Pull irq updates from Thomas Gleixner:
"Two patches from the irq departement:
- a simple fix to make dummy_irq_chip usable for wakeup scenarios
- removal of the gic arch_extn hackery. Now that all users are
converted we really want to get rid of the interface so people wont
come up with new use cases"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: gic: Drop support for gic_arch_extn
genirq: Set IRQCHIP_SKIP_SET_WAKE flag for dummy_irq_chip
Now that the users of gic_arch_extn have been fixed, drop the
"feature" for good. This leads to the removal of some now useless
locking.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This series introduces preliminary ACPI 5.1 support to the arm64 kernel
using the "hardware reduced" profile. We don't support any peripherals
yet, so it's fairly limited in scope:
- Memory init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVNOC2AAoJELescNyEwWM08dIH/1Pn5xa04wwNDn0MOpbuQMk2
kHM7hx69fbXflTJpnZRVyFBjRxxr5qilA7rljAFLnFeF8Fcll/s5VNy7ElHKLISq
CB0ywgUfOd/sFJH57rcc67pC1b/XuqTbE1u1NFwvp2R3j1kGAEJWNA6SyxIP4bbc
NO5jScx0lQOJ3rrPAXBW8qlGkeUk7TPOQJtMrpftNXlFLFrR63rPaEmMZ9dWepBF
aRE4GXPvyUhpyv5o9RvlN5l8bQttiRJ3f9QjyG7NYhX0PXH3DyvGUzYlk2IoZtID
v3ssCQH3uRsAZHIBhaTyNqFnUIaDR825bvGqyG/tj2Dt3kQZiF+QrfnU5D9TuMw=
=zLJn
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
- Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IPgJ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.1-3' of git://git.infradead.org/users/jcooper/linux into irq/core
irqchip core change for v4.1 (round 3) from Jason Cooper
Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
We add new functions to start and stop the GIC counter since there are no
guarantees the counter will be running after a CPU reset. The GIC counter
is stopped by setting the 29th bit on the GIC Config register and it is
started by clearing that bit.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a function to the MIPS GIC driver for retrieving the Fast Debug
Channel (FDC) interrupt number, similar to the existing ones for the
timer and perf counter interrupts. This will be used by platform
implementations of get_c0_fdc_int() if a GIC is present.
A workaround exists for interAptiv and proAptiv which claim to be able
to route the FDC interrupt but don't seem to be able to in practice (at
least on Malta).
[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9142/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add missing VPE_PEND, VPE_RMASK and VPE_SMASK definitions for the local
FDC interrupt.
These local interrupt definitions aren't directly used, but if they
exist they should be complete.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9127/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We add new functions to start and stop the GIC counter since there are no
guarantees the counter will be running after a CPU reset. The GIC counter
is stopped by setting the 29th bit on the GIC Config register and it is
started by clearing that bit.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Link: https://lkml.kernel.org/r/1427113923-9840-2-git-send-email-markos.chandras@imgtec.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
If the ITS or the redistributors report their shareability as zero,
then it is important to make sure they will no generate any cacheable
traffic, as this is unlikely to produce the expected result.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ITS driver sometime mixes up the use of GICR_PROPBASE bitfields
for the GICR_PENDBASE register, and GITS_BASER for GICR_CBASE.
This does not lead to any observable bug because similar bits are
at the same location, but this just make the code even harder to
understand...
This patch provides the required #defines and fixes the mixup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
ACPI kernel uses MADT table for proper GIC initialization. It needs to
parse GIC related subtables, collect CPU interface and distributor
addresses and call driver initialization function (which is hardware
abstraction agnostic). In a similar way, FDT initialize GICv1/2.
NOTE: This commit allow to initialize GICv1/2 basic functionality.
While now simple GICv2 init call is used, any further GIC features
require generic infrastructure for proper ACPI irqchip initialization.
That mechanism and stacked irqdomains to support GICv2 MSI/virtualization
extension, GICv3/4 and its ITS are considered as next steps.
CC: Jason Cooper <jason@lakedaemon.net>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A common use of gic_arch_extn is to set up additional flags
to the GIC irqchip. It looks like a benign enough hack that
doesn't really require the users of that feature to be converted
to stacked domains.
Add a gic_set_irqchip_flags() function that platform code can
call instead of using the dreaded gic_arch_extn.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088737-15817-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The only user of the so called "routable domain" functionality
now being fixed, let's clean up the GIC.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Support for the TI crossbar used on the DRA7 family of chips
is implemented as an ugly hack on the side of the GIC.
Converting it to stacked domains makes it slightly more
palatable, as it results in a cleanup.
Unfortunately, as the DT bindings failed to acknowledge the
fact that this is actually yet another interrupt controller
(the third, actually), we have yet another breakage. Oh well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Define macros for GITS_CTLR fields to avoid using magic numbers.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-11-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ITS table allocator is only allocating a single page per table.
This works fine for most things, but leads to silent lack of
interrupt delivery if we end-up with a device that has an ID that is
out of the range defined by a single page of memory. Even worse, depending
on the page size, behaviour changes, which is not a very good experience.
A solution is actually to allocate memory for the full range of ID that
the ITS supports. A massive waste memory wise, but at least a safe bet.
Tested on a Phytium SoC.
Tested-by: Chen Baozi <chenbaozi@kylinos.com.cn>
Acked-by: Chen Baozi <chenbaozi@kylinos.com.cn>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
Pull irqchip updates from Ingo Molnar:
"Various irqchip driver updates, plus a genirq core update that allows
the initial spreading of irqs amonst CPUs without having to do it from
user-space"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix null pointer reference in irq_set_affinity_hint()
irqchip: gic: Allow interrupt level to be set for PPIs
irqchip: mips-gic: Handle pending interrupts once in __gic_irq_dispatch()
irqchip: Conexant CX92755 interrupts controller driver
irqchip: Devicetree: document Conexant Digicolor irq binding
irqchip: omap-intc: Remove unused legacy interface for omap2
irqchip: omap-intc: Fix support for dm814 and dm816
irqchip: mtk-sysirq: Get irq number from register resource size
irqchip: renesas-intc-irqpin: r8a7779 IRLM setup support
genirq: Set initial affinity in irq_set_affinity_hint()
The cevt-r4k driver used to call into the GIC driver to find whether the
timer was pending, but only with External Interrupt Controller (EIC)
mode, where the Cause.IP bits can't be used as they encode the interrupt
priority level (Cause.RIPL) instead.
However commit e9de688dac ("irqchip: mips-gic: Support local
interrupts") changed the condition from cpu_has_veic to gic_present.
This fails on cores such as P5600 which have a GIC but the local
interrupts aren't routable by the GIC, causing c0_compare_int_usable()
to consider the interrupt unusable so r4k_clockevent_init() fails.
The previous behaviour, added in commit 98b67c37db ("MIPS: Add EIC
support for GIC."), wasn't really correct either as far as I can tell,
since P5600 apparently supports EIC mode too, and in any case the use of
Cause.TI with r2 should have been sufficient anyway since commit
010c108d7a ("MIPS: PowerTV: Fix support for timer interrupts with > 64
external IRQs").
Therefore drop the call into the gic driver altogether, and add a
comment in c0_compare_int_pending() to clarify that Cause.TI does get
checked since MIPS r2.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: e9de688dac ("irqchip: mips-gic: Support local interrupts")
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven J. Hill <steven.hill@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9077/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nowadays omap2 is booting in device tree only mode so there is no
need to keep the legacy interface around for omap2_init_irq().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1421187806-6804-3-git-send-email-tony@atomide.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On dm81xx we have 128 interrupts like am33xx has. Let's add
compatible flags for dm814x and dm816x, and document the
existing binding.
As the dm81xx are booting in device tree only mode, we can now
also remove ti81xx_init_irq() legacy function.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1421187806-6804-2-git-send-email-tony@atomide.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The gic_send_sgi() function used hardcoded bit shift values to
generate the ICC_SGI1R_EL1 register value.
Replace this with symbolic names to allow reusing them later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
With everything separated and prepared, we implement a model of a
GICv3 distributor and redistributors by using the existing framework
to provide handler functions for each register group.
Currently we limit the emulation to a model enforcing a single
security state, with SRE==1 (forcing system register access) and
ARE==1 (allowing more than 8 VCPUs).
We share some of the functions provided for GICv2 emulation, but take
the different ways of addressing (v)CPUs into account.
Save and restore is currently not implemented.
Similar to the split-off of the GICv2 specific code, the new emulation
code goes into a new file (vgic-v3-emul.c).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Pull irq domain ARM updates from Thomas Gleixner:
"This set of changes make use of hierarchical irqdomains to provide:
- MSI/ITS support for GICv3
- MSI support for GICv2m
- Interrupt polarity extender for GICv1
Marc has come more cleanups for the existing extension hooks of GIC in
the pipeline, but they are going to be 3.20 material"
* 'irq-irqdomain-arm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
irqchip: gicv3-its: Fix ITT allocation
irqchip: gicv3-its: Move some alloc/free code to activate/deactivate
irqchip: gicv3-its: Fix domain free in multi-MSI case
irqchip: gic: Remove warning by including linux/irqdomain.h
irqchip: gic-v2m: Add DT bindings for GICv2m
irqchip: gic-v2m: Add support for ARM GICv2m MSI(-X) doorbell
irqchip: mtk-sysirq: dt-bindings: Add bindings for mediatek sysirq
irqchip: mtk-sysirq: Add sysirq interrupt polarity support
irqchip: gic: Support hierarchy irq domain.
irqchip: GICv3: Binding updates for ITS
irqchip: GICv3: ITS: enable compilation of the ITS driver
irqchip: GICv3: ITS: plug ITS init into main GICv3 code
irqchip: GICv3: ITS: DT probing and initialization
irqchip: GICv3: ITS: MSI support
irqchip: GICv3: ITS: device allocation and configuration
irqchip: GICv3: ITS: tables allocators
irqchip: GICv3: ITS: LPI allocator
irqchip: GICv3: ITS: irqchip implementation
irqchip: GICv3: ITS command queue
irqchip: GICv3: rework redistributor structure
...
Commit
853a33ce69 irqchip: gic-v2m: Add support for ARM GICv2m MSI(-X) doorbell
Introduced a series of warnings when building ARM multi_v7_defconfig:
include/linux/irqchip/arm-gic.h:109:53: warning: its scope is only this definition or declaration, which is probably not what you want
In file included from arch/arm/mach-ux500/pm.c:13:0:
include/linux/irqchip/arm-gic.h:109:53: warning: 'struct irq_domain' declared inside parameter list
int gicv2m_of_init(struct device_node *node, struct irq_domain *parent);
^
Fix this by adding the proper include.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
[ jac merged much more correct version from Marc into this patch ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Link: https://lkml.kernel.org/r/1417170975-1163-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
ARM GICv2m specification extends GICv2 to support MSI(-X) with
a new register frame. This allows a GICv2 based system to support
MSI with minimal changes.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
[maz: converted the driver to use stacked irq domains,
updated changelog]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416941243-7181-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
As the ITS is always a subsystem if GICv3, its probing/init is
driven by the main GICv3 code.
Plug that code in (guarded by a config option).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416839720-18400-12-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ITS is configured through a number commands that the driver
issues to the HW using a memory-based circular buffer.
This patch implements the subset of commands that are required
for Linux.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416839720-18400-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The basic GICv3 driver has almost no use for the redistributor
(other than the basic per-CPU interrupts), but the ITS needs
a lot more from them.
As such, rework the set of data structures. The behaviour of the
GICv3 driver is otherwise unaffected.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416839720-18400-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There's no reason for gic_frequency to be global any more and it
certainly doesn't belong in the GIC irqchip driver, so move it to
the GIC clocksource driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8137/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that the MIPS GIC irqchip lives in drivers/irqchip/, move
its header over to include/linux/irqchip/.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8129/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- a cleanup series to get rid of mindlessly copied code.
- another bunch of new pointlessly different interrupt chip drivers.
Adding homebrewn irq chips (and timers) to SoCs must provide a
value add which is beyond the imagination of mere mortals.
- the usual SoC irq controller updates, IOW my second cat herding
project"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
irqchip: gic-v3: Implement CPU PM notifier
irqchip: gic-v3: Refactor gic_enable_redist to support both enabling and disabling
irqchip: renesas-intc-irqpin: Add minimal runtime PM support
irqchip: renesas-intc-irqpin: Add helper variable dev = &pdev->dev
irqchip: atmel-aic5: Add sama5d4 support
irqchip: atmel-aic5: The sama5d3 has 48 IRQs
Documentation: bcm7120-l2: Add Broadcom BCM7120-style L2 binding
irqchip: bcm7120-l2: Add Broadcom BCM7120-style Level 2 interrupt controller
irqchip: renesas-irqc: Add binding docs for new R-Car Gen2 SoCs
irqchip: renesas-irqc: Add DT binding documentation
irqchip: renesas-intc-irqpin: Document SoC-specific bindings
openrisc: Get rid of handle_IRQ
arm64: Get rid of handle_IRQ
ARM: omap2: irq: Convert to handle_domain_irq
ARM: imx: tzic: Convert to handle_domain_irq
ARM: imx: avic: Convert to handle_domain_irq
irqchip: or1k-pic: Convert to handle_domain_irq
irqchip: atmel-aic5: Convert to handle_domain_irq
irqchip: atmel-aic: Convert to handle_domain_irq
irqchip: gic-v3: Convert to handle_domain_irq
...
OMAP INTC irqchip driver will be moved under
drivers/irqchip/ soon but we still have a dependency
with mach-omap2 when it comes to idle functions.
In order to make it easy to share those function
prototypes with OMAP PM code, we introduce this new
header.
To avoid modifying several board-files and some of
the PM-related code, we just include the new header
from common.h which was already included by all
users of IRQ-related PM code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change is made to preserve the GIC v2 bypass bits in the
GIC_CPU_CTRL register (also known as the GICC_CTLR register in spec).
This code will preserve all bits configured by the bootloader regarding
v2 bypass group bits. In the X-Gene platform, the bypass functionality
is not used and bypass bits should not be changed by the kernel gic
code as it could lead to incorrect behavior.
Signed-off-by: Feng Kan <fkan@apm.com>
Reviewed-by: Vinayak Kale <vkale@apm.com>
Reviewed-by: Anup Patel <apatel@apm.com>
Link: https://lkml.kernel.org/r/1406757419-18729-3-git-send-email-fkan@apm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is to cleanup some hex numbers used in the code and replace
them with defines to make the code cleaner.
Signed-off-by: Feng Kan <fkan@apm.com>
Reviewed-by: Anup Patel <apatel@apm.com>
Link: https://lkml.kernel.org/r/1406757419-18729-2-git-send-email-fkan@apm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull irq updates from Thomas Gleixner:
"Nothing spectacular from the irq department this time:
- overhaul of the crossbar chip driver
- overhaul of the spear shirq chip driver
- support for the atmel-aic chip
- code move from arch to drivers
- the usual tiny fixlets
- two reverts worth to mention which undo the too simple attempt of
supporting wakeup interrupts on shared interrupt lines"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
Revert "irq: Warn when shared interrupts do not match on NO_SUSPEND"
Revert "PM / sleep / irq: Do not suspend wakeup interrupts"
irq: Warn when shared interrupts do not match on NO_SUSPEND
irqchip: atmel-aic: Define irq fixups for atmel SoCs
irqchip: atmel-aic: Implement RTC irq fixup
irqchip: atmel-aic: Add irq fixup infrastructure
irqchip: atmel-aic: Add atmel AIC/AIC5 drivers
irqchip: atmel-aic: Move binding doc to interrupt-controller directory
genirq: generic chip: Export irq_map_generic_chip function
PM / sleep / irq: Do not suspend wakeup interrupts
irqchip: or1k-pic: Migrate from arch/openrisc/
irqchip: crossbar: Allow for quirky hardware with direct hardwiring of GIC
documentation: dt: omap: crossbar: Add description for interrupt consumer
irqchip: crossbar: Introduce centralized check for crossbar write
irqchip: crossbar: Introduce ti, max-crossbar-sources to identify valid crossbar mapping
irqchip: crossbar: Add kerneldoc for crossbar_domain_unmap callback
irqchip: crossbar: Set cb pointer to null in case of error
irqchip: crossbar: Change the goto naming
irqchip: crossbar: Return proper error value
irqchip: crossbar: Fix kerneldoc warning
...
GICv3 introduces new system registers accessible with the full msr/mrs
syntax (e.g. mrs x0, Sop0_op1_CRm_CRn_op2). However, only recent
binutils understand the new syntax. This patch introduces msr_s/mrs_s
assembly macros which generate the equivalent instructions above and
converts the existing GICv3 code (both drivers/irqchip/ and
arch/arm64/kernel/).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Olof Johansson <olof@lixom.net>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
The Generic Interrupt Controller (version 3) offers services that are
similar to GICv2, with a number of additional features:
- Affinity routing based on the CPU MPIDR (ARE)
- System register for the CPU interfaces (SRE)
- Support for more that 8 CPUs
- Locality-specific Peripheral Interrupts (LPIs)
- Interrupt Translation Services (ITS)
This patch adds preliminary support for GICv3 with ARE and SRE,
non-secure mode only. It relies on higher exception levels to grant ARE
and SRE access.
Support for LPI and ITS will be added at a later time.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Zi Shen Lim <zlim@broadcom.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Reviewed-by: Yun Wu <wuyun.wu@huawei.com>
Reviewed-by: Zhen Lei <thunder.leizhen@huawei.com>
Tested-by: Tirumalesh Chalamarla<tchalamarla@cavium.com>
Tested-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Acked-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lkml.kernel.org/r/1404140510-5382-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
No point in having them in a separate header file. Make the init
functions static.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.038658058@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Bit[9:0] is interrupt ID field in GICC_IAR. Bit[12:10] is CPU ID field,
and others are reserved.
So we should use GICC_IAR_INT_ID_MASK to get interrupt ID. It's not a good way
to use ~0x1c00 (CPU ID field) to get interrupt ID.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Link: https://lkml.kernel.org/r/1399795571-17231-3-git-send-email-haojian.zhuang@linaro.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Looks like people wanted these merged via the omap tree as it's
the only user for the GIC crossbar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=MLEE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/crossbar-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Merge OMAP crossbar support from Tony Lindgren:
Add support for GIC crossbar that routes interrupts on newer omaps.
Looks like people wanted these merged via the omap tree as it's
the only user for the GIC crossbar.
* tag 'omap-for-v3.15/crossbar-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA: Enable Crossbar IP support for DRA7XX
ARM: OMAP4+: Correct Wakeup-gen code to use physical irq number
DRIVERS: IRQCHIP: CROSSBAR: Add support for Crossbar IP
DRIVERS: IRQCHIP: IRQ-GIC: Add support for routable irqs
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for a VIC to be cascaded off another IRQ.
On the Integrator/AP logical module IM-PD1 there is a VIC
cascaded off the central FPGA IRQ controller so this is
needed for that to work out.
In order for the plug-in board to be able to register all
the devices with their IRQs relative to the offset of the
base obtained for the cascaded VIC, the base IRQ number
is passed back to the caller.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some socs have a large number of interrupts requests to service
the needs of its many peripherals and subsystems. All of the
interrupt lines from the subsystems are not needed at the same
time, so they have to be muxed to the irq-controller appropriately.
In such places a interrupt controllers are preceded by an CROSSBAR
that provides flexibility in muxing the device requests to the controller
inputs.
This driver takes care a allocating a free irq and then configuring the
crossbar IP as a part of the mpu's irqchip callbacks. crossbar_init should
be called right before the irqchip_init, so that it is setup to handle the
irqchip callbacks.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Kumar Gala <galak@codeaurora.org> (for DT binding portion)
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds