, while
in fact it is a virtual NIC.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove BUG_ON's in claw driver, since the checked error conditions
are null pointer accesses.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove BUG_ON's in ctcm driver, since the checked error conditions
are null pointer accesses.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate a variable that is never modified.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"Whether" is misspelled in various comments across the tree; this
fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull networking updates from David Miller:
1) tx_filtered/ps_tx_buf queues need to be accessed with the SKB queue
lock, from Arik Nemtsov.
2) Don't call 802.11 driver's filter configure method until it's
actually open, from Felix Fietkau.
3) Use ieee80211_free_txskb otherwise we leak control information.
From Johannes Berg.
4) Fix memory leak in bluetooth UUID removal,f rom Johan Hedberg.
5) The shift mask trick doesn't work properly when 'optname' is out of
range in do_ip_setsockopt(). Use a straightforward switch statement
instead, the compiler emits essentially the same code but without
the missing range check. From Xi Wang.
6) Fix when we call tcp_replace_ts_recent() otherwise we can
erroneously accept a too-high tsval. From Eric Dumazet.
7) VXLAN bug fixes, mostly to do with VLAN header length handling, from
Alexander Duyck.
8) Missing return value initialization for IPV6_MINHOPCOUNT socket
option handling. From Hannes Frederic.
9) Fix regression in tasklet handling in jme/ksz884x/xilinx drivers,
from Xiaotian Feng.
10) At smsc911x driver init time, we don't know if the chip is in word
swap mode or not. However we do need to wait for the control
register's ready bit to be set before we program any other part of
the chip. Adjust the wait loop to account for this. From Kamlakant
Patel.
11) Revert erroneous MDIO bus unregister change to mdio-bitbang.c
12) Fix memory leak in /proc/net/sctp/, from Tommi Rantala.
13) tilegx driver registers IRQ with NULL name, oops, from Simon Marchi.
14) TCP metrics hash table kzalloc() based allocation can fail, back
down to using vmalloc() if it does. From Eric Dumazet.
15) Fix packet steering out-of-order delivery regression, from Tom
Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net-rps: Fix brokeness causing OOO packets
tcp: handle tcp_net_metrics_init() order-5 memory allocation failures
batman-adv: process broadcast packets in BLA earlier
batman-adv: don't add TEMP clients belonging to other backbone nodes
batman-adv: correctly pass the client flag on tt_response
batman-adv: fix tt_global_entries flags update
tilegx: request_irq with a non-null device name
net: correct check in dev_addr_del()
tcp: fix retransmission in repair mode
sctp: fix /proc/net/sctp/ memory leak
Revert "drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free"
net/smsc911x: Fix ready check in cases where WORD_SWAP is needed
drivers/net: fix tasklet misuse issue
ipv4/ip_vti.c: VTI fix post-decryption forwarding
brcmfmac: fix typo in CONFIG_BRCMISCAN
vxlan: Update hard_header_len based on lowerdev when instantiating VXLAN
vxlan: fix a typo.
ipv6: setsockopt(IPIPPROTO_IPV6, IPV6_MINHOPCOUNT) forgot to set return value
doc/net: Fix typo in netdev-features.txt
vxlan: Fix error that was resulting in VXLAN MTU size being 10 bytes too large
...
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
To be sure, the TTY buffers (and later some stuff) are gone along with
the tty_port, we have to call tty_port_destroy at tear-down places.
This is mostly where the structure containing a tty_port is freed.
This patch does exactly that -- put tty_port_destroy at those places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 3215 console always has the RAW3215_FIXED flag set, which causes
raw3215_shutdown() not to wait for outstanding I/O requests if an attached
tty gets closed.
The flag however can be simply removed, so we can guarantee that all requests
belonging to the tty have been processed when the tty is closed.
However the tasklet that belongs to the 3215 device may be scheduled even if
there is no tty attached anymore, since we have a race between console and tty
processing.
Thefore unconditional tty_wakekup() in raw3215_wakeup() can cause the following
NULL pointer dereference:
3.465368 Unable to handle kernel pointer dereference at virtual kernel address (null)
3.465448 Oops: 0004 #1 SMP
3.465454 Modules linked in:
3.465459 CPU: 1 Not tainted 3.6.0 #1
3.465462 Process swapper/1 (pid: 0, task: 000000003ffa4428, ksp: 000000003ffb7ce0)
3.465466 Krnl PSW : 0404100180000000 0000000000162f86 (__wake_up+0x46/0xb8)
3.465480 R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:1 PM:0 EA:3
Krnl GPRS: fffffffffffffffe 0000000000000000 0000000000000160 0000000000000001
3.465492 0000000000000001 0000000000000004 0000000000000004 000000000096b490
3.465499 0000000000000001 0000000000000100 0000000000000001 0000000000000001
3.465506 070000003fc87d60 0000000000000160 000000003fc87d68 000000003fc87d00
3.465526 Krnl Code: 0000000000162f76: e3c0f0a80004 lg %r12,168(%r15)
0000000000162f7c: 58000370 l %r0,880
#0000000000162f80: c007ffffffff00 xilf %r0,4294967295
>0000000000162f86: ba102000 cs %r1,%r0,0(%r2)
0000000000162f8a: 1211 ltr %r1,%r1
0000000000162f8c: a774002f brc 7,162fea
0000000000162f90: b904002d lgr %r2,%r13
0000000000162f94: b904003a lgr %r3,%r10
3.465597 Call Trace:
3.465599 (<0400000000000000> 0x400000000000000)
3.465602 <000000000048c77e> raw3215_wakeup+0x2e/0x40
3.465607 <0000000000134d66> tasklet_action+0x96/0x168
3.465612 <000000000013423c> __do_softirq+0xd8/0x21c
3.465615 <0000000000134678> irq_exit+0xa8/0xac
3.465617 <000000000046c232> do_IRQ+0x182/0x248
3.465621 <00000000005c8296> io_return+0x0/0x8
3.465625 <00000000005c7cac> vtime_stop_cpu+0x4c/0xb8
3.465629 (<0000000000194e06> tick_nohz_idle_enter+0x4e/0x74)
3.465633 <0000000000104760> cpu_idle+0x170/0x184
3.465636 <00000000005b5182> smp_start_secondary+0xd6/0xe0
3.465641 <00000000005c86be> restart_int_handler+0x56/0x6c
3.465643 <0000000000000000> 0x0
3.465645 Last Breaking-Event-Address:
3.465647 <0000000000403136> tty_wakeup+0x46/0x98
3.465652
3.465654 Kernel panic - not syncing: Fatal exception in interrupt
01: HCPGIR450W CP entered; disabled wait PSW 00020001 80000000 00000000 0010F63C
The easiest solution is simply to check if tty is NULL in the tasklet.
If it is NULL nothing is to do (no tty attached), otherwise tty_wakeup()
can be called, since we hold a reference to the tty.
This is not nice... but it is a small patch and it works.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the set_mac_address() function of qeth is invoked, qeth deletes
the old mac address first on OSA. Only if deletion returns
successfully the new mac address is set on OSA. Deletion may return
with a return value "MAC not found on OSA". In this case qeth
should continue setting the new mac address.
When the OSA cable is pulled, OSA forgets any set mac address. If
the OSA network interface acts as a slave to a bonding master
interface, bonding can invoke the set_mac_address function for
failover purposes and depends on successful setting of the new mac
address even though the old mac address could no longer be deleted.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return codes of IPA_CMD_QIPASSIST are not checked, especially the ones which
indicate that the command is not supported. As a result, the device driver
would not enable all available features on older card generations.
This patch adds proper checking and sets the bare minimum in the supported
functions flags to avoid follow-on errors.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bitmap_or uses the number of bits as its length parameter and
not the number of words necessary to store those bits.
This fixes a regression introduced by:
aa92b33 s390/cio: use generic bitmap functions
Reported-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There's no need to keep __MAX_SUBCHANNEL and __MAX_SSID private to the
common I/O layer when __MAX_CSSID is usable by everybody.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not trigger a path verification in the subchannel event
function during resume from hibernate. This will be started
by the pm_restore callback later.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Receiving cc=3 from store subchannel means 2 things:
* the subchannel is not provided
* there are no further subchannels in this subchannel set
With this patch we abort the store subchannel loop after cc=3 (or an
exception) and clear the subsequent bits in the subchannel id set.
Reported-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use generic bitmap functions in the subchannel id bitmap to
simplify and de-bloat the code.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The recovery thread, when failing, tears down the respective interface. To do
so, it needs to obtain the rtnl lock first, as the interface configuration is
changed.
If another process tries to modify an interface setting at the same time, that
process can obtain the rtnl lock first, but the respective callback in the qeth
driver will block until recovery has completed - which cannot happen since the
calling process already obtained it.
In one particular case, the bonding driver acquired the rtnl lock to modify the
card's MAC address, while the recovery failed at the same time due to the card
being removed. Hence qeth_l2_set_mac_address (implicitly holding the rtnl lock)
was waiting on qeth_l2_recover, which deadlocked when waiting on the rtnl lock.
This patch uses rtnl_trylock instead of rtnl_lock in the recovery thread. If the
lock cannot be obtained, the interface will be left up, but the card state
remains in CARD_STATE_RECOVER, which will prevent any further activities on the
card.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsg_pm_restore_thaw() uses wrong checking before reconnecting
the IUCV path to *MSG. It is corrected with this patch.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Let the driver core handle device attribute creation and removal. This
will simplify the code and eliminates races between attribute
availability and userspace notification via uevents.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull virtio changes from Rusty Russell:
"New workflow: same git trees pulled by linux-next get sent straight to
Linus. Git is awkward at shuffling patches compared with quilt or mq,
but that doesn't happen often once things get into my -next branch."
* 'virtio-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (24 commits)
lguest: fix occasional crash in example launcher.
virtio-blk: Disable callback in virtblk_done()
virtio_mmio: Don't attempt to create empty virtqueues
virtio_mmio: fix off by one error allocating queue
drivers/virtio/virtio_pci.c: fix error return code
virtio: don't crash when device is buggy
virtio: remove CONFIG_VIRTIO_RING
virtio: add help to CONFIG_VIRTIO option.
virtio: support reserved vqs
virtio: introduce an API to set affinity for a virtqueue
virtio-ring: move queue_index to vring_virtqueue
virtio_balloon: not EXPERIMENTAL any more.
virtio-balloon: dependency fix
virtio-blk: fix NULL checking in virtblk_alloc_req()
virtio-blk: Add REQ_FLUSH and REQ_FUA support to bio path
virtio-blk: Add bio-based IO path for virtio-blk
virtio: console: fix error handling in init() function
tools: Fix pthread flag for Makefile of trace-agent used by virtio-trace
tools: Add guest trace agent as a user tool
virtio/console: Allocate scatterlist according to the current pipe size
...
This is a large set of updates, mostly for drivers (qla2xxx [including support
for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape
adding virtually unlimited numbers of tape drives plus a set of dif fixes for
sd and a fix for a live lock on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
=49u9
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
As we skipped the merge window for 3.6-rc1 for the tty tree, everything
is now settled down and working properly, so we are ready for 3.7-rc1.
Here's the patchset, it's big, but the large changes are removing a
firmware file and adding a staging tty driver (it depended on the tty
core changes, so it's going through this tree instead of the staging
tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp36oACgkQMUfUDdst+yk4WgCdEy13hot8fI2Lqnc7W0LKu7GX
4p8AoLTjzrXhLosxdijskDQ9X1OtjrxU
=S5Ng
-----END PGP SIGNATURE-----
Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY changes from Greg Kroah-Hartman:
"As we skipped the merge window for 3.6-rc1 for the tty tree,
everything is now settled down and working properly, so we are ready
for 3.7-rc1. Here's the patchset, it's big, but the large changes are
removing a firmware file and adding a staging tty driver (it depended
on the tty core changes, so it's going through this tree instead of
the staging tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up more-or-less trivial conflicts in
- drivers/char/pcmcia/synclink_cs.c:
tty NULL dereference fix vs tty_port_cts_enabled() helper function
- drivers/staging/{Kconfig,Makefile}:
add-add conflict (dgrp driver added close to other staging drivers)
- drivers/staging/ipack/devices/ipoctal.c:
"split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"
* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
tty/serial: Add kgdb_nmi driver
tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
tty/serial/amba-pl011: Implement poll_init callback
tty/serial/core: Introduce poll_init callback
kdb: Turn KGDB_KDB=n stubs into static inlines
kdb: Implement disable_nmi command
kernel/debug: Mask KGDB NMI upon entry
serial: pl011: handle corruption at high clock speeds
serial: sccnxp: Make 'default' choice in switch last
serial: sccnxp: Remove mask termios caps for SW flow control
serial: sccnxp: Report actual baudrate back to core
serial: samsung: Add poll_get_char & poll_put_char
Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
Powerpc 8xx CPM_UART maxidl should not depend on fifo size
Powerpc 8xx CPM_UART too many interrupts
Powerpc 8xx CPM_UART desynchronisation
serial: set correct baud_base for EXSYS EX-41092 Dual 16950
serial: omap: fix the reciever line error case
8250: blacklist Winbond CIR port
8250_pnp: do pnp probe before legacy probe
...
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio network device multiqueue support reserves
vq 3 for future use (useful both for future extensions and to make it
pretty - this way receive vqs have even and transmit - odd numbers).
Make it possible to skip initialization for
specific vq numbers by specifying NULL for name.
Document this usage as well as (existing) NULL callback.
Drivers using this not coded up yet, so I simply tested
with virtio-pci and verified that this patch does
not break existing drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Instead of storing the queue index in transport-specific virtio structs,
this patch moves them to vring_virtqueue and introduces an helper to get
the value. This lets drivers simplify their management and tracing of
virtqueues.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A common way to prepare a z/VM mini disk is to format the real device
with a z/VM tool like CPFMTXA and then define a mini disk that excludes
the first cylinder, i.e. the cylinder 0 of the virtual disk is located
at cylinder 1 of the real device.
The DASD device driver will recognize such a mini disk as formatted, as
the uniform record layout on the disk matches that of an LDL formatted
device. However, the cylinder value in the 'count' field of the ECKD
records matches the geometry of the real device, and not that of the
mini disk, so I/O requests will fail with 'record not found' errors.
To make the mini disk usable, it needs to be formatted with a tool like
dasdfmt. To enable tools like distribution installation tools to
recognize this situation, the DASD device driver should report such a
mini disk as 'not formatted'.
To this end we need to extend the device recognition code to check not
just for proper record sizes, but also for proper cylinder/head/record
values.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Reviewed-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of these:
arch/s390/kernel/smp.c:134:19: warning: ‘status’ may be used uninitialized in this function [-Wuninitialized]
arch/s390/mm/pgtable.c:641:10: warning: ‘table’ may be used uninitialized in this function [-Wuninitialized]
arch/s390/mm/pgtable.c:644:12: warning: ‘page’ may be used uninitialized in this function [-Wuninitialized]
drivers/s390/cio/cio.c:1037:14: warning: ‘schid’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this compile error:
In file included from drivers/s390/char/tape_core.c:29:0:
drivers/s390/char/tape_std.h:103:66: warning: ‘struct request’ declared inside parameter list [enabled by default]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of this compile warning for CONFIG_32BIT:
drivers/s390/crypto/ap_bus.c:168:12: warning: ‘ap_configuration_available’
defined but not used [-Wunused-function]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Calling debug_event the s390 debug feature only logs up to buf_size
bytes of the debug view. If debug_event is called with more bytes
than buf_size the additional data is ignored and not logged in the
debug view.
Use multiple calls to debug_event if the length exceeds buf_size.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Detect external AP bus configuration changes and request
an AP device rescan.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Changing the return value of vmlogrdr_open() to -EOPNOTSUPP if O_NONBLOCK
is specified shouldn't have any negative side effects.
Any existing user wouldn't specify that flag since it wouldn't work anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change -ENOSYS to -EOPNOTSUPP. Return value is used only internally.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The return value was only internally used, so it's ok to change.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For non-existent ioctls -ENOTTY should be returned.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change return code handling of the stsi() function:
In case function code 0 was specified the return value is the
current configuration level (already shifted). That way all
the code that actually copied the stsi_0() function can go
away.
Otherwise the return value is 0 (success) or negative to
indicate an error (currently only -EOPNOTSUPP).
Also stsi() is no longer an inline function. The function is
not performance critical, but every caller would generate an
exception table entry for this function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I was checking why this spinlock was never initialized, but it turns
out it's not used anywhere, so we can drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not reset drvdata before the block device is cleaned up. With a
non-empty block queue drvdata could be accessed.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the spinlock from struct scm_device. drvdata and attributes
are guarded via device_lock.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Force writes to Storage Class Memory (SCM) to be in done in clusters.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Block device driver for Storage Class Memory (SCM). This driver
provides a block device interface for each available SCM increment.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for EADM interrupt statistics in /proc/interrupts.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This driver allows usage of EADM subchannels. EADM subchannels
act as a communication vehicle for SCM increments.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Detect an scm change notification in store event information.
Update affected scm devices and notify their drivers.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Bus driver to manage Storage Class Memory.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
chsc_scm_info will be used to detect all available increments of
storage class memory.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add structures to be used by the eadm subchannel driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add the eadm facility bits to the css characteristics and move
them to a new header.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow subchannel drivers build as a module to schedule subchannel work.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Msgtype implementations are now separated from card specific modules
and can be dynamically registered. Existing msgtype implementations
are restructured in modules.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add the function facility information as new ap_device and sysfs
attribute. Also make the number of requests in device
queue and in device driver queue accessible in sysfs.
Reviewed-by: Ingo Tuchscherer <ingo.tuchscherer@linux.vnet.ibm.com>
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Query AP configuration information. Improve performance of AP bus
scans by skipping AP device probing, if the AP deviec is not
configured.
Reviewed-by: Ingo Tuchscherer <ingo.tuchscherer@linux.vnet.ibm.com>
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
removes unnecessary semicolon
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipaddr has been allocated in function qeth_l3_add_vipa() but
does not free before leaving from the error handling cases. The
same problem also exists in function qeth_l3_add_rxip().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that all ccws used for writing are initialized with
zeros - especially since the last ccw contains a TIC for which
the unused fields have to be zeros.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the qeth_get_channel_path_desc function and rename it
to qeth_update_from_chp_desc. No functional change.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Acked-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__scsi_remove_device (e.g. due to dev_loss_tmo) calls
zfcp_scsi_slave_destroy which in turn sends a close LUN FSF request to
the adapter. After 30 seconds without response,
zfcp_erp_timeout_handler kicks the ERP thread failing the close LUN
ERP action. zfcp_erp_wait in zfcp_erp_lun_shutdown_wait and thus
zfcp_scsi_slave_destroy returns and then scsi_device is no longer
valid. Sometime later the response to the close LUN FSF request may
finally come in. However, commit
b62a8d9b45
"[SCSI] zfcp: Use SCSI device data zfcp_scsi_dev instead of zfcp_unit"
introduced a number of attempts to unconditionally access struct
zfcp_scsi_dev through struct scsi_device causing a use-after-free.
This leads to an Oops due to kernel page fault in one of:
zfcp_fsf_abort_fcp_command_handler, zfcp_fsf_open_lun_handler,
zfcp_fsf_close_lun_handler, zfcp_fsf_req_trace,
zfcp_fsf_fcp_handler_common.
Move dereferencing of zfcp private data zfcp_scsi_dev allocated in
scsi_device via scsi_transport_reserve_device after the check for
potentially aborted FSF request and thus no longer valid scsi_device.
Only then assign sdev_to_zfcp(sdev) to the local auto variable struct
zfcp_scsi_dev *zfcp_sdev.
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> #2.6.37+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In FC fabrics with large zones, the automatic port_rescan on incoming ELS
and any adapter recovery can cause quite some traffic at the very same
time, especially if lots of Linux images share an HBA, which is common on
s390. This can cause trouble and failures. Fix this by making such port
rescans dependent on a user configurable module parameter.
The following unconditional automatic port rescans remain as is:
On setting an adapter online and
on manual user-triggered writes to the sysfs attribute port_rescan.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Upstream commit f3450c7b91
"[SCSI] zfcp: Replace local reference counting with common kref"
accidentally dropped a reference count check before tearing down
zfcp_ports that are potentially in use by zfcp_units.
Even remote ports in use can be removed causing
unreachable garbage objects zfcp_ports with zfcp_units.
Thus units won't come back even after a manual port_rescan.
The kref of zfcp_port->dev.kobj is already used by the driver core.
We cannot re-use it to track the number of zfcp_units.
Re-introduce our own counter for units per port
and check on port_remove.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@vger.kernel.org> #2.6.33+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If list_for_each_entry, etc complete a traversal of the list, the iterator
variable ends up pointing to an address at an offset from the list head,
and not a meaningful structure. Thus this value should not be used after
the end of the iterator. Replace port->adapter->scsi_host by
adapter->scsi_host.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/).
Oversight in upsteam commit of v2.6.37
a1ca48319a
"[SCSI] zfcp: Move ACL/CFDC code to zfcp_cfdc.c"
which merged the content of zfcp_erp_port_access_changed().
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> #2.6.37+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the mapping of FCP device bus ID and corresponding subchannel
is modified while the Linux image is suspended, the resume of FCP
devices can fail. During resume, zfcp gets callbacks from cio regarding
the modified subchannels but they can be arbitrarily mixed with the
restore/resume callback. Since the cio callbacks would trigger
adapter recovery, zfcp could wakeup before the resume callback.
Therefore, ignore the cio callbacks regarding subchannels while
being suspended. We can safely do so, since zfcp does not deal itself
with subchannels. For problem determination purposes, we still trace the
ignored callback events.
The following kernel messages could be seen on resume:
kernel: <WWPN>: parent <FCP device bus ID> should not be sleeping
As part of adapter reopen recovery, zfcp performs auto port scanning
which can erroneously try to register new remote ports with
scsi_transport_fc and the device core code complains about the parent
(adapter) still sleeping.
kernel: zfcp.3dff9c: <FCP device bus ID>:\
Setting up the QDIO connection to the FCP adapter failed
<last kernel message repeated 3 more times>
kernel: zfcp.574d43: <FCP device bus ID>:\
ERP cannot recover an error on the FCP device
In such cases, the adapter gave up recovery and remained blocked along
with its child objects: remote ports and LUNs/scsi devices. Even the
adapter shutdown as part of giving up recovery failed because the ccw
device state remained disconnected. Later, the corresponding remote
ports ran into dev_loss_tmo. As a result, the LUNs were erroneously
not available again after resume.
Even a manually triggered adapter recovery (e.g. sysfs attribute
failed, or device offline/online via sysfs) could not recover the
adapter due to the remaining disconnected state of the corresponding
ccw device.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> #2.6.32+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The pl vector has scount elements, i.e. pl[scount-1] is the last valid
element. For maximum sized requests, payload->counter == scount after
the last loop iteration. Therefore, do bounds checking first (with
boolean shortcut) to not access the invalid element pl[scount].
Do not trust the maximum sbale->scount value from the HBA
but ensure we won't access the pl vector out of our allocated bounds.
While at it, clean up scoping and prevent unnecessary memset.
Minor fix for 86a9668a8d
"[SCSI] zfcp: support for hardware data router"
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> #3.2+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Duplicate fssrh_2 from a54ca0f62f
"[SCSI] zfcp: Redesign of the debug tracing for HBA records."
complicates distinction of generic status read response from
local link up.
Duplicate fsscth1 from 2c55b750a8
"[SCSI] zfcp: Redesign of the debug tracing for SAN records."
complicates distinction of good common transport response from
invalid port handle.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> #2.6.38+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit a9277e7783
"[SCSI] scsi_transport_fc: Getting FC Port Speed in sync with FC-GS"
changed the semantics of FC_PORTSPEED defines to
FDMI port attributes of FC-HBA/SM-HBA
which is different from the previous bit reversed
Report Port Speed Capabilities (RPSC) ELS of FC-GS/FC-LS.
Zfcp showed "10 Gbit" instead of "4 Gbit" for supported_speeds.
It now uses explicit bit conversion as the other LLDs already
do, in order to be independent of the kernel bit semantics.
See also http://marc.info/?l=linux-scsi&m=134452926830730&w=2
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> #3.4+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Read unit address is done for all devices during online processing to read
out LCU features. This is also done after disconnect/connect a LCU.
Some older storage hardware does not provide the capability to read unit
address configuration.
This leads to a loop trying to read unit address configuration every 30
seconds. The device is still operational but logs are flooded with error
messages.
Fix the loop by recognizing a command reject saying that the suborder
for ruac is not supported.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a new path is available we need to verify the path data. If it is the
first path for a device the stop bits are removed after path verification.
If a pathgroup is established we need to set system characteristics for
the lcu. Therefore I/O has to be started.
If the device is stopped the set system characteristics worker may block
the path verification worker and the device is blocked.
Turn on failfast for set system characteristics CQR to prevent a deadlock
with the path verification worker.
If a pathgroup is established on a device that is not in use trigger path
verification. Maybe we were not informed about a working path.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Reviewed-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure that the cdev pointer for IO subchannels is set to NULL when
we deregister the device (and release its last reference). This will
fix a bug were another process operates on an already freed ccw device.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the subchannel event function is called from IRQ context and we
observe that the subchannel in question is gone we flag the attached
device as not operational and schedule the event function to be called
again from process context where the subchannel gets deregistered.
However if the subchannel reappeared at the time the event function
gets called from process context we would do nothing and leave the
device in not operational state. Recognize this case in sch_get_action
and trigger reexamination of the subchannel/device.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure that all work is done when the process waiting for a
dasd state change is woken up. With this change it is save
to assume that after a userspace triggered state change and
a udev settle invocation there are no unexpected users of a
dasd device.
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For unimplemented ioctls the dasd driver should return -ENOTTY.
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
In this case ->install is the only thing we want to do. We do not need
->open at all. See the tty->count > 1 check.
And since we take a reference in ->install, we need also ->cleanup to
drop the reference to a view.
Final note, see that we leave raw3270_find_view in place. It is
because views are removed even from module_exit.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
raw3215[line] is set in probe, but not unset in remove. This will lead
to random crashes if the device is removed and the corresponding tty
opened later. open would dereference freed memory.
So set raw3215[line] to NULL in remove to fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So now for those drivers that can use neither tty_port_install nor
tty_port_register_driver but still have tty_port available before
tty_register_driver we use newly added tty_port_link_device.
The rest of the drivers that still do not provide tty_struct <->
tty_port link will have to be converted to implement
tty->ops->install.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This looks like it was a mistake not to create device nodes for these
drivers. Let us create them from now on.
It will be necessary to call tty_register_device some way, either by
tty_register_driver implicitly or to call tty_register_device proper.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: netdev@vger.kernel.org
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Cc: linux-cris-kernel@axis.com
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On module unload, in tty3270_exit, we forgot to free the tty driver.
Add there a call to put_tty_driver.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the last block of the HSA is read, EVSTATE_ALL_STORED is returned
by SCLP. Because of a missing break in the switch statement two trace
entries are written in this case: "all stored" and "part stored".
This patch adds the missing break and also adds a "fall through"
comment to improve the readability.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reported-by: David A Gilbert <DavidAGilbert@uk.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull networking updates and fixes from David Miller:
1) Reinstate the no-ref optimization for input route lookups in ipv4 to
fix some routing cache removal perf regressions.
2) Make TCP socket pre-demux work on ipv6 side too, from Eric Dumazet.
3) Get RX hash value from correct place in be2net driver, from
Sarveshwar Bandi.
4) Validation of FIB cached routes missing critical check, from Eric
Dumazet.
5) EEH support in mlx4 driver, from Kleber Sacilotto de Souza.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
ipv6: Early TCP socket demux
ipv4: Fix input route performance regression.
pch_gbe: vlan skb len fix
pch_gbe: add extra clean tx
pch_gbe: fix transmit watchdog timeout
ixgbe: fix panic while dumping packets on Tx hang with IOMMU
be2net: Fix to parse RSS hash from Receive completions correctly.
net/mlx4_en: Limit the RFS filter IDs to be < RPS_NO_FILTER
hyperv: Add error handling to rndis_filter_device_add()
hyperv: Add a check for ring_size value
ipv4: rt_cache_valid must check expired routes
net/pch_gpe: Cannot disable ethernet autonegation
qeth: repair crash in qeth_l3_vlan_rx_kill_vid()
netiucv: cleanup attribute usage
net: wiznet add missing HAS_IOMEM dependency
be2net: Missing byteswap in be_get_fw_log_level causes oops on PowerPC
mlx4: Add support for EEH error recovery
cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN
wanmain: comparing array with NULL
caif: fix NULL pointer check
...
Commit efc73f4b "net: Fix memory leak - vlan_info struct" adds deletion of
VLAN 0 for devices with feature NETIF_F_HW_VLAN_FILTER. For driver
qeth these are the layer 3 devices. Usually there exists no
separate vlan net_device for VLAN 0. Thus the qeth functions
qeth_l3_free_vlan_addresses4() and qeth_l3_free_vlan_addresses6()
require an extra checking if function __vlan_find_dev_deep()
returns with a net_device.
Cc: stable@vger.kernel.org
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the driver core handle device attribute creation and removal. This
will simplify the code and eliminates races between attribute
availability and userspace notification via uevents.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Acked-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pECD
-----END PGP SIGNATURE-----
Merge tag 'kvm-3.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"Highlights include
- full big real mode emulation on pre-Westmere Intel hosts (can be
disabled with emulate_invalid_guest_state=0)
- relatively small ppc and s390 updates
- PCID/INVPCID support in guests
- EOI avoidance; 3.6 guests should perform better on 3.6 hosts on
interrupt intensive workloads)
- Lockless write faults during live migration
- EPT accessed/dirty bits support for new Intel processors"
Fix up conflicts in:
- Documentation/virtual/kvm/api.txt:
Stupid subchapter numbering, added next to each other.
- arch/powerpc/kvm/booke_interrupts.S:
PPC asm changes clashing with the KVM fixes
- arch/s390/include/asm/sigp.h, arch/s390/kvm/sigp.c:
Duplicated commits through the kvm tree and the s390 tree, with
subsequent edits in the KVM tree.
* tag 'kvm-3.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (93 commits)
KVM: fix race with level interrupts
x86, hyper: fix build with !CONFIG_KVM_GUEST
Revert "apic: fix kvm build on UP without IOAPIC"
KVM guest: switch to apic_set_eoi_write, apic_write
apic: add apic_set_eoi_write for PV use
KVM: VMX: Implement PCID/INVPCID for guests with EPT
KVM: Add x86_hyper_kvm to complete detect_hypervisor_platform check
KVM: PPC: Critical interrupt emulation support
KVM: PPC: e500mc: Fix tlbilx emulation for 64-bit guests
KVM: PPC64: booke: Set interrupt computation mode for 64-bit host
KVM: PPC: bookehv: Add ESR flag to Data Storage Interrupt
KVM: PPC: bookehv64: Add support for std/ld emulation.
booke: Added crit/mc exception handler for e500v2
booke/bookehv: Add host crit-watchdog exception support
KVM: MMU: document mmu-lock and fast page fault
KVM: MMU: fix kvm_mmu_pagetable_walk tracepoint
KVM: MMU: trace fast page fault
KVM: MMU: fast path of handling guest page fault
KVM: MMU: introduce SPTE_MMU_WRITEABLE bit
KVM: MMU: fold tlb flush judgement into mmu_spte_update
...
Pull networking changes from David S Miller:
1) Remove the ipv4 routing cache. Now lookups go directly into the FIB
trie and use prebuilt routes cached there.
No more garbage collection, no more rDOS attacks on the routing
cache. Instead we now get predictable and consistent performance,
no matter what the pattern of traffic we service.
This has been almost 2 years in the making. Special thanks to
Julian Anastasov, Eric Dumazet, Steffen Klassert, and others who
have helped along the way.
I'm sure that with a change of this magnitude there will be some
kind of fallout, but such things ought the be simple to fix at this
point. Luckily I'm not European so I'll be around all of August to
fix things :-)
The major stages of this work here are each fronted by a forced
merge commit whose commit message contains a top-level description
of the motivations and implementation issues.
2) Pre-demux of established ipv4 TCP sockets, saves a route demux on
input.
3) TCP SYN/ACK performance tweaks from Eric Dumazet.
4) Add namespace support for netfilter L4 conntrack helpers, from Gao
Feng.
5) Add config mechanism for Energy Efficient Ethernet to ethtool, from
Yuval Mintz.
6) Remove quadratic behavior from /proc/net/unix, from Eric Dumazet.
7) Support for connection tracker helpers in userspace, from Pablo
Neira Ayuso.
8) Allow userspace driven TX load balancing functions in TEAM driver,
from Jiri Pirko.
9) Kill off NLMSG_PUT and RTA_PUT macros, more gross stuff with
embedded gotos.
10) TCP Small Queues, essentially minimize the amount of TCP data queued
up in the packet scheduler layer. Whereas the existing BQL (Byte
Queue Limits) limits the pkt_sched --> netdevice queuing levels,
this controls the TCP --> pkt_sched queueing levels.
From Eric Dumazet.
11) Reduce the number of get_page/put_page ops done on SKB fragments,
from Alexander Duyck.
12) Implement protection against blind resets in TCP (RFC 5961), from
Eric Dumazet.
13) Support the client side of TCP Fast Open, basically the ability to
send data in the SYN exchange, from Yuchung Cheng.
Basically, the sender queues up data with a sendmsg() call using
MSG_FASTOPEN, then they do the connect() which emits the queued up
fastopen data.
14) Avoid all the problems we get into in TCP when timers or PMTU events
hit a locked socket. The TCP Small Queues changes added a
tcp_release_cb() that allows us to queue work up to the
release_sock() caller, and that's what we use here too. From Eric
Dumazet.
15) Zero copy on TX support for TUN driver, from Michael S. Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1870 commits)
genetlink: define lockdep_genl_is_held() when CONFIG_LOCKDEP
r8169: revert "add byte queue limit support".
ipv4: Change rt->rt_iif encoding.
net: Make skb->skb_iif always track skb->dev
ipv4: Prepare for change of rt->rt_iif encoding.
ipv4: Remove all RTCF_DIRECTSRC handliing.
ipv4: Really ignore ICMP address requests/replies.
decnet: Don't set RTCF_DIRECTSRC.
net/ipv4/ip_vti.c: Fix __rcu warnings detected by sparse.
ipv4: Remove redundant assignment
rds: set correct msg_namelen
openvswitch: potential NULL deref in sample()
tcp: dont drop MTU reduction indications
bnx2x: Add new 57840 device IDs
tcp: avoid oops in tcp_metrics and reset tcpm_stamp
niu: Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return value
niu: Fix to check for dma mapping errors.
net: Fix references to out-of-scope variables in put_cmsg_compat()
net: ethernet: davinci_emac: add pm_runtime support
net: ethernet: davinci_emac: Remove unnecessary #include
...
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter interrupt for an APQN must be re-enabled after a reset.
This patch sends the interrupt enablement request again, if the APQN
is busy or the reset is still in progress.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Add a mechanism to wait for outstanding IO during shutdown.
Schedule the block_bh and device_bh and wait until our request queues
are empty.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
For processing under KVM it is required to detect
the actual SCLP console type in order to set it as
preferred console.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Let the driver core handle driver attribute creation and removal. This
will simplify the code and eliminates races between attribute
availability and userspace notification via uevents.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let the driver core handle device attribute creation and removal. This
will simplify the code and eliminates races between attribute
availability and userspace notification via uevents.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let the driver core handle device attribute creation and removal. This
will simplify the code and eliminates races between attribute
availability and userspace notification via uevents.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 patches from Heiko Carstens:
"A couple of s390 patches for the 3.5 merge window. Just a collection
of bug fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uaccess: fix access_ok compile warnings
s390/cmpxchg: select HAVE_CMPXCHG_LOCAL option
s390/cmpxchg: fix sign extension bugs
s390/cmpxchg: fix 1 and 2 byte memory accesses
s390/cmpxchg: fix compile warnings specific to s390
s390/cmpxchg: add missing memory barrier to cmpxchg64
s390/cpu: remove cpu "capabilities" sysfs attribute
s390/kernel: Fix smp_call_ipl_cpu() for offline CPUs
s390/kernel: Introduce memcpy_absolute() function
s390/headers: replace __s390x__ with CONFIG_64BIT where possible
s390/headers: remove #ifdef __KERNEL__ from not exported headers
s390/irq: split irq stats for cpu-measurement alert facilities
s390/kexec: Move early_pgm_check_handler() to text section
s390/kdump: Use real mode for PSW restart and kexec
s390/kdump: Account /sys/kernel/kexec_crash_size changes in OS info
s390/kernel: Remove OS info init function call and diag 308 for kdump
Pull KVM changes from Avi Kivity:
"Changes include additional instruction emulation, page-crossing MMIO,
faster dirty logging, preventing the watchdog from killing a stopped
guest, module autoload, a new MSI ABI, and some minor optimizations
and fixes. Outside x86 we have a small s390 and a very large ppc
update.
Regarding the new (for kvm) rebaseless workflow, some of the patches
that were merged before we switch trees had to be rebased, while
others are true pulls. In either case the signoffs should be correct
now."
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
arch/powerpc/kvm/book3s_segment.S and arch/x86/include/asm/kvm_para.h.
I suspect the kvm_para.h resolution ends up doing the "do I have cpuid"
check effectively twice (it was done differently in two different
commits), but better safe than sorry ;)
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (125 commits)
KVM: make asm-generic/kvm_para.h have an ifdef __KERNEL__ block
KVM: s390: onereg for timer related registers
KVM: s390: epoch difference and TOD programmable field
KVM: s390: KVM_GET/SET_ONEREG for s390
KVM: s390: add capability indicating COW support
KVM: Fix mmu_reload() clash with nested vmx event injection
KVM: MMU: Don't use RCU for lockless shadow walking
KVM: VMX: Optimize %ds, %es reload
KVM: VMX: Fix %ds/%es clobber
KVM: x86 emulator: convert bsf/bsr instructions to emulate_2op_SrcV_nobyte()
KVM: VMX: unlike vmcs on fail path
KVM: PPC: Emulator: clean up SPR reads and writes
KVM: PPC: Emulator: clean up instruction parsing
kvm/powerpc: Add new ioctl to retreive server MMU infos
kvm/book3s: Make kernel emulated H_PUT_TCE available for "PR" KVM
KVM: PPC: bookehv: Fix r8/r13 storing in level exception handler
KVM: PPC: Book3S: Enable IRQs during exit handling
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Fix stbux emulation
KVM: PPC: bookehv: Use lwz/stw instead of PPC_LL/PPC_STL for 32-bit fields
...
Replace __s390x__ with CONFIG_64BIT in all places that are not exported
to userspace or guarded with #ifdef __KERNEL__.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
Currently qemu/kvm on s390 uses a guest mapping that does not
allow the guest backing page table to be write-protected to
support older systems. On those older systems a host write
protection fault will be delivered to the guest.
Newer systems allow to write-protect the guest backing memory
and let the fault be delivered to the host, thus allowing COW.
Use a capability bit to tell qemu if that is possible.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The qeth layer3 driver is notified about IP address changes.
Changes concerning qeth driven network interfaces have to be
forwarded to the OSA-card. This includes IP addresses of VLAN
interfaces with a qeth device as base device. Function
qeth_l3_verify_vlan_dev() determines if the net_device of the
IP event belongs to a vlan device belonging to a qeth device
as real device. This function is broken starting with commit
7ff0bcf676 , which means IP
addresses of VLAN devices are no longer set at the base qeth
device. The patch repairs function qeth_l3_verify_vlan_dev().
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1abd2296b4 starts removing
token ring from qeth_l3. This patch removes the rest of token
ring related code from the driver.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl