checkpatch complains about the allignment with open parenthesis.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch was complaining about space after cast. But the cast to void
is not required at that place.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch complains about missing blank line after declaration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Loopback mode can be activated by setting bit LBC (LoopBack
Control) of register ECSPI_TESTREG.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify spi-butterfly driver to use the new parallel port device model.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch complains about the allignment with open parenthesis.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch was complaining about space after cast. But the cast to void
is not required at that place.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark (and unmark) device nodes with the POPULATE flag as appropriate.
This is required to avoid multi probing when enabling and populating SPI
buses in DT overlays.
Based on commit 4f001fd301 ("i2c: Mark instantiated device nodes
with OF_POPULATE").
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Uninline spi_unregister_device() in preparation of adding more code to
it. Add kerneldoc documentation while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Occasionally the setup function will be called multiple times. Only request
the gpio the first time otherwise -EBUSY will occur on subsequent calls to
setup.
Reported-by: Joseph Bell <joe@iachieved.it>
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the topcliff-pch driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On 64-bit with CONFIG_SPI_DEBUG=y and #define VERBOSE:
drivers/spi/spidev.c:287:3: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type '__u32' [-Wformat=]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dw_spi_dma_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When submitting an identical spi_message multiple times via spi_sync
the spi_message.frame_length does not get reset to 0 in __spi_validate
before adding up all spi_transfer.len resulting in
frame_length > actual_length on all but the first spi_sync call.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
mtk_spi_probe() calls pm_runtime_enable(), after
pm_runtime_enable() is called, it should call
pm_runtime_disable() in the failure flow.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Handle EPROBE_DEFER explicitly so that we ensure that we get the DMA
channel specified in the device tree, instead of depending on the DMA
controller getting probed before us.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's not need to re-read and re-write SPI_CMD_REG, so remove it.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 8b136baa58 ("spi: pxa2xx: Detect number of enabled Intel LPSS SPI
chip select signals") added a block where lpss_ssp_setup() gets called
again for Intel LPSS SPI host controllers before checking number of chip
selects from the capabilities register.
There is no point in calling the function twice in probe so remove the
first call.
Reported-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds calls to pinctrl subsystem in order to switch pin states
on suspend/resume if you provide a "sleep" state in DT.
If no "sleep" state is provided in DT, these calls turn
to NOPs.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow transfers to set the transmission speed rather than using the
device max_speed_hz value. The SPI core makes sure that the speed_hz
value is always set on the transfer.
Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The s3c64xx platform data already contains a pointer to the
DMA filter function, but not to the associated data.
This simplifies the code and makes it more generic by
passing the data along with the filter function like
we do for other drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
With a 64-bit resource_size_t, we get a build warning on bcm63xx_spi_probe:
drivers/spi/spi-bcm63xx.c:565:16: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
As we are printing a resource, we can just use the %pr format
specifier that pretty-prints the address and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When only one device is present, it is not necessary to specify
cs_gpios, as the CS line can be controlled by the hardware
module.
Without this patch, older device tree bindings used before
37457607 "spi: mediatek: mt8173 spi multiple devices support"
would cause a panic on boot. This fixes the crash, and
re-introduces backward compatibility.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-bcm63xx.c: In function ‘bcm63xx_spi_setup_transfer’:
drivers/spi/spi-bcm63xx.c:207: warning: ‘clk_cfg’ may be used uninitialized in this function
While this is a false positive, it can easily be avoided by selecting
the default clock configuration first.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit ca5d248542 ("spi: Add THIS_MODULE to spi_driver in SPI core")
adds the new __spi_register_driver() function, but keeps the kerneldoc
for the spi_register_driver() function in place and forgets to add the
description for the new owner parameter.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the pxa2xx_spi_acpi_get_pdata() so that it can create platform data
also on platforms that do not support ACPI or if CONFIG_ACPI is not set.
Now it is expected that "pxa2xx-spi" platform device is either created with
explicit platform data or has an ACPI companion device.
However there is only little in pxa2xx_spi_acpi_get_pdata() that is really
dependent on ACPI companion and it can be reworked to cover also cases
where "pxa2xx-spi" device doesn't have ACPI companion and is created
without platform data.
Do this by renaming the pxa2xx_spi_acpi_get_pdata(), moving it outside of
CONFIG_ACPI test and changing a few runtime tests there to support non-ACPI
case. Only port/bus ID setting based on ACPI _UID is dependent on ACPI and
is moved to own function inside CONFIG_ACPI.
Purpose of this to support non-ACPI case for those PCI enumerated compound
devices that integrate both LPSS SPI host controller and integrated DMA
engine under the same PCI ID and which are registered in MFD layer instead
of in spi-pxa2xx-pci.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LPSS SPI in Intel Broxton is otherwise the same than in Intel Sunrisepoint
but it supports up to four chip selects per port and has different FIFO
thresholds. Patch adds support for two Broxton SoC variants.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI capabilities register located in private registers space of newer
Intel LPSS SPI host controllers tell in register bits 12:9 which chip
select signals are enabled.
Use that information for detecting the number of chip selects. For
simplicity we assume chip selects are enabled one after another without
disabled chip selects between. For instance CS0 | CS1 | CS2 but not
CS0 | CS1 | CS3.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel LPSS SPI host controllers in upcoming Intel platforms can have up
to 4 chip selects per port. Extend chip select control in
lpss_ssp_cs_control() by adding a code that selects the active chip
select output prior to changing the state. Detection for number of
enabled chip select signals will be added by another patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename a few defines that are specific to Intel LPSS SPI private
registers with LPSS prefix. It makes easier to distinguish them from
common defines.
Suggested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LS1043a and LS2080A in the Layerscape family also support DSPI, make
DSPI selectable for these hardwares.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
there's no need to call pm_runtime_get_sync()
followed by pm_runtime_put(). We should, instead,
just call pm_runtime_put_sync() and pm_runtime_disable().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some users have reported that in polled mode the driver fails randomly
to read the last word of the transfer.
The end condition used for the transmissions (in polled and irq mode)
has been the TX_EMPTY flag. But Lars-Peter Clausen has identified a delay
from the TX_EMPTY to the actual end of the data rx.
I believe that this race condition has not been detected until now
because of the latency added by the IRQ handler or the PCIe bridge.
This bugs affects setups with low latency access to the spi core.
This patch replaces the readout logic:
For all the words, except the last one, the TX_EMPTY flag is used (and
cached).
If !TX_EMPY or is the last word. The status register is read and the
RX_EMPTY flag is used.
The performance is not affected: there is an extra read of the
Status Register, but the readout can start as soon as there is a word
in the buffer.
Reported-by: Edward Kigwana <ekigwana@scires.com>
Initial-fix-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_register_driver helper macro that adds THIS_MODULE to
spi_driver for the registering driver. We rename and modify
the existing spi_register_driver to enable this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI controllers may need to be properly setup before chip selects
can be used. Therefore, wait until the spi controller has a chance
to perform their setup procedure before trying to use the chip
select.
This also insures that the chip selects pins are in a good
state before asseting them which otherwise may cause confusion.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset 0x60 is the offset of the data register defined as DW_SPI_DR in the
header file. Use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mt8173 IC spi HW has 4 gpio group, it's possible to support
max <= 4 slave devices, even mtk spi HW is not congruent to spi core.
1. When a device do a spi_message transfer, spi HW should know
which pad-group this device is on, and then writes pad-select
register.
2. Mtk pad-select register just selects which MISO pin HW will
receive data. For example, pad-select=1(select spi1 pins), HW just
receives data from spi1 MISO, but it still send waveform to all 4
group cs/clk/mosi. If cs pin in other groups is still spi mode,
after spi1 is selected(by active cs pin), devices on other group
will also be selected.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
controller_data is related with device, so move to master->setup
function.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mtk_spi_config() and mtk_spi_prepare_message() both initialize
spi register, so remove mtk_spi_config() and init all register
in mtk_spi_prepare_message().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building docs with make htmldocs, warnings about not having
a description for the return value are reported, i.e:
warning: No description found for return value of 'spi_register_driver'
Fix these by following the kernel-doc conventions explained in
Documentation/kernel-doc-nano-HOWTO.txt.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add more indentation to define lines for making them aligned with the
longest one. They would look messy after adding more long defines.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Upcoming Intel platforms use LPSS SPI_CS_CONTROL register bits 15:12 for
configuring the chip select polarities. Touch only chip select SW mode and
state bits when enabling the software chip select control in order to not
clear any other bits in the register.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy noticed numeric unique device ID is unsigned integer so convert it
using kstrtouint(). Actually integer in ACPI 2.0 and later is 64 bits
litte-endian unsigned integer but quite certainly having so big value here
would mean something extra than just the SPI bus number so it won't hurt to
assume only lower 32 bits carry the bus number for now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we call pxa2xx_ssp_get_clk_div() from pump_transfers() we may derive
pointer to struct chip_data from struct drv_data like it's done in the rest
of the functions. This will make it less errorprone.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The speed can be changed from transfer to transfer, that's why the messages
do not depict the actual values during ->setup(). Move debug messages from
->setup() to pump_transfers(). Get rid of leftovers as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed problem with setting spi mode 0 or 1 after setting mode 2 or 3
SPI_MODE_0 and SPI_MODE_1 requires clock low when inactive. SPI_MODE_2
and SPI_MODE_3 requires clk high when inactive.
Currently driver can just set bits in fields SCLK_PHA (SPI Clock/Data
Phase Control), SCLK_POL (SPI Clock Polarity Control),
SCLK_CTL (controls the inactive state of SCLK) ans SS_POL (SPI SS
Polarity Select) of ECSPIx_CONFIGREG register.
This patch allows driver to clear corresponding bits in these fields.
Signed-off-by: Andrew Y. Kuksov <qxovxp@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all register definitions and structs into the driver. This allows
us dropping the platform_data struct and drop any arch specific
includes. Make use of different device names to identify the version of
the block we have.
Since we now have full control over the message width, we can drop the
size check, which was broken anyway, since it never set ret to any error
code.
Also since we now have no arch depedendent resources, we can now allow
compiling it for any arch, hidden behind COMPILE_TEST.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA-slave configuration depends on the whether <= 8 or > 8 bits
are transferred per word, so we need to call
atmel_spi_dma_slave_config() with the correct value.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Since the "Switch driver to use transfer_one" change, the cs_change
behavior has changed and a channel chip select can still be
asserted when changing channel from a previous last transfer in a
message having the cs_change attribute.
Since there is no sense having multiple chip select being asserted at the
same time, disable all the remaining forced chip selects in a the
prepare_message called right before a spi_transfer_one_message call.
It ignores the current channel configuration in order to keep the
possibility to leave the chip select asserted between messages.
It fixes this bug on a DM8168 SoC ES2.1 Soc and an OMAP4 ES2.1 SoC.
It was hanging all the other channels transfers when a CHCONF_FORCE
is present on the wrong channel.
Fixes: b28cb9414d ("spi: omap2-mcspi: Switch driver to use transfer_one")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if GPIO pin is valid by API helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently all users aware about calling dw_spi_remove_host() with properly set
parameter. Remove unneeded check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the driver to use unfied device property API instead of OF one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pdev member is not used anywhere, thus remove it. Moreover struct
dw_spi_pci becomes an equivalent of struct dw_spi and therefore remove entire
struct dw_spi_pci.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper disables SPI controller and sets clock to 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tx_threshold and rx_threshold variables are not used anywhere. Remove them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point to have a separate variable for speed in ->transfer_one().
While here, remove !chip->clk_div from a condition since it is assigned
simultaneously with chip->speed_hz. We can do this safely because
a) transfer speed can't be higher than max_freq and therefore chip->clk_div
can be 0 only when chip->speed_hz is 0, and
b) transfer speed can't be 0, otherwise we will get division by zero
exception.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to carry over spi->bits_per_word and Co from ->setup() in
struct chip_data since ->transfer_one() will anyway take the transfer
parameters from struct spi_transfer. This is since SPI core validates both
bits_per_word transfer parameter and defaults to spi->bits_per_word in case
that per transfer parameter is not set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we recalculate cr0 each time we start a transfer the chip_data->cr0
becomes redundant. Remove it and related pieces.
This is a follow up to commit 0ed36990a9 (spi: dw: Remove needless if
statements).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name of the master device is set during registrationg which happens after
we issue the error message. Change it to plain struct device * to see which
device registration failed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use spi->cs_gpio directly to remove the following build warning:
drivers/spi/spi-davinci.c:219:6: warning: 'gpio' may be used uninitialized in this function
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently word completion interrupt is fired for transfer of every
word(8bit to 128bit in size). This adds a lot of overhead, and decreases
r/w throughput. It hardly takes 3us(@48MHz) for 128bit r/w to complete,
hence its better to poll on word complete bit to be set in
QSPI_SPI_STATUS_REG instead of using interrupts.
This increases the throughput by 30% in both read and write case.
So, switch to polling mode instead of interrupts to determine completion
of word transfer.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per discussion [1] the best choice is to set closest speed which is not
going over the asked one.
Do the same approach for Intel Quark boards.
[1] http://www.spinics.net/lists/linux-spi/msg03389.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Propagate the actual return code of __spi_validate_bits_per_word() in
spi_setup().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the initialization order of the HW so that the interrupt
is only requested after the HW is initialized
Also the use of irq_of_parse_and_map is replaced by platform_get_irq.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are strange issues with the auxiliary spi device that result
in "lost" data in the RX path if the fifo is filled by too much
(even though the status register is checked if new data can get filled
in).
This has been observed primarily for the interrupt case.
Polling works fine, probably because the RX fifo is pulled immediately
when in the tight polling loop.
For that reason we have to limit the pending bytes to less than 15
when filling the fifo in interrupt mode.
There also was an issue returning the "wrong" last 1/2 bytes
of a transfer when the transfer is not a multiple of 3 bytes.
(this impacted polling and interrupt modes)
Also fixed an overflow in the estimation of the transfer time used
to decide if we run in interrupt or polling mode (found with the
spi-bcm2835.c driver originally).
Reported-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the initialization order of the HW so that the interrupt
is only requested after the HW is initialized
Also the use of irq_of_parse_and_map is replaced by platform_get_irq.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Writing invalid command to QSPI_SPI_CMD_REG will terminate current
transfer and de-assert the chip select. This has to be done before
calling spi_finalize_current_message(). Because
spi_finalize_current_message() will mark the end of current message
transfer and schedule the next transfer. If the chipselect is not
de-asserted before calling spi_finalize_current_message() then the next
transfer will overlap with the previous transfer leading to data
corruption.
__spi_pump_message() can be called either from kthread worker context or
directly from the calling process's context. It is possible that these
two calls can race against each other. But race is serialized by
checking whether master->cur_msg == NULL (pointer to msg being handled
by transfer_one() at present). The master->cur_msg is set to NULL when
spi_finalize_current_message() is called on that message, which means
calling spi_finalize_current_message() allows __spi_sync() to pump next
message in calling process context.
Now if spi-ti-qspi calls spi_finalize_current_message() before we
terminate transfer at hardware side, if __spi_pump_message() is called
from process context then the successive transactions can overlap.
Fix this by moving writing invalid command to QSPI_SPI_CMD_REG to
before calling spi_finalize_current_message() call.
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the IRQs for SPI client devices, registered via device-tree,
are mapped when the client devices are registered. If the corresponding
irq-chip has not been probed yet, then the probing of the client device
will fail and will not be retried. Resolve this by mapping the IRQ at
probe time and allow the probe to be deferred if the IRQ is not yet
available.
If of_irq_get() returns an error that is not -EPROBE_DEFER, then assume
that the SPI client does not have an IRQ and set the IRQ number to zero
(which is equivalent to irq_of_parse_and_map()).
This is based on some inputs from Thierry Reding <treding@nvidia.com>.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the message control word parameters part of the register offsets
array so we have them all in one struct.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct guard CONFIG_CPU_BIG_ENDIAN and the *be accessors to
follow native endianness on big endian systems.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bcm2835 has 2 auxiliary spi bus masters spi1 and spi2.
This implements the driver to enable these devices.
The driver does not implement native chip-selects but uses
the aribtrary GPIO-chip-selects provided by the spi-chipselect.
Note that this driver relies on the fact that
the clock is implemented by the clk-bcm2835-aux driver,
which enables/disables the HW block when requesting/releasing
the clock.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the bitbang driver to use the generic implementation of
transfer_one_message. This simplifies the bitbang driver code and
provides benefits like the statistics in the generic implementation.
Successfully tested on a IMX6-based system (spi-imx) and on a MIPS-based
router (OpenWRT with spi-ath79).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove an unneeded check. The SPI core (__spi_validate) takes care
that these fields are always populated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not used since commit 8d94cc50aa ("[PATCH] spi: stabilize PIO mode
transfers on PXA2xx systems").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was leftover from the legacy pxa2xx DMA implementation and not needed
anymore so remove it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by switching from devm_ioremap to devm_ioremap_resource.
Checking the result of platform_get_resource is not needed as
devm_ioremap_resource checks the provided resource argument for NULL.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This makes possible to remove two if
statements and remove one code block that is never executed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get pointer to the struct acpi_device by using ACPI_COMPANION() macro. This
is more efficient than using ACPI_HANDLE() and acpi_bus_get_device().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Carry input clock of the controller in max_speed_hz of struct spi_master
instead of in own driver data. They mean the same thing and more over now
the max_speed_hz is not even set here.
As an added bonus this allows SPI core to validate that transfer speed is
not beyond the maximum input clock. This is not a problem in spi-pxa2xx as
the driver doesn't use transfer speed parameter directly but via input
clock divider calculation which will top at divide by one. However it's
better to validate speed before passing it here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sudip Mukherjee