R5000 and the Nevada CPUs (RM5230, RM5231, RM5260, RM5261, RM5270 and
RM5271) are basically the same CPU core and all are documented to require
two instructions separating a write to c0_pagemask, c0_entryhi, c0_entrylo0,
c0_entrylo1 or c0_index.
So far we were only providing on cycle before / after a TLBR/TLBWI
for R5000 but 3 cycles before and 1 cycles after for the Nevadas.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The microassembler used in tlbex.c does not notice if a label is redefined
resulting in relocations against such labels silently missrelocated.
The issues exists since commit add6eb04776db4189ea89f596cbcde31b899be9d
[Synthesize TLB exception handlers at runtime.] in 2.6.10 and went unnoticed
for so long because the relocations for the affected branches got computed
to do something *almost* sensible.
The issue affects R4000, R4400, QED/IDT RM5230, RM5231, RM5260, RM5261,
RM5270 and RM5271 processors.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
At some recent point arch/mips/include/asm/delay.h has started being
included into csrc-octeon.c where the __?delay() functions are defined.
This causes a compile failure due to conflicting declarations and
definitions of the functions.
It turns out that the generic definitions in arch/mips/lib/delay.c also
conflict.
Proposed fix: Declare the functions to take unsigned long parameters
just like asm-generic (and x86) does. Update __delay to agree
(__ndelay and __udelay need no change).
Bonus: Get rid of 'inline' from __delay() definition, as it is globally
visible, and the compiler should be making this decision itself (it does
in fact inline the function without being told to).
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There was a serious disconnect in the logic happening in
sparc_pmu_disable_event() vs. sparc_pmu_enable_event().
Event disable is implemented by programming a NOP event into the PCR.
However, event enable was not reversing this operation. Instead, it
was setting the User/Priv/Hypervisor trace enable bits.
That's not sparc_pmu_enable_event()'s job, that's what
sparc_pmu_enable() and sparc_pmu_disable() do .
The intent of sparc_pmu_enable_event() is clear, since it first clear
out the event type encoding field. So fix this by OR'ing in the event
encoding rather than the trace enable bits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal)
changed the interrupts to allow enabling sparse IRQ, but
accidentally added the omap3 INTC base to the local IRQ.
This causes the following:
twd: can't register interrupt 45 (-22)
twd_local_timer_register failed -22
The right fix is to not add any base, as it is a local
timer. For the OMAP44XX_IRQ_LOCALWDT we had defined earlier
there are no users, so no need to fix that.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This undoes commit 20f4665 "ARM: tegra: remove tegra_timer from
tegra_list_clks" by bringing back the tegra_timer clock. tegra_timer is
indeed a clock (hidden by the PERIPH_CLK macro) which should be added
to the tegra_list_clks.
The above commit caused tegra_init_timer() failing to get the clk
reference.
Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
[swarren: added the reverted commit's subject to this patch description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The timer variable is renamed to avoid confusion and symbol name clash
with the tegra_timer clock.
Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Change the type of variable from "unsigned long" to "u64".
This avoids the overflow while clock rate calculating.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 9e3c0066 (ARM: dts: imx6q-arm2: add pinctrl for uart and enet)
defines NANDF_CS pins as gpio in 'hog', assuming these two pins are
always used by usdhc3 in gpio mode as card-detection and
write-protection on ARM2 board. But it's not true. These pins are
shared by usdhc3 and gpmi-nand. We should have the pins functional
for gpmi-nand when usdhc3 is disabled.
Move the pins out of 'hog', so that pins only work in gpio mode as CD
and WP when usdhc3 is enabled, and otherwise they are available for
gpmi-nand.
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Intel PEBS in VT-x context uses the DS address as a guest linear
address, even though its programmed by the host as a host linear
address. This either results in guest memory corruption and or the
hardware faulting and 'crashing' the virtual machine. Therefore we have
to disable PEBS on VT-x enter and re-enable on VT-x exit, enforcing a
strict exclude_guest.
This patch enforces exclude_guest kernel side.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Robert Richter <robert.richter@amd.com>
Link: http://lkml.kernel.org/r/1347569955-54626-3-git-send-email-dsahern@gmail.com
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Use Kbuild infrastructure to handle the asm-generic headers
and remove the wrapper headers that call them.
This only affects headers that do nothing but include the generic
equivalent. It does not touch any header that does a little more.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
UAPI: (Scripted) Disintegrate arch/xtensa/include/asm
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
- correct use of .config #define name;
CONFIG_UNALIGNED_USER ---> CONFIG_XTENSA_UNALIGNED_USER
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Pete Delaney <piet@tensilica.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
- reference SRs by names where possible, not by numbers;
- get rid of __stringify around SR names where possible;
- remove unneeded SR names from asm/regs.h;
- add SREG_ prefix to remaining SR names;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Boot parameter tags with handlers are ignored like this:
[ 0.000000] Ignoring tag 0x00001003
[ 0.000000] Ignoring tag 0x00001001
[ 0.000000] Ignoring tag 0x00001004
because neither tagtable entries nor tag handlers appear in the vmlinux.
Fix tagtable definition attributes so that tag entries are not dropped.
Fix end of memory bank calculation in parse_tag_mem: it is intended to
round down to page size, but instead did something strange leading to
hang right after boot.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
When doing a fork (new VM), the new task has a mirror image of the
parent's stack, so keeps the same live register windows etc.
However when doing a clone with CLONE_VM, keeping the same VM
(eg. when creating a new thread), the child starts afresh on a new
stack -- it cannot share any part of the parent stack. It
especially cannot have the same live AR windows as the parent,
otherwise it will overwrite the parent stack on overflow, likely
causing corruption. (and so it did...)
Effectively, the register windows need to be spilled.
Turns out it's much easier to simply not copy parent register
windows when CLONE_VM is set.
Signed-off-by: Marc Gauthier <marc@tensilica.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
- fix memmove to correctly handle overlapping src and dst;
- fix memcpy loop ending conditions from signed '<=' to '!=';
- modify bcopy to call memmove;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
ISS serial console prints garbage instead of symbols printed via
rs_put_char. gcc optimizes away putting prined symbol into memory buffer
because there's no evidence that the buffer is used afterwards.
Make rs_put_char and rs_write use simc_write that has explicit wmb.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Simcalls that take memory buffer definitely need wmb or rmb to make sure
gcc doesn't optimize away code that fills the buffer.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
EHCI and UHCI devices in wm8505.dtsi should use IRQ 1 & 0
respectively - not 43 as used on newer models.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
This makes sure that the ARM Integrator device trees get compiled
during build.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
0a4b04dc29
(ARM: shmobile: use __iomem pointers for MMIO)
modified iomem pointers so that IOMEM() macro will be used,
but clock-r8a7779.c was out of target.
This patch fixes it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Commit fe04ddf7c2 ("kbuild: Do not package /boot and /lib in make
tar-pkg") accidentally reverted two previous kbuild commits. I don't
know what I was thinking.
This brings back changes made by commits 24cc7fb69a ("x86/kbuild:
archscripts depends on scripts_basic") and c1c1a59e37 ("firmware: fix
directory creation rule matching with make 3.80")
Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Mack reports an oops at boot with the latest kernels:
Internal error: Oops - undefined instruction: 0 [#1] SMP THUMB2
Modules linked in:
CPU: 0 Not tainted (3.6.0-11057-g584df1d #145)
PC is at cpsw_probe+0x45a/0x9ac
LR is at trace_hardirqs_on_caller+0x8f/0xfc
pc : [<c03493de>] lr : [<c005e81f>] psr: 60000113
sp : cf055fb0 ip : 00000000 fp : 00000000
r10: 00000000 r9 : 00000000 r8 : 00000000
r7 : 00000000 r6 : 00000000 r5 : c0344555 r4 : 00000000
r3 : cf057a40 r2 : 00000000 r1 : 00000001 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 50c5387d Table: 8f3f4019 DAC: 00000015
Process init (pid: 1, stack limit = 0xcf054240)
Stack: (0xcf055fb0 to 0xcf056000)
5fa0: 00000001 00000000 00000000 00000000
5fc0: cf055fb0 c000d1a8 00000000 00000000 00000000 00000000 00000000 00000000
5fe0: 00000000 be9b3f10 00000000 b6f6add0 00000010 00000000 aaaabfaf a8babbaa
The analysis of this is as follows. In init/main.c, we issue:
kernel_thread(kernel_init, NULL, CLONE_FS | CLONE_SIGHAND);
This creates a new thread, which falls through to the ret_from_fork
assembly, with r4 set NULL and r5 set to kernel_init. You can see
this in your oops dump register set - r5 is 0xc0344555, which is the
address of kernel_init plus 1 which marks the function as Thumb code.
Now, let's look at this code a little closer - this is what the
disassembly looks like:
c000d180 <ret_from_fork>:
c000d180: f03a fe08 bl c0047d94 <schedule_tail>
c000d184: 2d00 cmp r5, #0
c000d186: bf1e ittt ne
c000d188: 4620 movne r0, r4
c000d18a: 46fe movne lr, pc <-- XXXXXXX
c000d18c: 46af movne pc, r5
c000d18e: 46e9 mov r9, sp
c000d190: ea4f 3959 mov.w r9, r9, lsr #13
c000d194: ea4f 3949 mov.w r9, r9, lsl #13
c000d198: e7c8 b.n c000d12c <ret_to_user>
c000d19a: bf00 nop
c000d19c: f3af 8000 nop.w
This code was introduced in 9fff2fa0db (arm: switch to saner
kernel_execve() semantics). I have marked one instruction, and it's
the significant one - I'll come back to that later.
Eventually, having had a successful call to kernel_execve(), kernel_init()
returns zero.
In returning, it uses the value in 'lr' which was set by the instruction
I marked above. Unfortunately, this causes lr to contain 0xc000d18e -
an even address. This switches the ISA to ARM on return but with a non
word aligned PC value.
So, what do we end up executing? Well, not the instructions above - yes
the opcodes, but they don't mean the same thing in ARM mode. In ARM mode,
it looks like this instead:
c000d18c: 46e946af strbtmi r4, [r9], pc, lsr #13
c000d190: 3959ea4f ldmdbcc r9, {r0, r1, r2, r3, r6, r9, fp, sp, lr, pc}^
c000d194: 3949ea4f stmdbcc r9, {r0, r1, r2, r3, r6, r9, fp, sp, lr, pc}^
c000d198: bf00e7c8 svclt 0x0000e7c8
c000d19c: 8000f3af andhi pc, r0, pc, lsr #7
c000d1a0: e88db092 stm sp, {r1, r4, r7, ip, sp, pc}
c000d1a4: 46e81fff ; <UNDEFINED> instruction: 0x46e81fff
c000d1a8: 8a00f3ef bhi 0xc004a16c
c000d1ac: 0a0cf08a beq 0xc03493dc
I have included more above, because it's relevant. The PSR flags which
we can see in the oops dump are nZCv, so Z and C are set.
All the above ARM instructions are not executed, except for two.
c000d1a0, which has no writeback, and writes below the current stack
pointer (and that data is lost when we take the next exception.) The
other instruction which is executed is c000d1ac, which takes us to...
0xc03493dc. However, remember that bit 1 of the PC got set. So that
makes the PC value 0xc03493de.
And that value is the value we find in the oops dump for PC. What is
the instruction here when interpreted in ARM mode?
0: f71e150c ; <UNDEFINED> instruction: 0xf71e150c
and there we have our undefined instruction (remember that the 'never'
condition code, 0xf, has been deprecated and is now always executed as
it is now being used for additional instructions.)
This path also nicely explains the state of the stack we see in the oops
dump too.
The above is a consistent and sane story for how we got to the oops
dump, which all stems from the instruction at 0xc000d18a being wrong.
Reported-by: Daniel Mack <zonque@gmail.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "event" variable is a u16 so the shift will always wrap to zero
making the line a no-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org> v2.6.32..
Signed-off-by: Robert Richter <robert.richter@amd.com>
The prima2 platform advertises needing no mach/gpio.h header file,
but its pinctrl driver now has a sirfsoc_gpio_set_pull function
that uses constants defined in arch/arm/mach-prima2/include/mach/gpio.h,
which fails to build.
Fortunately, the sirfsoc_gpio_set_pull is not used anywhere in the
kernel, so we can safely remove it. Any out of tree drivers using
it will have to be converted to use proper pinctrl functions to
do the same.
Without this patch, building prima2_defconfig results in:
drivers/pinctrl/pinctrl-sirf.c: In function 'sirfsoc_gpio_set_pull':
drivers/pinctrl/pinctrl-sirf.c:1331:7: error: 'SIRFSOC_GPIO_PULL_NONE' undeclared (first use in this function)
drivers/pinctrl/pinctrl-sirf.c:1331:7: note: each undeclared identifier is reported only once for each function it appears in
drivers/pinctrl/pinctrl-sirf.c:1334:7: error: 'SIRFSOC_GPIO_PULL_UP' undeclared (first use in this function)
drivers/pinctrl/pinctrl-sirf.c:1338:7: error: 'SIRFSOC_GPIO_PULL_DOWN' undeclared (first use in this function)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
a2a47ca366
(ARM: __io abuse cleanup) cleanuped __io() -> IOMEM(),
but armadillo800eva was a outside of a target,
since "merge window" timing issue.
This patch cleanup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
The hostprogs need access to the CONFIG_* symbols found in
include/generated/autoconf.h. But commit abbf1590de ("UAPI: Partition
the header include path sets and add uapi/ header directories") replaced
$(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary
include paths.
This has the undesirable effect of breaking the EFI boot stub because
the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is
never compiled.
It should also be noted that because $(USERINCLUDE) isn't exported by
the top-level Makefile it's actually empty in arch/x86/boot/Makefile.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM update from Russell King:
"This is the final round of stuff for ARM, left until the end of the
merge window to reduce the number of conflicts. This set contains the
ARM part of David Howells UAPI changes, and a fix to the ordering of
'select' statements in ARM Kconfig files (see the appropriate commit
for why this happened - thanks to Andrew Morton for pointing out the
problem.)
I've left this as long as I dare for this window to avoid conflicts,
and I regenerated the config patch yesterday, posting it to our
mailing list for review and testing. I have several acks which
include successful test reports for it.
However, today I notice we've got new conflicts with previously unseen
code... though that conflict should be trivial (it's my changes vs a
one liner.)"
* 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate arch/arm/include/asm
Fix up fairly conflict in arch/arm/Kconfig (the select re-organization
vs recent addition of GENERIC_KERNEL_EXECVE)
The large platform selection choice should be sorted by option string
so it's easy to find the platform you're looking for. Fix the few
options which are out of this order.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixups for some corner cases, build issues, and some obvious bugs in
IRQ handling. No major changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlB2kfsACgkQ70gcjN2673PxDQCdF7rldDDP3yCjd98/utGgdpjS
EJAAnAqIbf8oWfvMzfzo22rImXo/naio
=sO+p
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://openrisc.net/jonas/linux
Pull OpenRISC updates from Jonas Bonn:
"Fixups for some corner cases, build issues, and some obvious bugs in
IRQ handling. No major changes."
* tag 'for-3.7' of git://openrisc.net/jonas/linux:
openrisc: mask interrupts in irq_mask_ack function
openrisc: fix typos in comments and warnings
openrisc: PIC should act on domain-local irqs
openrisc: Make cpu_relax() invoke barrier()
audit: define AUDIT_ARCH_OPENRISC
openrisc: delay: fix handling of counter overflow
openrisc: delay: fix loops calculation for __const_udelay
Pull powerpc uapi disintegration from Benjamin Herrenschmidt.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
UAPI: (Scripted) Disintegrate arch/powerpc/include/asm
- Do not export the COMPAT_* definitions to user
- Simplify the compat unistd32.h definitions and remove the
__SYSCALL_COMPAT guard
- Disintegrate the arch/arm64/include/asm/* headers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=1+LF
-----END PGP SIGNATURE-----
Merge tag 'arm64-uapi' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 uapi disintegration from Catalin Marinas:
"UAPI headers for arm64 together with some clean-up to make it
possible:
- Do not export the COMPAT_* definitions to user
- Simplify the compat unistd32.h definitions and remove the
__SYSCALL_COMPAT guard
- Disintegrate the arch/arm64/include/asm/* headers"
* tag 'arm64-uapi' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
UAPI: (Scripted) Disintegrate arch/arm64/include/asm
arm64: Do not export the compat-specific definitions to the user
arm64: Do not include asm/unistd32.h in asm/unistd.h
arm64: Remove unused definitions from asm/unistd32.h
Cleanups
Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
Add module event hooks for simplified debugging with gdb
Fixes
Fix kdb to stop paging with 'q' on bta and dmesg
Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
Allow kgdboc=kdb to setup kdb on the vga console
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uf0L
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB fixes and cleanups from Jason Wessel:
"Cleanups
- Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
- Add module event hooks for simplified debugging with gdb
Fixes
- Fix kdb to stop paging with 'q' on bta and dmesg
- Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
- The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
- Allow kgdboc=kdb to setup kdb on the vga console"
* tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
tty/console: fix warnings in drivers/tty/serial/kgdboc.c
kdb,vt_console: Fix missed data due to pager overruns
kdb: Fix dmesg/bta scroll to quit with 'q'
kgdboc: Accept either kbd or kdb to activate the vga + keyboard kdb shell
kgdb,x86: fix warning about unused variable
mips,kgdb: fix recursive page fault with CONFIG_KPROBES
kgdb: Add module event hooks
Pull Sparc updates from David Miller:
1) Updated syscall tracing fix from Al Viro.
2) SUN4V error reporting was deficient in several areas.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: fix ptrace interaction with force_successful_syscall_return()
sparc64: Fix deficiencies in sun4v error reporting.
Pull tile arch update from Chris Metcalf:
"The bulk of this change is the tile uapi disintegration. There is
also a one-line change in here to enable interrupts in
do_work_pending() to avoid a WARN_ON in _local_bh_enable_ip()."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: enable interrupts in do_work_pending()
UAPI: (Scripted) Disintegrate arch/tile/include/asm
UAPI: (Scripted) Disintegrate arch/tile/include/arch
Pull perf updates from Ingo Molnar:
"This tree includes some late late perf items that missed the first
round:
tools:
- Bash auto completion improvements, now we can auto complete the
tools long options, tracepoint event names, etc, from Namhyung Kim.
- Look up thread using tid instead of pid in 'perf sched'.
- Move global variables into a perf_kvm struct, from David Ahern.
- Hists refactorings, preparatory for improved 'diff' command, from
Jiri Olsa.
- Hists refactorings, preparatory for event group viewieng work, from
Namhyung Kim.
- Remove double negation on optional feature macro definitions, from
Namhyung Kim.
- Remove several cases of needless global variables, on most
builtins.
- misc fixes
kernel:
- sysfs support for IBS on AMD CPUs, from Robert Richter.
- Support for an upcoming Intel CPU, the Xeon-Phi / Knights Corner
HPC blade PMU, from Vince Weaver.
- misc fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
perf: Fix perf_cgroup_switch for sw-events
perf: Clarify perf_cpu_context::active_pmu usage by renaming it to ::unique_pmu
perf/AMD/IBS: Add sysfs support
perf hists: Add more helpers for hist entry stat
perf hists: Move he->stat.nr_events initialization to a template
perf hists: Introduce struct he_stat
perf diff: Removing the total_period argument from output code
perf tool: Add hpp interface to enable/disable hpp column
perf tools: Removing hists pair argument from output path
perf hists: Separate overhead and baseline columns
perf diff: Refactor diff displacement possition info
perf hists: Add struct hists pointer to struct hist_entry
perf tools: Complete tracepoint event names
perf/x86: Add support for Intel Xeon-Phi Knights Corner PMU
perf evlist: Remove some unused methods
perf evlist: Introduce add_newtp method
perf kvm: Move global variables into a perf_kvm struct
perf tools: Convert to BACKTRACE_SUPPORT
perf tools: Long option completion support for each subcommands
perf tools: Complete long option names of perf command
...
Pull third pile of kernel_execve() patches from Al Viro:
"The last bits of infrastructure for kernel_thread() et.al., with
alpha/arm/x86 use of those. Plus sanitizing the asm glue and
do_notify_resume() on alpha, fixing the "disabled irq while running
task_work stuff" breakage there.
At that point the rest of kernel_thread/kernel_execve/sys_execve work
can be done independently for different architectures. The only
pending bits that do depend on having all architectures converted are
restrictred to fs/* and kernel/* - that'll obviously have to wait for
the next cycle.
I thought we'd have to wait for all of them done before we start
eliminating the longjump-style insanity in kernel_execve(), but it
turned out there's a very simple way to do that without flagday-style
changes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to saner kernel_execve() semantics
arm: switch to saner kernel_execve() semantics
x86, um: convert to saner kernel_execve() semantics
infrastructure for saner ret_from_kernel_thread semantics
make sure that kernel_thread() callbacks call do_exit() themselves
make sure that we always have a return path from kernel_execve()
ppc: eeh_event should just use kthread_run()
don't bother with kernel_thread/kernel_execve for launching linuxrc
alpha: get rid of switch_stack argument of do_work_pending()
alpha: don't bother passing switch_stack separately from regs
alpha: take SIGPENDING/NOTIFY_RESUME loop into signal.c
alpha: simplify TIF_NEED_RESCHED handling
Pull third pile of VFS updates from Al Viro:
"Stuff from Jeff Layton, mostly. Sanitizing interplay between audit
and namei, removing a lot of insanity from audit_inode() mess and
getting things ready for his ESTALE patchset."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
procfs: don't need a PATH_MAX allocation to hold a string representation of an int
vfs: embed struct filename inside of names_cache allocation if possible
audit: make audit_inode take struct filename
vfs: make path_openat take a struct filename pointer
vfs: turn do_path_lookup into wrapper around struct filename variant
audit: allow audit code to satisfy getname requests from its names_list
vfs: define struct filename and have getname() return it
vfs: unexport getname and putname symbols
acct: constify the name arg to acct_on
vfs: allocate page instead of names_cache buffer in mount_block_root
audit: overhaul __audit_inode_child to accomodate retrying
audit: optimize audit_compare_dname_path
audit: make audit_compare_dname_path use parent_len helper
audit: remove dirlen argument to audit_compare_dname_path
audit: set the name_len in audit_inode for parent lookups
audit: add a new "type" field to audit_names struct
audit: reverse arguments to audit_inode_child
audit: no need to walk list in audit_inode if name is NULL
audit: pass in dentry to audit_copy_inode wherever possible
audit: remove unnecessary NULL ptr checks from do_path_lookup
getname() is intended to copy pathname strings from userspace into a
kernel buffer. The result is just a string in kernel space. It would
however be quite helpful to be able to attach some ancillary info to
the string.
For instance, we could attach some audit-related info to reduce the
amount of audit-related processing needed. When auditing is enabled,
we could also call getname() on the string more than once and not
need to recopy it from userspace.
This patchset converts the getname()/putname() interfaces to return
a struct instead of a string. For now, the struct just tracks the
string in kernel space and the original userland pointer for it.
Later, we'll add other information to the struct as it becomes
convenient.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
All the called functions expect interrupts to be enabled, and
now one of them has started to warn about it, so make it correct.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* allow kernel_execve() leave the actual return to userland to
caller (selected by CONFIG_GENERIC_KERNEL_EXECVE). Callers
updated accordingly.
* architecture that does select GENERIC_KERNEL_EXECVE in its
Kconfig should have its ret_from_kernel_thread() do this:
call schedule_tail
call the callback left for it by copy_thread(); if it ever
returns, that's because it has just done successful kernel_execve()
jump to return from syscall
IOW, its only difference from ret_from_fork() is that it does call the
callback.
* such an architecture should also get rid of ret_from_kernel_execve()
and __ARCH_WANT_KERNEL_EXECVE
This is the last part of infrastructure patches in that area - from
that point on work on different architectures can live independently.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- Register a pfn_is_ram helper to speed up reading of /proc/vmcore.
Bug-fixes:
- Three pvops call for Xen were undefined causing BUG_ONs.
- Add a quirk so that the shutdown watches (used by kdump) are not used with older Xen (3.4).
- Fix ungraceful state transition for the HVC console.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQeBKDAAoJEFjIrFwIi8fJDpwH/3nPBH82pJVxdLPBnmJhWuJR
voSPP0m9i69w/mc7wHtiRwK4lRMAUidgS77iBZkIT2cY0/NYvOKKBlMUitkYJFlK
dTVqr9O4iQcuG2yQk8+mXxC6NLH1VKOnSIyhqRswrePoBKzoHi/x7Y462a+tbxa9
lGBHT9/SqeYXyItRfkdfmAXFZcqIJqLRXEwRMvbky1U3s2QGy7CdIQgra0zWF+t1
ashNpaEBpH9Jy60VSpQtMpx8hWxd0W2NirNu+nACtTE5/MeuiBvKlPdEPC/rUbdJ
c5j5VYLjSxPCheY0sajK6pxKgHdfiqmMRlutzMVj3Egwilb0LBxv1018gRFzBu8=
=/qCG
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"This has four bug-fixes and one tiny feature that I forgot to put
initially in my tree due to oversight.
The feature is for kdump kernels to speed up the /proc/vmcore reading.
There is a ram_is_pfn helper function that the different platforms can
register for. We are now doing that.
The bug-fixes cover some embarrassing struct pv_cpu_ops variables
being set to NULL on Xen (but not baremetal). We had a similar issue
in the past with {write|read}_msr_safe and this fills the three
missing ones. The other bug-fix is to make the console output (hvc)
be capable of dealing with misbehaving backends and not fall flat on
its face. Lastly, a quirk for older XenBus implementations that came
with an ancient v3.4 hypervisor (so RHEL5 based) - reading of certain
non-existent attributes just hangs the guest during bootup - so we
take precaution of not doing that on such older installations.
Feature:
- Register a pfn_is_ram helper to speed up reading of /proc/vmcore.
Bug-fixes:
- Three pvops call for Xen were undefined causing BUG_ONs.
- Add a quirk so that the shutdown watches (used by kdump) are not
used with older Xen (3.4).
- Fix ungraceful state transition for the HVC console."
* tag 'stable/for-linus-3.7-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pv-on-hvm kexec: add quirk for Xen 3.4 and shutdown watches.
xen/bootup: allow {read|write}_cr8 pvops call.
xen/bootup: allow read_tscp call for Xen PV guests.
xen pv-on-hvm: add pfn_is_ram helper for kdump
xen/hvc: handle backend CLOSED without CLOSING
Pull timer core update from Thomas Gleixner:
- Bug fixes (one for a longstanding dead loop issue)
- Rework of time related vsyscalls
- Alarm timer updates
- Jiffies updates to remove compile time dependencies
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Cast raw_interval to u64 to avoid shift overflow
timers: Fix endless looping between cascade() and internal_add_timer()
time/jiffies: bring back unconditional LATCH definition
time: Convert x86_64 to using new update_vsyscall
time: Only do nanosecond rounding on GENERIC_TIME_VSYSCALL_OLD systems
time: Introduce new GENERIC_TIME_VSYSCALL
time: Convert CONFIG_GENERIC_TIME_VSYSCALL to CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Move update_vsyscall definitions to timekeeper_internal.h
time: Move timekeeper structure to timekeeper_internal.h for vsyscall changes
jiffies: Remove compile time assumptions about CLOCK_TICK_RATE
jiffies: Kill unused TICK_USEC_TO_NSEC
alarmtimer: Rename alarmtimer_remove to alarmtimer_dequeue
alarmtimer: Remove unused helpers & defines
alarmtimer: Use hrtimer per-alarm instead of per-base
alarmtimer: Implement minimum alarm interval for allowing suspend
We actually do not do anything about it. Just return a default
value of zero and if the kernel tries to write anything but 0
we BUG_ON.
This fixes the case when an user tries to suspend the machine
and it blows up in save_processor_state b/c 'read_cr8' is set
to NULL and we get:
kernel BUG at /home/konrad/ssd/linux/arch/x86/include/asm/paravirt.h:100!
invalid opcode: 0000 [#1] SMP
Pid: 2687, comm: init.late Tainted: G O 3.6.0upstream-00002-gac264ac-dirty #4 Bochs Bochs
RIP: e030:[<ffffffff814d5f42>] [<ffffffff814d5f42>] save_processor_state+0x212/0x270
.. snip..
Call Trace:
[<ffffffff810733bf>] do_suspend_lowlevel+0xf/0xac
[<ffffffff8107330c>] ? x86_acpi_suspend_lowlevel+0x10c/0x150
[<ffffffff81342ee2>] acpi_suspend_enter+0x57/0xd5
CC: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The hypervisor will trap it. However without this patch,
we would crash as the .read_tscp is set to NULL. This patch
fixes it and sets it to the native_read_tscp call.
CC: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
When compiling without CONFIG_DEBUG_RODATA the following
compiler warning is generated:
arch/x86/kernel/kgdb.c: In function 'kgdb_arch_set_breakpoint':
arch/x86/kernel/kgdb.c:749: warning: unused variable 'opc'
The variable instantiation needs to be inside the #ifdef to
make the warning go away.
Reported-by: Thiago Rafael Becker <trbecker@trbecker.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This fault was detected using the kgdb test suite on boot and it
crashes recursively due to the fact that CONFIG_KPROBES on mips adds
an extra die notifier in the page fault handler. The crash signature
looks like this:
kgdbts:RUN bad memory access test
KGDB: re-enter exception: ALL breakpoints killed
Call Trace:
[<807b7548>] dump_stack+0x20/0x54
[<807b7548>] dump_stack+0x20/0x54
The fix for now is to have kgdb return immediately if the fault type
is DIE_PAGE_FAULT and allow the kprobe code to decide what is supposed
to happen.
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull second set of media updates from Mauro Carvalho Chehab:
"Despite its size, most of the stuff here is trivial. This series
contains:
- s5p-mfc: additions at the driver and at the core to support H.264
hardware codec;
- Some improvements at s5p and davinci embedded drivers;
- Some V4L2 compliance fixes applied on a few drivers;
- Several random trivial patches, including several fixes and a few
new board support additions;
Notes:
1) Some Exynos media patches were dependent on some -arm fixes that
got merged on changeset 782cd9e. That's why this pull request is
based that changeset.
2) As promised, I reviewed the pending VB2 DMABUF series.
While setting a test environment, it was noticed that the upstream
support for Samsung Exynos 4 boards (smdk310 and Origen) are
broken upstream, likely due to regressions: both defconfigs are
wrong and regulator settings for both boards are broken. That,
allied with some bug at the dummy regulator driver, causes OOPSes
during boot time.
Long story short: even fixing the above, the proposed patches
OOPSed when running the DMABUF test. Not sure yet if the OOPSes
are due to some other undetected regressions, or due to some bug
on the patches.
Due to the above, DMABUF patches for vb2 got NACKed for 3.7."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Conflicts:
arch/arm/mach-davinci/include/mach/da8xx.h
- Complement the Nomadik pinctrl driver with alternate Cx functions
so it handles all oddities.
- A patch to the IRQdomain to reform the simple irqdomain to handle
IRQ descriptor allocation dynamically.
- Use the above feature in the Nomadik pin controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=UKY/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-3.7-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull second set of pinctrl patches from Linus Walleij:
"Here is a late pinctrl pull request with stuff that wasn't quite
tested at the first pull request.
The main reason to not hold off is that the modifications to
irq_domain_add_simple() as reviewed by Rob Herring introduce new
infrastructure for irqdomains that will be useful for the next cycle:
instead of sprinkling irq descriptor allocation all over the kernel
wherever a "legacy" domain is registered, which is necessary for any
platform using sparse IRQs, and many irq chips are say GPIO
controllers which may be used with several systems, some with sparse
IRQs some not, we push this into the irq_domain_add_simple() so we can
atleast do mistakes in one place.
The irq_domain_add_simple() is currently unused in the kernel, so I
need to provide a user. The Nomadik stuff that goes with are changes
to the driver I use day-to-day to make use of this facility (and a
dependency), so see it as a way to eat my own dogfood: if this blows
up the egg hits my face.
A second round of pinctrl patches for v3.7:
- Complement the Nomadik pinctrl driver with alternate Cx functions
so it handles all oddities.
- A patch to the IRQdomain to reform the simple irqdomain to handle
IRQ descriptor allocation dynamically.
- Use the above feature in the Nomadik pin controller."
* tag 'pinctrl-for-3.7-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: use simple or linear IRQ domain
irqdomain: augment add_simple() to allocate descs
pinctrl/nomadik: support other alternate-C functions
Pull second set of ARM updates from Russell King:
"This is the second set of ARM updates for this merge window.
Contained within are changes to allow the kernel to boot in hypervisor
mode on CPUs supporting virtualization, and cache flushing support to
the point of inner sharable unification, which are used by the
suspend/resume code to avoid having to do a full cache flush.
Also included is one fix for VFP code identified by Michael Olbrich."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: vfp: fix saving d16-d31 vfp registers on v6+ kernels
ARM: 7549/1: HYP: fix boot on some ARM1136 cores
ARM: 7542/1: mm: fix cache LoUIS API for xscale and feroceon
ARM: mm: update __v7_setup() to the new LoUIS cache maintenance API
ARM: kernel: update __cpu_disable to use cache LoUIS maintenance API
ARM: kernel: update cpu_suspend code to use cache LoUIS operations
ARM: mm: rename jump labels in v7_flush_dcache_all function
ARM: mm: implement LoUIS API for cache maintenance ops
ARM: virt: arch_timers: enable access to physical timers
ARM: virt: Add CONFIG_ARM_VIRT_EXT option
ARM: virt: Add boot-time diagnostics
ARM: virt: Update documentation for hyp mode entry support
ARM: zImage/virt: hyp mode entry support for the zImage loader
ARM: virt: allow the kernel to be entered in HYP mode
ARM: opcodes: add __ERET/__MSR_ELR_HYP instruction encoding
Pull pile 2 of execve and kernel_thread unification work from Al Viro:
"Stuff in there: kernel_thread/kernel_execve/sys_execve conversions for
several more architectures plus assorted signal fixes and cleanups.
There'll be more (in particular, real fixes for the alpha
do_notify_resume() irq mess)..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (43 commits)
alpha: don't open-code trace_report_syscall_{enter,exit}
Uninclude linux/freezer.h
m32r: trim masks
avr32: trim masks
tile: don't bother with SIGTRAP in setup_frame
microblaze: don't bother with SIGTRAP in setup_rt_frame()
mn10300: don't bother with SIGTRAP in setup_frame()
frv: no need to raise SIGTRAP in setup_frame()
x86: get rid of duplicate code in case of CONFIG_VM86
unicore32: remove pointless test
h8300: trim _TIF_WORK_MASK
parisc: decide whether to go to slow path (tracesys) based on thread flags
parisc: don't bother looping in do_signal()
parisc: fix double restarts
bury the rest of TIF_IRET
sanitize tsk_is_polling()
bury _TIF_RESTORE_SIGMASK
unicore32: unobfuscate _TIF_WORK_MASK
mips: NOTIFY_RESUME is not needed in TIF masks
mips: merge the identical "return from syscall" per-ABI code
...
Conflicts:
arch/arm/include/asm/thread_info.h
It's needed only in setup_sigcontext() and it's always reg - <constant>;
no point passing it all way down through the call chain. This is just
the signal.c side of that stuff; next will come the asm glue one...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Turn the slow side of work_pending into C function, including all
the looping. What we get out of that:
* we do _not_ call get_signal_to_deliver() with IRQs disabled
anymore
* no need to save/restore volatiles on each pass if there
turns to be more than one (unlikely, but still)
* all double-restart prevention is in C now.
* glue gets simpler.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In case we have both NEED_RESCHED and SIGPENDING/NOTIFY_RESUME,
handle the latter first. We'll get to original priorities in
the next commit, but now that allows to simplify the treatment
of NEED_RESCHED-only case nicely. Namely, now there no need to
preserve the data for restarts across the call of schedule() in
$work_resched; we can get there only if we had either returned
from syscall without SIGPENDING (in which case we should've
had no restart-worthy return value and want no restarts) or
already got through do_notify_resume() call (in which case we
want no restarts anymore). So we can just slap 0 into $19
instead of preserving it (and $20).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=EJUS
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
Applied on the top of changeset 782cd9e, as some of those patches
depend on some fixes that went via -arm tree.
* staging/for_v3.7: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
This patch adds #ifdef __KERNEL__ guards around the COMPAT_* definitions
to avoid exporting them to user. AArch32 user requiring the kernel
headers must use those generated with ARCH=arm.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
This patch only includes asm/unistd32.h where necessary and removes its
inclusion in the asm/unistd.h file. The __SYSCALL_COMPAT guard is
dropped.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
This patch removes the compat __NR_* definitions from the unistd32.h
file and only keeps those that are used by the AArch64 kernel with a new
__NR_compat_* prefix. The additional wrapper definitions in
arch/arm64/kernel/sys32.S have been removed and the actual wrapper names
included in the asm/unistd32.h file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Now that IRQ domains are in use, we should be acting on domain-local
IRQ numbers (hwirq) instead of 'global' ones.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Make cpu_relax() invoke barrier() to be the same as other arches.
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
The new SCCNXP driver supports the SC2681 chips used in RM400 machines.
We now use the new driver instead of the old SC26xx driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4417/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
LD arch/mips/pci/built-in.o
WARNING: arch/mips/pci/built-in.o(.devinit.text+0x2a0): Section mismatch in reference from the function malta_piix_func0_fixup() to the variable .init.data:pci_irq
The function __devinit malta_piix_func0_fixup() references
a variable __initdata pci_irq.
If pci_irq is only used by malta_piix_func0_fixup then
annotate pci_irq with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Originally added in 05b541489c48e7fbeec19a92acf8683230750d0a [Merge with
Linux 2.5.5.] over 10 years ago but never been used.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1100/1500 are similar to their DB-cousins but with a few
more devices on the bus.
This patch adds PB1100/1500 support to the existing DB1100/1500
code.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: lnux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1550 is more or less a DB1550 without the PCI IDE controller,
a more complicated (read: configurable) Flash setup and some other
minor changes. Like the DB1550 it can be automatically detected by
reading the CPLD ID register bits.
This patch adds PB1550 detection and setup to the DB1550 code.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Combine support for the DB1200/PB1200, DB1300 and DB1550 boards into
a single kernel image.
defconfig-generated image verified on DB1200, DB1300 and DB1550.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4335/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We don't have to do a separate shift to eliminate the software bits,
just rotate them into the fill and they will be ignored.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4294/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most supported systems currently hardwire cpu_has_dsp to 0, so we also
can disable support for cpu_has_dsp2 resulting in a slightly smaller
kernel.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[ralf@linux-mips.org: This patch really only detects the ASE and passes its
existence on to userland via /proc/cpuinfo. The DSP ASE Rev 2. adds new
resources but no resources that would need management by the kernel.]
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On a dual issue processor GCC generates code that saves a couple of
clock cycles per loop if we rearrange things slightly. Checking for
p != end saves a SLTU per loop, moving the increment to the middle can
let it dual issue on multi-issue processors.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4249/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add hardware performance counter support to kernel "perf" code for
BMIPS5000. The BMIPS5000 performance counters are similar to MIPS
MTI cores, so the changes were mostly made in perf_event_mipsxx.c
which is typically for MTI cores.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4109/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split the Kconfig option CONFIG_MIPS_MT_SMP into CONFIG_MIPS_MT_SMP
and CONFIG_MIPS_PERF_SHARED_TC_COUNTERS so some of the code used
for performance counters that are shared between threads can be used
for MIPS cores that are not MT_SMP.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4108/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The #ifdef for CONFIG_HW_PERF_EVENTS is not needed because the
Makefile will only compile the module if this config option is set.
This means that the code under #else would never be compiled. This
may have been done to leave the original broken code around for
reference, but the FIXME comment above the code already shows the
broken code.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4107/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PCI (Program Counter Interrupt) bit in the "cause" register
is mandatory for MIPS32R2 cores, but has also been added to some R1
cores (BMIPS5000). This change adds a cpu feature bit to make it
easier to check for and use this feature.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4106/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Change the indicator from 0xffffffff in the "event_id" member to
zero in the "cntr_mask" member. This removes the need to initialize
entries that are unsupported. This also solves a problem where the
number of entries in the table was increased based on a globel enum
used for all platforms, but the new unsupported entries were not added
for mips. This was leaving new table entries of all zeros that we not
marked UNSUPPORTED.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can save an instruction in the TLB Refill path for kernel mappings
by aligning swapper_pg_dir on a 64K boundary. The address of
swapper_pg_dir can be generated with a single LUI instead of
LUI/{D}ADDUI.
The alignment of __init_end is bumped up to 64K so there are no holes
between it and swapper_pg_dir, which is placed at the very beginning
of .bss.
The alignment of invalid_pmd_table and invalid_pte_table can be
relaxed to PAGE_SIZE. We do this by using __page_aligned_bss, which
has the added benefit of eliminating alignment holes in .bss.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-arch@vger.kernel.org,
Cc: linux-kernel@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Patchwork: https://patchwork.linux-mips.org/patch/4220/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I've maintained this patch, originally from Thiemo Seufer in 2004, for a
really long time, but I think it's time for it to get a look at for
possible inclusion. I have had no problems with it across various SGI
systems over the years.
To quote the post here:
http://www.linux-mips.org/archives/linux-mips/2004-12/msg00000.html
"the atomic functions use so far memory references for the inline
assembler to access the semaphore. This can lead to additional
instructions in the ll/sc loop, because newer compilers don't
expand the memory reference any more but leave it to the assembler.
The appended patch uses registers instead, and makes the ll/sc
arguments more explicit. In some cases it will lead also to better
register scheduling because the register isn't bound to an output
any more."
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4029/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull i2c-embedded changes from Wolfram Sang:
"The changes for i2c-embedded include:
- massive rework of the omap driver
- massive rework of the at91 driver. In fact, the old driver gets
removed; I am okay with this approach since the old driver was
depending on BROKEN and its limitations made it practically
unusable, so people used bitbanging instead. But even if there are
users, there is no platform_data or module parameter which would
need to be converted. It is just another driver doing I2C
transfers, just way better. Modifications of arch/arm/at91 related
files have proper acks from the maintainer.
- new driver for R-Car I2C
- devicetree and generic_clock conversions and fixes
- usual driver fixes and changes.
The rework patches have come a long way and lots of people have been
involved in creating/testing them. Most patches have been in
linux-next at least since 3.6-rc5. A few have been added in the last
week, I have to admit.
An unexpected (but welcome :)) peak in private life is the cause for
that. The "late" patches shouldn't cause any merge conflicts and I
will have a special eye on them during the stabilization phase. This
is an exception and I want to have the patches in place properly in
time again for the next kernels."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
MXS: Implement DMA support into mxs-i2c
i2c: add Renesas R-Car I2C driver
i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
i2c: algo: pca: Fix chip reset function for PCA9665
i2c: mpc: Wait for STOP to hit the bus
i2c: davinci: preparation for switch to common clock framework
omap-i2c: fix incorrect log message when using a device tree
i2c: omap: sanitize exit path
i2c: omap: switch over to autosuspend API
i2c: omap: remove unnecessary pm_runtime_suspended check
i2c: omap: switch to threaded IRQ support
i2c: omap: remove redundant status read
i2c: omap: get rid of the "complete" label
i2c: omap: resize fifos before each message
i2c: omap: simplify IRQ exit path
i2c: omap: always return IRQ_HANDLED
i2c: omap: simplify errata check
i2c: omap: bus: add a receiver flag
...
A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because firmware
no longer sets up all pin states before starting the kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was pre-agreed).
- A longer series of misc regression fixes and cleanups, warning removals,
etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vAh+
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because
firmware no longer sets up all pin states before starting the
kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was
pre-agreed).
- A longer series of misc regression fixes and cleanups, warning
removals, etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: pxa: armcore: fix PCI PIO warnings
ARM: integrator: use __iomem pointers for MMIO, part 2
ARM: assabet: fix bogus warning in get_assabet_scr (again)
ARM: shmobile: mark shmobile_init_late as __init
ARM: integrator_cp: fix build failure
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
...
Merge misc fixes from Andrew Morton:
"Followups, fixes and some random stuff I found on the internet."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (11 patches)
perf: fix duplicate header inclusion
memcg, kmem: fix build error when CONFIG_INET is disabled
rtc: kconfig: fix RTC_INTF defaults connected to RTC_CLASS
rapidio: fix comment
lib/kasprintf.c: use kmalloc_track_caller() to get accurate traces for kvasprintf
rapidio: update for destination ID allocation
rapidio: update asynchronous discovery initialization
rapidio: use msleep in discovery wait
mm: compaction: fix bit ranges in {get,clear,set}_pageblock_skip()
arch/powerpc/platforms/pseries/hotplug-memory.c: section removal cleanups
arch/powerpc/platforms/pseries/hotplug-memory.c: fix section handling code
we want syscall_trace_leave() called on exit from any syscall;
skipping its call in case we'd done force_successful_syscall_return()
is broken...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing error types, attributes, and report fields. Pad out
to 64-bytes.
Make string reporting cleaner and easier to extend in the future using
"const char *" arrays that index by either bit position, or absolute
field value.
Report the raw 64-byte error report as a sequence of u64s before the
annotated version.
Only report fields which are valid, given the context and the
attribute bits which are set.
For shutdown requests, use the local copy of the error report not the
one we just freed up back to the queue. Also, use orderly_poweroff()
just like the Domain Services shutdown request code does.
If the real-address reported is "-1" (unknown) try to disassemble the
instruction to report the effective address of the access. Only do
this in privileged mode.
Signed-off-by: David S. Miller <davem@davemloft.net>
Followups to d760afd4d2 ("memory-hotplug: suppress "Trying to free
nonexistent resource <XXXXXXXXXXXXXXXX-YYYYYYYYYYYYYYYY>" warning").
- use unsigned long type, as overflows are conceivable
- rename `i' to the less-misleading and more informative `section'
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All legacy PWM providers have now been moved to the PWM subsystem. The
plan for 3.8 is to adapt all board files to provide a lookup table for
PWM devices in order to get rid of the global namespace. Subsequently,
users of the legacy pwm_request() and pwm_free() functions can be
migrated to the new pwm_get() and pwm_put() functions. Once this has
been completed, the legacy API and the compatibility code in the core
can be removed.
In addition to the above, these changes also add support for configuring
the polarity of a PWM signal (currently only supported on ECAP and
EHRPWM) and include a much needed rework of the i.MX driver. Managed
functions to obtain and release a PWM device (devm_pwm_get() and
devm_pwm_put()) have been added and the pwm-backlight driver has been
updated to use them. If the PWM subsystem hasn't been enabled, dummy
functions are provided that allow the subsystem to safely compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the description
of the PWM specifier's second cell in the device tree representation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=MQ5V
-----END PGP SIGNATURE-----
Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"All legacy PWM providers have now been moved to the PWM subsystem.
The plan for 3.8 is to adapt all board files to provide a lookup table
for PWM devices in order to get rid of the global namespace.
Subsequently, users of the legacy pwm_request() and pwm_free()
functions can be migrated to the new pwm_get() and pwm_put()
functions. Once this has been completed, the legacy API and the
compatibility code in the core can be removed.
In addition to the above, these changes also add support for
configuring the polarity of a PWM signal (currently only supported on
ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
Managed functions to obtain and release a PWM device (devm_pwm_get()
and devm_pwm_put()) have been added and the pwm-backlight driver has
been updated to use them. If the PWM subsystem hasn't been enabled,
dummy functions are provided that allow the subsystem to safely
compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the
description of the PWM specifier's second cell in the device tree
representation."
* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
pwm: dt: Fix description of second PWM cell
pwm: Check for negative duty-cycle and period
pwm: Add Ingenic JZ4740 support
MIPS: JZ4740: Export timer API
pwm: Move PUV3 PWM driver to PWM framework
unicore32: pwm: Use managed resource allocations
unicore32: pwm: Remove unnecessary indirection
unicore32: pwm: Use module_platform_driver()
unicore32: pwm: Properly remap memory-mapped registers
pwm-backlight: Use devm_pwm_get() instead of pwm_get()
pwm: Move AB8500 PWM driver to PWM framework
pwm: Fix compilation error when CONFIG_PWM is not defined
pwm: i.MX: fix clock lookup
pwm: i.MX: use per clock unconditionally
pwm: i.MX: add devicetree support
pwm: i.MX: Use module_platform_driver
pwm: i.MX: add functions to enable/disable pwm.
pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
pwm: i.MX: factor out SoC specific functions
pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
...
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Pull second s390 update from Martin Schwidefsky:
"The big thing in this pull request is the UAPI patch from David, and
worth mentioning is the page table dumper. The rest are small
improvements and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/entry: fix svc number for TIF_SYSCALL system call restart
s390/mm,vmem: fix vmem_add_mem()/vmem_remove_range()
s390/vmalloc: have separate modules area
s390/zcrypt: remove duplicated include from zcrypt_pcixcc.c
s390/css_chars: remove superfluous ifdef
s390/chsc: make headers usable
s390/mm: let kernel text section always begin at 1MB
s390/mm: fix mapping of read-only kernel text section
s390/mm: add page table dumper
s390: add support to start the kernel in 64 bit mode.
s390/mm,pageattr: remove superfluous EXPORT_SYMBOLs
s390/mm,pageattr: add more page table walk sanity checks
s390/mm: fix pmd_huge() usage for kernel mapping
s390/dcssblk: cleanup device attribute usage
s390/mm: use pfmf instruction to initialize storage keys
s390/facilities: cleanup PFMF and HPAGE machine facility detection
UAPI: (Scripted) Disintegrate arch/s390/include/asm
Upgrade nomadik pinctrl driver to enable selection of other
alternate-C[1-4] functions on some specific ux500 SoC pins.
Handling of those functions is done thanks to PRCM GPIOCR
registers. This was previously managed in PRCMU driver and
it was not really convenient. Idea is to provide a common
way to control all alternate functions.
Note that this improvement does not support the old-fashioned way
used to control nomadik pins, namely the "nmk_config_pin()" function
and its derivatives.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull generic execve() changes from Al Viro:
"This introduces the generic kernel_thread() and kernel_execve()
functions, and switches x86, arm, alpha, um and s390 over to them."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (26 commits)
s390: convert to generic kernel_execve()
s390: switch to generic kernel_thread()
s390: fold kernel_thread_helper() into ret_from_fork()
s390: fold execve_tail() into start_thread(), convert to generic sys_execve()
um: switch to generic kernel_thread()
x86, um/x86: switch to generic sys_execve and kernel_execve
x86: split ret_from_fork
alpha: introduce ret_from_kernel_execve(), switch to generic kernel_execve()
alpha: switch to generic kernel_thread()
alpha: switch to generic sys_execve()
arm: get rid of execve wrapper, switch to generic execve() implementation
arm: optimized current_pt_regs()
arm: introduce ret_from_kernel_execve(), switch to generic kernel_execve()
arm: split ret_from_fork, simplify kernel_thread() [based on patch by rmk]
generic sys_execve()
generic kernel_execve()
new helper: current_pt_regs()
preparation for generic kernel_thread()
um: kill thread->forking
um: let signal_delivered() do SIGTRAP on singlestepping into handler
...
Notable changes:
* Basic writeback support for DISPC level. Writeback is not yet usable, though,
as we need higher level code to actually expose the writeback feature to
userspace.
* Rewriting the omapdss output drivers. We're trying to remove the hard links
between the omapdss and the panels, and this rewrite work moves us closer to
that goal.
* Cleanup and restructuring patches that have been made while working on device
tree support for omapdss. Device tree support is still some way ahead, but
these patches are good cleanups in themselves.
* Basic OMAP5 DSS support for DPI and DSI outputs.
* Workaround for the problem that GFX overlay's fifo is too small for high
resolution scenarios, causing underflows.
* Cleanups that remove dependencies to omap platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lcyJ
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.7' of git://gitorious.org/linux-omap-dss2/linux into fbdev-next
Omapdss driver changes for the 3.7 merge window.
Notable changes:
* Basic writeback support for DISPC level. Writeback is not yet usable, though,
as we need higher level code to actually expose the writeback feature to
userspace.
* Rewriting the omapdss output drivers. We're trying to remove the hard links
between the omapdss and the panels, and this rewrite work moves us closer to
that goal.
* Cleanup and restructuring patches that have been made while working on device
tree support for omapdss. Device tree support is still some way ahead, but
these patches are good cleanups in themselves.
* Basic OMAP5 DSS support for DPI and DSI outputs.
* Workaround for the problem that GFX overlay's fifo is too small for high
resolution scenarios, causing underflows.
* Cleanups that remove dependencies to omap platform code.
Pull UML changes from Richard Weinberger:
"UML receives this time only cleanups.
The most outstanding change is the 'include "foo.h"' do 'include
<foo.h>' conversion done by Al Viro.
It touches many files, that's why the diffstat is rather big."
* 'for-linus-37rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
typo in UserModeLinux-HOWTO
hppfs: fix the return value of get_inode()
hostfs: drop vmtruncate
um: get rid of pointless include "..." where include <...> will do
um: move sysrq.h out of include/shared
um/x86: merge 32 and 64 bit variants of ptrace.h
um/x86: merge 32 and 64bit variants of checksum.h
Pull sparc update from David Miller:
"This is just the UAPI commits for sparc via David Howells."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
UAPI: (Scripted) Disintegrate arch/sparc/include/asm
Pull slave-dmaengine updates from Vinod Koul:
"This time we have Andy updates on dw_dmac which is attempting to make
this IP block available as PCI and platform device though not fully
complete this time.
We also have TI EDMA moving the dma driver to use dmaengine APIs, also
have a new driver for mmp-tdma, along with bunch of small updates.
Now for your excitement the merge is little unusual here, while
merging the auto merge on linux-next picks wrong choice for pl330
(drivers/dma/pl330.c) and this causes build failure. The correct
resolution is in linux-next. (DMA: PL330: Fix build error) I didn't
back merge your tree this time as you are better than me so no point
in doing that for me :)"
Fixed the pl330 conflict as in linux-next, along with trivial header
file conflicts due to changed includes.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
dma: tegra: fix interrupt name issue with apb dma.
dw_dmac: fix a regression in dwc_prep_dma_memcpy
dw_dmac: introduce software emulation of LLP transfers
dw_dmac: autoconfigure data_width or get it via platform data
dw_dmac: autoconfigure block_size or use platform data
dw_dmac: get number of channels from hardware if possible
dw_dmac: fill optional encoded parameters in register structure
dw_dmac: mark dwc_dump_chan_regs as inline
DMA: PL330: return ENOMEM instead of 0 from pl330_alloc_chan_resources
DMA: PL330: Remove redundant runtime_suspend/resume functions
DMA: PL330: Remove controller clock enable/disable
dmaengine: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
DMA: PL330: Set the capability of pdm0 and pdm1 as DMA_PRIVATE
ARM: EXYNOS: Set the capability of pdm0 and pdm1 as DMA_PRIVATE
dma: tegra: use list_move_tail instead of list_del/list_add_tail
mxs/dma: Enlarge the CCW descriptor area to 4 pages
dw_dmac: utilize slave_id to pass request line
dmaengine: mmp_tdma: add dt support
dmaengine: mmp-pdma support
spi: davici - make davinci select edma
...
Core:
- Add DT properties for card detection (broken-cd, cd-gpios, non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't already
have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qyY5
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"Core:
- Add DT properties for card detection (broken-cd, cd-gpios,
non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't
already have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree
support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of
presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)"
* tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (67 commits)
mmc: core: Fixup broken suspend and eMMC4.5 power off notify
mmc: sdhci-spear: Add clk_{un}prepare() support
mmc: sdhci-spear: add device tree bindings
mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resume
mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator
mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirks
mmc: dt: Support "broken-cd" property in sdhci-pltfm
mmc: sdhci-s3c: fix the wrong number of max bus clocks
mmc: sh-mmcif: avoid oops on spurious interrupts
mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQ
mmc: sdhci-s3c: Fix crash on module insertion for second time
mmc: sdhci-s3c: Enable only required bus clock
mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration"
mmc: mxcmmc: fix bug that may block a data transfer forever
mmc: omap_hsmmc: Pass on the suspend failure to the PM core
mmc: atmel-mci: AP700x PDC is not connected to MCI
mmc: atmel-mci: DMA can be used with other controllers
mmc: mmci: use clk_prepare_enable and clk_disable_unprepare
mmc: sdhci-s3c: Add device tree support
mmc: dw_mmc: add support for exynos specific implementation of dw-mshc
...
From Tony Lindgren:
This branch contains regression fixes for omap4/5 ASoC
audio that were caused by the fact that u-boot stopped
muxing non essential pins.
As omap audio and dmaengine development happens on
these platforms, let's make sure they are usable.
Of course this should have been fixed earlier and
not during the -rc cycle.
* tag 'omap-for-v3.7-rc1/fixes-asoc-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
ARM: OMAP: board-4430-sdp: Pin mux configuration for audio needs
From Tony Lindgren:
These were agreed to be merged via arm soc tree as Rafael
is on vacation.
From Kevin Hilman <khilman@deeprootsystems.com>:
This series a couple bug fixes and a couple fixes that make this
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
* tag 'omap-for-v3.7-rc1/fixes-cpufreq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: PM: MPU DVFS: use generic CPU device for MPU-SS
cpufreq: OMAP: use get_cpu_device() instead of omap_device API
cpufreq: OMAP: fix clock usage to be SoC independent, remove plat/ includes
cpufreq: OMAP: remove unused <plat/omap-pm.h>
cpufreq: OMAP: ensure valid clock rate before scaling
From Kevin Hilman <khilman@deeprootsystems.com> via Tony Lindgren:
OMAP PM related fixes for v3.7-rc
* tag 'omap-for-v3.7-rc1/fixes-pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: SmartReflex: fix error path in init function
ARM: OMAP: SmartReflex: select CONFIG_POWER_SUPPLY in Kconfig
ARM: OMAP2+: PM: fix return value check in omap2_set_init_voltage()
ARM: OMAP2+: SmartReflex: fix return value check in sr_dev_init()
ARM: OMAP: omap_device: fix return value check in omap_device_build_ss()
ARM: OMAP: fix return value check in beagle_opp_init()
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Some OMAP fixes for the 3.7 merge window, fixing mismerges, branch
integration issues, and bugs after the arm-soc merges.
* tag 'omap-for-v3.7-rc1/fixes-hwmod-clock-signed-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
ARM: OMAP: omap3evm: fix new sparse warning
ARM: OMAP2+: hwmod data: Fix PMU interrupt definitions
ARM: am33xx: clk: Update clkdev table to add mcasp alias
From Tony Lindgren:
This branch contains one counter locking fix and an
alignment fix. Other fixes are warning fixes, fixes
for return value checks.
I've also included removal of some extra semicolons,
dropping of some duplicate includes, and an a change
for wl12xx enumeration that are not strictly fixes
but would be good to get out of the way for -rc1.
* tag 'omap-for-v3.7-rc1/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
AM35xx: Add missing hwmod entry for the HDQ/1-Wire present in AM3505/3517 CPUs.
ARM: OMAP2+: gpmc: annotate exit sections properly
ARM: OMAP: fix return value check in realtime_counter_init()
ARM: OMAP: hsmmc: fix return value check in omap_hsmmc_init_one()
OMAPDSS: fix return value check in create_dss_pdev()
ARM: OMAP2+: Add am335x evm and bone targets to common Makefile
arm: increase FORCE_MAX_ZONEORDER for TI AM33XX
ARM: OMAP: OMAP_DEBUG_LEDS needs to select LEDS_CLASS
ARM: OMAP: rx51: Fix a section mismatch warn
ARM: OMAP2+: Round of the carve out memory requested to section_size
ARM: OMAP: counter: add locking to read_persistent_clock
The it8152 PCI host used on the pxa/cm_x2xx machines
uses the old-style I/O window registration. This should
eventually get converted to pci_ioremap_io() but for
now, let's cast the IT8152_IO_BASE constant to an integer
type to get rid of the warnings.
Without this patch, building cm_x2xx_defconfig results in:
arch/arm/common/it8152.c: In function 'it8152_pci_setup':
arch/arm/common/it8152.c:287:18: warning: assignment makes integer from pointer without a cast [enabled by default]
arch/arm/common/it8152.c:288:16: warning: assignment makes integer from pointer without a cast [enabled by default]
arch/arm/common/it8152.c:291:17: warning: assignment makes integer from pointer without a cast [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
On NOMMU ARM, the __addr_ok() and __range_ok() macros do not evaluate
their arguments, which may lead to harmless build warnings in some
code where the variables are not used otherwise. Adding a cast to void
gets rid of the warning and does not make any semantic changes.
Without this patch, building at91x40_defconfig results in:
fs/read_write.c: In function 'rw_copy_check_uvector':
fs/read_write.c:684:9: warning: unused variable 'buf' [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
The flat_get_addr_from_rp() macro does not use the 'persistent' argument
on ARM, causing a harmless compiler warning. A cast to void removes
that warning.
Without this patch, building at91x40_defconfig results in:
fs/binfmt_flat.c: In function 'load_flat_file':
fs/binfmt_flat.c:746:17: warning: unused variable 'persistent' [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@canonical.com>
Sometimes we want the kernel build process to only print messages
on errors, e.g. in automated build testing. This uses the "kecho"
macro that the build system provides to hide a few informational
messages. Nothing changes for a regular "make" or "make V=1".
Without this patch, building any ARM kernel results in:
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Marek <mmarek@suse.cz>
The Linaro cross toolchain and probably others nowadays default to
building in THUMB2 mode. When building a kernel for a CPU that does
not support THUMB2, the compiler complains about incorrect flags.
We can work around this by setting -marm for all non-T2 builds.
-marm was passed unconditionally for C files previously, but nothing was
passed to the gcc frontend when processing .S files, resulting in a
warning. The assembler never defaults to ARM unless -Wa,-mthumb is
supplied explicitly, so the files were still assembled correctly.
This patch makes sure that -marm is passed for .S files too, and also
avoids the redundant gcc -marm -mthumb in Thumb kernels.
Without this patch, building assabet_defconfig results in:
usr/initramfs_data.S:1:0: warning: target CPU does not support THUMB instructions [enabled by default]
arch/arm/nwfpe/entry.S:1:0: warning: target CPU does not support THUMB instructions [enabled by default]
firmware/cis/PCMLM28.cis.gen.S:1:0: warning: target CPU does not support THUMB instructions [enabled by default]
(and many more)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
* The XEN_BALLOON code requires the balloon infrastructure that is not
getting built on ARM.
* The tmem hypercall is not available on ARM
* ARMv6 does not support cmpxchg on 16-bit words that are used in the
Xen grant table code, so we must ensure that Xen support is only
built on ARMv7-only kernels not combined ARMv6/v7 kernels.
* sys-hypervisor.c needs to include linux/err.h in order to use the
IS_ERR/PTR_ERR/ERR_PTR family of functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: xen-devel@lists.xensource.com
read_current_timer is used by get_cycles since "ARM: 7538/1: delay:
add registration mechanism for delay timer sources", and get_cycles
can be used by device drivers in loadable modules, so it has to
be exported.
Without this patch, building imote2_defconfig fails with
ERROR: "read_current_timer" [crypto/tcrypt.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Jonathan Austin <jonathan.austin@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
One such warning was recently fixed in a761cebf "ARM: Fix build warning
in arch/arm/mm/alignment.c" but only for the thumb2 case, this fixes
the other half.
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: error: 'offset.un' may be used uninitialized in this function
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
The recently added Emma Mobile GPIO driver calls set_irq_flags
and irq_set_chip_and_handler for the interrupts it exports and
it can be built as a module, which currently fails with
ERROR: "set_irq_flags" [drivers/gpio/gpio-em.ko] undefined!
We either need to replace the call to set_irq_flags with something
else or export that function. This patch does the latter.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Due to some interesting merges in the integrator code, not
all users of mmio pointers were converted before, this
fixes all warnings that got introduced as a consequence.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Russell fixed this bogus warning before in 2f3eca8b4f "Shut up gcc
warning in assabet.c", but apparently gcc has become smarter (or dumber)
since 2005, and the same warning came up again.
This uses the uninitialized_var() macro to convince gcc that the
variable is actually being initialized. 100 times in fact.
Without this patch, building assabet_defconfig results in:
arch/arm/mach-sa1100/assabet.c: In function 'fixup_assabet':
arch/arm/mach-sa1100/assabet.c:397:6: warning: 'scr' may be used uninitialized in this function [-Wuninitialized]
arch/arm/mach-sa1100/assabet.c:389:16: note: 'scr' was declared here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Patch 35f2b0bd59 "ARM: shmobile: Move definition of shmobile_init_late()
to header" moved the definition of the shmobile_init_late function, but
dropped the __init annotation, which is now causing warnings because
the function calls shmobile_suspend_init, which is also marked init.
Without this patch, building kota2_defconfig results in:
WARNING: vmlinux.o(.text+0xb7c8): Section mismatch in reference from the function shmobile_init_late() to the function .init.text:shmobile_suspend_init()
The function shmobile_init_late() references
the function __init shmobile_suspend_init().
This is often because shmobile_init_late lacks a __init
annotation or the annotation of shmobile_suspend_init is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Magnus Damm <damm@opensource.se>
Cc: Simon Horman <horms@verge.net.au>
The mls instruction is not available in ARMv6K or below, so we
should make the test conditional on at least ARMv7. ldrexd/strexd
are available in ARMv6K or ARMv7, which we can test by checking
the CONFIG_CPU_32v6K symbol.
/tmp/ccuMTZ8D.s: Assembler messages:
/tmp/ccuMTZ8D.s:22188: Error: selected processor does not support ARM mode `mls r0,r1,r2,r3'
/tmp/ccuMTZ8D.s:22222: Error: selected processor does not support ARM mode `mlshi r7,r8,r9,r10'
/tmp/ccuMTZ8D.s:22252: Error: selected processor does not support ARM mode `mls lr,r1,r2,r13'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Leif Lindholm <leif.lindholm@arm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=sTs2
-----END PGP SIGNATURE-----
Merge tag 'disintegrate-s390-20121009' of
git://git.infradead.org/users/dhowells/linux-headers
Pull UAPI patchset from David Howells:
"Can you merge the following branch into the s390 tree please.
This is to complete part of the UAPI disintegration for which the
preparatory patches were pulled recently."
Conflicts:
arch/s390/include/asm/chpid.h
The load of the svc number in the TIF_SYSCALL restart path needs to be
done with an instruction that loads all 64 bits of %r1, 'lh' only loads
32 bits. If the upper half of %r1 is not zero and has the msb set,
entry64.S will try to execute an svc with a really large number.
What will be in the upper half of %r1 depends on the code generated by
gcc for the functions on the do_signal() callchain.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
vmem_add_mem() should only then insert a large page if pmd_none() is true
for the specific entry. We might have a leftover from a previous mapping.
In addition make vmem_remove_range()'s page table walk code more complete
and fix a couple of potential endless loops (which can never happen :).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a special module area on top of the vmalloc area, which may be only
used for modules and bpf jit generated code.
This makes sure that inter module branches will always happen without a
trampoline and in addition having all the code within a 2GB frame is
branch prediction unit friendly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
No need for an ifdef __KERNEL__ since css_chars.h is not exported.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure that exported headers are save to be included by userspace
exploiting /dev/chsc.
Reported-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let the kernel text section always begin at 1MB. This allows to always have
a large frame in the identity mapping of the kernel image for beginning of
the text section, if the machine has EDAT1 support.
Moving the beginning from 64K to 1MB doesn't cost any memory, since we make
the memory between 64K and 1MB available for the page allocator.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Within the identity mapping the kernel text section is mapped read-only.
However when mapping the first and last page of the text section we must
round upwards and downwards respectively, if only parts of a page belong
to the section.
Otherwise potential rw data can be mapped read-only. So the rounding must
be done just the other way we have it right now.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is more or less the same as the x86 page table dumper which was
merged four years ago: 926e5392 "x86: add code to dump the (kernel)
page tables for visual inspection by kernel developers".
We add a file at /sys/kernel/debug/kernel_page_tables for debugging
purposes so it's quite easy to see the kernel page table layout and
possible odd mappings:
---[ Identity Mapping ]---
0x0000000000000000-0x0000000000100000 1M PTE RW
---[ Kernel Image Start ]---
0x0000000000100000-0x0000000000800000 7M PMD RO
0x0000000000800000-0x00000000008a9000 676K PTE RO
0x00000000008a9000-0x0000000000900000 348K PTE RW
0x0000000000900000-0x0000000001500000 12M PMD RW
---[ Kernel Image End ]---
0x0000000001500000-0x0000000280000000 10219M PMD RW
0x0000000280000000-0x000003d280000000 3904G PUD I
---[ vmemmap Area ]---
0x000003d280000000-0x000003d288c00000 140M PTE RW
0x000003d288c00000-0x000003d300000000 1908M PMD I
0x000003d300000000-0x000003e000000000 52G PUD I
---[ vmalloc Area ]---
0x000003e000000000-0x000003e000009000 36K PTE RW
0x000003e000009000-0x000003e0000ee000 916K PTE I
0x000003e0000ee000-0x000003e000146000 352K PTE RW
0x000003e000146000-0x000003e000200000 744K PTE I
0x000003e000200000-0x000003e080000000 2046M PMD I
0x000003e080000000-0x0000040000000000 126G PUD I
This usually makes only sense for kernel developers. The output
with CONFIG_DEBUG_PAGEALLOC is not very helpful, because of the
huge number of mapped out pages, however I decided for the time
being to not add a !DEBUG_PAGEALLOC dependency.
Maybe it's helpful for somebody even with that option.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do the switch to z/Architecture (alias 64 bit) mode early in head.S.
If the machine is already running in 64 bit mode the sigp turns into
a nop. With this change it doesn't matter in which mode the kernel
is started.
Reviewd-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove some EXPORT_SYMBOLs. There is no module code anywhere
which calls these pageattr functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current page table walk code in pageattr.c only checks for large pages
while walking the kernel page table, but happily assumes that everything
else is just fine.
Add more checks so we never access invalid memory regions.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
pmd_huge() will always return 0 on !HUGETLBFS, however we use that helper
function when walking the kernel page tables to decide if we have a
1MB page frame or not.
Since we create 1MB frames for the kernel 1:1 mapping independently of
HUGETLBFS this can lead to incorrect storage accesses since the code
can assume that we have a pointer to a page table instead of a pointer
to a 1MB frame.
Fix this by adding a pmd_large() primitive like other architectures have
it already and remove all references to HUGETLBFS/HUGETLBPAGE from the
code that walks kernel page tables.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make use of the pfmf instruction, if available, to initialize storage keys
of whole 1MB or 2GB frames instead of initializing every single page with
the sske instruction.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
MACHINE_HAS_PFMF and MACHINE_HAS_HPAGE actually have the same semantics:
the cpu has the EDAT1 facility installed in zArch mode. So remove one
of the feature flags in machine_flags and rename the other one to EDAT1.
The two old macros simply get mapped to MACHINE_HAS_EDAT1.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Olbrich reported that his test program fails when built with
-O2 -mcpu=cortex-a8 -mfpu=neon, and a kernel which supports v6 and v7
CPUs:
volatile int x = 2;
volatile int64_t y = 2;
int main() {
volatile int a = 0;
volatile int64_t b = 0;
while (1) {
a = (a + x) % (1 << 30);
b = (b + y) % (1 << 30);
assert(a == b);
}
}
and two instances are run. When built for just v7 CPUs, this program
works fine. It uses the "vadd.i64 d19, d18, d16" VFP instruction.
It appears that we do not save the high-16 double VFP registers across
context switches when the kernel is built for v6 CPUs. Fix that.
Cc: <stable@vger.kernel.org>
Tested-By: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It appears that performing a "movs pc, lr" to force the kernel into
SVC mode on the OMAP2420 (ARM1136) prevents the platform from booting
correctly (change introduced in 80c59da [ARM: virt: allow the kernel
to be entered in HYP mode]).
While the reason it fails is not understood yet (the same code runs
fine on the OMAP2430, ARM1136 as well), partially revert that change
for platforms that do not enter in HYP mode, preserving the new
feature and restoring a working kernel on the OMAP2420.
Reported-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Merge patches from Andrew Morton:
"A few misc things and very nearly all of the MM tree. A tremendous
amount of stuff (again), including a significant rbtree library
rework."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (160 commits)
sparc64: Support transparent huge pages.
mm: thp: Use more portable PMD clearing sequenece in zap_huge_pmd().
mm: Add and use update_mmu_cache_pmd() in transparent huge page code.
sparc64: Document PGD and PMD layout.
sparc64: Eliminate PTE table memory wastage.
sparc64: Halve the size of PTE tables
sparc64: Only support 4MB huge pages and 8KB base pages.
memory-hotplug: suppress "Trying to free nonexistent resource <XXXXXXXXXXXXXXXX-YYYYYYYYYYYYYYYY>" warning
mm: memcg: clean up mm_match_cgroup() signature
mm: document PageHuge somewhat
mm: use %pK for /proc/vmallocinfo
mm, thp: fix mlock statistics
mm, thp: fix mapped pages avoiding unevictable list on mlock
memory-hotplug: update memory block's state and notify userspace
memory-hotplug: preparation to notify memory block's state at memory hot remove
mm: avoid section mismatch warning for memblock_type_name
make GFP_NOTRACK definition unconditional
cma: decrease cc.nr_migratepages after reclaiming pagelist
CMA: migrate mlocked pages
kpageflags: fix wrong KPF_THP on non-huge compound pages
...
This is relatively easy since PMD's now cover exactly 4MB of memory.
Our PMD entries are 32-bits each, so we use a special encoding. The
lowest bit, PMD_ISHUGE, determines the interpretation. This is possible
because sparc64's page tables are purely software entities so we can use
whatever encoding scheme we want. We just have to make the TLB miss
assembler page table walkers aware of the layout.
set_pmd_at() works much like set_pte_at() but it has to operate in two
page from a table of non-huge PTEs, so we have to queue up TLB flushes
based upon what mappings are valid in the PTE table. In the second regime
we are going from huge-page to non-huge-page, and in that case we need
only queue up a single TLB flush to push out the huge page mapping.
We still have 5 bits remaining in the huge PMD encoding so we can very
likely support any new pieces of THP state tracking that might get added
in the future.
With lots of help from Johannes Weiner.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The transparent huge page code passes a PMD pointer in as the third
argument of update_mmu_cache(), which expects a PTE pointer.
This never got noticed because X86 implements update_mmu_cache() as a
macro and thus we don't get any type checking, and X86 is the only
architecture which supports transparent huge pages currently.
Before other architectures can support transparent huge pages properly we
need to add a new interface which will take a PMD pointer as the third
argument rather than a PTE pointer.
[akpm@linux-foundation.org: implement update_mm_cache_pmd() for s390]
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're going to be messing around with the PMD interpretation and layout
for the sake of transparent huge pages, so we better clearly document what
we're starting with.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've split up the PTE tables so that they take up half a page instead of
a full page. This is in order to facilitate transparent huge page
support, which works much better if our PMDs cover 4MB instead of 8MB.
What we do is have a one-behind cache for PTE table allocations in the
mm struct.
This logic triggers only on allocations. For example, we don't try to
keep track of free'd up page table blocks in the style that the s390 port
does.
There were only two slightly annoying aspects to this change:
1) Changing pgtable_t to be a "pte_t *". There's all of this special
logic in the TLB free paths that needed adjustments, as did the
PMD populate interfaces.
2) init_new_context() needs to zap the pointer, since the mm struct
just gets copied from the parent on fork.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reason we want to do this is to facilitate transparent huge page
support.
Right now PMD's cover 8MB of address space, and our huge page size is 4MB.
The current transparent hugepage support is not able to handle HPAGE_SIZE
!= PMD_SIZE.
So make PTE tables be sized to half of a page instead of a full page.
We can still map properly the whole supported virtual address range which
on sparc64 requires 44 bits. Add a compile time CPP test which ensures
that this requirement is always met.
There is a minor inefficiency added by this change. We only use half of
the page for PTE tables. It's not trivial to use only half of the page
yet still get all of the pgtable_page_{ctor,dtor}() stuff working
properly. It is doable, and that will come in a subsequent change.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Narrowing the scope of the page size configurations will make the
transparent hugepage changes much simpler.
In the end what we really want to do is have the kernel support multiple
huge page sizes and use whatever is appropriate as the context dictactes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When our x86 box calls __remove_pages(), release_mem_region() shows many
warnings. And x86 box cannot unregister iomem_resource.
"Trying to free nonexistent resource <XXXXXXXXXXXXXXXX-YYYYYYYYYYYYYYYY>"
release_mem_region() has been changed to be called in each
PAGES_PER_SECTION by commit de7f0cba96 ("memory hotplug: release
memory regions in PAGES_PER_SECTION chunks"). Because powerpc registers
iomem_resource in each PAGES_PER_SECTION chunk. But when I hot add
memory on x86 box, iomem_resource is register in each _CRS not
PAGES_PER_SECTION chunk. So x86 box unregisters iomem_resource.
The patch fixes the problem.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@austin.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In many places !pmd_present has been converted to pmd_none. For pmds
that's equivalent and pmd_none is quicker so using pmd_none is better.
However (unless we delete pmd_present) we should provide an accurate
pmd_present too. This will avoid the risk of code thinking the pmd is non
present because it's under __split_huge_page_map, see the pmd_mknotpresent
there and the comment above it.
If the page has been mprotected as PROT_NONE, it would also lead to a
pmd_present false negative in the same way as the race with
split_huge_page.
Because the PSE bit stays on at all times (both during split_huge_page and
when the _PAGE_PROTNONE bit get set), we could only check for the PSE bit,
but checking the PROTNONE bit too is still good to remember pmd_present
must always keep PROT_NONE into account.
This explains a not reproducible BUG_ON that was seldom reported on the
lists.
The same issue is in pmd_large, it would go wrong with both PROT_NONE and
if it races with split_huge_page.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I think zone->present_pages indicates pages that buddy system can management,
it should be:
zone->present_pages = spanned pages - absent pages - bootmem pages,
but is now:
zone->present_pages = spanned pages - absent pages - memmap pages.
spanned pages: total size, including holes.
absent pages: holes.
bootmem pages: pages used in system boot, managed by bootmem allocator.
memmap pages: pages used by page structs.
This may cause zone->present_pages less than it should be. For example,
numa node 1 has ZONE_NORMAL and ZONE_MOVABLE, it's memmap and other
bootmem will be allocated from ZONE_MOVABLE, so ZONE_NORMAL's
present_pages should be spanned pages - absent pages, but now it also
minus memmap pages(free_area_init_core), which are actually allocated from
ZONE_MOVABLE. When offlining all memory of a zone, this will cause
zone->present_pages less than 0, because present_pages is unsigned long
type, it is actually a very large integer, it indirectly caused
zone->watermark[WMARK_MIN] becomes a large
integer(setup_per_zone_wmarks()), than cause totalreserve_pages become a
large integer(calculate_totalreserve_pages()), and finally cause memory
allocating failure when fork process(__vm_enough_memory()).
[root@localhost ~]# dmesg
-bash: fork: Cannot allocate memory
I think the bug described in
http://marc.info/?l=linux-mm&m=134502182714186&w=2
is also caused by wrong zone present pages.
This patch intends to fix-up zone->present_pages when memory are freed to
buddy system on x86_64 and IA64 platforms.
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.fault now can retry. The retry can break state machine of .fault. In
filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
try, since the page is in page cache now, ra->mmap_miss is decreased. And
these are done in one fault, so we can't detect random mmap file access.
Add a new flag to indicate .fault is tried once. In the second try, skip
ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
I only tested x86, didn't test other archs, but looks the change for other
archs is obvious, but who knows :)
Signed-off-by: Shaohua Li <shaohua.li@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The x86 implementation of atomic_dec_if_positive is quite generic, so make
it available to all architectures.
This is needed for "swap: add a simple detector for inappropriate swapin
readahead".
[akpm@linux-foundation.org: do the "#define foo foo" trick in the conventional manner]
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide rb_insert_augmented() and rb_erase_augmented() through a new
rbtree_augmented.h include file. rb_erase_augmented() is defined there as
an __always_inline function, in order to allow inlining of augmented
rbtree callbacks into it. Since this generates a relatively large
function, each augmented rbtree user should make sure to have a single
call site.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement an interval tree as a replacement for the VMA prio_tree. The
algorithms are similar to lib/interval_tree.c; however that code can't be
directly reused as the interval endpoints are not explicitly stored in the
VMA. So instead, the common algorithm is moved into a template and the
details (node type, how to get interval endpoints from the node, etc) are
filled in using the C preprocessor.
Once the interval tree functions are available, using them as a
replacement to the VMA prio tree is a relatively simple, mechanical job.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As proposed by Peter Zijlstra, this makes it easier to define the augmented
rbtree callbacks.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
convert arch/x86/mm/pat_rbtree.c to the proposed augmented rbtree api
and remove the old augmented rbtree implementation.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells