We need to check whether pte is present in follow_huge_addr() and
properly return NULL if mapping is not present. Also use READ_ONCE
when dereferencing pte_t address.
Without this patch, we may wrongly return a zero pfn page in
follow_huge_addr().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Serialize against find_linux_pte_or_hugepte() which does lock-less
lookup in page tables with local interrupts disabled. For huge pages it
casts pmd_t to pte_t. Since the format of pte_t is different from pmd_t
we want to prevent transit from pmd pointing to page table to pmd
pointing to huge page (and back) while interrupts are disabled. We
clear pmd to possibly replace it with page table pointer in different
code paths. So make sure we wait for the parallel
find_linux_pte_or_hugepage() to finish.
Without this patch, a find_linux_pte_or_hugepte() running in parallel to
__split_huge_zero_page_pmd() or do_huge_pmd_wp_page_fallback() or
zap_huge_pmd() can run into the above issue. With
__split_huge_zero_page_pmd() and do_huge_pmd_wp_page_fallback() we clear
the hugepage pte before inserting the pmd entry with a regular pgtable
address. Such a clear need to wait for the parallel
find_linux_pte_or_hugepte() to finish.
With zap_huge_pmd(), we can run into issues, with a hugepage pte getting
zapped due to a MADV_DONTNEED while other cpu fault it in as small
pages.
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix a few AM43xx problems: add the VPFE hwmod data, which removes some
warnings; and fix the IP block hardreset implementation.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.1-rc/20150508130543/
Note that I do not have an AM43xx board in the testbed, and thus
cannot test on that platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jonz
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.1/fixes
ARM: OMAP2+: first set of hwmod fixes for v4.1-rc
Fix a few AM43xx problems: add the VPFE hwmod data, which removes some
warnings; and fix the IP block hardreset implementation.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.1-rc/20150508130543/
Note that I do not have an AM43xx board in the testbed, and thus
cannot test on that platform.
With recent changes to use determine_rate, the comparison of two
clocks won't work without clk_is_match that does __clk_get_hw
on the clocks first.
As we've been unconditionally already calling clk_set_parent
already because of the bogus comparison, let's just remove the
check as suggested by Stephen Boyd <sboyd@codeaurora.org>.
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull crypto fixes from Herbert Xu:
"This fixes a the implementation of CRC32 on arm64 where it incorrectly
applied negation on the result.
It also fixes the arm64 implementations of SHA/SHA256 where in some
cases it may end up finalising the result twice"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm64/sha2-ce - prevent asm code finalization in final() path
crypto: arm64/sha1-ce - prevent asm code finalization in final() path
crypto: arm64/crc32 - bring in line with generic CRC32
KVM may turn a user page to a kernel page when kernel writes a readonly
user page if CR0.WP = 1. This shadow page entry will be reused after
SMAP is enabled so that kernel is allowed to access this user page
Fix it by setting SMAP && !CR0.WP into shadow page's role and reset mmu
once CR4.SMAP is updated
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
smep_andnot_wp is initialized in kvm_init_shadow_mmu and shadow pages
should not be reused for different values of it. Thus, it has to be
added to the mask in kvm_mmu_pte_write.
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Current permission check assumes that RSVD bit in PFEC is always zero,
however, it is not true since MMIO #PF will use it to quickly identify
MMIO access
Fix it by clearing the bit if walking guest page table is needed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Si5351 clock generator on CuBox uses XTAL as clock reference, name the
clock phandle accordingly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Change HOST_EXTRACFLAGS to include arch/x86/include/uapi along
with include/uapi.
This looks more consistent, and this fixes "make bzImage" on my
old distro which doesn't have asm/bitsperlong.h in /usr/include/.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 6f121e548f ("x86, vdso: Reimplement vdso.so preparation in build-time C")
Link: http://lkml.kernel.org/r/1431332153-18566-6-git-send-email-bp@alien8.de
Link: http://lkml.kernel.org/r/20150507165835.GB18652@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ARM JIT code emits "ldr rX, [pc, #offset]" to access the literal
pool. #offset maximum value is 4095 and if the generated code is too
large, the #offset value can overflow and not point to the expected
slot in the literal pool. Additionally, when overflow occurs, bits of
the overflow can end up changing the destination register of the ldr
instruction.
Fix that by detecting the overflow in imm_offset() and setting a flag
that is checked for each BPF instructions converted in
build_body(). As of now it can only be detected in the second pass. As
a result the second build_body() call can now fail, so add the
corresponding cleanup code in that case.
Using multiple literal pools in the JITed code is going to require
lots of intrusive changes to the JIT code (which would better be done
as a feature instead of fix), just delegating to the kernel BPF
interpreter in that case is a more straight forward, minimal fix and
easy to backport.
Fixes: ddecdfcea0 ("ARM: 7259/3: net: JIT compiler for packet filters")
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In that case, emit_udiv() will be called with rn == ARM_R0 (r_scratch)
and loading rm first into ARM_R0 will result in jit_udiv() function
being called the same dividend and divisor. Fix that by loading rn
first into ARM_R1 and then rm into ARM_R0.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Cc: <stable@vger.kernel.org> # v3.13+
Fixes: aee636c480 (bpf: do not use reciprocal divide)
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM fixes from Russell King:
"A set of ARM fixes:
- fix an off-by-one error in the iommu DMA ops, which caused errors
with a 4GiB size.
- remove comments mentioning the non-existent CONFIG_CPU_ARM1020_CPU_IDLE
macro.
- remove useless CONFIG_CPU_ICACHE_STREAMING_DISABLE blocks, where
this symbol never appeared in any Kconfig.
- fix Feroceon code to cope with a previous change correctly (it
incorrectly left an additional word in an assembly structure
definition)
- avoid a misleading IRQ affinity warning in the ARM PMU code for
IRQs which are already affine to their CPUs.
- fix the node name printed in the IRQ affinity warning"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8352/1: perf: Fix the pmu node name in warning message
ARM: 8351/1: perf: don't warn about missing interrupt-affinity property for PPIs
ARM: 8350/1: proc-feroceon: Fix feroceon_proc_info macro
ARM: 8349/1: arch/arm/mm/proc-arm925.S: remove dead #ifdef block
ARM: 8348/1: remove comments on CPU_ARM1020_CPU_IDLE
ARM: 8347/1: dma-mapping: fix off-by-one check in arm_setup_iommu_dma_ops
- fixes commit ea08de16eb ("ARM: dts: Add DISP1 power
domain for exynos5420") which causes 'unhandled fault:
imprecise external abort' error when PD turned off.
: make DP a consumer of DISP1 power domain
- fixes 's3c-rtc' probe failure on Odriod-X2/U2/U3 boards.
: add 'rtc_src' clock to rtc node for source clock of rtc
- fixes typo for 'cpu-crit-0' trip point on exynos5420/5440
- fixes S2R failure on exynos5250-snow due to card power of
Marvell WiFi driver (suspend/resume)
: add keep-power-in-susped to WiFi SDIO node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YBxq
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
Pull samsung fixes from Kukjin Kim:
"Here is Samsung fixes for v4.1. Since I've missed to send this via
arm-soc tree before v4.1-rc3, so I'm sending this to you directly
- fix commit ea08de16eb ("ARM: dts: Add DISP1 power domain for
exynos5420") which causes 'unhandled fault: imprecise external
abort' error when PD turned off. ("make DP a consumer of DISP1
power domain")
- fix 's3c-rtc' probe failure on Odriod-X2/U2/U3 boards ("add
'rtc_src' clock to rtc node for source clock of rtc")
- fix typo for 'cpu-crit-0' trip point on exynos5420/5440
- fix S2R failure on exynos5250-snow due to card power of Marvell
WiFi driver (suspend/resume) ("add keep-power-in-susped to WiFi
SDIO node")"
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
This fixes a regression introduced in commit 25fedfca94, "KVM: PPC:
Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu", which
leads to a user-triggerable oops.
In the case where we try to run a vcore on a physical core that is
not in single-threaded mode, or the vcore has too many threads for
the physical core, we iterate the list of runnable vcpus to make
each one return an EBUSY error to userspace. Since this involves
taking each vcpu off the runnable_threads list for the vcore, we
need to use list_for_each_entry_safe rather than list_for_each_entry
to traverse the list. Otherwise the kernel will crash with an oops
message like this:
Unable to handle kernel paging request for data at address 0x000fff88
Faulting instruction address: 0xd00000001e635dc8
Oops: Kernel access of bad area, sig: 11 [#2]
SMP NR_CPUS=1024 NUMA PowerNV
...
CPU: 48 PID: 91256 Comm: qemu-system-ppc Tainted: G D 3.18.0 #1
task: c00000274e507500 ti: c0000027d1924000 task.ti: c0000027d1924000
NIP: d00000001e635dc8 LR: d00000001e635df8 CTR: c00000000011ba50
REGS: c0000027d19275b0 TRAP: 0300 Tainted: G D (3.18.0)
MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 22002824 XER: 00000000
CFAR: c000000000008468 DAR: 00000000000fff88 DSISR: 40000000 SOFTE: 1
GPR00: d00000001e635df8 c0000027d1927830 d00000001e64c850 0000000000000001
GPR04: 0000000000000001 0000000000000001 0000000000000000 0000000000000000
GPR08: 0000000000200200 0000000000000000 0000000000000000 d00000001e63e588
GPR12: 0000000000002200 c000000007dbc800 c000000fc7800000 000000000000000a
GPR16: fffffffffffffffc c000000fd5439690 c000000fc7801c98 0000000000000001
GPR20: 0000000000000003 c0000027d1927aa8 c000000fd543b348 c000000fd543b350
GPR24: 0000000000000000 c000000fa57f0000 0000000000000030 0000000000000000
GPR28: fffffffffffffff0 c000000fd543b328 00000000000fe468 c000000fd543b300
NIP [d00000001e635dc8] kvmppc_run_core+0x198/0x17c0 [kvm_hv]
LR [d00000001e635df8] kvmppc_run_core+0x1c8/0x17c0 [kvm_hv]
Call Trace:
[c0000027d1927830] [d00000001e635df8] kvmppc_run_core+0x1c8/0x17c0 [kvm_hv] (unreliable)
[c0000027d1927a30] [d00000001e638350] kvmppc_vcpu_run_hv+0x5b0/0xdd0 [kvm_hv]
[c0000027d1927b70] [d00000001e510504] kvmppc_vcpu_run+0x44/0x60 [kvm]
[c0000027d1927ba0] [d00000001e50d4a4] kvm_arch_vcpu_ioctl_run+0x64/0x170 [kvm]
[c0000027d1927be0] [d00000001e504be8] kvm_vcpu_ioctl+0x5e8/0x7a0 [kvm]
[c0000027d1927d40] [c0000000002d6720] do_vfs_ioctl+0x490/0x780
[c0000027d1927de0] [c0000000002d6ae4] SyS_ioctl+0xd4/0xf0
[c0000027d1927e30] [c000000000009358] syscall_exit+0x0/0x98
Instruction dump:
60000000 60420000 387e1b30 38800003 38a00001 38c00000 480087d9 e8410018
ebde1c98 7fbdf040 3bdee368 419e0048 <813e1b20> 939e1b18 2f890001 409effcc
---[ end trace 8cdf50251cca6680 ]---
Fixes: 25fedfca94
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A few patches have come up since the merge window. The largest one is a
rewrite of the PXA lubbock/mainstone IRQ handling. This was already
broken in 2011 by a change to the GPIO code and only noticed now.
The other changes contained here are:
MAINTAINERS file updates:
- Ray Jui and Scott Branden are now co-maintainers for some of the
mach-bcm chips, while Christian Daudt and Marc Carino have stepped
down.
- Andrew Victor is no longer maintaining at91. Instead, Alexandre
Belloni now becomes an official maintainer, after having done a
bulk of the work for a while.
- Baruch Siach, who added the mach-digicolor platform in 4.1
is now listed as maintainer
- The git URL for mach-socfpga has changed
Bug fixes:
- Three bug fixes for new rockchip rk3288 code
- A regression fix to make SD card support work on certain ux500
boards
- multiple smaller dts fixes for imx, omap, mvebu, and shmobile
- a regression fiix for omap3 power consumption
- a fix for regression in the ARM CCI bus driver
Configuration changes:
- more imx platforms are now enabled in multi_v7_defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lVQn
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few patches have come up since the merge window. The largest one is
a rewrite of the PXA lubbock/mainstone IRQ handling. This was already
broken in 2011 by a change to the GPIO code and only noticed now.
The other changes contained here are:
MAINTAINERS file updates:
- Ray Jui and Scott Branden are now co-maintainers for some of the
mach-bcm chips, while Christian Daudt and Marc Carino have stepped
down.
- Andrew Victor is no longer maintaining at91. Instead, Alexandre
Belloni now becomes an official maintainer, after having done a
bulk of the work for a while.
- Baruch Siach, who added the mach-digicolor platform in 4.1 is now
listed as maintainer
- The git URL for mach-socfpga has changed
Bug fixes:
- Three bug fixes for new rockchip rk3288 code
- A regression fix to make SD card support work on certain ux500
boards
- multiple smaller dts fixes for imx, omap, mvebu, and shmobile
- a regression fiix for omap3 power consumption
- a fix for regression in the ARM CCI bus driver
Configuration changes:
- more imx platforms are now enabled in multi_v7_defconfig"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
MAINTAINERS: add Conexant Digicolor machines entry
MAINTAINERS: socfpga: update the git repo for SoCFPGA
ARM: multi_v7_defconfig: Select more FSL SoCs
MAINTAINERS: replace an AT91 maintainer
drivers: CCI: fix used_mask init in validate_group()
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
MAINTAINERS: Update brcmstb entry
MAINTAINERS: Remove Christian Daudt for mach-bcm
...
We cast away the volatile, but really, why make it volatile at all?
We already do a mb() inside the cpumask_empty() loop.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reset code functionality is mostly a copy paste between OMAP4+ and
AM33xx+. Re-use the omap4 code where possible, and just keep the special
implementation for de-asserting the hardreset lines for AM33xx, as
AM33xx+ devices have slightly different register layouts compared to
OMAP4+. This patch also fixes the hardreset issues faced on AM43xx.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM43xx has slightly different reset register layout compared to OMAP4+,
with varying status bit shifts and status register offsets. Current
code assumes static offsets and identical status / reset control bit
shifts, which is wrong. This patch adds PRM core support for passing
the actual implementations from hwmod code. AM43xx mappings will be fixed
in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds VPFE HWMOD data for AM43xx.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
[paul@pwsan.com: updated to apply on v4.1-rc1]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle are failing on Exynos5250 Snow.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Remove the extra zero in the "cpu-crit-0" trip point for exynos5420
and exynos5440.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos4412 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-X2/U2/U3 boards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Commit ea08de16eb ("ARM: dts: Add DISP1 power domain for exynos5420")
added a device node for the Exynos5420 DISP1 power domain but dit not
make the DP controller a consumer of that power domain.
This causes an "Unhandled fault: imprecise external abort" error if the
exynos-dp driver tries to access the DP controller registers and the PD
was turned off. This lead to a kernel panic and a complete system hang.
Make the DP controller device node a consumer of the DISP1 power domain
to ensure that the PD is turned on when the exynos-dp driver is probed.
Fixes: ea08de16eb ("ARM: dts: Add DISP1 power domain for exynos5420")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Consider "(u64)insn1.imm << 32 | imm" in the arm64 JIT. Since imm is
signed 32-bit, it is sign-extended to 64-bit, losing the high 32 bits.
The fix is to convert imm to u32 first, which will be zero-extended to
u64 implicitly.
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: 30d3d94cc3 ("arm64: bpf: add 'load 64-bit immediate' instruction")
Signed-off-by: Xi Wang <xi.wang@gmail.com>
[will: removed non-arm64 bits and redundant casting]
Signed-off-by: Will Deacon <will.deacon@arm.com>
drm-intel-next-2015-04-23:
- dither support for ns2501 dvo (Thomas Richter)
- some polish for the gtt code and fixes to finally enable the cmd parser on hsw
- first pile of bxt stage 1 enabling (too many different people to list ...)
- more psr fixes from Rodrigo
- skl rotation support from Chandra
- more atomic work from Ander and Matt
- pile of cleanups and micro-ops for execlist from Chris
drm-intel-next-2015-04-10:
- cdclk handling cleanup and fixes from Ville
- more prep patches for olr removal from John Harrison
- gmbus pin naming rework from Jani (prep for bxt)
- remove ->new_config from Ander (more atomic conversion work)
- rps (boost) tuning and unification with byt/bsw from Chris
- cmd parser batch bool tuning from Chris
- gen8 dynamic pte allocation (Michel Thierry, based on work from Ben Widawsky)
- execlist tuning (not yet all of it) from Chris
- add drm_plane_from_index (Chandra)
- various small things all over
* tag 'drm-intel-next-2015-04-23-fixed' of git://anongit.freedesktop.org/drm-intel: (204 commits)
drm/i915/gtt: Allocate va range only if vma is not bound
drm/i915: Enable cmd parser to do secure batch promotion for aliasing ppgtt
drm/i915: fix intel_prepare_ddi
drm/i915: factor out ddi_get_encoder_port
drm/i915/hdmi: check port in ibx_infoframe_enabled
drm/i915/hdmi: fix vlv infoframe port check
drm/i915: Silence compiler warning in dvo
drm/i915: Update DRIVER_DATE to 20150423
drm/i915: Enable dithering on NatSemi DVO2501 for Fujitsu S6010
rm/i915: Move i915_get_ggtt_vma_pages into ggtt_bind_vma
drm/i915: Don't try to outsmart gcc in i915_gem_gtt.c
drm/i915: Unduplicate i915_ggtt_unbind/bind_vma
drm/i915: Move ppgtt_bind/unbind around
drm/i915: move i915_gem_restore_gtt_mappings around
drm/i915: Fix up the vma aliasing ppgtt binding
drm/i915: Remove misleading comment around bind_to_vm
drm/i915: Don't use atomics for pg_dirty_rings
drm/i915: Don't look at pg_dirty_rings for aliasing ppgtt
drm/i915/skl: Support Y tiling in MMIO flips
drm/i915: Fixup kerneldoc for struct intel_context
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
iTLB-load-misses and LLC-load-misses count incorrectly on SLM.
There is no ITLB.MISSES support on SLM. Event PAGE_WALKS.I_SIDE_WALK
should be used to count iTLB-load-misses. This event counts when an
instruction (I) page walk is completed or started. Since a page walk
implies a TLB miss, the number of TLB misses can be counted by counting
the number of pagewalks.
DMND_DATA_RD counts both demand and DCU prefetch data reads. However,
LLC-load-misses should only count demand reads. There is no way to not
include prefetches with a single counter on SLM. So the LLC-load-misses
support should be removed on SLM.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1429608881-5055-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Fix for a PCI resources management regression introduced during
the 4.0 cycle and related to the handling of ACPI resources'
Producer/Consumer flags that turn out to be useless (Jiang Liu).
- Fix for a MacBook regression related to the Smart Battery Subsystem
(SBS) driver causing various problems (stalls on boot, failure to
detect or report battery) to happen and introduced during the 3.18
cycle (Chris Bainbridge).
- Fix for an ACPI/PNP device enumeration regression introduced during
the 3.16 cycle caused by failing to include two PNP device IDs into
the list of IDs that PNP device objects need to be created for
(Witold Szczeponik).
- Fixes for two minor mistakes in the ACPI GPIO properties
documentation (Antonio Ospite, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=JFUn
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These include three regression fixes (PCI resources management,
ACPI/PNP device enumeration, ACPI SBS on MacBook) and two ACPI
documentation fixes related to GPIO.
Specifics:
- Fix for a PCI resources management regression introduced during the
4.0 cycle and related to the handling of ACPI resources'
Producer/Consumer flags that turn out to be useless (Jiang Liu)
- Fix for a MacBook regression related to the Smart Battery Subsystem
(SBS) driver causing various problems (stalls on boot, failure to
detect or report battery) to happen and introduced during the 3.18
cycle (Chris Bainbridge)
- Fix for an ACPI/PNP device enumeration regression introduced during
the 3.16 cycle caused by failing to include two PNP device IDs into
the list of IDs that PNP device objects need to be created for
(Witold Szczeponik)
- Fixes for two minor mistakes in the ACPI GPIO properties
documentation (Antonio Ospite, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
* acpi-resources:
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
* acpi-battery:
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
* acpi-doc:
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
* acpi-pnp:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
in the Ux500 DT but triggered by proper error handling in v4.1-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2YtL
-----END PGP SIGNATURE-----
Merge tag 'stericsson-fixes-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
Merge "Ux500 fixes" from Linus Walleij:
This fixes an MMC/SD configuration issue present for some time
in the Ux500 DT but triggered by proper error handling in v4.1-rc1.
* tag 'stericsson-fixes-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable GPIO regulator for SD-card for snowball
ARM: ux500: Enable GPIO regulator for SD-card for HREF boards
ARM: ux500: Move GPIO regulator for SD-card into board DTSs
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tOGf
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.1-rc1" from Tony Lindgren:
Fixes for omaps, mostly a fix for power power consumption
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
* tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
Disable the unused internal RTC in the dts of the OpenBlock AX3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVDtLIACgkQCwYYjhRyO9WCiwCfTBYFFDMZxK/W9qLdhU8mj/iD
tDQAn3TDsfWEIHm+c6DeZqj35Q74yPGA
=Gggv
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.1' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fix for 4.1" from Gregory CLEMENT:
Disable the unused internal RTC in the dts of the OpenBlock AX3
* tag 'mvebu-fixes-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: armada-xp-openblocks-ax3-4: Disable internal RTC
These fixes reenable the lubbock(pxa25x) and mainstone(pxa27x)
platforms, which were broken since the gpio handling was
converted to a driver, and the interrupt ordering broke the
external interrupts of these systems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bvjh
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.1-rc2' of https://github.com/rjarzmik/linux into fixes
Merged "ARM: pxa: fixes for v4.1-rc2" from Robert Jarzmik:
These fixes reenable the lubbock(pxa25x) and mainstone(pxa27x)
platforms, which were broken since the gpio handling was
converted to a driver, and the interrupt ordering broke the
external interrupts of these systems.
* tag 'fixes-for-v4.1-rc2' of https://github.com/rjarzmik/linux:
ARM: pxa: lubbock: use new pxa_cplds driver
ARM: pxa: mainstone: use new pxa_cplds driver
ARM: pxa: pxa_cplds: add lubbock and mainstone IO
- A couple of imx23-olinuxino device tree fixes regarding to LED GPIO
polarity and USB dr_mode setting
- One i.MX28 device tree fix on AUART4 TX-DMA interrupt name
- Add missing pwm-cells to PWM4 for i.MX25 device tree
- Fix imx6q-phytec device tree to get correct USB VBUS control
- Drop invalid pinctrl-assert-gpios property from imx6qdl-sabreauto
device tree, which was sneaked in from vendor device tree
- One fix on Wolfram's broken email address
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVQO+yAAoJEFBXWFqHsHzOWkwH/RQGJQOAXT5QFwCxwjJ8rWbQ
QdB7SWUFufEoAUura83ZrER3FT1WmIRrtvLYypdopUUPhABT8cir5nwRjVd0iMc1
NaC31HohR27N3XZ0zt8yFlvpm03MSYirgpPyB8/tkvMhMv3ghlz5az2PzoAzc5vl
X9uOricn+gKWZsOYQ2X90VJtvNtipV64NKhwEWkg+t1lyxZmfcP30iY8LM3/B21D
qP4k08SIuPo3YoIPjITSmHqtzgp5X9Rf1FTfKmBvecBtt5W4GfrbtsylTvC1ISQC
p4FhDBOrN8hRl1ocbSQvFQybz2poOF/UTFwpWHtAPJxwY11j+IDs2SC33H7whXs=
=H+ZO
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.1" from Shawn Guo:
- A couple of imx23-olinuxino device tree fixes regarding to LED GPIO
polarity and USB dr_mode setting
- One i.MX28 device tree fix on AUART4 TX-DMA interrupt name
- Add missing pwm-cells to PWM4 for i.MX25 device tree
- Fix imx6q-phytec device tree to get correct USB VBUS control
- Drop invalid pinctrl-assert-gpios property from imx6qdl-sabreauto
device tree, which was sneaked in from vendor device tree
- One fix on Wolfram's broken email address
* tag 'imx-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-sabreauto: remove pinctrl-assert-gpios
ARM: dts: imx28: Fix AUART4 TX-DMA interrupt name
ARM: dts: imx25: Add #pwm-cells to pwm4
ARM: dts: imx6: phyFLEX: USB VBUS control is active-high
ARM: mach-imx: devices: platform-sdhci-esdhc-imx: fix broken email address
ARM: dts: imx23-olinuxino: Fix dr_mode of usb0
ARM: dts: imx23-olinuxino: Fix polarity of LED GPIO
And I've given up on the timer7 issue. While I initially thought
devices would either have both the grave mmu issue requiring a uboot
update and the timer7 issue or none, it looks like in all units in the
field the mmu issue got fixed while the timer7 issue stayed on.
So instead of making everybody wanting to use mainline jump through a
hoop just make sure timer7 is on on boot before we init the arch-timer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJVOsT2AAoJEPOmecmc0R2BQyQH/A94imdnOCWSoSw0xE7xBm04
QgTBaI4CHspFiSdE2Y0/2rCnaJ1xyWL/YOdcqAGRHDIRGQtBdILivoO1xRc875Sh
xI274cxNrKsI6v0PuX09uDXcv7jQOY1TAad8wkFq99+r1AguvR6Fcqh0thSwCm/o
Bt0SLmfQp9zzFwuOz4YYIfoCHXicfnxLZ79KsYqvHWuF/C4FMxQ2dabn/2bRMapH
ad8nQUwcUpgnLZF6rdEsebAzHplfItLq35ZxDWm5RGL9qSX44fVPbGeNGymqbmBn
8tX1eqVbDpe9WUVWxeeJEvi/MXWiJRP7FVvxn1+ORP/nWNJp0/1qOXYj9huTcys=
=zFY0
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rockchip-socfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: some soc-level fixes for 4.1" from Heiko Stübner:
Two fixes from Chris Zhong, fixing some suspend oddities.
And I've given up on the timer7 issue. While I initially thought
devices would either have both the grave mmu issue requiring a uboot
update and the timer7 issue or none, it looks like in all units in the
field the mmu issue got fixed while the timer7 issue stayed on.
So instead of making everybody wanting to use mainline jump through a
hoop just make sure timer7 is on on boot before we init the arch-timer.
* tag 'v4.1-rockchip-socfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
rockchip: make sure timer7 is enabled on rk3288 platforms
ARM: rockchip: fix undefined instruction of reset_ctrl_regs
ARM: rockchip: disable dapswjdp during suspend
Ensure that the asm code finalization path is not triggered when
invoked via final(), since it already takes care of that itself.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ensure that the asm code finalization path is not triggered when
invoked via final(), since it already takes care of that itself.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The arm64 CRC32 (not CRC32c) implementation was not quite doing
the same thing as the generic one. Fix that.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Fix blkback regression if using persistent grants.
- Fix various event channel related suspend/resume bugs.
- Fix AMD x86 regression with X86_BUG_SYSRET_SS_ATTRS.
- SWIOTLB on ARM now uses frames <4 GiB (if available) so device only
capable of 32-bit DMA work.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJVSiC1AAoJEFxbo/MsZsTRojgH/1zWPD0r5WMAEPb6DFdb7Ga1
SqBbyHFu43axNwZ7EvUzSqI8BKDPbTnScQ3+zC6Zy1SIEfS+40+vn7kY/uASmWtK
LYaYu8nd49OZP8ykH0HEvsJ2LXKnAwqAwvVbEigG7KJA7h8wXo7aDwdwxtZmHlFP
18xRTfHcrnINtAJpjVRmIGZsCMXhXQz4bm0HwsXTTX0qUcRWtxydKDlMPTVFyWR8
wQ2m5+76fQ8KlFsoJEB0M9ygFdheZBF4FxBGHRrWXBUOhHrQITnH+cf1aMVxTkvy
NDwiEebwXUDHacv21onszoOkNjReLsx+DWp9eHknlT/fgPo6tweMM2yazFGm+JQ=
=W683
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.1b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- fix blkback regression if using persistent grants
- fix various event channel related suspend/resume bugs
- fix AMD x86 regression with X86_BUG_SYSRET_SS_ATTRS
- SWIOTLB on ARM now uses frames <4 GiB (if available) so device only
capable of 32-bit DMA work.
* tag 'for-linus-4.1b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Add __GFP_DMA flag when xen_swiotlb_init gets free pages on ARM
hypervisor/x86/xen: Unset X86_BUG_SYSRET_SS_ATTRS on Xen PV guests
xen/events: Set irq_info->evtchn before binding the channel to CPU in __startup_pirq()
xen/console: Update console event channel on resume
xen/xenbus: Update xenbus event channel on resume
xen/events: Clear cpu_evtchn_mask before resuming
xen-pciback: Add name prefix to global 'permissive' variable
xen: Suspend ticks on all CPUs during suspend
xen/grant: introduce func gnttab_unmap_refs_sync()
xen/blkback: safely unmap purge persistent grants
Pull x86 fixes from Ingo Molnar:
"EFI fixes, and FPU fix, a ticket spinlock boundary condition fix and
two build fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Always restore_xinit_state() when use_eager_cpu()
x86: Make cpu_tss available to external modules
efi: Fix error handling in add_sysfs_runtime_map_entry()
x86/spinlocks: Fix regression in spinlock contention detection
x86/mm: Clean up types in xlate_dev_mem_ptr()
x86/efi: Store upper bits of command line buffer address in ext_cmd_line_ptr
efivarfs: Ensure VariableName is NUL-terminated
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also an uncore PMU driver fix and an uncore
PMU driver hardware-enablement addition"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Fix segfault if passed with ''.
perf report: Fix -T/--threads option to work again
perf bench numa: Fix immediate meeting of convergence condition
perf bench numa: Fixes of --quiet argument
perf bench futex: Fix hung wakeup tasks after requeueing
perf probe: Fix bug with global variables handling
perf top: Fix a segfault when kernel map is restricted.
tools lib traceevent: Fix build failure on 32-bit arch
perf kmem: Fix compiles on RHEL6/OL6
tools lib api: Undefine _FORTIFY_SOURCE before setting it
perf kmem: Consistently use PRIu64 for printing u64 values
perf trace: Disable events and drain events when forked workload ends
perf trace: Enable events when doing system wide tracing and starting a workload
perf/x86/intel/uncore: Move PCI IDs for IMC to uncore driver
perf/x86/intel/uncore: Add support for Intel Haswell ULT (lower power Mobile Processor) IMC uncore PMUs
perf/x86/intel: Add cpu_(prepare|starting|dying) for core_pmu
Make sure that xen_swiotlb_init allocates buffers that are DMA capable
when at least one memblock is available below 4G. Otherwise we assume
that all devices on the SoC can cope with >4G addresses. We do this on
ARM and ARM64, where dom0 is mapped 1:1, so pfn == mfn in this case.
No functional changes on x86.
From: Chen Baozi <baozich@gmail.com>
Signed-off-by: Chen Baozi <baozich@gmail.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Chen Baozi <baozich@gmail.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The following commit:
f893959b08 ("x86/fpu: Don't abuse drop_init_fpu() in flush_thread()")
removed drop_init_fpu() usage from flush_thread(). This seems to break
things for me - the Go 1.4 test suite fails all over the place with
floating point comparision errors (offending commit found through
bisection).
The functional change was that flush_thread() after this commit
only calls restore_init_xstate() when both use_eager_fpu() and
!used_math() are true. drop_init_fpu() (now fpu_reset_state()) calls
restore_init_xstate() regardless of whether current used_math() - apply
the same logic here.
Switch used_math() -> tsk_used_math(tsk) to consistently use the grabbed
tsk instead of current, like in the rest of flush_thread().
Tested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pekka Riikonen <priikone@iki.fi>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: f893959b ("x86/fpu: Don't abuse drop_init_fpu() in flush_thread()")
Link: http://lkml.kernel.org/r/1430147441-9820-1-git-send-email-bobbypowers@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
EFI variable name - Ross Lagerwall
* Stop erroneously dropping upper 32-bits of boot command line pointer
in EFI boot stub and stash them in ext_cmd_line_ptr - Roy Franz
* Fix double-free bug in error handling code path of EFI runtime map
code - Dan Carpenter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f7a2
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Avoid garbage names in efivarfs due to buggy firmware by zeroing
EFI variable name. (Ross Lagerwall)
* Stop erroneously dropping upper 32 bits of boot command line pointer
in EFI boot stub and stash them in ext_cmd_line_ptr. (Roy Franz)
* Fix double-free bug in error handling code path of EFI runtime map
code. (Dan Carpenter)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 75182b1632 ("x86/asm/entry: Switch all C consumers of
kernel_stack to this_cpu_sp0()") changed current_thread_info
to use this_cpu_sp0, and indirectly made it rely on init_tss
which was exported with EXPORT_PER_CPU_SYMBOL_GPL.
As a result some macros and inline functions such as set/get_fs,
test_thread_flag and variants have been made unusable for
external modules.
Make cpu_tss exported with EXPORT_PER_CPU_SYMBOL so that these
functions are accessible again, as they were previously.
Signed-off-by: Marc Dionne <marc.dionne@your-file-system.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/1430763404-21221-1-git-send-email-marc.dionne@your-file-system.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 61f01dd941 ("x86_64, asm: Work around AMD SYSRET SS descriptor
attribute issue") makes AMD processors set SS to __KERNEL_DS in
__switch_to() to deal with cases when SS is NULL.
This breaks Xen PV guests who do not want to load SS with__KERNEL_DS.
Since the problem that the commit is trying to address would have to be
fixed in the hypervisor (if it in fact exists under Xen) there is no
reason to set X86_BUG_SYSRET_SS_ATTRS flag for PV VPCUs here.
This can be easily achieved by adding x86_hyper_xen_hvm.set_cpu_features
op which will clear this flag. (And since this structure is no longer
HVM-specific we should do some renaming).
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
This fix the below build error:
arch/arm64/mm/dump.c: In function ‘ptdump_init’:
arch/arm64/mm/dump.c:331:18: error: ‘VMEMMAP_START_NR’ undeclared (first use in this function)
address_markers[VMEMMAP_START_NR].start_address =
^
arch/arm64/mm/dump.c:331:18: note: each undeclared identifier is reported only once for each
function it appears in
arch/arm64/mm/dump.c:333:18: error: ‘VMEMMAP_END_NR’ undeclared (first use in this function)
address_markers[VMEMMAP_END_NR].start_address =
^
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Jungseung Lee <js07.lee@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This reverts most of commit fef7f2b201.
It turns out that there are a couple of problems with the way we're
fixing up branch instructions used as part of alternative instruction
sequences:
(1) If the branch target is also in the alternative sequence, we'll
generate a branch into the .altinstructions section which actually
gets freed.
(2) The calls to aarch64_insn_{read,write} bring an awful lot more
code into the patching path (e.g. taking locks, poking the fixmap,
invalidating the TLB) which isn't actually needed for the early
patching run under stop_machine, but makes the use of alternative
sequences extremely fragile (as we can't patch code that could be
used by the patching code).
Given that no code actually requires alternative patching of immediate
branches, let's remove this support for now and revisit it when we've
got a user. We leave the updated size check, since we really do require
the sequences to be the same length.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A spinlock is regarded as contended when there is at least one waiter.
Currently, the code that checks whether there are any waiters rely on
tail value being greater than head. However, this is not true if tail
reaches the max value and wraps back to zero, so arch_spin_is_contended()
incorrectly returns 0 (not contended) when tail is smaller than head.
The original code (before regression) handled this case by casting the
(tail - head) to an unsigned value. This change simply restores that
behavior.
Fixes: d6abfdb202 ("x86/spinlocks/paravirt: Fix memory corruption on unlock")
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Cc: peterz@infradead.org
Cc: Waiman.Long@hp.com
Cc: borntraeger@de.ibm.com
Cc: oleg@redhat.com
Cc: raghavendra.kt@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1430799331-20445-1-git-send-email-tahsin@google.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:
1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
11 bits on OMAP5 as against 8 bits on OMAP4, with the master
NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
field.
2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
input sources on OMAP5. The common DEBUGSS source is at a
different input on each SoC.
Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a typo in DRA7 dtsi where 12 bytes are needed for register
description of ABB efuse registers, however only 8 bytes are provided
to map. For some weird reason, this does not generate abort at offset
0x8, probably due to default maps already provided in io.c for the bus
register ranges.
Reported-by: Matt Gessner <Matt.Gessner@windriver.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching the GPIO fan
gpio over from 1 to 2 to allow for a potential fix at a later point in
time for USB client VBUS detection using PMIC VBUS detect capability.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching over to UART
pins that now allow for UART download capability. All original boards
should either have been returned for modifications or already modified
for the required change and maintaining compatibility for older boards
are no longer needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new AM437x SK Beta boards have removed the
large capacitors on the gpio-matrix column lines
which means we can reduce col-scan-delay-us to 5us
without loosing functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit uses a NewHaven Display module with
a 4.3" display and EDT FT5306 touchscreen
On that module's new revision, NewHave decided to change
the pinout on the 6 pin flat-pcb touchscreen connector so
that instead of having WAKE pin, we now have RESETn.
The new display module is available on AM437x SK Beta and
all new revisions while the older revision is only available
on AM437x SK Alpha which, unfortunately, can't be supported
anymore in mainline without a revert of this patch.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With commit bc078316d8 ("ARM: dts: DRA7: Add node for RTC"), we now
have AM57xx RTC register itself as alias 0 even before DS1307 or TPS
rtc drivers are loaded up. However, since neither TPS, nor AM57xx RTC
are capable of being backedup by battery, we would like to maintain
the "primary" rtc as mcp79410 rtc device.
This also generates the following warnings in the bootlog highlighting
the issue:
[ 5.895445] rtc-ds1307 2-006f: /aliases ID 0 not available
...
[ 6.476285] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: /aliases ID 1 not available
So, add proper aliases to ensure that RTC order is always consistent
to userspace immaterial of probe order.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt polarity provided in devicetree is used to configure
the interrupt controller(ARM GIC), however, it seems that we have an
inverter at the GIC boundary inside AM57xx which inverts the signal
input from sys_irq external interrupt source.
Further, as per GIC distributor TRM,
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438d/BGBHIACJ.html#BABJFCFB
ARM GIC distributor does not support IRQ trigger type
IRQ_TYPE_LEVEL_LOW, and only rising or level high signals.
However, for some reason, the current configuration(which gets ignored
by GIC driver) functions on some platforms, however, on few platforms
results in infinite interrupts hogging the system down.
Switch over to rising edge for GIC configuration which is also aligned
with trigger point from the RTC chip and the internal inversion.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing #iommu-cells property to the isp and iva iommu nodes. This
fixes the binding (property is required according to the generic iommu
binding) and removes the following kernel warning triggered once the
iommu nodes are referenced:
[ 0.647521] /ocp/isp@480bc000: could not get #iommu-cells for /ocp/mmu@480bd400
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to enable EXTCON_USB_GPIO_USB and not
EXTCON_GPIO_USB.
Fixes: c08a54c0eb ("ARM: omap2plus_defconfig: Enable EXTCON_GPIO_USB")
Reported-by: Nishant Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by-by: Nishanth Menon <nm@ti.com
Tested-by: Nishanth Menon <nm@ti.com
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
N900 audio recording needs that codec provides bias voltage for integrated
digital microphone and headset microphone depending which one is used.
Digital microphone uses 2 V bias and it comes from the codec A part. Codec
B part drives the headset microphone bias and that is set to 2.5 V.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[Jarkko: Headset mic bias changed to 2 (2.5 V) as it was before commit
e2e8bfdf61 ("ASoC: tlv320aic3x: Convert mic bias to a supply widget")]
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we use a combination of VMODE and I2C4 for retention modes,
eventually the off idle power consumption will creep up by about
23mW, even during off mode with I2C4 always staying enabled.
Turns out this is because of erratum i531 "Extra Power Consumed
When Repeated Start Operation Mode Is Enabled on I2C Interface
Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth
Menon <nm@ti.com>.
Let's fix the issue by adding i2c_cfg_clear_mask for the bits
to clear when initializing the I2C4 adapter so we can clear
SREN bit that drives the I2C4 lines low otherwise when there
is no traffic.
Fixes: 3b8c4ebb76 ("ARM: OMAP3: Fix idle mode signaling for
Cc: stable@vger.kernel.org # v3.16+
sys_clkreq and sys_off_mode")
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With commit 9fd85eb502 ("ARM: pmu: add support for interrupt-affinity
property"), we print a warning when we find a PMU SPI with a missing
missing interrupt-affinity property in a pmu node. Unfortunately, we
pass the wrong (NULL) device node to of_node_full_name, resulting in
unhelpful messages such as:
hw perfevents: Failed to parse <no-node>/interrupt-affinity[0]
This patch fixes the name to that of the pmu node.
Fixes: 9fd85eb502 (ARM: pmu: add support for interrupt-affinity property)
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PPIs are affine by nature, so the interrupt-affinity property is not
used and therefore we shouldn't print a warning in its absence.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The block could never be compiled; CPU_ICACHE_STREAMING_DISABLE has not
been defined in Kconfig since the very first Git commit. Hence, we can
safely remove the entire block.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPU_ARM1020_CPU_IDLE is not defined in Kconfig. The last reference on
LKML dates back to 2001, so we can safely remove the comments to make
static analysis tools happy.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch 22b3c181c6 ("arm: dma-mapping: limit
IOMMU mapping size") added a check for IO address space size. However
this patch broke IOMMU initialization for typical platforms initialized
from device tree, which get the default IO address space size of 4GiB.
This value doesn't fit into size_t and fails a check introduced by that
commit resulting in failed dma-mapping/iommu initialization. This patch
fixes this issue by adding proper support for full 4GiB address space
size.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Build fix for SMP=n in book3s_xics.c
- Fix for Daniel's pci_controller_ops on powernv.
- Revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- Two EEH fixes from Gavin.
- Fix for CR corruption from Sam.
- Selftest build fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=S0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- build fix for SMP=n in book3s_xics.c
- fix for Daniel's pci_controller_ops on powernv.
- revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- two EEH fixes from Gavin.
- fix for CR corruption from Sam.
- selftest build fix.
* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Restore non-volatile CRs after nap
powerpc/eeh: Delay probing EEH device during hotplug
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
powerpc/pseries: Correct cpu affinity for dlpar added cpus
selftests/powerpc: Fix the pmu install rule
Revert "powerpc/tm: Abort syscalls in active transactions"
powerpc/powernv: Fix early pci_controller_ops loading.
powerpc/kvm: Fix SMP=n build error in book3s_xics.c
Whereas for Armada 370 and XP the main PLL frequency was 2GHz for the
Armada 375, 38x and 39x, the frequency is 1GHz. When writing support
for these last SoCs, there was no official value for the PLL. Now that
we have it, this patch fixes it in the device tree.
This value is currently only used by the NAND driver for the setting
the NAND timing. Fortunately it is not actually used: all the mainline
board with a NAND flash comes with a NAND device tree node using the
"marvell,nand-keep-config" property. With this property the timings
are not modified in the kernel driver and are kept from the
bootloader.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marcin Wojtas <mw@semihalf.com>
- Fix perf devicetree warnings at probe time
- Fix memory leak in __dma_free()
- Ensure DMA buffers are always zeroed
- Show IRQ trigger in /proc/interrupts (for parity with ARM)
- Implement byte and halfword access for smp_{load_acquire,store_release}
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVQlyfAAoJELescNyEwWM0ZTIIAKnK5bIr1jS9wP9wLJ8eZ++y
8p5RYluqtMBkYzbOpKr8HiJdg6GupNiSq6as+cf5T+Gc2D01HhFocqJbLrOCqJRA
RG5gFqkx/7FKTCwIt/DSygiwA+szPKTArf3YOi+EuDmCkcgRv38vac8yqlM1rI+M
UL2vdAEqvjPxPquzeAqrSIcwQ9jAYzEouh8VrMWigLFN5BvCUrO64r1y4zN7hbO1
RWEKPkIFMLDGCFwCn17mzLafVF2f0JH514sMZEQi2AQA/MlaIS3hM+SFJgxbRzib
ZRqXujX1Osi9W20VPwMtuUgQymEBQDAbXT35BxehL7MVMZhv66q+LBEabIpDMqM=
=4S7b
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Not too much here, but we've addressed a couple of nasty issues in the
dma-mapping code as well as adding the halfword and byte variants of
load_acquire/store_release following on from the CSD locking bug that
you fixed in the core.
- fix perf devicetree warnings at probe time
- fix memory leak in __dma_free()
- ensure DMA buffers are always zeroed
- show IRQ trigger in /proc/interrupts (for parity with ARM)
- implement byte and halfword access for smp_{load_acquire,store_release}"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: perf: Fix the pmu node name in warning message
arm64: perf: don't warn about missing interrupt-affinity property for PPIs
arm64: add missing PAGE_ALIGN() to __dma_free()
arm64: dma-mapping: always clear allocated buffers
ARM64: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
arm64: add missing data types in smp_load_acquire/smp_store_release
Patches 7cba160ad "powernv/cpuidle: Redesign idle states management"
and 77b54e9f2 "powernv/powerpc: Add winkle support for offline cpus"
use non-volatile condition registers (cr2, cr3 and cr4) early in the system
reset interrupt handler (system_reset_pSeries()) before it has been determined
if state loss has occurred. If state loss has not occurred, control returns via
the power7_wakeup_noloss() path which does not restore those condition
registers, leaving them corrupted.
Fix this by restoring the condition registers in the power7_wakeup_noloss()
case.
This is apparent when running a KVM guest on hardware that does not
support winkle or sleep and the guest makes use of secondary threads. In
practice this means Power7 machines, though some early unreleased Power8
machines may also be susceptible.
The secondary CPUs are taken off line before the guest is started and
they call pnv_smp_cpu_kill_self(). This checks support for sleep
states (in this case there is no support) and power7_nap() is called.
When the CPU is woken, power7_nap() returns and because the CPU is
still off line, the main while loop executes again. The sleep states
support test is executed again, but because the tested values cannot
have changed, the compiler has optimized the test away and instead we
rely on the result of the first test, which has been left in cr3
and/or cr4. With the result overwritten, the wrong branch is taken and
power7_winkle() is called on a CPU that does not support it, leading
to it stalling.
Fixes: 7cba160ad7 ("powernv/cpuidle: Redesign idle states management")
Fixes: 77b54e9f21 ("powernv/powerpc: Add winkle support for offline cpus")
[mpe: Massage change log a bit more]
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 1c509148b ("powerpc/eeh: Do probe on pci_dn") probes EEH
devices in early stage, which is reasonable to pSeries platform.
However, it's wrong for PowerNV platform because the PE# isn't
determined until the resources (IO and MMIO) are assigned to
PE in hotplug case. So we have to delay probing EEH devices
for PowerNV platform until the PE# is assigned.
Fixes: ff57b454dd ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When asserting reset in pcibios_set_pcie_reset_state(), the PE
is enforced to (hardware) frozen state in order to drop unexpected
PCI transactions (except PCI config read/write) automatically by
hardware during reset, which would cause recursive EEH error.
However, the (software) frozen state EEH_PE_ISOLATED is missed.
When users get 0xFF from PCI config or MMIO read, EEH_PE_ISOLATED
is set in PE state retrival backend. Unfortunately, nobody (the
reset handler or the EEH recovery functinality in host) will clear
EEH_PE_ISOLATED when the PE has been passed through to guest.
The patch sets and clears EEH_PE_ISOLATED properly during reset
in function pcibios_set_pcie_reset_state() to fix the issue.
Fixes: 28158cd ("Enhance pcibios_set_pcie_reset_state()")
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The incorrect ordering of operations during cpu dlpar add results in invalid
affinity for the cpu being added. The ibm,associativity property in the
device tree is populated with all zeroes for the added cpu which results in
invalid affinity mappings and all cpus appear to belong to node 0.
This occurs because rtas configure-connector is called prior to making the
rtas set-indicator calls. Phyp does not assign affinity information
for a cpu until the rtas set-indicator calls are made to set the isolation
and allocation state.
Correct the order of operations to make the rtas set-indicator
calls (done in dlpar_acquire_drc) before calling rtas configure-connector.
Fixes: 1a8061c46c ("powerpc/pseries: Add kernel based CPU DLPAR handling")
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The adv7511 IRQ is low level triggered, not falling edge triggered. The
wrong sense configuration results in no interrupt being triggered at
all, breaking hotplug detection. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Fixes: 83a0731b39 ("ARM: shmobile: koelsch: Add DU HDMI output support")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the interrupt handling was transferred to the pxa_cplds driver,
make the switch in lubbock platform code.
Fixes: 157d2644cb ("ARM: pxa: change gpio to platform device")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
As the interrupt handling was transferred to the pxa_cplds driver,
make the switch in mainstone platform code.
Fixes: 157d2644cb ("ARM: pxa: change gpio to platform device")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Historically, this support was in arch/arm/mach-pxa/lubbock.c and
arch/arm/mach-pxa/mainstone.c. When gpio-pxa was moved to drivers/pxa,
it became a driver, and its initialization and probing happened at
postcore initcall. The lubbock code used to install the chained lubbock
interrupt handler at init_irq() time.
The consequence of the gpio-pxa change is that the installed chained irq
handler lubbock_irq_handler() was overwritten in pxa_gpio_probe(_dt)(),
removing :
- the handler
- the falling edge detection setting of GPIO0, which revealed the
interrupt request from the lubbock IO board.
As a fix, move the gpio0 chained handler setup to a place where we have
the guarantee that pxa_gpio_probe() was called before, so that lubbock
handler becomes the true IRQ chained handler of GPIO0, demuxing the
lubbock IO board interrupts.
This patch moves all that handling to a mfd driver. It's only purpose
for the time being is the interrupt handling, but in the future it
should encompass all the motherboard CPLDs handling :
- leds
- switches
- hexleds
The same logic applies to mainstone board.
Fixes: 157d2644cb ("ARM: pxa: change gpio to platform device")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
An IO port or MMIO resource assigned to a PCI host bridge may be
consumed by the host bridge itself or available to its child
bus/devices. The ACPI specification defines a bit (Producer/Consumer)
to tell whether the resource is consumed by the host bridge itself,
but firmware hasn't used that bit consistently, so we can't rely on it.
Before commit 593669c2ac ("x86/PCI/ACPI: Use common ACPI resource
interfaces to simplify implementation"), arch/x86/pci/acpi.c ignored
all IO port resources defined by acpi_resource_io and
acpi_resource_fixed_io to filter out IO ports consumed by the host
bridge itself.
Commit 593669c2ac ("x86/PCI/ACPI: Use common ACPI resource interfaces
to simplify implementation") started accepting all IO port and MMIO
resources, which caused a regression that IO port resources consumed
by the host bridge itself became available to its child devices.
Then commit 63f1789ec7 ("x86/PCI/ACPI: Ignore resources consumed by
host bridge itself") ignored resources consumed by the host bridge
itself by checking the IORESOURCE_WINDOW flag, which accidently removed
MMIO resources defined by acpi_resource_memory24, acpi_resource_memory32
and acpi_resource_fixed_memory32.
On x86 and IA64 platforms, all IO port and MMIO resources are assumed
to be available to child bus/devices except one special case:
IO port [0xCF8-0xCFF] is consumed by the host bridge itself
to access PCI configuration space.
So explicitly filter out PCI CFG IO ports[0xCF8-0xCFF]. This solution
will also ease the way to consolidate ACPI PCI host bridge common code
from x86, ia64 and ARM64.
Related ACPI table are archived at:
https://bugzilla.kernel.org/show_bug.cgi?id=94221
Related discussions at:
http://patchwork.ozlabs.org/patch/461633/https://lkml.org/lkml/2015/3/29/304
Fixes: 63f1789ec7 (Ignore resources consumed by host bridge itself)
Reported-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pvclock read; instead use the correct protocol in KVM.
This removes the need for task migration notifiers in core
scheduler code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVQkUWAAoJEL/70l94x66DhfcH/A8RTHUOELtoy+v2weahn21m
FFWEnEUlCWzYgmiddgFdlr6+ub386W3ryFsXKPqjrn/8LVv3yS7tK1NJF8d03LQw
n7HtIsrF01E9UI8CIWO4S/mUxWQev6vEJ9NXtNrsJcRmhSeLaIZkPjTH8Zqyx4i9
ZvG4731WHXmxvbJ03bfJU9Y8OwHXe55GMi614aTxPndVBGdvIRu2Oj6aTfQTeab/
7tEujub0MKWp74a7eyNU4GItcvIAXZCQt2wMc5dN1VK3ma5FTOnHIOuhAb8mACFF
qEeGhtxAnOf7W+s9J8i7zVBdA5MOS0vUKng361ZOVGDb0OLqcVADW7GpuTZfRAM=
=2A7v
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm changes from Paolo Bonzini:
"Remove from guest code the handling of task migration during a pvclock
read; instead use the correct protocol in KVM.
This removes the need for task migration notifiers in core scheduler
code"
[ The scheduler people really hated the migration notifiers, so this was
kind of required - Linus ]
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86: pvclock: Really remove the sched notifier for cross-cpu migrations
kvm: x86: fix kvmclock update protocol
When compiling the kernel for GCOV (CONFIG_GCOV_KERNEL,-fprofile-arcs),
gcc allocates a lot of stack space because of the large switch statement
in bpf_jit_insn().
This leads to the following compile warning:
arch/s390/net/bpf_jit_comp.c: In function 'bpf_jit_prog':
arch/s390/net/bpf_jit_comp.c:1144:1: warning: frame size of
function 'bpf_jit_prog' is 12592 bytes which is more than
half the stack size. The dynamic check would not be reliable.
No check emitted for this function.
arch/s390/net/bpf_jit_comp.c:1144:1: warning: the frame size of 12504
bytes is larger than 1024 bytes [-Wframe-larger-than=]
And indead gcc allocates 12592 bytes of stack space:
# objdump -d arch/s390/net/bpf_jit_comp.o
...
0000000000000c60 <bpf_jit_prog>:
c60: eb 6f f0 48 00 24 stmg %r6,%r15,72(%r15)
c66: b9 04 00 ef lgr %r14,%r15
c6a: e3 f0 fe d0 fc 71 lay %r15,-12592(%r15)
As a workaround of that problem we now define bpf_jit_insn() as
noinline which then reduces the stack space.
# objdump -d arch/s390/net/bpf_jit_comp.o
...
0000000000000070 <bpf_jit_insn>:
70: eb 6f f0 48 00 24 stmg %r6,%r15,72(%r15)
76: c0 d0 00 00 00 00 larl %r13,76 <bpf_jit_insn+0x6>
7c: a7 f1 3f 80 tmll %r15,16256
80: b9 04 00 ef lgr %r14,%r15
84: e3 f0 ff a0 ff 71 lay %r15,-96(%r15)
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390x ALU64_DIV/MOD has been implemented according to the eBPF
interpreter specification that used do_div(). This function does a 64-bit
by 32-bit divide. It turned out that this was wrong and now the interpreter
uses div64_u64_rem() for full 64-bit division.
So fix this and use full 64-bit division in the s390x eBPF backend code.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With commit d5efd9cc9c ("arm64: pmu: add support for interrupt-affinity
property"), we print a warning when we find a PMU SPI with a missing
missing interrupt-affinity property in a pmu node. Unfortunately, we
pass the wrong (NULL) device node to of_node_full_name, resulting in
unhelpful messages such as:
hw perfevents: Failed to parse <no-node>/interrupt-affinity[0]
This patch fixes the name to that of the pmu node.
Fixes: d5efd9cc9c (arm64: pmu: add support for interrupt-affinity property)
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
PPIs are affine by nature, so the interrupt-affinity property is not
used and therefore we shouldn't print a warning in its absence.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This reverts commit feba40362b.
Although the principle of this change is good, the implementation has a
few issues.
Firstly we can sometimes fail to abort a syscall because r12 may have
been clobbered by C code if we went down the virtual CPU accounting
path, or if syscall tracing was enabled.
Secondly we have decided that it is safer to abort the syscall even
earlier in the syscall entry path, so that we avoid the syscall tracing
path when we are transactional.
So that we have time to thoroughly test those changes we have decided to
revert this for this merge window and will merge the fixed version in
the next window.
NB. Rather than reverting the selftest we just drop tm-syscall from
TEST_PROGS so that it's not run by default.
Fixes: feba40362b ("powerpc/tm: Abort syscalls in active transactions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__dma_alloc() does a PAGE_ALIGN() on the passed in size argument before
doing anything else. __dma_free() does not. And because it doesn't, it is
possible to leak memory should size not be an integer multiple of PAGE_SIZE.
The solution is to add a PAGE_ALIGN() to __dma_free() like is done in
__dma_alloc().
Additionally, this patch removes a redundant PAGE_ALIGN() from
__dma_alloc_coherent(), since __dma_alloc_coherent() can only be called
from __dma_alloc(), which already does a PAGE_ALIGN() before the call.
Cc: stable@vger.kernel.org
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 77e32c89a7 ("clockevents: Manage device's state separately for
the core") decouples clockevent device's modes from states. With this
change when a Xen guest tries to resume, it won't be calling its
set_mode op which needs to be done on each VCPU in order to make the
hypervisor aware that we are in oneshot mode.
This happens because clockevents_tick_resume() (which is an intermediate
step of resuming ticks on a processor) doesn't call clockevents_set_state()
anymore and because during suspend clockevent devices on all VCPUs (except
for the one doing the suspend) are left in ONESHOT state. As result, during
resume the clockevents state machine will assume that device is already
where it should be and doesn't need to be updated.
To avoid this problem we should suspend ticks on all VCPUs during
suspend.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Load the PowerNV platform pci controller ops into pci controllers
after all the operations are loaded into the platform ops struct, not
before.
Otherwise we aren't actually setting the ops properly which can break
IO for some devices.
Fixes: 65ebf4b63 ("powerpc/powernv: Move controller ops from ppc_md to controller_ops")
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 34cb7954c0 "Convert ICS mutex lock to spin lock" added an
include of asm/spinlock.h, which does not work in the SMP=n case.
It should instead include linux/spinlock.h
Fixes: 34cb7954c0 ("KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock")
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull arch/tile bugfix from Chris Metcalf:
"This just fixes a compiler warning from an old bug that only recently
started generating a warning"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: properly use node_isset() on a nodemask_t
Pull s390 updates from Martin Schwidefsky:
"One additional new feature for 4.1, a new PRNG based on SHA-512 for
the zcrypt driver.
Two memory management related changes, the page table reallocation for
KVM is removed, and with file ptes gone the encoding of page table
entries is improved.
And three bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/zcrypt: Introduce new SHA-512 based Pseudo Random Generator.
s390/mm: change swap pte encoding and pgtable cleanup
s390/mm: correct transfer of dirty & young bits in __pmd_to_pte
s390/bpf: add dependency to z196 features
s390/3215: free memory in error path
s390/kvm: remove delayed reallocation of page tables for KVM
kexec: allocate the kexec control page with KEXEC_CONTROL_MEMORY_GFP
It should be the first controller, not the second. The indexes of the
usb resets were also wrong and have been fixed.
The issue was caused by the changes in 308efde ("ARM: tegra: Add resets
& has-utmi-pad-registers flag to all USB PHYs") being misapplied by git
due to the patch context being insufficient.
This broke USB after 6261b06 ("regulator: Defer lookup of supply to
regulator_get"), because it changed the order in which the controllers
were probed.
The fix for this issue was suggested by Mikko Perttunen and Tuomas
Tynkkynen.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Cc: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The code accidentally used cpu_isset() previously in one place
(though properly node_isset() elsewhere).
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
The pinctrl-assert-gpios is an invalid pinctrl property. It was
probably sneaked from vendor tree. Remove it.
Fixes: 4e18a2243a ("ARM: imx6qdl-sabreauto.dtsi: add max7310 support")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix a typo in the TX DMA interrupt name for AUART4.
This patch makes AUART4 operational again.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: f30fb03d4d ("ARM: dts: add generic DMA device tree binding for mxs-dma")
Cc: stable@vger.kernel.org
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The property '#pwm-cells' is currently missing. It is not possible to
use pwm4 without this property.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Fixes: 5658a68fb5 ("ARM i.MX25: Add devicetree")
Cc: <stable@vger.kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The fixed-regulator bindings require a separate property enable-active-high,
the standard gpio phandle property polarity setting is ignored.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: 4fe69a934b ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This reverts commits 0a4e6be9ca
and 80f7fdb1c7.
The task migration notifier was originally introduced in order to support
the pvclock vsyscall with non-synchronized TSC, but KVM only supports it
with synchronized TSC. Hence, on KVM the race condition is only needed
due to a bad implementation on the host side, and even then it's so rare
that it's mostly theoretical.
As far as KVM is concerned it's possible to fix the host, avoiding the
additional complexity in the vDSO and the (re)introduction of the task
migration notifier.
Xen, on the other hand, hasn't yet implemented vsyscall support at
all, so we do not care about its plans for non-synchronized TSC.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Suggested-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The kvmclock spec says that the host will increment a version field to
an odd number, then update stuff, then increment it to an even number.
The host is buggy and doesn't do this, and the result is observable
when one vcpu reads another vcpu's kvmclock data.
There's no good way for a guest kernel to keep its vdso from reading
a different vcpu's kvmclock data, but we don't need to care about
changing VCPUs as long as we read a consistent data from kvmclock.
(VCPU can change outside of this loop too, so it doesn't matter if we
return a value not fit for this VCPU.)
Based on a patch by Radim Krčmář.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
My Pengutronix address is not valid anymore, redirect people to the Pengutronix
kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The dr_mode of usb0 on imx233-olinuxino is left to default "otg".
Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the
same pin as USB_OTG_ID it's possible to disable USB host by LED toggling:
echo 0 > /sys/class/leds/green/brightness
[ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1
[ 1068.890000] usb usb1: USB disconnect, device number 1
[ 1068.920000] usb 1-1: USB disconnect, device number 2
[ 1068.920000] usb 1-1.1: USB disconnect, device number 3
[ 1069.070000] usb 1-1.2: USB disconnect, device number 4
[ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered
[ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11
This patch fixes the issue by setting dr_mode to "host" in the dts file.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Fixes: b493129482 ("ARM: dts: imx23-olinuxino: Add USB host support")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On imx23-olinuxino the LED turns on when level logic high is aplied to
GPIO2_1.
Fix the gpios property accordingly.
Fixes: b34aa18502 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Buffers allocated by dma_alloc_coherent() are always zeroed on Alpha,
ARM (32bit), MIPS, PowerPC, x86/x86_64 and probably other architectures.
It turned out that some drivers rely on this 'feature'. Allocated buffer
might be also exposed to userspace with dma_mmap() call, so clearing it
is desired from security point of view to avoid exposing random memory
to userspace. This patch unifies dma_alloc_coherent() behavior on ARM64
architecture with other implementations by unconditionally zeroing
allocated buffer.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since several interrupt controllers including GIC support both edge and
level triggered interrupts, it's useful to provide that information in
/proc/interrupts even on ARM64 similar to ARM and PPC.
This is based on Geert Uytterhoeven's commit 7c07005eea ("ARM: 8339/1:
Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 8053871d0f ("smp: Fix smp_call_function_single_async()
locking") introduced a call to smp_load_acquire() with a u16 argument,
but we only cared about u32 and u64 types in that function so far.
This resulted in a compiler warning fortunately, pointing at an
uninitialized use. Due to the implementation structure the compiler
misses that bug in the smp_store_release(), though.
Add the u16 and u8 variants using ldarh/stlrh and ldarb/stlrb,
respectively. Together with the compiletime_assert_atomic_type() check
this should cover all cases now.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There is no crystal connected to the internal RTC on the Open Block
AX3. So let's disable it in order to prevent the kernel probing the
driver uselessly. Eventually this patches removes the following
warning message from the boot log:
"rtc-mv d0010300.rtc: internal RTC not ticking"
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8 +
The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but
instead it's specific to the board. Move the definition of it, into the
board DTSs.
Fixes: c94a4ab7af ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.
Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.
This was exposed by a recent vDSO cleanup.
Fixes: e7d6eefaaa x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
Pull crypto fixes from Herbert Xu:
"This push fixes a build problem with img-hash under non-standard
configurations and a serious regression with sha512_ssse3 which can
lead to boot failures"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: img-hash - CRYPTO_DEV_IMGTEC_HASH should depend on HAS_DMA
crypto: x86/sha512_ssse3 - fixup for asm function prototype change
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlU70nMACgkQ31LbvUHyf1cYgwCfSmPhyLFmr0pGM/BxsVY7K1v6
PaEAn2+7xfZV38E6hwrGMrT42ZvKyL6r
=LHQU
-----END PGP SIGNATURE-----
Merge tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/cris updates from Jesper Nilsson:
"Some much needed love for the CRIS-port.
There's a bunch of changes this time, giving the CRISv32 port a bit of
modern makeover with device-tree, irq domain and gpiolib support, and
more switchover to generic frameworks.
Some small fixes and removal of the theoretical SMP support brings up
the rear"
* tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: fix integer overflow in ELF_ET_DYN_BASE
CRISv32: use GENERIC_SCHED_CLOCK
CRISv32: use MMIO clocksource
CRISv32: use generic clockevents
CRIS: use generic headers via Kbuild
CRIS: use generic cmpxchg.h
CRIS: use generic atomic.h
CRIS: use generic atomic bitops
CRISv10: remove redundant macros from system.h
CRIS: remove SMP code
CRISv32: don't enable irqs in INIT_THREAD
CRISv32: handle multiple signals
CRISv32: prevent bogus restarts on sigreturn
CRISv32: don't attempt syscall restart on irq exit
Add binding documentation for CRIS
CRIS: add Axis 88 board device tree
CRISv32: add device tree support
CRISv32: add irq domains support
CRIS: enable GPIOLIB
- Fix for mm_dec_nr_pmds() from Scott.
- Fixes for oopses seen with KVM + THP from Aneesh.
- Build fixes from Aneesh & Shreyas.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6yQx
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- fix for mm_dec_nr_pmds() from Scott.
- fixes for oopses seen with KVM + THP from Aneesh.
- build fixes from Aneesh & Shreyas.
* tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/mm: Fix build error with CONFIG_PPC_TRANSACTIONAL_MEM disabled
powerpc/kvm: Fix ppc64_defconfig + PPC_POWERNV=n build error
powerpc/mm/thp: Return pte address if we find trans_splitting.
powerpc/mm/thp: Make page table walk safe against thp split/collapse
KVM: PPC: Remove page table walk helpers
KVM: PPC: Use READ_ONCE when dereferencing pte_t pointer
powerpc/hugetlb: Call mm_dec_nr_pmds() in hugetlb_free_pmd_range()
Book3S HV only (debugging aids, minor performance improvements and some
cleanups). But there are also bug fixes and small cleanups for ARM,
x86 and s390.
The task_migration_notifier revert and real fix is still pending review,
but I'll send it as soon as possible after -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVOONLAAoJEL/70l94x66DbsMIAIpZPsaqgXOC1sDEiZuYay+6
rD4n4id7j8hIAzcf3AlZdyf5XgLlr6I1Zyt62s1WcoRq/CCnL7k9EljzSmw31WFX
P2y7/J0iBdkn0et+PpoNThfL2GsgTqNRCLOOQlKgEQwMP9Dlw5fnUbtC1UchOzTg
eAMeBIpYwufkWkXhdMw4PAD4lJ9WxUZ1eXHEBRzJb0o0ZxAATJ1tPZGrFJzoUOSM
WsVNTuBsNd7upT02kQdvA1TUo/OPjseTOEoksHHwfcORt6bc5qvpctL3jYfcr7sk
/L6sIhYGVNkjkuredjlKGLfT2DDJjSEdJb1k2pWrDRsY76dmottQubAE9J9cDTk=
=OAi2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second batch of KVM changes from Paolo Bonzini:
"This mostly includes the PPC changes for 4.1, which this time cover
Book3S HV only (debugging aids, minor performance improvements and
some cleanups). But there are also bug fixes and small cleanups for
ARM, x86 and s390.
The task_migration_notifier revert and real fix is still pending
review, but I'll send it as soon as possible after -rc1"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (29 commits)
KVM: arm/arm64: check IRQ number on userland injection
KVM: arm: irqfd: fix value returned by kvm_irq_map_gsi
KVM: VMX: Preserve host CR4.MCE value while in guest mode.
KVM: PPC: Book3S HV: Use msgsnd for signalling threads on POWER8
KVM: PPC: Book3S HV: Translate kvmhv_commence_exit to C
KVM: PPC: Book3S HV: Streamline guest entry and exit
KVM: PPC: Book3S HV: Use bitmap of active threads rather than count
KVM: PPC: Book3S HV: Use decrementer to wake napping threads
KVM: PPC: Book3S HV: Don't wake thread with no vcpu on guest IPI
KVM: PPC: Book3S HV: Get rid of vcore nap_count and n_woken
KVM: PPC: Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu
KVM: PPC: Book3S HV: Minor cleanups
KVM: PPC: Book3S HV: Simplify handling of VCPUs that need a VPA update
KVM: PPC: Book3S HV: Accumulate timing information for real-mode code
KVM: PPC: Book3S HV: Create debugfs file for each guest's HPT
KVM: PPC: Book3S HV: Add ICP real mode counters
KVM: PPC: Book3S HV: Move virtual mode ICP functions to real-mode
KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock
KVM: PPC: Book3S HV: Add guest->host real mode completion counters
KVM: PPC: Book3S HV: Add helpers for lock/unlock hpte
...
- DT endianness specification bindings
- Big endian 8250 serial support
- DT overlay unittest updates
- Various DT doc updates
- Compile fixes for OF_IRQ=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOG5kAAoJEMhvYp4jgsXihDgH/3pmPSjuRG1bhGssmnchHjWh
SU2eS2MZnlD60UqRt7jd3smCX2qL83tfwpFhOvCT9Mz775E7ggmYq9fS8pCYAbaD
x98mUrE2GzdUzlrL6RS8Z0ExjyGwbMoW3+cZtyPkmC6CsW0fwqEPmEyk7m+Hk8C3
w3pWG06o+G8UjiFmwbr8Pki2ykxvucr22NCzH4SS6bAD4QOrQO3v48QkUg7XFlVc
NHNzQbswL85uOJ7uuAbxg+s8TXkwcxUeMJEKldLrjuyppO3N1MjnOgCptnhVNOOb
zK+IsS378jMiNjAg2ui/BLH60N5yadkgk4+L4iPPy+y/yR61NCVXxRe11IQJxb0=
=rtv6
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
This series introduces preliminary ACPI 5.1 support to the arm64 kernel
using the "hardware reduced" profile. We don't support any peripherals
yet, so it's fairly limited in scope:
- Memory init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVNOC2AAoJELescNyEwWM08dIH/1Pn5xa04wwNDn0MOpbuQMk2
kHM7hx69fbXflTJpnZRVyFBjRxxr5qilA7rljAFLnFeF8Fcll/s5VNy7ElHKLISq
CB0ywgUfOd/sFJH57rcc67pC1b/XuqTbE1u1NFwvp2R3j1kGAEJWNA6SyxIP4bbc
NO5jScx0lQOJ3rrPAXBW8qlGkeUk7TPOQJtMrpftNXlFLFrR63rPaEmMZ9dWepBF
aRE4GXPvyUhpyv5o9RvlN5l8bQttiRJ3f9QjyG7NYhX0PXH3DyvGUzYlk2IoZtID
v3ssCQH3uRsAZHIBhaTyNqFnUIaDR825bvGqyG/tj2Dt3kQZiF+QrfnU5D9TuMw=
=zLJn
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
Pull ARM fixes from Russell King:
"A few fixes for the recently merged development updates:
- the update to convert a code branch in the procinfo structure
forgot to update the nommu code.
- VDSO only supported for V7 CPUs and later.
- VDSO build creates files which should be ignored by git but are not.
- ensure that make arch/arm/vdso/ doesn't build if it isn't enabled"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8344/1: VDSO: honor CONFIG_VDSO in Makefile
ARM: 8343/1: VDSO: add build artifacts to .gitignore
ARM: Fix nommu booting
ARM: 8342/1: VDSO: depend on CPU_V7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nong
-----END PGP SIGNATURE-----
Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao.
* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
eth: bf609 eth clock: add pclk clock for stmmac driver probe
blackfin: Wire up missing syscalls
arch: blackfin: kernel: kgdb: Remove unused function
dma: fix build error after update to v3.19
blackfin: io: define __raw_readx/writex with bfin_readx/writex
bf609: add resources for lcd nl8048
pm: sometimes wake up from suspend to RAM would fail
debug-mmrs: Eliminate all traces of the USB_PHY_TEST MMR
bf609: remove softswitch i2c configuration from adv7842 and adv7511 platform data
bf609: add platform data for soft switch devices on the video extenders
bf609: enable soft switch gpio driver by default
bf609: add gpio soft switch platform data for mcp23017 i2c devices
bf609: use new SND_BF6XX_PCM to choose audio pcm driver
bug[220] kgdb: change the smp cross core function entry
arch: blackfin: kernel: setup.c: Cleaning up missing null-terminate in conjunction with strncpy
blackfin: defconfigs: cleanup unused CONFIG_MTD_CHAR, add MTD_SPI_NOR for BF537-STAMP
Just the one change for v4.1-rc1. A minor cleanup of copy_thread().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=XxGr
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull Metag architecture updates from James Hogan:
"Just the one change for v4.1-rc1. A minor cleanup of copy_thread()"
* tag 'metag-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: copy_thread(): rename 'arg' argument to 'kthread_arg'
Commit cae2a173fe ("x86: clean up/fix 'copy_in_user()' tail zeroing")
fixed the failure case tail zeroing of one special case of the x86-64
generic user-copy routine, namely when used for the user-to-user case
("copy_in_user()").
But in the process it broke an even more unusual case: using the user
copy routine for kernel-to-kernel copying.
Now, normally kernel-kernel copies are obviously done using memcpy(),
but we have a couple of special cases when we use the user-copy
functions. One is when we pass a kernel buffer to a regular user-buffer
routine, using set_fs(KERNEL_DS). That's a "normal" case, and continued
to work fine, because it never takes any faults (with the possible
exception of a silent and successful vmalloc fault).
But Jan Beulich pointed out another, very unusual, special case: when we
use the user-copy routines not because it's a path that expects a user
pointer, but for a couple of ftrace/kgdb cases that want to do a kernel
copy, but do so using "unsafe" buffers, and use the user-copy routine to
gracefully handle faults. IOW, for probe_kernel_write().
And that broke for the case of a faulting kernel destination, because we
saw the kernel destination and wanted to try to clear the tail of the
buffer. Which doesn't work, since that's what faults.
This only triggers for things like kgdb and ftrace users (eg trying
setting a breakpoint on read-only memory), but it's definitely a bug.
The fix is to not compare against the kernel address start (TASK_SIZE),
but instead use the same limits "access_ok()" uses.
Reported-and-tested-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org # 4.0
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch e68410ebf6 ("crypto: x86/sha512_ssse3 - move SHA-384/512
SSSE3 implementation to base layer") changed the prototypes of the
core asm SHA-512 implementations so that they are compatible with
the prototype used by the base layer.
However, in one instance, the register that was used for passing the
input buffer was reused as a scratch register later on in the code,
and since the input buffer param changed places with the digest param
-which needs to be written back before the function returns- this
resulted in the scratch register to be dereferenced in a memory write
operation, causing a GPF.
Fix this by changing the scratch register to use the same register as
the input buffer param again.
Fixes: e68410ebf6 ("crypto: x86/sha512_ssse3 - move SHA-384/512 SSSE3 implementation to base layer")
Reported-By: Bobby Powers <bobbypowers@gmail.com>
Tested-By: Bobby Powers <bobbypowers@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The 'arg' argument to copy_thread() is only ever used when forking a new
kernel thread. Hence, rename it to 'kthread_arg' for clarity (and
consistency with do_fork() and other arch-specific implementations of
copy_thread()).
Signed-off-by: Alex Dowad <alexinbeijing@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Reported by the header checker (CONFIG_HEADERS_CHECK=y):
CHECK usr/include/asm/ (31 files)
./usr/include/asm/ptrace.h:77: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ley Foon Tan <lftan@altera.com>
The related syscalls are below which may cause samples/kdbus building
break in next-20150401 tree, the related information and error:
CALL scripts/checksyscalls.sh
<stdin>:1223:2: warning: #warning syscall kcmp not implemented [-Wcpp]
<stdin>:1226:2: warning: #warning syscall finit_module not implemented [-Wcpp]
<stdin>:1229:2: warning: #warning syscall sched_setattr not implemented [-Wcpp]
<stdin>:1232:2: warning: #warning syscall sched_getattr not implemented [-Wcpp]
<stdin>:1235:2: warning: #warning syscall renameat2 not implemented [-Wcpp]
<stdin>:1238:2: warning: #warning syscall seccomp not implemented [-Wcpp]
<stdin>:1241:2: warning: #warning syscall getrandom not implemented [-Wcpp]
<stdin>:1244:2: warning: #warning syscall memfd_create not implemented [-Wcpp]
<stdin>:1247:2: warning: #warning syscall bpf not implemented [-Wcpp]
<stdin>:1250:2: warning: #warning syscall execveat not implemented [-Wcpp]
[...]
HOSTCC samples/kdbus/kdbus-workers
samples/kdbus/kdbus-workers.c: In function ‘prime_new’:
samples/kdbus/kdbus-workers.c:930:18: error: ‘__NR_memfd_create’ undeclared (first use in this function)
p->fd = syscall(__NR_memfd_create, "prime-area", MFD_CLOEXEC);
^
samples/kdbus/kdbus-workers.c:930:18: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Remove the function kgdb_post_primary_code() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Rework of the prandom device with introduction of a new SHA-512 based
NIST SP 800-90 conform deterministic random bit generator.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After the file ptes have been removed the bit combination used to
encode non-linear mappings can be reused for the swap ptes. This
frees up a precious pte software bit. Reflect the change in the
swap encoding in the comments and do some cleanup while we are
at it.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dirty & young bit from the pmd is not copied correctly to the
pseudo pte in __pmd_to_pte. In fact it is not copied at all, the
bits get lost. As the old style huge page currently does not need
the dirty & young information this has no effect, but may be needed
in the future.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The new ebpf code uses e.g. the laal instruction which is part of the
interlocked-access facility 1 which again was introduced with z196.
So we must make sure the ebpf code generator depends on MARCH_Z196_FEATURES.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Replacing a 2K page table with a 4K page table while a VMA is active
for the affected memory region is fundamentally broken. Rip out the
page table reallocation code and replace it with a simple system
control 'vm.allocate_pgste'. If the system control is set the page
tables for all processes are allocated as full 4K pages, even for
processes that do not need it.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce KEXEC_CONTROL_MEMORY_GFP to allow the architecture code
to override the gfp flags of the allocation for the kexec control
page. The loop in kimage_alloc_normal_control_pages allocates pages
with GFP_KERNEL until a page is found that happens to have an
address smaller than the KEXEC_CONTROL_MEMORY_LIMIT. On systems
with a large memory size but a small KEXEC_CONTROL_MEMORY_LIMIT
the loop will keep allocating memory until the oom killer steps in.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Sometimes it fails to wake up from suspend to RAM, this is because
we would flush the data cache by assemble command FLUSHINV before
suspend to RAM, and there is a delay between this command execution
and cache flush completion. Add a 1uS delay to works around this.
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Interacting with the USB_PHY_TEST MMR through debugfs was causing wide-spread
chaos in the realm (kernel panic). Expunge all references to this demonic
register.
Signed-off-by: Andre Wolokita <Andre.Wolokita@analog.com>
Aneesh Kumar K.V