Status register contains a lot of bits for reporting internal errors
inside Mali DP. Currently, we just silently ignore all of the errors,
that doesn't help when we are investigating different bugs, especially
on the FPGA models which have a lot of constraints, so we could easily
end up in AXI or underrun errors.
Add a new file called debug that contains an aggregate of the
errors reported by the Mali DP hardware.
E.g:
[root@alarm ~]# cat /sys/kernel/debug/dri/1/debug
[DE] num_errors : 167
[DE] last_error_status : 0x00000001
[DE] last_error_vblank : 385
[SE] num_errors : 3
[SE] last_error_status : 0x00e23001
[SE] last_error_vblank : 201
Changes since v2:
- Add lock to protect the errors stats.
- Add possibility to reset the error stats by writing anything to the
debug file.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP500 behaves differently from the rest of the Mali DP IP,
in that it does not have a one-shot mode and keeps writing the
content of the current frame to the provided memory area until
stopped. As a way of emulating the one-shot behaviour, we are
going to use the CVAL interrupt that is being raised at the
start of each frame, during prefetch phase, to act as End-of-Write
signal, but with a twist: we are going to disable the memory
write engine right after we're notified that it has been enabled,
using the knowledge that the bit controlling the enabling will
only be acted upon on the next vblank/prefetch.
CVAL interrupt will fire durint the next prefetch phase every time
the global CVAL bit gets set, so we need a state byte to track
the memory write enabling. We also need to pay attention during the
disabling of the memory write engine as that requires the CVAL bit
to be set in the control register, but we don't want to do that
during an atomic commit, as it will write into the hardware a partial
state.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali-DP display processors are able to write the composition result to a
memory buffer via the SE.
Add entry points in the HAL for enabling/disabling this feature, and
implement support for it on DP650 and DP550. DP500 acts differently and
so is omitted from this change.
Changes since v3:
- Fix missing vsync interrupt for DP550
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Internally Mali DP uses an RGB pipeline so video layers that support
YUV input buffers need to convert the input data to RGB. The YUV
buffers can have various encodings and this patch introduces support
for BT.601, BT.709 and BT.2020 encodings, both limited and full ranges.
This patch adds support for specifying the color encoding of the
input buffers for the planes that are backed by the video layers
and programs the YUV2RGB coefficients into hardware based on the
selected encoding.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[updated to use standard properties]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Apply image enhacement when we are upscaling by a factor of 2
or more in either direction.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Enable the scaling engine for upscaling a single plane using the polyphase
scaler. No image enhancement support or downscaling yet*, and composition
result scaling is not implemented.
* Downscaling a plane requires mclk > pxlclk.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
All DPs have a COLORADJ matrix which is applied prior to output gamma.
Attach that to the CTM property. Also, ensure the input CTM's coefficients
can fit in the DP registers' Q3.12 format.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add gamma via the DRM GAMMA_LUT/GAMMA_LUT_SIZE CRTC
properties. The expected LUT size is 4096 in order
to produce as accurate a set of segments as possible.
This version uses only the green channel's gamma curve
to set the hardware curve on DP550/650. For the sake of
simplicity, it uses the same table of coefficients for
all 3 curves on DP500.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Use rectangle 1 as a generic plane. Existing code already sets the smart
layer bounding box size + offset. The rectangles' offsets are relative
to the bounding box, so there is no need to set R1's offset (reset value
is 0), just its size which is the same as the bounding box.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Hardware has multiple (2 or 3, depending on model) stride
registers per layer; add a function that correctly takes that
into account. On hardware that only has 2 stride registers,
ensure that 3-plane (YUV) content has identical strides
for both chroma planes.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[Removed smart layer stride setup, comment and commit message clarifications]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
If the device-tree 'reg' node doesn't reserve enough
space for the DP, fail to bind.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[renamed added function to malidp_has_sufficient_address_space]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Refuse to bind if the device-tree compatible string
lists a different hardware version.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add support for the new family of Display Processors from ARM Ltd.
This commit adds basic support for Mali DP500, DP550 and DP650
parts, with only the display engine being supported at the moment.
Cc: David Brown <David.Brown@arm.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alexandru Gheorghe