Ability to tweak the interval between peer notifications has been
added in 07a4ddec3c ("bonding: add an option to specify a delay
between peer notifications") but the documentation was not updated.
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a spelling typo in bonding.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1386c36b30.
We don't want to encourage drivers to not report carrier status
correctly, therefore remove this commit.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a mixed environment it may be difficult to tell if your hardware
support carrier, if it does not it can always report true. With a new
use_carrier option of 2, we can check both carrier and link status
sequentially, instead of one or the other
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should be "802.3ad" like everywhere else in the document.
Signed-off-by: Axel Beckert <abe@deuxchevaux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers that use LLTX need to update trans_start of the netdev_queue.
(Most drivers don't use LLTX; stack does this update if .ndo_start_xmit
returned TX_OK).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port key has three components - user-key, speed-part, and duplex-part.
The LSBit is for the duplex-part, next 5 bits are for the speed while the
remaining 10 bits are the user defined key bits. Get these 10 bits
from the user-space (through the SysFs interface) and use it to form the
admin port-key. Allowed range for the user-key is 0 - 1023 (10 bits). If
it is not provided then use zero for the user-key-bits (default).
It can set using following example code -
# modprobe bonding mode=4
# usr_port_key=$(( RANDOM & 0x3FF ))
# echo $usr_port_key > /sys/class/net/bond0/bonding/ad_user_port_key
# echo +eth1 > /sys/class/net/bond0/bonding/slaves
...
# ip link set bond0 up
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
[jt: * fixed up style issues reported by checkpatch
* fixed up context from change in ad_actor_sys_prio patch]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an AD system, the communication between actor and partner is the
business between these two entities. In the current setup anyone on the
same L2 can "guess" the LACPDU contents and then possibly send the
spoofed LACPDUs and trick the partner causing connectivity issues for
the AD system. This patch allows to use a random mac-address obscuring
it's identity making it harder for someone in the L2 is do the same thing.
This patch allows user-space to choose the mac-address for the AD-system.
This mac-address can not be NULL or a Multicast. If the mac-address is set
from user-space; kernel will honor it and will not overwrite it. In the
absence (value from user space); the logic will default to using the
masters' mac as the mac-address for the AD-system.
It can be set using example code below -
# modprobe bonding mode=4
# sys_mac_addr=$(printf '%02x:%02x:%02x:%02x:%02x:%02x' \
$(( (RANDOM & 0xFE) | 0x02 )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )))
# echo $sys_mac_addr > /sys/class/net/bond0/bonding/ad_actor_system
# echo +eth1 > /sys/class/net/bond0/bonding/slaves
...
# ip link set bond0 up
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
[jt: fixed up style issues reported by checkpatch]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows user to randomize the system-priority in an ad-system.
The allowed range is 1 - 0xFFFF while default value is 0xFFFF. If user
does not specify this value, the system defaults to 0xFFFF, which is
what it was before this patch.
Following example code could set the value -
# modprobe bonding mode=4
# sys_prio=$(( 1 + RANDOM + RANDOM ))
# echo $sys_prio > /sys/class/net/bond0/bonding/ad_actor_sys_prio
# echo +eth1 > /sys/class/net/bond0/bonding/slaves
...
# ip link set bond0 up
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
[jt: * fixed up style issues reported by checkpatch
* changed how the default value is set in bond_check_params(), this
makes the default consistent between what gets set for a new bond
and what the default is claimed to be in the bonding options.]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing upcoming Yaogong patch (converting out of order queue
into an RB tree), I hit the max reordering level of linux TCP stack.
Reordering level was limited to 127 for no good reason, and some
network setups [1] can easily reach this limit and get limited
throughput.
Allow a new max limit of 300, and add a sysctl to allow admins to even
allow bigger (or lower) values if needed.
[1] Aggregation of links, per packet load balancing, fabrics not doing
deep packet inspections, alternative TCP congestion modules...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the Layer 2 hash factors with packet type ID field.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
CC: Pan Jiafei <Jiafei.Pan@freescale.com>
Signed-off-by: Jianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aggresive load balancing causes packet re-ordering as active
flows are moved from a slave to another within the group. Sometime
this aggresive lb is not necessary if the preference is for less
re-ordering. This parameter if used with value "0" disables
this dynamic flow shuffling minimizing packet re-ordering. Of course
the side effect is that it has to live with the static load balancing
that the hashing distribution provides. This impact is less severe if
the correct xmit-hashing-policy is used for the tlb setup.
The default value of the parameter is set to "1" mimicing the earlier
behavior.
Ran the netperf test with 200 stream for 1 min between two hosts with
4x1G trunk (xmit-lb mode with xmit-policy L3+4) before and after these
changes. Following was the command used for those 200 instances -
netperf -t TCP_RR -l 60 -s 5 -H <host> -- -r81920,81920
Transactions per second:
Before change: 1,367.11
After change: 1,470.65
Change-Id: Ie3f75c77282cf602e83a6e833c6eb164e72a0990
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-organized the xmit function for the lb mode separating tlb xmit
from the alb mode. This will enable use of the hashing policies
like 802.3ad mode. Also extended use of xmit-hash-policy to tlb mode.
Now the tlb-mode defaults to BOND_XMIT_POLICY_LAYER2 if the xmit policy
module parameter is not set (just like 802.3ad, or Xor mode).
Change-Id: I140257403d272df75f477b380207338d0f04963e
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's disabled because it's sometimes hard, in typical configs, to
make it work - because of the nature how the loadbalance modes work - as
it's hard to deliver valid arp replies to correct slaves by the switch.
However we still can use arp_validation in loadbalance with several other
configs, per example with arp_validate == 2 for backup with one broadcast
domain, without the switch(es) doing any balancing - this way we'd be (a
bit more) sure that the slave is up.
So, enable it to let users decide which one works/suits them best. Also
correct the mode limitation from BOND_OPT_ARP_VALIDATE.
CC: Nikolay Aleksandrov <nikolay@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new documentation for the packets_per_slave option available
for balance-rr mode.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new documentation for encap2+3 and encap3+4, also update the formula
for the old modes due to the changes.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
running bonding in ALB mode requires that learning packets be sent periodically,
so that the switch knows where to send responding traffic. However, depending
on switch configuration, there may not be any need to send traffic at the
default rate of 3 packets per second, which represents little more than wasted
data. Allow the ALB learning packet interval to be made configurable via sysfs
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Acked-by: Veaceslav Falico <vfalico@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we fail only when all of the ips in arp_ip_target are gone.
However, in some situations we might need to fail if even one host from
arp_ip_target becomes unavailable.
All situations, obviously, rely on the idea that we need *completely*
functional network, with all interfaces/addresses working correctly.
One real world example might be:
vlans on top on bond (hybrid port). If bond and vlans have ips assigned
and we have their peers monitored via arp_ip_target - in case of switch
misconfiguration (trunk/access port), slave driver malfunction or
tagged/untagged traffic dropped on the way - we will be able to switch
to another slave.
Though any other configuration needs that if we need to have access to all
arp_ip_targets.
This patch adds this possibility by adding a new parameter -
arp_all_targets (both as a module parameter and as a sysfs knob). It can be
set to:
0 or any (the default) - which works exactly as it's working now -
the slave is up if any of the arp_ip_targets are up.
1 or all - the slave is up if all of the arp_ip_targets are up.
This parameter can be changed on the fly (via sysfs), and requires the mode
to be active-backup and arp_validate to be enabled (it obeys the
arp_validate config on which slaves to validate).
Internally it's done through:
1) Add target_last_arp_rx[BOND_MAX_ARP_TARGETS] array to slave struct. It's
an array of jiffies, meaning that slave->target_last_arp_rx[i] is the
last time we've received arp from bond->params.arp_targets[i] on this
slave.
2) If we successfully validate an arp from bond->params.arp_targets[i] in
bond_validate_arp() - update the slave->target_last_arp_rx[i] with the
current jiffies value.
3) When getting slave's last_rx via slave_last_rx(), we return the oldest
time when we've received an arp from any address in
bond->params.arp_targets[].
If the value of arp_all_targets == 0 - we still work the same way as
before.
Also, update the documentation to reflect the new parameter.
v3->v4:
Kill the forgotten rtnl_unlock(), rephrase the documentation part to be
more clear, don't fail setting arp_all_targets if arp_validate is not set -
it has no effect anyway but can be easier to set up. Also, print a warning
if the last arp_ip_target is removed while the arp_interval is on, but not
the arp_validate.
v2->v3:
Use _bh spinlock, remove useless rtnl_lock() and use jiffies for new
arp_ip_target last arp, instead of slave_last_rx(). On bond_enslave(),
use the same initialization value for target_last_arp_rx[] as is used
for the default last_arp_rx, to avoid useless interface flaps.
Also, instead of failing to remove the last arp_ip_target just print a
warning - otherwise it might break existing scripts.
v1->v2:
Correctly handle adding/removing hosts in arp_ip_target - we need to
shift/initialize all slave's target_last_arp_rx. Also, don't fail module
loading on arp_all_targets misconfiguration, just disable it, and some
minor style fixes.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some details to bonding documentation on how backup slave arp
validation works.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Stephen proposed:
Since bonding supports configuration via iproute (netlink) and sysfs, I think
it is time to purge the old ifenslave code out of Documentation/networking
and update the documentation.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the "bonding" driver does not support load balancing outgoing
traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4)
are currently supported; this patch adds transmit hashing for IPv6 (and
TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the
bonding driver. In addition, bounds checking has been added to all
transmit hashing functions.
The algorithm chosen (xor'ing the bottom three quads of the source and
destination addresses together, then xor'ing each byte of that result into
the bottom byte, finally xor'ing with the last bytes of the MAC addresses)
was selected after testing almost 400,000 unique IPv6 addresses harvested
from server logs. This algorithm had the most even distribution for both
big- and little-endian architectures while still using few instructions. Its
behavior also attempts to closely match that of the IPv4 algorithm.
The IPv6 flow label was intentionally not included in the hash as it appears
to be unset in the vast majority of IPv6 traffic sampled, and the current
algorithm not using the flow label already offers a very even distribution.
Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets,
ie, they are not balanced based on layer 4 information. Additionally,
IPv6 packets with intermediate headers are not balanced based on layer
4 information. In practice these intermediate headers are not common and
this should not cause any problems, and the alternative (a packet-parsing
loop and look-up table) seemed slow and complicated for little gain.
Tested-by: John Eaglesham <linux@8192.net>
Signed-off-by: John Eaglesham <linux@8192.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The section titled "Configuring Bonding for Maximum Throughput" is
actually section twelve not thirteen, and there are a couple of words
spelled incorrectly.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Install commands should not be used to specify soft dependencies among
modules. When loading modules it's much better to have a softdep that
modprobe knows what's being done than having to fork/exec another
instance of modprobe to load the other module.
By using a softdep user has also an option to remove the dependencies
when removing the module (and if its refcount dropped to 0)
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
v2, based on Jay's review.
I kept the 'link must be up' part, because this is enforced in the code.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 655f8919d5
bonding: add min links parameter to 802.3ad
and commit ebd8e4977a
bonding: add all_slaves_active parameter
introduced new options to bonding, but didn't provide the documentation
for those options.
V2: add the default value for both options.
V3: document the exact behavior of min_links default value.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improves the documentation about how IGMP resend parameter
works, fix two missing checks and coding style issues.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For backward compatibility, we should retain the module parameters and
sysfs attributes to control the number of peer notifications
(gratuitous ARPs and unsolicited NAs) sent after bonding failover.
Also, it is possible for failover to take place even though the new
active slave does not have link up, and in that case the peer
notification should be deferred until it does.
Change ipv4 and ipv6 so they do not automatically send peer
notifications on bonding failover.
Change the bonding driver to send separate NETDEV_NOTIFY_PEERS
notifications when the link is up, as many times as requested. Since
it does not directly control which protocols send notifications, make
num_grat_arp and num_unsol_na aliases for a single parameter. Bump
the bonding version number and update its documentation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a6c36ee677 ("bonding: change list
contact to netdev@vger.kernel.org"), the mailing list for bonding
developpement was changed from bonding-devel to netdev.
Update the bonding documentation to reflect this change:
- bonding-devel is used for usage discussions (despite the name).
- netdev is used for developpement discussions.
Also remove the reference to the sourceforge bonding page, which is
deprecated.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding documentation used to provide configuration
details and examples for initscripts and sysconfig only.
This patch describe the third possible configuration:
/etc/network/interfaces.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow sysadmins to configure the number of multicast
membership report sent on a link failure event.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
v2: changed bonding module version, modified to apply on top of changes
from previous patch in series, and updated documentation to elaborate on
multiqueue awareness that now exists in bonding driver.
This patch give the user the ability to control the output slave for
round-robin and active-backup bonding. Similar functionality was
discussed in the past, but Jay Vosburgh indicated he would rather see a
feature like this added to existing modes rather than creating a
completely new mode. Jay's thoughts as well as Neil's input surrounding
some of the issues with the first implementation pushed us toward a
design that relied on the queue_mapping rather than skb marks.
Round-robin and active-backup modes were chosen as the first users of
this slave selection as they seemed like the most logical choices when
considering a multi-switch environment.
Round-robin mode works without any modification, but active-backup does
require inclusion of the first patch in this series and setting
the 'all_slaves_active' flag. This will allow reception of unicast traffic on
any of the backup interfaces.
This was tested with IPv4-based filters as well as VLAN-based filters
with good results.
More information as well as a configuration example is available in the
patch to Documentation/networking/bonding.txt.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases there is not desirable to switch back to primary interface when
it's link recovers and rather stay with currently active one. We need to avoid
packetloss as much as we can in some cases. This is solved by introducing
primary_reselect option. Note that enslaved primary slave is set as current
active no matter what.
Patch modified by Jay Vosburgh as follows: fixed bug in action
after change of option setting via sysfs, revised the documentation
update, and bumped the bonding version number.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a zero address hole bug in the bonding arp_ip_target list
that was causing the bond to ignore ARP replies (bugz 13006).
Instead of just setting the array entry to zero, we now
copy any additional entries down one slot, putting the
zero entry at the end. With this change we can now have
all the loops that walk the array stop when they hit a zero
since there will be no addresses after it.
Changes are based in part on code fragment provided in kernel:
bugzilla 13006:
http://bugzilla.kernel.org/show_bug.cgi?id=13006
by Steve Howard <steve@astutenetworks.com>
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements alternative aggregator selection policies
for 802.3ad. The existing policy, now termed "stable," selects the active
aggregator by greatest bandwidth, and only reselects a new aggregator
if the active aggregator is entirely disabled (no more ports or all ports
down).
This patch adds two new policies: bandwidth and count, selecting
the active aggregator by total bandwidth (like the stable policy) or by
the number of ports in the aggregator, respectively. These two policies
also differ from the stable policy in that they will reselect the active
aggregator when availability-related changes occur in the bond (e.g.,
link state change).
This permits "gang failover" within 802.3ad, allowing redundant
aggregators along parallel paths to always maintain the "best" aggregator
as the active aggregator (rather than having to wait for the active to
entirely fail).
This patch also updates the driver version to 3.5.0.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.
- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
IPv6-specific routines. Both regular bonds and VLANs over bonds
are supported.
- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
IPv6 Neighbor Advertisements that are sent on a failover event.
Default is 1.
- Creates two new IPv6 neighbor discovery functions:
ndisc_build_skb()
ndisc_send_skb()
These were required to support VLANs since we have to be able to
add the VLAN id to the skb since ndisc_send_na() and friends
shouldn't be asked to do this. These two routines are basically
__ndisc_send() split into two pieces, in a slightly different order.
- Updates Documentation/networking/bonding.txt and bumps the rev of bond
support to 3.4.0.
On failover, this new code will generate one packet:
- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
learn that the address has moved to the new slave.
Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This documentation patch hopes to clarify that the '+' was only needed
for Fedora 7 and Red Hat Enterprise Linux 5.0 and 5.1. After that the
IP addreses could be added as a comma separated list just like the
module option.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Permit bonding to function rationally if max_bonds is set to
zero. This will load the module, but create no master devices (which can
be created via sysfs).
Requires some change to bond_create_sysfs; currently, the
netdev sysfs directory is determined from the first bonding device created,
but this is no longer possible. Instead, an interface from net/core is
created to create and destroy files in net_class.
Based on a patch submitted by Phil Oester <kernel@linuxaces.com>.
Modified by Jay Vosburgh to fix the sysfs issue mentioned above and to
update the documentation.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support for sending multiple gratuitous ARPs during failovers
was added by commit:
commit 7893b2491a
Author: Moni Shoua <monis@voltaire.com>
Date: Sat May 17 21:10:12 2008 -0700
bonding: Send more than one gratuitous ARP when slave takes over
This change modifies that support to remove duplicated code,
add support for ARP monitor (the original only supported miimon), clear
the grat ARP counter in bond_close (lest a later "ifconfig up" immediately
start spewing ARPs), and add documentation for the module parameter.
Also updated driver version to 3.3.0.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a "follow" selection for fail_over_mac. This option
causes the MAC address to move from slave to slave as the active
slave changes. This is in addition to the existing fail_over_mac option
that causes the bond's MAC address to change during failover.
This new option is useful for devices that cannot tolerate
multiple ports using the same MAC address simultaneously, either
because it confuses them or incurs a performance penalty (as is the
case with some LPAR-aware multiport devices). Because the MAC of the
bond itself does not change, the "follow" option is slightly more
reliable during failover and doesn't change the MAC of the bond during
operation.
This patch requires a previous ARP monitor change to properly
handle RTNL during failovers.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Vincent Bernat