The same code which recognizes ICMP error packets is duplicated several
times. Use the icmp_is_err() and icmpv6_is_err() helpers instead, which
do the same thing.
ip_multipath_l3_keys() and tcf_nat_act() didn't check for all the error types,
assume that they should instead.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even with icmp_errors_use_inbound_ifaddr set, traceroute returns the
primary address of the interface the packet was received on, even if
the path goes through a secondary address. In the example:
1.0.3.1/24
---- 1.0.1.3/24 1.0.1.1/24 ---- 1.0.2.1/24 1.0.2.4/24 ----
|H1|--------------------------|R1|--------------------------|H2|
---- N1 ---- N2 ----
where 1.0.3.1/24 is R1's primary address on N1, traceroute from
H1 to H2 returns:
traceroute to 1.0.2.4 (1.0.2.4), 30 hops max, 60 byte packets
1 1.0.3.1 (1.0.3.1) 0.018 ms 0.006 ms 0.006 ms
2 1.0.2.4 (1.0.2.4) 0.021 ms 0.007 ms 0.007 ms
After applying this patch, it returns:
traceroute to 1.0.2.4 (1.0.2.4), 30 hops max, 60 byte packets
1 1.0.1.1 (1.0.1.1) 0.033 ms 0.007 ms 0.006 ms
2 1.0.2.4 (1.0.2.4) 0.011 ms 0.007 ms 0.007 ms
Original-patch-by: Bill Fenner <fenner@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically linux tried to stick to RFC 791, 1122, 2003
for IPv4 ID field generation.
RFC 6864 made clear that no matter how hard we try,
we can not ensure unicity of IP ID within maximum
lifetime for all datagrams with a given source
address/destination address/protocol tuple.
Linux uses a per socket inet generator (inet_id), initialized
at connection startup with a XOR of 'jiffies' and other
fields that appear clear on the wire.
Thiemo Nagel pointed that this strategy is a privacy
concern as this provides 16 bits of entropy to fingerprint
devices.
Let's switch to a random starting point, this is just as
good as far as RFC 6864 is concerned and does not leak
anything critical.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thiemo Nagel <tnagel@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_max_syn_backlog default value depends on memory size
and TCP ehash size. Before this patch, the max value
was 2048 [1], which is considered too small nowadays.
Increase it to 4096 to match the recent SOMAXCONN change.
[1] This is with TCP ehash size being capped to 524288 buckets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Yue Cao <ycao009@ucr.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot triggered struct net NULL deref in NF_HOOK_LIST:
RIP: 0010:NF_HOOK_LIST include/linux/netfilter.h:331 [inline]
RIP: 0010:ip6_sublist_rcv+0x5c9/0x930 net/ipv6/ip6_input.c:292
ipv6_list_rcv+0x373/0x4b0 net/ipv6/ip6_input.c:328
__netif_receive_skb_list_ptype net/core/dev.c:5274 [inline]
Reason:
void ipv6_list_rcv(struct list_head *head, struct packet_type *pt,
struct net_device *orig_dev)
[..]
list_for_each_entry_safe(skb, next, head, list) {
/* iterates list */
skb = ip6_rcv_core(skb, dev, net);
/* ip6_rcv_core drops skb -> NULL is returned */
if (skb == NULL)
continue;
[..]
}
/* sublist is empty -> curr_net is NULL */
ip6_sublist_rcv(&sublist, curr_dev, curr_net);
Before the recent change NF_HOOK_LIST did a list iteration before
struct net deref, i.e. it was a no-op in the empty list case.
List iteration now happens after *net deref, causing crash.
Follow the same pattern as the ip(v6)_list_rcv loop and add a list_empty
test for the final sublist dispatch too.
Cc: Edward Cree <ecree@solarflare.com>
Reported-by: syzbot+c54f457cad330e57e967@syzkaller.appspotmail.com
Fixes: ca58fbe06c ("netfilter: add and use nf_hook_slow_list()")
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for !md doens't really work for ip_tunnel_info_opts(info) which
only does info + 1. Also to avoid out-of-bounds access on info, it should
ensure options_len is not less than erspan_metadata in both erspan_xmit()
and ip6erspan_tunnel_xmit().
Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KCSAN reported a data-race in udp_set_dev_scratch() [1]
The issue here is that we must not write over skb fields
if skb is shared. A similar issue has been fixed in commit
89c22d8c3b ("net: Fix skb csum races when peeking")
While we are at it, use a helper only dealing with
udp_skb_scratch(skb)->csum_unnecessary, as this allows
udp_set_dev_scratch() to be called once and thus inlined.
[1]
BUG: KCSAN: data-race in udp_set_dev_scratch / udpv6_recvmsg
write to 0xffff888120278317 of 1 bytes by task 10411 on cpu 1:
udp_set_dev_scratch+0xea/0x200 net/ipv4/udp.c:1308
__first_packet_length+0x147/0x420 net/ipv4/udp.c:1556
first_packet_length+0x68/0x2a0 net/ipv4/udp.c:1579
udp_poll+0xea/0x110 net/ipv4/udp.c:2720
sock_poll+0xed/0x250 net/socket.c:1256
vfs_poll include/linux/poll.h:90 [inline]
do_select+0x7d0/0x1020 fs/select.c:534
core_sys_select+0x381/0x550 fs/select.c:677
do_pselect.constprop.0+0x11d/0x160 fs/select.c:759
__do_sys_pselect6 fs/select.c:784 [inline]
__se_sys_pselect6 fs/select.c:769 [inline]
__x64_sys_pselect6+0x12e/0x170 fs/select.c:769
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff888120278317 of 1 bytes by task 10413 on cpu 0:
udp_skb_csum_unnecessary include/net/udp.h:358 [inline]
udpv6_recvmsg+0x43e/0xe90 net/ipv6/udp.c:310
inet6_recvmsg+0xbb/0x240 net/ipv6/af_inet6.c:592
sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 10413 Comm: syz-executor.0 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 2276f58ac5 ("udp: use a separate rx queue for packet reception")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Busy polling usually runs without locks.
Let's use skb_queue_empty_lockless() instead of skb_queue_empty()
Also uses READ_ONCE() in __skb_try_recv_datagram() to address
a similar potential problem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many poll() handlers are lockless. Using skb_queue_empty_lockless()
instead of skb_queue_empty() is more appropriate.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit af4d768ad2 ("net/ipv4: Add support for specifying metric
of connected routes"), when updating an IP address with a different metric,
the associated connected route is updated, too.
Still, the mentioned commit doesn't handle properly some corner cases:
$ ip addr add dev eth0 192.168.1.0/24
$ ip addr add dev eth0 192.168.2.1/32 peer 192.168.2.2
$ ip addr add dev eth0 192.168.3.1/24
$ ip addr change dev eth0 192.168.1.0/24 metric 10
$ ip addr change dev eth0 192.168.2.1/32 peer 192.168.2.2 metric 10
$ ip addr change dev eth0 192.168.3.1/24 metric 10
$ ip -4 route
192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.0
192.168.2.2 dev eth0 proto kernel scope link src 192.168.2.1
192.168.3.0/24 dev eth0 proto kernel scope link src 192.168.2.1 metric 10
Only the last route is correctly updated.
The problem is the current test in fib_modify_prefix_metric():
if (!(dev->flags & IFF_UP) ||
ifa->ifa_flags & (IFA_F_SECONDARY | IFA_F_NOPREFIXROUTE) ||
ipv4_is_zeronet(prefix) ||
prefix == ifa->ifa_local || ifa->ifa_prefixlen == 32)
Which should be the logical 'not' of the pre-existing test in
fib_add_ifaddr():
if (!ipv4_is_zeronet(prefix) && !(ifa->ifa_flags & IFA_F_SECONDARY) &&
(prefix != addr || ifa->ifa_prefixlen < 32))
To properly negate the original expression, we need to change the last
logical 'or' to a logical 'and'.
Fixes: af4d768ad2 ("net/ipv4: Add support for specifying metric of connected routes")
Reported-and-suggested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCPI_OPT_SYN_DATA bit as part of tcpi_options currently reports whether
or not data-in-SYN was ack'd on both the client and server side. We'd like
to gather more information on the client-side in the failure case in order
to indicate the reason for the failure. This can be useful for not only
debugging TFO, but also for creating TFO socket policies. For example, if
a middle box removes the TFO option or drops a data-in-SYN, we can
can detect this case, and turn off TFO for these connections saving the
extra retransmits.
The newly added tcpi_fastopen_client_fail status is 2 bits and has the
following 4 states:
1) TFO_STATUS_UNSPEC
Catch-all state which includes when TFO is disabled via black hole
detection, which is indicated via LINUX_MIB_TCPFASTOPENBLACKHOLE.
2) TFO_COOKIE_UNAVAILABLE
If TFO_CLIENT_NO_COOKIE mode is off, this state indicates that no cookie
is available in the cache.
3) TFO_DATA_NOT_ACKED
Data was sent with SYN, we received a SYN/ACK but it did not cover the data
portion. Cookie is not accepted by server because the cookie may be invalid
or the server may be overloaded.
4) TFO_SYN_RETRANSMITTED
Data was sent with SYN, we received a SYN/ACK which did not cover the data
after at least 1 additional SYN was sent (without data). It may be the case
that a middle-box is dropping data-in-SYN packets. Thus, it would be more
efficient to not use TFO on this connection to avoid extra retransmits
during connection establishment.
These new fields do not cover all the cases where TFO may fail, but other
failures, such as SYN/ACK + data being dropped, will result in the
connection not becoming established. And a connection blackhole after
session establishment shows up as a stalled connection.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the iph field from the state structure, which is not
properly initialized. Instead, add a new field to make the "do we want
to set DF" be the state bit and move the code to set the DF flag from
ip_frag_next().
Joint work with Pablo and Linus.
Fixes: 19c3401a91 ("net: ipv4: place control buffer handling away from fragmentation iterators")
Reported-by: Patrick Schönthaler <patrick@notvads.ovh>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas found that some forwarded packets would be stuck
in FQ packet scheduler because their skb->tstamp contained
timestamps far in the future.
We thought we addressed this point in commit 8203e2d844
("net: clear skb->tstamp in forwarding paths") but there
is still an issue when/if a packet needs to be fragmented.
In order to meet EDT requirements, we have to make sure all
fragments get the original skb->tstamp.
Note that this original skb->tstamp should be zero in
forwarding path, but might have a non zero value in
output path if user decided so.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thomas Bartschies <Thomas.Bartschies@cvk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse and Ido reported the following race condition:
<CPU A, t0> - Received packet A is forwarded and cached dst entry is
taken from the nexthop ('nhc->nhc_rth_input'). Calls skb_dst_set()
<t1> - Given Jesse has busy routers ("ingesting full BGP routing tables
from multiple ISPs"), route is added / deleted and rt_cache_flush() is
called
<CPU B, t2> - Received packet B tries to use the same cached dst entry
from t0, but rt_cache_valid() is no longer true and it is replaced in
rt_cache_route() by the newer one. This calls dst_dev_put() on the
original dst entry which assigns the blackhole netdev to 'dst->dev'
<CPU A, t3> - dst_input(skb) is called on packet A and it is dropped due
to 'dst->dev' being the blackhole netdev
There are 2 issues in the v4 routing code:
1. A per-netns counter is used to do the validation of the route. That
means whenever a route is changed in the netns, users of all routes in
the netns needs to redo lookup. v6 has an implementation of only
updating fn_sernum for routes that are affected.
2. When rt_cache_valid() returns false, rt_cache_route() is called to
throw away the current cache, and create a new one. This seems
unnecessary because as long as this route does not change, the route
cache does not need to be recreated.
To fully solve the above 2 issues, it probably needs quite some code
changes and requires careful testing, and does not suite for net branch.
So this patch only tries to add the deleted cached rt into the uncached
list, so user could still be able to use it to receive packets until
it's done.
Fixes: 95c47f9cf5 ("ipv4: call dst_dev_put() properly")
Signed-off-by: Wei Wang <weiwan@google.com>
Reported-by: Ido Schimmel <idosch@idosch.org>
Reported-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Tested-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
...instead of -EINVAL. An issue was found with older kernel versions
while unplugging a NFS client with pending RPCs, and the wrong error
code here prevented it from recovering once link is back up with a
configured address.
Incidentally, this is not an issue anymore since commit 4f8943f808
("SUNRPC: Replace direct task wakeups from softirq context"), included
in 5.2-rc7, had the effect of decoupling the forwarding of this error
by using SO_ERROR in xs_wake_error(), as pointed out by Benjamin
Coddington.
To the best of my knowledge, this isn't currently causing any further
issue, but the error code doesn't look appropriate anyway, and we
might hit this in other paths as well.
In detail, as analysed by Gonzalo Siero, once the route is deleted
because the interface is down, and can't be resolved and we return
-EINVAL here, this ends up, courtesy of inet_sk_rebuild_header(),
as the socket error seen by tcp_write_err(), called by
tcp_retransmit_timer().
In turn, tcp_write_err() indirectly calls xs_error_report(), which
wakes up the RPC pending tasks with a status of -EINVAL. This is then
seen by call_status() in the SUN RPC implementation, which aborts the
RPC call calling rpc_exit(), instead of handling this as a
potentially temporary condition, i.e. as a timeout.
Return -EINVAL only if the input parameters passed to
ip_route_output_key_hash_rcu() are actually invalid (this is the case
if the specified source address is multicast, limited broadcast or
all zeroes), but return -ENETUNREACH in all cases where, at the given
moment, the given source address doesn't allow resolving the route.
While at it, drop the initialisation of err to -ENETUNREACH, which
was added to __ip_route_output_key() back then by commit
0315e38270 ("net: Fix behaviour of unreachable, blackhole and
prohibit routes"), but actually had no effect, as it was, and is,
overwritten by the fib_lookup() return code assignment, and anyway
ignored in all other branches, including the if (fl4->saddr) one:
I find this rather confusing, as it would look like -ENETUNREACH is
the "default" error, while that statement has no effect.
Also note that after commit fc75fc8339 ("ipv4: dont create routes
on down devices"), we would get -ENETUNREACH if the device is down,
but -EINVAL if the source address is specified and we can't resolve
the route, and this appears to be rather inconsistent.
Reported-by: Stefan Walter <walteste@inf.ethz.ch>
Analysed-by: Benjamin Coddington <bcodding@redhat.com>
Analysed-by: Gonzalo Siero <gsierohu@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot found that if __inet_inherit_port() returns an error,
we call tcp_done() after inet_csk_prepare_forced_close(),
meaning the socket lock is no longer held.
We might fix this in a different way in net-next, but
for 5.4 it seems safer to relax the lockdep check.
Fixes: d983ea6f16 ("tcp: add rcu protection around tp->fastopen_rsk")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_zerocopy_receive() rounds down the zc->length a multiple of
PAGE_SIZE. This results in two issues:
- tcp_zerocopy_receive sets recv_skip_hint to the length of the
receive queue if the zc->length input is smaller than the
PAGE_SIZE, even though the data in receive queue could be
zerocopied.
- tcp_zerocopy_receive would set recv_skip_hint of 0, in cases
where we have a little bit of data after the perfectly-sized
packets.
To fix these issues, do not store the rounded down value in
zc->length. Round down the length passed to zap_page_range(),
and return min(inq, zc->length) when the zap_range is 0.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_wmem_queued while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
sk_wmem_queued_add() helper is added so that we can in
the future convert to ADD_ONCE() or equivalent if/when
available.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_sndbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_rcvbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There two places where we fetch tp->urg_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write side use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->snd_nxt while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->write_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->copied_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Note that tcp_inq_hint() was already using READ_ONCE(tp->copied_seq)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->rcv_nxt while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Note that tcp_inq_hint() was already using READ_ONCE(tp->rcv_nxt)
syzbot reported :
BUG: KCSAN: data-race in tcp_poll / tcp_queue_rcv
write to 0xffff888120425770 of 4 bytes by interrupt on cpu 0:
tcp_rcv_nxt_update net/ipv4/tcp_input.c:3365 [inline]
tcp_queue_rcv+0x180/0x380 net/ipv4/tcp_input.c:4638
tcp_rcv_established+0xbf1/0xf50 net/ipv4/tcp_input.c:5616
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
tcp_v4_rcv+0x1a03/0x1bf0 net/ipv4/tcp_ipv4.c:1923
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
read to 0xffff888120425770 of 4 bytes by task 7254 on cpu 1:
tcp_stream_is_readable net/ipv4/tcp.c:480 [inline]
tcp_poll+0x204/0x6b0 net/ipv4/tcp.c:554
sock_poll+0xed/0x250 net/socket.c:1256
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll.isra.0+0x90/0x190 fs/eventpoll.c:892
ep_send_events_proc+0x113/0x5c0 fs/eventpoll.c:1749
ep_scan_ready_list.constprop.0+0x189/0x500 fs/eventpoll.c:704
ep_send_events fs/eventpoll.c:1793 [inline]
ep_poll+0xe3/0x900 fs/eventpoll.c:1930
do_epoll_wait+0x162/0x180 fs/eventpoll.c:2294
__do_sys_epoll_pwait fs/eventpoll.c:2325 [inline]
__se_sys_epoll_pwait fs/eventpoll.c:2311 [inline]
__x64_sys_epoll_pwait+0xcd/0x170 fs/eventpoll.c:2311
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7254 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tcp_v4_err() and tcp_v6_err() do the following operations
while they do not own the socket lock :
fastopen = tp->fastopen_rsk;
snd_una = fastopen ? tcp_rsk(fastopen)->snt_isn : tp->snd_una;
The problem is that without appropriate barrier, the compiler
might reload tp->fastopen_rsk and trigger a NULL deref.
request sockets are protected by RCU, we can simply add
the missing annotations and barriers to solve the issue.
Fixes: 168a8f5805 ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_rcvlowat() or int_sk_rcvlowat() might be called without the socket
lock for example from tcp_poll().
Use READ_ONCE() to document the fact that other cpus might change
sk->sk_rcvlowat under us and avoid KCSAN splats.
Use WRITE_ONCE() on write sides too.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
sk_add_backlog() callers usually read sk->sk_rcvbuf without
owning the socket lock. This means sk_rcvbuf value can
be changed by other cpus, and KCSAN complains.
Add READ_ONCE() annotations to document the lockless nature
of these reads.
Note that writes over sk_rcvbuf should also use WRITE_ONCE(),
but this will be done in separate patches to ease stable
backports (if we decide this is relevant for stable trees).
BUG: KCSAN: data-race in tcp_add_backlog / tcp_recvmsg
write to 0xffff88812ab369f8 of 8 bytes by interrupt on cpu 1:
__sk_add_backlog include/net/sock.h:902 [inline]
sk_add_backlog include/net/sock.h:933 [inline]
tcp_add_backlog+0x45a/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812ab369f8 of 8 bytes by task 7271 on cpu 0:
tcp_recvmsg+0x470/0x1a30 net/ipv4/tcp.c:2047
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7271 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
tcp_memory_pressure is read without holding any lock,
and its value could be changed on other cpus.
Use READ_ONCE() to annotate these lockless reads.
The write side is already using atomic ops.
Fixes: b8da51ebb1 ("tcp: introduce tcp_under_memory_pressure()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
reqsk_queue_empty() is called from inet_csk_listen_poll() while
other cpus might write ->rskq_accept_head value.
Use {READ|WRITE}_ONCE() to avoid compiler tricks
and potential KCSAN splats.
Fixes: fff1f3001c ("tcp: add a spinlock to protect struct request_sock_queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If IPsec is not configured, there is no reason to delay the inevitable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Since commit c09551c6ff ("net: ipv4: use a dedicated counter
for icmp_v4 redirect packets") we use 'n_redirects' to account
for redirect packets, but we still use 'rate_tokens' to compute
the redirect packets exponential backoff.
If the device sent to the relevant peer any ICMP error packet
after sending a redirect, it will also update 'rate_token' according
to the leaking bucket schema; typically 'rate_token' will raise
above BITS_PER_LONG and the redirect packets backoff algorithm
will produce undefined behavior.
Fix the issue using 'n_redirects' to compute the exponential backoff
in ip_rt_send_redirect().
Note that we still clear rate_tokens after a redirect silence period,
to avoid changing an established behaviour.
The root cause predates git history; before the mentioned commit in
the critical scenario, the kernel stopped sending redirects, after
the mentioned commit the behavior more randomic.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: c09551c6ff ("net: ipv4: use a dedicated counter for icmp_v4 redirect packets")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is only used via function pointer.
"inline" doesn't hurt given that taking address of an inline function
forces out-of-line version but it doesn't help either.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since errors are propagated all the way up to the caller, propagate
possible extack of the caller all the way down to the notifier block
callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike events for registered notifier, during the registration, the
errors that happened for the block being registered are not propagated
up to the caller. Make sure the error is propagated for FIB rules and
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all users of FIB notifier only cares about events in init_net.
Later in this patchset, users get interested in other namespaces too.
However, for every registered block user is interested only about one
namespace. Make the FIB notifier registration per-netns and avoid
unnecessary calls of notifier block for other namespaces.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently a refactoring patch brought a bug, that was caught
by syzbot [1]
Original code was correct, do not try to be smarter than the
compiler :/
[1]
BUG: KASAN: slab-out-of-bounds in tcp_zerocopy_receive net/ipv4/tcp.c:1807 [inline]
BUG: KASAN: slab-out-of-bounds in do_tcp_getsockopt.isra.0+0x2c6c/0x3120 net/ipv4/tcp.c:3654
Read of size 4 at addr ffff8880943cf188 by task syz-executor.2/17508
CPU: 0 PID: 17508 Comm: syz-executor.2 Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0xd4/0x306 mm/kasan/report.c:351
__kasan_report.cold+0x1b/0x36 mm/kasan/report.c:482
kasan_report+0x12/0x17 mm/kasan/common.c:618
__asan_report_load4_noabort+0x14/0x20 mm/kasan/generic_report.c:131
tcp_zerocopy_receive net/ipv4/tcp.c:1807 [inline]
do_tcp_getsockopt.isra.0+0x2c6c/0x3120 net/ipv4/tcp.c:3654
tcp_getsockopt+0xbf/0xe0 net/ipv4/tcp.c:3680
sock_common_getsockopt+0x94/0xd0 net/core/sock.c:3098
__sys_getsockopt+0x16d/0x310 net/socket.c:2129
__do_sys_getsockopt net/socket.c:2144 [inline]
__se_sys_getsockopt net/socket.c:2141 [inline]
__x64_sys_getsockopt+0xbe/0x150 net/socket.c:2141
do_syscall_64+0xfd/0x6a0 arch/x86/entry/common.c:296
Fixes: d8e18a516f ("net: Use skb accessors in network core")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change an application sending <= 1MSS worth of data and
enabling UDP GSO would fail if the system had SW GSO enabled, but the
same send would succeed if HW GSO offload is enabled. In addition to this
inconsistency the error in the SW GSO case does not get back to the
application if sending out of a real device so the user is unaware of this
failure.
With this change we only perform GSO if the # of segments is > 1 even
if the application has enabled segmentation. I've also updated the
relevant udpgso selftests.
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Signed-off-by: Josh Hunt <johunt@akamai.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dfec0ee22c ("udp: Record gso_segs when supporting UDP segmentation offload")
added gso_segs calculation, but incorrectly got sizeof() the pointer and
not the underlying data type. In addition let's fix the v6 case.
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Fixes: dfec0ee22c ("udp: Record gso_segs when supporting UDP segmentation offload")
Signed-off-by: Josh Hunt <johunt@akamai.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Remove the skb_ext_del from nf_reset, and renames it to a more
fitting nf_reset_ct(). Patch from Florian Westphal.
2) Fix deadlock in nft_connlimit between packet path updates and
the garbage collector.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The experimental root file system support in cifs.ko relies on
ipconfig to set up the network stack and then accessing the SMB share
that contains the rootfs files.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit exposed an old retransmits_timed_out() bug
which assumed it could call tcp_model_timeout() with
TCP_RTO_MIN as rto_base for all states.
But flows in SYN_SENT or SYN_RECV state uses a different
RTO base (1 sec instead of 200 ms, unless BPF choses
another value)
This caused a reduction of SYN retransmits from 6 to 4 with
the default /proc/sys/net/ipv4/tcp_syn_retries value.
Fixes: a41e8a88b0 ("tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_twsk_unique() has a hard coded assumption about ipv4 loopback
being 127/8
Lets instead use the standard ipv4_is_loopback() method,
in a new ipv6_addr_v4mapped_loopback() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 174e23810c
("sk_buff: drop all skb extensions on free and skb scrubbing") made napi
recycle always drop skb extensions. The additional skb_ext_del() that is
performed via nf_reset on napi skb recycle is not needed anymore.
Most nf_reset() calls in the stack are there so queued skb won't block
'rmmod nf_conntrack' indefinitely.
This removes the skb_ext_del from nf_reset, and renames it to a more
fitting nf_reset_ct().
In a few selected places, add a call to skb_ext_reset to make sure that
no active extensions remain.
I am submitting this for "net", because we're still early in the release
cycle. The patch applies to net-next too, but I think the rename causes
needless divergence between those trees.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
erspan driver calls ether_setup(), after commit 61e84623ac
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the erspan device to not be greater
than 1500, this limit value is not correct for ipgre tap device.
Tested:
Before patch:
# ip link set erspan0 mtu 1600
Error: mtu greater than device maximum.
After patch:
# ip link set erspan0 mtu 1600
# ip -d link show erspan0
21: erspan0@NONE: <BROADCAST,MULTICAST> mtu 1600 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 0
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng and Marek Majkowski independently reported a weird
behavior of TCP_USER_TIMEOUT option when used at connect() time.
When the TCP_USER_TIMEOUT is reached, tcp_write_timeout()
believes the flow should live, and the following condition
in tcp_clamp_rto_to_user_timeout() programs one jiffie timers :
remaining = icsk->icsk_user_timeout - elapsed;
if (remaining <= 0)
return 1; /* user timeout has passed; fire ASAP */
This silly situation ends when the max syn rtx count is reached.
This patch makes sure we honor both TCP_SYNCNT and TCP_USER_TIMEOUT,
avoiding these spurious SYN packets.
Fixes: b701a99e43 ("tcp: Add tcp_clamp_rto_to_user_timeout() helper to improve accuracy")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Reported-by: Marek Majkowski <marek@cloudflare.com>
Cc: Jon Maxwell <jmaxwell37@gmail.com>
Link: https://marc.info/?l=linux-netdev&m=156940118307949&w=2
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Tested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Marek Majkowski <marek@cloudflare.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug in the previous logic that attempted to ensure gain cycling
gets inflight above BDP even for small BDPs. This code correctly raised and
lowered target inflight values during the gain cycle. And this code
correctly ensured that cwnd was raised when probing bandwidth. However, it
did not correspondingly ensure that cwnd was *not* raised in this way when
*not* probing for bandwidth. The result was that small-BDP flows that were
always cwnd-bound could go for many cycles with a fixed cwnd, and not probe
or yield bandwidth at all. This meant that multiple small-BDP flows could
fail to converge in their bandwidth allocations.
Fixes: 3c346b233c68 ("tcp_bbr: fix bw probing to raise in-flight data for very small BDPs")
Signed-off-by: Kevin(Yudong) Yang <yyd@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ctl packets sent on behalf of TIME_WAIT sockets currently
have a zero skb->priority, which can cause various problems.
In this patch we :
- add a tw_priority field in struct inet_timewait_sock.
- populate it from sk->sk_priority when a TIME_WAIT is created.
- For IPv4, change ip_send_unicast_reply() and its two
callers to propagate tw_priority correctly.
ip_send_unicast_reply() no longer changes sk->sk_priority.
- For IPv6, make sure TIME_WAIT sockets pass their tw_priority
field to tcp_v6_send_response() and tcp_v6_send_ack().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian noted that rt_uses_gateway has a more subtle use than 'is gateway
set':
https://lore.kernel.org/netdev/alpine.LFD.2.21.1909151104060.2546@ja.home.ssi.bg/
Revert that part of the commit referenced in the Fixes tag.
Currently, there are no u8 holes in 'struct rtable'. There is a 4-byte hole
in the second cacheline which contains the gateway declaration. So move
rt_gw_family down to the gateway declarations since they are always used
together, and then re-use that u8 for rt_uses_gateway. End result is that
rtable size is unchanged.
Fixes: 1550c17193 ("ipv4: Prepare rtable for IPv6 gateway")
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
Pull RCU updates from Ingo Molnar:
"This cycle's RCU changes were:
- A few more RCU flavor consolidation cleanups.
- Updates to RCU's list-traversal macros improving lockdep usability.
- Forward-progress improvements for no-CBs CPUs: Avoid ignoring
incoming callbacks during grace-period waits.
- Forward-progress improvements for no-CBs CPUs: Use ->cblist
structure to take advantage of others' grace periods.
- Also added a small commit that avoids needlessly inflicting
scheduler-clock ticks on callback-offloaded CPUs.
- Forward-progress improvements for no-CBs CPUs: Reduce contention on
->nocb_lock guarding ->cblist.
- Forward-progress improvements for no-CBs CPUs: Add ->nocb_bypass
list to further reduce contention on ->nocb_lock guarding ->cblist.
- Miscellaneous fixes.
- Torture-test updates.
- minor LKMM updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (86 commits)
MAINTAINERS: Update from paulmck@linux.ibm.com to paulmck@kernel.org
rcu: Don't include <linux/ktime.h> in rcutiny.h
rcu: Allow rcu_do_batch() to dynamically adjust batch sizes
rcu/nocb: Don't wake no-CBs GP kthread if timer posted under overload
rcu/nocb: Reduce __call_rcu_nocb_wake() leaf rcu_node ->lock contention
rcu/nocb: Reduce nocb_cb_wait() leaf rcu_node ->lock contention
rcu/nocb: Advance CBs after merge in rcutree_migrate_callbacks()
rcu/nocb: Avoid synchronous wakeup in __call_rcu_nocb_wake()
rcu/nocb: Print no-CBs diagnostics when rcutorture writer unduly delayed
rcu/nocb: EXP Check use and usefulness of ->nocb_lock_contended
rcu/nocb: Add bypass callback queueing
rcu/nocb: Atomic ->len field in rcu_segcblist structure
rcu/nocb: Unconditionally advance and wake for excessive CBs
rcu/nocb: Reduce ->nocb_lock contention with separate ->nocb_gp_lock
rcu/nocb: Reduce contention at no-CBs invocation-done time
rcu/nocb: Reduce contention at no-CBs registry-time CB advancement
rcu/nocb: Round down for number of no-CBs grace-period kthreads
rcu/nocb: Avoid ->nocb_lock capture by corresponding CPU
rcu/nocb: Avoid needless wakeups of no-CBs grace-period kthread
rcu/nocb: Make __call_rcu_nocb_wake() safe for many callbacks
...
Neal Cardwell mentioned that snd_wnd would be useful for diagnosing TCP
performance problems --
> (1) Usually when we're diagnosing TCP performance problems, we do so
> from the sender, since the sender makes most of the
> performance-critical decisions (cwnd, pacing, TSO size, TSQ, etc).
> From the sender-side the thing that would be most useful is to see
> tp->snd_wnd, the receive window that the receiver has advertised to
> the sender.
This serves the purpose of adding an additional __u32 to avoid the
would-be hole caused by the addition of the tcpi_rcvi_ooopack field.
Signed-off-by: Thomas Higdon <tph@fb.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For receive-heavy cases on the server-side, we want to track the
connection quality for individual client IPs. This counter, similar to
the existing system-wide TCPOFOQueue counter in /proc/net/netstat,
tracks out-of-order packet reception. By providing this counter in
TCP_INFO, it will allow understanding to what degree receive-heavy
sockets are experiencing out-of-order delivery and packet drops
indicating congestion.
Please note that this is similar to the counter in NetBSD TCP_INFO, and
has the same name.
Also note that we avoid increasing the size of the tcp_sock struct by
taking advantage of a hole.
Signed-off-by: Thomas Higdon <tph@fb.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP reuseport groups can hold a mix unconnected and connected sockets.
Ensure that connections only receive all traffic to their 4-tuple.
Fast reuseport returns on the first reuseport match on the assumption
that all matches are equal. Only if connections are present, return to
the previous behavior of scoring all sockets.
Record if connections are present and if so (1) treat such connected
sockets as an independent match from the group, (2) only return
2-tuple matches from reuseport and (3) do not return on the first
2-tuple reuseport match to allow for a higher scoring match later.
New field has_conns is set without locks. No other fields in the
bitmap are modified at runtime and the field is only ever set
unconditionally, so an RMW cannot miss a change.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Link: http://lkml.kernel.org/r/CA+FuTSfRP09aJNYRt04SS6qj22ViiOEWaWmLAwX0psk8-PGNxw@mail.gmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting skb->mark for UDP and RAW sockets using cmsg.
This is analogous to existing support for TOS, TTL, txtime, etc.
Packet sockets already support this as of commit c7d39e3263
("packet: support per-packet fwmark for af_packet sendmsg").
Similar to other fields, implement by
1. initialize the sockcm_cookie.mark from socket option sk_mark
2. optionally overwrite this in ip_cmsg_send/ip6_datagram_send_ctl
3. initialize inet_cork.mark from sockcm_cookie.mark
4. initialize each (usually just one) skb->mark from inet_cork.mark
Step 1 is handled in one location for most protocols by ipcm_init_sk
as of commit 351782067b ("ipv4: ipcm_cookie initializers").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Fix error path of nf_tables_updobj(), from Dan Carpenter.
2) Move large structure away from stack in the nf_tables offload
infrastructure, from Arnd Bergmann.
3) Move indirect flow_block logic to nf_tables_offload.
4) Support for synproxy objects, from Fernando Fernandez Mancera.
5) Support for fwd and dup offload.
6) Add __nft_offload_get_chain() helper, this implicitly fixes missing
mutex and check for offload flags in the indirect block support,
patch from wenxu.
7) Remove rules on device unregistration, from wenxu. This includes
two preparation patches to reuse nft_flow_offload_chain() and
nft_flow_offload_rule().
Large batch from Jeremy Sowden to make a second pass to the
CONFIG_HEADER_TEST support and a bit of housekeeping:
8) Missing include guard in conntrack label header, from Jeremy Sowden.
9) A few coding style errors: trailing whitespace, incorrect indent in
Kconfig, and semicolons at the end of function definitions.
10) Remove unused ipt_init() and ip6t_init() declarations.
11) Inline xt_hashlimit, ebt_802_3 and xt_physdev headers. They are
only used once.
12) Update include directive in several netfilter files.
13) Remove unused include/net/netfilter/ipv6/nf_conntrack_icmpv6.h.
14) Move nf_ip6_ext_hdr() to include/linux/netfilter_ipv6.h
15) Move several synproxy structure definitions to nf_synproxy.h
16) Move nf_bridge_frag_data structure to include/linux/netfilter_bridge.h
17) Clean up static inline definitions in nf_conntrack_ecache.h.
18) Replace defined(CONFIG...) || defined(CONFIG...MODULE) with IS_ENABLED(CONFIG...).
19) Missing inline function conditional definitions based on Kconfig
preferences in synproxy and nf_conntrack_timeout.
20) Update br_nf_pre_routing_ipv6() definition.
21) Move conntrack code in linux/skbuff.h to nf_conntrack headers.
22) Several patches to remove superfluous CONFIG_NETFILTER and
CONFIG_NF_CONNTRACK checks in headers, coming from the initial batch
support for CONFIG_HEADER_TEST for netfilter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Several header-files, Kconfig files and Makefiles have trailing
white-space. Remove it.
In netfilter/Kconfig, indent the type of CONFIG_NETFILTER_NETLINK_ACCT
correctly.
There are semicolons at the end of two function definitions in
include/net/netfilter/nf_conntrack_acct.h and
include/net/netfilter/nf_conntrack_ecache.h. Remove them.
Fix indentation in nf_conntrack_l4proto.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When tcp sends a TSO packet, adding a PSH flag on it
reduces the sojourn time of GRO packet in GRO receivers.
This is particularly the case under pressure, since RX queues
receive packets for many concurrent flows.
A sender can give a hint to GRO engines when it is
appropriate to flush a super-packet, especially when pacing
is in the picture, since next packet is probably delayed by
one ms.
Having less packets in GRO engine reduces chance
of LRU eviction or inflated RTT, and reduces GRO cost.
We found recently that we must not set the PSH flag on
individual full-size MSS segments [1] :
Under pressure (CWR state), we better let the packet sit
for a small delay (depending on NAPI logic) so that the
ACK packet is delayed, and thus next packet we send is
also delayed a bit. Eventually the bottleneck queue can
be drained. DCTCP flows with CWND=1 have demonstrated
the issue.
This patch allows to slowdown the aggregate traffic without
involving high resolution timers on senders and/or
receivers.
It has been used at Google for about four years,
and has been discussed at various networking conferences.
[1] segments smaller than MSS already have PSH flag set
by tcp_sendmsg() / tcp_mark_push(), unless MSG_MORE
has been requested by the user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix tcp_ecn_withdraw_cwr() to clear the correct bit:
TCP_ECN_QUEUE_CWR.
Rationale: basically, TCP_ECN_DEMAND_CWR is a bit that is purely about
the behavior of data receivers, and deciding whether to reflect
incoming IP ECN CE marks as outgoing TCP th->ece marks. The
TCP_ECN_QUEUE_CWR bit is purely about the behavior of data senders,
and deciding whether to send CWR. The tcp_ecn_withdraw_cwr() function
is only called from tcp_undo_cwnd_reduction() by data senders during
an undo, so it should zero the sender-side state,
TCP_ECN_QUEUE_CWR. It does not make sense to stop the reflection of
incoming CE bits on incoming data packets just because outgoing
packets were spuriously retransmitted.
The bug has been reproduced with packetdrill to manifest in a scenario
with RFC3168 ECN, with an incoming data packet with CE bit set and
carrying a TCP timestamp value that causes cwnd undo. Before this fix,
the IP CE bit was ignored and not reflected in the TCP ECE header bit,
and sender sent a TCP CWR ('W') bit on the next outgoing data packet,
even though the cwnd reduction had been undone. After this fix, the
sender properly reflects the CE bit and does not set the W bit.
Note: the bug actually predates 2005 git history; this Fixes footer is
chosen to be the oldest SHA1 I have tested (from Sep 2007) for which
the patch applies cleanly (since before this commit the code was in a
.h file).
Fixes: bdf1ee5d3b ("[TCP]: Move code from tcp_ecn.h to tcp*.c and tcp.h & remove it")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a re-post of previous patch wrote by David Miller[1].
Phil Karn reported[2] that on busy networks with lots of unresolved
multicast routing entries, the creation of new multicast group routes
can be extremely slow and unreliable.
The reason is we hard-coded multicast route entries with unresolved source
addresses(cache_resolve_queue_len) to 10. If some multicast route never
resolves and the unresolved source addresses increased, there will
be no ability to create new multicast route cache.
To resolve this issue, we need either add a sysctl entry to make the
cache_resolve_queue_len configurable, or just remove cache_resolve_queue_len
limit directly, as we already have the socket receive queue limits of mrouted
socket, pointed by David.
>From my side, I'd perfer to remove the cache_resolve_queue_len limit instead
of creating two more(IPv4 and IPv6 version) sysctl entry.
[1] https://lkml.org/lkml/2018/7/22/11
[2] https://lkml.org/lkml/2018/7/21/343
v3: instead of remove cache_resolve_queue_len totally, let's only remove
the hard code limit when allocate the unresolved cache, as Eric Dumazet
suggested, so we don't need to re-count it in other places.
v2: hold the mfc_unres_lock while walking the unresolved list in
queue_count(), as Nikolay Aleksandrov remind.
Reported-by: Phil Karn <karn@ka9q.net>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_diag_get_aux_size() can be called with sockets in any state.
icsk_ulp_ops is only present for full sockets.
For SYN_RECV or TIME_WAIT ones we would access garbage.
Fixes: 61723b3932 ("tcp: ulp: add functions to dump ulp-specific information")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Luke Hsiao <lukehsiao@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Cc: Davide Caratti <dcaratti@redhat.com>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a v4 route that uses a v6 nexthop from a nexthop group.
Allow the kernel to properly send the nexthop as v6 via the RTA_VIA
attribute.
Broken behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via 254.128.0.0 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
Fixed behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via inet6 fe80::9 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
v2, v3: Addresses code review comments from David Ahern
Fixes: dcb1ecb50e (“ipv4: Prepare for fib6_nh from a nexthop object”)
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
currently, only getsockopt(TCP_ULP) can be invoked to know if a ULP is on
top of a TCP socket. Extend idiag_get_aux() and idiag_get_aux_size(),
introduced by commit b37e88407c ("inet_diag: allow protocols to provide
additional data"), to report the ULP name and other information that can
be made available by the ULP through optional functions.
Users having CAP_NET_ADMIN privileges will then be able to retrieve this
information through inet_diag_handler, if they specify INET_DIAG_INFO in
the request.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This explicitly clarifies that bbr_bdp() returns the rounded-up value of
the bandwidth-delay product and why in the comments.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP associates tx timestamp requests with a byte in the bytestream.
If merging skbs in tcp_mtu_probe, migrate the tstamp request.
Similar to MSG_EOR, do not allow moving a timestamp from any segment
in the probe but the last. This to avoid merging multiple timestamps.
Tested with the packetdrill script at
https://github.com/wdebruij/packetdrill/commits/mtu_probe-1
Link: http://patchwork.ozlabs.org/patch/1143278/#2232897
Fixes: 4ed2d765df ("net-timestamp: TCP timestamping")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Rutsky reported stuck TCP sessions after memory pressure
events. Edge Trigger epoll() user would never receive an EPOLLOUT
notification allowing them to retry a sendmsg().
Jason tested the case of sk_stream_alloc_skb() returning NULL,
but there are other paths that could lead both sendmsg() and sendpage()
to return -1 (EAGAIN), with an empty skb queued on the write queue.
This patch makes sure we remove this empty skb so that
Jason code can detect that the queue is empty, and
call sk->sk_write_space(sk) accordingly.
Fixes: ce5ec44099 ("tcp: ensure epoll edge trigger wakeup when write queue is empty")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason Baron <jbaron@akamai.com>
Reported-by: Vladimir Rutsky <rutsky@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An excerpt from netlink(7) man page,
In multipart messages (multiple nlmsghdr headers with associated payload
in one byte stream) the first and all following headers have the
NLM_F_MULTI flag set, except for the last header which has the type
NLMSG_DONE.
but, after (ee28906) there is a missing NLM_F_MULTI flag in the middle of a
FIB dump. The result is user space applications following above man page
excerpt may get confused and may stop parsing msg believing something went
wrong.
In the golang netlink lib [0] the library logic stops parsing believing the
message is not a multipart message. Found this running Cilium[1] against
net-next while adding a feature to auto-detect routes. I noticed with
multiple route tables we no longer could detect the default routes on net
tree kernels because the library logic was not returning them.
Fix this by handling the fib_dump_info_fnhe() case the same way the
fib_dump_info() handles it by passing the flags argument through the
call chain and adding a flags argument to rt_fill_info().
Tested with Cilium stack and auto-detection of routes works again. Also
annotated libs to dump netlink msgs and inspected NLM_F_MULTI and
NLMSG_DONE flags look correct after this.
Note: In inet_rtm_getroute() pass rt_fill_info() '0' for flags the same
as is done for fib_dump_info() so this looks correct to me.
[0] https://github.com/vishvananda/netlink/
[1] https://github.com/cilium/
Fixes: ee28906fd7 ("ipv4: Dump route exceptions if requested")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __icmp_send() there is a possibility that the rt->dst.dev is NULL,
e,g, with tunnel collect_md mode, which will cause kernel crash.
Here is what the code path looks like, for GRE:
- ip6gre_tunnel_xmit
- ip6gre_xmit_ipv4
- __gre6_xmit
- ip6_tnl_xmit
- if skb->len - t->tun_hlen - eth_hlen > mtu; return -EMSGSIZE
- icmp_send
- net = dev_net(rt->dst.dev); <-- here
The reason is __metadata_dst_init() init dst->dev to NULL by default.
We could not fix it in __metadata_dst_init() as there is no dev supplied.
On the other hand, the reason we need rt->dst.dev is to get the net.
So we can just try get it from skb->dev when rt->dst.dev is NULL.
v4: Julian Anastasov remind skb->dev also could be NULL. We'd better
still use dst.dev and do a check to avoid crash.
v3: No changes.
v2: fix the issue in __icmp_send() instead of updating shared dst dev
in {ip_md, ip6}_tunnel_xmit.
Fixes: c8b34e680a ("ip_tunnel: Add tnl_update_pmtu in ip_md_tunnel_xmit")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable err is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused Value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull RCU and LKMM changes from Paul E. McKenney:
- A few more RCU flavor consolidation cleanups.
- Miscellaneous fixes.
- Updates to RCU's list-traversal macros improving lockdep usability.
- Torture-test updates.
- Forward-progress improvements for no-CBs CPUs: Avoid ignoring
incoming callbacks during grace-period waits.
- Forward-progress improvements for no-CBs CPUs: Use ->cblist
structure to take advantage of others' grace periods.
- Also added a small commit that avoids needlessly inflicting
scheduler-clock ticks on callback-offloaded CPUs.
- Forward-progress improvements for no-CBs CPUs: Reduce contention
on ->nocb_lock guarding ->cblist.
- Forward-progress improvements for no-CBs CPUs: Add ->nocb_bypass
list to further reduce contention on ->nocb_lock guarding ->cblist.
- LKMM updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
it expects a unsigned int, but got a __be32
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in ip_mc_inc_group, memory allocation flag, not mcast mode, is expected
by __ip_mc_inc_group
similar issue in __ip_mc_join_group, both mcase mode and gfp_t are needed
here, so use ____ip_mc_inc_group(...)
Fixes: 9fb20801da ("net: Fix ip_mc_{dec,inc}_group allocation context")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer members of an object with static storage duration, if not
explicitly initialized, will be initialized to a NULL pointer. The
net namespace API checks if this pointer is not NULL before using it,
it are safe to remove the function.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Rename mss field to mss_option field in synproxy, from Fernando Mancera.
2) Use SYSCTL_{ZERO,ONE} definitions in conntrack, from Matteo Croce.
3) More strict validation of IPVS sysctl values, from Junwei Hu.
4) Remove unnecessary spaces after on the right hand side of assignments,
from yangxingwu.
5) Add offload support for bitwise operation.
6) Extend the nft_offload_reg structure to store immediate date.
7) Collapse several ip_set header files into ip_set.h, from
Jeremy Sowden.
8) Make netfilter headers compile with CONFIG_KERNEL_HEADER_TEST=y,
from Jeremy Sowden.
9) Fix several sparse warnings due to missing prototypes, from
Valdis Kletnieks.
10) Use static lock initialiser to ensure connlabel spinlock is
initialized on boot time to fix sched/act_ct.c, patch
from Florian Westphal.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
There is a small merge conflict in libbpf (Cc Andrii so he's in the loop
as well):
for (i = 1; i <= btf__get_nr_types(btf); i++) {
t = (struct btf_type *)btf__type_by_id(btf, i);
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
<<<<<<< HEAD
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t+1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && kind == BTF_KIND_DATASEC) {
=======
t->size = sizeof(int);
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 32);
} else if (!has_datasec && btf_is_datasec(t)) {
>>>>>>> 72ef80b5ee
/* replace DATASEC with STRUCT */
Conflict is between the two commits 1d4126c4e1 ("libbpf: sanitize VAR to
conservative 1-byte INT") and b03bc6853c ("libbpf: convert libbpf code to
use new btf helpers"), so we need to pick the sanitation fixup as well as
use the new btf_is_datasec() helper and the whitespace cleanup. Looks like
the following:
[...]
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && btf_is_datasec(t)) {
/* replace DATASEC with STRUCT */
[...]
The main changes are:
1) Addition of core parts of compile once - run everywhere (co-re) effort,
that is, relocation of fields offsets in libbpf as well as exposure of
kernel's own BTF via sysfs and loading through libbpf, from Andrii.
More info on co-re: http://vger.kernel.org/bpfconf2019.html#session-2
and http://vger.kernel.org/lpc-bpf2018.html#session-2
2) Enable passing input flags to the BPF flow dissector to customize parsing
and allowing it to stop early similar to the C based one, from Stanislav.
3) Add a BPF helper function that allows generating SYN cookies from XDP and
tc BPF, from Petar.
4) Add devmap hash-based map type for more flexibility in device lookup for
redirects, from Toke.
5) Improvements to XDP forwarding sample code now utilizing recently enabled
devmap lookups, from Jesper.
6) Add support for reporting the effective cgroup progs in bpftool, from Jakub
and Takshak.
7) Fix reading kernel config from bpftool via /proc/config.gz, from Peter.
8) Fix AF_XDP umem pages mapping for 32 bit architectures, from Ivan.
9) Follow-up to add two more BPF loop tests for the selftest suite, from Alexei.
10) Add perf event output helper also for other skb-based program types, from Allan.
11) Fix a co-re related compilation error in selftests, from Yonghong.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The current implementation of TCP MTU probing can considerably
underestimate the MTU on lossy connections allowing the MSS to get down to
48. We have found that in almost all of these cases on our networks these
paths can handle much larger MTUs meaning the connections are being
artificially limited. Even though TCP MTU probing can raise the MSS back up
we have seen this not to be the case causing connections to be "stuck" with
an MSS of 48 when heavy loss is present.
Prior to pushing out this change we could not keep TCP MTU probing enabled
b/c of the above reasons. Now with a reasonble floor set we've had it
enabled for the past 6 months.
The new sysctl will still default to TCP_MIN_SND_MSS (48), but gives
administrators the ability to control the floor of MSS probing.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from commit d41a69f1d3 ("tcp: make tcp_sendmsg() aware of socket backlog")
loopback flows got hurt, because for each skb sent, the socket receives an
immediate ACK and sk_flush_backlog() causes extra work.
Intent was to not let the backlog grow too much, but we went a bit too far.
We can check the backlog every 16 skbs (about 1MB chunks)
to increase TCP over loopback performance by about 15 %
Note that the call to sk_flush_backlog() handles a single ACK,
thanks to coalescing done on backlog, but cleans the 16 skbs
found in rtx rb-tree.
Reported-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit applies the consolidated list_for_each_entry_rcu() support
for lockdep conditions.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
sk_validate_xmit_skb() and drivers depend on the sk member of
struct sk_buff to identify segments requiring encryption.
Any operation which removes or does not preserve the original TLS
socket such as skb_orphan() or skb_clone() will cause clear text
leaks.
Make the TCP socket underlying an offloaded TLS connection
mark all skbs as decrypted, if TLS TX is in offload mode.
Then in sk_validate_xmit_skb() catch skbs which have no socket
(or a socket with no validation) and decrypted flag set.
Note that CONFIG_SOCK_VALIDATE_XMIT, CONFIG_TLS_DEVICE and
sk->sk_validate_xmit_skb are slightly interchangeable right now,
they all imply TLS offload. The new checks are guarded by
CONFIG_TLS_DEVICE because that's the option guarding the
sk_buff->decrypted member.
Second, smaller issue with orphaning is that it breaks
the guarantee that packets will be delivered to device
queues in-order. All TLS offload drivers depend on that
scheduling property. This means skb_orphan_partial()'s
trick of preserving partial socket references will cause
issues in the drivers. We need a full orphan, and as a
result netem delay/throttling will cause all TLS offload
skbs to be dropped.
Reusing the sk_buff->decrypted flag also protects from
leaking clear text when incoming, decrypted skb is redirected
(e.g. by TC).
See commit 0608c69c9a ("bpf: sk_msg, sock{map|hash} redirect
through ULP") for justification why the internal flag is safe.
The only location which could leak the flag in is tcp_bpf_sendmsg(),
which is taken care of by clearing the previously unused bit.
v2:
- remove superfluous decrypted mark copy (Willem);
- remove the stale doc entry (Boris);
- rely entirely on EOR marking to prevent coalescing (Boris);
- use an internal sendpages flag instead of marking the socket
(Boris).
v3 (Willem):
- reorganize the can_skb_orphan_partial() condition;
- fix the flag leak-in through tcp_bpf_sendmsg.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit d4289fcc9b ("net: IP6 defrag: use rbtrees for IPv6
defrag"), a netperf UDP_STREAM test[0] using big IPv6 datagrams (thus
generating many fragments) and running over an IPsec tunnel, reported
more than 6Gbps throughput. After that patch, the same test gets only
9Mbps when receiving on a be2net nic (driver can make a big difference
here, for example, ixgbe doesn't seem to be affected).
By reusing the IPv4 defragmentation code, IPv6 lost fragment coalescing
(IPv4 fragment coalescing was dropped by commit 14fe22e334 ("Revert
"ipv4: use skb coalescing in defragmentation"")).
Without fragment coalescing, be2net runs out of Rx ring entries and
starts to drop frames (ethtool reports rx_drops_no_frags errors). Since
the netperf traffic is only composed of UDP fragments, any lost packet
prevents reassembly of the full datagram. Therefore, fragments which
have no possibility to ever get reassembled pile up in the reassembly
queue, until the memory accounting exeeds the threshold. At that point
no fragment is accepted anymore, which effectively discards all
netperf traffic.
When reassembly timeout expires, some stale fragments are removed from
the reassembly queue, so a few packets can be received, reassembled
and delivered to the netperf receiver. But the nic still drops frames
and soon the reassembly queue gets filled again with stale fragments.
These long time frames where no datagram can be received explain why
the performance drop is so significant.
Re-introducing fragment coalescing is enough to get the initial
performances again (6.6Gbps with be2net): driver doesn't drop frames
anymore (no more rx_drops_no_frags errors) and the reassembly engine
works at full speed.
This patch is quite conservative and only coalesces skbs for local
IPv4 and IPv6 delivery (in order to avoid changing skb geometry when
forwarding). Coalescing could be extended in the future if need be, as
more scenarios would probably benefit from it.
[0]: Test configuration
Sender:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir in tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir out tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
netserver -D -L fc00:2::1
Receiver:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir in tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir out tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
netperf -H fc00:2::1 -f k -P 0 -L fc00:1::1 -l 60 -t UDP_STREAM -I 99,5 -i 5,5 -T5,5 -6
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introduce "mss_encode" field in the synproxy_options struct the field
"mss" is a little confusing. It has been renamed to "mss_option".
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows generation of a SYN cookie before an SKB has been
allocated, as is the case at XDP.
Signed-off-by: Petar Penkov <ppenkov@google.com>
Reviewed-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This allows us to call this function before an SKB has been
allocated.
Signed-off-by: Petar Penkov <ppenkov@google.com>
Reviewed-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-07-25
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix segfault in libbpf, from Andrii.
2) fix gso_segs access, from Eric.
3) tls/sockmap fixes, from Jakub and John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need the same checks introduced by commit cb9f1b7838
("ip: validate header length on virtual device xmit") for
ipip tunnel.
Fixes: cb9f1b7838 ("ip: validate header length on virtual device xmit")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a map free is called and in parallel a socket is closed we
have two paths that can potentially reset the socket prot ops, the
bpf close() path and the map free path. This creates a problem
with which prot ops should be used from the socket closed side.
If the map_free side completes first then we want to call the
original lowest level ops. However, if the tls path runs first
we want to call the sockmap ops. Additionally there was no locking
around prot updates in TLS code paths so the prot ops could
be changed multiple times once from TLS path and again from sockmap
side potentially leaving ops pointed at either TLS or sockmap
when psock and/or tls context have already been destroyed.
To fix this race first only update ops inside callback lock
so that TLS, sockmap and lowest level all agree on prot state.
Second and a ULP callback update() so that lower layers can
inform the upper layer when they are being removed allowing the
upper layer to reset prot ops.
This gets us close to allowing sockmap and tls to be stacked
in arbitrary order but will save that patch for *next trees.
v4:
- make sure we don't free things for device;
- remove the checks which swap the callbacks back
only if TLS is at the top.
Reported-by: syzbot+06537213db7ba2745c4a@syzkaller.appspotmail.com
Fixes: 02c558b2d5 ("bpf: sockmap, support for msg_peek in sk_msg with redirect ingress")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some applications set tiny SO_SNDBUF values and expect
TCP to just work. Recent patches to address CVE-2019-11478
broke them in case of losses, since retransmits might
be prevented.
We should allow these flows to make progress.
This patch allows the first and last skb in retransmit queue
to be split even if memory limits are hit.
It also adds the some room due to the fact that tcp_sendmsg()
and tcp_sendpage() might overshoot sk_wmem_queued by about one full
TSO skb (64KB size). Note this allowance was already present
in stable backports for kernels < 4.15
Note for < 4.15 backports :
tcp_rtx_queue_tail() will probably look like :
static inline struct sk_buff *tcp_rtx_queue_tail(const struct sock *sk)
{
struct sk_buff *skb = tcp_send_head(sk);
return skb ? tcp_write_queue_prev(sk, skb) : tcp_write_queue_tail(sk);
}
Fixes: f070ef2ac6 ("tcp: tcp_fragment() should apply sane memory limits")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrew Prout <aprout@ll.mit.edu>
Tested-by: Andrew Prout <aprout@ll.mit.edu>
Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Tested-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Christoph Paasch <cpaasch@apple.com>
Cc: Jonathan Looney <jtl@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix a deadlock when module is requested via netlink_bind()
in nfnetlink, from Florian Westphal.
2) Fix ipt_rpfilter and ip6t_rpfilter with VRF, from Miaohe Lin.
3) Skip master comparison in SIP helper to fix expectation clash
under two valid scenarios, from xiao ruizhu.
4) Remove obsolete comments in nf_conntrack codebase, from
Yonatan Goldschmidt.
5) Fix redirect extension module autoload, from Christian Hesse.
6) Fix incorrect mssg option sent to client in synproxy,
from Fernando Fernandez.
7) Fix incorrect window calculations in TCP conntrack, from
Florian Westphal.
8) Don't bail out when updating basechain policy due to recent
offload works, also from Florian.
9) Allow symhash to use modulus 1 as other hash extensions do,
from Laura.Garcia.
10) Missing NAT chain module autoload for the inet family,
from Phil Sutter.
11) Fix missing adjustment of TCP RST packet in synproxy,
from Fernando Fernandez.
12) Skip EAGAIN path when nft_meta_bridge is built-in or
not selected.
13) Conntrack bridge does not depend on nf_tables_bridge.
14) Turn NF_TABLES_BRIDGE into tristate to fix possible
link break of nft_meta_bridge, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix AF_XDP cq entry leak, from Ilya Maximets.
2) Fix handling of PHY power-down on RTL8411B, from Heiner Kallweit.
3) Add some new PCI IDs to iwlwifi, from Ihab Zhaika.
4) Fix handling of neigh timers wrt. entries added by userspace, from
Lorenzo Bianconi.
5) Various cases of missing of_node_put(), from Nishka Dasgupta.
6) The new NET_ACT_CT needs to depend upon NF_NAT, from Yue Haibing.
7) Various RDS layer fixes, from Gerd Rausch.
8) Fix some more fallout from TCQ_F_CAN_BYPASS generalization, from
Cong Wang.
9) Fix FIB source validation checks over loopback, also from Cong Wang.
10) Use promisc for unsupported number of filters, from Justin Chen.
11) Missing sibling route unlink on failure in ipv6, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
tcp: fix tcp_set_congestion_control() use from bpf hook
ag71xx: fix return value check in ag71xx_probe()
ag71xx: fix error return code in ag71xx_probe()
usb: qmi_wwan: add D-Link DWM-222 A2 device ID
bnxt_en: Fix VNIC accounting when enabling aRFS on 57500 chips.
net: dsa: sja1105: Fix missing unlock on error in sk_buff()
gve: replace kfree with kvfree
selftests/bpf: fix test_xdp_noinline on s390
selftests/bpf: fix "valid read map access into a read-only array 1" on s390
net/mlx5: Replace kfree with kvfree
MAINTAINERS: update netsec driver
ipv6: Unlink sibling route in case of failure
liquidio: Replace vmalloc + memset with vzalloc
udp: Fix typo in net/ipv4/udp.c
net: bcmgenet: use promisc for unsupported filters
ipv6: rt6_check should return NULL if 'from' is NULL
tipc: initialize 'validated' field of received packets
selftests: add a test case for rp_filter
fib: relax source validation check for loopback packets
mlxsw: spectrum: Do not process learned records with a dummy FID
...
Neal reported incorrect use of ns_capable() from bpf hook.
bpf_setsockopt(...TCP_CONGESTION...)
-> tcp_set_congestion_control()
-> ns_capable(sock_net(sk)->user_ns, CAP_NET_ADMIN)
-> ns_capable_common()
-> current_cred()
-> rcu_dereference_protected(current->cred, 1)
Accessing 'current' in bpf context makes no sense, since packets
are processed from softirq context.
As Neal stated : The capability check in tcp_set_congestion_control()
was written assuming a system call context, and then was reused from
a BPF call site.
The fix is to add a new parameter to tcp_set_congestion_control(),
so that the ns_capable() call is only performed under the right
context.
Fixes: 91b5b21c7c ("bpf: Add support for changing congestion control")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In a rare case where we redirect local packets from veth to lo,
these packets fail to pass the source validation when rp_filter
is turned on, as the tracing shows:
<...>-311708 [040] ..s1 7951180.957825: fib_table_lookup: table 254 oif 0 iif 1 src 10.53.180.130 dst 10.53.180.130 tos 0 scope 0 flags 0
<...>-311708 [040] ..s1 7951180.957826: fib_table_lookup_nh: nexthop dev eth0 oif 4 src 10.53.180.130
So, the fib table lookup returns eth0 as the nexthop even though
the packets are local and should be routed to loopback nonetheless,
but they can't pass the dev match check in fib_info_nh_uses_dev()
without this patch.
It should be safe to relax this check for this special case, as
normally packets coming out of loopback device still have skb_dst
so they won't even hit this slow path.
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now synproxy sends the mss value set by the user on client syn-ack packet
instead of the mss value that client announced.
Fixes: 48b1de4c11 ("netfilter: add SYNPROXY core/target")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In 9fb9cbb108 ("[NETFILTER]: Add nf_conntrack subsystem.") the new
generic nf_conntrack was introduced, and it came to supersede the old
ip_conntrack.
This change updates (some) of the obsolete comments referring to old
file/function names of the ip_conntrack mechanism, as well as removes a
few self-referencing comments that we shouldn't maintain anymore.
I did not update any comments referring to historical actions (e.g,
comments like "this file was derived from ..." were left untouched, even
if the referenced file is no longer here).
Signed-off-by: Yonatan Goldschmidt <yon.goldschmidt@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When conntracks change during a dialog, SDP messages may be sent from
different conntracks to establish expects with identical tuples. In this
case expects conflict may be detected for the 2nd SDP message and end up
with a process failure.
The fixing here is to reuse an existing expect who has the same tuple for a
different conntrack if any.
Here are two scenarios for the case.
1)
SERVER CPE
| INVITE SDP |
5060 |<----------------------|5060
| 100 Trying |
5060 |---------------------->|5060
| 183 SDP |
5060 |---------------------->|5060 ===> Conntrack 1
| PRACK |
50601 |<----------------------|5060
| 200 OK (PRACK) |
50601 |---------------------->|5060
| 200 OK (INVITE) |
5060 |---------------------->|5060
| ACK |
50601 |<----------------------|5060
| |
|<--- RTP stream ------>|
| |
| INVITE SDP (t38) |
50601 |---------------------->|5060 ===> Conntrack 2
With a certain configuration in the CPE, SIP messages "183 with SDP" and
"re-INVITE with SDP t38" will go through the sip helper to create
expects for RTP and RTCP.
It is okay to create RTP and RTCP expects for "183", whose master
connection source port is 5060, and destination port is 5060.
In the "183" message, port in Contact header changes to 50601 (from the
original 5060). So the following requests e.g. PRACK and ACK are sent to
port 50601. It is a different conntrack (let call Conntrack 2) from the
original INVITE (let call Conntrack 1) due to the port difference.
In this example, after the call is established, there is RTP stream but no
RTCP stream for Conntrack 1, so the RTP expect created upon "183" is
cleared, and RTCP expect created for Conntrack 1 retains.
When "re-INVITE with SDP t38" arrives to create RTP&RTCP expects, current
ALG implementation will call nf_ct_expect_related() for RTP and RTCP. The
expects tuples are identical to those for Conntrack 1. RTP expect for
Conntrack 2 succeeds in creation as the one for Conntrack 1 has been
removed. RTCP expect for Conntrack 2 fails in creation because it has
idential tuples and 'conflict' with the one retained for Conntrack 1. And
then result in a failure in processing of the re-INVITE.
2)
SERVER A CPE
| REGISTER |
5060 |<------------------| 5060 ==> CT1
| 200 |
5060 |------------------>| 5060
| |
| INVITE SDP(1) |
5060 |<------------------| 5060
| 300(multi choice) |
5060 |------------------>| 5060 SERVER B
| ACK |
5060 |<------------------| 5060
| INVITE SDP(2) |
5060 |-------------------->| 5060 ==> CT2
| 100 |
5060 |<--------------------| 5060
| 200(contact changes)|
5060 |<--------------------| 5060
| ACK |
5060 |-------------------->| 50601 ==> CT3
| |
|<--- RTP stream ---->|
| |
| BYE |
5060 |<--------------------| 50601
| 200 |
5060 |-------------------->| 50601
| INVITE SDP(3) |
5060 |<------------------| 5060 ==> CT1
CPE sends an INVITE request(1) to Server A, and creates a RTP&RTCP expect
pair for this Conntrack 1 (CT1). Server A responds 300 to redirect to
Server B. The RTP&RTCP expect pairs created on CT1 are removed upon 300
response.
CPE sends the INVITE request(2) to Server B, and creates an expect pair
for the new conntrack (due to destination address difference), let call
CT2. Server B changes the port to 50601 in 200 OK response, and the
following requests ACK and BYE from CPE are sent to 50601. The call is
established. There is RTP stream and no RTCP stream. So RTP expect is
removed and RTCP expect for CT2 retains.
As BYE request is sent from port 50601, it is another conntrack, let call
CT3, different from CT2 due to the port difference. So the BYE request will
not remove the RTCP expect for CT2.
Then another outgoing call is made, with the same RTP port being used (not
definitely but possibly). CPE firstly sends the INVITE request(3) to Server
A, and tries to create a RTP&RTCP expect pairs for this CT1. In current ALG
implementation, the RTCP expect for CT1 fails in creation because it
'conflicts' with the residual one for CT2. As a result the INVITE request
fails to send.
Signed-off-by: xiao ruizhu <katrina.xiaorz@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When firewalld is enabled with ipv4/ipv6 rpfilter, vrf
ipv4/ipv6 packets will be dropped. Vrf device will pass
through netfilter hook twice. One with enslaved device
and another one with l3 master device. So in device may
dismatch witch out device because out device is always
enslaved device.So failed with the check of the rpfilter
and drop the packets by mistake.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
If an app is playing tricks to reuse a socket via tcp_disconnect(),
bytes_acked/received needs to be reset to 0. Otherwise tcp_info will
report the sum of the current and the old connection..
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 0df48c26d8 ("tcp: add tcpi_bytes_acked to tcp_info")
Fixes: bdd1f9edac ("tcp: add tcpi_bytes_received to tcp_info")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 363887a2cd ("ipv4: Support multipath hashing on inner IP pkts
for GRE tunnel") supports multipath policy value of 2, Layer 3 or inner
Layer 3 if present, but it only considers inner IPv4. There is a use
case of IPv6 is tunneled by IPv4 GRE, thus add the ability to hash on
inner IPv6 addresses.
Fixes: 363887a2cd ("ipv4: Support multipath hashing on inner IP pkts for GRE tunnel")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ip_neigh_gw4() and ip_neigh_gw6() can return either a valid pointer
or an error pointer, but the code currently checks that the pointer is
not NULL.
Fix this by checking that the pointer is not an error pointer, as this
can result in a NULL pointer dereference [1]. Specifically, I believe
that what happened is that ip_neigh_gw4() returned '-EINVAL'
(0xffffffffffffffea) to which the offset of 'refcnt' (0x70) was added,
which resulted in the address 0x000000000000005a.
[1]
BUG: KASAN: null-ptr-deref in refcount_inc_not_zero_checked+0x6e/0x180
Read of size 4 at addr 000000000000005a by task swapper/2/0
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.2.0-rc6-custom-reg-179657-gaa32d89 #396
Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017
Call Trace:
<IRQ>
dump_stack+0x73/0xbb
__kasan_report+0x188/0x1ea
kasan_report+0xe/0x20
refcount_inc_not_zero_checked+0x6e/0x180
ipv4_neigh_lookup+0x365/0x12c0
__neigh_update+0x1467/0x22f0
arp_process.constprop.6+0x82e/0x1f00
__netif_receive_skb_one_core+0xee/0x170
process_backlog+0xe3/0x640
net_rx_action+0x755/0xd90
__do_softirq+0x29b/0xae7
irq_exit+0x177/0x1c0
smp_apic_timer_interrupt+0x164/0x5e0
apic_timer_interrupt+0xf/0x20
</IRQ>
Fixes: 5c9f7c1dfc ("ipv4: Add helpers for neigh lookup for nexthop")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2019-07-05
1) A lot of work to remove indirections from the xfrm code.
From Florian Westphal.
2) Fix a WARN_ON with ipv6 that triggered because of a
forgotten break statement. From Florian Westphal.
3) Remove xfrmi_init_net, it is not needed.
From Li RongQing.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-07-03
The following pull-request contains BPF updates for your *net-next* tree.
There is a minor merge conflict in mlx5 due to 8960b38932 ("linux/dim:
Rename externally used net_dim members") which has been pulled into your
tree in the meantime, but resolution seems not that bad ... getting current
bpf-next out now before there's coming more on mlx5. ;) I'm Cc'ing Saeed
just so he's aware of the resolution below:
** First conflict in drivers/net/ethernet/mellanox/mlx5/core/en_main.c:
<<<<<<< HEAD
static int mlx5e_open_cq(struct mlx5e_channel *c,
struct dim_cq_moder moder,
struct mlx5e_cq_param *param,
struct mlx5e_cq *cq)
=======
int mlx5e_open_cq(struct mlx5e_channel *c, struct net_dim_cq_moder moder,
struct mlx5e_cq_param *param, struct mlx5e_cq *cq)
>>>>>>> e5a3e259ef
Resolution is to take the second chunk and rename net_dim_cq_moder into
dim_cq_moder. Also the signature for mlx5e_open_cq() in ...
drivers/net/ethernet/mellanox/mlx5/core/en.h +977
... and in mlx5e_open_xsk() ...
drivers/net/ethernet/mellanox/mlx5/core/en/xsk/setup.c +64
... needs the same rename from net_dim_cq_moder into dim_cq_moder.
** Second conflict in drivers/net/ethernet/mellanox/mlx5/core/en_main.c:
<<<<<<< HEAD
int cpu = cpumask_first(mlx5_comp_irq_get_affinity_mask(priv->mdev, ix));
struct dim_cq_moder icocq_moder = {0, 0};
struct net_device *netdev = priv->netdev;
struct mlx5e_channel *c;
unsigned int irq;
=======
struct net_dim_cq_moder icocq_moder = {0, 0};
>>>>>>> e5a3e259ef
Take the second chunk and rename net_dim_cq_moder into dim_cq_moder
as well.
Let me know if you run into any issues. Anyway, the main changes are:
1) Long-awaited AF_XDP support for mlx5e driver, from Maxim.
2) Addition of two new per-cgroup BPF hooks for getsockopt and
setsockopt along with a new sockopt program type which allows more
fine-grained pass/reject settings for containers. Also add a sock_ops
callback that can be selectively enabled on a per-socket basis and is
executed for every RTT to help tracking TCP statistics, both features
from Stanislav.
3) Follow-up fix from loops in precision tracking which was not propagating
precision marks and as a result verifier assumed that some branches were
not taken and therefore wrongly removed as dead code, from Alexei.
4) Fix BPF cgroup release synchronization race which could lead to a
double-free if a leaf's cgroup_bpf object is released and a new BPF
program is attached to the one of ancestor cgroups in parallel, from Roman.
5) Support for bulking XDP_TX on veth devices which improves performance
in some cases by around 9%, from Toshiaki.
6) Allow for lookups into BPF devmap and improve feedback when calling into
bpf_redirect_map() as lookup is now performed right away in the helper
itself, from Toke.
7) Add support for fq's Earliest Departure Time to the Host Bandwidth
Manager (HBM) sample BPF program, from Lawrence.
8) Various cleanups and minor fixes all over the place from many others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids an indirect call per syscall for common ipv4 transports
v1 -> v2:
- avoid unneeded reclaration for udp_sendmsg, as suggested by Willem
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is replicated verbatim in multiple places, and the next
patches will introduce an additional user for it. Factor out a
helper and use it where appropriate. No functional change intended.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If IPV6 was disabled, then ss command would cause a kernel warning
because the command was attempting to dump IPV6 socket information.
The fix is to just remove the warning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202249
Fixes: 432490f9d4 ("net: ip, diag -- Add diag interface for raw sockets")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performance impact should be minimal because it's under a new
BPF_SOCK_OPS_RTT_CB_FLAG flag that has to be explicitly enabled.
Suggested-by: Eric Dumazet <edumazet@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Priyaranjan Jha <priyarjha@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In commit ee28906fd7 ("ipv4: Dump route exceptions if requested") I
added a counter of per-node dumped routes (including actual routes and
exceptions), analogous to the existing counter for dumped nodes. Dumping
exceptions means we need to also keep track of how many routes are dumped
for each node: this would be just one route per node, without exceptions.
When netlink strict checking is not enabled, we dump both routes and
exceptions at the same time: the RTM_F_CLONED flag is not used as a
filter. In this case, the per-node counter 'i_fa' is incremented by one
to track the single dumped route, then also incremented by one for each
exception dumped, and then stored as netlink callback argument as skip
counter, 's_fa', to be used when a partial dump operation restarts.
The per-node counter needs to be increased by one also when we skip a
route (exception) due to a previous non-zero skip counter, because it
needs to match the existing skip counter, if we are dumping both routes
and exceptions. I missed this, and only incremented the counter, for
regular routes, if the previous skip counter was zero. This means that,
in case of a mixed dump, partial dump operations after the first one
will start with a mismatching skip counter value, one less than expected.
This means in turn that the first exception for a given node is skipped
every time a partial dump operation restarts, if netlink strict checking
is not enabled (iproute < 5.0).
It turns out I didn't repeat the test in its final version, commit
de755a8513 ("selftests: pmtu: Introduce list_flush_ipv4_exception test
case"), which also counts the number of route exceptions returned, with
iproute2 versions < 5.0 -- I was instead using the equivalent of the IPv6
test as it was before commit b964641e99 ("selftests: pmtu: Make
list_flush_ipv6_exception test more demanding").
Always increment the per-node counter by one if we previously dumped
a regular route, so that it matches the current skip counter.
Fixes: ee28906fd7 ("ipv4: Dump route exceptions if requested")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use blackhole_netdev instead of 'lo' device with lower MTU when marking
dst "dead".
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Tested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the situation where an IPV6 only flag is applied to an IPv4 address:
# ip addr add 192.0.2.1/24 dev dummy0 nodad home mngtmpaddr noprefixroute
# ip -4 addr show dev dummy0
2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
inet 192.0.2.1/24 scope global noprefixroute dummy0
valid_lft forever preferred_lft forever
Or worse, by sending a malicious netlink command:
# ip -4 addr show dev dummy0
2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
inet 192.0.2.1/24 scope global nodad optimistic dadfailed home tentative mngtmpaddr noprefixroute stable-privacy dummy0
valid_lft forever preferred_lft forever
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
esp4_get_mtu and esp6_get_mtu are exactly the same, the only difference
is a single sizeof() (ipv4 vs. ipv6 header).
Merge both into xfrm_state_mtu() and remove the indirection.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Tools such as vpnc try to flush routes when run inside network
namespaces by writing 1 into /proc/sys/net/ipv4/route/flush. This
currently does not work because flush is not enabled in non-initial
network namespaces.
Since routes are per network namespace it is safe to enable
/proc/sys/net/ipv4/route/flush in there.
Link: https://github.com/lxc/lxd/issues/4257
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
secondary address promotion causes infinite loop -- it arranges
for ifa->ifa_next to point back to itself.
Problem is that 'prev_prom' and 'last_prim' might point at the same entry,
so 'last_sec' pointer must be obtained after prev_prom->next update.
Fixes: 2638eb8b50 ("net: ipv4: provide __rcu annotation for ifa_list")
Reported-by: Ran Rozenstein <ranro@mellanox.com>
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast or broadcast egress packets have rt_iif set to the oif. These
packets might be recirculated back as input and lookup to the raw
sockets may fail because they are bound to the incoming interface
(skb_iif). If rt_iif is not zero, during the lookup, inet_iif() function
returns rt_iif instead of skb_iif. Hence, the lookup fails.
v2: Make it non vrf specific (David Ahern). Reword the changelog to
reflect it.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 19e4e76806 ("ipv4: Fix raw socket lookup for local
traffic"), the dif argument to __raw_v4_lookup() is coming from the
returned value of inet_iif() but the change was done only for the first
lookup. Subsequent lookups in the while loop still use skb->dev->ifIndex.
Fixes: 19e4e76806 ("ipv4: Fix raw socket lookup for local traffic")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve conflict between d2912cb15b ("treewide: Replace GPLv2
boilerplate/reference with SPDX - rule 500") removing the GPL disclaimer
and fe03d47456 ("Update my email address") which updates Jozsef
Kadlecsik's email.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since commit 4895c771c7 ("ipv4: Add FIB nexthop exceptions."), cached
exception routes are stored as a separate entity, so they are not dumped
on a FIB dump, even if the RTM_F_CLONED flag is passed.
This implies that the command 'ip route list cache' doesn't return any
result anymore.
If the RTM_F_CLONED is passed, and strict checking requested, retrieve
nexthop exception routes and dump them. If no strict checking is
requested, filtering can't be performed consistently: dump everything in
that case.
With this, we need to add an argument to the netlink callback in order to
track how many entries were already dumped for the last leaf included in
a partial netlink dump.
A single additional argument is sufficient, even if we traverse logically
nested structures (nexthop objects, hash table buckets, bucket chains): it
doesn't matter if we stop in the middle of any of those, because they are
always traversed the same way. As an example, s_i values in [], s_fa
values in ():
node (fa) #1 [1]
nexthop #1
bucket #1 -> #0 in chain (1)
bucket #2 -> #0 in chain (2) -> #1 in chain (3) -> #2 in chain (4)
bucket #3 -> #0 in chain (5) -> #1 in chain (6)
nexthop #2
bucket #1 -> #0 in chain (7) -> #1 in chain (8)
bucket #2 -> #0 in chain (9)
--
node (fa) #2 [2]
nexthop #1
bucket #1 -> #0 in chain (1) -> #1 in chain (2)
bucket #2 -> #0 in chain (3)
it doesn't matter if we stop at (3), (4), (7) for "node #1", or at (2)
for "node #2": walking flattens all that.
It would even be possible to drop the distinction between the in-tree
(s_i) and in-node (s_fa) counter, but a further improvement might
advise against this. This is only as accurate as the existing tracking
mechanism for leaves: if a partial dump is restarted after exceptions
are removed or expired, we might skip some non-dumped entries.
To improve this, we could attach a 'sernum' attribute (similar to the
one used for IPv6) to nexthop entities, and bump this counter whenever
exceptions change: having a distinction between the two counters would
make this more convenient.
Listing of exception routes (modified routes pre-3.5) was tested against
these versions of kernel and iproute2:
iproute2
kernel 4.14.0 4.15.0 4.19.0 5.0.0 5.1.0
3.5-rc4 + + + + +
4.4
4.9
4.14
4.15
4.19
5.0
5.1
fixed + + + + +
v7:
- Move loop over nexthop objects to route.c, and pass struct fib_info
and table ID to it, not a struct fib_alias (suggested by David Ahern)
- While at it, note that the NULL check on fa->fa_info is redundant,
and the check on RTNH_F_DEAD is also not consistent with what's done
with regular route listing: just keep it for nhc_flags
- Rename entry point function for dumping exceptions to
fib_dump_info_fnhe(), and rearrange arguments for consistency with
fib_dump_info()
- Rename fnhe_dump_buckets() to fnhe_dump_bucket() and make it handle
one bucket at a time
- Expand commit message to describe why we can have a single "skip"
counter for all exceptions stored in bucket chains in nexthop objects
(suggested by David Ahern)
v6:
- Rebased onto net-next
- Loop over nexthop paths too. Move loop over fnhe buckets to route.c,
avoids need to export rt_fill_info() and to touch exceptions from
fib_trie.c. Pass NULL as flow to rt_fill_info(), it now allows that
(suggested by David Ahern)
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patch, we're going to use rt_fill_info() to dump exception
routes upon RTM_GETROUTE with NLM_F_ROOT, meaning userspace is requesting
a dump and not a specific route selection, which in turn implies the input
interface is not relevant. Update rt_fill_info() to handle a NULL
flowinfo.
v7: If fl4 is NULL, explicitly set r->rtm_tos to 0: it's not initialised
otherwise (spotted by David Ahern)
v6: New patch
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This functionally reverts the check introduced by commit
e8ba330ac0 ("rtnetlink: Update fib dumps for strict data checking")
as modified by commit e4e92fb160 ("net/ipv4: Bail early if user only
wants prefix entries").
As we are preparing to fix listing of IPv4 cached routes, we need to
give userspace a way to request them.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patches add back the ability to dump IPv4 and IPv6 exception
routes, and we need to allow selection of regular routes or exceptions.
Use RTM_F_CLONED as filter to decide whether to dump routes or exceptions:
iproute2 passes it in dump requests (except for IPv6 cache flush requests,
this will be fixed in iproute2) and this used to work as long as
exceptions were stored directly in the FIB, for both IPv4 and IPv6.
Caveat: if strict checking is not requested (that is, if the dump request
doesn't go through ip_valid_fib_dump_req()), we can't filter on protocol,
tables or route types.
In this case, filtering on RTM_F_CLONED would be inconsistent: we would
fix 'ip route list cache' by returning exception routes and at the same
time introduce another bug in case another selector is present, e.g. on
'ip route list cache table main' we would return all exception routes,
without filtering on tables.
Keep this consistent by applying no filters at all, and dumping both
routes and exceptions, if strict checking is not requested. iproute2
currently filters results anyway, and no unwanted results will be
presented to the user. The kernel will just dump more data than needed.
v7: No changes
v6: Rebase onto net-next, no changes
v5: New patch: add dump_routes and dump_exceptions flags in filter and
simply clear the unwanted one if strict checking is enabled, don't
ignore NLM_F_MATCH and don't set filter_set if NLM_F_MATCH is set.
Skip filtering altogether if no strict checking is requested:
selecting routes or exceptions only would be inconsistent with the
fact we can't filter on tables.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When arp_ignore=3, the NIC won't reply for scope host addresses, but
if enable route_locanet, we need to reply ip address with head 127 and
scope RT_SCOPE_HOST.
Fixes: d0daebc3d6 ("ipv4: Add interface option to enable routing of 127.0.0.0/8")
Signed-off-by: Shijie Luo <luoshijie1@huawei.com>
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppose we have two interfaces eth0 and eth1 in two hosts, follow
the same steps in the two hosts:
# sysctl -w net.ipv4.conf.eth1.route_localnet=1
# sysctl -w net.ipv4.conf.eth1.arp_announce=2
# ip route del 127.0.0.0/8 dev lo table local
and then set ip to eth1 in host1 like:
# ifconfig eth1 127.25.3.4/24
set ip to eth2 in host2 and ping host1:
# ifconfig eth1 127.25.3.14/24
# ping -I eth1 127.25.3.4
Well, host2 cannot connect to host1.
When set a ip address with head 127, the scope of the address defaults
to RT_SCOPE_HOST. In this situation, host2 will use arp_solicit() to
send a arp request for the mac address of host1 with ip
address 127.25.3.14. When arp_announce=2, inet_select_addr() cannot
select a correct saddr with condition ifa->ifa_scope > scope, because
ifa_scope is RT_SCOPE_HOST and scope is RT_SCOPE_LINK. Then,
inet_select_addr() will go to no_in_dev to lookup all interfaces to find
a primary ip and finally get the primary ip of eth0.
Here I add a localnet_scope defaults to RT_SCOPE_HOST, and when
route_localnet is enabled, this value changes to RT_SCOPE_LINK to make
inet_select_addr() find a correct primary ip as saddr of arp request.
Fixes: d0daebc3d6 ("ipv4: Add interface option to enable routing of 127.0.0.0/8")
Signed-off-by: Shijie Luo <luoshijie1@huawei.com>
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some changes to the TCP fastopen code to make it more robust
against future changes in the choice of key/cookie size, etc.
- Instead of keeping the SipHash key in an untyped u8[] buffer
and casting it to the right type upon use, use the correct
type directly. This ensures that the key will appear at the
correct alignment if we ever change the way these data
structures are allocated. (Currently, they are only allocated
via kmalloc so they always appear at the correct alignment)
- Use DIV_ROUND_UP when sizing the u64[] array to hold the
cookie, so it is always of sufficient size, even if
TCP_FASTOPEN_COOKIE_MAX is no longer a multiple of 8.
- Drop the 'len' parameter from the tcp_fastopen_reset_cipher()
function, which is no longer used.
- Add endian swabbing when setting the keys and calculating the hash,
to ensure that cookie values are the same for a given key and
source/destination address pair regardless of the endianness of
the server.
Note that none of these are functional changes wrt the current
state of the code, with the exception of the swabbing, which only
affects big endian systems.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix leak of unqueued fragments in ipv6 nf_defrag, from Guillaume
Nault.
2) Don't access the DDM interface unless the transceiver implements it
in bnx2x, from Mauro S. M. Rodrigues.
3) Don't double fetch 'len' from userspace in sock_getsockopt(), from
JingYi Hou.
4) Sign extension overflow in lio_core, from Colin Ian King.
5) Various netem bug fixes wrt. corrupted packets from Jakub Kicinski.
6) Fix epollout hang in hvsock, from Sunil Muthuswamy.
7) Fix regression in default fib6_type, from David Ahern.
8) Handle memory limits in tcp_fragment more appropriately, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
tcp: refine memory limit test in tcp_fragment()
inet: clear num_timeout reqsk_alloc()
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
net/af_iucv: build proper skbs for HiperTransport
net/af_iucv: remove GFP_DMA restriction for HiperTransport
net: dsa: mv88e6xxx: fix shift of FID bits in mv88e6185_g1_vtu_loadpurge()
hvsock: fix epollout hang from race condition
net/udp_gso: Allow TX timestamp with UDP GSO
net: netem: fix use after free and double free with packet corruption
net: netem: fix backlog accounting for corrupted GSO frames
net: lio_core: fix potential sign-extension overflow on large shift
tipc: pass tunnel dev as NULL to udp_tunnel(6)_xmit_skb
ip6_tunnel: allow not to count pkts on tstats by passing dev as NULL
ip_tunnel: allow not to count pkts on tstats by setting skb's dev to NULL
tun: wake up waitqueues after IFF_UP is set
net: remove duplicate fetch in sock_getsockopt
tipc: fix issues with early FAILOVER_MSG from peer
...
tcp_fragment() might be called for skbs in the write queue.
Memory limits might have been exceeded because tcp_sendmsg() only
checks limits at full skb (64KB) boundaries.
Therefore, we need to make sure tcp_fragment() wont punish applications
that might have setup very low SO_SNDBUF values.
Fixes: f070ef2ac6 ("tcp: tcp_fragment() should apply sane memory limits")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
This is the kernel change for the overall changes with this description:
Add capability to have rules matching IPv4 options. This is developed
mainly to support dropping of IP packets with loose and/or strict source
route route options.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This operation is handled by nf_synproxy_ipv4_init() now.
Fixes: d7f9b2f18e ("netfilter: synproxy: extract SYNPROXY infrastructure from {ipt, ip6t}_SYNPROXY")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
empty_child_inc/dec() use the ternary operator for conditional
operations. The conditions involve the post/pre in/decrement
operator and the operation is only performed when the condition
is *not* true. This is hard to parse for humans, use a regular
'if' construct instead and perform the in/decrement separately.
This also fixes two warnings that are emitted about the value
of the ternary expression being unused, when building the kernel
with clang + "kbuild: Remove unnecessary -Wno-unused-value"
(https://lore.kernel.org/patchwork/patch/1089869/):
CC net/ipv4/fib_trie.o
net/ipv4/fib_trie.c:351:2: error: expression result unused [-Werror,-Wunused-value]
++tn_info(n)->empty_children ? : ++tn_info(n)->full_children;
Fixes: 95f60ea3e9 ("fib_trie: Add collapse() and should_collapse() to resize")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this source code is licensed under general public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081204.871734026@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes an issue where TX Timestamps are not arriving on the error queue
when UDP_SEGMENT CMSG type is combined with CMSG type SO_TIMESTAMPING.
This can be illustrated with an updated updgso_bench_tx program which
includes the '-T' option to test for this condition. It also introduces
the '-P' option which will call poll() before reading the error queue.
./udpgso_bench_tx -4ucTPv -S 1472 -l2 -D 172.16.120.18
poll timeout
udp tx: 0 MB/s 1 calls/s 1 msg/s
The "poll timeout" message above indicates that TX timestamp never
arrived.
This patch preserves tx_flags for the first UDP GSO segment. Only the
first segment is timestamped, even though in some cases there may be
benefital in timestamping both the first and last segment.
Factors in deciding on first segment timestamp only:
- Timestamping both first and last segmented is not feasible. Hardware
can only have one outstanding TS request at a time.
- Timestamping last segment may under report network latency of the
previous segments. Even though the doorbell is suppressed, the ring
producer counter has been incremented.
- Timestamping the first segment has the upside in that it reports
timestamps from the application's view, e.g. RTT.
- Timestamping the first segment has the downside that it may
underreport tx host network latency. It appears that we have to pick
one or the other. And possibly follow-up with a config flag to choose
behavior.
v2: Remove tests as noted by Willem de Bruijn <willemb@google.com>
Moving tests from net to net-next
v3: Update only relevant tx_flag bits as per
Willem de Bruijn <willemb@google.com>
v4: Update comments and commit message as per
Willem de Bruijn <willemb@google.com>
Fixes: ee80d1ebe5 ("udp: add udp gso")
Signed-off-by: Fred Klassen <fklassen@appneta.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iptunnel_xmit() works as a common function, also used by a udp tunnel
which doesn't have to have a tunnel device, like how TIPC works with
udp media.
In these cases, we should allow not to count pkts on dev's tstats, so
that udp tunnel can work with no tunnel device safely.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Causes crash when lifetime expires on an adress as garbage is
dereferenced soon after.
This used to look like this:
for (ifap = &ifa->ifa_dev->ifa_list;
*ifap != NULL; ifap = &(*ifap)->ifa_next) {
if (*ifap == ifa) ...
but this was changed to:
struct in_ifaddr *tmp;
ifap = &ifa->ifa_dev->ifa_list;
tmp = rtnl_dereference(*ifap);
while (tmp) {
tmp = rtnl_dereference(tmp->ifa_next); // Bogus
if (rtnl_dereference(*ifap) == ifa) {
...
ifap = &tmp->ifa_next; // Can be NULL
tmp = rtnl_dereference(*ifap); // Dereference
}
}
Remove the bogus assigment/list entry skip.
Fixes: 2638eb8b50 ("net: ipv4: provide __rcu annotation for ifa_list")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
Using a bare block cipher in non-crypto code is almost always a bad idea,
not only for security reasons (and we've seen some examples of this in
the kernel in the past), but also for performance reasons.
In the TCP fastopen case, we call into the bare AES block cipher one or
two times (depending on whether the connection is IPv4 or IPv6). On most
systems, this results in a call chain such as
crypto_cipher_encrypt_one(ctx, dst, src)
crypto_cipher_crt(tfm)->cit_encrypt_one(crypto_cipher_tfm(tfm), ...);
aesni_encrypt
kernel_fpu_begin();
aesni_enc(ctx, dst, src); // asm routine
kernel_fpu_end();
It is highly unlikely that the use of special AES instructions has a
benefit in this case, especially since we are doing the above twice
for IPv6 connections, instead of using a transform which can process
the entire input in one go.
We could switch to the cbcmac(aes) shash, which would at least get
rid of the duplicated overhead in *some* cases (i.e., today, only
arm64 has an accelerated implementation of cbcmac(aes), while x86 will
end up using the generic cbcmac template wrapping the AES-NI cipher,
which basically ends up doing exactly the above). However, in the given
context, it makes more sense to use a light-weight MAC algorithm that
is more suitable for the purpose at hand, such as SipHash.
Since the output size of SipHash already matches our chosen value for
TCP_FASTOPEN_COOKIE_SIZE, and given that it accepts arbitrary input
sizes, this greatly simplifies the code as well.
NOTE: Server farms backing a single server IP for load balancing purposes
and sharing a single fastopen key will be adversely affected by
this change unless all systems in the pool receive their kernel
upgrades at the same time.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp: make sack processing more robust
Jonathan Looney brought to our attention multiple problems
in TCP stack at the sender side.
SACK processing can be abused by malicious peers to either
cause overflows, or increase of memory usage.
First two patches fix the immediate problems.
Since the malicious peers abuse senders by advertizing a very
small MSS in their SYN or SYNACK packet, the last two
patches add a new sysctl so that admins can chose a higher
limit for MSS clamping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common functions into nf_synproxy_core.c to prepare for nftables support.
The prototypes of the functions used by {ipt, ip6t}_SYNPROXY are in the new
file nf_synproxy.h
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
tcp_tx_skb_cache_key and tcp_rx_skb_cache_key must be available
even if CONFIG_SYSCTL is not set.
Fixes: 0b7d7f6b22 ("tcp: add tcp_tx_skb_cache sysctl")
Fixes: ede61ca474 ("tcp: add tcp_rx_skb_cache sysctl")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mtu probing is enabled tcp_mtu_probing() could very well end up
with a too small MSS.
Use the new sysctl tcp_min_snd_mss to make sure MSS search
is performed in an acceptable range.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some TCP peers announce a very small MSS option in their SYN and/or
SYN/ACK messages.
This forces the stack to send packets with a very high network/cpu
overhead.
Linux has enforced a minimal value of 48. Since this value includes
the size of TCP options, and that the options can consume up to 40
bytes, this means that each segment can include only 8 bytes of payload.
In some cases, it can be useful to increase the minimal value
to a saner value.
We still let the default to 48 (TCP_MIN_SND_MSS), for compatibility
reasons.
Note that TCP_MAXSEG socket option enforces a minimal value
of (TCP_MIN_MSS). David Miller increased this minimal value
in commit c39508d6f1 ("tcp: Make TCP_MAXSEG minimum more correct.")
from 64 to 88.
We might in the future merge TCP_MIN_SND_MSS and TCP_MIN_MSS.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Looney reported that a malicious peer can force a sender
to fragment its retransmit queue into tiny skbs, inflating memory
usage and/or overflow 32bit counters.
TCP allows an application to queue up to sk_sndbuf bytes,
so we need to give some allowance for non malicious splitting
of retransmit queue.
A new SNMP counter is added to monitor how many times TCP
did not allow to split an skb if the allowance was exceeded.
Note that this counter might increase in the case applications
use SO_SNDBUF socket option to lower sk_sndbuf.
CVE-2019-11478 : tcp_fragment, prevent fragmenting a packet when the
socket is already using more than half the allowed space
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Looney reported that TCP can trigger the following crash
in tcp_shifted_skb() :
BUG_ON(tcp_skb_pcount(skb) < pcount);
This can happen if the remote peer has advertized the smallest
MSS that linux TCP accepts : 48
An skb can hold 17 fragments, and each fragment can hold 32KB
on x86, or 64KB on PowerPC.
This means that the 16bit witdh of TCP_SKB_CB(skb)->tcp_gso_segs
can overflow.
Note that tcp_sendmsg() builds skbs with less than 64KB
of payload, so this problem needs SACK to be enabled.
SACK blocks allow TCP to coalesce multiple skbs in the retransmit
queue, thus filling the 17 fragments to maximal capacity.
CVE-2019-11477 -- u16 overflow of TCP_SKB_CB(skb)->tcp_gso_segs
Fixes: 832d11c5cd ("tcp: Try to restore large SKBs while SACK processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Feng Tang reported a performance regression after introduction
of per TCP socket tx/rx caches, for TCP over loopback (netperf)
There is high chance the regression is caused by a change on
how well the 32 KB per-thread page (current->task_frag) can
be recycled, and lack of pcp caches for order-3 pages.
I could not reproduce the regression myself, cpus all being
spinning on the mm spinlocks for page allocs/freeing, regardless
of enabling or disabling the per tcp socket caches.
It seems best to disable the feature by default, and let
admins enabling it.
MM layer either needs to provide scalable order-3 pages
allocations, or could attempt a trylock on zone->lock if
the caller only attempts to get a high-order page and is
able to fallback to order-0 ones in case of pressure.
Tests run on a 56 cores host (112 hyper threads)
- 35.49% netperf [kernel.vmlinux] [k] queued_spin_lock_slowpath
- 35.49% queued_spin_lock_slowpath
- 18.18% get_page_from_freelist
- __alloc_pages_nodemask
- 18.18% alloc_pages_current
skb_page_frag_refill
sk_page_frag_refill
tcp_sendmsg_locked
tcp_sendmsg
inet_sendmsg
sock_sendmsg
__sys_sendto
__x64_sys_sendto
do_syscall_64
entry_SYSCALL_64_after_hwframe
__libc_send
+ 17.31% __free_pages_ok
+ 31.43% swapper [kernel.vmlinux] [k] intel_idle
+ 9.12% netperf [kernel.vmlinux] [k] copy_user_enhanced_fast_string
+ 6.53% netserver [kernel.vmlinux] [k] copy_user_enhanced_fast_string
+ 0.69% netserver [kernel.vmlinux] [k] queued_spin_lock_slowpath
+ 0.68% netperf [kernel.vmlinux] [k] skb_release_data
+ 0.52% netperf [kernel.vmlinux] [k] tcp_sendmsg_locked
0.46% netperf [kernel.vmlinux] [k] _raw_spin_lock_irqsave
Fixes: 472c2e07ee ("tcp: add one skb cache for tx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on rps_needed, it is safer to use a separate
static key, since we do not want to enable TCP rx_skb_cache
by default. This feature can cause huge increase of memory
usage on hosts with millions of sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was originally passed through to the VRF logic in compute_score().
But that logic has now been replaced by udp_sk_bound_dev_eq() and so
this code is no longer used or needed.
Signed-off-by: Tim Beale <timbeale@catalyst.net.nz>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally this was used by the VRF logic in compute_score(), but that
was later replaced by udp_sk_bound_dev_eq() and the parameter became
unused.
Note this change adds an 'unused variable' compiler warning that will be
removed in the next patch (I've split the removal in two to make review
slightly easier).
Signed-off-by: Tim Beale <timbeale@catalyst.net.nz>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we want to set a EDT time for the skb we want to send
via ip_send_unicast_reply(), we have to pass a new parameter
and initialize ipc.sockc.transmit_time with it.
This fixes the EDT time for ACK/RST packets sent on behalf of
a TIME_WAIT socket.
Fixes: a842fe1425 ("tcp: add optional per socket transmit delay")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multipath hash policy value of 0 isn't distributing since the outer IP
dest and src aren't varied eventhough the inner ones are. Since the flow
is on the inner ones in the case of tunneled traffic, hashing on them is
desired.
This is done mainly for IP over GRE, hence only tested for that. But
anything else supported by flow dissection should work.
v2: Use skb_flow_dissect_flow_keys() directly so that other tunneling
can be supported through flow dissection (per Nikolay Aleksandrov).
v3: Remove accidental inclusion of ports in the hash keys and clarify
the documentation (Nikolay Alexandrov).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deferred static key clean_acked_data_enabled uses the deferred
variants of dec and flush. Do the same for inc.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Adding delays to TCP flows is crucial for studying behavior
of TCP stacks, including congestion control modules.
Linux offers netem module, but it has unpractical constraints :
- Need root access to change qdisc
- Hard to setup on egress if combined with non trivial qdisc like FQ
- Single delay for all flows.
EDT (Earliest Departure Time) adoption in TCP stack allows us
to enable a per socket delay at a very small cost.
Networking tools can now establish thousands of flows, each of them
with a different delay, simulating real world conditions.
This requires FQ packet scheduler or a EDT-enabled NIC.
This patchs adds TCP_TX_DELAY socket option, to set a delay in
usec units.
unsigned int tx_delay = 10000; /* 10 msec */
setsockopt(fd, SOL_TCP, TCP_TX_DELAY, &tx_delay, sizeof(tx_delay));
Note that FQ packet scheduler limits might need some tweaking :
man tc-fq
PARAMETERS
limit
Hard limit on the real queue size. When this limit is
reached, new packets are dropped. If the value is lowered,
packets are dropped so that the new limit is met. Default
is 10000 packets.
flow_limit
Hard limit on the maximum number of packets queued per
flow. Default value is 100.
Use of TCP_TX_DELAY option will increase number of skbs in FQ qdisc,
so packets would be dropped if any of the previous limit is hit.
Use of a jump label makes this support runtime-free, for hosts
never using the option.
Also note that TSQ (TCP Small Queues) limits are slightly changed
with this patch : we need to account that skbs artificially delayed
wont stop us providind more skbs to feed the pipe (netem uses
skb_orphan_partial() for this purpose, but FQ can not use this trick)
Because of that, using big delays might very well trigger
old bugs in TSO auto defer logic and/or sndbuf limited detection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The below patch fixes an incorrect zerocopy refcnt increment when
appending with MSG_MORE to an existing zerocopy udp skb.
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt 1
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt still 1 (bar frags)
But it missed that zerocopy need not be passed at the first send. The
right test whether the uarg is newly allocated and thus has extra
refcnt 1 is not !skb, but !skb_zcopy.
send(.., MSG_MORE); // <no uarg>
send(.., MSG_ZEROCOPY); // refcnt 1
Fixes: 100f6d8e09 ("net: correct zerocopy refcnt with udp MSG_MORE")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for atomically upating a nexthop config.
When updating a nexthop, walk the lists of associated fib entries and
verify the new config is valid. Replace is done by swapping nh_info
for single nexthops - new config is applied to old nexthop struct, and
old config is moved to new nexthop struct. For nexthop groups the same
applies but for nh_group. In addition for groups the nh_parent reference
needs to be updated. The old config is released by calling __remove_nexthop
on the 'new' nexthop which now has the old config. This is done to avoid
messing around with the list_heads that track which fib entries are
using the nexthop.
After the swap of config data, bump the sequence counters for FIB entries
to invalidate any dst entries and send notifications to userspace. The
notifications include the new nexthop spec as well as any fib entries
using the updated nexthop struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be optimistic about re-using a fib_info when nexthop id is given and
the route does not use metrics. Avoids a memory allocation which in
most cases is expected to be freed anyways.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTA_NH_ID attribute to allow a user to specify a
nexthop id to use with a route. fc_nh_id is added to fib_config to
hold the value passed in the RTA_NH_ID attribute. If a nexthop id
is given, the gateway, device, encap and multipath attributes can
not be set.
Update fib_nh_match to check ids on a route delete.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 has traditionally had a single fib6_nh per fib6_info. With
nexthops we can have multiple fib6_nh associated with a fib6_info.
Add a nexthop helper to invoke a callback for each fib6_nh in a
'struct nexthop'. If the callback returns non-0, the loop is
stopped and the return value passed to the caller.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
net/ipv4/tcp_fastopen.c:75:29: warning:
symbol 'tcp_fastopen_alloc_ctx' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's better to use my kadlec@netfilter.org email address in
the source code. I might not be able to use
kadlec@blackhole.kfki.hu in the future.
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
In case autoflowlabel is in action, skb_get_hash_flowi6()
derives a non zero skb->hash to the flowlabel.
If skb->hash is zero, a flow dissection is performed.
Since all TCP skbs sent from ESTABLISH state inherit their
skb->hash from sk->sk_txhash, we better keep a copy
of sk->sk_txhash into the TIME_WAIT socket.
After this patch, ACK or RST packets sent on behalf of
a TIME_WAIT socket have the flowlabel that was previously
used by the flow.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 794200d662 ("tcp: undo cwnd on Fast Open spurious SYNACK
retransmit") may cause tcp_fastretrans_alert() to warn about pending
retransmission in Open state. This is triggered when the Fast Open
server both sends data and has spurious SYNACK retransmission during
the handshake, and the data packets were lost or reordered.
The root cause is a bit complicated:
(1) Upon receiving SYN-data: a full socket is created with
snd_una = ISN + 1 by tcp_create_openreq_child()
(2) On SYNACK timeout the server/sender enters CA_Loss state.
(3) Upon receiving the final ACK to complete the handshake, sender
does not mark FLAG_SND_UNA_ADVANCED since (1)
Sender then calls tcp_process_loss since state is CA_loss by (2)
(4) tcp_process_loss() does not invoke undo operations but instead
mark REXMIT_LOST to force retransmission
(5) tcp_rcv_synrecv_state_fastopen() calls tcp_try_undo_loss(). It
changes state to CA_Open but has positive tp->retrans_out
(6) Next ACK triggers the WARN_ON in tcp_fastretrans_alert()
The step that goes wrong is (4) where the undo operation should
have been invoked because the ACK successfully acknowledged the
SYN sequence. This fixes that by specifically checking undo
when the SYN-ACK sequence is acknowledged. Then after
tcp_process_loss() the state would be further adjusted based
in tcp_fastretrans_alert() to avoid triggering the warning in (6).
Fixes: 794200d662 ("tcp: undo cwnd on Fast Open spurious SYNACK retransmit")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix an uninitialized variable:
CC net/ipv4/fib_semantics.o
net/ipv4/fib_semantics.c: In function 'fib_check_nh_v4_gw':
net/ipv4/fib_semantics.c:1027:12: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (!tbl || err) {
^~
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuGTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykBvQCg2SG+HmDH+tlwKLT/q7jZcLMPQigAoMpt9Uuy
sxVEiFZo8ZU9v1IoRb1I
=qU++
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
Daniel Borkmann says:
====================
pull-request: bpf 2019-06-07
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix several bugs in riscv64 JIT code emission which forgot to clear high
32-bits for alu32 ops, from Björn and Luke with selftests covering all
relevant BPF alu ops from Björn and Jiong.
2) Two fixes for UDP BPF reuseport that avoid calling the program in case of
__udp6_lib_err and UDP GRO which broke reuseport_select_sock() assumption
that skb->data is pointing to transport header, from Martin.
3) Two fixes for BPF sockmap: a use-after-free from sleep in psock's backlog
workqueue, and a missing restore of sk_write_space when psock gets dropped,
from Jakub and John.
4) Fix unconnected UDP sendmsg hook API which is insufficient as-is since it
breaks standard applications like DNS if reverse NAT is not performed upon
receive, from Daniel.
5) Fix an out-of-bounds read in __bpf_skc_lookup which in case of AF_INET6
fails to verify that the length of the tuple is long enough, from Lorenz.
6) Fix libbpf's libbpf__probe_raw_btf to return an fd instead of 0/1 (for
{un,}successful probe) as that is expected to be propagated as an fd to
load_sk_storage_btf() and thus closing the wrong descriptor otherwise,
from Michal.
7) Fix bpftool's JSON output for the case when a lookup fails, from Krzesimir.
8) Minor misc fixes in docs, samples and selftests, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
Intention of cgroup bind/connect/sendmsg BPF hooks is to act transparently
to applications as also stated in original motivation in 7828f20e37 ("Merge
branch 'bpf-cgroup-bind-connect'"). When recently integrating the latter
two hooks into Cilium to enable host based load-balancing with Kubernetes,
I ran into the issue that pods couldn't start up as DNS got broken. Kubernetes
typically sets up DNS as a service and is thus subject to load-balancing.
Upon further debugging, it turns out that the cgroupv2 sendmsg BPF hooks API
is currently insufficient and thus not usable as-is for standard applications
shipped with most distros. To break down the issue we ran into with a simple
example:
# cat /etc/resolv.conf
nameserver 147.75.207.207
nameserver 147.75.207.208
For the purpose of a simple test, we set up above IPs as service IPs and
transparently redirect traffic to a different DNS backend server for that
node:
# cilium service list
ID Frontend Backend
1 147.75.207.207:53 1 => 8.8.8.8:53
2 147.75.207.208:53 1 => 8.8.8.8:53
The attached BPF program is basically selecting one of the backends if the
service IP/port matches on the cgroup hook. DNS breaks here, because the
hooks are not transparent enough to applications which have built-in msg_name
address checks:
# nslookup 1.1.1.1
;; reply from unexpected source: 8.8.8.8#53, expected 147.75.207.207#53
;; reply from unexpected source: 8.8.8.8#53, expected 147.75.207.208#53
;; reply from unexpected source: 8.8.8.8#53, expected 147.75.207.207#53
[...]
;; connection timed out; no servers could be reached
# dig 1.1.1.1
;; reply from unexpected source: 8.8.8.8#53, expected 147.75.207.207#53
;; reply from unexpected source: 8.8.8.8#53, expected 147.75.207.208#53
;; reply from unexpected source: 8.8.8.8#53, expected 147.75.207.207#53
[...]
; <<>> DiG 9.11.3-1ubuntu1.7-Ubuntu <<>> 1.1.1.1
;; global options: +cmd
;; connection timed out; no servers could be reached
For comparison, if none of the service IPs is used, and we tell nslookup
to use 8.8.8.8 directly it works just fine, of course:
# nslookup 1.1.1.1 8.8.8.8
1.1.1.1.in-addr.arpa name = one.one.one.one.
In order to fix this and thus act more transparent to the application,
this needs reverse translation on recvmsg() side. A minimal fix for this
API is to add similar recvmsg() hooks behind the BPF cgroups static key
such that the program can track state and replace the current sockaddr_in{,6}
with the original service IP. From BPF side, this basically tracks the
service tuple plus socket cookie in an LRU map where the reverse NAT can
then be retrieved via map value as one example. Side-note: the BPF cgroups
static key should be converted to a per-hook static key in future.
Same example after this fix:
# cilium service list
ID Frontend Backend
1 147.75.207.207:53 1 => 8.8.8.8:53
2 147.75.207.208:53 1 => 8.8.8.8:53
Lookups work fine now:
# nslookup 1.1.1.1
1.1.1.1.in-addr.arpa name = one.one.one.one.
Authoritative answers can be found from:
# dig 1.1.1.1
; <<>> DiG 9.11.3-1ubuntu1.7-Ubuntu <<>> 1.1.1.1
;; global options: +cmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NXDOMAIN, id: 51550
;; flags: qr rd ra ad; QUERY: 1, ANSWER: 0, AUTHORITY: 1, ADDITIONAL: 1
;; OPT PSEUDOSECTION:
; EDNS: version: 0, flags:; udp: 512
;; QUESTION SECTION:
;1.1.1.1. IN A
;; AUTHORITY SECTION:
. 23426 IN SOA a.root-servers.net. nstld.verisign-grs.com. 2019052001 1800 900 604800 86400
;; Query time: 17 msec
;; SERVER: 147.75.207.207#53(147.75.207.207)
;; WHEN: Tue May 21 12:59:38 UTC 2019
;; MSG SIZE rcvd: 111
And from an actual packet level it shows that we're using the back end
server when talking via 147.75.207.20{7,8} front end:
# tcpdump -i any udp
[...]
12:59:52.698732 IP foo.42011 > google-public-dns-a.google.com.domain: 18803+ PTR? 1.1.1.1.in-addr.arpa. (38)
12:59:52.698735 IP foo.42011 > google-public-dns-a.google.com.domain: 18803+ PTR? 1.1.1.1.in-addr.arpa. (38)
12:59:52.701208 IP google-public-dns-a.google.com.domain > foo.42011: 18803 1/0/0 PTR one.one.one.one. (67)
12:59:52.701208 IP google-public-dns-a.google.com.domain > foo.42011: 18803 1/0/0 PTR one.one.one.one. (67)
[...]
In order to be flexible and to have same semantics as in sendmsg BPF
programs, we only allow return codes in [1,1] range. In the sendmsg case
the program is called if msg->msg_name is present which can be the case
in both, connected and unconnected UDP.
The former only relies on the sockaddr_in{,6} passed via connect(2) if
passed msg->msg_name was NULL. Therefore, on recvmsg side, we act in similar
way to call into the BPF program whenever a non-NULL msg->msg_name was
passed independent of sk->sk_state being TCP_ESTABLISHED or not. Note
that for TCP case, the msg->msg_name is ignored in the regular recvmsg
path and therefore not relevant.
For the case of ip{,v6}_recv_error() paths, picked up via MSG_ERRQUEUE,
the hook is not called. This is intentional as it aligns with the same
semantics as in case of TCP cgroup BPF hooks right now. This might be
better addressed in future through a different bpf_attach_type such
that this case can be distinguished from the regular recvmsg paths,
for example.
Fixes: 1cedee13d2 ("bpf: Hooks for sys_sendmsg")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martynas Pumputis <m@lambda.lt>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Only a handful of xfrm_types exist, no need to have 512 pointers for them.
Reduces size of afinfo struct from 4k to 120 bytes on 64bit platforms.
Also, the unregister function doesn't need to return an error, no single
caller does anything useful with it.
Just place a WARN_ON() where needed instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm_prepare_input needs to lookup the state afinfo backend again to fetch
the address family ethernet protocol value.
There are only two address families, so a switch statement is simpler.
While at it, use u8 for family and proto and remove the owner member --
its not used anywhere.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
small cleanup: "struct request_sock_queue *queue" parameter of reqsk_queue_unlink
func is never used in the func, so we can remove it.
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the topo:
h1 ---| rp1 |
| route rp3 |--- h3 (192.168.200.1)
h2 ---| rp2 |
If rp1 bc_forwarding is set while rp2 bc_forwarding is not, after
doing "ping 192.168.200.255" on h1, then ping 192.168.200.255 on
h2, and the packets can still be forwared.
This issue was caused by the input route cache. It should only do
the cache for either bc forwarding or local delivery. Otherwise,
local delivery can use the route cache for bc forwarding of other
interfaces.
This patch is to fix it by not doing cache for local delivery if
all.bc_forwarding is enabled.
Note that we don't fix it by checking route cache local flag after
rt_cache_valid() in "local_input:" and "ip_mkroute_input", as the
common route code shouldn't be touched for bc_forwarding.
Fixes: 5cbf777cfd ("route: add support for directed broadcast forwarding")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already calls unlikely(), so this extra unlikely() call
around IS_ERR() is not needed.
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 21 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141334.228102212@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one implementation of this function; just call it directly.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>